Dual SD Card Mobile DVR

MANUAL

Catalogue

1 Product Specification........................................................................................... - 2 -

2 Product Applications ........................................................................................... - 4 -

3 Appearance of Product........................................................................................ - 6 -

3.1 Device Appearance ................................................................................................ - 6 - 3.2 Device Drawing Dimension & Install Holes ............................................................ - 7 - 3.3 Front & Back Panel led & Plug-in module. ............................................................. - 7 - 3.4 Back Panel Interface Definition .............................................................................. - 8 - 3.5 Power Cable ........................................................................................................... - 9 - 3.6 GPS Antenna........................................................................................................ - 10 - 3.7 Alarm input and output ......................................................................................... - 10 - 3.8 Device Installation Guide...................................................................................... - 11 -

4 Remote control function keys instruction ....................................................... - 12 -

5 Device Functions and Operation Guide........................................................... - 13 -

5.1 Login Menu........................................................................................................... - 16 - 5.2 System Settings.................................................................................................... - 16 -

5.2.1 Basic Settings................................................................................. - 17 - 5.2.2 Power off/on Setting ....................................................................... - 18 - 5.2.3 Network Setting .............................................................................. - 18 - 5.2.4 Password Setting............................................................................ - 19 -

5.3 Record Setting...................................................................................................... - 20 - 5.3.1 General Setting............................................................................... - 20 - 5.3.2 Channel Setting .............................................................................. - 21 - 5.3.3 Record Schedule Menu .................................................................. - 22 - 5.3.4 Sub-Stream Setting ........................................................................ - 23 -

5.4 Vehicle Info ........................................................................................................... - 23 - 5.4.1 Sensor Setting ................................................................................ - 24 - 5.4.2 Speed ............................................................................................. - 24 - 5.4.3 Accelerate ...................................................................................... - 25 -

5.5 Management Tool ................................................................................................. - 25 - 5.5.1 Format ............................................................................................ - 26 - 5.5.2 Configuration Management ............................................................ - 27 - 5.5.3 Upgrade.......................................................................................... - 27 - 5.5.4 Log Management............................................................................ - 28 - 5.5.5 Motion Detection............................................................................. - 28 -

5.6 Play back .............................................................................................................. - 30 - 5.7 Quick setup........................................................................................................... - 30 - 5.8 Module Management............................................................................................ - 30 -

5.8.1 Wireless Setup ............................................................................... - 31 - 5.8.2 WIFI Setup...................................................................................... - 32 - 5.8.3 PTZ setup....................................................................................... - 33 -

5.9 System Information............................................................................................... - 36 -

- 1 -

1 Product Specification

The MDVR (Automotive) is a cost-effective, functional and scalable device designed for video surveillance and remote monitoring of your mobile assets. It uses a high-speed processor, an embedded Linux platform and combines the most advanced IT processes such as H.264 Video Compression/Decompression, networking and GPS positioning technology. MDVR enables CIF, HD1 and D1 video formats. Drivers' driving information, recording and wireless data are uploaded to SD Memory Cards which are used as the storage medium. A MDVR centric software platform (CMS) can be realized with links to a Central Alarm monitoring system for remote management and playback analysis. The MDVR may look simple in its exterior design, provides powerful auto black box features, installation flexibility and high reliability. MDVR Specifications

Items Parameters Specifications

Language Chinese/English

Operation Menu Graphical User interface OSD menu

System

Password Users Password/ Administrator Password

Video input 4-CH video input 1.0Vp-p 75Ω

Video output 1-CH video COMPOSITE output 1.0Vp-p 75Ω

Video Display 1 channel or synchronous 4 channels

Video Signal PAL NTSC

Video

Video Compression

H.264 Main profile 75fps D1/s

Audio input 4-ch Audio input

Audio output 1-ch Audio output Audio

Recording mode Audio & Video sync Recording

Video format CIF/HD1/D1 Optional

Video stream Standard

ISO14496-10

Image processing &

storage

Video bit rate

CIF: 1536Kbps - 128Kbps 8 levels optional.Highest:1 level

HD1: 2048Kbps - 380Kbps 8 levels optional.Highest:1 level

D1: 2048Kbps - 400Kbps 8 levels optional.Highest:1 level

- 2 -

Audio Bitrate 8KB/s

Storage Support Dual SD card storage, 64GB for each.

Alarm input 6 alarm inputbelow 4V is low level alarm 4V，above 4V are up level alarm Alarm

Alarm output 2 alarm output，output up level:12V

RS485 Interface Support 2-RS485 interface

RS232 Interface Support 1-RS232 interface Communicatio

n Interface WIFI Interface Support 802.11b/g

Auto Station

reporter Interface

Support connecting Auto Station Reporter or control panel via extended interface

Extended interface Audio power

amplifier Support 2-ch audio power amplifier output

CDMA CDMA module Optional

GPRS/EDGE GPRS / EDGE module Optional Wireless Transmission 3G(HSDPA/EVDO

) 3G(HSDPA / EVDO / WCDMA)module Optional

GPS Built-in GPS module Geographic co-ordinates speed can be read in coding flow and can be uploaded via wireless

Acceleration Sensor

Built in acceleration G-Sensor

Analysis of PC playback

Playback Recording on PC and analyse the vehicle recording info

Software CMS

Via Wifi, to meet Video preview GPS upload alarm upload, central command and parameters configuration, etc

Software Upgrade

SD cards upgrade

MDVR Electric Specifications

Items Parameters Specifications

Power input 8-36V 8V-36V, When long-term under 8V, or long-term over

36V, Auto power off, enter protected mode

Power output 12V 12V (+/-0.2V) Max:2A.

Vehicle key ≤4V OFF

- 3 -

signal ≥5V ON

Video input

impedance 75Ω 75Ω for each video input impedance

Video output

Volt 2Vp-p

Input 2Vp-p CVBS analog signal, reveal device input

need 75Ω impedance to fit

0-4V Low level alarm

I/O interface More than

4V High level alarm

SD-card

interface 2 SD card

1.32GB for each card.

2.SD-card for storage, support recording and system

upgrade, etc.

Operating

Temp -40-80 Under well-ventilated environment

2 Product Applications

- 4 -

- 5 -

3 Appearance of Product

3.1 Device Appearance

MDVR Device Appearance

- 6 -

3.2 Device Drawing Dimension & Install Holes

3.3 Front & Back Panel led & Plug-in module.

1.1 Front & Back Panel led & Plug-in module.

Front Panel definition as below:

Interface Items Description

VIDEO-OUT VIDEO-OUT Video Simulation output

- 7 -

SD1 SD1 card recording led, light on as SD1

exist.

SD2 SD1 card recording led, light on as SD2

exist.

REC Recording led，light on as recording

GPS GPS signal led，light on as GPS module

exist.

POWER Led, Light on as power normal

ALM ALM LED, light on as device abnormal

CAM1/CAM2/CAM3/CAM4Light on as CAM1/CAM2/CAM3/CAM4

has signal, or else, no light on

WIFI Light on as WIFI module exist

LED

2G/3G Light on as 2G/3G module exist

IR

receiver IR IR receiver, receive remote control signal

Electronic Lock

LOCK During working, open key lock, system will load-off 2-SD cards, load-on recording after

1min auto.

3.4 Back Panel Interface Definition

Pic 8 Back Panel interface definition

Back Panel interface definition as followed: Pic 8 Back Panel interface definition

- 8 -

Interface Items Description

WIFI interface WIFI Wireless LAN antenna interface

GPS interface GPS GPS antenna interface

2G/3G interface 2G/3G 2G/3G antenna interface

Power input interface DC8-36V Power input interface

LPT MCU System adjust info interface

Extended interface EXTENTION Control panel interface

Video output interface VIDEO- OUT Video output

Audio output interface AUDIO- OUT Audio output

CAN-BUS interface CAN-BUS Vehicle electronic control network

Sensors interface SENSORS Swich input interface，high level（>4V）

Vehicle speed pulse input interface

SPEED Input vehicle speed pulse signal, differential input

RS485/RS232 interface

RS485/RS232 RS232 / RS485 serial data communication interface

Speaker interface SPEAKER Audio power amplifier output

3.5 Power Cable

Figure 8 shows the power cable, one end is 6Pin with White Plug, connected to the device panel 6Pin White Connector. The Red and Black wire is connected directed to the vehicle's battery. Red wire is POSITIVE and Black is NEGATIVE. Yellow cable is FIREWIRE. The device which be turned on when the vehicle's key are in the ignition and turns off or delay turn off when the keys are taken out. The yellow cable connects the point of panel lamp key opened (point of vehicle ignition).

NOTES：

1）Please verify battery voltage before connecting. Voltage accepted is between 12V-36V. A higher voltage will damage the device.

2）After connecting the cables, ensure that power cables are insulated to prevent short circuiting

and burning out the battery.

3）The Yellow cable must be connected to the vehicle ignition cable, otherwise the device will not be able to execute the delayed shutdown and the final moment of the video will be lost.

- 9 -

4）Note: Connection to the vehicle's engine must be connected directly to the positive anode of the battery. Do Not Use bond strap for grounding as it will produce negative pulses that would interfere the device's normal operation. The negative pole of the power code must be Φ1.5mm and above.

PIC10 Power Supply Diagram

3.6 GPS Antenna

GPS Antenna

3.7 Alarm input and outpu

The device has 6 alarm input and 2 alarm

be detected while the vehicle is in motion. Ac

diagram that shows when the braking vane Is

high level, otherwise, just detect the low level.

t

output interfaces. Various state of alarm level can

tion`s such as braking, steering horn etc. Below is a

depressed, the MDVR would be able to detect the

- 10 -

Stoplight +24V

Braking vane

Connect MDVR sensor input cable

Alarm outputs are level output drive capability for the 200MA, if you want to drive relatively

large power device, must connect external relay. Shown below is the Alarm output photoelectric

alarm wiring diagram.

2MDVR ALM output 4V

3.8 Device Installation Guide

A Inspecting the Accessories

After unpacking, please check the device for damage or deformation. If there are, please do

not install the device and get in touch with the supplier. In the product box there is a packing list.

Please cross check this list with the device and its accompanying accessories.

B Installing the SD and SIM Card

SD cards are on the main board, insert SD1 & SD2 from the front board of device. SIM card is on the communication board, take down the small shield of the device. You can see SIM interface. Insert it into clip (Negative up). When system supports 3G, then there is a need to install SIM card.

- 11 -

4 Remote control function keys instruction

There is no control button on MDVR panel, need remote control to fit operating Key-press & function as below: Digit keys zone：

【0－9】key：Under setting，use for select digit. During playback and preview，1、2、

3、4 is for the switch of the channels

【＋】、【－】key：adjust digit when plus or deduct

【ENTER】key：under setting，means select and save

On playback condition, press ENTER can reveal parameters in OSD OVERLAY menu

when it’s ON on screen.

Other function keys :

Figure 8 Other function keys on remote control

Startup/power off Through screen， press this button twice for reboot（soft start key）

（note：can’t be use now）

LOGIN

When setting password，press LOGIN input password。

Do please remember password due to device have no reset

- 12 -

function.

INFO Check info

Digit keys1,2,3,4

Switch between 1-channel and 4-channel version. Press it, show

4-channel. Press digit key 1,2,3,4, can separately switch to

CH1,CH2,CH3,CH4

RETURN Return to up grade, exit setup menu and return to screen.

PAUSE / STEP When playback recording, press STEP, a time play a step, press

PAUSE, it stop. Press play key, then normally play.

GOTO When play back, press it can jump to designated time and play.

FRAME Press FRAME key, then FRAME play.

（PLAY） PLAY key, （when PAUSE, it will show still image）

FWD FWD for playback recording, 4 grades: 2X，4X，8X，16X

REW REW for playback recording, 4 grades: 2X，4X，8X,16X

Stop manual recording key

Start manual recording key

NEXT Turn to next page/ next file when playing.

PREV Turn to previous page/ previous file when playing

AUTO、PRESET、

ZOOM+/- 、

FOCUS+/- 、

IRIS+/- 、 PTZ 、

PRESET 、

RECALL、BRUSH

PTZ function keys

F1、F2、F3 F1 is shortcut key，F2,F3 are Spare keys. (Reserved for future)

5 Device Functions and Operation Guide

The System include eight modules :system setup、record setup、vehicle setup、common tools、

- 13 -

playback、Shortcut、Module management、system information.Main menu refer to Picture9 Function structure refer to Picture10.

Notice:

1.All of below sub-menu setting will only be effective after confirm”Save”,Otherwise the setting

is noneffective.

2.The Check Box has been “checked” means selected the function;unchecked means not selected

the function.

3.Number enter could use both the number key in the IR Remote and soft keyboard.While the

number enter coulde only use the soft keyboard.Press “Return” to back to the Sub-menu.

Pic.9:Main Menu

- 14 -

Pic.10:Function Structure

- 15 -

5.1 Login Menu

Note：After power on, press LOGIN key on the IR Remote to login the setting system.as

below:：

Original User:Admin Original PSW:111111

Pic:Login Window

Explanation：

1.Device No.:Set the Series No.for each device.It will show on the right side of the series No.input 9frame.Users just input the same No. as it show 2.User’s Name:Including admin and regular user.Admin permission:Enable to set the data Regular user permission:Could only check,look up menu info,couldn’t set the menu and data. 3.Password:Input the user’s name and password,press down arrow to log in.If the password is incorrect,press up key and then press cancel ,re-enter the right password. Both original passwords for regular user and admin are:111111

5.2 System Settings

System settings including four fuction options:Basic,Power,Network,Password. As below:

- 16 -

Pic12:System Settings

5.2.1 Basic Settings

Set the basic information of the device.As below:

Pic13:Basic Setting

Instruction:

1. Date type: press ENTER for switch Y-M-D/ D-M-N.

2.Date,time setting:Press”ENTER”,and then press”-“ or “+” to set the data,press enter to confirm.

3.Set “Opr timeout” and “Dev num”:Press Cancel and then press the numbers.

4. "COMPANY NAME", "VEHICLE NO", "DRIVER NAME",”LINE NUM” Setting:Pre【Enter】 key to pop up keyboard window, then use left/right/up/down/enter key to setup.

5. Select “SAVE” and press 【ENTER】to save the settings.

- 17 -

5.2.2 Power off/on Setting

Power off/on setting window as below:

Pic14：Power off/on Setting

Instruction：

1.Power Mode:On(power on when the vehicle start)/Timing.Press “Enter” to switch

2.Power off Delay:ACC/OFF.Press “Enter”to switch.If choose ACC,the user could also set the delay time.Press “Cancel” to input the number keys.(Note:Time range usually is 3-240min).After setting this,the DVR will continue recording to the appointed time after the vehicle turned off

3.Power on/off Time:When you set the timing power mode,you should also set this power on/off time.After setting this,the DVR will auto power on/off according to this time schedule.

5.2.3 Network Setting

Network setting window,as below:

- 18 -

PIC.15:Network Setting

Instruction：

1.Local Network:Local network connected by CATV broadband.

Mainly for testing,barely used,need not pay much attention to it.

IP Address,Netmask,Gateway setting:All press “Cancel”first,and then press number key for input new data;

Mac Adress Setting:Press “Enter”to enter the soft keyboard,press direction key,then press”Enter” to choose the right address.

2.Center Setting:

Server IP:Set the CMS Center Server IP as this “Server IP”

Control Port:Gateway Server Port Number.Usually is “8501”

Press “Cancel” to pop up the number keyboard to set above data.

5.2.4 Password Setting

Password Setting window as below：

- 19 -

Pic.16：Password Setting

Instruction：

1、PSW Enable:Press “Enter ” to switch on/off

2、User’s PSW and Admin PSW could only be revised by admin.

Press “Cancel” to pop up the number keyboard and revise the new PSW.

Press down key to go to”Save”,press”Enter” to save the setting,then return.

5.3 Record Setting

Recording Setting:Normal,Channel,Time List,Sub-stream.As below:

Pic.17:Recording Settings

5.3.1 General Setting

As below Picture:

- 20 -

Pic.18:Normal Setting

Instruction：

1．Signal System:Press “Enter”to select PAL/NTSC。

2．Rec Mode:Press “Enter”to choose select Auto/ Alarm/Timed.

3．PACKET TIME: Press “Enter” select 15/30/45/60。

4．OVER WRITTEN: Press “Enter” select ON/OFF。

5．ALM PRE(S): When the alarm occurred,it will pre-record a period and packing to the Alarm video.Press”Cancel”, then press digit key (time range 0S-- 60S).

6．ALM REC DELAY(S): When the alarm stop,it will keep recording a period and packing to the alarm video.

Press “Cancel”, then press digit key (delay range 30—900).

7. ALM OUTPUT TIME(S): Press “Cancel”, then press digit key(5S---240S).

8．REC PROTECT TIME: To set the reserve time for the alarm videos.During the protect time,even the SD Card is full,the alarm video will not be overtaken.

Press “Enter”, select 1/3/5/7/10/15

9．REC VEHICLE INFO: Press ON/OFF.When set ”on” it will write all the alarm info,GPS info ect. Into the video,which could be found through playback analysis software afterwards.

5.3.2 Channel Setting

Channel Setting as below,

- 21 -

Pic.19：Channel Setting

Instruction：

1.Press Direction key set up the Channel, select CH1 Enable, then press ENTER-ON/OFF, Press right key select resolution ratio, then press ENTER select D1/HD1/CIF。The same settings for FRM（01----30 optional）, QUAL（1---8 level, 1level is the best）, AUDIO, PREVIEW as Res.

2.The same setting for CH2、CH3、CH4 as CH1.

5.3.3 Record Schedule Menu

Pic.20 Record Schedule Menu

Instruction:

1． Press in the digit zoon, and then press digit key, press , then press digit key to set

each time frame.Press direction key to move to defferent day and time frame.

- 22 -

5.3.4 Sub-Stream Setting

Pic.20:Sub Stream Setting

Instruction:

1．Bit rate setting:16/24/32/40/48/56/64/72/80/96/128/160/200/256/384 optional.

This bit rate is the transmission speed rate for one channel.

2. Frame /second setting 01/02/03/04/05/07/10/13/15/20/23/25 optional.

5.4 Vehicle Info

Vehicle info：Sensor, Speed, Accelerate, Temperature

- 23 -

Pic.22:Vehecle Info

5.4.1 Sensor Setting

Pic.23：Sensor Setting

Instruction:

1.Users define different sensor’s name according to different interface when install and set the MDVR.Press “Enter” to pop up the soft keyboard and input corresponding names.

2.Enable on means open up the sensor,off means close.In the condition of Enable on,user can select Record on/off,Alarm on/off.Press “Enter” to switch.

5.4.2 Speed

- 24 -

Picture 24: Speed setting

Note：

1.SPD SOURCE(SPEED SOURCE) : GPS/VEHICLE，Press ENTER to switch。

2．SPD ADJUST: Press CANCEL，then press digit key。P/S(PULSE/SECOND): Press CANCEL，then press digit key to change the p/s.

3．SPD UNIT: KM/MPH, Press ENTER for switch.

4．Low speed ALM Enable: press ENTER, select ON/OFF；then press right key,

press CANCE, then press digit key set up Threshold, press right key, then press

ENTER set up the Record ON/OFF.

5．High speed ALM Enable: the same setting as low speed ALM Enable.

5.4.3 Accelerate

Accelerate set

Note： 1．X setting: Press Direction key, making the setting on the X enable , then press ENTER—select ON/OFF; press right, then press CANCEL, then press digit key set up the Threshold, press right, then press ENTER---select ON/OFF.

2．Y、Z: the same setting as X。

5.5 Manage Tool

Manage tools：Format、Configuration、Upgrade、Log，Motion Detection

- 25 -

Picture 26: Manage Tool

5.5.1 Format

Picture 27: Format

Note:Press ENTER to select SD1/SD2, then press right key, press ENTER to select format or not.

Warning：Once executing Format,all the data in the device will lost . For sure to do this action, press FORMAT . Or else, press CANCEL.

- 26 -

5.5.2 Configuration Management

Picture 28: Configuration

Note：

1.When execute export Cofiguration, The configuration information will save in SD1 Card,

2. Press New configuration import into information for the same setting MDVR.

3, Press Reset setting , then the MDVR will recover the setting at the time when leave factory.

5.5.3 Upgrade

Press down key for Reset settings，then press ENTER，system remind message.For sure to reset, press ENTER. Or else, select EXIT.

Picture 29: Upgrade

- 27 -

Note： System upgrade including: file system, application, Press ENTER 。

5.5.4 Log Management

Picture: LOG Search Menu

Note： Press direction key to START TIME &END TIME, then press the digital key to put into time.

5.5.5 Motion Detection

Go into “Motion Detetion” ,as picture 31 :

- 28 -

Picture 31 : Motion detetion setting

Picture 32: District Selected Note: In the districted selected, once there is a object moving, the system will detect it, then will send out alarm event which will save in LOG naming MD ALARM; If the alarm continue or happen several times in 30 Second, then system will record the alarm event every 30 Seconds. User can check these alarm events in the LOG menu, as picture 30. If the alarm event happen when user setting the packing time, this alarm event will be packaged as alarm recorder. User can check the alarm event by playback the recorder. When the channel is in ON, It shows this channel has start using motion detetion. The detetion choose the district for user . Choose “Configuration”, enter to the picture 32, choose one diamonds of them firstly (the diamonds will become green), then choose other diamond, the rectangle district form in opposite angles by the two diamonds( once the district was chose, this district become green), please press cancel key in remote control to cancel the district chose, as picture 32. The levels of sensitivities is low, middle, high. In the high sensitivity , it can sense the light change, in the low sensitivity, it just can detect the moving object. Press “ save”, when it shows “save success”, it means the setting is success.

- 29 -

5.6 Play back

Picture 33 : Searching video

Note：1．REC TYPE:ALL/ALARM（ALM REC）Press ENTER。

2．CHANNEL: SD1/SD2, Press ENTER。

3．DATE、START TIME, END TIME, Press left/right key, then press digit key.

5.7 Quick setup

5.8 Module Management

Module Managemement setup: Wireless setup、WIFI setup and PTZ

- 30 -

Picture 34 Module Management

5.8.1 Wireless Setup

When the DVR connect network though 3G,we need to set network here :

Introduction:

1. According to the communication conficuration of the device, insert the corresponding SIM card, support WCDMA and EVDO. SIM card is on the communication board ,move the small baffle under the main board , you can see the interface of the SIM card.

2. Insert 3G wireless antenna, as picture 35:

Insert 3G antenna

Picture 35 3. Edit the following information on WIFI setup interface:

1) Set up the wireless dialing status as ON , press ENTER to shift;

2) Choose communication type ,if the device support WCDMA ,then choose WCDMA,if it support EVDO ,then choose EVDO , press ENTER to shift it ;

3) Access point and center No are usually kept ,no need change,input the user name and password of your SIM card , keep blank if no ,press ENTER to edit .

As picture 36:

- 31 -

Picture 36: Wireless setup

4. Press INFO key of remote control, you can see the related information of 3G communication ,if show dial successful, then 3G setting-up is finished ;

5. If need connect with CMS server , input CMS center IP and port No on center IP column of picture 15.

5.8.2 WIFI Setup

Intruction:

1. Insert WIFI antenna , as picture 37:

Insert WIFI antenna picture 37

2. Edit the following information on WIFI setting interface:

1. Set up ENABLE and ENCRYPT as ON status , AUTH MODE including WPA，

- 32 -

WPA-PSK，OPEN and SHARE , ENCRYPT type are TKIP and AES. At present , AUTH MODE is not act , so pls choose OPEN status (no need authentication), then WIFI can work , choose WEP on ENCRYPT TYPE.Press ENTER to shift and set the above information.

2. Input SSID and password , set up IP and gateway .Press ENTER to set up SSID and password , press CANCEL to set up IP and gateway.

As picture 38:

Picture 38:WIFI setup 3. Check system information , as picture 42, if WIFI singal is over 60 d B, it means WIFI has

connected with network; 4. If connect with CMR server, input the CMS center IP and port No on center IP column of

picture 15..

5.8.3 PTZ setup

Because of the PTZ from different supplier are vary ,so their parameters are also different. When we control the PTZ ,the parameter we set up should match the parameter of PTZ device. For example , we use one model of Shenzhen Minrray Industry Co.,Ltd for configuration below: 1. PTZ include two DIP switchs: SW1 and SW2, SW1 is for setting up communication protocol

and baud rate. Choose control protocol on 1.2 bit of SW1;But we control protocol on the PTZ setup of DVR, as picture 37, press ENTER of remote control to choose P or D protocol , choose RS485 port 120Ω switch on 3-6 bit, choose baud rate on 7-8 bit, as picture 39. press ENTER to choose baud rate（1200b，2400,4800b，9600b）, the baud rate we choose should match the switch control of PTZ . For example, if we choose 2400b on DVR setup,then SW1-7 of PTZ should be ON , SW1-8 should be OFF, and the like.SW1switch control as picture 40 :

Control

protocol Baud

rate

Receive

location

- 33 -

Picture 39：PTZ setup

Picture 40:PTZ SW1 setup 2. SW2 is mainly for setting up location reception, and protocol P location setup as picture 41,

Protocol D location setup as picture 40, as CH1 channel in picture 37: NUM ( receive location)the location is 1, protocol is D,then we need to set up SW2 switch according to protocol D location1 in picture 42, SW1 should be ON , others should be OFF.NUM selection: Press ENTER of remote control and use the soft keyboard to input .

- 34 -

Picture 41: Protocol P location setup

Picture 42:Protocol D location setup

3. Dbit is data bit ,usually is 8, we can choose 1-8 here ; sbit is stop bit ,choose 1 and 2

here ;CHECK is check bit, it ‘s none.

- 35 -

5.9 System Information

Picture 43:system information

Picture 44:system information Note: Press ENTER to shift up and down page.

- 36 -