Service Training This training will cover both HWF5300 and HWF5000 Models

HWF5300 - HWF5000FRONT LOAD WASHER

Service TrainingThis training will cover both

HWF5300 and HWF5000 Models.The main variations between the models are the control panel options and related parts.

Options including spin speed will vary between models

The HWF5300 is electronic touch control

The HWF5000 is electronic dial and button control


Model information

H W F 5300 A W

Haier

Washer

Front loadA edition*Color W = White

*Very important when ordering parts


Serial number explanation*

CE0H50E0100 C R 9A9 0001

Product code

laundry

Product lineDate of manufacture

Date of manufacture:

9 A 9

YearMonth

Date

First code Second code Third code

Year Code Month Code Day Code

2000 0Jan 1 1 1Feb 2 2 2

2001 1Mar 3 3 3Apr 4 4 4

2002 2May 5 5 5Jun 6 6 6

2003 3Jul 7 7 7Aug 8 8 8

2004 4Sep 9 9 9Oct A 10 A

2005 5Nov B 11 BDec C 12 C

2006 613 D

14 E

2007 715 F

16 G

2008 817 H

18 J

2009 919 K

20 L

21 M

22 N

23 P

24 Q

25 R

26 S

27 T

28 U

29 V

30 W

31 Ｘ

* Does not apply to all product lines


Front Components


! ! ! Drain Height ! ! !

96” maximum

30” minimum


2. Net dimension


Product specification HWF5300

4 Cu. Ft. 1300 RPM Energy Star Washer – Freestanding

• LED Touch Pad Electronic Control with Indicator lights

• Stainless Steel Drum

• 12 Cycle Selection

• Sanitary Cycle with built in water heater

• 6 Wash / Spin speed Combinations

• 3 Soil Level Selections

• 6 Water Temperature Selections

• Self Clean lint filter

• Child Lock

• End of cycle Signal and Cycle Error Signal

• Anti-Microbial Treated Door Gasket

• Variable Speed Motor

• Drum Light

• Bleach, Fabric Softener, Prewash and Detergent Dispenser


Product specification HWF5000

4 Cu. Ft. 1000 RPM Energy Star Washer – Freestanding

• LED Electronic Display with Dial and indicator lights

• Stainless Steel Drum

• 10 Cycle Selection

• 4 Wash / Spin speed Combinations

• 3 Soil Level Selections

• 4 Water Temperature Selections

• Self Clean lint filter

• Child Lock

• End of cycle Signal and Cycle Error Signal

• Anti-Microbial Treated Door Gasket

• Variable Speed Motor

• Bleach, Fabric Softener, Prewash and

• Detergent Dispenser


Control panel HWF5300A

B C D E F G H I J

K

L

M

N O P

A. PowerB. Start/PauseC. Soil levelD. Rinse levelE. Spin speed

F. Water tempG. BeeperH. Extended SpinI. Stain TreatJ. Rinse &/SpinK. Prewash

M. DelayL. Custom programN. LED Display ZoneO. Child lockP. Door lock LED


Error Codes

Error Code DisplayFor

HWF5300

Error Code DisplayFor

HWF5000

Check Haier America Parts and Service web site for latest information






Tachometer


Tachometer



Lock winding

Unlock winding

SharedMicroswitch






Self test HWF5300





Wiring circuit – HWF5300


Shipping Brackets4 Shipping brackets MUST be removed

and kept for future moves


Detergent Dispenser

Press down tab to remove dispenser

! Use HE detergent ONLY !


Remove 2 screws

Top Cover Removal

Slide Cover Backto release locks

NOTE – Front panelUses same locking

system


5 screws Release the wiring harness4 screws

Control Panel Removal

Push locking tabs down across top while

pulling out at bottom


CONTROL PANEL DISSASSEMBLY

Remove wire harness

Remove screws and clips

Access to Touch Pad Assembly


Door Lock Removal

Open door and remove 3 screws

EMERGENCY PROCEDURE

! ! ! If door latch is jammed: ! ! ! Remove top coverPull down on tabPull door open

Remove wiring then remove switch

Remove top cover

See ERROR CODES Section for testing


Control Board and Water Level Switch

Water inlet valves

Wires MUST be on proper solinoid for proper operation

Connectors are color coded

See ERROR CODES Section for troubleshooting


Drain pump

Drain water using waste water pipe

Remove screws and push drain pipe through cover


Disconnect wiring and plumbing

Drain pump

Remove screws behind filter coverThen tilt unit back

! ! ! Bottom Cover Removed ! ! !

Remove Screws from bottom panel


Dispenser – Water Inlet

Remove dispenser tray and mounting screws

. Disconnect hosesMark if necessary for proper replacement


Door Glass, Hinge and Latch

Open door and remove hinge screws

removerubber

covers and screws

Remove outer coverNote alignment groove


Door Boot / Seal

Spring loaded retainer ringS-hooks at each end of spring

With retainer ring removed fold gasket inward to remove

Rear of seal is held in place with screw type clamp ring


Arrow and Notch shouldbe in alignment

(arrow is behind counterweight)

Drain Holesmust be at the

bottom

! ! ! CRITICAL INSTALLATION INFORMATION ! ! !Door Boot / Seal


Shock Absorbers Front Shock Absorbers

Remove the control panel and door boot as shown earlier.

release the screws on the front corner.

Remove screws from top of front panel (2)

and pump housing

Lift top up and off of retaining clips


Shock Absorbers

When replacing the pins put a small amount of grease on the

pin to prevent noise

Use pliers to hold the raised end, then push the pin toward the back

Remove

Replace pins pushing in from the back


Belt Replacement

! ! ! NOTICE ! ! !PINCH HAZARD

There is no adjustment for the belt. A loose or worn belt must be replaced.

Do not fold, kink or sharply bend this belt.

--To remove the belt-- ‘Roll’ the upper pulley while pulling

the belt towards you.

--To install--Place the belt under the motor pulley then ‘roll’

the upper pulley and pull the belt into place.


Motor Replacement

Motor is easily accessed through back panel

Remove belt then wiring harness and 2 screws. Motor will pull forward off of rear bushings

BoltsWiring Harness


Heater Replacement

Heater and sensor is easily accessed through back panel.

See trouble shooting section for specs and error codes.

Nut DO NOT OVER TIGHTEN

To remove the heater assembly:

Loosen but DO NOT remove the nut.

Tap the end of the stud with a plastic driver to release the squeeze bushing.

Pull the heater out

ReplacementInsert the heater making certain it is

placed with bend down and enters the retainer

Tighten nut till you see the seal starting to puff out around flange

Drum DOES NOT have to be split

to replace heater


Bearing and SealSee Haier America Parts and Service Website for latest information

* Remove control panel and front cover

* Remove mounting screws from dispenser housing

* Remove counter weights (mark location before removing)

* Remove drain and fill hoses

* Remove motor

* Remove shock absorbers – be careful to fully support tub

* Carefully lift outer drum and remove through front opening


Bearing and SealSee Haier America Parts and Service Website for latest information

Drum Assembly with boot and drain attached

25 screws around center of drum split the halves. Use care when reassembling – do

not over-tighten. Watch that the O-ring seal is in place between halves.

Rear main seal and heater

















Documents

Service Training This training will cover both HWF5300 and HWF5000 Models