Upload
alvaro-escalona-gtz
View
224
Download
0
Embed Size (px)
Citation preview
8/13/2019 Servicio g3
1/94
8/13/2019 Servicio g3
2/94
Warnings & Cautions
Warnings & Cautions
Follow the specified procedures in the indicated order to avoid personal injury
Note: Additional relevant information not covered in the service procedure.
Before starting a vehicle:
Sit in the driver's seat
Place shift lever in neutral
Set the parking brake
Before working on a vehicle or leaving the cab with engine running:
Place shift lever in neutral
Set the parking brake Block the wheels
When parking the vehicle or leaving the cab:
Place shift lever in neutral
Set the parking brake
Follow the specified procedures in the indicated order to avoid equipment malfunction or damage.
Do not release the parking brake or attempt to select a gear until the air pressure is at the correct level.
To avoid damage to the transmission during towing:
Place shift lever in neutral
Lift the drive wheels off of the ground or disconnect the driveline
Do not operate the vehicle if alternator lamp is lit or if gauges indicate low voltage.
WARNING
CAUTION
8/13/2019 Servicio g3
3/94
Table of Contents
General Information
Transmission Overview ............................................... 1How to use this Manual ............................................... 5Serial Tag Information and Model Nomenclature ........ 6
Service Procedure
Lubricant Filter Removal (AW3 Models Only) ............. 8Lubricant Filter Installation (AW3 Models Only) ........ 10Gear Select Sensor Removal ..................................... 12Gear Select Sensor Installation ................................. 14Rail Select Sensor Removal ...................................... 16Rail Select Sensor Installation ................................... 18Input Shaft Speed Sensor Removal ...........................20Input Shaft Speed Sensor Installation ....................... 22Main Shaft Speed Sensor Removal ........................... 25
Main Shaft Speed Sensor Installation ....................... 27Output Shaft Speed Sensor Removal ........................ 29Output Shaft Speed Sensor Installation ..................... 31Splitter Valve Removal .............................................. 33Splitter Valve Installation ........................................... 35Range Valve Removal ............................................... 37Range Valve Installation ............................................ 39Air Filter/Regulator Removal ..................................... 41Air Filter/Regulator Installation .................................. 43Inertia Brake Removal ............................................... 45Inertia Brake Installation ...........................................48Electric Shifter Removal ............................................ 51Electric Shifter Installation ........................................53Transmission Controller Removal .............................56Transmission Controller Installation ......................... 59Transmission Harness Removal ................................ 62Transmission Harness Installation ............................ 64Shift Control Removal ............................................... 66Shift Control Installation ........................................... 68Cobra Lever Removal ................................................ 70Cobra Lever Installation ............................................ 72
AppendixOperation .................................................................. 74Lubrication Specifications ......................................... 75
Inspection Procedures .............................................. 81Basic Troubleshooting .............................................. 82Air System Operation and Troubleshooting ............... 83Tool Specifications .................................................... 84Torque Specifications ................................................ 85Torque Overview ....................................................... 88
8/13/2019 Servicio g3
4/94
1
General Information
Transmission Overview
Heavy Duty 13-Speed DM3 & 18-Speed AS3
Air Filter Requlator
Range Valve Solenoid
Rail Select Sensor
Gear Select Sensor
Electric Shifter
Input ShaftSpeed Sensor
Main ShaftSpeed Sensor
Splitter Valve Solenoid
Output Shaft Speed Sensor
Transmission ECU
Inertia Brake(13-Speed DM3 Only)
Transmission Harness
8/13/2019 Servicio g3
5/94
2
General Information
Heavy Duty 10-Speed AS3 & DM3
Air Filter Regulator
Range Valve Solenoid
Rail Select Sensor
Gear Select Sensor
Electric Shifter
Input ShaftSpeed Sensor
Output ShaftSpeed Sensor
Main ShaftSpeed Sensor
Transmission ECU
Inertia Brake(10-Speed DM3 Only)
Transmission Harness
8/13/2019 Servicio g3
6/94
3
General Information
Medium Duty 6 & 5-Speed DM3
Output ShaftSpeed Sensor
Rail Select Sensor
Gear Select Sensor
Electric Shifter
Transmission ECU
Inertia Brake
Input ShaftSpeed Sensor Location
Transmission Harness
8/13/2019 Servicio g3
7/94
4
General Information
Medium Duty 6-Speed AW3
Electric Shifter
Gear Select Sensor
Rail Select Sensor
Output ShaftSpeed Sensor
Transmission ECU
Inertia Brake
Input ShaftSpeed Sensor Location
Wetclutch SolenoidConnector
Oil Pan and Filters
Transmission Harness
8/13/2019 Servicio g3
8/94
5
General Information
How to use this Manual
This publication is divided into three sections General Information, Service Repair Procedures and the Appendix.
General Information
This section contains the basic information like Transmission Overview, How to Use This Manual, and Serial Tag and ModelNomenclature.
Service Repair ProceduresA parts assembly view is included at the beginning of each procedure for disassembly, assembly, removal and installation. Belowthe parts assembly views is a numerical listing for each part with the component name.
AppendixThis section contains information like: Operation, Lubrication Specifications, Inspection (in base box manuals), Powerflow (inbas box manuals), Air System Operation and Troubleshooting (in base box manuals), Basic Troubleshooting (in base box manu-als), Tool Specifications, Torque Specifications, and the Torque Overview.
The service procedures in this manual are for transmission automation components only. To find the information you need, sim-ply locate the procedure in the Table of Contents, turn to the page specified, and follow the procedure. If you are unsure of a com-ponents name, you can reference the Transmission Overview pages.
To service the mechanical portion of the transmission system, refer to the specific transmission service manual.
8/13/2019 Servicio g3
9/94
6
General Information
Serial Tag Information and Model Nomenclature
Transmission model designation and other transmission identification information are stamped on the serial tag. To identify thetransmission model and serial number, locate the tag on the transmission and then locate the numbers as shown. Figure 1-1below shows the tag location for these transmissions.
When calling for service assistance or parts, have the model and serial numbers handy.
Do not remove or destroy the transmission identification tag!
Fig 1-1
Model
Serial
EatonTransmissions
R
Made In
RTLO-16913L-DM3
Eaton CorporationTransmission Div.Kalamazoo, MI. 49003
FullerR
8/13/2019 Servicio g3
10/94
7
General Information
Model NumberThe model number gives basic information about the transmission and is explained below. Use this number when calling for ser-vice assistance or replacement parts.
Transmission Tag
Serial NumberThe serial number is the sequential identification number of the transmission. Before calling for service assistance, write thenumber down as it may be needed.
Bill of material or Customer numberThis number may be located below the model and serial numbers. It is a reference number used by Eaton.
R
Roadranger
Twin Countershaft
Overdrive
T O -
Torque x 100
Design Level
Generation 3 Electronics
Gear Ratio
Forward Speeds
1 X 1 09 X - D M 310-Speed
Automaticw/DM Autoclutch
RoadrangerTwin Countershaft
OverdriveTorque x 100Design Level
R T O - 1 X 9 1 0 X - A S 3
Generation 3 ElectronicsAutoShiftGear RatioForward Speeds
F
Fuller
Overdrive
- 3
Torque x 100
Design Level
Generation 3 Electronics
Gear Ratio
Forward Speeds
X 4 0 6 X - D M
Automaticw/DM Autoclutch
X
RoadrangerTwin Countershaft
Low-InertiaOverdrive
R T L O M - 1 X 9 1 3 X - D M 3
Gen 3 ElectronicsAutomatic w/DM AutoclutchGear RatioForward SpeedsDesign LevelTorque x 100
1750 lb.ft. Torque inTop Two Gears Only
3
Fuller
Overdrive
Torque x 100
Design Level
AutoShift with WetClutch
Gear Ratio
Forward Speeds
F X X 0 64- X - A W
Generation 3 Electronics
10-Speed
6-Speed
6-Speed
13-Speed
F
FullerOverdrive
- 3
Torque x 100
Design Level
Generation 3 Electronics
Gear Ratio
Forward Speeds
X 4 0 5 X - D M
Automaticw/DM Autoclutch
X5-Speed
Roadranger
Twin CountershaftLow-Inertia
Overdrive
R T L O - 1 X 9 1 8 X - A S 3
Gen 3 ElectronicsAutoShiftGear RatioForward SpeedsDesign LevelTorque x 100
18-Speed
8/13/2019 Servicio g3
11/94
8
Service Procedure
Lubricant Filter Removal (AW3 Models Only)
Special Instructions
None
Special Tools
Basic Hand Tools
1. High Pressure Oil Filter (Large opening)2. Low Pressure Oil Filter (Small opening)3. Gasket4. Oil Pan5. Short Capscrew6. Long Capscrew7. Drain Plug
3
1
2
4
5
6
7
8/13/2019 Servicio g3
12/94
9
Service Procedure
Fluid may be hot.
1. Remove the drain plug and drain the fluid from the Wet-
Clutch portion of the transmission.
2. Using a 15mm socket, remove the oil pan mountingbolts. Record location of the long and short bolts.
3. Remove the WetClutch oil pan and gasket.
4. Using a 1/2 drive at the filter base, remove the two (2)WetClutch filters. Make sure filter seals are removed.
Note: The filters will contain fluid when they are removed.
WARNING
8/13/2019 Servicio g3
13/94
10
Service Procedure
Lubricant Filter Installation (AW3 Models Only)
Special Instructions
None
Special Tools
Basic Hand Tools
1. High Pressure Oil Filter (Large opening)2. Low Pressure Oil Filter (Small opening)3. Gasket4. Oil Pan5. Short Capscrew6. Long Capscrew7. Drain Plug
3
1
2
4
5
6
7
8/13/2019 Servicio g3
14/94
11
Service Procedure
1. Lubricate each filter seal ring with synthetic Dexron IIIprior to installation.
Note: The High and Low pressure filters are non-interchange-able.
Note: Clean filter seal mating surfaces on the transmission.
Note: Clean and remove all old gasket material from the mat-ing surfaces of the clutch housing and the oil pan.
2. Install the High-pressure filter with a 1/2 drive andtighten to 25-30 lbs. ft. (34-41 Nm).
3. Install the Low-pressure filter by hand and turn until theseal touches. Then, tighten with a 1/2 drive 3/4 to 1 fullturn.
4. Install a new gasket and the WetClutch oil pan.
Make sure to put the long and short bolts back in their
proper location to avoid damaging the transmission. Theshort bolts are used in the back of the oil pan.
5. Using a 15mm socket, install the mounting bolts andtighten to 30-35 lbs. ft. (41-47 Nm) using a cross pat-tern.
6. Install the oil pan drain plug and tighten to 34-48 lbs. ft.(46-64 Nm).
Note: Fill the WetClutch portion with the proper fluid (seepage 75)
CAUTION
8/13/2019 Servicio g3
15/94
12
Service Procedure
Gear Select Sensor Removal
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. Gasket
1
2
3
8/13/2019 Servicio g3
16/94
13
Service Procedure
1. Disconnect the Transmission Harness from the GearSelect Sensor.
Carefully allow the sensor to rotate (not snap) to a relaxedposition, or the sensor can snap when the hex key mountingscrews are removed.
2. Using a 5/32 hex key wrench, remove the two (2) sensorhex key mounting screws.
3. Remove the Gear Select Sensor and gasket from thehousing.
CAUTION
8/13/2019 Servicio g3
17/94
14
Service Procedure
Gear Select Sensor Installation
Special Instructions
Torques given below are in lbs. in.
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. Gasket
1
2
3
8/13/2019 Servicio g3
18/94
15
Service Procedure
1. Align the sensors tabs with the slots in the ElectricShifter rail. Then, insert the Gear Select Sensor, with gas-ket, into its mounting location.
Note: Install the sensor so the connector opening faces the
front of the transmission.
Carefully hold the sensor in position while installing the hexkey mounting screws, or the sensor can snap.
2. Using a 5/32" hex key wrench, install the hex key mount-ing screws and tighten to 21-27 lbs. in. (2.3-3.0 Nm).
3. Reconnect the Transmission Harness to the Gear SelectSensor.
CAUTION
8/13/2019 Servicio g3
19/94
16
Service Procedure
Rail Select Sensor Removal
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. Gasket
1
2
3
8/13/2019 Servicio g3
20/94
17
Service Procedure
1. Disconnect the Transmission Harness from the RailSelect Sensor.
Carefully allow the sensor to rotate to a relaxed position, orthe sensor can snap when the hex key mounting screws areremoved.
2. Using a 5/32 hex key wrench, remove the two (2) sensorhex key mounting screws.
3. Remove the Rail Select Sensor and gasket from thehousing.
CAUTION
8/13/2019 Servicio g3
21/94
8/13/2019 Servicio g3
22/94
19
Service Procedure
1. Align the sensors tabs with the slot in the Electric Shifterrail. Then, insert the Rail Select Sensor, with gasket, intoits mounting location.
Note: Install the sensor, so the connector opening faces the
right side of the transmission. (As viewed from the rearof the transmission)
Carefully hold the sensor in position while installing the hexkey mounting screws, or the sensor can snap.
2. Using a 5/32" hex key wrench, install the two (2) hex keymounting screws and tighten to 21-27 lbs. in. (2.3-3.0Nm).
3. Reconnect the Transmission Harness to the Rail SelectSensor.
CAUTION
8/13/2019 Servicio g3
23/94
20
Service Procedure
Input Shaft Speed Sensor Removal
Special Instructions
Input Shaft Speed Sensor location varies as follows:
Medium Duty - Top of Inertia Brake
Heavy Duty - Right front of Shift Bar Housing
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor
3. O-ring
1
2
3
8/13/2019 Servicio g3
24/94
21
Service Procedure
Heavy Duty Procedure1. Disconnect the Transmission Harness from the Input
Shaft Speed Sensor.
2. Using a 3/8" socket, remove the sensor retaining bolt.
3. Remove the Input Shaft Speed Sensor, with o-ring, fromthe transmission housing.
Medium Duty Procedure1. Disconnect the Transmission Harness from the Input
Shaft Speed Sensor.
Note: Drain the lubricant before removing the sensor.
2. Using a 3/8" wrench, remove the sensor retaining bolt.
3. Remove the Input Shaft Speed Sensor, with o-ring, fromthe transmission housing.
8/13/2019 Servicio g3
25/94
22
Service Procedure
Input Shaft Speed Sensor Installation
Special Instructions
Input Shaft Speed Sensor location varies as follows:
Medium Duty - Top of Inertia Brake
Heavy Duty - Right front of Shift Bar Housing.
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor
3. O-ring
1
2
3
8/13/2019 Servicio g3
26/94
23
Service Procedure
Heavy Duty Procedure
Clean the mounting surface on the housing and remove any
burrs or sharp edges.
Lubricate the o-ring with Eaton Fuller silicone #71214 orequivalent.
1. Using a smooth, twisting motion, fully insert the InputShaft Speed Sensor in the transmission housing opening.
2. Using a 3/8" socket, install the retaining bolt and tightento 8-10 lbs. ft. (11-13 Nm).
3. Reconnect the Transmission Harness to the Input ShaftSpeed Sensor.
Medium Duty Procedure
Clean the mounting surface on the housing and remove any
burrs or sharp edges.
Lubricate the o-ring with Eaton Fuller silicone #71214 orequivalent.
1. Using a smooth, twisting motion, fully insert the InputShaft Speed Sensor in the Inertia Brake opening.
2. Using a 3/8" wrench, install the sensor retaining bolt andtighten to 8-10 lbs. ft. (11-13 Nm).
IMPORTANT IMPORTANT
8/13/2019 Servicio g3
27/94
24
Service Procedure
3. Reconnect the Transmission Harness to the Input ShaftSpeed Sensor.
Note: Fill the transmission with lubricant (see page 75).
8/13/2019 Servicio g3
28/94
25
Service Procedure
Main Shaft Speed Sensor Removal
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. O-ring
1
2
3
8/13/2019 Servicio g3
29/94
26
Service Procedure
1. Disconnect the Transmission Harness from the MainShaft Speed Sensor.
2. Using a 3/8 socket, remove the sensor retaining bolt.
3. Remove the Main Shaft Speed Sensor, with o-ring, from
the transmission housing.
8/13/2019 Servicio g3
30/94
27
Service Procedure
Main Shaft Speed Sensor Installation
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. O-ring
1
2
3
8/13/2019 Servicio g3
31/94
28
Service Procedure
Clean the mounting surface on the housing and remove anyburrs or sharp edges.
Lubricate the o-ring with Eaton Fuller silicone #71214 orequivalent.
1. Using a smooth, twisting motion, fully insert the MainShaft Speed Sensor in the transmission housing opening.
2. Using a 3/8 socket, install the retaining bolt and tightento 8-10 lbs. ft. (11-13 N m).
3. Reconnect the Transmission Harness to the Main ShaftSpeed Sensor.
IMPORTANT
8/13/2019 Servicio g3
32/94
29
Service Procedure
Output Shaft Speed Sensor Removal
Special Instructions
The Output Shaft Speed Sensor location may vary depending on OEM design specifications. The sensor will be located at the 10oclock position for Heavy Duty and the 12 oclock for Medium Duty on the Output Shaft Housing.
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. O-ring
1
2
3
8/13/2019 Servicio g3
33/94
30
Service Procedure
Heavy Duty1. Disconnect the Transmission Harness from the Output
Shaft Speed Sensor.
2. Using a 13mm socket, remove the sensor retaining bolt.
3. Remove the Output Shaft Speed Sensor, with o-ring,from the transmission housing.
Medium Duty1. Disconnect the Transmission Harness from the Output
Shaft Speed Sensor.
2. Using a 3/8 socket, remove the sensor retaining bolt.
3. Remove the Output Shaft Speed Sensor, with o-ring,from the transmission housing.
8/13/2019 Servicio g3
34/94
31
Service Procedure
Output Shaft Speed Sensor Installation
Special Instructions
None.
Special Tools
Basic Hand Tools
1. Capscrew2. Sensor3. O-ring
1
2
3
8/13/2019 Servicio g3
35/94
32
Service Procedure
Heavy Duty Procedure
Clean the mounting surface on the housing and remove any
burrs or sharp edges.
Lubricate the o-ring with Eaton Fuller silicone #71214 orequivalent.
1. Using a smooth, twisting motion, fully insert the OutputShaft Speed Sensor in the transmission housing opening.
2. Using a 13mm socket, install the retaining bolt andtighten to 15-19 lbs. ft. (20-25 Nm).
3. Reconnect the Transmission Harness to the Output ShaftSpeed Sensor.
Medium Duty Procedure
Clean the mounting surface on the housing and remove any
burrs or sharp edges.
Lubricate the o-ring with Eaton Fuller silicone #71214 orequivalent.
1. Using a smooth, twisting motion, fully insert the OutputShaft Speed Sensor in the transmission housing opening.
2. Using a 3/8 socket, install the retaining bolt and tightento 8-10 lbs. ft. (11-13 Nm).
3. Reconnect the Transmission Harness to the Output ShaftSpeed Sensor.
IMPORTANT IMPORTANT
8/13/2019 Servicio g3
36/94
33
Service Procedure
Splitter Valve Removal
Special Instructions
The Splitter Valve may be difficult to remove from the housing because of the o-rings.
Special Tools
Basic Hand Tools
1. Capscrew2. Valve3. O-rings
1
2
3
8/13/2019 Servicio g3
37/94
34
Service Procedure
1. Relieve system air pressure by draining the air tanks onthe vehicle. When air pressure is relieved, disconnect theTransmission Harness from the Splitter Valve assembly.
Note: The harness should be removed from the Splitter Valve
tie-down, prior to removing the capscrews.
2. Using a 5/16 wrench, remove the four (4) mounting cap-screws from the Splitter valve.
Do not use a hammer to loosen the Splitter Valve in thehousing or it could be damaged.
3. Lift and remove the Splitter Valve from the housing.
CAUTION
8/13/2019 Servicio g3
38/94
35
Service Procedure
Splitter Valve Installation
Special Instructions
Torques give below are in lbs. in.
Special Tools
Basic Hand Tools
1. Capscrew2. Valve3. O-rings
1
2
3
8/13/2019 Servicio g3
39/94
36
Service Procedure
Lubricate o-rings with Eaton Fuller silicone #71214 orequivalent.
The valve is keyed to fit its mounting location. Take care toalign the key in the valve with the notch in the housing.
1. Install and push the Splitter Valve down into the housing.
2. Using a 5/16 wrench, install the four (4) mounting cap-screws and tighten to 21-27 lbs. in.(2.3-3.0 Nm) using across pattern.
3. Reconnect the Transmission Harness to the Splitter Valveand close all air tank drains.
Note: Install the Splitter harness back into the tie-down on theSplitter Valve.
IMPORTANT
8/13/2019 Servicio g3
40/94
37
Service Procedure
Range Valve Removal
Special Instructions
The Range Valve may be difficult to remove from the transmission housing because of the o-rings.
Special Tools
Basic Hand Tools
1. Capscrew2. Valve3. O-rings
1
2
3
8/13/2019 Servicio g3
41/94
38
Service Procedure
1. Relieve system air pressure by draining air tanks on thevehicle. When air pressure has been relieved, disconnectthe Transmission Harness from the Range Valve.
Note: The harness should be removed from the Range Valve
tie-down prior to removing the capscrews.
2. Using a 5/16 socket, remove the four (4) mounting cap-screws from the Range Valve.
Do not use a hammer to loosen the Range Valve in thehousing or it could be damaged.
3. Lift and remove the Range Valve from the housing.
CAUTION
8/13/2019 Servicio g3
42/94
39
Service Procedure
Range Valve Installation
Special Instructions
Torques given below are in lbs. in.
Special Tools
Basic Hand Tools
1. Capscrew2. Valve3. O-rings
1
2
3
8/13/2019 Servicio g3
43/94
40
Service Procedure
Lubricate o-rings with Eaton Fuller silicone #71214 orequivalent.
The valve is keyed to fit its mounting location. Take care toalign the key in the valve with the notch in the housing.
1. Install and push the Range Valve down into the housing.
2. Using a 5/16 socket, install the (4) Range Valve mount-ing capscrews and tighten to 21-27 lbs. in. (2.3-3.0 N m)using a cross pattern.
3. Reconnect the Transmission Harness to the Range Valveand close all air tanks drains.
Note: Install the Range harness back into the tie-down on theRange Valve.
IMPORTANT
8/13/2019 Servicio g3
44/94
41
Service Procedure
Air Filter/Regulator Removal
Special Instructions
The Air Filter/Regulator has two (2) o-rings located between the Air Filter/Regulator and the Range Cylinder Cover.
Special Tools
Basic Hand Tools
1. Air Filter Regulator2. Capscrew
2
1
8/13/2019 Servicio g3
45/94
42
Service Procedure
1. Relieve system air pressure by draining all air tanks onthe vehicle. Then, remove the vehicle air supply line fromthe Air Filter Regulator.
2. Using a 7/16 socket, remove the two (2) mounting cap-screws.
3. Remove the Air Filter/Regulator assembly.
Note: Be careful not to let the o-rings drop out of the RangeCylinder Cover when removing the Air Filter Regulator.
8/13/2019 Servicio g3
46/94
43
Service Procedure
Air Filter/Regulator Installation
Special Instructions
The Air Filter/Regulator has (2) o-rings located between the Air Filter/Regulator and the Range Cylinder Cover.
Special Tools
Basic Hand Tools
1. Air Filter Regulator2. Capscrew
2
1
8/13/2019 Servicio g3
47/94
44
Service Procedure
Lubricate o-rings with Eaton Fuller silicone #71214 orEquivalent.
1. If removed, press the two o-rings into the recesses in theRange Cylinder Cover.
Note: Apply Eaton Fuller sealant #71205 or equivalent to thetwo (2) mounting capscrews.
2. Using a 7/16 socket, install the two (2) mounting cap-screws and tighten to 8-12 lbs. ft. (11-16 N m).
Note: Hold the Air Filter Regulator flush with the Range Cylin-der Cover until its in place to prevent the o-rings fromdropping out.
3. Reinstall the vehicle air supply line to the Air Filter Regu-lator and close all air tank drains.IMPORTANT
8/13/2019 Servicio g3
48/94
45
Service Procedure
Inertia Brake Removal
Special Instructions
None
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Capscrew2. Inertia Brake3. Gasket
1. Capscrew2. Inertia Brake3. Gasket4. Spacer (Used on all Medium Duty ratios except the N)5. Gasket (Used on all Medium Duty ratios except the N)
1
2
3 5
4
3
2
1
8/13/2019 Servicio g3
49/94
46
Service Procedure
Heavy Duty Procedure1. Drain the lubricant from the transmission and disconnect
the Transmission Harness from the Inertia Brake Coil.
2. Using a 7/8 wrench, disconnect the Inertia Brake lubri-cant supply line from the transmission.
The Inertia Brake is heavy. Be prepared to handle theweight of the Inertia Brake when the mounting bolts areremoved.
3. Using a 9/16 socket, remove the six (6) mounting boltsfrom the Inertia Brake.
4. Remove the Inertia Brake and gasket from the transmis-sion.
Medium Duty Procedure1. Drain the lubrication from the transmission and discon-
nect the Transmission Harness from the Input Shaft
Speed Sensor and the Inertia Brake Coil.
2. Using a 3/8 wrench, remove the Input Shaft Speed Sen-sor.
WARNING
8/13/2019 Servicio g3
50/94
47
Service Procedure
3. Using a 7/8 wrench, remove the lubricant supply linefrom the transmission.
The Inertia Brake is heavy. Be prepared to handle theweight of the Inertia Brake when the mounting bolts areremoved.
4. Using a 9/16 wrench, remove the (6) mounting boltsfrom the Inertia Brake.
5. Remove the Inertia Brake, gaskets, and spacer (depend-ing on model) from the transmission.
Note: The Inertia Brake will contain some lubricant.
Note: The spacer and extra gasket are used on all transmis-
sion ratios except the N.
CAUTION
8/13/2019 Servicio g3
51/94
48
Service Procedure
Inertia Brake Installation
Special Instructions
None
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Capscrew2. Inertia Brake3. Gasket
1. Capscrew2. Inertia Brake3. Gasket4. Spacer (Used on all Medium Duty ratios except the N)5. Gasket (Used on all Medium Duty ratios except the N)
1
2
3 5
4
3
2
1
8/13/2019 Servicio g3
52/94
49
Service Procedure
Heavy Duty Procedure
The Inertia Brake is heavy. Be prepared to handle the
weight of the Inertia Brake until the mounting bolts areinstalled.
1. Clean and remove all old gasket material. Then, install theInertia Brake and new gasket, being careful to align theInertia Brake gear with the drive gear.
2. Using a 9/16 socket, install the six (6) mounting bolts.Tighten mounting bolts to 35-45 lbs. ft. (47-60 N m)using a cross pattern.
3. Using a 7/8 wrench, reconnect the Inertia Brake lubri-cant supply line to the transmission and tighten to 20-22lbs. ft. (27-29 N m).
4. Reconnect the Transmission Harness to the Inertia BrakeCoil.
Note: Fill the transmission with lubricant (see page 75).
WARNING
8/13/2019 Servicio g3
53/94
50
Service Procedure
Medium Duty Procedure
The Inertia Brake is heavy. Be prepared to handle the
weight of the Inertia Brake until the mounting bolts areinstalled.
1. Install the Inertia Brake, gaskets, and spacer (dependingon model) being careful to align the Inertia Brake gearwith the drive gear.
Note: The spacer and extra gasket are used on all transmis-sion ratios except the N.
2. Using a 9/16 socket, install the (6) mounting bolts.Tighten mounting bolts to 35-45 lbs. ft. (47-60 N m)using a cross pattern.
3. Using a 7/8 wrench, reconnect the Inertia Brake lubri-cant supply line to the transmission and tighten to 20-22lbs. ft. (27-29 N m).
4. Using a 3/8 wrench, install the Input Shaft Speed Sensorand tighten to 8-12 lbs. ft. (11-16 N m).
5. Reconnect the Transmission Harness to the Input ShaftSpeed Sensor and the Inertia Brake Coil.
Note: Fill the transmission with lubricant (see page 75).
WARNING
8/13/2019 Servicio g3
54/94
51
Service Procedure
Electric Shifter Removal
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Electric Shifter3. Gasket
1
2
3
8/13/2019 Servicio g3
55/94
52
Service Procedure
1. Remove nylon cable ties from the motor wires. Discon-nect the Transmission Harness from the Rail Select Sen-sor and the Gear Select Sensor.
2. Disconnect the Rail Select and Gear Select Motors fromthe Transmission ECU.
3. Using a 9/16 socket, remove the four (4) mounting cap-screws.
Possible Pinch Point - Make sure battery is disconnectedbefore removal of Electric Shifter.
4. Remove the Electric Shifter and gasket.
WARNING
8/13/2019 Servicio g3
56/94
53
Service Procedure
Electric Shifter Installation
Special Instructions
None
Special Tools
Basic Hand Tools
1. Capscrew2. Electric Shifter3. Gasket
1
2
3
8/13/2019 Servicio g3
57/94
54
Service Procedure
1. Check to ensure the shift blocks are in the neutral posi-tion, then move the shift finger to the center (neutral)location.
Note: If the shift finger is not properly aligned, the Electric
Shifter will not fit properly at its mounting location.
2. Clean and remove old gasket material from the Shift BarHousing. Then, install the new gasket on the Shift BarHousing.
Note: Apply Eaton sealant #71205 or equivalent to the mount-ing capscrews before installing.
3. The Dowel pin on the Electric Shifter must be alignedwith the hole in the Shift Bar Housing (used on 10 and 13& 18-Speed models only).
4. Position the Electric Shifter on the Shift Bar Housing.Then using a 9/16 socket, install the mounting cap-screws and tighten in a cross pattern as follows:
5, and 6-Speed (Aluminum Housing)- Tighten to 20-
25 lbs. ft. (27-33 N m).
10, 13, and 18-Speed (Cast Iron Housing) Tighten to34-45 lbs. ft. (45-60 N m).
5. Reconnect the Rail Select Sensor and Gear Select Sensor.
6. Reconnect the Transmission Harness to the Rail Selectand Gear Select motors. Using nylon ties, secure themotor wires to the transmission in their previous posi-tion.
8/13/2019 Servicio g3
58/94
55
Service Procedure
The Electric Shifter must be calibrated before the vehicle isplaced into operation.
7. To operate properly, the system must be calibrated as fol-lows:
Turn the ignition switch on and allow the transmis-sion to power up.
Turn the ignition switch to off and wait two minutes.
IMPORTANT
8/13/2019 Servicio g3
59/94
56
Service Procedure
Transmission Controller Removal
Special Instructions
None
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Nut2. Bracket3. Transmission ECU4. 38-Way Connectors5. Capscrew (Located inside 38-Way connectors)
1. Capscrew2. Transmission ECU3. 38-Way Connectors4. Capscrew (Located inside 38-Way connectors)
12 3
4
12
3
8/13/2019 Servicio g3
60/94
57
Service Procedure
Heavy Duty Procedure
The battery negative must be disconnected prior to unhook-ing the Transmission ECU 38-Way connectors.
Do not allow contamination into the Transmission ECU orconnectors.
1. Disconnect the following connectors:
Using a 5/32 allen wrench, unscrew and disconnectthe Transmission Harness 38-way connector andVehicle Interface 38-way connector.
2. Using a 7/16 socket, remove the three (3) mountingnuts.
3. Remove the Transmission Controller retaining bracket.
4. Remove the Transmission Controller assembly from thelocating studs.
CAUTION
8/13/2019 Servicio g3
61/94
58
Service Procedure
Medium Duty Procedure
The battery negative must be disconnected prior to unhook-ing the Transmission ECU 38-Way connectors.
Do not allow contamination into the Transmission ECU orconnectors.
1. Disconnect the following connectors:
Using a 5/32 allen wrench, unscrew and disconnectthe Transmission Harness 38-way connector andVehicle Interface 38-way connector.
2. Using a 7/16 socket, remove the three (3) mountingbolts.
3. Remove the Transmission Controller assembly from thelocating studs.
CAUTION
8/13/2019 Servicio g3
62/94
59
Service Procedure
Transmission Controller Installation
Special Instructions
Torques given below are in lbs. in.
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Nut2. Bracket3. Transmission ECU4. 38-Way Connectors
1. Capscrew2. Transmission ECU3. 38-Way Connectors
12 3
4
12
3
8/13/2019 Servicio g3
63/94
60
Service Procedure
Heavy Duty Procedure
Battery negative must remain disconnected until the Trans-mission ECU 38-Way connectors are installed.
Do not allow contamination into the Transmission ECU orconnectors.
1. Position the Transmission Controller on the locatingstuds.
2. Place the Transmission Controller retaining bracket overthe Transmission ECU.
3. Using a 7/16 socket, install the three (3) TransmissionController mounting nuts and tighten to 7 - 9 lbs. ft. (9.5 -12.2 Nm).
Do not exceed the torque on the Transmission Harness orVehicle Harness connector or bolt failure will occur.
4. Reconnect the following connectors:
Using a 5/32 wrench, reconnect the TransmissionHarness 38-way connector and tighten to 25 +/- 3lbs. in. (2.82 +/- .33 Nm).
Using a 5/32 wrench, reconnect the Vehicle Inter-face 38-way connector and tighten to 25 +/- 3 lbs. in.(2.82 +/- .33 Nm).
Reconnect the negative battery cable.
CAUTION
CAUTION
8/13/2019 Servicio g3
64/94
61
Service Procedure
The Electric Shifter must be calibrated before the vehicle isplaced in operation.
5. To operate properly, the system must be calibrated as fol-lows:
Turn the ignition switch on and allow the transmis-sion to power up.
Turn the ignition off and wait two minutes.
Medium Duty Procedure
Battery negative must remain disconnected until the Trans-
mission ECU 38-Way connectors are installed.
Do not allow contamination into the Transmission ECU orconnectors.
1. Position the Transmission Controller on the locatingstuds.
2. Using a 7/16 socket, install the three (3) TransmissionController mounting bolts and tighten to 7 - 9 lbs. ft. (9.5- 12.2 Nm).
Do not exceed the torque on the Transmission Harness or
Vehicle Harness connector or bolt failure will occur.
3. Reconnect the following connectors:
Using a 5/32 wrench, reconnect the TransmissionHarness 38-way connector and tighten to 25 +/- 3lbs. in. (2.82 +/- .33 Nm).
Using a 5/32 wrench, reconnect the Vehicle Inter-face 38-way connector and tighten to 25 +/- 3 lbs. in.(2.82 +/- .33 Nm).
Reconnect the negative battery cable.
The Electric Shifter must be calibrated before the vehicle isplaced in operation.
4. To operate properly, the system must be calibrated as fol-lows:
Turn the ignition switch on and allow the transmis-sion to power up.
Turn the ignition off and wait two minutes.
Note: UltraShift AW3- Perform clutch calibration: (seepage 75).
IMPORTANT
CAUTION
CAUTION
IMPORTANT
8/13/2019 Servicio g3
65/94
62
Service Procedure
Transmission Harness Removal
Special Instructions
None
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Transmission ECU 38-way connector2. Gear Sensor connector3. Rail Sensor connector4. 4-way Transmission Diagnostic connector
5. Input Shaft Speed Sensor connector6. Inertia Brake connector (DM3 models)7. Range Solenoid connector8. Output Shaft Speed Sensor connector9. Splitter Solenoid connector (13,18-speeds only)10. Mainshaft Speed Sensor connector11. Electric Shifter connector
1. Transmission ECU 38-way connector2. Gear Sensor connector3. Rail Sensor connector4. (Future position of 4-way Transmission Diagnostic connec-
tor5. Input Shaft Speed Sensor connector6. Inertia Brake connector7. WetClutch Solenoid connector (AW3 only)8. Output Shaft Speed Sensor connector9. Electric Shifter connector
1
2
3
45
6
7
8
9
10
11
1
2 3
5
4
6
7
8
9
8/13/2019 Servicio g3
66/94
63
Service Procedure
Heavy Duty Procedure
The battery negative must be disconnected prior to unhook-ing the Transmission ECU 38-Way connectors.
Do not allow contamination into the Transmission ECU orconnectors.
1. Disconnect the following connectors:
Using a 5/32 allen wrench, unscrew and disconnectthe Transmission Harness 38-way connector andVehicle Interface 38-way connector.
2. Disconnect the following harness connectors:
Inertia Brake Coil (if equipped)
Input Shaft Speed Sensor
Main Shaft Speed Sensor
Gear Select Sensor and Rail Select Sensor
Output Shaft Speed Sensor
Range and Splitter Valve Solenoids
4-Way Transmission Diagnostic connector
Electric Shifter [see page 1]
Medium Duty Procedure
The battery negative must be disconnected prior to unhook-ing the Transmission ECU 38-Way connectors.
Do not allow contamination into the Transmission ECU orconnectors.
1. Using a 5/32 allen wrench, disconnect the TransmissionHarness 38-way connector.
2. Disconnect the following harness connectors:
Inertia Brake Coil (if equipped)
Input Shaft Speed Sensor
Gear Select Sensor and Rail Select Sensor
WetClutch solenoid (AW3 only)
Output Shaft Speed sensor (location may vary)
4-way Transmission Diagnostic connector
Electric Shifter [see page 1]
CAUTION CAUTION
8/13/2019 Servicio g3
67/94
64
Service Procedure
Transmission Harness Installation
Special Instructions
None
Special Tools
Basic Hand Tools
Heavy Duty Medium Duty
1. Transmission ECU 38-way connector2. Gear Sensor connector3. Rail Sensor connector4. 4-way Transmission Diagnostic connector
5. Input Shaft Speed Sensor connector6. Inertia Brake connector (DM3 models)7. Range Solenoid connector8. Output Shaft Speed Sensor connector9. Splitter Solenoid connector (13,18-speeds only)10. Mainshaft Speed Sensor connector11. Electric Shifter connector
1. Transmission ECU 38-way connector2. Gear Sensor connector3. Rail Sensor connector4. (Future position of) 4-way Transmission Diagnostic connec-
tor5. Input Shaft Speed Sensor connector6. Inertia Brake connector7. WetClutch Solenoid connector (AW3 only)8. Output Shaft Speed Sensor connector9. Electric Shifter connector
1
2
3
45
6
7
8
9
10
11
1
2
3
5
4
6
7
8
9
8/13/2019 Servicio g3
68/94
65
Service Procedure
Heavy Duty Procedure
Do not allow contamination into the Transmission ECU con-
nectors.
Do not over tighten ty-raps.
You need to leave a service loop in the Transmission Har-ness.
Do not put sharp bends in the Transmission Harness.
The battery negative must be disconnected, while installingthe Transmission ECU connectors.
1. Reconnect the following harness connectors:
Gear Select and Rail Select Sensor
Main Shaft Speed Sensor
Input Shaft Speed Sensor
Inertia Brake Coil (if equipped)
Output Shaft Speed Sensor
4-way Transmission Diagnostic connector
Electric Shifter
Range and Splitter Valve Solenoids [see page 1]
Do not exceed the torque on the Transmission Harness orVehicle harness connector or bolt failure will occur.
Using a 5/32 allen wrench, reconnect the Transmission Har-ness 38-way connector and tighten to 25 +/- 3 lbs. in. (2.82 +/- .33 Nm).
Medium Duty Procedure
Do not allow contamination into the Transmission ECU con-nectors.
Do not over tighten ty-raps.
You need to leave a service loop in the Transmission Har-ness.
Do not put sharp bends in the Transmission Harness.
The battery negative must be disconnected, while installingthe Transmission ECU connectors.
1. Reconnect the following harness connectors: Gear Select and Rail Select Sensor
Input Shaft Speed Sensor
Inertia Brake Coil
Output Shaft Speed Sensor
4-way Transmission Diagnostic connector
Electric Shifter
WetClutch solenoid (AW3 only) [see page 1]
Do not exceed the torque on the Transmission Harness orVehicle harness connector or bolt failure will occur.
2. Using a 5/32 allen wrench, reconnect the TransmissionHarness 38-way connector and tighten to 25 +/- 3 lbs. in.(2.82 +/- .33 Nm).
CAUTION
CAUTION
CAUTION
CAUTION
8/13/2019 Servicio g3
69/94
66
Service Procedure
Shift Control Removal
Special Instructions
The exact location varies depending on vehicle manufacturer.
Special Tools
Basic Hand Tools
1. Nut
2. Washer3. Push Button Shift Control 30-Way Connector4. Backing Plate5. Push Button Shift Control
12
3
4
5
8/13/2019 Servicio g3
70/94
67
Service Procedure
1. Using a 1/4 socket, loosen the retaining bolt and discon-nect the 30-way connector from the back of the ShiftControl.
2. Using a 11/32 wrench, remove the two (2) nuts and lockwashers from the back of the Shift Control and removethe Shift Control.
Note: Shift Control location and use varies with each truck.
8/13/2019 Servicio g3
71/94
68
Service Procedure
Shift Control Installation
Special Instructions
Torques given below are in lbs. in.
Special Tools
Basic Hand Tools
1. Nut
2. Washer3. Push Button Shift Control 30-Way Connector4. Backing Plate5. Push Button Shift Control
12
3
4
5
8/13/2019 Servicio g3
72/94
69
Service Procedure
1. Install the Shift Control in its mounting location. Then,using a 11/32 wrench, install the two (2) lock washersand nuts and tighten to 14-16 lbs. in. (1.6-1.8 N m).
2. Using a 1/4 wrench, reconnect the 30-way connector tothe back of the Shift Control and tighten to 7.1 - 13.3 lbs.in. [0.8 - 1.5 N m]
8/13/2019 Servicio g3
73/94
70
Service Procedure
Cobra Lever Removal
Special Instructions
None
Special Tools
Basic Hand Tools
1. Tower2. Screw3. 8-Way Cobra Lever Harness Connector
1
2
3
4
8/13/2019 Servicio g3
74/94
71
Service Procedure
1. Using a phillips screwdriver remove the four screws fromthe Cobra Lever Housing.
2. Disconnect the 8-Way Cobra Lever harness connectorand remove the Cobra Lever from the Housing.
8/13/2019 Servicio g3
75/94
72
Service Procedure
Cobra Lever Installation
Special Instructions
None
Special Tools
Basic Hand Tools
1. Tower2. Screw3. 8-Way Cobra Lever Harness Connector
1
2
3
4
8/13/2019 Servicio g3
76/94
73
Service Procedure
1. Connect the 8-Way Cobra Lever harness connector andplace the Cobra Lever into the tower.
1. Using a phillips screwdriver install the four screws intothe Cobra Lever Housing.
8/13/2019 Servicio g3
77/94
74
Appendix
Operation
For more detailed information on transmission operation and shifting go to the Roadranger.com Literature Center(www.roadranger.com) and look for the drivers manual on your model transmission.
Generation III UltraShift - TRDR-0940
Generation III AutoShift - TRDR-0930
8/13/2019 Servicio g3
78/94
75
Appendix
Lubrication Specifications
5,6,10,13, and 18-Speed UltraShift DM3 and 10,18-Speed AutoShift
Never mix engine oils and synthetic transmission oils in the same transmission. When switching between types of lubri-cants, all areas of each affected component must be thoroughly drained.
Do not introduce additives and friction modifiers.
Do not mix lubricants of different grades.
Note: For a list of Eaton Approved Synthetic Lubricants, see TCMT-0021 or call 1-800-826-HELP (4357).
Note: The use of lubricants not meeting these requirements will affect warranty coverage.
Note: For lubrication change and inspection intervals see TCMT-0021.
Buy from a reputable dealerFor a complete list of approved and reputable dealers, write to: Eaton Corporation, Worldwide Marketing Services, P.O. Box 4013,Kalamazoo, MI 49003
Transmission Operating AnglesIf the transmission operating angle is more than 12 degrees, improper lubrication will occur. The operating angle is the transmis-sion mounting angle in the chassis plus the percent of upgrade (expressed in degrees). For operating angles over 12 degrees, thetransmission must be equipped with an oil pump or cooler kit to insure proper lubrication.
Operating Temperatures with Oil CoolersThe transmission must not be operated consistently at temperatures above 250 F. Operation at temperatures above 250F[121C] causes loaded gear tooth temperatures to exceed 350F [177C] which will ultimately destroy the heat treatment of thegears. If the elevated temperature is associated with an unusual operating condition that will reoccur, a cooler should be added,or the capacity of the existing cooling system increased.The following conditions in any combination can cause operating temperatures of over 250 F [121C]:
Operating consistently at slow speed.
High ambient temperatures.
Restricted air flow around transmission.
Use of engine retarder. High horsepower operation.
Note: Transmission coolers must be used to reduce the operating temperatures when the above conditions are encountered.
CAUTION
8/13/2019 Servicio g3
79/94
76
Appendix
Oil Cooler Chart
Transmission Oil Coolers are:
Recommended
With engines of 350 H.P. and above.
Required
With engines 399 H.P. and above and GCWs over 90,000 lbs.
With engines 399 H.P. and above and 1400 lbs. ft. or greater torque.
With engines 1500 lbs. ft. and above
18-speed AutoShift transmissions require use of an Eaton supplied oil-to-water cooler or approved equivalent.
With engines 450 H.P. and above.
8/13/2019 Servicio g3
80/94
77
Appendix
UltraShift ASW Models
Never mix engine oils and synthetic transmission oils in the same transmission. When switching between types of lubri-cants, all areas of each affected component must be thoroughly drained.
Do not introduce additives and friction modifiers.
Do not mix lubricants of different grades.
Note: For a list of Eaton Approved Synthetic Lubricants, see TCMT-0021 or call 1-800-826-HELP (4357).
Note: The use of lubricants not meeting these requirements will affect warranty coverage.
Note: For lubrication change and inspection intervals see TCMT-0021.
Buy from a reputable dealerFor a complete list of approved and reputable dealers, write to: Eaton Corporation, Worldwide Marketing Services, P.O. Box 4013,Kalamazoo, MI 49003
Synthetic Dextron III ATF
Synthetic Dextron III ATF must be used in the WetClutch portion of the transmission.
CD-50
CD-50 must be used in the gearbox portion of the transmission.
Maintenance/Lubricant Change Intervals
Transmission inspections and lubricant changes are outlined below.
For a list of Eaton Roadranger approved lubricants, order publication TCMT-0020.
Table 1: Lubricant Inspection and Change Interval (On-highway)
Interval Description
First 1,000 to 1,500 miles Inspect oil levels. Check for leaks.
Every 2,500 miles Inspect lubricant level. Perform Transmission Inspection.
Every 3 years or 150,000 miles, whichever oc-curs first
Change WetClutch oil and filters.
CAUTION
8/13/2019 Servicio g3
81/94
78
Appendix
Checking WetClutch Lubricant
The WetClutch portion is checked using a dipstick located in the engine compartment.
Proper WetClutch Lubricant Level
WetClutch lubricant level should be checked when idling in neutral, with the transmission temperature between 60 F and 120 F(15.5 C and 48.8 C) and when the vehicle has been idling in neutral for at least two (2) minutes. Proper lubricant level isobtained when the lubricant is between the cold ADD mark and the cold FULL marks on the dipstick. Due to thermal expansion ofthe lubricant, it is not recommended to check the level when the transmission is above 120 F (48.8 C).
Checking Gearbox Lubricant
The gearbox portion is checked at the lubricant fill plug located on the right side of the gear case.
Cooler
A transmission clutch cooler must be used with the Eaton UltraShift AW3 transmission. The cooler sizing must meet the require-ments specified in this TRIG-0930
Proper Gearbox Lubricant Level
The gearbox lubricant is at the proper level when it is even with bottom of the fill hole. When you remove the plug to check thelubricant level, lubricant should seep out. Do not use your finger to feel for the lubricant. Even if you can touch the lubricant, itmay not be at the proper level. In a transmission, one inch of lubricant level equals about one gallon of lubricant.
Actual Lube
LevelActual Lube
Level
8/13/2019 Servicio g3
82/94
79
Appendix
Drain the Transmission Gearbox and WetClutch Housing
1. Locate the drain plugs at the bottom of the transmission gear case and on the clutch housing oil pan.
2. Place a drain pan under each drain plug.
3. Remove both drain plugs and allow the lubricants to drain completely.
4. Disconnect both cooler lines at the WetClutch housing.
5. Pressurize one line with 20 PSI until all lubricant is forced out of the cooler.
6. Reconnect both cooler lines.
Change WetClutch Filters
Change the lubricant filters when the transmission lubricant is changed. Detailed information can be found on removal andreplacement of the oil filters in this service manual.
Fill the Transmission
1. Install the transmission gearbox drain plug and tighten to 45-55 lbs. ft. (60-73 Nm). Sealant is not required on thedrain plug threads.
2. Install the clutch housing oil pan drain plug and torque to 34-48 lbs. ft. (45-64 Nm). Sealant is not required on thedrain plug thread.
3. Fill the transmission gearbox with the recommended lubricant until the lubricant seeps out of the fill hole.
4. Install the fill plug and torque to 25-35 lbs. ft. (33-47 Nm).
5. Slowly fill the clutch through the dipstick tube with an initial fill of 18 pints (8.5 liters) of the recommended lubricant.
6. Place the transmission in neutral position apply the parking brakes. Start the engine and let idle for five (5) minutes,
(this allows oil to fill the WetClutch system and cooling system), add oil as needed to obtain a level at the proper tem-perature range. Total oil quantity at this time varies depending on the cooling system capacity.
7. Increase the engine idle slowly to 1500 RPM for two (2) minutes. Now, recheck the oil level at normal idle speed in neu-tral, again adding oil to obtain a level at the proper temperature range.
8. Install the dipstick and tighten securely.
8/13/2019 Servicio g3
83/94
80
Appendix
Clutch Calibration
The ASW system automatically provides for clutch wear. The system will initiate a clutch calibration once per vehicle power up,when certain vehicle conditions are right. Of these conditions, the most important ones include: when the engine is running atidle speed, during normal operating temperature, when the vehicle is stopped, and when neutral is selected on the Shift Control.During the calibration, the clutch is partially engaged until the engine begins to slightly lug down. It will then disengage the clutchand repeat this process several times. The calibration process usually takes as little as thirty seconds but can take as long astwo(2) minutes. The calibration will be aborted when any position other than neutral is selected on the Shift Control.
If it appears that the vehicle is not engaging smoothly from a stop, it is possible that the clutch needs to be re-calibrated. If it hasnot been previously calibrated during the current power up, stop the vehicle with the engine idling at its normal operating tem-perature and place the Shift Control in neutral and wait two(2) minutes. If the calibration is being performed you should hear theengine slightly lug down and then return to its no load condition several times.
If calibration does not occur a Power Down/Power Up will initiate a calibration.
8/13/2019 Servicio g3
84/94
Appendix
Inspection Procedures
For all inspection procedures on assembly and disassembly refer to the service manual covering the base box procedures. Thesemanuals can be found on roadranger.com under the Literature Center.
8/13/2019 Servicio g3
85/94
82
Appendix
Basic Troubleshooting
For all Basic Troubleshooting questions refer to the appropriate service manual covering the base box procedures. These manu-als can be found on roadranger.com under the Literature Center.
8/13/2019 Servicio g3
86/94
83
Appendix
Air System Operation and Troubleshooting
For all air system operation and troubleshooting questions refer to the "Gen III Troubleshooting Guide" TRTS-0930, which is foundon Roadranger.com under the Literature Center.
8/13/2019 Servicio g3
87/94
84
Appendix
Tool Specifications
General Tools
The following General Tools are available from several tool manufacturers such as Snap-On, OTC, and many others.
Table 5 General Tools
TOOL PURPOSE
0 - 100 lbs. ft. (0-135 Nm) 1/2" (12.7mm) drive TorqueWrench
General torquing of fasteners (Typically 15-80 lbs. ft. (20-108Nm))
0 - 600 lbs. ft. (0-810 Nm) 3/4" or 1" (19mm or 25.4mm)drive Torque Wrench
Torquing of Output Nut
0 - 50 lb. in. (0-5.62 Nm) 3/8" (9.52mm) drive TorqueWrench
General torquing of fasteners
2 3/4" (70mm) or Socket - Standard Depth To remove the Output Yoke/Flange NutLarge Brass Drift 3/4" x 12" (19mm x 304.8mm) Used to protect shafts and bearings during removal
Large Dead Blow Hammer or Maul 32 ounces To provide force for shaft and bearing removal
(2) Air Pressure Gauges (0-150 PSI) 0-10.34 BAR To troubleshoot and verify correct operation of air system
3/8" Drive Deepwell socket set 3/8"- 1" (9.5mm - 25.4mm) To remove/install capscrews and nuts
3/8" Drive Shallow socket set 3/8" - 1" (9.5mm - 25.4mm) To remove/install capscrews and nuts
Snap Ring Pliers - Large Standard External To remove the snap rings at the auxiliary drive gear, input shaftbearing, and countershaft bearings
Feeler Gauges To set mainshaft washer endplay and auxiliary tapered bearingendplay
Open-end wrench set 3/8" - 1" (9.52mm -25.4mm) To remove certain airline connections
8/13/2019 Servicio g3
88/94
85
Appendix
Torque Specifications
Correct torque application is extremely important to assure long transmission life and dependable performance. Overtighteningor under-tightening can result in a loose installation and, in many instances, eventually cause damage to transmission gears,shafts or bearings. Use of a thread sealer/locking compound is recommended for all capscrews. Do not torque capscrews dry.
Description Torque Valuelbs. ft. [Nm]
Thread size Additional Comments
Transmission-to-Engine capscrews Refer to OEMfor specification
Clutch-to-Flywheel capscrews
7/16 x 2.25 x 14 40 - 50 lbs. ft.[54 - 68 Nm]
7/16 x 2.25 x 14 40 - 50 lbs. ft. [54 - 68 Nm]
3/8 x 2.25 x 16 30 - 35 lbs. ft.[41 - 47 Nm]
3/8 x 2.25 x 16 30 - 35 lbs. ft. [41 - 47 Nm]
M10 x 1-3/8 26 - 35 lbs. ft.[35 - 47 Nm]
M10 x 1-3/8 26 - 35 lbs. ft. [35 - 47 Nm]
M10 x 1-3/4 26 - 35 lbs. ft.[35 - 47 Nm]
M10 x 1-3/4 26 - 35 lbs. ft. [35 - 47 Nm]
6 (Small PTO Cover Capscrews) 20 - 25 lbs. ft.[27 - 34 Nm]
3/8"-16 Apply Loctite 242 to threads.
8 (Large PTO Cover Capscrews) 50 - 65 lbs. ft.[68 - 88 Nm]
7/16"-14 Apply Loctite 242 to threads.
4 Electric Shifter Capscrews 30 - 45 lbs. ft.[48 - 61 Nm]cast and 20 - 25
lbs. ft. [27 - 34Nm] aluminum
3/8" - 16
1 Reverse switch 20 - 25 lbs. ft.[27 - 34 Nm]
9/16"-18
1 Neutral switch/cap 20 - 25 lbs. ft.[27 - 34 Nm]
3/4"-16
3 ECU Capscrews (Medium Duty) 7 - 9 lbs. ft. (9.5- 12.2 Nm)
1/4" - 20 3 ECU Nuts (Heavy Duty) 7 - 9 lbs. ft. [9.5
- 12.2 Nm]1/4" - 20
2 Transmission ECU 38-Way Connectors Cap-screws
25 +/- 3 lbs. in.[2.82 +/- .33Nm]
M5 - .8
3 ECU Bracket Nuts 20 - 25 lbs. ft.[27 - 34 Nm]
.3125" - 18
3 ECU Bracket Studs 35 - 45 lbs. ft.[48 - 61 Nm]
3/8" - 16
2 Harness Bracket Capscrews 20-25 lbs. ft.[27-34 Nm]
.3125-18
8/13/2019 Servicio g3
89/94
86
Appendix
1 Push Button Shift Controller 30-Way Connec-tor Capscrew
10 +/- 3 lbs. in.[14 +/- 4 N m]
2 Push Button Shift Controller Backing Platenuts and lockwashers
14-16 lbs. in.[1.6-1.8 N m]
6 Inertia Brake Capscrews 40-45 lbs. ft.[54- 61.0 Nm]
3/8"-16 Apply Loctite 242 to threads.
2 Inertia Brake Hose Fittings 30-40 lbs. ft.[41-54 Nm]
3/4"-16
4 Splitter Solenoid Capscrews 21-27 lbs. in.[2.4-3.1 Nm]
#10-24
4 Range Solenoid Capscrews 21-27 lbs. in.[2.4-3.1 Nm]
#10-24
1 Output Shaft Speed Sensor Capscrew (MD) 8-10 lbs. ft.[10.8-13.6
Nm]
1/4"-20
1 Main Shaft Speed Sensor Capscrew 8-10 lbs. ft.[10.8-13.6Nm]
1/4"-20
1 Input Shaft Speed Sensor Capscrew 8-10 lbs. ft.[10.8-13.6Nm]
1/4"-20
2 Rail Sensor Capscrews 21-27 lbs. in.[2.4-3.1 Nm]
2 Gear Sensor Capscrews 21-27 lbs. in.[2.4-3.1 Nm]
2 Air Filter Regulator Capscrews 8-12 lbs. ft.[10.8-16.02Nm]
1/4"-20 Apply Loctite 242 to threads.
1 Lubricant fill plug (6-Speed) 45 - 55 lbs. ft.[61 - 75 Nm]
3/4-NPT
1 Lubricant fill plug (13,10,18-speed) 60 - 75 lbs. ft.[47 - 61 Nm]
1-NPT
2 Lifting Bracket Capscrews 35 - 45 lbs. ft.[47 - 61 Nm]
3/8"-16
Transmission Nodal Mount Capscrews
(10,13,18-Speed)
Refer to OEM
for Specification2 Transmission Rear Mount Nuts (10,13,18-Speed)
Refer to OEMfor Specification
6 - Speed AW3 Specific
Oil cooler line fitting 50 - 60 lbs. ft.[68 - 81 Nm]
Oil cooler line nut 50 - 60 lbs. ft.[68 - 81 Nm]
8/13/2019 Servicio g3
90/94
87
Appendix
2 Dipstick tube fitting 60 - 70 lbs. ft.[81 - 95 Nm]
1 5/8"-12
1 WetClutch drain plug 34 - 48 lbs. ft.[46 - 65 Nm]
12 Flywheel to Drive Coupler Capscrews 3/8 x 16 x 1-1/4 35 - 40 lbs. ft.[47 - 55 Nm]
High Pressure Oil Filter 25 - 35 lbs. ft.[34-41 Nm]
Low Pressure Oil Filter Turn until seal touches, then tighten witha 1/2" drive 3/4 to 1 full turn.
8/13/2019 Servicio g3
91/94
88
Appendix
Torque Overview
Heavy Duty
Air Filter Requlator
Range Valve Solenoid
Rail SelectSensor Capscrews
Gear SelectSensor Capscrews
Electric ShifterCapscrews
Input ShaftSpeed Sensor Capscrew
Main ShaftSpeed Sensor Capscrew
Splitter ValveSolenoid Capscrew
Output ShaftSpeed Sensor Capscrew
Transmission ECU Nuts
Inertia Brake Capscrews
ECU BracketNuts & Studs
8/13/2019 Servicio g3
92/94
89
Appendix
Medium Duty
Electric Shifter Capscrews
Gear Select
Sensor Capscrews
Rail SelectSensor Capscrews
Output ShaftSpeed Sensor Capscrew
Transmission ECU Nuts
Inertia Brake CapscrewsOil Pan Capscrews
Oil Pan Drain Plug
Input ShaftSpeed Sensor Capscrew
8/13/2019 Servicio g3
93/94
8/13/2019 Servicio g3
94/94