ComponentsThe analyzer package includes the following components: • SFF-8639 single-port interposer card• DC Power Adapter (12 volts)

Inspect the received shipping container for any damage. Unpack the container and account for each of the system components listed on the accompanying packing list. Visually inspect each component for absence of damage.

In the event of damage, notify the shipper and Teledyne LeCroy. Retain all shipping materials for shipper’s inspection.

IntroductionUse this document for quick installation and setup.

Teledyne LeCroy’s SFF-8639 single-port interposer card provides a quick and simple means for protocol analysis of Solid State Drives (SSDs) based on PCI Express (PCIe®) protocols. The SFF-8639 Interposer Card, used with a Summit Protocol Analyzer, enables PCIe bus traffic between a host backplane and SSD device to be monitored, captured, and recorded for protocol analysis. The card is compatible with the Summit T3-16, Summit T3-8, Summit T28 and Summit T24 and supports data rates of 2.5 GT/s (Gen1), 5 GT/s (Gen2) and 8 GT/s (Gen3).

SFF-8639 single-port interposer card

SFF-8639 Single Port Interposerfor PCI Express® 3.0Quick Start

1

2

3 ConnectionsPerform to the following steps to connect the Interposer (see the image below):1. Set the SW1 DIP switches to the desired clock selection.

Note: “REF_CLK_A” should be the default setting unless you are using an external clock reference source.2. Install the SFF-8639 device under test (DUT) into the connector on the interposer as shown (will fit 2.5” or 3” drives).3. Connect the Summit T3-8 Analyzer (or other compatible Teledyne LeCroy analyzer) to the interposer using the system iPass cable.

Note: On the Interposer side the iPass cable should be connected to the “x2 2.5GT/s / 5.0GT/s” port for SATA Express only. For all other applications, connect to the “x4 2.5GT/s / 5.0GT/s / 8.0GT/s” port (as shown in the diagram below).

4. Connect the analyzer to a host computer system using the USB port on the front panel of the Summit analyzer.5. If not already done, install the PETracer software on the host machine.6. Connect 12V DC using the AC adapter supplied with the interposer. (Make sure that the AC adapter is powered on).7. Power on the analyzer.8. Power on the host machine.9. Launch the Teledyne LeCroy software application to monitor, record and view PCI Express traffic passing through the SFF-8639

Interposer. 10. Install the Interposer into the host system connector.

SFF-8639 Interposer Interconnection Overview

Analyzer connection forSATA Express only

Analyzer connection forNVME & SCSI Express

iPass Y-cablePE010UCA-X

Summit T3-8 Analyzer

SF

F -

863

9 H

ost

Slo

t

Device Under Test (DUT)

Compatible with2.5" and 3" drives

SW1: Clock Select

Analyzer Clock 1 2

REF_CLK_A ON ON

EXT CLOCK OFF ON

12V DC from adapter supplied

External Clock Input (optional)USB (Factory use only)

Trademarks and ServicemarksTeledyne LeCroy and Summit T3-16, Summit T3-8, Summit T28 and Summit T24 are trademarks of Teledyne LeCroy.Microsoft and Windows are registered trademarks of Microsoft Inc.All other trademarks are property of their respective companies.

ChangesProduct specifications are subject to change without notice.Teledyne LeCroy reserves the right to revise the information in this document without notice or penalty.

Teledyne LeCroy Customer SupportOnline DownloadPeriodically check the Teledyne LeCroy Protocol Solutions Group web site for software updates and other support related to this product. Software updates are available to users with a current Maintenance Agreement.

Mail: 3385 Scott Blvd., Santa Clara, CA 95054-3115Web: teledynelecroy.com/Support/SoftwareDownload/E-mail: psgsupport@teledynelecroy.comTel: (800) 909-7112 (USA and Canada)Tel: (408) 653-1260 (worldwide)Fax: (408) 727-6622 (worldwide)

© 2013 Teledyne LeCroy, Inc. All rights reserved. Part Number: 923277-00 Rev AThis document may be printed and reproduced without additional permission, but all copies should contain this copyright notice.