Decide which hand is required. Right hand opening illustrated.

Change the hand by turning the door upside down.

Refer To Sheet 10 For Relevant Product Codes

VictoriaPlum.com0344 804 48 48

6mm SLIDING SHOWER DOOR

1

BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION

1) General Information

2) Additional Notes

Please inspect this product upon delivery, any missing parts or manufacturing

defects must be reported immediately to the supplier. Damage or defects reported

later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID

HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.

Glass breakage claims will not be accepted after the product has been unpacked.

Please note: Aluminium is a soft metal, and undergoes a series of extrusion,

fabrication, polishing and anodising processes in order to create your finished

shower enclosure. Some light surface marks are normal, and is a result of the

manufacturing processes. Quality control has ensured that this item is of a good

standard, and is fit for purpose.

Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.

Note: this product is heavy and may require two people to install.

TOOLS REQUIRED

This product is heavy and may require two people to install.

Ø3mm Drill bit

Ø6mm Drill bit

Pencil

Spirit level

Tape measure

DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE

Drill

Flat-headScrewdriver

Cross headScrewdriver

Mallet

Silicone Sealant

PZ1

2

ASSEMBLY INSTRUCTIONS - DRAWING

PACK I.D

E

B

E

E

E

B

B

B

E

PACK I.D

E

C

C

C

DAA

E

BE

EE

(9) 1x Plastic Water Deflector B

(8) 1x Plastic Water Deflector A

(4) 12x Screws 4x12 (6 For Side Panel)

(1) 6x Wall Plugs

(16) 1x Upright Magnet Profile

(2) 2x Wall Profiles

(17) 1x Magnet Seal

(19) 1x Handle(18) 1x Moving Panel

(12) 1x Bottom Profile

(7) 1x Fixed Panel

(5) 18x Screw Cover Clips (6 For Side Panel)

(13) 2x Glass Clips

(20) 2x Top Double Rollers

(6) 6x Screws 4x30

(15) 2x Bottom Double Rollers

(21) 1x Top Profile

(3 18x Screw Cover Caps (6 For Side Panel))

(10) 8x Screws 3.5x30

(14) 2x Screws 4x10

(11) 1x Fixed Panel Bottom Seal

( 1)

( 17)

(9)

(3)

( 19)

( 11)

(5)

(21)

( 13)

(7)

( 15)

(2)

( 18)

( 10)

(4)

(20)

( 12)

(6)

( 14)

(8)

( 16)

NB: ALL MEASUREMENTS + COMPONENT SIZES QUOTED ARE IN MM.

THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.

ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber .

FITTED SLIDING DOOR DRAWING

Installation Steps

3

120030 30

These Instructions show how to install a Sliding Door into a Recess. For Installation into a corner with a Side Panel – refer to the Side Panel Instructions for the relevant installation steps.

THESE INSTRUCTIONS REFER TO FITTING THIS DOOR IN A RECESS. FOR INSTALLATION IN A CORNER, USE THE STEPS SHOWN IN THE SIDE PANEL INSTRUCTIONS.

4

STEP CHECK BOX CONTENTS ARE CORRECT AND THEN MEASURE KEY COMPONENTS.1

STEP 2 DRAWING TO SHOW CORRECT SHOWER TRAY INSTALLATION

WALL

TILE OR WETWALL PANEL

SHOWER TRAY

YES

WALL

TILE OR WETWALL PANEL

SHOWER TRAY

NO

STEP 3 TRAY TO BE LEVEL

MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THISSHOWER PANEL / DOOR, AND THAT SILICONE IS APPLIED ON ALL SIDES WHERE THETRAY MEETS THE TILES / WET WALL PANELS.

Measurement Matrix (before assembly) Dimension in mm

Units supplied loose for self assembly

Top / Bottom horizontal profiles

Moving panel glass

Wall profiles

Upright magnet profile

SDB120

Flat fixed panel glass(including fixed panel profiles if attached)

1048

568x1834x6

514x1780x6

1850x44

1850x46

STEP 4 ASSEMBLE FRAME AND FIXED PANEL

STEP 5 MARK WALL FIXING POSITIONS OF FIXED PANEL SIDE, DRILL WALL PROFILE OF FIXED

5

Take Care Not To Damage Wall Surface

x31

6mm

x32

x33

M4X30

x34

M4X10

M4X10

M3.5X30

M3.5X30 M3.5X30

PANEL SIDE TO THE WALL

M3.5X30

STEP 6 SLIDE WALL PROFILE OF MOVING PANEL SIDE ONTO THE FRAME

STEP 7 LIFT THE FRAME ONTO THE TRAY AND MARK WALL PROFILE POSITIONS OF

6

MOVING PANEL SIDE

STEP 8 LIFT THE FRAME OFF THE TRAY AND DRILL THE WALL

STEP 9 FITTING THE WALL PROFILE

7

6mm

x3

Take Care Not To Damage Wall Surface

Adjust the door so to be centralbetween the wall profiles .

View from outside

View from inside

M4X30x3

x3

x3

STEP 10 SECURING THE VERTICAL PROFILES

STEP 11 FITTING THE TOP AND BOTTOM ROLLERS TO THE MOVING PANEL, AND ATTACHING

8

How to adjust the width of the

sliding door

Minimum 10mm internal overlap required

Glass panel

Glass panel

Vertical profile

Vertical profile

Wall profile

Wall profile

Wall

Wall

Maximum adjustment

Minimum adjustment

Take care not to drill into the glass.

x63mm1

x6M4X122

x63

1 x23 x2 2 x2

Use a spirit level to make sure the door is square within the frame.

THE MOVING PANEL TO THE FRAME

1 x2

2 x2

3 x2

STEP 12 INSTALLING VERTICAL SEALS, AND FITTING HANDLE

STEP 13 SILICONE THE OUTSIDE EDGES

9

Silicone ( outside edge only)where the

horizontal profile meets the tray

vertical profiles meet the wall , and the

CARE AND MAINTENANCE

COMMITMENT TO QUALITY

1) AFTER CARE INSTRUCTIONS

2) MAINTENANCE

Regularly clean your shower product with warm soapy water

Clean the plastic parts with a cloth and mild detergent. Never

use any abrasive creams, dissolvents, acetone or detergents

and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained

in these instructions. The supplier reserves the right to introduce

technical changes without notice.

It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you

firstly contact a competent plumber. However we understand that

this may not always be the case, so should you experience

any problems please contact our customer services quoting

the following:

to prevent lime scale build up. Do not use abrasive cleaning

fluids or materials, or strong chemical cleaners as this will

damage the product surface.

Product name: 6mm Sliding Shower Door

Product code: SDB120

Customer help line number:0344 804 48 48

10

The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.

We suggest you take it to the local landfill site and discard in the designated bins.

V05/09/2019

Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG

Park

13/14/16

EN 14428:2004+A1:2008

DOP No.:2013102/2014612/J160318001-1

Shower enclosures with aluminiumprofiles and safety glass

Essentialcharacteristics

Performance Harmonisedtechnical

specificationCleanability

Impactresistance/shatter

properties

Pass

Pass

PassDurability

Clause 4.2 of EN14428:2004+A1:

2008Clause 4.3 of EN14428:2004+A1:

2008Clause 4.4 of EN14428:2004+A1:

2008