SDAccel Development Environment - Xilinx...This guide describes how to obtain a license, install the SDAccel development environment, and install the supported FPGA acceleration cards

SDAccel Development Environment

Installation and Licensing Guide

UG1020 (v2015.4) February 16, 2016

SDAccel Installation and Licensing Guide www.xilinx.com 2UG1020 (v2015.4) February 16, 2016

Revision HistoryThe following table shows the revision history for this document.

Date Version Revision

02/16/2016 2015.4 Added board and driver installation instructions.

10/22/2015 2015.3 Re-release, no technical changes.

06/29/2015 2015.1.2 Updated target platform example on page 11.

05/26/2015 2015.1 Initial Xilinx Release.

Send Feedback

http://www.xilinx.com

http://www.xilinx.com/about/feedback.html?docType=User_Guides&docId=UG1020&Title=SDAccel%20Development%20Environment%20User%20Guide%3A%20Installation%20and%20Licensing&releaseVersion=2015.4&docPage=2


Table of ContentsRevision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1: IntroductionOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Software Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Chapter 2: Obtaining a LicenseObtaining a License for SDAccel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Chapter 3: Software InstallationDownload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 4: Board InstallationsInstalling the Alpha Data ADM-PCIE-KU3 Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Installing the Alpha Data ADM-PCIE-7V3 Card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Chapter 5: Verifying Installation

Appendix A: xbinst Command Reference

Appendix B: Additional Resources and Legal NoticesXilinx Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Solution Centers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37Please Read: Important Legal Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Send Feedback



Chapter 1

Introduction

OverviewSDAccel™ is a development environment for OpenCL™ applications targeting Xilinx® FPGA based accelerator cards. This environment enables concurrent programming of the in-system processor and the FPGA fabric without the need for RTL design experience. The application is captured as a host program written in C/C++ and a set of computation kernels expressed in C, C++, or the OpenCL C language.

This guide describes how to obtain a license, install the SDAccel development environment, and install the supported FPGA acceleration cards.

Hardware Requirements• Acceleration Card. Use one of the following:

° Alpha Data ADM-PCIE-KU3 card. The card is based on the Kintex® UltraScale XCKU060T-2FFVA1156E FPGA.

° Alpha Data ADM-PCIE-7V3 card. The card is based on the Virtex®-7 XC7VX690T-2FFG1157C FPGA.

• Host computer: Desktop computer for hosting the acceleration card. The host computer must provide:

° Motherboard with a PCIe Gen3 X8 slot

° 16 GB RAM

° 100GB free disk space

° DVD drive

• Programming computer: Laptop or desktop computer running Vivado Design Suite 2015.4 for programing the FPGA.

• Xilinx® Platform Cable USB 2, part number HW-USB-II-G for connecting the programming computer to the acceleration card (see Platform Cable USB II (DS593)


Send Feedback



Chapter 1: Introduction

Software Requirements• Vivado Lab Edition 2015.4 for programming the FPGA device on the programming

computer.

• RedHat Enterprise Linux or CentOS 6.4-6.7 64-bit

• The following packages must be installed on the host machine.

° $sudo yum install gcc

° $sudo yum install kernel-devel


Send Feedback



Chapter 2

Obtaining a License

Obtaining a License for SDAccelThe steps to obtain a license for the SDAccel™ development environment are:

1. Sign in to the Xilinx® licensing website: www.xilinx.com/getproduct (see Figure 2-1).

You need a valid account for www.xilinx.com to sign in and generate licenses. If this is your first time generating a license for SDAccel - Xilinx OpenCL Design Environment, contact your Xilinx representative to enable your access to the SDAccel licensing website.

2. Select XILINX - SDACCEL in the account drop-down menu, as shown in Figure 2-2.

X-Ref Target - Figure 2-1

Figure 2-1: Sign in Screen


Figure 2-2: Account Selection Screen


Send Feedback



http://www.xilinx.com/getproduct


Chapter 2: Obtaining a License

3. Select SDAccel Development Environment, Node-Locked License from the Certificate Based Licenses menu:

4. Click Generate node-locked license.

5. Enter a Host ID in the License Generation screen and click Next.

6. Verify that the Host ID for the license is correct and click Next.

7. Accept the licensing agreement by clicking Accept.

8. You will receive an email from [email protected] with the license file.

9. Set the XILINXD_LICENSE_FILE environment variable to point to the location of the license file on your system.


Figure 2-3: Certificate Based Licenses Menu


Send Feedback



Chapter 3

Software Installation

Download1. Log into www.xilinx.com/getproduct.

2. In the account drop-down menu, select XILINX – SDACCEL.

3. Click the Restricted Downloads tab to gain access to the SDAccel™ installation package as shown in Figure 3-1.


Figure 3-1: Restricted Downloads Tab


Send Feedback


http://www.xilinx.com/getproduct


Chapter 3: Software Installation

Installation1. To start the installation process, execute xsetup inside the top-level directory for the

SDAccel installer package.

IMPORTANT: Superuser privileges may be required to install the software on a system-level directory.

This command starts the installation of SDAccel and displays the welcome screen shown in Figure 3-2.

2. Click Next.


Figure 3-2: SDAccel Installer Welcome Screen


Send Feedback




3. Select I agree to agree to the license terms of the software and click Next (see Figure 3-3).


Figure 3-3: License Terms and Conditions


Send Feedback




4. Select installation options. SDAccel is a self-contained software tool suite and installs all of the necessary tools. The only choice on this menu is whether to get a new license for the software or reuse an existing license. Click Next.

5. Select the installation directory for the software, as shown in Figure 3-4.

The installation directory name must not contain any spaces in any part of the directory path. SDAccel requires 18 GB of free space for the installation to complete.

6. Review the Installation Summary page and click Install.The installation process will take several minutes to complete.

7. To set up the environment to run SDAccel, source the file below so that sdaccel command is in the PATH:

C Shell: source <SDACELL_INSTALL_DIR>/settings64.cshBash: source <SDACELL_INSTALL_DIR>/settings64.sh


Figure 3-4: Select Installation Directory Screen


Send Feedback



Chapter 4

Board InstallationsFollow the installation instructions appropriate for your the acceleration card:

• Installing the Alpha Data ADM-PCIE-KU3 Card

• Installing the Alpha Data ADM-PCIE-7V3 Card

Installing the Alpha Data ADM-PCIE-KU3 CardThe ADM-PCIE-KU3 card is a high-performance reconfigurable computing card for data center applications. It features:

• Kintex® UltraScale™ XCKU060T-2FFVA1156E FPGA

• 16 GB of DDR3 memory

Step 1: Prepare Board Installation Files1. SDAccel™ provides a utility, xbinst, that generates firmware and driver files for the

target board plugged into the host computer. Run the commands below to prepare files for ADM-PCIE-KU3 card installation. See Appendix A, xbinst Command Reference for more details on the xbinst utility.


Figure 4-1: ADM-PCIE-KU3/KU060E card


Send Feedback



Chapter 4: Board Installations

Note: All commands must be run with root or sudo privilege.

$sudo mkdir ku3_dsa$ sudo xbinst -x xilinx:adm-pcie-ku3:1ddr:2.1 -d ku3_dsa****** xbinst v2015.4 **** Copyright 1986-2016 Xilinx, Inc. All Rights Reserved.INFO: [XBINST 60-267] Packaging for PCIe...INFO: [XBINST 60-268] Packaging for PCIe...COMPLETEINFO: [XBINST 60-667] xbinst has successfully created a board installation directory at /opt/dsa/ku3_dsa

Make a note of the board installation directory. This procedure uses /opt/dsa/ku3_dsa as an example in this chapter.

Copy the following file path to the programming computer:

/opt/dsa/ku3_dsa/xbinst/pkg/pcie/firmware/xilinx_adm-pcie-ku3_1ddr_2_1.mcs

Make a note of the file location on the programming computer as it will be required for programming the configuration memory in a later step.

Step 2: Setting up the Card and Computer1. Make sure the host computer is completely turned off.

2. Locate DIP switch SW1 on the back side of the board near the center of top edge and set it as shown here:

3. Install the ADM-PCIE-KU3 card into an open PCIe slot in the host computer.

IMPORTANT: Follow host computer manufacturer recommendations to ensure proper mounting and adequate cooling.

4. Turn on the host computer.


Figure 4-2: DIP Switch SW1

23

41

On

Off

Pin 1


Send Feedback




Step 3: Programming the Base PlatformAll applications compiled by the SDAccel™ compiler for the Alpha Data card are compiled against a specific device. A device is a combination of interfaces and infrastructure components on the card, which are required for proper execution of the user program. The base device program or firmware is different for all devices. This program must be loaded onto the FPGA before the user application is loaded. To program the firmware program:

1. Connect the Alpha Data ADM-PCIE-KU3 card to the programming computer with an installation of Vivado® Design Suite as shown here:

2. On the programming computer, start the Vivado Design Suite then on the Welcome page, select Open Hardware Manager.


Figure 4-3: Programming Connections


Figure 4-4: Open Hardware Manager Icon

Wally


Send Feedback




3. Select Open a New Hardware Target.

4. Click Next in the Open Hardware Target window.


Figure 4-5: Open a New Hardware Target


Figure 4-6: Open New Hardware Target Window


Send Feedback




5. Select Local server in the Connect to field and click Next.X-Ref Target - Figure 4-7

Figure 4-7: Hardware Server Settings


Send Feedback




6. In the Open New Hardware Target window, select xilinx_tcf and click Next.X-Ref Target - Figure 4-8

Figure 4-8: Select Hardware Target


Send Feedback




7. In the Open Hardware Target Summary window, click Finish.

8. Right-click your FPGA (xku060_0), and select Add Configuration Memory Device.


Figure 4-9: Open Hardware Target Summary


Figure 4-10: Add Configuration Memory Device


Send Feedback




9. Select mt28gu01gaax1e-bpi-x16 as the configuration memory.

10. Click OK to program the configuration memory.

11. In the Programming Configuration Memory Device window (Figure 4-13), go to the Configuration File entry box, browse to and select the MCS file (xilinx_adm-pcie-ku3_1ddr_2_1.mcs) that you copied to the programming


Figure 4-11: Select Configuration Memory


Figure 4-12: Program Configuration Memory


Send Feedback




computer in Step 1. Verify all other settings as shown in the Program Configuration Memory Device window. Click OK to start programming the configuration memory.


Figure 4-13: Program Configuration Memory Device Window


Send Feedback




12. After the memory has been configured, right-click the FPGA (xku060_0) and select Boot From Configuration Device.

The Tcl console displays Done pin status: HIGH after the FPGA device is booted successfully.

13. Reboot the host computer.

IMPORTANT: Programming of the device firmware is required only once per device support archive (dsa). All applications targeting the same dsa can share a single programming instance of the card firmware.

Step 4: Installing Driver for the CardYou must install proper drivers for the card before you can use it to run SDAccel applications. Follow the instructions below to install the required drivers.

Change to the board installation directory generated in Step 1 and run installation script:


Figure 4-14: Boot from Configuration Memory Device


Figure 4-15: Done Pin Status


Send Feedback




$cd /opt/dsa/ku3_dsa/xbinst/pkg/pcie$sudo ./install.sh

This will do the following.

• Compile and install Linux kernel device drivers.

• Install the firmware to the Linux firmware area.

• Generate a setup.sh (Bash) or setup.csh (for csh/tcsh) to set up the runtime environment. You must source the setup script before running any application on the target FPGA card.

• Install Xilinx OpenCL Installable Client Driver (ICD) to /etc/OpenCL/vendors. The OpenCL ICD) allows multiple implementations of OpenCL to co-exist on the same system. It allows applications to choose a platform from the list of installed platforms and dispatches OpenCL API calls to the underlying implementation.

Step 5: Verify Board InstallationAfter you reboot the host machine, run the command below to confirm that ADM-PCIE-KU3 card is successfully enumerated on the host machine. Take note of the PCIe bus number (03:00.0 in this case)

$sudo lspci | grep Xilinx03:00.0 Memory controller: Xilinx Corporation Device 8138

Run the lspci command on the PCIe bus number from previous step to get more details and confirm that the vendor ID, subsystem ID, link speed, and kernel driver/module of the card match the output below:

$sudo lspci -s :03:00.0 -vv03:00.0 Memory controller: Xilinx Corporation Device 8138Subsystem: Xilinx Corporation Device 0121

……

LnkSta:Speed 8GT/s, Width x8…

…Kernel driver in use: xcldmaKernel modules: xcldma


Send Feedback




Installing the Alpha Data ADM-PCIE-7V3 CardThe ADM-PCIE-7V3 card is a high-performance reconfigurable computing card for data center applications. It features:

• A Virtex®-7 XC7VX690T-2FFG1157C FPGA

• 16 GB of DDR3 memory

Step 1: Prepare Board Installation Files1. SDAccel provides a utility. xbinst. that generates firmware and driver files for the

target board plugged into the host computer. Run the commands below to prepare files for ADM-PCIE-KU3 card installation. See Appendix A, xbinst Command Reference for more details on xbinst utility.

Note: All commands need to be run with root or sudo privilege.

$sudo mkdir 7v3_dsa$ sudo xbinst -x xilinx:adm-pcie-7v3:1ddr:2.1 -d 7v3_dsa****** xbinst v2015.4 **** Copyright 1986-2016 Xilinx, Inc. All Rights Reserved.INFO: [XBINST 60-267] Packaging for PCIe...INFO: [XBINST 60-268] Packaging for PCIe...COMPLETEINFO: [XBINST 60-667] xbinst has successfully created a board installation directory at /opt/dsa/7v3_dsa

Make a note of the board installation directory. This procedure uses /opt/dsa/7v3_dsa in this chapter.


Figure 4-16: ADM-PCIE-7V3 card


Send Feedback




Copy the following file path to the programming computer:

/opt/dsa/7v3_dsa/xbinst/pkg/pcie/firmware/xilinx_adm-pcie-7v3_1ddr_2_1.mcs

Make a note the file location on the programming computer as it will be required for programming the configuration memory in later step.

Step 2. Setting Up the Card and Computer1. Make sure the host computer is completely turned off.

2. Locate DIP switch SW1 on the back side of the board near the center of top edge and set

it as shown here:

3. Install the ADM-PCIE-7V3 card into an open PCIe slot in the host computer.

IMPORTANT: Follow host computer manufacturer recommendations to ensure proper mounting and adequate cooling.

4. Turn on the host computer.

Step 3: Programming the Base PlatformAll applications compiled by the SDAccel™ compiler for the Alpha Data card are compiled against a specific device. A device is a combination of interfaces and infrastructure components on the card, which are required for proper execution of the user program. The base device program or firmware is different for all devices. This program must be loaded onto the FPGA before the user application is loaded. To program the firmware program:


Figure 4-17: DIP Switch SW1

2 3 41

On

Off

Pin

1


Send Feedback




1. Connect the Alpha Data ADM-PCIE-7V3 card to the control computer having an installation of Vivado® Design Suite as shown here:

2. On the programming computer, Open Hardware Manager.

3. Select Open a New Hardware Target.


Figure 4-18: Programming Connections


Figure 4-19: Open Hardware Manager Icon


Figure 4-20: Open a New Hardware Target Link

Wally


Send Feedback




4. 4. Click Next in the Open Hardware Target window.X-Ref Target - Figure 4-21

Figure 4-21: Open New Hardware Target Window


Send Feedback




5. 5. Select Local server in the Connect to field and click Next.X-Ref Target - Figure 4-22

Figure 4-22: Hardware Server Settings


Send Feedback




6. In the Open New Hardware Target window, select xilinx_tcf and click Next.X-Ref Target - Figure 4-23

Figure 4-23: Select Hardware Target


Send Feedback




7. In the Open Hardware Target Summary window, click Finish.

8. Right-click the FPGA (xc7vx690T_0) and select Add Configuration Memory Device.


Figure 4-24: Open Hardware Target Summary


Figure 4-25: Add Configuration Memory Device


Send Feedback




9. Select mt28gu01gaax1e-bpi-x16 as the configuration memory.

10. Click OK to program the configuration memory.

11. In the Programming Configuration Memory Device window (Figure 4-28), go to the Configuration File entry box, browse to, and select the MCS file (xilinx_adm-pcie-7v3_1ddr_2_1.mcs) that you copied to the programming


Figure 4-26: Select Configuration Memory


Figure 4-27: Program Configuration Memory


Send Feedback




computer in Step 1. Verify all other settings as shown in the Program Configuration Memory Device window. Click OK to start programming the configuration memory.

12. After the memory has been configured, right-click the FPGA (xc7vx690T_0) and selectBoot From Configuration Device.


Figure 4-28: Program Configuration Window


Figure 4-29: Boot from Configuration Memory


Send Feedback




The Tcl console displays Done pin status: HIGH after the FPGA is booted successfully.

13. Reboot the host computer.

IMPORTANT: Programming of the device firmware is required only once per device. All applications targeting the same device can share a single programming instance of the card firmware.

Step 4: Installing Driver for the CardYou must install proper drivers for the card before you can use it to run SDAccel applications. Follow the instructions below to install the required drivers.

Change to the board installation directory generated in Step 1, and run installation script:

$cd /opt/dsa/7v3_dsa/xbinst/pkg/pcie$ sudo ./install.sh

This will do the following:


• Install the firmware to the Linux firmware area.

• Generate a setup.sh (Bash) or setup.csh (for csh/tcsh) to set up the runtime environment. Users must source the setup script before running any application on the target FPGA card.

• Install Xilinx OpenCL Installable Client Driver (ICD) to /etc/OpenCL/vendors. The OpenCL ICD) allows multiple implementations of OpenCL to co-exist on the same system. It allows applications to choose a platform from the list of installed platforms and dispatches OpenCL API calls to the underlying implementation.


Figure 4-30: Done Pin Status


Send Feedback




Step 5: Verify Board InstallationAfter you reboot the host machine, run the command below to confirm that ADM-PCIE-7V3 card is successfully enumerated on the host machine. Take a note of the PCIe bus number (03:00.0 in this case)


Run lspci command on the PCIe bus number from previous step to get more details and confirm that the vendor ID, subsystem ID, link speed, and kernel driver/module of the card match the output below:


$sudo lspci -s :03:00.0 -vv03:00.0 Memory controller: Xilinx Corporation Device 7138Subsystem: Xilinx Corporation Device 0121

……

LnkSta:Speed 8GT/s, Width x8…

…Kernel driver in use: xcldmaKernel modules: xcldma


Send Feedback




Chapter 5

Verifying InstallationAfter completing the installation process, verify that the tool was correctly installed by following the steps in the SDAccel Development Environment Tutorial, (UG1021) [Ref 1].

Contact your Xilinx representative if you can not properly complete the steps in the tutorial.

Send Feedback



Appendix A

xbinst Command ReferenceThe FPGA acceleration card plugged into the host machine needs to have the associated Linux kernel driver, firmware and runtime libraries installed before it can be used for running user applications. SDAccel provides a Xilinx board installation utility, xbinst to generate all necessary files for the device support archive (DSA) for the FPGA card. It also generates an installation script to compile and install the driver, firmware and runtime libraries.

The xbinst utility requires superuser privileges on the host machine to run. The supported options are listed below:

Follow the instructions below to install the driver and firmware for the FPGA card on the host machine. The ADM-PCIE-7V3 DSA is used as an example. Replace it with the DSA for the actual card plugged into the system.

Table A-1: xbinst Options

Short Option Long Option Valid Values Description

-h --help NA Print Usage Message

-x <arg> --dsa <arg> Supported acceleration devices by Xilinx and third-party board partners.

Required.

The following devices are installed withthe SDAccel environment:xilinx:adm-pcie-7v3:1ddr:2.1ADM-PCIE-7V3 card with one DDR3 interface

xilinx:adm-pcie-ku3:1ddr:2.1ADM-PCIE-KU3 card with one DDR3 interface

xilinx:adm-pcie-ku3:2ddr:2.1ADM-PCIE-KU3 card with two DDR3 interfaces

-d <arg> --destination <arg>

Valid path on the file system.

Required destination directory for driver and firmware for the specified DSA

-i <arg> --dsadir <arg> Valid path on the file system with user DSA files.

Specify the search path for user DSAs that are not installed with SDAccel. e.g. a DSA from an SDAccel board partner.


Send Feedback



Appendix A: xbinst Command Reference

Note: All commands need to be run with superuser privileges.

1. Create a board installation directory

$sudo mkdir 7v3_dsa_v21

2. Run xbinst to generate all necessary files

$ sudo xbinst -x xilinx:adm-pcie-7v3:1ddr:2.0 -d 7v3_dsa_v21****** xbinst v2015.4 **** Copyright 1986-2016 Xilinx, Inc. All Rights Reserved.INFO: [XBINST 60-267] Packaging for PCIe...INFO: [XBINST 60-268] Packaging for PCIe...COMPLETEINFO: [XBINST 60-667] xbinst has successfully created a board installation directory at /opt/dsa/7v3_dsa_v21

3. Install the driver, firmware, and runtime libraries

$cd 7v3_dsa_v21/xbinst/pkg/pcie/$ sudo ./install.sh

This will do the following:


• Install the firmware files to the Linux firmware area.

• Generate a setup.sh (Bash) or setup.csh (for csh/tcsh) to set up the runtimeenvironment. Users must source the setup script before running any application on thetarget FPGA card.


Send Feedback




Appendix B

Additional Resources and Legal Notices

Xilinx ResourcesFor support resources such as Answers, Documentation, Downloads, and Forums, see Xilinx Support.

Solution CentersSee the Xilinx Solution Centers for support on devices, software tools, and intellectual property at all stages of the design cycle. Topics include design assistance, advisories, and troubleshooting tips.

References1. SDAccel Development Environment Tutorial (UG1021).

Please Read: Important Legal NoticesThe information disclosed to you hereunder (the “Materials”) is provided solely for the selection and use of Xilinx products. To the maximum extent permitted by applicable law: (1) Materials are made available "AS IS" and with all faults, Xilinx hereby DISCLAIMS ALL WARRANTIES AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and (2) Xilinx shall not be liable (whether in contract or tort, including negligence, or under any other theory of liability) for any loss or damage of any kind or nature related to, arising under, or in connection with, the Materials (including your use of the Materials), including for any direct, indirect, special, incidental, or consequential loss or damage (including loss of data, profits, goodwill, or any type of loss or damage suffered as a result of any action brought by a third party) even if such damage or loss was reasonably foreseeable or Xilinx had been advised of the possibility of the same. Xilinx assumes no obligation to correct any errors contained in the Materials or to notify you of updates to the Materials or to product specifications. You may not reproduce, modify, distribute, or publicly display the Materials without prior written consent. Certain products are subject to the terms and conditions of Xilinx’s limited warranty, please refer to Xilinx’s Terms of Sale which can be viewed at http://www.xilinx.com/legal.htm#tos; IP cores may be subject to warranty and support terms contained in a license issued to you by Xilinx. Xilinx products are not designed or intended to be fail-safe or for use in any application requiring fail-safe performance; you assume sole risk and liability for use of Xilinx products in such critical applications, please refer to Xilinx’s Terms of Sale which can be viewed at http://www.xilinx.com/legal.htm#tos.© Copyright 2012-2016 Xilinx, Inc. Xilinx, the Xilinx logo, Artix, ISE, Kintex, Spartan, Virtex, Vivado, Zynq, and other designated brands included herein are trademarks of Xilinx in the United States and other countries. OpenCL and the OpenCL logo are trademarks of Apple Inc. used by permission by Khronos. All other trademarks are the property of their respective owners

Send Feedback


http://www.xilinx.com/support/solcenters.htm

http://www.xilinx.com/support

http://www.xilinx.com/support

http://www.xilinx.com/legal.htm#tos

http://www.xilinx.com/legal.htm#tos

http://www.xilinx.com/cgi-bin/docs/rdoc?v=2015.4;d=ug1021-sdaccel-tutorial.pdf


Documents

SDAccel Development Environment - Xilinx...This guide describes how to obtain a license, install the SDAccel development environment, and install the supported FPGA acceleration cards