SECTION 081113 - HOLLOW METAL DOORS AND FRAMESbarcom.cc › wp-content › uploads › 2016 › 11 › cc-honda-complete-div … · HOLLOW METAL DOORS AND FRAMES 081113 1 SECTION

JOHN MAHONEY ARCHITECT, LLC CORPUS CHRISTI HONDA 1608

HOLLOW METAL DOORS AND FRAMES 081113 1

SECTION 081113 - HOLLOW METAL DOORS AND FRAMES

PART 1 - GENERAL

1.1 SUMMARY

A. Section Includes:

1. Standard hollow metal doors and frames.

1.2 SUBMITTALS

A. Product Data: For each type of product indicated.

B. Shop Drawings: Include elevations, door edge details, frame profiles, metal thicknesses, preparations for hardware, and other details.

C. Schedule: Prepared by or under the supervision of supplier, using same reference numbers for details and openings as those on Drawings.

1.3 QUALITY ASSURANCE

A. Fire-Rated Door Assemblies: Assemblies complying with NFPA 80 that are listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at positive pressure according to UL 10C.

1. Temperature-Rise Limit: At vertical exit enclosures and exit passageways, provide doors that have a maximum transmitted temperature end point of not more than 450 deg F above ambient after 30 minutes of standard fire-test exposure.

B. Fire-Rated, Borrowed-Light Frame Assemblies: Assemblies complying with NFPA 80 that are listed and labeled, by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire-protection ratings indicated, based on testing according to NFPA 257 or UL 9. Label each individual glazed lite.

C. Smoke-Control Door Assemblies: Comply with NFPA 105 or UL 1784.

PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

1. Amweld Building Products, LLC. 2. Benchmark; a division of Therma-Tru Corporation. 3. Ceco Door Products; an Assa Abloy Group company. 4. Curries Company; an Assa Abloy Group company. 5. Deansteel Manufacturing Company, Inc. 6. Firedoor Corporation. 7. Fleming Door Products Ltd.; an Assa Abloy Group company.



8. Habersham Metal Products Company. 9. Kewanee Corporation (The). 10. Mesker Door Inc. 11. Pioneer Industries, Inc. 12. Security Metal Products Corp. 13. Steelcraft; an Ingersoll-Rand company. 14. Windsor Republic Doors.

2.2 MATERIALS

A. Cold-Rolled Steel Sheet: ASTM A 1008/A 1008M, CS, Type B; suitable for exposed applications.

B. Hot-Rolled Steel Sheet: ASTM A 1011/A 1011M, CS, Type B.

C. Metallic-Coated Steel Sheet: ASTM A 653/A 653M, Commercial Steel (CS), Type B; with minimum A40 metallic coating.

D. Frame Anchors: ASTM A 591/A 591M, Commercial Steel (CS), 40Z coating designation; mill phosphatized.

1. For anchors built into exterior walls, steel sheet complying with ASTM A 1008/A 1008M or ASTM A 1011/A 1011M, hot-dip galvanized according to ASTM A 153/A 153M, Class B.

E. Inserts, Bolts, and Fasteners: Hot-dip galvanized according to ASTM A 153/A 153M.

F. Grout: ASTM C 476, except with a maximum slump of 4 inches, as measured according to ASTM C 143/C 143M.

G. Mineral-Fiber Insulation: ASTM C 665, Type I.

H. Glazing: Division 08 Section "Glazing."

I. Bituminous Coating: Cold-applied asphalt mastic, SSPC-Paint 12, compounded for 15-mil dry film thickness per coat.

2.3 STANDARD HOLLOW METAL DOORS

A. General: Comply with ANSI/SDI A250.8.

1. Design: Flush panel. 2. Core Construction: Manufacturer's standard kraft-paper honeycomb, polystyrene,

polyurethane, polyisocyanurate, mineral-board, or vertical steel-stiffener core.

a. Fire Door Core: As required to provide fire-protection and temperature-rise ratings indicated.

b. Thermal-Rated (Insulated) Doors: R-value of not less than 6.0 deg F x h x sq. ft./Btu when tested according to ASTM C 1363.

3. Vertical Edges for Single-Acting Doors: Manufacturer's standard. 4. Top and Bottom Edges: Closed with flush or inverted 0.042-inch- thick, end closures or

channels of same material as face sheets. 5. Tolerances: SDI 117, "Manufacturing Tolerances for Standard Steel Doors and Frames."

B. Exterior Doors: Face sheets fabricated from metallic-coated steel sheet. Comply with ANSI/SDI A250.8 for level and model and ANSI/SDI A250.4 for physical performance level:



1. Level 2 and Physical Performance Level B (Heavy Duty), Model 1 (Full Flush).

C. Interior Doors: Face sheets fabricated from cold-rolled steel sheet. Provide doors complying with requirements indicated below by referencing ANSI/SDI A250.8 for level and model and ANSI/SDI A250.4 for physical performance level:

1. Level 1 and Physical Performance Level C (Standard Duty), Model 1 (Full Flush).

a. Width: 1-3/4 inches.

D. Hardware Reinforcement: ANSI/SDI A250.6.

2.4 STANDARD HOLLOW METAL FRAMES

A. General: Comply with ANSI/SDI A250.8.

B. Exterior Frames: Fabricated from metallic-coated steel sheet.

1. Fabricate frames with mitered or coped corners. 2. Fabricate frames as face welded unless otherwise indicated. 3. Frames for Level 2 Steel Doors: 0.053-inch- thick steel sheet.

C. Interior Frames: Fabricated from cold-rolled steel sheet.

1. Fabricate frames with mitered or coped corners. 2. Fabricate frames as face welded unless otherwise indicated. 3. Frames for Level 1 Steel Doors: 0.042-inch- thick steel sheet. 4. Frames for Wood Doors: 0.042-inch- thick steel sheet. 5. Frames for Borrowed Lights: 0.042-inch- thick steel sheet.

D. Hardware Reinforcement: ANSI/SDI A250.6.

2.5 FRAME ANCHORS

A. Jamb Anchors:

1. Masonry Type: Adjustable strap-and-stirrup or T-shaped anchors to suit frame size, not less than 0.042 inch thick, with corrugated or perforated straps not less than 2 inches wide by 10 inches long; or wire anchors not less than 0.177 inch thick.

2. Stud-Wall Type: Designed to engage stud, welded to back of frames; not less than 0.042 inch thick.

3. Compression Type for Drywall Slip-on Frames: Adjustable compression anchors. 4. Postinstalled Expansion Type for In-Place Concrete or Masonry: Minimum 3/8-inch- diameter

bolts with expansion shields or inserts. Provide pipe spacer from frame to wall, with throat reinforcement plate, welded to frame at each anchor location.

B. Floor Anchors: Formed from same material as frames, not less than 0.042 inch thick, and as follows:

1. Monolithic Concrete Slabs: Clip-type anchors, with two holes to receive fasteners. 2. Separate Topping Concrete Slabs: Adjustable-type anchors with extension clips, allowing not

less than 2-inch height adjustment. Terminate bottom of frames at finish floor surface.



2.6 HOLLOW METAL PANELS

A. Provide hollow metal panels of same materials, construction, and finish as specified for adjoining hollow metal work.

2.7 STOPS AND MOLDINGS

A. Moldings for Glazed Lites in Doors: Minimum 0.032 inch thick, same material as door face sheet.

B. Fixed Frame Moldings: Formed integral with hollow metal frames, a minimum of 5/8 inch high unless otherwise indicated.

C. Loose Stops for Glazed Lites in Frames: Minimum 0.032 inch thick, same material as frames.

2.8 LOUVERS

A. Provide sightproof louvers for interior doors, where indicated, that comply with SDI 111C, with blades or baffles formed of 0.020-inch- thick, cold-rolled steel sheet set into 0.032-inch- thick steel frame.

2.9 ACCESSORIES

A. Mullions and Transom Bars: Join to adjacent members by welding or rigid mechanical anchors.

B. Ceiling Struts: Minimum 1/4-inch-thick by 1-inch- wide steel.

C. Grout Guards: Formed from same material as frames, not less than 0.016 inch thick.

2.10 FABRICATION

A. Tolerances: Fabricate hollow metal work to tolerances indicated in SDI 117.

B. Hollow Metal Doors:

1. Exterior Doors: Provide weep-hole openings in bottom of exterior doors. Seal joints in top edges of doors against water penetration.

2. Glazed Lites: Factory cut openings in doors. 3. Astragals: Provide overlapping astragal on one leaf of pairs of doors where required by

NFPA 80 for fire-performance rating or where indicated.

C. Hollow Metal Frames: Where frames are fabricated in sections, provide alignment plates or angles at each joint, fabricated of same thickness metal as frames.

1. Welded Frames: Weld flush face joints continuously; grind, fill, dress, and make smooth, flush, and invisible.

2. Sidelight Frames: Provide closed tubular members with no visible face seams or joints, fabricated from same material as door frame. Fasten members at crossings and to jambs by butt welding.

3. Provide countersunk, flat- or oval-head exposed screws and bolts for exposed fasteners unless otherwise indicated.

4. Grout Guards: Weld guards to frame at back of hardware mortises in frames to be grouted. 5. Floor Anchors: Weld anchors to bottom of jambs and mullions with at least four spot welds per

anchor. 6. Jamb Anchors: Provide number and spacing of anchors as follows:



a. Masonry Type: Locate anchors not more than 18 inches from top and bottom of frame. Space anchors not more than 32 inches o.c. and as follows:

1) Two anchors per jamb up to 60 inches high. 2) Three anchors per jamb from 60 to 90 inches high. 3) Four anchors per jamb from 90 to 120 inches high. 4) Four anchors per jamb plus 1 additional anchor per jamb for each 24 inches or

fraction thereof above 120 inches high.

b. Stud-Wall Type: Locate anchors not more than 18 inches from top and bottom of frame. Space anchors not more than 32 inches o.c. and as follows:

1) Three anchors per jamb up to 60 inches high. 2) Four anchors per jamb from 60 to 90 inches high. 3) Five anchors per jamb from 90 to 96 inches high. 4) Five anchors per jamb plus 1 additional anchor per jamb for each 24 inches or

fraction thereof above 96 inches high. 5) Two anchors per head for frames more than 42 inches wide and mounted in metal-

stud partitions.

c. Compression Type: Not less than two anchors in each jamb. d. Postinstalled Expansion Type: Locate anchors not more than 6 inches from top and

bottom of frame. Space anchors not more than 26 inches o.c.

7. Door Silencers: Except on weather-stripped doors, drill stops to receive door silencers.

a. Single-Door Frames: Three door silencers. b. Double-Door Frames: Two door silencers.

D. Hardware Preparation: Factory prepare hollow metal work to receive templated mortised hardware according to the Door Hardware Schedule and templates furnished as specified in Division 08 Section "Door Hardware."

1. Locate hardware as indicated, or if not indicated, according to ANSI/SDI A250.8. 2. Reinforce doors and frames to receive nontemplated, mortised and surface-mounted door

hardware. 3. Comply with applicable requirements in ANSI/SDI A250.6 and ANSI/DHI A115 Series

specifications for preparation of hollow metal work for hardware. 4. Coordinate locations of conduit and wiring boxes for electrical connections with Division 26

electrical Sections.

E. Stops and Moldings: Provide stops and moldings around glazed lites where indicated. Form corners of stops and moldings with butted or mitered hairline joints.

1. Single Glazed Lites: Provide fixed stops and moldings welded on secure side of hollow metal work.

2. Multiple Glazed Lites: Provide fixed and removable stops and moldings so that each glazed lite is capable of being removed independently.

3. Provide fixed frame moldings on outside of exterior and on secure side of interior doors and frames.

4. Provide loose stops and moldings on inside of hollow metal work. 5. Coordinate rabbet width between fixed and removable stops with type of glazing and type of

installation indicated.

2.11 STEEL FINISHES

A. Prime Finish: Apply manufacturer's standard primer immediately after cleaning and pretreating.



1. Shop Primer: ANSI/SDI A250.10.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Hollow Metal Frames: Comply with ANSI/SDI A250.11.

1. Set frames accurately in position, plumbed, aligned, and braced securely until permanent anchors are set. After wall construction is complete, remove temporary braces, leaving surfaces smooth and undamaged.

a. At fire-protection-rated openings, install frames according to NFPA 80. b. Where frames are fabricated in sections because of shipping or handling limitations, field

splice at approved locations by welding face joint continuously; grind, fill, dress, and make splice smooth, flush, and invisible on exposed faces.

c. Install frames with removable glazing stops located on secure side of opening. d. Install door silencers in frames before grouting. e. Remove temporary braces necessary for installation only after frames have been

properly set and secured. f. Check plumbness, squareness, and twist of frames as walls are constructed. Shim as

necessary to comply with installation tolerances. g. Field apply bituminous coating to backs of frames that are filled with grout containing

antifreezing agents.

2. Floor Anchors: Provide floor anchors for each jamb and mullion that extends to floor, and secure with postinstalled expansion anchors.

a. Floor anchors may be set with powder-actuated fasteners instead of postinstalled expansion anchors if so indicated and approved on Shop Drawings.

3. Metal-Stud Partitions: Solidly pack mineral-fiber insulation behind frames. 4. Masonry Walls: Coordinate installation of frames to allow for solidly filling space between

frames and masonry with grout. 5. Concrete Walls: Solidly fill space between frames and concrete with grout. Take precautions,

including bracing frames, to ensure that frames are not deformed or damaged by grout forces. 6. Ceiling Struts: Extend struts vertically from top of frame at each jamb to overhead structural

supports or substrates above frame unless frame is anchored to masonry or to other structural support at each jamb. Bend top of struts to provide flush contact for securing to supporting construction. Provide adjustable wedged or bolted anchorage to frame jamb members.

7. Installation Tolerances: Adjust hollow metal door frames for squareness, alignment, twist, and plumb to the following tolerances:

a. Squareness: Plus or minus 1/16 inch, measured at door rabbet on a line 90 degrees from jamb perpendicular to frame head.

b. Alignment: Plus or minus 1/16 inch, measured at jambs on a horizontal line parallel to plane of wall.

c. Twist: Plus or minus 1/16 inch, measured at opposite face corners of jambs on parallel lines, and perpendicular to plane of wall.

d. Plumbness: Plus or minus 1/16 inch, measured at jambs at floor.

B. Hollow Metal Doors: Fit hollow metal doors accurately in frames, within clearances specified below. Shim as necessary.

1. Non-Fire-Rated Standard Steel Doors:



a. Jambs and Head: 1/8 inch plus or minus 1/16 inch. b. Between Edges of Pairs of Doors: 1/8 inch plus or minus 1/16 inch. c. Between Bottom of Door and Top of Threshold: Maximum 3/8 inch. d. Between Bottom of Door and Top of Finish Floor (No Threshold): Maximum 3/4 inch.

2. Fire-Rated Doors: Install doors with clearances according to NFPA 80. 3. Smoke-Control Doors: Install doors according to NFPA 105.

C. Glazing: Comply with installation requirements in Division 08 Section "Glazing" and with hollow metal manufacturer's written instructions.

1. Secure stops with countersunk flat- or oval-head machine screws spaced uniformly not more than 9 inches o.c. and not more than 2 inches o.c. from each corner.

3.2 ADJUSTING AND CLEANING

A. Final Adjustments: Check and readjust operating hardware items immediately before final inspection. Leave work in complete and proper operating condition. Remove and replace defective work, including hollow metal work that is warped, bowed, or otherwise unacceptable.

B. Prime-Coat Touchup: Immediately after erection, sand smooth rusted or damaged areas of prime coat and apply touchup of compatible air-drying, rust-inhibitive primer.

C. Metallic-Coated Surfaces: Clean abraded areas and repair with galvanizing repair paint according to manufacturer's written instructions.

END OF SECTION 081113


FLUSH WOOD DOORS 081416 1

SECTION 081416 - FLUSH WOOD DOORS

PART 1 - GENERAL

1.1 SUMMARY


1. Solid-core doors with wood-veneer or plastic-laminate faces.

B. Related Sections:

1. Division 08 Section "Glazing" for glass view panels in flush wood doors.

1.2 SUBMITTALS

A. Product Data: For each type of door indicated.

B. Shop Drawings: Indicate location, size, and hand of each door; elevation of each kind of door; construction details not covered in Product Data; location and extent of hardware blocking; and other pertinent data.

1. Indicate dimensions and locations of mortises and holes for hardware. 2. Indicate dimensions and locations of cutouts. 3. Indicate requirements for veneer matching. 4. Indicate doors to be factory finished and finish requirements. 5. Indicate fire-protection ratings for fire-rated doors.

C. Samples: For plastic-laminate door faces and factory-finished doors.


A. Manufacturer Qualifications: A qualified manufacturer that is certified for chain of custody by an FSC-accredited certification body.

B. Quality Standard: In addition to requirements specified, comply with AWI's "Architectural Woodwork Quality Standards Illustrated."

C. Fire-Rated Wood Doors: Doors complying with NFPA 80 that are listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at positive pressure according to UL 10B.

PART 2 - PRODUCTS

2.1 MANUFACTURERS


1. Algoma Hardwoods, Inc. 2. Ampco, Inc.



3. Buell Door Company Inc. 4. Chappell Door Co. 5. Eagle Plywood & Door Manufacturing, Inc. 6. Eggers Industries. 7. Graham; an Assa Abloy Group company. 8. Haley Brothers, Inc. 9. Ideal Architectural Doors & Plywood. 10. Ipik Door Company. 11. Lambton Doors. 12. Marlite. 13. Marshfield Door Systems, Inc. 14. Mohawk Flush Doors, Inc.; a Masonite company. 15. Oshkosh Architectural Door Company. 16. Poncraft Door Company. 17. Vancouver Door Company. 18. VT Industries Inc.

2.2 DOOR CONSTRUCTION, GENERAL

A. Low-Emitting Materials: Provide doors made with adhesives and composite wood products that do not contain urea formaldehyde.

B. WDMA I.S.1-A Performance Grade:

1. Heavy Duty unless otherwise indicated.

C. Particleboard-Core Doors:

1. Particleboard: ANSI A208.1, made with binder containing no urea-formaldehyde resin. 2. Provide doors with either glued-wood-stave or structural-composite-lumber cores instead of

particleboard cores for doors indicated to receive exit devices.

D. Structural-Composite-Lumber-Core Doors:

1. Structural Composite Lumber: WDMA I.S.10.

a. Screw Withdrawal, Face: 700 lbf. b. Screw Withdrawal, Edge: 400 lbf.

E. Fire-Protection-Rated Doors: Provide core specified or mineral core as needed to provide fire-protection rating indicated.

1. Edge Construction: Provide edge construction with intumescent seals concealed by outer stile. Comply with specified requirements for exposed edges.

2. Pairs: Provide fire-retardant stiles that are listed and labeled for applications indicated without formed-steel edges and astragals. Provide stiles with concealed intumescent seals. Comply with specified requirements for exposed edges.

F. Mineral-Core Doors:

1. Core: Noncombustible mineral product complying with requirements of referenced quality standard and testing and inspecting agency for fire-protection rating indicated.

2. Blocking: Provide composite blocking with improved screw-holding capability approved for use in doors of fire-protection ratings indicated as needed to eliminate through-bolting hardware.

3. Edge Construction: At hinge stiles, provide laminated-edge construction with improved screw-holding capability and split resistance. Comply with specified requirements for exposed edges.



2.3 VENEERED-FACED DOORS FOR TRANSPARENT FINISH

A. Interior Solid-Core Doors:

1. Grade: Premium, with Grade AA faces. 2. Species: as indicated. 3. Cut: Plain sliced (flat sliced). 4. Match between Veneer Leaves: Pleasing match. 5. Assembly of Veneer Leaves on Door Faces: Balance match. 6. Pair and Set Match: Provide for doors hung in same opening or separated only by mullions. 7. Core: Particleboard. 8. Construction: Five or seven plies. Stiles and rails are bonded to core, then entire unit abrasive

planed before veneering. 9. Construction: Seven plies, either bonded or nonbonded construction.

2.4 PLASTIC-LAMINATE-FACED DOORS

A. Interior Solid-Core Doors:

1. Grade: Premium. 2. Plastic-Laminate Faces: High-pressure decorative laminates complying with NEMA LD 3,

Grade HGS. 3. Colors, Patterns, and Finishes: As selected by Architect from laminate manufacturer's full

range of products. 4. Exposed Vertical Edges: Hardwood edges for painting. 5. Core: Particleboard. 6. Construction: Three plies. Stiles and rails are bonded to core, then entire unit abrasive planed

before faces are applied. 7. Construction: Five plies. Stiles and rails are bonded to core, then entire unit abrasive planed

before faces and crossbands are applied.

2.5 LOUVERS AND LIGHT FRAMES

A. Metal Louvers: 1. Metal and Finish: Extruded aluminum with Class II, clear anodic finish, AA-M12C22A31.

B. Metal Frames for Light Openings in Fire-Rated Doors: Manufacturer's standard frame formed of 0.048-inch- thick, cold-rolled steel sheet; with baked-enamel- or powder-coated finish; and approved for use in doors of fire-protection rating indicated.

2.6 FABRICATION

A. Factory fit doors to suit frame-opening sizes indicated. Comply with clearance requirements of referenced quality standard for fitting unless otherwise indicated.

1. Comply with requirements in NFPA 80 for fire-rated doors.

B. Factory machine doors for hardware that is not surface applied.

C. Openings: Cut and trim openings through doors in factory.

1. Light Openings: Trim openings with moldings of material and profile indicated. 2. Glazing: Factory install glazing in doors indicated to be factory finished. Comply with

applicable requirements in Division 08 Section "Glazing."



3. Louvers: Factory install louvers in prepared openings.

2.7 SHOP PRIMING

A. Doors for Opaque Finish: Shop prime doors with one coat of wood primer specified in Division 09 Section "Interior Painting". Seal all four edges, edges of cutouts, and mortises with primer.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Hardware: For installation, see Division 08 Section "Door Hardware."

B. Installation Instructions: Install doors to comply with manufacturer's written instructions and the referenced quality standard, and as indicated.

1. Install fire-rated doors in corresponding fire-rated frames according to NFPA 80.

C. Job-Fitted Doors: Align and fit doors in frames with uniform clearances and bevels; do not trim stiles and rails in excess of limits set by manufacturer or permitted for fire-rated doors. Machine doors for hardware. Seal edges of doors, edges of cutouts, and mortises after fitting and machining.

1. Clearances: Provide 1/8 inch at heads, jambs, and between pairs of doors. Provide 1/8 inch from bottom of door to top of decorative floor finish or covering unless otherwise indicated. Where threshold is shown or scheduled, provide 1/4 inch from bottom of door to top of threshold unless otherwise indicated.

a. Comply with NFPA 80 for fire-rated doors.

D. Factory-Fitted Doors: Align in frames for uniform clearance at each edge.

E. Factory-Finished Doors: Restore finish before installation if fitting or machining is required at Project site.



OVERHEAD COILING DOORS 083323 1

SECTION 083323 - OVERHEAD COILING DOORS

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes:

1. Service doors. 2. Insulated service doors. 3. Fire-rated service doors. 4. Fire-rated, insulated service doors. 5. Fire-rated counter doors.

B. Related Section:

1. Division 05 Section "Metal Fabrications" for miscellaneous steel supports.

1.2 PERFORMANCE REQUIREMENTS

A. Structural Performance, Exterior Doors: Exterior overhead coiling doors shall withstand the wind loads, the effects of gravity loads, and loads and stresses within limits and under conditions indicated according to SEI/ASCE 7.

1. Wind Loads: Per General Structural Notes.

B. Windborne-Debris-Impact-Resistance Performance: Provide and impact-protective overhead coiling doors that pass missile-impact and cyclic-pressure tests when tested according to ASTM E 1886 and ASTM E 1996.

1. Large Missile Test: For overhead coiling doors located within 30 feet of grade. 2. Small Missile Test: For overhead coiling doors located more than 30 feet above grade.

C. Seismic Performance: Overhead coiling doors shall withstand the effects of earthquake motions determined according to SEI/ASCE 7.

1.3 SUBMITTALS

A. Product Data: For each type and size of overhead coiling door and accessory.

B. Shop Drawings: For each installation and for special components not dimensioned or detailed in manufacturer's product data. Include plans, elevations, sections, details, and attachments to other work.

1. Detail equipment assemblies and indicate dimensions, weights, loads, required clearances, method of field assembly, components, and location and size of each field connection.

2. Show locations of replaceable fusible links. 3. Wiring Diagrams: For power, signal, and control wiring.

C. Seismic Qualification Certificates: For overhead coiling doors, accessories, and components, from manufacturer.



D. Oversize Construction Certification: For door assemblies required to be fire-rated and that exceed size limitations of labeled assemblies.

E. Maintenance Data.


A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved for both installation and maintenance of units required for this Project.

B. Fire-Rated Door Assemblies: Assemblies complying with NFPA 80 that are listed and labeled by a qualified testing agency, for fire-protection ratings indicated, based on testing at as close to neutral pressure as possible according to UL 10B.

C. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

PART 2 - PRODUCTS

2.1 DOOR CURTAIN MATERIALS AND CONSTRUCTION

A. Door Curtains: Fabricate overhead coiling-door curtain of interlocking metal slats, designed to withstand wind loading indicated, in a continuous length for width of door without splices. Unless otherwise indicated, provide slats of thickness and mechanical properties recommended by door manufacturer for performance, size, and type of door indicated, and as follows: 1. Insulation: Fill slats for insulated doors with manufacturer's standard thermal insulation

complying with maximum flame-spread and smoke-developed indexes of 75 and 450, respectively, according to ASTM E 84. Enclose insulation completely within slat faces.

2. Metal Interior Curtain-Slat Facing: Match metal of exterior curtain-slat face.

B. Bottom Bar for Service Doors: Consisting of two angles, each not less than 1-1/2 by 1-1/2 by 1/8 inch thick; fabricated from metal to match curtain slats and finish.

C. Curtain Jamb Guides: Manufacturer's standard angles or channels and angles of same material and finish as curtain slats unless otherwise indicated, with sufficient depth and strength to retain curtain, to allow curtain to operate smoothly, and to withstand loading. Slot bolt holes for guide adjustment. Provide removable stops on guides to prevent overtravel of curtain.

1. Removable Posts and Jamb Guides for Counter Doors: Manufacturer's standard.

2.2 HOOD

A. General: Form sheet metal hood to entirely enclose coiled curtain and operating mechanism at opening head. Contour to fit end brackets to which hood is attached. Roll and reinforce top and bottom edges for stiffness. Form closed ends for surface-mounted hoods and fascia for any portion of between-jamb mounting that projects beyond wall face. Equip hood with intermediate support brackets as required to prevent sagging.

1. Include automatic drop baffle on fire-rated doors to guard against passage of smoke or flame. 2. Exterior-Mounted Doors: Fabricate hood to act as weather protection and with a perimeter

sealant-joint-bead profile for applying joint sealant.



2.3 LOCKING DEVICES

A. Slide Bolt: Fabricate with side-locking bolts to engage through slots in tracks for locking by padlock, located on both left and right jamb sides, operable from coil side.

B. Locking Device Assembly: Fabricate with cylinder lock, spring-loaded dead bolt, operating handle, cam plate, and adjustable locking bars to engage through slots in tracks.

1. Lock Cylinders: Provide cylinders and keyed to building keying system. 2. Keys: Provide Three for each cylinder.

C. Chain Lock Keeper: Suitable for padlock.

D. Safety Interlock Switch: Equip power-operated doors with safety interlock switch to disengage power supply when door is locked.

2.4 CURTAIN ACCESSORIES

A. Smoke Seals: Equip each fire-rated door with smoke-seal perimeter gaskets for smoke and draft control as required for door listing and labeling by a qualified testing agency.

B. Weatherseals: Equip each exterior door with weather-stripping gaskets fitted to entire perimeter of door for a weathertight installation, unless otherwise indicated.

C. Push/Pull Handles: Equip each push-up-operated or emergency-operated door with lifting handles on each side of door, finished to match door. Provide pull-down straps or pole hooks for doors more than 84 inches high.

D. Automatic-Closing Device for Fire-Rated Doors: Equip each fire-rated door with an automatic-closing device that is inoperative during normal door operations and that has a governor unit complying with NFPA 80 and an easily tested and reset release mechanism designed to be activated by the following:

1. Replaceable fusible links with temperature rise and melting point of 165 deg F interconnected and mounted on both sides of door opening.

2. Manufacturer's standard UL-labeled smoke detector and door-holder-release devices. 3. Manufacturer's standard UL-labeled heat detector and door-holder-release devices. 4. Building fire-detection and -alarm systems and manufacturer's standard door-holder-release

devices.

2.5 COUNTERBALANCING MECHANISM

A. General: Counterbalance doors by means of manufacturer's standard mechanism with an adjustable-tension, steel helical torsion spring mounted around a steel shaft and contained in a spring barrel connected to top of curtain with barrel rings. Use grease-sealed bearings or self-lubricating graphite bearings for rotating members.

B. Brackets: Manufacturer's standard mounting brackets of either cast iron or cold-rolled steel plate.

2.6 MANUAL DOOR OPERATORS

A. Equip door with manufacturer's recommended manual door operator unless another type of door operator is indicated.



B. Push-up Door Operation: Design counterbalance mechanism so required lift or pull for door operation does not exceed 25 lbf.

C. Chain-Hoist Operator: Consisting of endless steel hand chain, chain-pocket wheel and guard, and gear-reduction unit with a maximum 25 lbf force for door operation. Provide alloy-steel hand chain with chain holder secured to operator guide.

2.7 ELECTRIC DOOR OPERATORS

A. General: Electric door operator assembly of size and capacity recommended and provided by door manufacturer for door and operation-cycles requirement specified, with electric motor and factory-prewired motor controls, starter, gear-reduction unit, solenoid-operated brake, clutch, remote-control stations, control devices, integral gearing for locking door, and accessories required for proper operation.

1. Comply with NFPA 70. 2. Provide control equipment complying with NEMA ICS 1, NEMA ICS 2, and NEMA ICS 6, with

NFPA 70 Class 2 control circuit, maximum 24 V, ac or dc.

B. Usage Classification: Electric operator and components capable of operating for not less than number of cycles per hour indicated for each door.

C. Electric Motors: Comply with NEMA designation, temperature rating, service factor, enclosure type, and efficiency requirements specified in Division 11 Section "Common Motor Requirements for Equipment" unless otherwise indicated.

1. Electrical Characteristics:

a. Phase: As indicated. b. Volts: As indicated. c. Hertz: 60.

2. Motor Type and Controller: Reversible motor and controller (disconnect switch) for motor exposure indicated.

3. Motor Size: Minimum size as indicated. If not indicated, large enough to start, accelerate, and operate door in either direction from any position, at a speed not less than 8 in./sec. and not more than 12 in./sec., without exceeding nameplate ratings or service factor.

4. Operating Controls, Controllers (Disconnect Switches), Wiring Devices, and Wiring: Manufacturer's standard unless otherwise indicated.

D. Obstruction Detection Device: Equip motorized door with indicated external automatic safety sensor capable of protecting full width of door opening. For non-fire-rated doors, activation of device immediately stops and reverses downward door travel. For fire-rated doors, activation delays closing. 1. Sensor Edge: Automatic safety sensor edge, located within astragal or weather stripping

mounted to bottom bar. Contact with sensor activates device. Connect to control circuit using manufacturer's standard take-up reel or self-coiling cable. Provide self-monitoring capability designed to interface with door operator control circuit to detect damage to or disconnection of sensing device.

E. Emergency Manual Operation: Equip each electrically powered door with capability for emergency manual operation. Design manual mechanism so required force for door operation does not exceed 25 lbf.

F. Emergency Operation Disconnect Device: Equip operator with hand-operated disconnect mechanism for automatically engaging manual operator and releasing brake for emergency manual operation while disconnecting motor without affecting timing of limit switch. Mount mechanism so it is accessible



from floor level. Include interlock device to automatically prevent motor from operating when emergency operator is engaged.

G. Motor Removal: Design operator so motor may be removed without disturbing limit-switch adjustment and without affecting emergency manual operation.

H. Audible and Visual Signals: Audible alarm and visual indicator lights in compliance with regulatory requirements for accessibility.

2.8 DOOR ASSEMBLY

A. Service, Insulated Service and Counter Door: Overhead fire-rated coiling door formed with curtain of interlocking metal slats.

1. Manufacturers: Subject to compliance with requirements, available manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

a. ACME Rolling Doors. b. Alpine Overhead Doors, Inc. c. AlumaTek, Inc. d. C.H.I. Overhead Doors. e. City-Gates. f. Cookson Company. g. Cornell Iron Works, Inc. h. Dynamic Closures Corp. i. Lawrence Roll-Up Doors, Inc. j. Mahon Door Corporation. k. McKeon Rolling Steel Door Company, Inc. l. Metro Door. m. Overhead Door Corporation. n. QMI Security Solutions. o. Raynor. p. Southwestern Steel Rolling Door Co. q. Wayne-Dalton Corp. r. Windsor Door.

B. Operation Cycles: Not less than 100,000.

C. Fire Rating: As indicated.

D. Curtain R-Value: 4.5 deg F x h x sq. ft./Btu.

E. Door Curtain Material: Galvanized steel.

F. Door Curtain Slats: Curved profile slats of 1-1/2-inch center-to-center height. 1. Fenestrated Slats: Approximately 10- by 1-5/8-inch openings, spaced approximately 1-1/2

inches apart and beginning 12 inches from jamb guides. 2. Insulated-Slat Interior Facing: Metal.

G. Curtain Jamb Guides: Aluminum with exposed finish matching curtain slats. Provide continuous integral wear strips to prevent metal-to-metal contact and to minimize operational noise.

H. Hood: Match curtain material and finish

1. Shape: Round. 2. Mounting: Face of wall.



I. Locking Devices: Equip door with locking device assembly and chain lock keeper.

1. Locking Device Assembly: Single-jamb side locking bars, operable from inside with thumb turn.

J. Manual Door Operator: Chain-hoist operator.

1. Provide operator with through-wall shaft operation. 2. Provide operator with manufacturer's standard removable operating arm.

K. Electric Door Operator:

1. Usage Classification: Medium duty, up to 15 cycles per hour. 2. Motor Exposure: Interior. 3. Emergency Manual Operation: Chain type. 4. Obstruction-Detection Device: Automatic electric sensor edge on bottom bar.

L. Door Finish: 1. Baked-Enamel or Powder-Coated Finish: Color as selected by Architect from manufacturer's

full range. 2. Factory Prime Finish: Manufacturer's standard color. 3. Interior Curtain-Slat Facing: Match finish of exterior curtain-slat face.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install overhead coiling doors and operating equipment complete with necessary hardware, anchors, inserts, hangers, and equipment supports; according to manufacturer's written instructions and as specified.

B. Fire-Rated Doors: Install according to NFPA 80.

C. Smoke-Control Doors: Install according to NFPA 80 and NFPA 105.

D. Adjust hardware and moving parts to function smoothly so that doors operate easily, free of warp, twist, or distortion. Lubricate bearings and sliding parts as recommended by manufacturer. Adjust seals to provide weathertight fit around entire perimeter.

3.2 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain overhead coiling doors.



HIGH SPEED ROLLING DOORS 083325 1

SECTION 083325 - HIGH SPEED ROLLING DOORS PART 1 - GENERAL

1.01 SECTION INCLUDES

A. High-speed roll-up doors.

B. Wiring from electric circuit disconnect to operator to control station.

1.02 RELATED SECTIONS

A. None

1.03 REFERENCES

A. NEMA - National Electrical Manufacturers Association.

B. LED - Light Emitting Diode.

1.04 SYSTEM DESCRIPTION

A. Motor type: AC drive, and variable speed with soft acceleration and braking. Mechanical release lever on side column allows door to be easily opened in the event of a power failure.

1.05 SUBMITTALS

A. Submit the following:

1. Shop Drawings: Indicate pertinent dimensioning, anchorage methods, hardware locations, and

installation details.

2. Product Data: Provide general construction, component connections and details, and electrical equipment, operation instructions, and information.

3. Samples: Submit samples of door slat material.

4. Manufacturer's Installation: Indicate installation sequence and procedures, adjustment, and

alignment procedures.

1.06 MAINTENANCE DATA

A. Scheduled maintenance program available to include lubrication requirements and frequency, periodic adjustments required, scheduled maintenance suggested, manufacturer’s data sheets, and equipment inter-connection diagrams.

1.07 REGULATORY REQUIREMENTS

A. Electrical components UL listed. B. Electrical control panel NEMA approved.


A. Furnish high-speed roll doors and all components and accessories by one manufacturer.



B. Specific door model used must have a proven track record of successful installations in similar

applications of no less than 3 years. References to be provided upon request.

1.09 FIELD MEASUREMENTS

A. Verify field measurements are as indicated on shop drawings.

1.10 COORDINATION

A. Coordinate the work with installation of electric power and locations and sizes of conduit.

1.11 WARRANTY

A. Five-year limited warranty on mechanical components B. Two-year limited warranty on electrical components

PART 2 - PRODUCTS

2.01 PRODUCTS

A. Rytec Corporation Spiral FV B. No substitutions permitted

2.02 MATERIALS

A. Door Panel: aluminum slat frames with 9” high LEXAN clear premium polycarbonate windows with

performance coating. Thickness of slats ranges from 1.2” – 2.4”, depending on overall size of door. Integral rubber weatherseal between each slat. Door slats are connected by hinge system to provide additional rigidity and security to door panel. Door curtain does not require a tensioning system for additional wind/pressure resistance. Doors which require the use of a tensioning system for additional wind/pressure resistance will not be accepted.

B. Side Frames: Galvanized steel side frames with full height weatherseal on both sides to seal against

door panel. Dual thru-beam photo-eyes mounted within door jamb. Doors using an external coil cord will not be accepted.

C. Hood Covers: Front & Bottom Head Covers to enclose door header (optional).

D. Bottom Bar: Extruded aluminum bottom bar with electric, reversing edge that reverses the door upon

contacting an object.

E. Counterbalance: Up to six extension springs in each side column, depending on the size of the door. Springs assist the motor in opening the door. Mechanical release lever on side column allows door to be easily opened in the event of a power failure. Doors using torsion springs for counterbalance or doors with springs located within a barrel will not be accepted.

F. Drive system: Minimum 2 HP motor with variable speed AC drive which allows for soft acceleration and

braking. Doors using a motor with a clutch or pump will not be accepted.

G. Travel Speed: Opens at up to 100 inches per second and closes at lower speed.

H. Electrical Controls 1. Rytec controller housed in a UL/cUL Listed NEMA 4X-rated enclosure with factory set

parameters. 2. Parameter changes and all door configurations can be made from the face of the control box,

no exposure to high voltage. Control panels that require opening of the control box and reaching inside to make parameter changes will not be accepted.



3. Controls include a variable speed AC drive system capable of infinitely variable speed control in both directions.

4. Programmable inputs and outputs accommodate special control applications (traffic lights, horns, actuation devices, timing sequences, etc.) without the need for additional electrical components.

5. Self-diagnostic scrolling two-line vacuum fluorescent display provides expanded informational messages for straightforward installation, control adjustments and error reporting.

6. Complete history of door, at least two years, is logged and encrypted onto a USB flash drive. All errors have a time and date stamp for reference. Control panels not logging up to two years of door history will not be accepted.

7. Provide BEA IS40 Motion/Presence Sensors for activation 8. Provide On/Off Selector Switch on face of control box to disable motion sensors after hours

I. Door to use rotary encoder to regulate door travel limits. Limits to be self-adjusting, without the use of

tools, from floor level at the control panel. Doors using mechanical limits switches or doors that require tools to set the limits will not be accepted.

J. Door Track: Spiral rollup design features not metal-to-metal contact which results in whisper-quiet, low

maintenance operation and eliminates wear on panel slats. Doors that roll up on a barrel or whose track design allows metal-to-metal contact will not be accepted.

K. Windload: Door testing indicates the door is capable of withstanding winds up to and exceeding 75 mph

(14 psf).

L. All components factory finished. PART 3 - EXECUTION

3.01 EXAMINATION

A. Verify that opening sizes, tolerances, and conditions are acceptable.

3.02 INSTALLATION

A. Install door unit assembly in accordance with manufacturer's instructions.

B. Use anchorage devices to securely fasten assembly to wall construction and building framing without distortion or stress.

C. Fit and align assembly including hardware; level to plumb to provide smooth operation.

D. Coordinate installation of electrical service. Complete wiring from disconnect to unit components.

3.03 ADJUSTING

A. Adjust door and operating assemblies.

B. Test and adjust door(s), if necessary, for proper operation.

3.04 CLEANING

A. Clean door and components. Use caution when cleaning acrylic and polycarbonate windows.



OVERHEAD COILING GRILLES 083326 - 1

SECTION 083326 - OVERHEAD COILING GRILLES

PART 1 - GENERAL

1.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.

1.2 SUMMARY

A. Section includes open-curtain overhead coiling grilles.

B. Related Section:



A. Seismic Performance: Overhead coiling grilles shall withstand the effects of earthquake motions determined according to SEI/ASCE 7.

1.4 SUBMITTALS

A. Product Data: For each type and size of overhead coiling grille and accessory.


1. Detail equipment assemblies and indicate dimensions, weights, loads, required clearances, method of field assembly, components, and location and size of each field connection.

2. Wiring Diagrams: For power, signal, and control wiring.

C. Samples: For each exposed product and for each color and texture specified.

D. Seismic Qualification Certificates: For overhead coiling grilles, accessories, and components, from manufacturer.

E. Maintenance data.





B. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

PART 2 - PRODUCTS

2.1 GENERAL

A. To every extent possible, use building materials or products which have been extracted, harvested or recovered, as well as manufactured, within 500 miles of the project site.

B. To every extent possible, use materials with high recycled content.

2.2 GRILLE CURTAIN MATERIALS AND CONSTRUCTION

A. Open-Curtain Grilles: Fabricate metal grille curtain as an open network of horizontal rods, spaced at regular intervals, that are interconnected with vertical links, which are formed and spaced as indicated and are free to rotate on the rods.

B. Bottom Bar: Manufacturer's standard continuous channel or tubular shape, finished to match grille.

1. Astragal: Equip each grille bottom bar with a replaceable, adjustable, continuous, compressible gasket of flexible vinyl, rubber, or neoprene as a cushion bumper.

2. Provide motor-operated grilles with combination bottom astragal and sensor edge.

C. Grille Curtain Jamb Guides: Manufacturer's standard shape having curtain groove with return lips or bars to retain curtain. Provide continuous integral wear strips to prevent metal-to-metal contact and to minimize operational noise; with removable stops on guides to prevent overtravel of curtain.

1. Removable Posts and Jamb Guides: Manufacturer's standard.

2.3 HOODS AND ACCESSORIES

A. General: Form sheet metal hood to entirely enclose coiled curtain and operating mechanism at opening head. Contour to fit end brackets to which hood is attached. Roll and reinforce top and bottom edges for stiffness. Form closed ends for surface-mounted hoods and fascia for any portion of between-jamb mounting that projects beyond wall face. Equip hood with intermediate support brackets as required to prevent sagging.

1. Removable Metal Soffit: Of same material and finish as curtain if hood is mounted above ceiling, unless otherwise indicated.

B. Mounting Frame: Manufacturer's standard mounting frame designed to support grille; factory fabricated from ASTM A 36/A 36M structural-steel tubes or shapes, hot-dip galvanized per ASTM A 123/A 123M; fastened to floor and structure above grille; to be built into wall construction; and complete with anchors, connections, and fasteners.

C. Push/Pull Handles: Equip each push-up-operated or emergency-operated grille with lifting handles on each side of grille, finished to match grille. Provide pull-down straps or pole hooks for grilles more than 84 inches (2130 mm) high.



2.4 LOCKING DEVICES

A. Locking Device Assembly: Fabricate with cylinder lock, spring-loaded dead bolt, operating handle, cam plate, and adjustable locking bars to engage through slots in tracks.

1. Lock Cylinders: Provide cylinders specified in Division 08 Section "Door Hardware." and keyed to building keying system.

2. Keys: Three for each cylinder.

B. Safety Interlock Switch: Equip power-operated grilles with safety interlock switch to disengage power supply when grille is locked.

2.5 COUNTERBALANCING MECHANISM

A. General: Counterbalance grilles by means of manufacturer's standard mechanism with an adjustable-tension, steel helical torsion spring mounted around a steel shaft and contained in a spring barrel connected to top of curtain with barrel rings. Use grease-sealed bearings or self-lubricating graphite bearings for rotating members.

B. Brackets: Manufacturer's standard mounting brackets of either cast iron or cold-rolled steel plate.

2.6 ELECTRIC GRILLE OPERATORS

A. General: Electric grille operator assembly of size and capacity recommended and provided by grille manufacturer for grille and operation-cycles requirement specified, with electric motor and factory-prewired motor controls, starter, gear-reduction unit, solenoid-operated brake, clutch, remote-control stations, control devices, integral gearing for locking grille, and accessories required for proper operation.

1. Comply with NFPA 70. 2. Provide control equipment complying with NEMA ICS 1, NEMA ICS 2, and NEMA ICS 6,

with NFPA 70 Class 2 control circuit, maximum 24 V, ac or dc.

B. Usage Classification: Electric operator and components capable of operating for not less than number of cycles per hour indicated for each grille.

C. Electric Motors: Comply with NEMA designation, temperature rating, service factor, enclosure type, and efficiency requirements specified in Division 11 Section "Common Motor Requirements for Equipment" unless otherwise indicated.


a. Phase: as indicated. b. Volts: as indicated. c. Hertz: 60.


3. Motor Size: Minimum size as indicated. If not indicated, large enough to start, accelerate, and operate grille in either direction from any position, at a speed not less than 8 in./sec. (203 mm/s) and not more than 12 in./sec. (305 mm/s), without exceeding nameplate ratings or service factor.




D. Obstruction Detection Device: Equip motorized grille with indicated external automatic safety sensor capable of protecting full width of grille opening. Activation of sensor immediately stops and reverses downward grille travel.

1. Photoelectric Sensor: Manufacturer's standard system designed to detect an obstruction in grille opening without contact between grille and obstruction.

2. Sensor Edge: Automatic safety sensor edge, located within astragal or weather stripping mounted to bottom bar. Contact with sensor activates device. Connect to control circuit using manufacturer's standard take-up reel or self-coiling cable.

E. Remote-Control Station: Momentary-contact, three-button control station with push-button controls labeled "Open," "Close," and "Stop"; interior units, full-guarded, surface-mounted, heavy-duty type, with general-purpose NEMA ICS 6, Type 1 enclosure.

F. Emergency Manual Operation: Equip each electrically powered grille with capability for emergency manual operation. Design manual mechanism so required force for grille operation does not exceed 25 lbf (111 N).

G. Emergency Operation Disconnect Device: Equip operator with hand-operated disconnect mechanism for automatically engaging manual operator and releasing brake for emergency manual operation while disconnecting motor without affecting timing of limit switch. Mount mechanism so it is accessible from floor level. Include interlock device to automatically prevent motor from operating when emergency operator is engaged.

H. Motor Removal: Design operator so motor may be removed without disturbing limit-switch adjustment and without affecting emergency manual operation.

I. Audible and Visual Signals: Audible alarm and visual indicator lights in compliance with regulatory requirements for accessibility.

J. Emergency-Egress Release: Flush, wall-mounted handle mechanism, for ADA-ABA-compliant egress feature, not dependent on electric power. The release allows an unlocked grille to partially open without affecting limit switches to permit passage, and it automatically resets motor drive upon return of handle to original position.

2.7 OPEN-CURTAIN GRILLE ASSEMBLY

A. Open-Curtain Grille: Overhead coiling grille with a curtain having a network of horizontal rods that interconnect with vertical links.


a. ACME Rolling Doors. b. Alpine Overhead Doors, Inc. c. AlumaTek, Inc. d. City-Gates. e. Cookson Company. f. Cornell Iron Works, Inc. g. Dynaflair Corporation.



h. Dynamic Closures Corp. i. Lawrence Roll-Up Doors, Inc. j. Mahon Door Corporation. k. McKeon Rolling Steel Door Company, Inc. l. Metro Door. m. Overhead Door Corporation. n. Raynor. o. Windsor Door.


C. Grille Curtain Material: Aluminum.

1. Space rods at approximately 3 inches (76 mm) o.c. 2. Space links approximately 6 inches (152 mm) apart in a straight in-line pattern. 3. Spacers: Metal tubes matching curtain material.

D. Curtain Jamb Guides: Aluminum with exposed finish matching curtain slats. Provide continuous integral wear strips to prevent metal-to-metal contact and to minimize operational noise.

E. Locking Devices: Equip grille with locking device assembly.

1. Locking Device Assembly: Single-jamb side locking bars, operable fromoutside with cylinder.

F. Electric Grille Operator:

1. Usage Classification: Light duty, up to 10 cycles per hour. 2. Emergency Manual Operation: Push-up type. 3. Obstruction-Detection Device: Automatic electric sensor edge on bottom bar.

G. Grille Finish:

1. Aluminum Finish: Mill

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install overhead coiling grilles and operating equipment complete with necessary hardware, anchors, inserts, hangers, and equipment supports; according to manufacturer's written instructions and as specified.

B. Adjust hardware and moving parts to function smoothly so that grilles operate easily, free of warp, twist, or distortion. Lubricate bearings and sliding parts as recommended by manufacturer.

3.2 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain overhead coiling grilles.





SECTIONAL DOORS 083613 1

SECTION 083613 - SECTIONAL DOORS

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes electrically operated sectional doors.

B. Related Section:



A. General Performance: Sectional doors shall meet performance requirements specified without failure due to defective manufacture, fabrication, installation, or other defects in construction and without requiring temporary installation of reinforcing components.

B. Delegated Design: Design sectional doors, including comprehensive engineering analysis by a qualified professional engineer, using performance requirements and design criteria indicated.

C. Structural Performance: Exterior sectional doors shall withstand the effects of gravity loads, and the following loads and stresses within limits and under conditions indicated according to ASCE/SEI 7.

1. Wind Loads: Per General Structural Notes.

D. Air Infiltration: Maximum rate not more than indicated when tested according to ASTM E 283.

1. Air Infiltration: Maximum rate of 0.08 cfm/sq. ft. at 15 and 25 mph.

E. Windborne-Debris-Impact-Resistance Performance: Provide glazed sectional doors that pass large-missile-impact and cyclic-pressure tests when tested according to ASTM E 1886 and ASTM E 1996.

F. Seismic Performance: Sectional doors shall withstand the effects of earthquake motions determined according to ASCE/SEI 7.

1.3 SUBMITTALS

A. Product Data: For each type and size of sectional door and accessory.


C. Samples: For each exposed product and for each color and texture specified.

D. Delegated-Design Submittal: For sectional doors indicated to comply with performance requirements and design criteria, including analysis data signed and sealed by the qualified professional engineer responsible for their preparation.

E. Seismic Qualification Certificates: For sectional doors, accessories, and components, from manufacturer.



F. Maintenance data.

G. Warranties: Sample of special warranties.



B. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, by a qualified testing agency, and marked for intended location and application.

C. Standard for Sectional Doors: Fabricate sectional doors to comply with DASMA 102 unless otherwise indicated.

1.5 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of sectional doors that fail in materials or workmanship within specified warranty period.

1. Warranty Period: Five years from date of Substantial Completion.

B. Special Finish Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components that show evidence of deterioration of factory-applied finishes within specified warranty period.

1. Warranty Period: 10 years from date of Substantial Completion.

PART 2 - PRODUCTS

2.1 ALUMINUM DOOR SECTIONS

A. Sections: Construct door sections with stiles and rails formed from extruded-aluminum shapes. Fabricate sections with stile and rail dimensions and profiles shown on Drawings. Join stiles and rails by welding or with concealed aluminum or nonmagnetic stainless-steel through bolts, full height of door section. Form meeting rails to provide a weathertight-seal joint.

1. Reinforce sections with continuous horizontal and diagonal reinforcement, as required to stiffen door and for wind loading. Ensure that reinforcement does not obstruct vision lites.

2. Provide reinforcement for hardware attachment.

B. Full-Vision Sections: Manufacturer's standard, tubular, aluminum-framed section fully glazed with 6-mm-thick, clear acrylic glazing set in vinyl, rubber, or neoprene glazing channel and with removable extruded-vinyl or aluminum stops.

2.2 TRACKS, SUPPORTS, AND ACCESSORIES

A. Tracks: Manufacturer's standard, galvanized-steel track system of configuration indicated, sized for door size and weight, designed for lift type indicated and clearances shown on Drawings. Provide complete track assembly including brackets, bracing, and reinforcement for rigid support of ball-bearing roller guides for required door type and size. Slot vertical sections of track spaced 2 inches



apart for door-drop safety device. Slope tracks at proper angle from vertical or design tracks to ensure tight closure at jambs when door unit is closed.

B. Track Reinforcement and Supports: Galvanized-steel track reinforcement and support members. Secure, reinforce, and support tracks as required for door size and weight to provide strength and rigidity without sag, sway, and vibration during opening and closing of doors.

C. Weatherseals: Replaceable, adjustable, continuous, compressible weather-stripping gaskets of flexible vinyl, rubber, or neoprene fitted to bottom and top of sectional door unless otherwise indicated.

D. Windows: Manufacturer's standard window units of type and size indicated and in arrangement shown. Provide removable stops of same material as door-section frames.

2.3 HARDWARE

A. General: Provide heavy-duty, corrosion-resistant hardware, with hot-dip galvanized, stainless-steel, or other corrosion-resistant fasteners, to suit door type.

B. Hinges: Heavy-duty, galvanized-steel hinges at each end stile and at each intermediate stile, according to manufacturer's written recommendations for door size. Attach hinges to door sections through stiles and rails.

C. Rollers: Heavy-duty rollers with steel ball-bearings in case-hardened steel races, mounted with varying projections to suit slope of track. Provide 3-inch- diameter roller tires for 3-inch- wide track and 2-inch- diameter roller tires for 2-inch- wide track.

D. Push/Pull Handles: For push-up or emergency-operated doors, provide galvanized-steel lifting handles on each side of door.

2.4 LOCKING DEVICES

A. Locking Device Assembly: Fabricate with cylinder lock, spring-loaded deadbolt, operating handle, cam plate, and adjustable locking bars to engage through slots in tracks.

1. Lock Cylinders: Provide cylinders and keyed to building keying system. 2. Keys: Three for each cylinder.

B. Chain Lock Keeper: Suitable for padlock.

C. Safety Interlock Switch: Equip power-operated doors with safety interlock switch to disengage power supply when door is locked.

2.5 COUNTERBALANCE MECHANISM

A. Torsion Spring: Counterbalance mechanism consisting of adjustable-tension torsion springs mounted on torsion shaft made of steel tube or solid steel. Provide springs designed for number of operation cycles indicated.

B. Cable Drums and Shaft for Doors: Cast-aluminum or gray-iron casting cable drums mounted on torsion shaft and grooved to receive door-lifting cables as door is raised. Mount counterbalance mechanism with manufacturer's standard ball-bearing brackets at each end of torsion shaft.

C. Cables: Galvanized-steel lifting cables.



D. Cable Safety Device: Include, on each side-edge of door, a device designed to automatically stop door if either lifting cable breaks.

E. Bracket: Provide anchor support bracket as required to connect stationary end of spring to the wall and to level the shaft and prevent sag.

F. Provide a spring bumper at each horizontal track to cushion door at end of opening operation.

2.6 MANUAL DOOR OPERATORS

A. Equip door with manufacturer's recommended manual door operator unless another type of door operator is indicated.

B. Push-up Operation: Lift handles and pull rope for raising and lowering doors, with counterbalance mechanism designed so that required lift or pull for door operation does not exceed 25 lbf.

C. Chain-Hoist Operator: Consisting of endless steel hand chain, chain-pocket wheel and guard, and gear-reduction unit with a maximum 25-lbf force for door operation. Provide alloy-steel hand chain with chain holder secured to operator guide.

2.7 ELECTRIC DOOR OPERATORS

A. General: Electric door operator assembly of size and capacity recommended and provided by door manufacturer for door and "operation cycles" requirement specified, with electric motor and factory-prewired motor controls, starter, gear-reduction unit, solenoid-operated brake, clutch, remote-control stations, control devices, integral gearing for locking door, and accessories required for proper operation.

1. Comply with NFPA 70. 2. Provide control equipment complying with NEMA ICS 1, NEMA ICS 2, and NEMA ICS 6; with

NFPA 70, Class 2 control circuit, maximum 24-V ac or dc.

B. Usage Classification: Electric operator and components capable of operating for not less than number of cycles per hour indicated for each door.

C. Door-Operator Type: Unit of type indicated, consisting of electric motor, gears, pulleys, belts, sprockets, chains, and controls needed to operate door and meet required usage classification.

D. Electric Motors: Comply with NEMA designation, temperature rating, service factor, enclosure type, and efficiency requirements specified in Division 11 Section "Common Motor Requirements for Equipment" unless otherwise indicated.


a. Phase: as indicated. b. Volts: as indicated. c. Hertz: 60.


3. Motor Size: Minimum size as indicated. If not indicated, large enough to start, accelerate, and operate door in either direction from any position, at a speed not less than 8 in./sec. and not more than 12 in./sec., without exceeding nameplate ratings or service factor.




E. Obstruction Detection Device: Equip motorized door with indicated external automatic safety sensor capable of protecting full width of door opening. Activation of device immediately stops and reverses downward door travel.

1. Photoelectric Sensor: Manufacturer's standard system designed to detect an obstruction in door opening without contact between door and obstruction. Provide self-monitoring capability designed to interface with door-operator control circuit to detect damage to or disconnection of sensor device.

F. Emergency Manual Operation: Equip each electrically powered door with capability for emergency manual operation. Design manual mechanism so required force for door operation does not exceed 25 lbf.

G. Emergency Operation Disconnect Device: Equip operator with hand-operated disconnect mechanism for automatically engaging manual operator and releasing brake for emergency manual operation while disconnecting motor without affecting timing of limit switch. Mount mechanism so it is accessible from floor level. Include interlock device to automatically prevent motor from operating when emergency operator is engaged.

H. Motor Removal: Design operator so motor may be removed without disturbing limit-switch adjustment and without affecting emergency manual operation.

I. Audible and Visual Signals: Audible alarm and visual indicator lights in compliance with regulatory requirements for accessibility.

2.8 DOOR ASSEMBLY

A. Full-Vision Aluminum Sectional Door: Sectional door formed with hinged sections.


a. Amarr Garage Doors. b. Arm-R-Lite. c. C.H.I. Overhead Doors. d. Clopay Building Products; a Griffon company. e. Fimbel Architectural Door Specialties. f. General American Door Company. g. Haas Door; a Nofziger company. h. Martin Door Manufacturing. i. Overhead Door Corporation. j. Raynor. k. Rite-Hite Corporation. l. Wayne-Dalton Corp. m. Windsor Republic Doors.


C. Installed R-Value: 17.5 deg F x h x sq. ft./Btu.

D. Aluminum Sections: Full vision.

E. Track Configuration: Contour track.



F. Weatherseals: Fitted to bottom and top and around entire perimeter of door.

G. Windows: Approximately 24 by 11 inches with square corners, and spaced apart the approximate distance as indicated on Drawings; at height indicated on Drawings; installed with insulated glazing of clear tempered glass.

H. Locking Devices: Equip door with locking device assembly chain lock keeper.

1. Locking Device Assembly: Single-jamb side locking bars, operable from inside and outside, with cylinders.

I. Manual Door Operator: Chain-hoist operator.

J. Electric Door Operator:

1. Usage Classification: Medium duty, up to 15 cycles per hour. 2. Operator Type: Jackshaft, side mounted. 3. Motor Exposure: Interior, clean, and dry, Exterior, dusty, wet, or humid. 4. Emergency Manual Operation: Chain type. 5. Obstruction-Detection Device: Automatic photoelectric sensor.

K. Door Finish:

1. Aluminum Finish: Clear anodized. 2. Finish of Interior Facing Material: Match finish of exterior section face.

PART 3 - EXECUTION

3.1 INSTALLATION

A. Install sectional doors and operating equipment complete with necessary hardware, anchors, inserts, hangers, and equipment supports; according to manufacturer's written instructions and as specified.

B. Tracks: Provide sway bracing, diagonal bracing, and reinforcement as required for rigid installation of track and door-operating equipment. Repair galvanized coating on tracks according to ASTM A 780.

C. Adjust hardware and moving parts to function smoothly so that doors operate easily, free of warp, twist, or distortion. Adjust doors and seals to provide weathertight fit around entire perimeter.

3.2 DEMONSTRATION

A. Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain sectional doors.



ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS 084113 1

SECTION 084113 - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS

PART 1 - GENERAL

1.1 SUMMARY


1. Exterior and interior storefront framing. 2. Storefront framing for window walls. 3. Storefront framing for ribbon walls. 4. Storefront framing for punched openings. 5. Exterior and interior manual-swing entrance doors and door frame units.


A. General Performance: Aluminum-framed systems shall withstand the effects of the following performance requirements without exceeding performance criteria or failure due to defective manufacture, fabrication, installation, or other defects in construction:

1. Movements of supporting structure indicated on Drawings including, but not limited to, story drift and deflection from uniformly distributed and concentrated live loads.

2. Dimensional tolerances of building frame and other adjacent construction. 3. Failure includes the following:

a. Deflection exceeding specified limits. b. Thermal stresses transferring to building structure. c. Framing members transferring stresses, including those caused by thermal and structural

movements to glazing. d. Noise or vibration created by wind and by thermal and structural movements. e. Loosening or weakening of fasteners, attachments, and other components. f. Failure of operating units.

B. Delegated Design: Design aluminum-framed systems, including comprehensive engineering analysis by a qualified professional engineer, using performance requirements and design criteria indicated.

C. Wind Loads: As indicated on Drawings

D. Deflection of Framing Members:

1. Deflection Normal to Wall Plane: Limited to edge of glass in a direction perpendicular to glass plane shall not exceed L/175 of the glass edge length for each individual glazing lite or an amount that restricts edge deflection of individual glazing lites to 3/4 inch (19 mm), whichever is less.

2. Deflection Parallel to Glazing Plane: Limited to L/360 of clear span or 1/8 inch (3.2 mm), whichever is smaller.

E. Structural-Test Performance: Provide aluminum-framed systems tested according to ASTM E 330 as follows:

1. When tested at 150 percent of positive and negative wind-load design pressures, systems, including anchorage, do not evidence material failures, structural distress, and permanent deformation of main framing members exceeding 0.2 percent of span.



2. Test Durations: 10 seconds.

F. Air Infiltration: Provide aluminum-framed systems with maximum air leakage through fixed glazing and framing areas of 0.06 cfm/sq. ft. (0.03 L/s per sq. m) of fixed wall area when tested according to ASTM E 283 at a minimum static-air-pressure difference of 1.57 lbf/sq. ft. (75 Pa).

G. Water Penetration under Static Pressure: Provide aluminum-framed systems that do not evidence water penetration through fixed glazing and framing areas when tested according to ASTM E 331 at a minimum static-air-pressure difference of 20 percent of positive wind-load design pressure, but not less than 6.24 lbf/sq. ft. (300 Pa).

1.3 SUBMITTALS


B. Shop Drawings: For aluminum-framed systems. Include plans, elevations, sections, details, and attachments to other work.

1. Include details of provisions for system expansion and contraction and for drainage of moisture in the system to the exterior.

C. Samples: For each type of exposed finish required.

D. Other Action Submittals:

1. Entrance Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of entrance door hardware, as well as procedures and diagrams.

E. Delegated-Design Submittal: For aluminum-framed systems indicated to comply with performance requirements and design criteria, including analysis data signed and sealed by the qualified professional engineer responsible for their preparation.

F. Product test reports.

G. Field quality-control reports.

H. Maintenance data.

I. Warranties: Sample of special warranties.


A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved for installation of units required for this Project.

B. Testing Agency Qualifications: Qualified according to ASTM E 699 for testing indicated.

C. Engineering Responsibility: Prepare data for aluminum-framed systems, including Shop Drawings, based on testing and engineering analysis of manufacturer's standard units in systems similar to those indicated for this Project.

D. Product Options: Information on Drawings and in Specifications establishes requirements for systems' aesthetic effects and performance characteristics. Aesthetic effects are indicated by dimensions, arrangements, alignment, and profiles of components and assemblies as they relate to sightlines, to one another, and to adjoining construction. Performance characteristics are indicated by criteria



subject to verification by one or more methods including preconstruction testing, field testing, and in-service performance.

E. Accessible Entrances: Comply with applicable provisions in ICC/ANSI A117.1.

F. Source Limitations for Aluminum-Framed Systems: Obtain from single source from single manufacturer.

G. Preinstallation Conference: Conduct conference at Project site.

1.5 WARRANTY

A. Special Warranty: Manufacturer's standard form in which manufacturer agrees to repair or replace components of aluminum-framed systems that do not comply with requirements or that fail in materials or workmanship within specified warranty period.


PART 2 - PRODUCTS

2.1 MANUFACTURERS


1. Arcadia, Inc. 2. Arch Aluminum & Glass Co., Inc. 3. CMI Architectural. 4. Commercial Architectural Products, Inc. 5. EFCO Corporation. 6. Kawneer North America; an Alcoa company. 7. Leed Himmel Industries, Inc. 8. Pittco Architectural Metals, Inc. 9. TRACO. 10. Tubelite. 11. United States Aluminum. 12. Vistawall Architectural Products; The Vistawall Group; a Bluescope Steel company. 13. YKK AP America Inc.

2.2 MATERIALS

A. Aluminum: Alloy and temper recommended by manufacturer for type of use and finish indicated.

1. Sheet and Plate: ASTM B 209 (ASTM B 209M). 2. Extruded Bars, Rods, Profiles, and Tubes: ASTM B 221 (ASTM B 221M). 3. Extruded Structural Pipe and Tubes: ASTM B 429. 4. Structural Profiles: ASTM B 308/B 308M. 5. Welding Rods and Bare Electrodes: AWS A5.10/A5.10M.

B. Steel Reinforcement: Manufacturer's standard zinc-rich, corrosion-resistant primer, complying with SSPC-PS Guide No. 12.00; applied immediately after surface preparation and pretreatment. Select surface preparation methods according to recommendations in SSPC-SP COM and prepare surfaces according to applicable SSPC standard.



1. Structural Shapes, Plates, and Bars: ASTM A 36/A 36M. 2. Cold-Rolled Sheet and Strip: ASTM A 1008/A 1008M. 3. Hot-Rolled Sheet and Strip: ASTM A 1011/A 1011M.

2.3 FRAMING SYSTEMS

A. Framing Members: Manufacturer's standard extruded-aluminum framing members of thickness required and reinforced as required to support imposed loads.

1. Construction: Nonthermal. 2. Glazing System: Retained mechanically with gaskets on four sides. 3. Glazing Plane: Center.

B. Brackets and Reinforcements: Manufacturer's standard high-strength aluminum with nonstaining, nonferrous shims for aligning system components.

C. Fasteners and Accessories: Manufacturer's standard corrosion-resistant, nonstaining, nonbleeding fasteners and accessories compatible with adjacent materials.

1. Use self-locking devices where fasteners are subject to loosening or turning out from thermal and structural movements, wind loads, or vibration.

2. Reinforce members as required to receive fastener threads. 3. Use exposed fasteners with countersunk Phillips screw heads, finished to match framing

system.

D. Concrete and Masonry Inserts: Hot-dip galvanized cast-iron, malleable-iron, or steel inserts, complying with ASTM A 123/A 123M or ASTM A 153/A 153M.

E. Concealed Flashing: Manufacturer's standard corrosion-resistant, nonstaining, nonbleeding flashing compatible with adjacent material.

F. Framing System Gaskets and Sealants: Manufacturer's standard, recommended by manufacturer for joint type.

1. Provide sealants for use inside of the weatherproofing system that have a VOC content of 250 g/L or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24).

2.4 GLAZING SYSTEMS

A. Glazing: As specified in Division 08 Section "Glazing."

B. Glazing Gaskets: Manufacturer's standard compression types; replaceable, molded or extruded, of profile and hardness required to maintain watertight seal.

C. Spacers and Setting Blocks: Manufacturer's standard elastomeric type.

2.5 ENTRANCE DOOR SYSTEMS

A. Entrance Doors: Manufacturer's standard glazed entrance doors for manual-swing operation.

1. Door Construction: 1-3/4-inch (44.5-mm) overall thickness, with minimum 0.125-inch- (3.2-mm-) thick, extruded-aluminum tubular rail and stile members. Mechanically fasten corners with reinforcing brackets that are deeply penetrated and fillet welded or that incorporate concealed tie rods.



2. Door Design: Wide stile; 5-inch (127-mm) nominal width.

a. Accessible Doors: Smooth surfaced for width of door in area within 10 inches (255 mm) above floor or ground plane.

3. Glazing Stops and Gaskets: Square, snap-on, extruded-aluminum stops and preformed gaskets.

a. Provide nonremovable glazing stops on outside of door.

B. Entrance Door Hardware: As specified in Division 08 Section "Door Hardware."

2.6 ENTRANCE DOOR HARDWARE

A. General: Provide entrance door hardware [and entrance door hardware sets indicated in door and frame schedule] for each entrance door to comply with requirements in this Section.

1. Entrance Door Hardware Sets: Provide quantity, item, size, finish or color indicated, and named manufacturers' products.

2. Sequence of Operation: Provide electrified door hardware function, sequence of operation, and interface with other building control systems indicated.

3. Opening-Force Requirements:

a. Egress Doors: Not more than 15 lbf (67 N) to release the latch and not more than 30 lbf (133 N) to set the door in motion and not more than 15 lbf (67 N) to open the door to its minimum required width.

b. Accessible Interior Doors: Not more than 5 lbf (22.2 N) to fully open door.

B. Opening-Force Requirements:

1. Delayed-Egress Locks: Lock releases within 15 seconds after applying a force of not more than 15 lbf (67 N) for not more than 3 seconds.

2. Latches and Exit Devices: Not more than 15 lbf (67 N) required to release latch.

C. Pivot Hinges: BHMA A156.4, Grade 1.

1. Offset-Pivot Hinges: Provide top, bottom, and intermediate offset pivots at each door leaf.

D. Butt Hinges: BHMA A156.1, Grade 1, radius corner.

1. Nonremovable Pins: Provide set screw in hinge barrel that, when tightened into a groove in hinge pin, prevents removal of pin while entrance door is closed.

2. Exterior Hinges: Nonferrous. 3. Quantities:

a. For doors up to 87 inches (2210 mm) high, provide 3 hinges per leaf. b. For doors more than 87 and up to 120 inches (2210 and up to 3048 mm) high, provide 4

hinges per leaf.

E. Continuous-Gear Hinges: Manufacturer's standard with stainless-steel bearings between knuckles, fabricated to full height of door and frame.

F. Mortise Auxiliary Locks: BHMA A156.5, Grade 1.

G. Manual Flush Bolts: BHMA A156.16, Grade 1.



H. Automatic and Self-Latching Flush Bolts: BHMA A156.3, Grade 1.

I. Panic Exit Devices: BHMA A156.3, Grade 1, listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for panic protection, based on testing according to UL 305.

J. Cylinders: As specified in Division 08 Section "Door Hardware."

1. Keying: Master key system. Permanently inscribe each key with a visual key control number and include notation to be furnished by Owner.

K. Strikes: Provide strike with black-plastic dust box for each latch or lock bolt; fabricated for aluminum framing.

L. Operating Trim: BHMA A156.6.

M. Removable Mullions: BHMA A156.3, extruded aluminum.

1. When used with panic exit devices, provide removable mullions listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for panic protection, based on testing according to UL 305. Use only mullions that have been tested with exit devices to be used.

N. Closers: BHMA A156.4, Grade 1, with accessories required for a complete installation, sized as required by door size, exposure to weather, and anticipated frequency of use; adjustable to meet field conditions and requirements for opening force.

O. Concealed Overhead Holders: BHMA A156.8, Grade 1.

P. Surface-Mounted Holders: BHMA A156.16, Grade 1.

Q. Door Stops: BHMA A156.16, Grade 1, floor or wall mounted, as appropriate for door location indicated, with integral rubber bumper.

R. Weather Stripping: Manufacturer's standard replaceable components.

S. Weather Sweeps: Manufacturer's standard exterior-door bottom sweep with concealed fasteners on mounting strip.

T. Silencers: BHMA A156.16, Grade 1.

U. Thresholds: BHMA A156.21, raised thresholds beveled with a slope of not more than 1:2, with maximum height of 1/2 inch (13 mm).

V. Finger Guards: Manufacturer's standard collapsible neoprene or PVC gasket anchored to frame hinge-jamb at center-pivoted doors.

2.7 ACCESSORY MATERIALS

A. Bituminous Paint: Cold-applied, asphalt-mastic paint complying with SSPC-Paint 12 requirements except containing no asbestos; formulated for 30-mil (0.762-mm) thickness per coat.

2.8 FABRICATION

A. Form or extrude aluminum shapes before finishing.



B. Weld in concealed locations to greatest extent possible to minimize distortion or discoloration of finish. Remove weld spatter and welding oxides from exposed surfaces by descaling or grinding.

C. Framing Members, General: Fabricate components that, when assembled, have the following characteristics:

1. Profiles that are sharp, straight, and free of defects or deformations. 2. Accurately fitted joints with ends coped or mitered. 3. Means to drain water passing joints, condensation within framing members, and moisture

migrating within the system to exterior. 4. Physical and thermal isolation of glazing from framing members. 5. Accommodations for thermal and mechanical movements of glazing and framing to maintain

required glazing edge clearances. 6. Provisions for field replacement of glazing from interior for vision glass and exterior for spandrel

glazing or metal panels. 7. Fasteners, anchors, and connection devices that are concealed from view to greatest extent

possible.

D. Mechanically Glazed Framing Members: Fabricate for flush glazing without projecting stops.

E. Entrance Door Frames: Reinforce as required to support loads imposed by door operation and for installing entrance door hardware.

F. Entrance Doors: Reinforce doors as required for installing entrance door hardware.

G. Entrance Door Hardware Installation: Factory install entrance door hardware to the greatest extent possible. Cut, drill, and tap for factory-installed entrance door hardware before applying finishes.

H. After fabrication, clearly mark components to identify their locations in Project according to Shop Drawings.

2.9 ALUMINUM FINISHES

A. Clear Anodic Finish: AAMA 611, AA-M12C22A41, Class I, 0.018 mm.

PART 3 - EXECUTION

3.1 INSTALLATION

A. General:

1. Comply with manufacturer's written instructions. 2. Do not install damaged components. 3. Fit joints to produce hairline joints free of burrs and distortion. 4. Rigidly secure nonmovement joints. 5. Install anchors with separators and isolators to prevent metal corrosion and electrolytic

deterioration. 6. Seal joints watertight unless otherwise indicated.

B. Metal Protection:

1. Where aluminum will contact dissimilar metals, protect against galvanic action by painting contact surfaces with primer or applying sealant or tape, or by installing nonconductive spacers as recommended by manufacturer for this purpose.



2. Where aluminum will contact concrete or masonry, protect against corrosion by painting contact surfaces with bituminous paint.

C. Install components to drain water passing joints, condensation occurring within framing members, and moisture migrating within the system to exterior.

D. Set continuous sill members and flashing in full sealant bed as specified in Division 07 Section "Joint Sealants" to produce weathertight installation.

E. Install components plumb and true in alignment with established lines and grades, and without warp or rack.

F. Install glazing as specified in Division 08 Section "Glazing."

G. Entrance Doors: Install doors to produce smooth operation and tight fit at contact points.

1. Exterior Doors: Install to produce weathertight enclosure and tight fit at weather stripping. 2. Field-Installed Entrance Door Hardware: Install surface-mounted entrance door hardware

according to entrance door hardware manufacturers' written instructions using concealed fasteners to greatest extent possible.

3.2 FIELD QUALITY CONTROL

A. Repair or remove work if test results and inspections indicate that it does not comply with specified requirements.

B. Additional testing and inspecting, at Contractor's expense, will be performed to determine compliance of replaced or additional work with specified requirements.

C. Aluminum-framed assemblies will be considered defective if they do not pass tests and inspections.

D. Prepare test and inspection reports.



GLAZED ALUMINUM CURTAIN WALLS 084413 1

SECTION 084413 - GLAZED ALUMINUM CURTAIN WALLS

PART 1 - GENERAL

1.1 SUMMARY

A. Section includes conventionally glazed aluminum curtain walls installed as stick assemblies.


A. General Performance: Comply with performance requirements specified, as determined by testing of manufacturer's standard glazed aluminum curtain walls representing those indicated for this Project without failure due to defective manufacture, fabrication, installation, or other defects in construction.

1. Glazed aluminum curtain walls shall withstand movements of supporting structure including, but not limited to, story drift, twist, column shortening, long-term creep, and deflection from uniformly distributed and concentrated live loads.

2. Failure also includes the following:

a. Thermal stresses transferring to building structure. b. Glass breakage. c. Noise or vibration created by wind and thermal and structural movements. d. Loosening or weakening of fasteners, attachments, and other components. e. Failure of operating units.

B. Delegated Design: Design glazed aluminum curtain walls, including comprehensive engineering analysis by a qualified professional engineer, using performance requirements and design criteria indicated.

C. Wind Loads: 150 MPH.

D. Structural-Test Performance: Test according to ASTM E 330 as follows:

1. When tested at 150 percent of positive and negative wind-load design pressures, assemblies, including anchorage, do not evidence material failures, structural distress, and permanent deformation of main framing members exceeding 0.2 percent of span.

2. Test Durations: 10 seconds.

E. Deflection of Framing Members: At design wind pressure, as follows:

1. Deflection Normal to Wall Plane: Limited to edge of glass in a direction perpendicular to glass plane not exceeding L/175 of the glass edge length for each individual glazing lite or an amount that restricts edge deflection of individual glazing lites to 3/4 inch, whichever is less.

2. Deflection Parallel to Glazing Plane: Limited to L/360 of clear span or 1/8 inch, whichever is smaller.

3. Cantilever Deflection: Where framing members overhang an anchor point, limit deflection to two times the length of cantilevered member, divided by 175.

F. Water Penetration under Static Pressure: No evidence of water penetration through fixed glazing and framing areas when tested according to ASTM E 331 at a minimum static-air-pressure differential of 20 percent of positive wind-load design pressure, but not less than 6.24 lbf/sq. ft..

G. Energy Performance: Glazed aluminum curtain wall shall have certified and labeled energy performance ratings in accordance with NFRC.



1.3 SUBMITTALS


B. Shop Drawings: For glazed aluminum curtain walls. Include plans, elevations, sections, full-size details, and attachments to other work.

1. Include details of provisions for assembly expansion and contraction and for draining moisture occurring within the assembly to the exterior.

2. Include full-size isometric details of each vertical-to-horizontal intersection of glazed aluminum curtain walls, showing the following:

a. Joinery, including concealed welds. b. Anchorage. c. Expansion provisions. d. Glazing. e. Flashing and drainage.

C. Samples: For each type of exposed finish required.

D. Delegated-Design Submittal: For glazed aluminum curtain walls indicated to comply with performance requirements and design criteria, including analysis data signed and sealed by the qualified professional engineer responsible for their preparation.

1. Qualification Data: For qualified Installer.

E. Product test reports.

F. Field quality-control reports.

G. Maintenance data.

H. Warranties: Sample of special warranties.


A. Installer Qualifications: Manufacturer's authorized representative who is trained and approved for installation of units required for this Project.

B. Testing Agency Qualifications: Qualified according to ASTM E 699 for testing indicated.

C. Product Options: Information on Drawings and in Specifications establishes requirements for aesthetic effects and performance characteristics of assemblies. Aesthetic effects are indicated by dimensions, arrangements, alignment, and profiles of components and assemblies as they relate to sightlines, to one another, and to adjoining construction.

D. Energy Performance Standards: Comply with NFRC for minimum standards of energy performance, materials, components, accessories, and fabrication. Comply with more stringent requirements if indicated.

1. Provide NFRC-certified glazed aluminum curtain walls with an attached label.

E. Preinstallation Conference: Conduct conference at Project site.



1.5 WARRANTY

A. Special Assembly Warranty: Standard form in which manufacturer agrees to repair or replace components of glazed aluminum curtain walls that do not comply with requirements or that fail in materials or workmanship within specified warranty period.


B. Special Finish Warranty: Standard form in which manufacturer agrees to repair finishes or replace aluminum that shows evidence of deterioration of factory-applied finishes within specified warranty period.


PART 2 - PRODUCTS

2.1 MANUFACTURERS


1. Arcadia, Inc. 2. Arch Aluminum & Glass Co., Inc. 3. Bruce Wall Systems Corporation. 4. CMI Architectural. 5. EFCO Corporation. 6. Glassalum International Corporation. 7. Kawneer North America; an Alcoa company. 8. Pittco Architectural Metals, Inc. 9. Tingwall Inc. 10. TRACO. 11. Tubelite. 12. United States Aluminum. 13. Vistawall Architectural Products; The Vistawall Group; a Bluescope Steel company. 14. Waltek & Company Limited. 15. Wausau Window and Wall Systems. 16. YKK AP America Inc.

2.2 MATERIALS

A. Aluminum: Alloy and temper recommended by manufacturer for type of use and finish indicated.

1. Sheet and Plate: ASTM B 209. 2. Extruded Bars, Rods, Profiles, and Tubes: ASTM B 221. 3. Extruded Structural Pipe and Tubes: ASTM B 429. 4. Structural Profiles: ASTM B 308/B 308M. 5. Welding Rods and Bare Electrodes: AWS A5.10/A5.10M.

B. Steel Reinforcement: With manufacturer's standard zinc-rich, corrosion-resistant primer complying with SSPC-PS Guide No. 12.00; applied immediately after surface preparation and pretreatment. Select surface preparation methods according to recommendations in SSPC-SP COM and prepare surfaces according to applicable SSPC standard.

1. Structural Shapes, Plates, and Bars: ASTM A 36/A 36M. 2. Cold-Rolled Sheet and Strip: ASTM A 1008/A 1008M.



3. Hot-Rolled Sheet and Strip: ASTM A 1011/A 1011M.

2.3 FRAMING

A. Framing Members: Manufacturer's standard extruded- or formed-aluminum framing members of thickness required and reinforced as required to support imposed loads.

1. Construction: Nonthermal. 2. Glazing System: As indicated. 3. Glazing Plane: Front.

B. Brackets and Reinforcements: Manufacturer's standard high-strength aluminum with nonstaining, nonferrous shims for aligning system components.

C. Fasteners and Accessories: Manufacturer's standard corrosion-resistant, nonstaining, nonbleeding fasteners and accessories compatible with adjacent materials.

1. Use self-locking devices where fasteners are subject to loosening or turning out from thermal and structural movements, wind loads, or vibration.

2. Reinforce members as required to receive fastener threads. 3. Use exposed fasteners with countersunk Phillips screw heads, finished to match framing

system.

D. Anchors: Three-way adjustable anchors with minimum adjustment of 1 inch that accommodate fabrication and installation tolerances in material and finish compatible with adjoining materials and recommended by manufacturer.

1. Concrete and Masonry Inserts: Hot-dip galvanized cast-iron, malleable-iron, or steel inserts complying with ASTM A 123/A 123M or ASTM A 153/A 153M requirements.

E. Concealed Flashing: Manufacturer's standard corrosion-resistant, nonstaining, nonbleeding flashing compatible with adjacent materials.

F. Framing Sealants: Manufacturer's standard sealants.

2.4 GLAZING

A. Glazing: Comply with Division 08 Section "Glazing."

B. Glazing Gaskets: Manufacturer's standard sealed-corner pressure-glazing system of black, resilient elastomeric glazing gaskets, setting blocks, and shims or spacers.

C. Glazing Sealants: As recommended by manufacturer.

1. Provide sealants for use inside of the weatherproofing system that have a VOC content of 250 g/L or less when calculated according to 40 CFR 59, Subpart D (EPA Method 24).

2.5 ACCESSORY MATERIALS

A. Bituminous Paint: Cold-applied asphalt-mastic paint complying with SSPC-Paint 12 requirements except containing no asbestos, formulated for 30-mil thickness per coat.



2.6 FABRICATION

A. Form or extrude aluminum shapes before finishing.

B. Weld in concealed locations to greatest extent possible to minimize distortion or discoloration of finish. Remove weld spatter and welding oxides from exposed surfaces by descaling or grinding.

C. Fabricate components that, when assembled, have the following characteristics:

1. Profiles that are sharp, straight, and free of defects or deformations. 2. Accurately fitted joints with ends coped or mitered. 3. Physical and thermal isolation of glazing from framing members. 4. Accommodations for thermal and mechanical movements of glazing and framing to maintain

required glazing edge clearances. 5. Provisions for field replacement of glazing from exterior. 6. Fasteners, anchors, and connection devices that are concealed from view to greatest extent

possible.

D. Fabricate components that, when assembled, have the following characteristics:

1. Internal guttering system or other means to drain water passing joints, condensation occurring within framing members, and moisture migrating within glazed aluminum curtain wall to exterior.

2. Pressure-equalized system or double barrier design with primary air and vapor barrier at interior side of glazed aluminum curtain wall and secondary seal weeped and vented to exterior.

E. Factory-Assembled Frame Units:

1. Rigidly secure nonmovement joints. 2. Seal joints watertight unless otherwise indicated. 3. Install glazing to comply with requirements in Division 08 Section "Glazing."

F. After fabrication, clearly mark components to identify their locations in Project according to Shop Drawings.

2.7 ALUMINUM FINISHES

A. Clear Anodic Finish: AA-M12C22A41, Class I, 0.018 mm or thicker.

PART 3 - EXECUTION

3.1 INSTALLATION

A. General:

1. Comply with manufacturer's written instructions. 2. Do not install damaged components. 3. Fit joints to produce hairline joints free of burrs and distortion. 4. Rigidly secure nonmovement joints. 5. Install anchors with separators and isolators to prevent metal corrosion and electrolytic

deterioration and to prevent impeding movement of moving joints. 6. Weld components in concealed locations to minimize distortion or discoloration of finish.

Protect glazing surfaces from welding. 7. Seal joints watertight unless otherwise indicated.



B. Metal Protection:

1. Where aluminum will contact dissimilar metals, protect against galvanic action by painting contact surfaces with primer or by applying sealant or tape or installing nonconductive spacers as recommended by manufacturer for this purpose.

2. Where aluminum will contact concrete or masonry, protect against corrosion by painting contact surfaces with bituminous paint.

C. Install components to drain water passing joints, condensation occurring within framing members, and moisture migrating within glazed aluminum curtain wall to exterior.

D. Install components plumb and true in alignment with established lines and grades.

E. Install glazing as specified in Division 08 Section "Glazing."

3.2 ERECTION TOLERANCES

A. Erection Tolerances: Install glazed aluminum curtain walls to comply with the following maximum tolerances:

1. Plumb: 1/8 inch in 10 feet; 1/4 inch in 40 feet. 2. Level: 1/8 inch in 20 feet; 1/4 inch in 40 feet. 3. Alignment:

a. Where surfaces abut in line or are separated by reveal or protruding element up to 1/2 inch wide, limit offset from true alignment to 1/16 inch.

b. Where surfaces are separated by reveal or protruding element from 1/2 to 1 inch wide, limit offset from true alignment to 1/8 inch.

c. Where surfaces are separated by reveal or protruding element of 1 inch wide or more, limit offset from true alignment to 1/4 inch.

4. Location: Limit variation from plane to 1/8 inch in 12 feet; 1/2 inch over total length.



FINISH HARDWARE 087100 1

SECTION 087100 – FINISH HARDWARE

PART 1 - GENERAL

1.01 SUMMARY

A. Section Includes 1. Finish hardware for doors as scheduled and specified herein, including:

a. Mechanical hardware swinging doors. 2. Electro-mechanical devices and access control components as specified herein. 3. Any parts, components, materials, and accessories, whether specified or not, that are

required for a complete and operational access control system. Provide access control system with features, capabilities, and operation at each door as specified herein.

B. Related Sections 1. Provide hardware complying with division 01 section “references” as well as the following

publications to the extent referenced within this specification. a. Division 08 Section: “Hollow Metal Doors and Frames” b. Division 08 Section: “Wood Doors” c. Division 08 Section: “Aluminum-Framed Entrances and Storefronts” d. Division 08 Section: “Overhead Coiling Doors”

1.02 REFERENCED STANDARDS

A. Provide hardware in accordance with the following standards in addition to those specified in Division 01 Section “References.” 1. American National Standards Institute (ANSI), A117.1: Accessible and Usable Buildings and

Facilities, edition as adopted by local Authority Having Jurisdiction (AHJ). 2. Builders Hardware Manufacturer’s Association (BHMA)

a. ANSI/BHMA A156.18: Materials and Finishes, 2006 edition 3. Door and Hardware Institute (DHI)

a. Recommended Locations for Architectural Hardware for Flush Wood Doors, 1993 edition

b. Recommended Locations for Architectural Hardware for Standard Steel Doors and Frames, 2004 edition

c. Installation Guide for Doors and Hardware, 1994 edition d. Keying Systems and Nomenclature, 2003 edition e. Sequence and Format for the Hardware Schedule, 2001 edition

4. National Fire Protection Association (NFPA) a. NFPA 80: Standard for Fire Doors and Other Opening Protectives, edition as adopted

by local AHJ. b. NFPA 105: Standard for the Installation of Smoke Door Assemblies and Other

Opening Protectives, edition as adopted by local AHJ. c. NFPA 252: Standard Methods of Fire Tests of Door Assemblies, edition as adopted

by local AHJ.

1.03 ADMINISTRATIVE REQUIREMENTS

A. Coordination 1. Coordinate layout, templating, and installation of work with other sections as required.

Provide templates, product information, schedules, and diagrams required to fully coordinate the work. a. Coordinate floor-recessed hardware with Division 03 Section “Cast-in-Place

Concrete.” b. Coordinate blocking for wall stops and other surface-applied hardware with Division

06 Section “Rough Carpentry.”



c. Coordinate hardware locations and templating with the appropriate Division 08 door and frame sections.

d. Fire Rated Openings: Coordinate with door and frame manufacturer to ensure that total opening complies with requirements for fire doors.

B. Pre-installation Meetings 1. Upon approval of hardware schedule and wiring diagram submittals and before hardware

installation, conduct a pre-installation meeting complying with Division 01 Section “Project Management and Coordination.”

2. Meeting attendees shall include the owner’s representative, architect, contractor, hardware supplier, hardware installer, other affected trades, and manufacturer representative(s) for locks, exit hardware, operators, and closers.

3. Discuss the installation of continuous hinges, locksets, door closers, exit devices, electromechanical finish hardware, and finish hardware. Coordinate installation between trades. a. Discuss special installation requirements. b. Inspect and discuss electrical rough-in and other preparatory work performed by other

trades. c. Review sequence of operation for each electrified door opening. d. Review and finalize construction schedule and verify availability of materials,

Installer's personnel, equipment, and facilities needed to make progress and avoid delays.

e. Review required testing, inspecting, and certifying procedures 4. At the meeting, distribute installation manuals, templates, wiring diagrams, and approved

hardware schedule submittals to each attendee. 5. Notify participants at least five (5) working days before meeting.

C. Keying Conference 1. Upon approval of hardware schedule and before ordering locking hardware and key system,

conduct a keying meeting complying with Division 01 Section “Project Management and Coordination.”

2. Meeting attendees shall include the owner, owner’s security consultant, construction manager, contractor, architect, and hardware supplier’s Architectural Hardware Consultant.

3. Discuss key system requirements and incorporate decisions made during the meeting into the keying schedule submittal. a. Review each locking function and determine degree of security required at each

opening. b. Review function of building, flow of traffic, and purpose of each area. c. Determine degree of security at each opening. d. Determine requirements for future expansion. e. Discuss requirements for shipping and delivery of keys and cylinders/cores. f. Discuss requirements to interface new cylinders/cores with owner’s existing key

system.

1.04 SUBMITTALS

A. General 1. Provide submittals in accordance with Division 01 Section “Submittal Procedures.” 2. Advise architect within the submittal package of incompatibility or issues which may

detrimentally affect the work of this section. 3. Submittals shall be prepared by or under the supervision of Architectural Hardware

Consultant. Stamp submittals with the DHI certification seal and signature of the supervising Architectural Hardware Consultant. a. Submittals submitted without the above certification seal shall be marked incomplete

and returned. 4. Submittal sequence: Submit product data, hardware schedule, samples, and qualification

data concurrently. Coordinate submission of finish hardware schedule with scheduling



requirements of other work to facilitate the fabrication of other work that is critical in project construction schedule. Upon approval of first submittal package, submit wiring diagrams and key schedule.

B. Product Data 1. Submit manufacturer’s technical product data for each item of finish hardware, installation

instructions, maintenance of operating parts and finish, and other information necessary to show compliance with requirements.

2. Highlight relevant product information such as model, function, trim, finish, options, electrical requirements, and accessories.

C. Hardware Schedule 1. Submit hardware schedule detailing fabrication and assembly of finish hardware, as well as

procedures and diagrams. Coordinate the final finish hardware sets with doors, frames, and related work to ensure proper size, thickness, hand, function, and finish of finish hardware.

2. Check specified hardware for suitability and adaptability to details and surrounding conditions. Indicate unsuitable or incompatible items and proposed substitutions. a. Format schedule complying with the vertical format in DHI's "Sequence and Format

for the Hardware Schedule" publication. Double space entries, and number and date each page. Use same scheduling sequence and door numbers as in the Contract Documents

b. Include the following information: 1) Numerical door index indicating door number, heading number, and architect’s

specified hardware set number. 2) Identification number, location, hand, fire rating and material of each door and

frame. 3) Type, style, function, size, quantity, and finish of each finish hardware item.

Include description and function of each lockset and exit device. 4) Complete designations of every item required for each door or opening

including name and manufacturer. 5) Fastenings and other pertinent information. 6) Location of each finish hardware set, cross-referenced to Drawings, both on

floor plans and in door and frame schedule. 7) Explanation of abbreviations, symbols, and codes contained in schedule. 8) Mounting locations for finish hardware. 9) Door and frame sizes and materials. 10) Description of each electrified finish hardware function, including location,

sequence of operation, and interface with other building control systems. a) Sequence of Operation: Include description of component functions that

occur in the following situations: authorized person wants to enter; authorized person wants to exit; unauthorized person wants to enter; unauthorized person wants to exit; loss of power; fire alarm sounds.

11) List of related door devices specified in other Sections for each door and frame. c. Submit, with the hardware schedule, a list of lead times for hardware items.

D. Keying Schedule 1. Submit keying schedule detailing Owner's final keying instructions for locks. Include

schematic keying diagram and index each key set to unique door designations complying with DHI’s “Keying Systems and Nomenclature” publication.

E. Manufacturer’s Templates 1. After final approval of the hardware schedule, provide templates for doors, frames, and other

work specified to be factory prepared for the installation of finish hardware. Check shop drawings of other work to ensure that adequate provisions are made for locating and installing finish hardware to comply with indicated requirements. Provide additional templates, template lists, hardware schedules, and product information to other trades upon request.



1.05 CLOSE OUT SUBMITTALS

A. General 1. Upon substantial completion, provide two (2) copies of the closeout submittals complying

with Division 01 Section “Close Out Submittals.”

B. Operation And Maintenance Data 1. Provide operation and maintenance manuals that include the following for each hardware

item: a. Project information including contact information for architect, contractor, supplier,

installer, Architectural Hardware Consultant, and local representative of each hardware manufacturer

b. Complete information on care, maintenance, adjustment, repair and replacement of parts, and preservation of finishes

c. Product data, templates, installation information, service manual, and parts lists. d. Copy of final hardware and keying schedules and wiring diagrams for each opening

connected to either 120V or low voltage power. Edit schedules and diagrams to reflect “As installed” conditions.

C. Warranty Documentation 1. Provide information required for warranty service or replacement of each hardware item

including: a. Warranty certificates from manufacturer stating warranty period and conditions,

complying with warranty requirements specified herein. b. Copy of manufacturer’s order confirmation or original packing slip with manufacturer’s

original order #, date of manufacture, and ship date.


A. Qualifications 1. Supplier Qualifications: Supplier shall have documented experience in the supply of finish

hardware for five (5) years or for three (3) prior projects similar in scope, size, and quality. Supplier shall have an Architectural Hardware Consultant, complying with the requirements specified herein, available to properly handle, detail, and service hardware in a satisfactory manner. Architectural Hardware Consultant shall be available during the course of the work to consult with contractor, architect, and owner about finish hardware and keying. a. Supplier shall be a certified direct distributor and be a full sales and service

organization for the manufacturer(s) listed. 2. Installer Qualifications: Installer shall have documented experience in the installation of finish

hardware for (5) years or for three (3) prior projects similar in scope, size, and quality. 3. Manufacturer Sourcing Qualifications: Obtain each type of finish hardware (hinges, latch &

locksets, exit devices, closers, etc.) from a single manufacturer, although several may be indicated as offering products complying with requirements. a. Provide electrified hardware from same manufacturer as mechanical finish hardware

unless otherwise indicated. Manufacturer’s that perform electrical modifications that are listed by a testing and inspecting agency acceptable to authorities having jurisdiction (AHJ) are acceptable.

4. Architectural Hardware Consultant Qualifications: A person who is certified by DHI as an Architectural Hardware Consultant (AHC) or Architectural Openings Consultant (AOC) and is enrolled in the DHI Continuing Education Program. Consultant shall be experienced in providing consulting services for finish hardware installations that are comparable in material, design, and extent indicated.

B. Fire Door Assemblies 1. Provide finish hardware for fire rated openings that complies with NFPA 80 and the

requirements of the AHJ. Provide only items of finish hardware that are listed by a testing and inspecting agency acceptable to the AHJ for use on types and sizes of doors indicated,



based on testing at positive pressure and according to NFPA 252 or UL 10C and in compliance with fire-rated door and frame labels. a. Where exit devices are required on fire rated doors (with supplementary marking on

door label indicating “Fire Door to be Equipped with “Fire Exit Hardware”), provide label on exit device indicating “Fire Exit Hardware.”

b. Provide proper latching hardware, non-flaming door closers, approved bearing type hinges, and required gasketing if not furnished with door or frame.

C. Smoke And Draft Control Door Assemblies 1. Where smoke and draft control door assemblies are required, provide finish hardware that

meets requirements of assemblies tested according to UL 1784 and installed in compliance with NFPA 105.

1.07 DELIVERY, STORAGE, AND HANDLING

A. Marking And Packaging 1. Package hardware items manufacturer’s standard packaging, clearly marked with hardware

set number correlating to finish hardware schedule and architect’s door number.

B. Delivery And Acceptance 1. Coordinate with construction schedule and deliver packaged hardware items to place of

installation (e.g. project site, fabrication shop). Upon delivery, inspect and inventory finish hardware. Immediately notify supplier of defective or missing items.

2. Deliver keys and cores to owner by registered mail or overnight package service. Ship keys separately from cores.

C. Storage And Handling 1. Provide secure, dry storage area complying with Division 01 Section “Product Storage and

Handling Requirements” for finish hardware delivered to the project site, but not yet installed. Store items on shelves or pallets to prevent damage.

2. Control handling and installation of hardware items that are not immediately replaceable so that completion of work will not be delayed by hardware losses both before and after installation.

1.08 WARRANTY

A. General Warranty 1. Warrant finish hardware against defects in material and workmanship as set forth in Division

01 Section “Warranties.” 2. Special warranties specified herein shall not deprive owner of other rights specified in the

contract documents, but shall be in addition to, and run concurrent with, other warranty requirements.

B. Special Warranty 1. Provide a written warranty, executed by the product manufacturer agreeing to repair or

replace components of finish hardware that fail in materials or workmanship within the specified warranty period. a. Failures include, but are not limited to, the following:

1) Structural failures including excessive deflection, cracking, or breakage. 2) Faulty operation of finish hardware. 3) Deterioration of metals, metal finishes, and other materials beyond normal

wear. b. Warranty Period: Two (2) years from date of Substantial Completion, except for:

1) Heavy Duty Bored Locks: Ten (10) years from date of substantial completion 2) Exit Devices: Three (3) years from date of substantial completion 3) Door Closers: Twenty five (25) years from date of substantial completion 4) Electrified Hardware Items: One (1) years from date of substantial completion



PART 2 - PRODUCTS

2.01 MANUFACTURERS

A. Substitutions submitted, no later than 10 business days prior to bid and complying with Division 01 Section “Substitutions” requirements will be reviewed for conformance to basis of design. Substitutions found in compliance will be approved by bid addendum.

2.02 MATERIALS

A. Manufacturer's Name Plate: Do not use manufacturers' products that have manufacturer's name or trade name displayed in a visible location (omit removable nameplates) except in conjunction with required fire-rated labels and as otherwise acceptable to Architect. 1. Manufacturer's identification will be permitted on rim of lock cylinders only.

B. Base Metals: Produce hardware units of basic metal and forming method indicated using manufacturer's standard metal alloy, composition, temper, and hardness, but in no case of lesser (commercially recognized) quality than specified for applicable hardware units for finish designations indicated.

C. Provide hardware manufactured to conform to published templates generally prepared for machine screw installation. Do not provide hardware that has been prepared for self-tapping sheet metal screws, except as specifically indicated.

2.03 FASTENERS

A. Furnish screws for installation with each hardware item. Provide Phillips flat-head screws except as otherwise indicated. Furnish stainless steel (exposed under any condition) screws to match hardware finish or, if exposed in surfaces of other work, to match finish of this other work as closely as possible including "prepared for paint" surfaces to receive painted finish.

B. Provide concealed fasteners for hardware units that are exposed when door is closed except to the extent no standard units of type specified are available with concealed fasteners. Use through bolts only as indicated in this section unless their use is the only means of reinforcing the work adequately to fasten the hardware securely. Where thru-bolts are used as a means of reinforcing the work, provide sleeves for each thru-bolt or use sex screw fasteners.

2.04 HINGES

A. Products that may be incorporated into the Work: 1. Ives: 5BB1 5BB1HW 2. Stanley: FBB179 FBB168 3. McKinney: TB2714 T4B3386

B. Requirements: 1. Screws: Provide Phillips flat-head screws complying with the following requirements:

a. For metal doors and frames install machine screws into drilled and tapped holes. b. For wood doors and frames install wood screws. c. For fire-rated wood doors install #12 x 1-1/4-inch, threaded-to-the-head steel wood

screws. 2. Hinge Pins: Except as otherwise indicated, provide hinge pins as follows:

a. Out-Swing Doors with Locks: Non-Removable Pins (NRP). b. Interior Doors: Non-rising pins. c. Tips: Flat button and matching plug, finished to match leaves.

3. Number of Hinges: At non-rated openings, provide two hinges for each door leaf 60 inches or less in height and one additional hinge for each 30 inches of additional height or portion thereof. At fire rated openings, provide no less than three ball bearing hinges for each door leaf 86 inches or less in height and one additional hinge for each 30 inches of additional height or portion thereof.



4. Hinge Width: Where applied trim or closer templating require hinge widths wider than 4-1/2 inches, provide minimum width required. Otherwise, provide hinges 4-1/2 inches in width.

5. Hinge Height: Provide hinges 5 inches in height where door leaf exceeds 3’0 in width or where door is a high-use door utilizing panic or push/pull hardware. Otherwise, provide hinges 4-1/2 inches in height.

6. Hinge Weight: Provide heavy weight hinges where door leaf exceeds 3’0 in width, exterior doors, and at doors scheduled with swing clear hinges, panic hardware, push/pull hardware, edge guards, or armor plates. Otherwise provide standard weight hinges.

2.05 CONTINUOUS HINGES

A. Products that may be incorporated into the Work: 1. Ives: 112HD 2. Stanley: 661HD 3. Select: SL11HD

B. Requirements: 1. Geared Continuous Hinges: Shall utilize a single gear section for the door leaf and a

separate gear section for the frame side of the door. Provide full mortise or surface applied hinge as scheduled in each set. Geared hinges are to be UL 10C tested and approved for 90 minutes.

2.06 OPERATING DOOR TRIM

A. Door Bolts 1. Products that may be incorporated into the Work:

a. Ives: FB358/FB458 b. Rockwood: 557/555 c. Trimco: 3915/3917

2. Requirements: a. Provide bolt model recommended by manufacturer for door material type. b. Provide 1 inch throw stainless steel bolt with 12 inch length unless otherwise

scheduled in the sets.

B. Push Plates, Pull Plates, and Pulls 1. Products that may be incorporated into the Work:

a. Ives: 8200 8303 9190 b. Rockwood: 70C 111x70C BF15747 c. Trimco: 1001 1018 1730

2. Requirements: a. Push Plate: Provide 6 inch by 16 inch by .050 inch push plate constructed of brass,

bronze, or stainless steel. Bevel all four edges. b. Pull Plate: Provide 4 (or 6) inch by 16 inch by .050 inch push plate constructed of

brass, bronze, or stainless steel, bevel all four edges. Provide 10 inch center to center (CTC) pull constructed of brass, bronze, or stainless steel with a diameter of 1 inch.

c. Push/Pull Bar: Provide 10 inch center to center (CTC) pull with a 4 inch offset and door pull equal to door width less 3 inches. Push/pull bar shall be constructed of stainless steel with a diameter of 1 inch.

2.07 DECORATIVE DOOR PULLS

A. Products that may be incorporated into the Work: 1. Ives: 9264 9266

B. Requirements: 1. Provide door pulls 1-1/4 inch diameter with flat tips. Pull shall be constructed of brass,

bronze, or stainless steel. 2. Provide pull length and shape as indicated in the sets.



3. Door pulls must not extend within bottom ten inches of the door on push side.

2.08 LOCKS AND LATCHES

A. Mortise Locks 1. Products that may be incorporated into the Work:

a. Schlage: L Series, 06A Lever 2. Requirements:

a. Provide mortise locks conforming to ANSI/BHMA A156.13 Series 1000, Grade 1 Operational, Grade 1 Security, and manufactured from heavy gauge steel, containing components of steel with a zinc dichromate plating for corrosion resistance. Provide lock case that is multi-function and field reversible for handing without opening case.

b. Provide locks with standard 2-3/4 inches (70 mm) backset with full 3/4 inch (19 mm) throw stainless steel mechanical anti-friction latchbolt. Provide deadbolt with full 1 inch (25 mm) throw, constructed of stainless steel.

c. Provide standard ASA strikes unless extended lip strikes are necessary to protect trim.

d. Lever Trim: Solid brass, bronze, or stainless steel, cast or forged in design specified, with wrought roses and external lever spring cages. Provide thru-bolted levers with 2-piece spindles.

e. Provide Occupied/Vacant indicators as scheduled.

B. Heavy Duty Bored Locks 1. Products that may be incorporated into the Work:

a. Schlage: ND Series, Rhodes Lever 2. Requirements:

a. Provide cylindrical locks conforming to ANSI/BHMA A156.2 Series 4000, Grade 1. b. Provide locks with standard 2-3/4 inches (70 mm) backset, unless noted otherwise,

with 1/2 inch latch throw. Provide proper latch throw for UL listing at pairs. c. Provide locksets with separate anti-rotation thru-bolts, and no exposed screws. d. Provide independently operating levers with two external return spring cassettes

mounted under roses to prevent lever sag. e. Provide standard ASA strikes unless extended lip strikes are necessary to protect

trim. f. Lever Trim: Solid cast levers without plastic inserts, and wrought roses on both sides.

C. Narrow Style Aluminum Door Lock 1. Product that may be incorporated into the Work:

a. Adams Rite: MS1850 Series 2. Requirements:

a. Provide narrow style aluminum door deadbolts as specified. Provide deadbolts with backset as required with full 1-13/32 inches (36 mm) throw deadbolt.

b. Provide manufacturer’s standard strikes unless extended lip strikes are necessary to protect trim.

2.09 CYLINDERS AND KEYING

A. Products that may be incorporated into the Work: 1. Schlage: Everest 29

B. Requirements: 1. Full Size Interchangeable Cylinders: Provide cylinders of quantity and type and with the

appropriate cam/tailpiece to be compatible with the locking hardware provided. Provide cylinder housings ready to accept 6-pin, Full-Size Interchangeable Cores (FSIC). a. Temporary Construction Keying: Provide each cylinder housing and/or lock lever with

keyed construction core during the construction period. Cores will remain property of the contractor and will be returned upon installation of owner’s permanent key system.



b. Permanent Cores: Provide factory keyed cores that are utility patented until at least 2029. Provide cores with a geographically exclusive factory-restricted keyway. Ship cores directly to owner’s representative. At substantial completion, accompany the owner’s representative while replacing temporary construction cores with the owner’s permanent key system.

2. Keys: Provide cylinder manufacturer’s standard keys. Keys shall be shipped separate from cores directly to owner’s representative. For estimating purposes, provide keys in the following quantities: a. Construction Control Keys: 2 each b. Construction Change Keys: 12 each c. Permanent Control Keys: 2 each d. Permanent Master Keys: 2 each e. Permanent Change Keys: 4 per core

2.10 EXIT DEVICES

A. Products that may be incorporated into the Work: 1. Von Duprin: 35/98 Series

B. Requirements: 1. Device Construction:

a. Exit device(s) shall have a mechanism case constructed of extruded aluminum or wrought stainless steel, base plates constructed of cold rolled or cast steel, push pad of extruded aluminum with stainless steel covering and end caps with flush mounted, sloped design. At full-glass doors, provide exit devices with no exposed fasteners or rivets visible through glass. Where required by stile width, provide narrow-stile type device.

b. Latchbolt: Provide Pullman-type deadlocking latch bolts constructed of stainless steel. Latch return springs shall be compression type.

c. Dogging Mechanism: where dogging or latch-retraction options are not specifically scheduled for non-fire rated doors, provide device with a hex-key activated hook-type dogging mechanism constructed of steel.

d. Plastic or nylon used for the push pad, or parts in the dogging mechanism or latchbolt mechanism are unacceptable.

e. Sound Dampening: Device shall be provided with factory-installed sound dampening materials.

f. Provide device type, function, and trim style as indicated in hardware schedules. 2. Where exit device(s) are provided for fire rated door, provide with fire listing and label

indicating “Fire Exit Hardware.” If device is mounted on wood doors, provide sex nuts and bolts.

3. Provide shim kits, filler plates, and other accessories as required for each opening. 4. Unless otherwise indicated in the sets, provide device with roller-type strike.

2.11 MECHANICAL DOOR CLOSERS

A. General: 1. Valves: Closers shall have separate valves for latch speed, main speed, and back check.

Valves shall be staked to prevent accidental removal. Internal Pressure Relief Valves (PRVs) are prohibited.

2. Provide the appropriate closer body, handing, and brackets to mount closer inside the building on the least-public side of the door. a. Where closers are to be mounted parallel arm, provide with heavy duty, fully forged

arms. b. Where closers are to be mounted regular arm and the opening can otherwise be

opened to 180 degrees, provide closer with the appropriate special templating to allow 180 degree door swing. Where a special template is not available for 180 degree swing, provide closer arm with integrated stop.



3. Integrated Stop Closer Arms: Where a closer with integrated stop is required, provide the appropriate closer and arm as follows: a. Parallel arm with spring-cushioned stop arm: Provide where door is otherwise able to

open to 95 degrees and requires a parallel arm mount closer. b. Parallel arm with dead stop arm: Provide where door is obstructed from opening to 95

degrees and requires a parallel arm mount closer. c. Regular arm with push side surface-mounted overhead stop: Provide where door

closer should mount on pull side of door. 4. Hold Open Arms: Provide closer arms with mechanical hold-opens as scheduled. 5. Provide closers with any special templates, brackets, plates, or other accessories required

for interface with header, door, wall, and other hardware. Provide closers with screw packs containing thru-bolts, machine screws, and wood screws.

6. Closers shall be provided with all-weather fluid and shall not require readjustment from 120 degrees F to -30 degrees F. Fluid shall be non-flaming and shall not fuel door or floor covering fires. Upon request, provide data indicating thermal properties of fluid.

7. Closers shall close and latch door when adjusted to meet accessibility requirements for door opening force: 8.5 lbs at exterior doors, 5 lbs at interior doors, and 15 lbs at labeled fire doors.

B. Heavy Duty Door Closers: 1. Products that may be incorporated into the Work:

a. LCN: 4010/4110 2. Requirements:

a. Closer Construction: Closer shall have cast iron body with 1-1/2 inch steel piston, double heat treated pinion, 5/8 inch bearing journals, and full complement needle bearings. Closer shall be adjustable from sizes 1 through 6.

b. Provide closers with spring size adjustment dial for ease of adjusting.

2.12 ARCHITECTURAL DOOR TRIM

A. Protection Plates 1. Products that may be incorporated into the Work:

a. Ives: 8400 Series 7308/7309 b. Rockwood: K1050 308/309 c. Trimco: K Series KE Series

2. Requirements: a. Provide .050 inch thick stainless steel protection plates with height as scheduled.

Plate shall have four beveled edges. Provide no screw holes and adhesive as required by door manufacturer’s fire labeling requirements. Otherwise provide plate manufacturer’s standard countersunk fasteners.

b. Provide plate with width as follows: 1) Pairs of Doors: Where door is scheduled with edge guards, provide plate to be

2 inches less door width, otherwise provide plate to be 1 inch less door width. 2) Single Doors: Provide plate to be 2 inches less door width on push side, pull

side mounted plates to be 1 inch less door width.

B. Door Stops and Holders 1. Products that may be incorporated into the Work:

a. Ives: WS407 WS439 b. Rockwood: 405/406 441H c. Trimco: 1270 W1211

2. Requirements: a. Provide stops and holders as indicated in the HW sets. b. Where wall bumpers are scheduled, provide concave rubber bumper where the

adjacent lever trim incorporates a push-button. Otherwise, provide convex rubber bumpers.



2.13 OVERHEAD STOPS AND HOLDERS

A. Products that may be incorporated into the Work: 1. Glynn Johnson: 100 Series 90 Series 2. Rixson-Firemark: 6 Series 9 Series

B. Requirements: 1. Provide overhead stops and holders as scheduled, sized per manufacturer’s

recommendations based on door width. 2. Provide concealed overhead stops with adjustable jamb bracket. 3. Where possible without conflicting with other hardware, mount surface overhead stops on

least public side of door. 4. Provide stops with any special templates, brackets, plates, or other accessories required for

interface with header, door, wall, and other hardware.

2.14 SADDLE AND PANIC THRESHOLDS

A. Manufacturers that may be incorporated into the Work: 1. Zero International 2. National Guard 3. Pemko

B. Requirements: 1. Provide saddle thresholds with length equal to the width of the opening. 2. Provide stainless steel machine screws and lead anchors for each threshold.

2.15 WEATHERSTRIP AND GASKET

A. General: 1. Provide weather strip and gasketing as scheduled. 2. Size weather strip and gasket to provide a continuous seal around opening and at meeting

stiles.

B. Perimeter Seals 1. Manufacturers that may be incorporated into the Work:

a. Zero b. National Guard c. Pemko

C. Astragals, Meeting Stiles, and Mullion Seals 1. Manufacturers that may be incorporated into the Work:


2. Requirements a. Where overlapping astragals are scheduled on exterior doors, provide with thru-bolts.

D. Door Bottoms 1. Manufacturers that may be incorporated into the Work:


E. Rain Drips 1. Manufacturers that may be incorporated into the Work:


2.16 MISCELLANEOUS HARDWARE



A. Silencers 1. Products that may be incorporated into the Work:

a. Ives: SR64 b. Rockwood: 608 c. Hager: 307D

2. Requirements: a. Where indicated on single openings, provide 3 each grey rubber silencers on lock

jamb. b. Where indicated on paired openings, provide 2 each grey rubber silencers on header.

2.17 HIGH SECURITY EMERGENCY KEY BOX

A. Products that may be incorporated into the Work: 1. Knox, Inc. 3200 Series x RMK

2. Substitutions as approved by Architect/Owner

B. Requirements: 1. Provide recess-mounted emergency key box as approved by the local fire jurisdiction. Key

box to be master-keyed as dictated by local fire jurisdiction.

2.18 KEY CONTROL CABINET

A. Products that may be incorporated into the Work: 1. Lund, Inc. 1200 Series

2. Substitutions as approved by Architect/Owner

B. Requirements: 1. Provide a key control system including envelopes, labels, and tags with self-locking key

clips, receipt forms, 3-way visible card index, temporary markers, permanent markers, and standard metal cabinet.

2. Provide complete cross-index system set up by Owner, and place keys on markers and hooks in the cabinet as determined by the final key schedule.

3. Provide hinged-panel type cabinet for wall mounting.

2.19 FINISHES

A. Match items to the manufacturer's standard color and texture finish for the latch and locksets (or push-pull units if no latch or locksets).

B. Provide quality of finish, including thickness of plating or coating (if any), composition, hardness, and other qualities complying with manufacturer's standards, but in no case less than specified by referenced standards for the applicable units of hardware.

C. The designations used in schedules and elsewhere to indicate hardware finishes are those listed in ANSI/BHMA A156.18, "Materials and Finishes," including coordination with the traditional U.S. finishes shown by certain manufacturers for their products.

D. The designations used in schedules and elsewhere to indicate hardware finishes are the industry-recognized standard commercial finishes, except as otherwise noted. 1. Brushed Chrome and/or Stainless Steel Appearance

a. Brushed Stainless Steel, no coating: ANSI 630. b. Satin Chrome, Clear Coated: ANSI 626, ANSI 652. c. Powder Coated Aluminum finish: ANSI 689. d. Saddle and Panic Thresholds: Mill Aluminum finish. e. Weatherstrip and Gasket: Clear Anodized Aluminum finish.

PART 3 - EXECUTION

3.01 EXAMINATION



A. Verify conditions of walls, flooring, doors, frames, and hardware are satisfactory for installation of hardware. 1. Prior to installing doors and hardware, wash down of masonry and painting or staining of

doors and frames shall be completed. 2. Verify that walls have blocking behind wall mounted stop locations. 3. Verify that flooring does not interfere with door or hardware operation. 4. Ensure that frames are installed plumb, square, and true. Verify that doors and frames are

properly sized and handed and are correctly prepared for hardware installation. 5. Verify function, quantity, type, hand, and finish of hardware to be installed with the approved

hardware schedule.

B. Conditions that do not allow proper installation of hardware shall be corrected before proceeding.

3.02 INSTALLATION

A. General 1. Install door hardware as detailed in the approved hardware schedule using only approved

fasteners and in accordance with manufacturer’s recommended procedures and methods. 2. Install hardware and signage at fire rated openings in accordance with NFPA 80

requirements.

B. Hardware Mounting Heights 1. Mount door hardware units at heights matching hollow metal frame manufacturer’s standard,

unless otherwise indicated or required to comply with governing regulations.

C. Clearances 1. Install doors, both rated and non-rated, in accordance with NFPA 80 requirements for door

clearances as follows: a. 1/8 inch between door and frame head and jambs for wood doors b. 3/16 inch between door and frame head and jambs for metal doors c. 1/8 inch at meeting stiles of pairs of doors. d. 3/4 inch undercut maximum.

D. Surface Mounted Door Closers 1. Install surface mounted door closers on room side of openings, except where prohibited by

scheduled hardware. Use appropriate arms, spacers, brackets, and accessories to properly install surface mounted door closers. Adjust spring power to the appropriate setting to ensure the doors reliably close under normal operating conditions.

E. Wall Mounted Door Stops And Holders 1. Locate wall mounted door stops at the appropriate height and location to properly contact

protruding door trim. 2. Where indicated in the HW Sets, mount floor stops at exterior doors as a wall stop.

F. Gasketing 1. Install gasketing to provide a continuous seal around the perimeter of the opening. Install

soffit mounted hardware using the proper brackets, spacers, and accessories to allow proper installation without cutting or notching gasketing material or mounting channels.

G. Overlapping Astragals 1. Install astragals at exterior doors using thru-bolts. 2. Where overlapping astragals are scheduled on out-swinging doors, provide for mounting on

the pull-side of the active leaf. Otherwise, provide for mounting on the push-side of the inactive leaf.

3. Notching astragal is not acceptable. Where strike lip conflicts with astragal, provide strike as specified in “Locks and Latches” article of this section.

H. Thresholds And Saddles



1. Trim, cut, and notch thresholds and saddles neatly to minimally fit the profile of the door frame. Thresholds and saddles shall be set in full bed of butyl-rubber or polyisobutylene mastic sealant.

3.03 FIELD QUALITY CONTROL

A. Architectural Hardware Consultant: Architect will engage a qualified Architectural Hardware Consultant to perform inspections and to prepare inspection reports.

B. Architectural Hardware Consultant will inspect door hardware and state in each report whether installed work complies with or deviates from requirements, including whether door hardware is properly installed and adjusted.

3.04 ADJUSTING

A. After building HVAC system is balanced and adjusted, conduct final adjustment of door closers. Verify spring power of the surface mounted door closer is properly adjusted to close and latch the door and to comply with the opening force requirements of ANSI A117.1 as follows: 1. Doors with Closers shall take five (5) seconds to close from 90 degrees to 12 degrees. 2. Interior, non-fire rated swinging doors shall open with a maximum of 5 lbs of pressure. 3. Exterior doors and fire rated doors shall open with the minimum amount of pressure required

to positively close and latch the door.

3.05 CLEANING AND PROTECTION

A. Clean adjacent surfaces soiled by door hardware installation.

B. Clean operating items as necessary to restore proper function and finish.

C. Provide final protection and maintain conditions that ensure that door hardware is without damage or deterioration at time of Substantial Completion.

3.06 SCHEDULE

A. The following schedule of hardware sets shall be considered a guide and the supplier is cautioned to refer to general conditions, special conditions, and the full requirements of this section. It shall be the hardware supplier's responsibility to furnish all required hardware.

B. Where items of hardware are not definitely or correctly specified and are required for completion of the Work, a written statement of such omission, error, conflict, or other discrepancy shall be sent to the Architect, prior to date specified for receipt of bids, for clarification by addendum.

C. Adjustments to the Contract Sum will not be allowed for omissions or items of hardware not clarified prior to bid opening.



SpeXtra: 296038

HW SET: 100 EXTERIOR HM; ELECTRICAL ROOM PANIC SINGLE

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA PANIC HARDWARE 98-NL 626 VON 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET CONSTRUCTION CORE 23-030-ICX 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 4111 AVB SCUSH TBWMS 689 LCN 1 EA RAIN DRIP CAP 142A AL ZER 1 EA PERIMETER SEALS 429A A ZER 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SHOE 153A A ZER 1 EA DOOR SWEEP 8198AA AA ZER 1 EA THRESHOLD 655A SSMSLA-10 A ZER 1 SET ELECTRICAL RM SIGNAGE BY SIGNAGE VENDOR B/O

HW SET: 101 EXTERIOR HM; STOREROOM LOCK PR

2 EA CONTINUOUS HINGE 112HD 628 IVE 1 SET SELF LATCHING BOLT FB51P / FB61P 630 IVE 1 EA STOREROOM LOCK L9080T 06A 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA COORDINATOR COR X FL (MB AS REQ' BY ADJACENT HDWR) 628 IVE 2 EA SURFACE CLOSER 4111 AVB SCUSH TBWMS 689 LCN 1 EA RAIN DRIP CAP 142A AL ZER 1 EA PERIMETER SEALS 429A A ZER 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA ASTRAGAL 41AA AA ZER 1 EA ASTRAGAL SEALS 8193AA AA ZER 2 EA DOOR SHOE 153A A ZER 2 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A SSMSLA-10 A ZER

A) MOUNT OVERLAPPING ASTRAGAL ON EXTERIOR SIDE OF OPENING AND ASTRAGAL SEALS ON INTERIOR SIDE

OF OPENING.



HW SET: 102 EXTERIOR HM; ENTRANCE LOCK SGL (DOORBELL)

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA ENTRANCE LOCK W/ DB L9453T 06A L583-363 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 4111 AVB SCUSH TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA RAIN DRIP CAP 142A AL ZER 1 EA PERIMETER SEALS 429A A ZER 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SHOE 153A A ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A SSMSLA-10 A ZER 1 EA DOOR BELL BY ELECTRICAL B/O

HW SET: 103 EXTERIOR HM; ENTRANCE LOCK SGL

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA ENTRANCE LOCK W/ DB L9453T 06A L583-363 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 4111 AVB SCUSH TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA RAIN DRIP CAP 142A AL ZER 1 EA PERIMETER SEALS 429A A ZER 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SHOE 153A A ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 655A SSMSLA-10 A ZER

HW SET: 200 SERVICE AREA; SELF-CLOSING STOREROOM SGL (WALL STOP)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA STOREROOM LOCK ND80TD RHO 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 544A MSLA-10 A ZER



HW SET: 201 SERVICE AREA; SINGLE TOILET/LOCKER

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA OFFICE W/SIM RETRACT L9056T 06A L283-722 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 1450 RW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 544A MSLA-10 A ZER 1 SET RESTROOM SIGNAGE BY SIGNAGE VENDOR B/O

HW SET: 202 SERVICE AREA; LOCKING PUSH PULL SGL

1 SET HINGE(S) 5BB1HW SERIES 652 IVE 1 EA SGL CYL DEADBOLT B660T 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA PUSH PLATE 8200 4" X 16" CFC 630 IVE 1 EA PULL PLATE 8303 10" 4" X 16" CFC 630 IVE 1 EA SURFACE CLOSER 4050 HW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 24" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 544A MSLA-10 A ZER

HW SET: 203 SERVICE AREA; PUSH PULL SGL (HOLD OPEN)

1 SET HINGE(S) 5BB1HW SERIES 652 IVE 1 EA PUSH PLATE 8200 4" X 16" 630 IVE 1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE 1 EA SURFACE CLOSER 4050 HW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 544A MSLA-10 A ZER



HW SET: 204 SERVICE AREA; PUSH PULL SGL (RESTROOM)

1 SET HINGE(S) 5BB1HW SERIES 652 IVE 1 EA PUSH PLATE 8200 4" X 16" 630 IVE 1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE 1 EA SURFACE CLOSER 4050 RW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 EA PERIMETER SEALS 488S-BR S-Br ZER 1 EA DOOR SWEEP 39A A ZER 1 EA THRESHOLD 544A MSLA-10 A ZER 1 SET RESTROOM SIGNAGE BY SIGNAGE VENDOR B/O

HW SET: 300 INTERIOR; SELF-CLOSING STOREROOM SGL (OVERHEAD STOP)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA STOREROOM LOCK AL80TD SAT 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA OVERHEAD STOP 450S 630 GLY 1 EA SURFACE CLOSER 1450 RW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 301 INTERIOR; SELF-CLOSING STOREROOM SGL (WALL STOP)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA STOREROOM LOCK AL80TD SAT 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 1450 RW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 302 INTERIOR; STOREROOM SGL (KICKPLATE)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA STOREROOM LOCK AL80TD SAT 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O



HW SET: 303 INTERIOR; STOREROOM SGL

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA STOREROOM LOCK AL80TD SAT 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 304 INTERIOR; SELF-CLOSING ENTRANCE LOCK SGL (HOLD OPEN)

1 SET HINGE(S) 5BB1HW SERIES 652 IVE 1 EA ENTRANCE LOCK ND53TD RHO 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 4050 HW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 24" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 305 INTERIOR; SELF-CLOSING ENTRANCE LOCK SGL (HOLD OPEN)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA ENTRANCE LOCK ND53TD RHO 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA SURFACE CLOSER 1450 HW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 306 INTERIOR; OFFICE LOCK SGL

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA OFFICE LOCK AL50TD SAT 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O

HW SET: 307 INTERIOR; PRIVACY LOCK SGL

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA PRIVACY LOCK AL40S SAT 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA WARDROBE HOOK 582 626 IVE



HW SET: 308 INTERIOR; PASSAGE LATCH SGL

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA PASSAGE SET AL10S SAT 626 SCH 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O

HW SET: 309 INTERIOR; PUSH PULL SGL (HOLD OPEN)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA PUSH PLATE 8200 4" X 16" 630 IVE 1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE 1 EA SURFACE CLOSER 1450 HW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O

HW SET: 310 INTERIOR; PUSH PULL SGL (RESTROOM)

1 SET HINGE(S) 5BB1 SERIES 652 IVE 1 EA PUSH PLATE 8200 4" X 16" 630 IVE 1 EA PULL PLATE 8303 10" 4" X 16" 630 IVE 1 EA SURFACE CLOSER 1450 RW/PA TBWMS 689 LCN 1 EA KICK PLATE 8400 10" X 2" LDW B-CS 630 IVE 1 EA WALL STOP WS406/407CCV 630 IVE 1 SET SILENCERS / GASKET BY FRAME MANUFACTURER TBD B/O 1 SET RESTROOM SIGNAGE BY SIGNAGE VENDOR B/O

HW SET: AL-100 EXTERIOR STOREFRONT; PANIC ENTRY PAIR

2 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA PANIC HARDWARE CD-9849/3549-EO 626 VON 1 EA PANIC HARDWARE CD-9849/3549-NL-OP 626 VON 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET CONSTRUCTION CORE 23-030-ICX 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 2 EA LONG DOOR PULL 9264F 72" 56" A 630 IVE 2 EA OVERHEAD STOP 100S ADJ 630 GLY 2 EA SURFACE CLOSER 4111 AVB EDA TBWMS 689 LCN 2 SET BRACKETS AS REQUIRED TO INSTALL CLOSER TBD LCN 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 1 SET ASTRAGAL SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 4 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O

A) PROVIDE DOUBLE ROW OF PILE GASKETING AND MOUNT DOOR SWEEP ON BOTH SIDES OF EACH DOOR LEAF

FOR PROTECTION FROM DRIVING WIND.



HW SET: AL-101 EXTERIOR STOREFRONT; PANIC ENTRY PAIR WITH NON-EGRESS INACTIVE LEAF

2 EA CONTINUOUS HINGE 112HD 628 IVE 2 EA MANUAL FLUSH BOLT FB458 626 IVE 1 EA PANIC HARDWARE CD-9849/3549-NL-OP 626 VON 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET CONSTRUCTION CORE 23-030-ICX 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA LONG DOOR PULL 9264F 72" 56" A 630 IVE 1 EA SURFACE CLOSER 4111 AVB EDA TBWMS 689 LCN 1 SET BRACKETS AS REQUIRED TO INSTALL CLOSER TBD LCN 2 EA FLOOR STOP FS18L BLK IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 1 SET ASTRAGAL SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 4 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O



HW SET: AL-102 EXTERIOR STOREFRONT; PANIC ENTRY SINGLE

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA PANIC HARDWARE CD-98/35-NL-OP 626 VON 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET CONSTRUCTION CORE 23-030-ICX 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA LONG DOOR PULL 9264F 72" 56" A 630 IVE 1 EA OVERHEAD STOP 100S ADJ 630 GLY 1 EA SURFACE CLOSER 4111 AVB EDA TBWMS 689 LCN 1 SET BRACKETS AS REQUIRED TO INSTALL CLOSER TBD LCN 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 4 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O





HW SET: AL-103 EXTERIOR STOREFRONT; LOCKING PUSH PULL SINGLE

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA MORTISE DEADBOLT MS1850 SERIES 626 ADA 1 EA EXIT INDICATOR 4089 626 ADA 1 EA THUMBTURN CYLINDER 09-900 NH XB11-720 626 SCH 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET CONSTRUCTION CORE 23-030-ICX 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA PUSH BAR 9100HD A 630 IVE 1 EA LONG DOOR PULL 9264F 72" 56" A 630 IVE 1 EA OVERHEAD STOP 100S ADJ 630 GLY 1 EA SURFACE CLOSER 4111 AVB EDA TBWMS 689 LCN 1 SET BRACKETS AS REQUIRED TO INSTALL CLOSER TBD LCN 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 4 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O


FOR PROTECTION FROM DRIVING WIND. B) INSTALL THUMBTURN CYLINDER ON INSIDE FOR SINGLE-MOTION EGRESS AND KEYED CYLINDER ON

EXTERIOR FOR KEYED ENTRY.

HW SET: AL-200 SERVICE AREA STOREFRONT; SELF-CLOSING PASSAGE SINGLE

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA PASSAGE LATCH BODY 8825 SERIES 626 ACC 1 EA PASSAGE LATCH TRIM L9010 06A LESS LOCK CASE 626 SCH 1 EA CONCEALED CLOSER 2030 SERIES 689 LCN 1 EA DOOR STOPS WS407CCV / FS439 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O

A) IF DOOR HAS LOCKING STILE AT LEAST 5 INCHES WIDE, CHANGE NARROW STILE PASSAGE LATCH BODY AND

TRIM INDICATED ABOVE WITH SCHLAGE ND10S RHO CYLINDRICAL LOCKSET.

HW SET: AL-201 SERVICE AREA STOREFRONT; PUSH PULL SINGLE

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 SET LONG DOOR PULL PR 9264F 72" 56" N 630 IVE 1 EA CONCEALED CLOSER 2030 SERIES 689 LCN 1 EA DOOR STOPS WS407CCV / FS439 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA DOOR SWEEP BY DOOR/FRAME MANUFACTURER TBD B/O 1 EA THRESHOLD BY DOOR/FRAME MANUFACTURER TBD B/O



HW SET: AL-300 INTERIOR STOREFRONT; SELF-CLOSING OFFICE (HOLD OPEN)

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA OFFICE LOCK BODY 8856 SERIES 626 ACC 1 EA OFFICE LOCK TRIM L9050L 06A LESS LOCK CASE 626 SCH 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA CONCEALED CLOSER 2030 H SERIES 689 LCN 1 EA DOOR STOPS WS407CCV / FS439 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O

A) IF DOOR HAS LOCKING STILE AT LEAST 5 INCHES WIDE, CHANGE NARROW STILE OFFICE LOCK BODY AND

TRIM INDICATED ABOVE WITH SCHLAGE ND53TD RHO CYLINDRICAL LOCKSET.

HW SET: AL-301 INTERIOR STOREFRONT; OFFICE (NO CLOSER)

1 EA CONTINUOUS HINGE 112HD 628 IVE 1 EA OFFICE LOCK BODY 8856 SERIES 626 ACC 1 EA OFFICE LOCK TRIM L9050L 06A LESS LOCK CASE 626 SCH 1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 EA DOOR STOPS WS407CCV / FS439 630 IVE 1 SET PERIMETER SEALS BY DOOR/FRAME MANUFACTURER TBD B/O

A) IF DOOR HAS LOCKING STILE AT LEAST 5 INCHES WIDE, CHANGE NARROW STILE OFFICE LOCK BODY AND

TRIM INDICATED ABOVE WITH SCHLAGE ND50TD RHO CYLINDRICAL LOCKSET.

HW SET: OHD-100 OVERHEAD/COILING DOOR

1 SET ALL HARDWARE BY DOOR/FRAME MANUFACTURER B/O

HW SET: OHD-101 OVERHEAD/COILING DOOR; CAR SENSOR

1 SET ALL HARDWARE BY DOOR/FRAME MANUFACTURER B/O A) DOOR TO OPERATE VIA MICROWAVE SENSORS ON EITHER SIDE OF OPENING DURING BUSINESS HOURS.

HW SET: OHD-102 OVERHEAD/COILING DOOR; KEY PAD

1 EA KEY PAD READER BY SECURITY / ELECTRICAL TBD B/O 1 SET REMAINING HARDWARE BY DOOR/FRAME MANUFACTURER B/O



HW SET: SL-100 EXTERIOR SLIDER; AUTOMATIC SLIDING DOOR

1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 SET REMAINING HARDWARE BY DOOR/FRAME MANUFACTURER B/O



HW SET: SL-300 INTERIOR SLIDER; AUTOMATIC SLIDING DOOR

1 SET CYLINDER(S) AS REQ'D BY LOCKING HARDWARE 626 SCH 1 SET PERMENANT CORE 23-030 EV29T 626 SCH 1 SET REMAINING HARDWARE BY DOOR/FRAME MANUFACTURER B/O



GLAZING 088000 1

SECTION 088000 - GLAZING

PART 1 - GENERAL

1.1 SUMMARY

A. This Section includes glazing for the following products and applications, including those specified in other Sections where glazing requirements are specified by reference to this Section:

1. Windows. 2. Doors. 3. Glazed curtain walls. 4. Glazed entrances. 5. Interior borrowed lites. 6. Storefront framing.

1.2 DEFINITIONS

A. Interspace: Space between lites of an insulating-glass unit that contains dehydrated air or a specified gas.

B. Deterioration of Coated Glass: Defects developed from normal use that are attributed to the manufacturing process and not to causes other than glass breakage and practices for maintaining and cleaning coated glass contrary to manufacturer's written instructions. Defects include peeling, cracking, and other indications of deterioration in metallic coating.

C. Deterioration of Insulating Glass: Failure of hermetic seal under normal use that is attributed to the manufacturing process and not to causes other than glass breakage and practices for maintaining and cleaning insulating glass contrary to manufacturer's written instructions. Evidence of failure is the obstruction of vision by dust, moisture, or film on interior surfaces of glass.

D. Deterioration of Laminated Glass: Defects developed from normal use that are attributed to the manufacturing process and not to causes other than glass breakage and practices for maintaining and cleaning laminated glass contrary to manufacturer's written instructions. Defects include edge separation, delamination materially obstructing vision through glass, and blemishes exceeding those allowed by referenced laminated-glass standard.


A. General: Provide glazing systems capable of withstanding normal thermal movement and wind and impact loads (where applicable) without failure, including loss or glass breakage attributable to the following: defective manufacture, fabrication, and installation; failure of sealants or gaskets to remain watertight and airtight; deterioration of glazing materials; or other defects in construction.

B. Glass Design: Glass thickness designations indicated are minimums and are for detailing only. Confirm glass thicknesses by analyzing Project loads and in-service conditions. Provide glass lites in the thickness designations indicated for various size openings, but not less than thicknesses and in strengths (annealed or heat treated) required to meet or exceed the following criteria:

1. Glass Thicknesses: Select minimum glass thicknesses to comply with ASTM E 1300, according to the following requirements:


GLAZING 088000 2

a. Specified Design Wind Loads: Not less than wind loads applicable to Project as required by ASCE 7 "Minimum Design Loads for Buildings and Other Structures": Section 6.0 "Wind Loads."

b. Probability of Breakage for Vertical Glazing: 8 lites per 1000 for lites set vertically or not more than 15 degrees off vertical and under wind action.

1) Load Duration: 60 seconds or less.

c. Minimum Glass Thickness for Exterior Lites: Not less than ¼ inch. d. Thickness of Tinted and Heat-Absorbing Glass: Provide the same thickness for each tint

color indicated throughout Project.

C. Thermal Movements: Provide glazing that allows for thermal movements resulting from the following maximum change (range) in ambient and surface temperatures acting on glass framing members and glazing components. Base engineering calculation on surface temperatures of materials due to both solar heat gain and nighttime-sky heat loss.

1. Temperature Change (Range): 120 deg F, ambient; 180 deg F, material surfaces.

D. Thermal and Optical Performance Properties: Provide glass with performance properties specified based on manufacturer's published test data, as determined according to procedures indicated below:

1. For monolithic-glass lites, properties are based on units with lites of thickness indicated. 2. For laminated-glass lites, properties are based on products of construction indicated. 3. For insulating-glass units, properties are based on units of thickness indicated for overall unit

and for each lite ¼ inch and a nominal 1/2-inch- wide interspace. 4. Center-of-Glass Values: Based on using LBL-44789 WINDOW 5.0 computer program for the

following methodologies:

a. U-Factors: NFRC 100 expressed as Btu/ sq. ft. x h x deg F. b. Solar Heat Gain Coefficient: NFRC 200. c. Solar Optical Properties: NFRC 300.

1.4 SUBMITTALS

A. Product Data: For each glass product and glazing material indicated.

B. Samples: 12-inch- square, for each type of glass product indicated, other than monolithic clear float glass.

C. Glazing Schedule: Use same designations indicated on Drawings.

D. Preconstruction Adhesion and Compatibility Test Report: From glazing sealant manufacturer.


A. Preconstruction Adhesion and Compatibility Testing: Submit to elastomeric glazing sealant manufacturers, for testing according to ASTM C 1087, samples of each glazing material type, tape sealant, gasket, glazing accessory, and glass-framing member that will contact or affect elastomeric glazing sealants:

B. Glazing for Fire-Rated Door Assemblies: Glazing for assemblies that comply with NFPA 80 and that are listed and labeled by a testing and inspecting agency acceptable to authorities having jurisdiction, for fire ratings indicated, based on testing according to NFPA 257.


GLAZING 088000 3

C. Safety Glazing Products: Comply with testing requirements in 16 CFR 1201 and, for wired glass, ANSI Z97.1.

D. Glazing Publications: Comply with published recommendations of glass product manufacturers and organizations below, unless more stringent requirements are indicated. Refer to these publications for glazing terms not otherwise defined in this Section or in referenced standards.

1. GANA Publications: GANA Laminated Division's "Laminated Glass Design Guide" and GANA's "Glazing Manual."

2. AAMA Publications: AAMA GDSG-1, "Glass Design for Sloped Glazing," and AAMA TIR-A7, "Sloped Glazing Guidelines."

3. IGMA Publication for Sloped Glazing: IGMA TB-3001, "Sloped Glazing Guidelines." 4. IGMA Publication for Insulating Glass: SIGMA TM-3000, "Glazing Guidelines for Sealed

Insulating Glass Units."

E. Insulating-Glass Certification Program: Permanently marked either on spacers or on at least one component lite of units with appropriate certification label of the Insulating Glass Certification Council.

1.6 WARRANTY

A. Manufacturer's Special Warranty for Coated-Glass Products: Manufacturer's standard form, made out to Owner and signed by coated-glass manufacturer agreeing to replace coated-glass units that deteriorate as defined in "Definitions" Article, f.o.b. the nearest shipping point to Project site, within specified warranty period indicated below.


B. Manufacturer's Special Warranty on Laminated Glass: Manufacturer's standard form, made out to Owner and signed by laminated-glass manufacturer agreeing to replace laminated-glass units that deteriorate as defined in "Definitions" Article, f.o.b. the nearest shipping point to Project site, within specified warranty period indicated below.


C. Manufacturer's Special Warranty on Insulating Glass: Manufacturer's standard form, made out to Owner and signed by insulating-glass manufacturer agreeing to replace insulating-glass units that deteriorate as defined in "Definitions" Article, f.o.b. the nearest shipping point to Project site, within specified warranty period indicated below.


PART 2 - PRODUCTS

2.1 MANUFACTURERS

A. In other Part 2 articles where titles below introduce lists, the following requirements apply to product selection:

1. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, products specified.

2. Products: Subject to compliance with requirements, provide one of the products specified. 3. Product: Subject to compliance with requirements, provide product specified.


GLAZING 088000 4

4. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, manufacturers specified.

5. Manufacturers: Subject to compliance with requirements, provide products by one of the manufacturers specified.

2.2 GLASS PRODUCTS

A. Annealed Float Glass: ASTM C 1036, Type I (transparent flat glass), Quality-Q3; of class indicated.

1. Ultra-Clear (Low-Iron) Float Glass: Class I (clear); with a minimum 91 percent visible light transmission and a minimum solar heat gain coefficient of 0.87.

a. Products:

1) AFG Industries Inc.; Krystal Klear. 2) Pilkington Building Products North America; Optiwhite. 3) PPG Industries, Inc.; Starphire.

B. Heat-Treated Float Glass: ASTM C 1048; Type I (transparent flat glass); Quality-Q3; of class, kind, and condition indicated.

1. Fabrication Process: By horizontal (roller-hearth) process with roll-wave distortion parallel to bottom edge of glass as installed, unless otherwise indicated.

2. Provide Kind HS (heat-strengthened) float glass in place of annealed float glass where needed to resist thermal stresses induced by differential shading of individual glass lites and to comply with glass design requirements specified in Part 1 "Performance Requirements" Article.

3. For uncoated glass, comply with requirements for Condition A. 4. Provide Kind FT (fully tempered) float glass in place of annealed or Kind HS (heat-

strengthened) float glass where safety glass is indicated.

C. Ceramic-Coated Spandrel Glass: ASTM C 1048, Condition B (spandrel glass, one surface ceramic coated), Type I (transparent flat glass), Quality-Q3, and complying with other requirements specified.

1. Fallout Resistance: Provide spandrel units identical to those passing the fallout-resistance test for spandrel glass specified in ASTM C 1048.

D. Wired Glass: ASTM C 1036, Type II (patterned and wired flat glass), Class 1 (clear), Quality-Q-6; and of form and mesh pattern specified.

E. Insulating-Glass Units, General: Factory-assembled units consisting of sealed lites of glass separated by a dehydrated interspace, and complying with ASTM E 774 for Class CBA units and with requirements specified in this Article and in Part 2 "Insulating-Glass Units" Article.

1. Provide Kind HS (heat-strengthened) float glass in place of annealed glass where needed to resist thermal stresses induced by differential shading of individual glass lites and to comply with glass design requirements specified in Part 1 "Performance Requirements" Article.

2. Overall Unit Thickness and Thickness of Each Lite: Dimensions indicated for insulating-glass units are nominal and the overall thicknesses of units are measured perpendicularly from outer surfaces of glass lites at unit's edge.

3. Sealing System: Dual seal. 4. Spacer Specifications: Manufacturer's standard spacer material and construction. 5. Spacer Specifications: Manufacturer's standard spacer material and construction complying

with the following requirements:

a. Spacer Material: Aluminum with mill or clear anodic finish. b. Corner Construction: Manufacturer's standard corner construction.


GLAZING 088000 5

2.3 GLAZING GASKETS

A. Dense Compression Gaskets: Molded or extruded gaskets of material indicated below, complying with standards referenced with name of elastomer indicated below, and of profile and hardness required to maintain watertight seal:

1. Neoprene, ASTM C 864. 2. EPDM, ASTM C 864. 3. Silicone, ASTM C 1115. 4. Thermoplastic polyolefin rubber, ASTM C 1115. 5. Any material indicated above.

B. Soft Compression Gaskets: Extruded or molded, closed-cell, integral-skinned gaskets of material indicated below; complying with ASTM C 509, Type II, black; and of profile and hardness required to maintain watertight seal:

1. Neoprene. 2. EPDM. 3. Silicone. 4. Thermoplastic polyolefin rubber. 5. Any material indicated above.

2.4 GLAZING SEALANTS

A. General: Provide products of type indicated, complying with the following requirements:

1. Compatibility: Select glazing sealants that are compatible with one another and with other materials they will contact, including glass products, seals of insulating-glass units, and glazing channel substrates, under conditions of service and application, as demonstrated by sealant manufacturer based on testing and field experience.

2. Suitability: Comply with sealant and glass manufacturers' written instructions for selecting glazing sealants suitable for applications indicated and for conditions existing at time of installation.

3. VOC Content: For sealants used inside of the weatherproofing system, not more than 250 g/L when calculated according to 40 CFR 59, Subpart D (EPA Method 24).

4. Colors of Exposed Glazing Sealants: As selected by Architect from manufacturer's full range.

5. Neutral-Curing Silicone Glazing Sealants:

a. Products:

b. Type and Grade: S (single component) and NS (nonsag). c. Class: 25. d. Use Related to Exposure: NT (nontraffic). e. Uses Related to Glazing Substrates: M, G, A, and, as applicable to glazing substrates

indicated, O.

B. Glazing Sealants for Fire-Resistive Glazing Products: Identical to products used in test assemblies to obtain fire-protection rating.

2.5 GLAZING TAPES

A. Back-Bedding Mastic Glazing Tapes: Preformed, butyl-based elastomeric tape with a solids content of 100 percent; nonstaining and nonmigrating in contact with nonporous surfaces; with or without spacer rod as recommended in writing by tape and glass manufacturers for application indicated; packaged


GLAZING 088000 6

on rolls with a release paper backing; and complying with ASTM C 1281 and AAMA 800 for products indicated below:

1. AAMA 804.3 tape, where indicated. 2. AAMA 806.3 tape, for glazing applications in which tape is subject to continuous pressure. 3. AAMA 807.3 tape, for glazing applications in which tape is not subject to continuous pressure.

B. Expanded Cellular Glazing Tapes: Closed-cell, PVC foam tapes; factory coated with adhesive on both surfaces; packaged on rolls with release liner protecting adhesive; and complying with AAMA 800 for the following types:

1. Type 1, for glazing applications in which tape acts as the primary sealant. 2. Type 2, for glazing applications in which tape is used in combination with a full bead of liquid

sealant.

2.6 MISCELLANEOUS GLAZING MATERIALS

A. General: Provide products of material, size, and shape complying with referenced glazing standard, requirements of manufacturers of glass and other glazing materials for application indicated, and with a proven record of compatibility with surfaces contacted in installation.

B. Cleaners, Primers, and Sealers: Types recommended by sealant or gasket manufacturer.

C. Setting Blocks: Elastomeric material with a Shore, Type A durometer hardness of 85, plus or minus 5.

D. Spacers: Elastomeric blocks or continuous extrusions with a Shore, Type A durometer hardness required by glass manufacturer to maintain glass lites in place for installation indicated.

E. Edge Blocks: Elastomeric material of hardness needed to limit glass lateral movement (side walking).

F. Cylindrical Glazing Sealant Backing: ASTM C 1330, Type O (open-cell material), of size and density to control glazing sealant depth and otherwise produce optimum glazing sealant performance.

G. Perimeter Insulation for Fire-Resistive Glazing: Identical to product used in test assembly to obtain fire-resistance rating.

2.7 FABRICATION OF GLAZING UNITS

A. Fabricate glazing units in sizes required to glaze openings indicated for Project, with edge and face clearances, edge and surface conditions, and bite complying with written instructions of product manufacturer and referenced glazing publications, to comply with system performance requirements.

2.8 MONOLITHIC FLOAT-GLASS UNITS

A. Uncoated Clear Float-Glass Units: Class 1 (clear) annealed or Kind HS (heat-strengthened) float glass where heat strengthening is required to resist thermal stresses induced by differential shading of individual glass lites and to comply with system performance requirements.

1. Thickness: ¼".


GLAZING 088000 7

2.9 MONOLITHIC WIRED-GLASS UNITS

A. Polished Wired-Glass Units: Form 1 (wired glass, polished both sides), Quality-Q6, Mesh Square, 1/4 -inch thick.

1. Manufacturers:

a. Asahi/AMA Glass Corp.; affiliated with AFG Industries, Inc. b. Central Glass Co., Ltd.; distributed by Northwestern Industries Inc. c. Pilkington Sales (North America) Ltd.

2.10 INSULATING-GLASS UNITS

A. Passive Solar Low-E Insulating-Glass Units :

1. Products: As indicated.

2. Overall Unit Thickness and Thickness of Each Lite: 1" and ¼". 3. Interspace Content: Argon. 4. Outdoor Lite: Class 1 (clear) float glass.

a. Tint Color: as indicated. b. Annealed, Kind FT (fully tempered). c. Self-Cleaning, Low-Maintenance Coating: Pyrolytic coating on first surface.

5. Indoor Lite: Class 1 (clear) float glass.

a. Annealed Kind FT (fully tempered). 6. Low-E-Coated Film: Suspended in the interspace.

PART 3 - EXECUTION

3.1 GLAZING

A. General: Comply with combined written instructions of manufacturers of glass, sealants, gaskets, and other glazing materials, unless more stringent requirements are indicated, including those in referenced glazing publications.

1. Glazing channel dimensions, as indicated on Drawings, provide necessary bite on glass, minimum edge and face clearances, and adequate sealant thicknesses, with reasonable tolerances. Adjust as required by Project conditions during installation.

2. Protect glass edges from damage during handling and installation. Remove damaged glass from Project site and legally dispose of off Project site. Damaged glass is glass with edge damage or other imperfections that, when installed, could weaken glass and impair performance and appearance.

3. Apply primers to joint surfaces where required for adhesion of sealants, as determined by preconstruction sealant-substrate testing.

4. Install setting blocks in sill rabbets, sized and located to comply with referenced glazing publications, unless otherwise required by glass manufacturer. Set blocks in thin course of compatible sealant suitable for heel bead.

5. Do not exceed edge pressures stipulated by glass manufacturers for installing glass lites. 6. Provide spacers for glass lites where length plus width is larger than 50 inches.


GLAZING 088000 8

7. Provide edge blocking where indicated or needed to prevent glass lites from moving sideways in glazing channel, as recommended in writing by glass manufacturer and according to requirements in referenced glazing publications.

B. Tape Glazing: Position tapes on fixed stops so that, when compressed by glass, their exposed edges are flush with or protrude slightly above sightline of stops. Install tapes continuously, but not necessarily in one continuous length. Do not stretch tapes to make them fit opening.

1. Cover vertical framing joints by applying tapes to heads and sills first and then to jambs. Cover horizontal framing joints by applying tapes to jambs and then to heads and sills.

2. Place joints in tapes at corners of opening with adjoining lengths butted together, not lapped. Seal joints in tapes with compatible sealant approved by tape manufacturer.

3. Apply heel bead of elastomeric sealant. 4. Center glass lites in openings on setting blocks and press firmly against tape by inserting dense

compression gaskets formed and installed to lock in place against faces of removable stops. Start gasket applications at corners and work toward centers of openings.

5. Apply cap bead of elastomeric sealant over exposed edge of tape.

C. Gasket Glazing (Dry): Fabricate compression gaskets in lengths recommended by gasket manufacturer to fit openings exactly, with allowance for stretch during installation.

1. Insert soft compression gasket between glass and frame or fixed stop so it is securely in place with joints miter cut and bonded together at corners.

2. Center glass lites in openings on setting blocks and press firmly against soft compression gasket by inserting dense compression gaskets formed and installed to lock in place against faces of removable stops. Start gasket applications at corners and work toward centers of openings. Compress gaskets to produce a weathertight seal without developing bending stresses in glass. Seal gasket joints with sealant recommended by gasket manufacturer.

3. Install gaskets so they protrude past face of glazing stops.

D. Sealant Glazing (Wet): Install continuous spacers, or spacers combined with cylindrical sealant backing, between glass lites and glazing stops to maintain glass face clearances and to prevent sealant from extruding into glass channel and blocking weep systems until sealants cure. Secure spacers or spacers and backings in place and in position to control depth of installed sealant relative to edge clearance for optimum sealant performance.

1. Force sealants into glazing channels to eliminate voids and to ensure complete wetting or bond of sealant to glass and channel surfaces.

2. Tool exposed surfaces of sealants to provide a substantial wash away from glass.

3.2 CLEANING AND PROTECTION

A. Protect exterior glass from damage immediately after installation by attaching crossed streamers to framing held away from glass. Do not apply markers to glass surface. Remove nonpermanent labels, and clean surfaces. Protect glass from contact with contaminating substances resulting from construction operations, including weld splatter. If, despite such protection, contaminating substances do come into contact with glass, remove substances immediately as recommended by glass manufacturer.

B. Remove and replace glass that is broken, chipped, cracked, or abraded or that is damaged from natural causes, accidents, and vandalism, during construction period.



MIRRORS 088300 1

SECTION 088300 - MIRRORS

PART 1 - GENERAL

1.1 SUMMARY

A. This Section includes the following:

1. Annealed monolithic glass mirrors. 2. Tempered glass mirrors qualifying as safety glazing.

1.2 SUBMITTALS

A. Product Data: For mirror mastic.

B. Shop Drawings: Include mirror elevations, edge details, mirror hardware, and attachments to other work.

C. Samples: For each type of mirror product required, in the form indicated below:

1. Mirrors, 12 inches square, including edge treatment on 2 adjoining edges. 2. Mirror clips. 3. Mirror trim, 12 inches long.

D. Product Certificates: For each type of mirror and mirror mastic, signed by product manufacturer.

E. Mirror Mastic Compatibility Test Reports: From mirror manufacturer.


A. Glazing Publications: Comply with GANA's "Glazing Manual" and GANA Mirror Division's "Mirrors, Handle with Extreme Care: Tips for the Professional on the Care and Handling of Mirrors" unless more stringent requirements are indicated

B. Safety Glazing Products: For tempered mirrors, provide products complying with testing requirements in 16 CFR 1201 for Category II materials.

C. Preconstruction Mirror Mastic Compatibility Test: Submit mirror mastic products to mirror manufacturer for testing to determine compatibility of mastic with mirror backing and substrates on which mirrors are installed.

1.4 DELIVERY, STORAGE, AND HANDLING

A. Comply with mirror manufacturer's written instructions for shipping, storing, and handling mirrors as needed to prevent deterioration of silvering, damage to edges, and abrasion of glass surfaces and applied coatings. Store indoors, protected from moisture including condensation.


MIRRORS 088300 2

1.5 WARRANTY

A. Special Warranty: Manufacturer's standard form, made out to Owner and signed by mirror manufacturer agreeing to replace mirrors that deteriorate, f.o.b. the nearest shipping point to Project site, within specified warranty period indicated in second subparagraph below.

1. Deterioration of Mirrors: Defects developed from normal use that are attributable to the manufacturing process and not to causes other than glass breakage and practices for maintaining and cleaning mirrors contrary to mirror manufacturer's written instructions. Defects include discoloration, black spots, and clouding of the silver film.


PART 2 - PRODUCTS

2.1 SILVERED FLAT GLASS MIRROR MATERIALS

A. Tempered Clear Glass Mirrors: Comply with ASTM C 1503, Mirror Glazing Quality, for blemish requirements in annealed float glass before silver coating is applied, for coating requirements, and with other requirements not affected by tempering process; and comply with ASTM C 1048 for Kind FT, Condition A, tempered float glass before silver coating is applied.

1. Nominal Thickness: 1/4"-inch.

2.2 MISCELLANEOUS MATERIALS

A. Setting Blocks: Elastomeric material with a Type A Shore durometer hardness of 85, plus or minus 5.

B. Edge Sealer: Coating compatible with glass coating and approved by mirror manufacturer for use in protecting against silver deterioration at mirrored glass edges.

C. Mirror Mastic: An adhesive setting compound, produced specifically for setting mirrors and certified by both mirror manufacturer and mastic manufacturer as compatible with glass coating and substrates on which mirrors will be installed.

1. Available Manufacturers: Subject to compliance with requirements, manufacturers offering products that may be incorporated into the Work include, but are not limited to, the following:

2. Manufacturers: Subject to compliance with requirements, provide products by one of the following:

a. Gunther Mirror Mastics. b. Palmer Products Corporation.

3. VOC Content: Not more than 70 g/L when calculated according to 40 CFR 59, Subpart D (EPA Method 24).

2.3 MIRROR HARDWARE

A. Top and Bottom Aluminum J-Channels: Aluminum extrusions with a return deep enough to produce a glazing channel to accommodate mirrors of thickness indicated and in lengths required to cover bottom and top edges of each mirror in a single piece.

1. Bottom Trim: J-channels formed with front leg and back leg not less than 3/8 and 7/8 inch in height, respectively, and a thickness of not less than 0.04 inch.


MIRRORS 088300 3

2. Top Trim: J-channels formed with front leg and back leg not less than 5/8 and 1 inch in height, respectively, and a thickness of not less than 0.04 inch.

3. Available Products: Subject to compliance with requirements, products that may be incorporated into the Work include, but are not limited to, the following:

4. Products: Subject to compliance with requirements, provide one of the following:

a. Bottom Trim:

1) Laurence, C. R. Co., Inc.; CRL Standard "J" Channel. 2) Sommer & Maca Industries, Inc.; Medium Gauge Aluminum Shallow Nose "J"

Moulding Lower Bar. 3) Sommer & Maca Industries, Inc.; Heavy Gauge Aluminum Shallow Nose "J"

Moulding Lower Bar.

b. Top Trim:

1) Laurence, C. R. Co., Inc.; CRL Deep "J" Channel. 2) Sommer & Maca Industries, Inc.; Medium Gauge Aluminum Deep Nose "J"

Moulding Upper Bar. 3) Sommer & Maca Industries, Inc.; Heavy Gauge Aluminum Deep Nose "J"

Moulding Lower Bar.

5. Bottom Trim: J-channels formed with front leg and back leg not less than 5/16 and 3/4 inch in height, respectively.

6. Top Trim: Formed with front leg with a height of 5/16 inch and back leg designed to fit into the pocket created by wall-mounted aluminum cleat.

7. Product: Subject to compliance with requirements, provide the following:

a. Bottom Trim: C. R. Laurence Co., Inc.; D638 FHA Type "J" Channel. b. Top Trim: C. R. Laurence Co., Inc.; D 1638 Top Channel. c. Cleat: C. R. Laurence Co., Inc.; D 1637M Mirror Mount System Cleat.

B. Fasteners: Fabricated of same basic metal and alloy as fastened metal and matching it in finished color and texture where fasteners are exposed.

C. Anchors and Inserts: Provide devices as required for mirror hardware installation. Provide toothed or lead-shield expansion-bolt devices for drilled-in-place anchors. Provide galvanized anchors and inserts for applications on inside face of exterior walls and where indicated.

2.4 FABRICATION

A. Mirror Sizes: To suit Project conditions, cut mirrors to final sizes and shapes.

B. Mirror Edge Treatment: Flat polished edge.

1. Seal edges of mirrors after edge treatment to prevent chemical or atmospheric penetration of glass coating.

2. Require mirror manufacturer to perform edge treatment and sealing in factory immediately after cutting to final sizes.


MIRRORS 088300 4

PART 3 - EXECUTION

3.1 INSTALLATION

A. General: Install mirrors to comply with mirror manufacturer's written instructions and with referenced GANA publications. Mount mirrors accurately in place in a manner that avoids distorting reflected images.

B. Provide a minimum air space of 1/8 inch between back of mirrors and mounting surface for air circulation between back of mirrors and face of mounting surface.

C. For wall-mounted mirrors, install with mastic and mirror hardware.

1. Attach mirror hardware securely to mounting surfaces with mechanical fasteners installed with anchors or inserts as applicable. Install fasteners so heads do not impose point loads on backs of mirrors.

2. For mirror hardware in the form of continuous J-channels at bottom, provide setting blocks 1/8 inch thick by 4 inches long at quarter points. To prevent trapping water, provide, between setting blocks, 2 slotted weeps not less than 1/4 inch wide by 3/8 inch long.

3. For mirror hardware in the form of a continuous J-channel at bottom and continuous top trim at top, fasten J-channel directly to wall and attach top trim to continuous cleat fastened directly to wall.

4. For metal or plastic clips, place a felt or plastic pad between mirror and each clip to prevent spalling of mirror edges.

5. Where indicated, install mirror hardware in the form of J-channels that are fabricated in single lengths to fit and cover top and bottom edges of mirrors.

6. Install mastic as follows:

a. Apply barrier coat to mirror backing where approved in writing by manufacturers of mirrors and backing material.

b. Apply mastic to comply with mastic manufacturer's written instructions for coverage and to allow air circulation between back of mirrors and face of mounting surface.

c. After mastic is applied, align mirrors and press into place while maintaining a minimum air space of 1/8 inch between back of mirrors and mounting surface.

D. Protect mirrors from breakage and contaminating substances resulting from construction operations.

E. Do not permit edges of mirrors to be exposed to standing water.

F. Maintain environmental conditions that will prevent mirrors from being exposed to moisture from condensation or other sources for continuous periods of time.
