Series WSSE / LSSE Butterfly Valve 300MM - Challenger … · Flange holes comply with AS2129 E & ANSI Class 125 ... line-up the valve stem with the gear operator bore and slide the

Series WSSE / LSSE Butterfly Valve 50MM - 300MM

1 QAD#IMI030.REVA.04.06.12

www.challengervalves.com.au

Installation

Operation

Maintenance


2 QAD#IMI030.REVA.04.06.12

Index

1. INTRODUCTION 3

1.1 Design Features

1.2 Flange and Pipe Compatibility 4

1.3 Operating Pressure 4

1.4 Product Storage 4

1.5 Product Marking 5

2. INSTALLATION MATERIAL 5

2.1 Installation Instructions 5

2.2 Manual Operator Installation (Lever) 7

2.3 Manual Operator Installation (Gear) 8

3. MAINTENANCE AND REPAIR 9

4. ASSEMBLY /DISASSEMBLY INSTRUCTIONS 9

5. TECHNICAL 10

5.1 Dimensions and Weights 10

5.2 Torque

5.3 CV Valves - Sizing


3 QAD#IMI030.REVA.04.06.12

1. INTRODUCTION

1.1 DESIGN FEATURES

Available in wafer or lug body. Flange holes comply with AS2129 E & ANSI Class 125/150 dimensions. Cast-in top plate with ISO5211 mounting dimensions provides direct-mounting of Challenger HQ, HP actuators and manual operators. The face-to-face dimensions are designed to comply with ISO5752, BS5155. Wafer body features two alignment holes for ease of installation. Through-shaft design. Disc-to-seat interface provides bubble-tight shut-off with reduced torque and extended service life. Factory tested to 110% of full rated pressure in both directions before shipping. STEM RETAINING SYSTEM

The stem is securely contained in the body by means of a retaining washer and circlip situated on top of the shaft and fixed into a groove in the body. For maintenance, with only a small hand tool, the circlip can be removed, the shaft then withdrawn, and the valve easily dismantled.

STEM BUSHING

Heavy duty Acetal bushing aligns and supports the stem and absorbs side thrust STEM SEAL

Double - U “cupseal” design is self-adjusting and gives positive sealing in both directions to prevent external substances from entering the stem area. STEM & DISC DRIVE CONNECTION

"Challenger” features all the benefits of a high strength one piece through stem design. The disc drive connection is achieved by using a close tolerance Double “D“ arrangement . One piece high strength stem design No disc retaining screws or pins


4 QAD#IMI030.REVA.04.06.12

SEAT

"Challenger“ valves are designed with a unique seat locking feature and a full encapsulating liner providing seat retention features which virtually guarantee elimination of any seat movement during both seating and unseating operations. This unique feature also allows for full valve pressure rating with the downstream flanged removed (lugged pattern Valves). CHALLENGER VALVES HAVE PRIMARY AND SECONDARY SEALING FEATURES

The primary seal is obtained by an interference fit of the unique moulded seat flat with the disc hub with the seat firmly retained within the body recess. Sealing capabilities do not rely on external flanging. The secondary seals are achieved by having an interference fit between the stem diameter and the seat hole, plus further added pressure from the moulded "O” rings. These three sealing actions are unique in the design to achieve higher pressure ratings and virtually guarantee the prevention of any line media from escaping into the body/shaft area. 1.2 FLANGE AND PIPE COMPATIBILITY

Challenger” Butterfly Valves are designed to fit between the following piping flanges: AS2129 Table E Wafer Pattern AS2129 Table E Lugged Pattern ANSI 125 Cast iron flanges ANSI 150 Steel flanges Note: When installing valves in schedule 80 piping, make sure the valve is properly centered between the pipe flanges to prevent disc edge damage since the clearance between the disc O.D. and the pipe I.D. is reduced. If there is a compatibility question, compare the minimum pipe I.D. 1.3 OPERATING PRESSURES

Challenger Series 50mm - 300mm - 16 Bar Fully Rated 50mm - 300mm - 3 bar Undercut Disc 1.4 PRODUCT STORAGE

The valves should be stored with the disc in the partially open position. The valves should be stored indoors in a clean, dry, well-ventilated place away from corrosive materials and protected from excessive dust and dirt. The valves should be stored on a rack or pallet off the floor and arranged to prevent damage during handling. Keep valves out of direct sunlight and in a cool location to prolong elastomer life. Valves should be protected to prevent damage to the flange faces, disc sealing edge and operator.


5 QAD#IMI030.REVA.04.06.12

1.5 PRODUCT MARKING

All “Challenger” Butterfly Valves are equipped with an identification tag attached to the valve neck. This tag provides the model number, max pressure rating, valve materials and unique serial number. The valve neck also provides the size of the valve.

2. INSTALLATION INFORMATION

“Challenger” butterfly valves are designed for use between the faces of AS2129 E & ANSI 125 and 150 pound flat, raised face, slip-on or weld-neck flanges at the pressure indicated on the nameplate. Flange gaskets should not be used. Consideration should be given to the proper piping alignment prior to the installation of any cast iron lug bodied valve. All “Challenger” butterfly valves are bi-directional with the ability to control flow equally in either direction. All “Challenger” Lugged Series butterfly valves may be used for dead-end service in either direction at their full pressure rating. 2.1 INSTALLATION INSTRUCTIONS

Step 1. Check to make sure that the pipe flange and valve sealing faces are clean and free from any debris (pipe scale, welding slag, etc.).

Step 2. Check the valve nameplate to ensure that the pressure and valve materials are correct for the application. WARNING! Butterfly valves should never be installed where service conditions could exceed the valve ratings. Failure to heed warning may result in personal injury or property damage. Step 3. The seat sealing face on the butterfly valves is wider than the valve body providing a leak proof seal when

compressed between pipe flanges. Therefore, no flange gaskets are required when installing any butterfly valve.

Step 4. To prevent damage to the disc sealing edge before installation, position the disc in the “partially open” position (Figure 1) so that the disc is still contained within the valve body.

FIGURE 1. VALVE IN PARTIALLY OPEN POSITION


6 QAD#IMI030.REVA.04.06.12

INSTALLATION INSTRUCTIONS

Step 5. Spread the pipe flanges apart allowing the valve to be supplied easily in between the flanges.

Step 6. Centre the valve between the flanges and loosely install all flange bolts. On the wafer valve, the flange bolts

that pass through the alignment lugs should be installed first. (Consult table 1 for the correct flange bolt size

and quantity)

TABLE 1. FLANGE BOLTING

Step 7. Slowly open the valve to the full open position (see figure 2) and back to the partially open position ensuring

that the disc moves freely without any obstruction. If no obstruction is encountered, return the valve to full

open position and hand tighten all flange bolts using the bolt tightening sequence shown in figure 3.

FIGURE 2. VALVE IN FULL OPEN POSITION FIGURE 3. BOLTING SEQUENCE

Step 8. Rotate the disc from the fully open position to the fully closed position and make sure that the valve is properly

centred and the disc edge does not make contact with the pipe ID. Return the disc to the full open position and tighten the flange bolts following the bolt tightening sequence shown in Figure 3. Do not fully tighten each flange bolt all at once. Tighten each bolt incrementally . several times. Continually cycle the valve from fully open to fully closed to ensure that there is proper disc clearance.

1

2

11

8

3

10

5

12

7

4

9

6

Size mm 50 65 80 100 125 150 200 250 300

AS2129 E M16 X 2.0 M16 X 2.0 M 16 X 2.0 M 16 X 2.0 M16 X 2.0 M20 X 2.5 M20 X 2.5 M 24 X 3.0 M 24 X 3.0

PCD 114 127 146 178 210 235 292 356 406

No. Holes 4 4 4 8 8 8 8 12 12

ASA125/150 UNC 5/8 UNC 5/8 UNC 5/8 UNC 5/8 UNC 3/4 UNC 3/4 UNC 3/4 UNC 7/8 UNC 7/8

PCD 120.5 139.5 152.5 190.5 216 241.5 298.5 362 432

No. Holes 4 4 4 8 8 8 8 12 12


7 QAD#IMI030.REVA.04.06.12

Required Gap between

Liner & Flange

Step 9. Bolts on flanges are not to be tightened to the extent where the flange is in contact with the body of the valve. The unique O-Ring sealing design allows positive sealing without the over tightening of the bolts. Over tightening of the bolts results in excessive valve torques restricting operation of the valve and potentially damaging the rubber seal. A gap should be visible after the bolts are tightened (see figure 4) (Refer to Table 2 for recommended bolt tensions).

FIGURE 4. O-RING SEALING DESIGN

TABLE 2. RECOMMENDED BOLT TENSIONS

Flange Face

Upon flange loading the Double Moulded O-

Ring surface area has been calculated to pro-

vide sufficient compression to firmly lock and

secure liner into mechanical dovetail joint, en-

suring effective sealing and reduced torques.

Valve Size Torque Ft-Ibs

50 30

65 30

80 35

100 40

125 45

150 50

200 60

250 80

300 120

350 120

400 130

450 140

500 140

The torque figures contained within this table are based on maximum pressure differentials listed for the product as noted, using standard discs, stems, body and materials of construction at ambient temperatures. Torque figures have reasonable safety factors for normal service, but for valves poorly handled, stored, installed or In service for extended periods of time, may have a dramatic effect on actual torque ratings, additionally for severe or special applications consult Challenger Valves and Actuators.


8 QAD#IMI030.REVA.04.06.12

2.2 MANUAL OPERATOR INSTALLATION LEVER HANDLE MOUNTING PROCEDURE

Step 1. First, start by loosely assembling the notch plate on the valve top plate. The notch plate should be installed with the notches in the first quadrant of the valve top plate with the stop tabs at the 12 o’clock and 3 o’clock position. The notch plate should be installed with the stop tabs pointing upward (Figure 5).

Step 2. Next, install the handle so that the lever fully engages in the notches when the lever is released and tighten the handle set screw.

Step 3. Compress the handle lever and position the disc so that the valve is in the fully closed position. Align the last notch on the notch plate at the 3 o’clock position with the handle lever and tighten the notch plate screws.

Step 4. Compress the handle lever and position the disc so that the valve is in the fully open position and release the lever. The lever should line-up with the first notch on the notch plate at the 12 o’clock position.

FIGURE 5. NOTCH PLATE

INSTALLATION POSITION


9 QAD#IMI030.REVA.04.06.12

MANUAL GEAR OPERATOR MOUNTING PROCEDURE

Step 1. First, rotate the valve disc to the fully open position. Step 2. Next, slide the hand wheel onto the end of the gear operator shaft. Line-up the hole in the hand wheel with

the hole in the gear operator shaft. Install the shear pin and rotate the gear operator to the open position. Step 3. Next, line-up the valve stem with the gear operator bore and slide the gear operator onto the valve with the

hand wheel pointing to the right of the valve. (See Fig 6.) Step 4. Make sure before sliding gear operator onto valve shaft, the indicator on the operator is indicating the same

position as the valve shaft. Step 5. Position the gear operator so that the tapped holes in the bottom of the gear operator line-up with the valve

top-plate mounting holes and install the mounting screws with lock washers. Step 6. Loosen the gear operator travel stops and rotate the hand wheel until the valve is in the fully closed

position. Tighten the gear operator stop on the right-hand side of the gear operator. (Note: There are two hex head set screws in tandem that represent the gear operator travel stops. Ensure that the first hex head screw is fully removed before loosening the travel stops.)

Step 7. Rotate the hand wheel until the valve is in the fully open position. Tighten the gear operator stop on the left-hand side of the gear operator.

Step 8. Cycle the valve from the fully open position to the fully closed position to make sure that the stops are set correctly.

FIGURE 6. GEAR OPERATOR INSTALLATION POSITION


10 QAD#IMI030.REVA.04.06.12

3. MAINTENANCE AND REPAIR

Challenger” butterfly valves are designed for extended service with minimal wear and servicing. No regular lubrication is required. Prior to any replacement or repair, the valve must be removed from the line following these precautions: The pipeline on either side of the valve must be depressurized and drained. Ensure that the disc is in the partially open or full closed position before removing the valve from the line. DO NOT remove an actuator or operator from the valve while the line is still pressurized.

4. ASSEMBLY/DISASSEMBLY INSTRUCTIONS

The “Challenger” butterfly valves have field replaceable parts. Once the valve is removed from the line, inspect the parts for wear. If valve parts show wear, replacement is necessary. Contact your local distributor for a replacement parts. DISASSEMBLY

1. Close the valve to the almost closed position and remove from pipeline. 2. Remove the operator (notch plate, lever, gearbox unit or actuator). 3. Remove internal circlip (Part No.8) 4. Pull the stem (Part No.4) out through the top of the ISO top mounting flange 5. The disc is then remove by pushing the disc (Part No.3) out side the liner (Part No.2) 6. Remove the liner by collapsing and pushing out the valve body

ASSEMBLY

1. Insert the liner by collapsing and pushing into valve body 2. Ensure the smaller hole in the liner, is align with the bottom hole in the valve body 3. Insert shaft seal (Part No.5) and thrust bearing (Part No.6) into the neck 4. Lubricate the disc and stem with a silicone base grease 5. Push the disc into the liner with the internally flatten side hole at the bottom 6. Align the top hole with the matching hole in the liner 7. Insert the shaft (Part No.4) small end first, and push through the disc until fully home. 8. Replace washer (Part No.7) and circlip (Part No.8) 9. Replace valve operator

1

2

3

4

5

6

7

8


11 QAD#IMI030.REVA.04.06.12

5. TECHNICAL

A

B D B

E

F

J

H

50 65 80 100 125 150 200 250 300

A 100 100 100 100 100 100 150 150 150

B 14 14 14 19.1 19.1 22 22 30 30

C 42.9 46 46 52.3 55.6 55.6 60.5 68.3 77.7

D 9.5 9.5 9.5 12.7 12.7 15.9 15.9 24 24

E 32 32 32 32 32 32 32 50 50

F 140 152 159 178 191 203 241 273 311

G 53 68 82 103 129 152 202 252 302

H 30.6 50 69 89 115.6 151.5 192.3 242.6 292.5

J 94 112 128 158 190 210 266 330 375

5.1 VALVE DIMENSIONS MOUNTING DIMENSIONS AND WEIGHTS

Size MM 50 65 80 100 125 150 200 250 300

ISO 5211 F07 F07 F07 F07 F07 F07 F10 F10 F10

PCD 70 70 70 70 70 70 102 102 102

Bolting X4 M8 M8 M8 M8 M8 M8 M10 M10 M10

Shaft ISO 11 11 11 14 14 17 17 22 22

Wafer KGs 3.5 4.5 5 7 8 10 17 25 43

Lugged KGs 4.5 5.5 6 9 12 13 22 33 46

Size MM 50 65 80 100 125 150 200 250 300

AS2129 E M16 X 2.0 M16 X 2.0 M16 X 2.0 M16 X 2.0 M16 X 2.0 M20 X 2.5 M20 X 2.5 M24 X 3.0 M24 X 3.0

PCD 114 127 146 178 210 235 292 356 406

No. Holes 4 4 4 8 8 8 8 12 12

ASA125/150 UNC 5/8 UNC 5/8 UNC 5/8 UNC 5/8 UNC 3/4 UNC 3/4 UNC 3/4 UNC 7/8 UNC 7/8

PCD 120.5 139.5 152.5 190.5 216 541.5 298.5 362 432

No. Holes 4 4 4 8 8 8 8 12 12

FLANGE DRILLING AND TAPPING INFORMATION

G

C


12 QAD#IMI030.REVA.04.06.12

5.2 TORQUE CAN BE DETERMINED BY THE FOLLOWING:

Challenger Butterfly valve Torque chart are for standard seats. Multiply this torque by the application factor 1. 1.0 x Operates once per week or more 2. 1.3 x Operates once per month 3. 1.5 x Operates once per 3 months 4. 1.7 x Modulating Service

The charted torques valves given are the total of all internal frictions.

The effects of dynamic torsion is not considered in this chart.

Torsional capability of valve shafts is not considered in this chart.

All torques valve testing was done with standard seats. 5.3 Cv VALVES - VALVE SIZING

FLOW CO-EFFICIENTS

Cv is defined as the volume of water in US gallons per minute that will flow through a given restriction or valve opening with a pressure drop of one psi at room temperature. Control Valve sizing –Butterfly Valves Recommended control angles are between 25° - 70° open. To convert Cv to Kv divide by 1.1553

Size Wet Service (Nm)

50 19

65 23

80 34

100 45

125 73

150 118

200 196

250 332

300 445

*Figures based on 16 bar pressure wet service

Size 20° 30° 40° 50° 60° 70° 80° 90°

50 7 16 28 49 77 128 198 219

65 10 23 42 68 108 178 288 316

80 15 36 65 109 167 278 427 498

100 26 16 108 178 275 458 715 815

125 43 98 177 278 447 737 1095 1290

150 59 138 247 398 637 1097 1590 1895

200 108 247 437 687 1100 1795 2790 3290

250 178 396 705 1100 1795 2995 4590 5390

300 256 587 995 1697 2695 4398 6790 7990

Documents

Series WSSE / LSSE Butterfly Valve 300MM - Challenger … · Flange holes comply with AS2129 E & ANSI Class 125 ... line-up the valve stem with the gear operator bore and slide the