Service Manuals LG TV PLASMA 50PM1MA 50PM1MA Service Manual

PLASMA MONITORSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : RF-052A

MODEL : 50PM1M/MA/MB50PM1M/MA/MB-TA

website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html

- 2 -

CONTENTS

SAFETY PRECAUTIONS ....................................................................................3

DESCRIPTION OF CONTROLS ..........................................................................4

SPECIFICATIONS................................................................................................9

ADJUSTMENT INSTRUCTIONS .......................................................................11

TROUBLE SHOOTING GUIDE..........................................................................16

PRINTED CIRCUIT BOARD ..............................................................................25

BLOCK DIAGRAM.............................................................................................27

EXPLODED VIEW..............................................................................................30

EXPLODED VIEW PARTS LIST ........................................................................31

REPLACEMENT PARTS LIST...........................................................................32

SCHEMATIC DIAGRAM.........................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.

When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument’sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

POWERMUTE

INPUT MULTIMEDIA

ARC MENU

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM SLEEP

REVEAL MODE

MIXSIZE

UPDATE TIMEQ.VIEW

HOLD INDEX

?

i

I/II

TEXT/

LIST/

MULTIMEDIAselects the Component, RGB or

HDMI modes.

POWERswitches the set on from standby oroff to standby.

ARC changes the picture format.

MENUdisplays on screen menus one by one.exits the current menu.memorizes menu changes.

SSMto select the sound appropriate toyour viewing programme character.

NUMBER buttons

SLEEPsets the sleep timer.

I/II (option)selects the language during dual lan-guage broadcast.selects the sound output.

TEXT/* (option)These buttons are used for teletext.For further details, see the ‘Teletext’section.COLOURED BUTTONS :These buttons are used for teletext.

LIST (option)displays the programme table.

INPUT

MUTEswitches the sound on or off.

DD / EESelects a menu option.

FF / GG (Volume Up/Down)Increases/decreases sound level.

Adjusts menu settings.OK

accepts your selection or displays thecurrent mode.

PSMadjusts the factory preset picture

according to the room.

SPLIT ZOOMenlarge the screen with regular

ration.

Q.VIEW (option)Returns to the previously viewed

programme.Note : This function works only when

Favourite prog. is set to Off .Otherwise each press of this button

will select a stored favorite programme.

- 4 -

DESCRIPTION OF CONTROLS

- 5 -

<Front Panel Controls>

42PM1MA/J series / 50PM1MA/J series

ON/OFF

1. Main Power Button

2. Remote Control Sensor

3. Power Standby IndicatorIlluminates red in standby mode, Illuminates green when theset is turned on

4. INPUT SELECT Button

5. MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.

6. DD / EESelects a menu option.FF / GG (Volume Up/Down)Increases/decreases sound level.Adjusts menu settings.

1

4

5

6

3 2

- 6 -

<Back Panel>

AC INPUT

AUDIO INPUT RGB INPUT

RGB OUTPUT

RS-232C INPUT(CONTROL/SERVICE)

REMOTECONTROL

S-VIDEO

Y PB PR

VIDEO

R L

VARIABLE AUDIO OUT

AUDIOR L

EXTERNAL SPEAKER HDMI/DVI(VIDEO) INPUT

R L

AUDIO

R L

AUDIO

R L

AUDIO VIDEO

COMPONENT INPUT 2

COMPONENT INPUT 1

MONITOR OUPUT

A/V INPUT(MONO) (MONO)

Antenna

Connection to PC Connection to AV equipment

- 7 -

<Back Panel>

AC INPUT


RGB OUTPUT


REMOTECONTROL

Y PB PR

VIDEOS-VIDEO

R L

VARIABLE AUDIO OUT

AUDIOR L


L R

VIDEO AUDIO

COMPONENT INPUT

AV3(MONO) AV1 AV2

AV1AV1

Antenna

RCA Type

Scart Type

4

AC INPUT


RGB OUTPUT


REMOTECONTROL

S-VIDEO

Y PB PR

VIDEO

R L

VARIABLE AUDIO OUT

AUDIOR L


R L

AUDIO

R L

AUDIO

R L

AUDIO VIDEO

COMPONENT INPUT 2

COMPONENT INPUT 1

MONITOR OUPUT

A/V INPUT(MONO) (MONO)

Antenna

1 2 3 4 5

1. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.

2. HDMI/DVI (VIDEO) / AUDIO INPUT / RGB INPUT SOCKETSConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.Note: If you want to use RGB/DVI audio, we strongly recom-mend that you use the cable that has a core, or the EMI Filtercore along with separate cable.

RGB OUTPUT SOCKETYou can watch the RGB signal on another set, connect RGBOUTPUT to another monitor’s PC input port.

REMOTE CONTROL

VARIABLE AUDIO OUTPUT

3. EXTERNAL SPEAKER OUTPUT (8 ohm)Connect to optional external speaker(s).* For further information, refer to ‘Speaker & Speaker Stand’

manual.

4. COMPONENT / AUDIO INPUT SOCKETSS-VIDEO / AUDIO (L/MONO) INPUT SOCKETSVIDEO / AUDIO (L/MONO) INPUT SOCKETS

ANTENNA INPUT

EURO SCART SOCKETConnect the euro scart socket of the VCR to these sockets.Note: a. If you want to use the EURO scart cable, you have to usethe signal shielded Euro scart cable.b. If you want to use your external hi-fi stereo system, turn offthe internal speakers of the set.

5. POWER CORD SOCKETThis set operates on an AC power. The voltage is indicated onthe Specifications page. Never attempt to operate the set onDC power.

- 8 -

AS mark

LG TV

Owner’s Manual

1.5V1.5V

Alkaline batteriesPower Cord

POWERMUTE

INPUT MULTIMEDIA

ARC MENU

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM SLEEP

REVEAL MODE

MIXSIZE

UPDATE TIMEQ.VIEW

HOLD INDEX

?

i

I/II

TEXT/

LIST/

Remote Control handset

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.

- Contract your dealer for buying these items.

Optional Extras

Accessories

Tilt wall mounting bracket

404250 40 42 50

Video cables Audio cables

Ceiling mounting bracket

40

4250

42

40

Desktop stand

Speakers

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

- 9 -

V Application RangeThis spec is applied to the PDP TV used RF-052A Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 25±5°C (77±9°F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety: IEC60065EMI : CISPR13

V General Specification

1. Module Specification

Remark

PDP

LGE SPEC

Maker : SONY/ LGIT/ Sanken

Specification

50 inch wide Color Display Module

16:9

PDP50X3,

RGB Closed Type

1) Temp : 0~40 deg

2) Humidity : 0~85%

1) Temp : -20~60 deg

2) Humidity : 0~85%

100-240V~, 50/60Hz

No

1

2

3

4

5

6

Item

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

2. Model Specification

- 10 -

Item

Market

Broadcasting system

Available Channel

Receiving system

Video Input (1EA)

Video Output(1EA)

S-Video Input(1EA)

Component Input(2EA)

RGB Input

RGB Output

HDMI Input(1EA)

Audio Input(5EA)

Audio Input(1EA)

Audio Output(3EA)

Audio Output(2EA)

Wired Control

No

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Specification

Non-EU

PAL B/G/I/D/K, NTSC

BAND PAL

VHF E2~E12

UHF E21~E69

CATV S1~S47

HYPER S1~S20

Upper Heterodyne

PAL, SECAM, NTSC

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC, RGB-DTV

RGB-PC, RGB-DTV

HDMI-PC, HDMI-DTV

PC Audio, Component(2EA),

AV(1EA), S-audio(1EA)

PC Audio

AV(1EA), External audio out(1EA),

Variable Audio out(1EA)

External audio out(1EA)

Variable Audio out(1EA)

Discrete IR

Remark

Except 42PM1MB, 50PM1MB, 42PM3MVB



42PM1M, 42PM1MA, 50PM1M, 50PM1MA

42PM3MV, 42PM3MVA

42PM1MB, 50PM1MB, 42PM3MVB

42PM1M, 42PM1MA, 50PM1M, 50PM1MA,

42PM3MV, 42PM3MVA

42PM1MB, 50PM1MB, 42PM3MVB

- 11 -

ADJUSTMENT INSTRUCTIONS

1. Application ObjectThese instructions is applied all of the PDP TV, RF-052AChassis.

2. Specification(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100-220V,50/60Hz.

(5) The receiver must be operated for about 15 minutes priorto the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.

O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full White pattern.

[ Set is activated HEAT-RUN without signal generator inthis mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes,(Especially digital pattern, cross hatch pattern) afterimage may be occur in the black level part of the screen.

3. Channel memory

3-1. Setting up the LGIDS1) Install the LGIDS. (idsinst.exe)2) After installation, restart your PC.3) Extract [files.zip] to folder [c:\LGIDS\files].4) Start LGIDS.

3-2. Channel memory Method 1) Select “PDP” and “Hurricane” on Model dialog. And check

your connection in Communication dialog. (If yourconnection is ‘NG’, then set your PORT(COM1,2,3,...)correctly.)

2) Connect RS-232C cable and turn on the power.(If your connection has completed, you can see “Ready”.)

[ If your set is not an end products but only a board, youhave to make your board to Stand-by state (LED_R). Andyou have to Download in Stand_by power state.

3) Select proper CH_memory file(*.nvm) for each model at[NVRAM Download] $ [Write Batch]Next, select proper binary file(*.bin) including the CHinformation for each model at [NVRAM File].

4) Click the [Download] button.It means the completion of the CH memory download if allitems show ‘OK’ and Status is changed by ‘PASS’ at thelower right corner of the window.

5) If you want to check whether the CH information ismemorized correctly or not, click the [Verify] button. And then compare NVRAM File(*.bin) with the CHinformation downloaded.

(Fig. 1)

(Fig. 2-1)

(Fig. 2-2)

- 12 -

4. POWER PCB Assy V oltageAdjustments (Va, Vs Voltage Adjustments)

4-1. Test Equipment : D.M.M. 1EA

4-2.Connection Diagram for Measuring: refer to fig.3

4-3. Adjustment Method[P/No 3501V00221A B/D]

(1) Va Adjustment1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D.M.M to Va pin of P805, connect

- terminal to GND pin of P805.3) After turning RV601, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

(2) Vs Adjustment1) Connect + terminal of D.M.M to Vs pin of P805, connect

– terminal to GND pin of P805.2) After turning RV401, voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(Deviation; ±0.5V)

5. EDID (The Extended DisplayIdentification Data)/ DDC (DisplayData Channel) download

5-1. Required T est Equipment1) Adjusting PC with S/W for writing EDID Data.(S/W : EDID

TESTER Ver.2.5)2) A Jig for EDID Download3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable

5-2. Setting of device

5-3. Preparation for Adjustment1) As above Fig. 5, Connect the Set, EDID Download Jig, PC

& Cable.2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver,2.53) Set up S/W option

Repeat Number : 5Device Address : A0PageByte : 8

4) Power on the Set

5-4. Sequence of Adjustment

(1) DDC data of Analog-RGB1) Init the data

2) Load the EDID data.(Open File)[Analog-RGB : MF056A_RGB.ANA][digital(HDMI) : MF056A_DMI.DVI]

3) Set the S/W as below.4) Push the “Write Data & Verify”button. And confirm “Yes”.5) If the writing is finished, you will see the “OK” message.

Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)

Va ADJRV601

P806

P805

P807

Va

GNDNCVS

DMM

+ - P804

P801 P802

Vs ADJRV401

P803

(Fig. 3) Connection diagram of power adjustment for measuring

(Fig. 4) Connection Diagram of DDC download

- 13 -

6. Auto A V(CVBS) Color Balance

6-1. Requirement- This AV color balance adjustment should be performedbefore white Balance Adjustment

6-2. Required Equipment1) Remote controller for adjustment2) AV Pattern Generator

: 802F Pattern Generator, Master(MSPG-925FA), etc(Which has PAL Composite Video format output withstandard(1.0 Vpp) Vertical 100% Color Bar Pattern as Fig6)

6-3. Method of Auto A V(CVBS) Color Balance1) Input the PAL Composite Video (Fig6. 100% Color Bar

Pattern) into video input.(RCA : AV1, SCART : AV3 Input, PAL : 50Hz, NTSC : 60Hz)

2) Set the PSM to Standard mode in Picture menu.3) Press INSTAR key on R/C for adjustment.4) Press the G(Vol. +) key operate to set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

7. Adjustment of White Balance

7-1. Required Equipment1) Remote controller for adjustment2) Color Analyzer (CA-100 or same product)3) Auto W/B adjustment instrument(only for Auto adjustment)4) AV Pattern Generator

7-2. Connecting diagram of equipment formeasuring (For Auto Adjustment)

W Auto adjustment Map(RS-232C)

7-3. Adjustment of White Balance(For Manual adjustment)

O Operate the zero-calibration of the CA-100, then sticksensor to PDP module surface when you adjust.

O For manual adjustment, it is also possible by the followingsequence.

1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operate heatrun more than 15 minutes.

2) As below Fig.8, Supply 216Level (85 IRE) full screenpattern to Video input.(RCA : AV1, SCART, AV3 Input, PAL : 50Hz, NTSC: 60Hz)

3) Press the TV/AV KEY on R/C for converting input mode.4) Set the PSM to Standard mode in Picture menu.5) Enter the White Balance adjustment mode by pressing the

INSTART key twice(White Balance) on R/C.

(Fig. 6) Auto AV(CVBS) Color Balance Test Pattern

216 Level (85 IRE)

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j a

j b

j c

j d

j e

j f

Stop bit

1

Parity

NONE

RF-052A/B/C

ProtocolSetting

Data Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

(Fig. 7) Connection Diagram of Auto W/B Adjustment

MSPG-2100 /MSTG- 5200

216 Level (85 IRE)

COLORANALYZERTYPE ; CA-100

CVBSsignalinput

RS-232C Serial Communication

(Fig.5) EDID DATA

- 14 -

6) Stick sensor to center of the screen and select each items(Red/Green/Blue Gain and offset) using D / E(CH +/-) keyon R/C.

7) Adjust Only High Light with R Gain/ B Gain using F / G(VOL+/-) key on R/C.

8) Adjust it until color coordination becomes as below.(Initially, R/G/B gain and R/G/B offset values are fixedRed Gain : 82, Green Gain : 80, Blue Gain : 86Red Offset : 7D, Green Offset : 7E, Blue Offset : 80)(High Light G Gain : 7A // Low Light R Offset : 7F, G Offset7E, B Offset 80 is Fixed)Bright : High Light : 80 ± 20cdColor-Coordinate : High Light : X : 0.285 ± 0.003

Y : 0.295 ± 0.003Color Temperature : 9,300°K ± 500°K

9) When adjustment is completed, Exit adjustment mode usingEXIT key on R/C

8. Auto Component Color Balance[Requirement]It is very import to use correct adjustment pattern like fig.9

V Within the pattern, color sequence should be aligned: W-Y-C-G-M-R-BLUE-BLACK

(If color sequence is reversed(Black -> ... > White), reversethe pattern with REV key, when using Master patterngenerator like MSPG-925)

V If Minimum Black Level and/or Maximum White Level is not correct, Do select 100% Color Bar Pattern.

8-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator

(Which has 720p Ypbpr output & PC 1024x768 60Hz withStandard(0.7Vpp) Vertical 100% Color Bar Pattern as Fig.9)

8-2. Method of auto component color balance1) Input the Component 720p 100% Color Bar signal into

Component1 or Component2.2) Set the PSM to Standard mode in Picture menu.3) Press INSTART key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means complete adjustment

9. Auto RGB Color Balance[Requirement]It is very import to use correct adjustment pattern like fig.9

V Within the pattern, color sequence should be aligned: W-Y-C-G-M-R-BLUE-BLACK(If color sequence is reversed(Black -> ... > White), reversethe pattern with REV key, when using Master patterngenerator like MSPG-925)

V If Minimum Black Level and/or Maximum White Level is notcorrect, Do select 100% Color Bar Pattern.

9-1. Required T est Equipment1) Remote controller for adjustment2) 802F Pattern Generator

(Which has VGA 60Hz PC Format output with standard(0.7Vpp) Vertical 16 Gray Scale pattern as Fig.10)

9-2. Method of Auto RGB Color Balance1) Input the PC 1024x768 60Hz 100%Color bar into RGB.2) Set the PSM to Standard mode in Picture menu.3) Press ADJ key on R/C for adjustment.4) Press the G(Vol. +) key operate To set, then it becomes

automatically.5) Auto-RGB OK means completed adjustment.

(Fig. 10) Auto RGB Color Balance Test Pattern

(Fig. 9) Auto Component Color Balance Test Pattern

(Fig. 8) Pattern for Adjustment of White Balance

216 Level (85 IRE)

10. Default value in adjustment mode

10-1. Auto Color Balance (Component/RGB)

10-2. White Balance

- 15 -

(Fig. 12) Default Value on OSD

(Fig. 11) Default Value on OSD

Auto Color Balance(HEX)

Auto-RGB G To SetSource CortezRed Offset1 22Green Offset1 24Blue Offset1 23Red Offset2 45Green Offset2 43Blue Offset2 37Red Gain 014Green Gain 031Blue Gain 011Reset G To Set

White Balance(Hex)

Red Gain 82Red Offset 80Green Gain 86Green Offset 7DBlue Gain 7EBlue Offset 80Reset G To Set

- 16 -

TROUBLE SHOOTING GUIDE

1. Power Board

1-1. The whole flowchart which it follows in voltage output state

Start check

Manufacture enterprisemeaning of a passage

1. Check the Power Offcondition.

Doesn't the screen whole come

out?

Is it identical with Power Off

condition?

Yes

Yes

No

No

No

No

No

2. Check the Interfacesignal condition.

Is the Interface signal operated?

Yes

3. Check the St-by 5Vsignal circuit.

Doesn't the low pressure output

come out?

Doesn't the St-by 5V signal

come out?

Yes

Yes

No

4. Check the 5V Monitorsignal circuit.

Doesn't the 5V Monitor signal

come out?

Yes

7. Check the VSC Vs-ONsignal

Doesn't the high tension output

come out?

Doesn't the VSC signal Vs-ON

come out?

Yes

Yes

Doeshigh tension

output voltage Dropoccur?

When theY B/D Module

input connector isremoved, does output

voltage dropoccur?

When theY, Z B/D Module

input connector is remove,does Power Board high tension

output voltage Dropoccur?

Yes No No

9. Check the PowerBoard Output high

tension circuit

Yes

10. Check the Z B/DModule output circuit

Yes

When theZ B/D Module

input connector isremoved, does output

voltage Drop occurs?

11. Check the Y B/DModule output circuit

Yes

No

8. Check the Vs, Vavoltage output circuit.

Doesn't the Vs, Va voltage output

come out?

Yes

No

No

5. Check the VSC RL-ONsignal.

Doesn't the VSC signal RL-ON

come out?

Yes

6. Check the VSC lowpressure output

Doesn't the VSC low pressureoutput come out?

Yes

- 17 -

1-2. Sony Power Board Structure

1 2 3

T502: Vs Trans

T702: Va Trans

T101: St-by Trans

T103: Low Voltage Trans

- 18 -

1-3. Sanken, LGIT Power Board Structure

1 2 3

T221: Vs Trans

T271: Va Trans

T121: St-by Trans

T201: Low Voltage Trans

- 19 -

2. No Power

(1) SymptomØ Does’t minute discharge at module. Ø Non does not come in into the front LED.

(2) Check following

Is plug in power cord? Plug in power cord.

Yes

No

Is the Line Filter and PowerBoard Cable connected?

Connect the Cable.

Yes

No

Is the Fuse(F101) onPower Board normal?

Replace the Fuse.

Yes

No

Is the Power Board and 7P ofVSC Board Cable connected?

Connect the Cable.

Yes

No

After the cable connect is removedto Power Board(except the CN101connection cable), the AC voltagemarking is authorized on manual.When ST-BY 5V is not operated,replace Power Board.

- 20 -

3. Protect Mode

(1) SymptomØ After once shining, it does not discharge minutely

from moduleØ The Rely falls(The sound is audible “click”) Ø It is converted with the color where the front LED

is red from green.

(2) Check following

Is the Power Boardnormal ?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

ReplaceY-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Boardnormal?

ReplaceX-Board.

Is the output voltage normal afterremove P1, 2, 4, 9, 10 connector of

Ctrl-B/D?

Yes

No Yes

Is the Y-Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) on Y-B/D normal?(In case of open is replace)

Yes

No Yes Yes

ReplaceZ-Board.

Is the Z-Boardnormal?

Is the output voltagenormal after removeP1 connector of Z-

B/D?

Is the Fuse (FS1, FS2) on Z-B/Dnormal? (In case of open is replace)

Yes

No Yes

Is the X- Boardnormal?


X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is the VSC Board normal?

Is the output voltage normal afterremove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, 1100 normaloperation: Replace VSC Board

Yes

No

Is the COF of X, Y, Znormal ?

No

Yes

Yes

- 21 -

4. No Raster

(1) SymptomØ Does’t minute discharge at module. Ø It maintains the condition where the front LED is green.

(2) Check following

Is the Power Boardnormal?

Replace thePower Board.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is the each connectornormal?

Replace theconnector.

ReplaceY-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is the Ctrl Board normal?

ReplaceX-Board.


Ctrl-B/D?

Yes

No Yes

Is the Y-Boardnormal?

Is the output voltagenormal after removeP5, P6 connector of

Y-B/D?

Is the Fuse(FS2) normal on Y-B/D?(In case of open is replace)

Yes

No Yes Yes

ReplaceZ-Board.

Is the Z- Board normal?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is the Fuse(FS1, FS2) normal onZ-B/D? (In case of open is replace)

Yes

No Yes

Is the X- Board normal?


X-B/D?

After remove P1, P2, P3 output voltagenormality: Replace Right X-B/DAfter remove P4, P5 output voltagenormality: Replace the Left X-B/D

Yes

No Yes

Is the VSC Board normal?

Is the output voltage normal afterremove P1001, P1100?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1001, P1100 normaloperation: Replace the VSC Board

Yes

No

Is the COF of X, Y, Znormal?

No

Yes

Yes

- 22 -

5. In case of occurring strange screen into specific mode

5-1. In case the OSD does not displayed

(1) SymptomØ LED is greenØ The minute discharged continuously becomes accomplished from module

(2) Check following

Is the LVDS cablenormal ?

Is the VSC Boardnormal?

Is the LVDS cableconnected well?

Cable inserts well.Yes

No

No

Yes

Does the FIL8532 IC(IC800) Operates ?

Replace FIL8532IC(IC800).

No

Is the Ctrl Board ofModule normal?

Replace Ctrl B/D.No

No

YesReplace VSC B/D

Replace the cable.Yes

- 23 -

5-2. In case of does’t display the screen into specific mode

(1) SymptomØ The screen does not become the display from specific input mode

(RF, AV, Component, RGB, DVI).

(2) Check followingØ Check the all input mode should become normality display.Ø Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become

normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

(4) In the case of becomes unusual display from RF, AV mode

(5) In the case of becomes unusual display from Component, RGB mode

(6) In the case of becomes unusual display from HDMI mode

Is the Tuner normal?

Is the CXA2069Qnormal?

Is the Tuner Cableconnected well?

Cable inserts well.Yes

No

No

Yes

Is the FIL8532normal?

Replace the Tuner

No

Is the Input voltage, IIC Communicationand CVBS output normal?

Yes

Is the Input voltage, IICCommunication and HV sync

normal?

NoReplace the IC

No

Is normal the Input voltage, IICCommunication and HV sync?

NoReplace the IC

No

Is the CXA2069Qnormal?

Yes



normal?

NoReplace the IC

No


normal?

NoReplace the IC

No



normal?

NoReplace the IC

No

Is the Sil9011normal?

Yes



normal?

NoReplace the IC

No


normal?

NoReplace the IC

No

- 24 -

6. In case of no sound

(1) SymptomØ LED is greenØ Screen display but sound is not output

(2) Check following

Is the SPK cablenormal?

Is the SPK cableconnected well?

Cable inserts well.

No

No

Replace IC400

No

Replace IC401

No

Replace SPK cableYes

Yes

Is the RF/ AV/Component/ RGB/

HDMI sound normal?

No Does IC400Operates ?

Does IC401Operates ?

Replace IC402

No

Does IC402Operates ?

Replace VSC B/D

Yes Yes

PRINTED CIRCUIT BOARD

- 25 -

MAIN(TOP)

MAIN(BOTTOM)

- 26 -

RCA(TOP) RCA(BOTTOM) CONTROL

POWER SWITCH(TOP) POWER SWITCH(BOTTOM)

- 27 -

BLOCK DIAGRAMC

able

RC

A B

lock

Dia

gram

- 28 -

Sca

rt B

lock

Dia

gram

Cab

le

MEMO

- 29 -

- 30 -

EXPLODED VIEW

305

300

200

301

303

530310

400

580501

540

541

520

600

601

101

103

102

220

230

304

302

208

201

207

206

205

204

203

202

- 31 -

101 5900V12003C FAN, G1225S12B2-FS DONGYANG DC AXIAL 12V 120MM 1250 PRM 3P 280MM HOUSING

102 4980V01018A SUPPORTER, FAN EGI LEFT PDP DN-50PY10

103 4980V01017A SUPPORTER, FAN EGI RIGHT PDP DN-50PY10

200 6348Q-C043M PDP, 50” 1365*768 PDP50X30010.AKLGG

6348Q-C049H PDP, 50” 1365*768 PDP50X30010.ADDDB

6348Q-C049N PDP Module, 50” 1365*768 PDP50X30010.AKDDG

201 6871QCH059A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 50X3 CTRL LGPCM1224

202 6871QDH088A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV TOP

203 6871QDH089A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X3 YDRV BOTTOM

204 6871QLH049A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 50X3 X-LEFT(TCP)

205 6871QXH030A PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT _ 50X3 X-CENTER (TCP)

206 6871QRH057A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 50X3 X-RIGHT (TCP)

207 6871QYH039A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT FOR 50X3

208 6871QZH044A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT FOR 50X3

220 4980900191A SUPPORTER, ASSY ADC MODULE ASSY RIGHT 50PM1M

4980900191B SUPPORTER, ASSY ADC SKD MODULE ASSY RIGHT 50PM1M

230 4980900192A SUPPORTER, ASSY ADC MODULE ASSY LEFT 50PM1M

4980900192B SUPPORTER, ASSY ADC SKD MODULE ASSY LEFT 50PM1M

300 3091V00724A CABINET ASSEMBLY, 50PM10 RF04GA NON

3091V00724B CABINET ASSEMBLY, 50PM10 RF04GA C/SKD

301 4980V00C24A SUPPORTER, FILTER EGI TOP ASSY

4980V00C24C SUPPORTER, FILTER AL MZ-50PM10 TOP SKD

302 4980V00C25A SUPPORTER, FILTER EGI BOT ASSY

4980V00C25C SUPPORTER, FILTER AL MZ-50PM10 BOT SKD

303 4980V00C27A SUPPORTER, FILTER EGI SIDE L ASSY

4980V00C27C SUPPORTER, FILTER AL MZ-50PM10 SIDE L SKD

304 4980V00C26A SUPPORTER, FILTER EGI SIDE R ASSY

4980V00C26B SUPPORTER, FILTER AL MZ-50PM10 SIDE R ASSY C/SKD

305 5230V00017B FILTER(MECH), 50PX5D-UB LGM50-03 MITSUI 50” CLASS B GLASS FILTER

310 5020V01004C BUTTON, CONTROL 42PM10 6KEY

400 3809V00502A BACK COVER ASSEMBLY, 50PM10 NO WARNING

3809V00502C BACK COVER ASSEMBLY, 50PM10 NON MZ-50PM10 SKD NO WARNING

3809V00502F Cover Assembly, MT-50PM10 NON AUSTRALIA

3809V00502L Cover Assembly, 50PM1M-TA RF052A 50” HONGKONG WITH 412-737A

501 3301900007A PLATE ASSEMBLY, AV PLATE ASSY 3300900001 3300900002 50PM10 X3

520 6871VMMF41A PWB(PCB) ASSEMBLY,MAIN RF-052A H2.MNT. MT-50PM15

530 6871VSMS70A PWB(PCB) ASSEMBLY,SUB CONT RF052A H2 50PM1M

540 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU

541 5020900001A/ B BUTTON, POWER 50PM10/20 PC-ABS 1KEY X3 MODULE

580 6709V00001A POWER SUPPLY ASSEMBLY, 50INCH AF05GA 480W 1H259W SANKEN 50 INCH LOW END PSU

600 6871VSMAFFA PWB(PCB) ASSEMBLY,SUB RF052A H2 MONITOR RCA ATTACHABLE 1 TUNER

6871VSMANNA PCB Assembly,Sub SUB M.I RF052A 60PZ9M-TA . H2 MONITOR RCA ATTACHABLE NO TUNER

601 4980V00C30K/ P/ S SUPPORTER, AV INTERFACE EGI 50PM1MA-TA/50PM1MB-TA

EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

MIC39100 MICREL 3P SOT223 R/TP

BA033FP-E2 ROHM 3P-SOP,TO252-3 R/TP 3.3V

KA7809R, FAIRCHILD 2P D-PAK, R/TP IC

SC156515M-1.8TR SEMTECH 5P/TO-263-5






KIA78R05F KEC 5PIN DPAK R/TP 1A,5V



SII9011CLU(PB FREE) SILICON IMAGE 128P

AT24C02N-10SI-2.7 ATMEL 8P SOIC R/TP


MC34063ADR2G ON SEMI SO-8P R/TP

CXA2069Q QFP64 BK I2C BUS AV S/W

LA7217M MFP14 TP SYNC SEPARATOR

MSP4410K MICRONAS 80P/PQFP

NSP-2100A,LF NEOFIDELITY TQFP 64P

TAS5122DCARG4,LF 56P/TSSOP R/TP

74HC14D 14SOP TP SHITTER TRIGGER

AT24C02N-10SI-2.7 ATMEL 8P SOIC

74HC14D 14SOP TP SHITTER TRIGGER

OPA3692IDBQ BUR BROWN 16PIN SSOP

ICL3232CBNZ INTERSIL 16P/SOP R/TP



LM75CIMX-3 8P/SOP R/TP

FLI8532BD-LF GENESIS 416P/PBGA

24LC256T-I/SMG(PB FREE)

K4D261638F-LC50,LF TSOPII 66P

K4D261638F-LC50,LF TSOPII 66P

BSS83 TP PHILIPS N-CHANNEL S/W TR






CHIP 2SC3875S(ALY) BK KEC








KRA102S R/TP KEC SOT23 CHIP TR


REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q1200

Q1401

Q1402

Q201

Q202

Q203

Q204

Q205

Q207

Q300

Q301

Q302

Q303

Q304

Q305

Q400

Q401

Q402

Q403

Q404

Q405

Q406

Q407

Q408

D1005

D1006

D1007

D1008

D1009

D1010

D1012

D1013

D1100

D1105

D1106

D1107

D1109

D1110

D1200

D1201

D1500

D500

D501

D502

D504

D505

D506

D600

ZD300

ZD301

ZD400

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

0TR387500AA

0TR102008AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD200009AF

0DD200009AF

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD184009AA

0DS113379BA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DR050008AA

0DR050008AA

0DR050008AA

0DD100009AM

0DR050008AA

0DR050008AA

0DZRM00248A






CHIP 2SA1504S(ASY) BK KEC



















KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US

RU2M V(1) TP R-TMD 400V 1.1A 20A 0.4US

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS184 TP KEC - 85V - 300MA

1SS133 T-72 TP ROHM KOREA DO34 90V

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

KDS226 TP KEC

SD05.TC R/TP SEMTECH SOD323 5V 5A 15A



EU1ZV(1) TP E/EO-TMD 200V



RLZ8.2B-TE11 R/TP LLDS(LL-34) 500MW


IC1000

IC1001

IC1002

IC1003

IC1004

IC1005

IC1100

IC1101

IC1102

IC1103

IC1104

IC1105

IC1200

IC1201

IC1502

IC202

IC300

IC301

IC400

IC401

IC402

IC407

IC500

IC502

IC509

IC600

IC601

IC602

IC603

IC800

IC802

IC901

IC902

IC1202

IC1203

IC200

IC201

IC503

IC504

Q100

Q1000

Q1001

Q1002

Q1003

Q1004

Q101

Q101

Q102

Q102

0IPRPML001A

0IMCRRH001A

0IMCRFA010A

0IPMG00027A

0IMCRRH001A

0IMCRRH001A

0IMCRRH001A

0IPRPML001A

0IPMG00027A

0IPMGKE030A

0IPMG00027A

0IPRPML001A

0IPRPS5005A

0IMMRAL014B

0IPMGKE030A

0IPMGON013B

0ISO206900A

0ISA721700C

0IMCRMN028B

0ILNR00015A

0IMCRTI028C

0IPH741400E

0IMMRAL014B

0IPH741400E

0IPRPBB005A

0IPRP00009A

0IPMGKE032A

0IPMGKE032A

0IPRPNS054A

0IMCR02005A

0IMMR00024A

0IMMR00002A

0IMMR00002A

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR830009BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR102008AA

0TR387500AA

IC

TRANSISTOR

- 32 -

DIODE

- 33 -


ZD600

C1000

C1005

C1007

C1009

C1010

C1019

C103

C103

C1030

C1043

C1046

C1047

C1050

C1051

C1064

C1065

C1066

C1067

C1068

C1069

C1071

C1073

C108

C1082

C1083

C1084

C1085

C1087

C1098

C1099

C1102

C1105

C1107

C1108

C1110

C1115

C1116

C1117

C1118

C1119

C1120

C1126

C113

C1136

C1137

C1138

C114

C1148

C1156

0DR050008AA

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

0CE477DJ618

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE477DJ618

0CE227VF6DC

0CE477SF6DC

0CE106SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE476SF6DC

0CE476SF6DC


470UF MVG 16V 20% R/TP(SMD) SMD


100UF MVG 16V 20% SMD R/TP

































470UF STD 35V 20% FL TP 5


220UF MV 16V 20% R/TP(SMD) SMD


470UF STD 35V 20% FL TP 5











C1159

C1160

C1162

C1166

C1185

C1186

C1187

C1194

C1199

C1200

C1201

C1225

C1230

C1231

C1245

C1247

C1304

C1306

C1311

C1312

C1313

C1315

C1316

C1317

C1318

C1481

C1482

C1502

C1507

C1514

C1515

C1516

C1832

C1833

C1834

C204

C210

C211

C214

C215

C215

C221

C238

C241

C300

C304

C305

C307

C315

C318

C319

C320

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CK105DF64A

0CK105DF64A

0CE106SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE475SK6DC

0CE475SK6DC

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE477SF6DC

0CE475SK6DC

0CE477SF6DC

0CE106SF6DC

0CE105SK6DC

0CE475SK6DC

0CE477SF6DC

0CE107SF6DC

0CE476SK6D8

0CE107SF6DC

0CE226SF6DC

0CE107SF6DC

0CE476SF6DC

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A













1UF 2012 16V 20% F(Y5V) R/TP

1UF 2012 16V 20% F(Y5V) R/TP












4.7UF MVG 50V 20% SMD R/TP


















47UF MVG,MC 50V 20% SMD TAPPING





2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;

CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic

RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible

CAPACITOR

- 34 -


C335

C337

C342

C368

C370

C371

C402

C403

C407

C413

C418

C419

C421

C425

C444

C451

C456

C457

C462

C463

C464

C465

C477

C480

C481

C482

C483

C484

C485

C495

C527

C545

C546

C547

C548

C549

C550

C553

C555

C557

C559

C610

C614

C615

C620

C621

C622

C832

C833

C834

C835

C836

0CE476SF6DC

0CE105SK6DC

0CE105SK6DC

0CK225DFK4A

0CK225DFK4A

0CK225DFK4A

0CE476SF6DC

0CE106SF6DC

0CE107SF6DC

0CE335VK6DC

0CE107SF6DC

0CE107SF6DC

0CK105DF64A

0CE226SF6DC

0CE107SF6DC

0CK105DF64A

0CK105DF64A

0CE335VK6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SK6DC

0CF4741L438

0CE108DJ618

0CE475SK6DC

0CE475SK6DC

0CF4741L438

0CF4741L438

0CF4741L438

0CE108DJ618

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477VF6DC

0CE477VF6DC

0CE477VF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC




2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP

2.2UF 2012 16V 20%,-20% F(Y5V) R/TP




3.3UF MV 50V 20% R/TP(SMD) SMD



1UF 2012 16V 20% F(Y5V) R/TP



1UF 2012 16V 20% F(Y5V) R/TP

1UF 2012 16V 20% F(Y5V) R/TP

3.3UF MV 50V 20% R/TP(SMD) SMD





0.47UF D 63V 5% TP 5 M/PE NI

1000UF STD 35V 20% FL TP 5



0.47UF D 63V 5% TP 5 M/PE NI

0.47UF D 63V 5% TP 5 M/PE NI

0.47UF D 63V 5% TP 5 M/PE NI

1000UF STD 35V 20% FL TP 5
























C837

C838

C839

C840

C851

C853

C884

C896

C901

C904

C905

C930

C946

C947

C952

L1000

L1101

L1102

L1103

L1104

L1124

L409

L410

L411

L412

C1

C2

C3

C4

C5

C6

C7

C8

JK401

JK503

JK601

P1001

P100A

P100B

P101

P1100

P400

P401

P600

P601

P800

P801

P802

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0032A

6140VB0032A

6140VB0032A

6140VB0032A

366-036B

6631V00045K

6631V12047J

6631V25032E

6631V25083G

6631V39015E

6631V39016E

6631V39021H

385-173B

6630G70021A

6630VGA004B

366-921F

6630VL01280

6630VL01380

6602T12002M

366-921J

366-932C

366-932B

366-932B

366-932B

6602T12006M

6630VM01604

6630VM01702
















26UH 1UEWPHY 22.5TURN YL-9N 0.4






DBF-1015A 15.5UH 10PIE DIGITAL AUDIO




STAPLE

10P 2.5MM 550MM H-H UL1007AWG24

13P 1.25MM 500MM H-H UL1061AWG28

3P 2.5MM 300MM H-H UL1007 AWG26

7P 2.5MM 400MM H-H UL1007 AWG24

4P 3.96MM 300MM H-H UL1007AWG18

10P 3.96MM 300MM H-H UL1007AWG18

4P 3.96MM 450MM H-H UL1672AWG18

VER TYPE . 4 . 2LINE 4P A+B

DV11251-PV8-PF FOXCONN 30P 2.54MM

69107-0921 MOLEX 9P 2.77MM

GIL-G-07P LGC 7PIN 2.54MM STICK

2-557100-1 AMP 80P 2.54MM PLUG

2-557101-1 AMP 80P 2.54MM RECEPTACLE

53261-1390 MOLEX 13P 1.25MM R/A SMD

GIL-G-10P LGC 10PIN 2.54MM STICK

IL-G-04P LGC 2.5MM S/T STICK




53398-1390 MOLEX 13P 1.25MM S/T SMD

YW396 4P 3.96MM ANGLE, MN-60PZ12

YW396 2P 3.96MM (ANGLE TYPE)




COIL

CONNECTOR

- 35 -


P803

AR1200

AR1201

AR1202

AR1203

AR1204

AR1205

R1112

R1113

R230

R618

R801

R802

D1003

D1101

D1102

D1103

D1104

LD101

SW102

SW103

SW105

SW106

SW107

SW108

SW800

SW800

IC403

IC404

IC406

L100

L1004

L1005

L1006

L1007

L1008

L1009

L101

L1010

L1011

L1012

L1013

L1014

L1015

6602T12007D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RS0472K607

0RS0472K607

0RD0331H609

0RD0152H609

0RKZVTA001L

0RKZVTA001L

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL200000CA

140-313B

140-313B

140-313B

140-313B

140-313B

140-313B

6600VM2006A

6600VR1004A

6200VJS001B

6200VJS001B

6200VJS001A

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

GT121-31P-TD LGC 31P 1.25MM DUAL S/T

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

22 OHM 1 / 16 W 1608 5% R/TP 4P E24

47 OHM 2 W 5.00% TA62

47 OHM 2 W 5.00% TA62

3.3 OHM 1/2 W 5.00% TA52

15 OHM 1/2 W 5.00% TA52

1.0M OHM 1/2 W 5% TA52 UL PILKOR

1.0M OHM 1/2 W 5% TA52 UL PILKOR

SAM2333 TP GREEN:10MCD, RED:6MCD





SAM5670(DL-2LRG) BK Y-GREEN -

2LEAD 160G(TA) 5V 0.001A HORIZONTAL .G






SDDF3PATP011 250V 4A HORIZONTAL .G

SKHMPW 5P J-ALPS .V .A HORIZONTAL .G

ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A

ZJYS51R5-2PL(T) TDK R/TP 50VOLT 2A

ZJY51R5-4P TDK DIP DC 50VOLT 2A

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM


L1016

L1017

L1018

L1019

L102

L1020

L1021

L1022

L1023

L1024

L103

L104

L1106

L1107

L1108

L111

L112

L1125

L1126

L1127

L113

L1131

L114

L115

L116

L119

L120

L1204

L1205

L1206

L1207

L1208

L1209

L121

L122

L137

L1501

L1502

L1503

L202

L203

L204

L300

L301

L400

L401

L402

L403

L406

L407

L408

L500

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6200J000013

6210VC0005A

6210VC0005A

6200J000013

6200J000013

6200J000013

6210VC0005A

6200J000013

6210VC0005A

6210VC0005A

6210VC0005A

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-321611-0500P-N2 R/TP 500 OHM

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM




SWITCH

FILTER & CRYSTAL

LED

RESISTOR

- 36 -


L501

L502

L503

L506

L514

L515

L516

L517

L604

L901

L902

X1200

X300

X400

X800

JK101

JK102

JK103

JK104

JK105

JK1200

JK400

JK502

A1

A1

A2

A3

A3

CA1

CA2

F801

IC900

PA101

TU201

6210VC0005A

6200JB8010L

6200JB8010L

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6200J000013

6212AB2845A

166-E02F

156-A02M

6212AB2844A

6612VJH020C

6612VJH019C

6612VJH020B

380-363G

6612JH003CA

6612B00015A

6612JH003CA

6612F00006F

3828VA0564E

38289U0516A

6710T00017M

64109EP003A

6410VBH003H

68509A0002A

6850J00005C

0FS1002B53K

6927V1298AH

6712000002B

6700MF0012C

BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-201209-1000L-N2 R/TP 1000OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

MLB-321611-0500P-N2 R/TP 500 OHM

RESONATOR,CRYSTAL ABLS-27.000MHZ

RESONATOR,CERAMIC CSBLA500KECZF09-B0

RESONATOR,CRYSTAL HC49U 18.432MHZ

RESONATOR,CRYSTAL ABLS-19.6608MHZ

PPJ122C A/V 6P(COMPONENT)+SHIELD+GOLD

PPJ121-22 A/V 4P FOR EMI WITH SWITCH RED

PPJ122B A/V 6P+SHIELD+GOLD

6046B-01S PARKELEC H=8.0 WITH S/W,SHIELD

PPJ137A AUDIO L-MONO JACK

DC1R019NDA JAE 1.0MM,19PIN,HDMI JACK

PPJ137A AUDIO L-MONO JACK

KJA-PH-3-0064 KSD 3.5PHI 14P DUALJACK

MANUAL, USER B/D AR/FR/EN 138L TX 114%

MANUAL, USER EN 017M/N-TX

REMOTE CONTROLLER, RF052A NON-EU

POWER CORD, SP-023+IS-14 1870MM

POWER CORD, 003D-G/SOURCING 2800MM

CABLE,COAXIAL 150MM KCA-NS-0-0053 KSD

CABLE,DVI LVDS UL20276 AWG30 600MM

FUSE, 10000MA 250 V 5.2X20

SOFT WARE, 3.11V 59B6 1366X768

REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1

TUNER, TAFM-W103P LGIT MULTI FS


ACCESSORIES

MISCELLANEOUS

JACK

Apr., 2006Printed in KoreaP/NO : 3828VD0223T

Documents

Service Manuals LG TV PLASMA 50PM1MA 50PM1MA Service Manual