SCR Applications

HomeAboutDatasheetsLab ManualTesting Components

« Full wave rectifier using SCRVersatile emergency lamp. »

SCR Applications

jojoSeptember - 15 - 2009

Ads by Google DC Power Supply Circuit Project LED Circuit Electronics Circuit

SCR Applications http://www.circuitstoday.com/scr-applications

1 of 25 1/5/2011 7:43 PM

The ability of an SCR to control large currents to a load by means of small gate current makes the device very useful in switchingand control applications. A few of the possible applications for the SCR are listed in the introduction to SCR blog post.

Here we will consider six applications of SCR like power control, switching, zero-voltage switching, over-voltage protection,pulse circuits and battery charging regulator.

1. Power Control.

SCR Power Control Circuit

SCR Power Control Circuit

Because of the bistable characteristics of semiconductor devices, whereby they can be switched on and off, and the efficiency of gatecontrol to trigger such devices, the SCRs are ideally suited for many industrial applications. SCRs have got specific advantages oversaturable core reactors and gas tubes owing to their compactness, reliability, low losses, and speedy turn-on and turn-off.

The bistable states (conducting and non-conducting) of the SCR and the property that enables fast transition from one state to the otherare made use of in the control of power in both ac and dc circuits.

Electric DC Motors Hansen-Motor.com/Request-a-Quote

Electric motors - custom for you. Needquote/sample? Learn more now!

RF Bandpass & duplexers www.anatechelectronics.com

Custom and Std. bandpass, duplexers lowpass,highpass bandstop filters

AC DC Power Supply www.digipwr.com

High Grade High Efficient Flexible Standard andCustom Power Systems

RF and DC Power Supplies www.ptb-sales.com

Vacuum deposition, etching, sputter Sold testedwith 90 day warranty

7Share


2 of 25 1/5/2011 7:43 PM

SCR Phase ControlSCR Phase Control

In ac circuits the SCR can be turned-on by the gate at any angle α with respect to applied voltage. This angle α is called the firing angleand power control is obtained by varying the firing angle. This is known as phase control. A simple half-wave circuit is shown in figure a.for illustrating the principle of phase control for an inductive load. The load current, load voltage and supply voltage waveforms are shownin figure b. The SCR will turn-off by natural commutation when the current becomes zero. Angle β is known as the conduction angle. Byvarying the firing angle a, the rms value of the load voltage can be varied. The power consumed by the load decreases with the increase infiring angle a. The reactive power input from the supply increases with the increase in firing angle. The load current wave-form can beimproved by connecting a free-wheeling diode D1, as shown by the dotted line in fig-a. With this diode, SCR will be turned-off as soon asthe input voltage polarity reverses. After that, the load current will free wheel through the diode and a reverse voltage will appear acrossthe SCR. The main advantage of phase control is that the load current passes through a natural zero point during every half cycle. So, thedevice turns-off by itself at the end of every conducting period and no other commutating circuit is required.

Power control in dc circuits is obtained by varying the duration of on-time and off-time of the device and such a mode of operation iscalled on-off control or chopper control. Another important application of SCRs is in inverters, used for converting dc into ac. The inputfrequency is related to the triggering frequency of SCRs in the inverters. Thus, variable frequency supply can be easily obtained and usedfor speed control of ac motors, induction heating, electrolytic cleaning, fluorescent lighting and several other applications. Because of thelarge power-handling capacity of the SCRs, the SCR controlled inverter has more or less replaced motor-generator sets and magneticfrequency multipliers for generating high frequency at large power ratings.

Operation of Power Control in SCR

A commonly used circuit for controlling power in load RL using two SCRs is shown in figure. Potentiometer R controls the angle ofconduction of the two SCRs. The greater the resistance of the pot, lesser will be the voltage across capacitors C1 and C2 and hence smallerwill be the time duration of conduction of SCR1 and SCR2 during a cycle.

During positive half cycle capacitor C2 gets charged through diode D1, pot R, and diode D4. When the capacitor gets fully charged,(charge on the capacitor depending upon the value of R) it discharges through Zener diode Z. This gives a pulse to the primary and therebysecondary of the transformer T2. Thus SCR2, which is forward biased, is turned on and conducts through load RL. During negative halfcycle similar action takes place due to charging of capacitor C1 and SCR1 is triggered. Thus power to a load is controlled by using SCRs.

2. Switching.

Thyristor, being bistable device is widely used for switching of power signals owing to their long life, high operation speed and freedom


3 of 25 1/5/2011 7:43 PM

from other defects associated with mechanical and electro-mechanical switches.

AC Circuit Breaker using SCR

Figure shows a circuit in which two SCRs are used for making and breaking an ac circuit. The input voltage is alternating and the triggerpulses are applied to the gates of SCRs through the control switch S. Resistance R is provided in the gate circuit to limit the gate currentwhile resistors R1 and R2 are to protect the diodes D1 and D2 respectively.

For starting the circuit, when switch S is closed, SCR1 will fire at the beginning of the positive half-cycle (the gate trigger current isassumed to be very small) because during positive half cycle SCR1 is forward biased. It will turn-off when the current goes through thezero value. As soon as SCR1 is turned-off, SCR2 will fire since the voltage polarity is already reversed and it gets the proper gate current.The circuit can be broken by opening the switch S. Opening of gate circuit poses no problem, as current through this switch is small. As nofurther gate signal will be applied to the SCRs when switch S is open, the SCRs will not be triggered and the load current will be zero. Themaximum time delay for breaking the circuit is one half-cycle.

Thus several hundred amperes of load current can be switched on/off simply by handling gate current of few mA by an ordinaryswitch. The above circuit is also called the static contactor because it does not have any moving part.

DC circuit breaker


4 of 25 1/5/2011 7:43 PM

SCR Application-DC Circuit Breaker

As shown in figure, Capacitor C provides the required commutation of the main SCR since the current does not have a natural zero valuein a dc circuit. When the SCR1 is in conducting state, the load voltage will be equal to the supply voltage and the capacitor C will becharged through resistor R. The circuit is broken by turning-off SCR1. This is done by firing SCR2, called the auxiliary SCR. Capacitor Cdischarges through SCR2 and SCR1. This discharge current is in opposite direction to that flowing through SCR1 and when the twobecome equal SCR2 turns-off. Now capacitor C gets charged through the load and when the capacitor C gets fully charged, the SCR2tums-off. Thus the circuit acts as a dc circuit breaker. The resistor R is taken of such a value that current through R is lower than that ofholding current.

3. Zero Voltage Switching.


5 of 25 1/5/2011 7:43 PM

SCR Switching Application

In some ac circuits it is necessary to apply the voltage to the load when the instantaneous value of this voltage is going through the zerovalue. This is to avoid a high rate of increase of current in case of purely resistive loads such as lighting and furnace loads, and therebyreduce the generation of radio noise and hot-spot temperatures in the device carrying the load current. The circuit to achieve this is shownin figure. Only half-wave control is used here. The portion of the circuit shown by the dotted lines relates to the negative half cycle.Whatever may be the instant of time when switch S is opened (either during the positive or the negative half cycle), only at the beginningof the following positive half-cycle of the applied voltage SCR1 will be triggered. Similarly, when switch S is closed, SCR1 will stopconducting at the end of the present or previous positive half-cycle and will not get triggered again. Resistors R3 and R4 are designed onthe basis of minimum base and gate currents required for transistor Q1 and SCR1. Resistors Rl and R2 govern rates of the charging anddischarging of capacitor C1 Resistor R5 is used for preventing large discharge currents when switch S is closed.

4. Over-Voltage Protection.


6 of 25 1/5/2011 7:43 PM

Over Voltage Circuit Protection

SCRs can be employed for protecting other equipment from over-voltages owing to their fast switching action. The SCR employed forprotection is connected in parallel with the load. Whenever the voltage exceeds a specified limit, the gate of the SCR will get energizedand trigger the SCR. A large current will be drawn from the supply mains and voltage across the load will be reduced. Two SCRs areused—one for the positive half-cycle and the other for negative half-cycle, as shown in figure. Resistor R1 limits the short-circuit currentwhen the SCRs are fired. Zener diode D5 in series with resistors Rx and R2 constitutes a voltage-sensing circuit.

5. Pulse Circuits.

SCR-Pulse Circuit

SCRs are used for producing high voltage/current pulses of desired waveform and duration. The capacitor C is charged during the positivehalf cycle of the input supply and the SCR is triggered during the negative half-cycle. The capacitor will discharge through the outputcircuit, and when the SCR forward current becomes zero, it will turn-off. The output circuit is designed to have discharge current of lessthan a milli-second duration. The capacitor will again get charged in the following positive half-cycle and the SCR will be triggered againin the negative half-cycle. Thus the frequency of the output pulse will be equal to the frequency of the input supply. For limiting thecharging current resistor R is used. High voltage/current pulses can be used in spot welding, electronic ignition in automobiles, generationof large magnetic fields of short duration, and in testing of insulation.

6. Battery Charging Regulator.


7 of 25 1/5/2011 7:43 PM

Battery Charging Regulator

The basic components of the circuits are shown in figure. Diodes D1 and D2 are to establish a full-wave rectified signal across SCR1 andthe 12 V battery to be charged. When the battery is in discharged condition, SCR2 is in the off-state as will be clear afterdiscussion. When the full-wave rectified input is large enough to give the required turn-on gate current (controlled by resistor R1), SCR1will turn on and the charging of the battery will commence. At the commencement of charging of battery, voltage VR determined by thesimple voltage-divider circuit is too small to cause 11.0 V zener conduction. In the off-state Zener diode is effectively an open-circuitmaintaining SCR2 in the off-state because of zero gate current. The capacitor C is included in the circuit to prevent any voltage transientsin the circuit from accidentally turning on of the SCR2. As charging continues, the battery voltage increases to a point when VR is largeenough to both turn on the 11.0 V Zener diode and fire SCR2. Once SCR2 has fired, the short circuit representation for SCR2 will result ina voltage-divider circuit determined by R1 and R2 that will maintain V2 at a level too small to turn SCR1 on. When this occurs, the batteryis fully charged and the open-circuit state of SCR1 will cut off the charging current. Thus the regulator charges the battery whenever thevoltage drops and prevents overcharging when fully charged. There are many more applications of SCRs such as in soft start circuits, logicand digital circuits, but it is not possible to discuss all these here.


8 of 25 1/5/2011 7:43 PM

Related Posts

SCR Control circuitsSCR as Half Wave RectifierFull wave rectifier using SCRTriac ApplicationsVoltage MultipliersSCR Turning OFF methodsTurn on methods of an SCRRECTIFIER CIRCUITS USING PN JUNCTION DIODESShunt capacitor filterDiode Clippers

Random Posts

Lamp pulser circuitAll pass filtersTriggering of Flip FlopsCharacteristics of JFETSV-Groove MOS (VMOS)Class A power amplifiersKIOCL is hiring Graduate Engineer TraineesTouch Switch Circuit using NE 555Dual power supply using L165

Electric DC Motors Hansen-Motor.com/Request-a-Quote

Electric motors - custom for you. Needquote/sample? Learn more now!

RF Bandpass & duplexers www.anatechelectronics.com

Custom and Std. bandpass, duplexers lowpass,highpass bandstop filters

AC DC Power Supply www.digipwr.com

High Grade High Efficient Flexible Standard andCustom Power Systems

RF and DC Power Supplies www.ptb-sales.com

Vacuum deposition, etching, sputter Sold testedwith 90 day warranty


9 of 25 1/5/2011 7:43 PM

ShareThis

Translate

Gadgets powered by Google

Get updates via Mail for Free

Delivered by FeedBurner


10 of 25 1/5/2011 7:43 PM

Posted in TutorialsTags: SCR, Thyristors

10 Responses to “SCR Applications”

IFTIKHAR says:September 15, 2009 at 4:16 pm

very usefull circuit

1.

Bade3 says:January 1, 2010 at 5:33 pm

good circuits , can i get some real circuit for 100 watt ac power controller ?thanks all

2.

jay clark says:January 21, 2010 at 1:11 am

thank u!!

3.

chandra says:January 23, 2010 at 12:29 am

very very well&good.

4.

Danny says:April 16, 2010 at 10:08 pm

5.


11 of 25 1/5/2011 7:43 PM

I wonder if you could perhaps help with values to the full wave speed control using 2 SCR’s and caps, diodes and pot to adjust thepoint on the wave of starting to conduct for both half cycles.

I need it to switch currents on 250V AC with currents up to 6A. I am using SCR’s rated at 8A. My circuit veroboard just blew upafter 30years. It was a trade test project way back in the 1970′s

Edgardo Diolola says:June 16, 2010 at 12:39 am

Good day..May I know the exact specification on every component if this circuit?Thanks a lot.

6.

Edgardo Diolola says:June 16, 2010 at 12:41 am

Good day..May I know the exact specification on every component if this circuit? (BATERY CHARGING REGULATOR CIRCUIT)Thanks a lot.

7.

seetharaman says:June 16, 2010 at 2:51 am

Hi Edgardo this is only an indication of different type of SCR application. a typical cicuit can be seen onhttp://www.circuitstoday.com/battery-charger-circuit-using-scrthe project

8.


12 of 25 1/5/2011 7:43 PM

Adena Zona says:September 2, 2010 at 5:42 pm

The 3 phase electric power is common way of alternating current transmission and it is a type of polyphase system and is the normalway used by electric power distribution grids to distribute power. That looks like exactly the 3 phase alternator I’ve been lookingfor.

9.

SURAJIT SAMANTA says:November 3, 2010 at 7:46 am

really it is very helpul for me.

10.

Leave a Reply

Name (required)

Mail (will not be published) (required)

Website

Search


13 of 25 1/5/2011 7:43 PM

Custom Search

Get Daily Updates via Email

Delivered by FeedBurner

Category

555 Timer IC (11)amplifiers (8)Audio Circuits (80)Automotive Circuits (25)Battery Related (20)Bells & Tone generator circuits (20)Cable TV (1)Camera (5)Clipping and Clamping Circuits (7)Clocks & Timers (2)Components (31)Conversion Circuits (4)Counter Circuits (2)Counters (3)Digital Electronics (7)Electronic Books (1)


14 of 25 1/5/2011 7:43 PM

Electronic Circuits Lab (11)Electronic Keys & locks (3)Electronics Jobs (4)Events (2)Fan related (1)Filter Circuits (16)Fire Alarm (3)Fun & Game (9)Fun Stuff (8)Gadget Reviews (2)Gadgets (1)Ham Radio Circuits (2)High Voltage Circuits (1)Home Circuits (34)Industry (13)Instruments (12)Integrated Circuits (18)Inverters & UPS (6)Lab Manuals (15)Light Related (15)Lighting Circuits (38)Microcontroller Lab (1)Microcontrollers (1)Microprocessor Lab (9)Mobile Phone Related (1)Motor Related (10)Multimeters (1)Notebooks (1)Oscillators (25)PC (1)Peripheral Interface Controller (PIC) (2)Power Controller Circuits (8)Power Supplies (53)Project Ideas (1)Projects (1)


15 of 25 1/5/2011 7:43 PM

Proximity Detectors (3)Radio Circuits (22)Radio Transmitters (15)Relay (3)Remote Circuits (11)Robotics (1)Security & Saftey (14)Sensor Circuits (14)Signal Conditioners (2)Signal Generators (13)Speed Controller Circuits (1)Switching Circuits (5)Tech News (11)Telephone Related (9)Television Related (3)Temperature Related (3)Test & Measurement Circuits (35)Testing Components (9)Three phase circuits (1)Timer Circuits (2)Transmitters (7)Tutorials (132)Uncategorized (11)USB Circuits (2)Videos (4)VLSI (36)Voltage Regulators (10)

Most Discussed

150 Watt amplifier circuit (370)100 Watt sub woofer amplifier. (211)Suggest a Topic to Publish & Win a 8GB Pen Drive (202)Automatic LED Emergency Light-Modified Version (171)


16 of 25 1/5/2011 7:43 PM

Automatic LED Emergency Light (139)Mains Operated LED Circuit (108)Infrared motion detector circuit (103)Simple Water Level Indicator (95)Battery charger circuit using SCR. (91)2 km FM transmitter (90)Lead acid battery charger circuit (82)100 Watt inverter circuit (79)40V dual power supply (72)Long Range FM Transmitter 1 (66)Electronic mosquito repeller (58)


17 of 25 1/5/2011 7:43 PM

Pages


18 of 25 1/5/2011 7:43 PM

AboutDatasheetsLab Manuals

Electronic Circuits LabMicrocontroller labMicroprocessor Lab

Privacy PolicyProject ContestsTesting Components

Recent Posts

Stereo sound level indicatorAugmented Reality (AR) Technology3 channel audio splitterApply for Technical Assistant/Project Design Engineer at IIT BombayLow pass filter for subwooferRemote Operated Spy Robot CircuitApply for Application Engineer post at KLA Tencor CorporationKIOCL is hiring Graduate Engineer TraineesRemote Control Circuit Through RF Without MicrocontrollerPYROS 2K11 – National Level Technical FestivalBasics of MicrocontrollersHappy New Year to EveryoneIntroduction to PICApply for Research Assistant & Technical Assistant Post in NIT TiruchirapallyAnnouncing Winner of Suggest a Topic to Publish Contest

Random Posts


19 of 25 1/5/2011 7:43 PM

Electromagnetic field sensor circuit

Channeling Effect of Gallium Arsenide (GaAs)

Working of Scanner


20 of 25 1/5/2011 7:43 PM

Op-Amp Comparator

Active Filter Types

2 x 32 Watts stereo amplifier


21 of 25 1/5/2011 7:43 PM

LASCR-Light Activated SCR

Mains failure alarm circuit


22 of 25 1/5/2011 7:43 PM

Capacitance meter using LM2917

Sound pressure meter

Follow Us in Facebook


23 of 25 1/5/2011 7:43 PM

Rahul Karthick Aman 昌昌 Babukuttan

Andrei Jithin Thoufeeq Hesham Mantas

Circuitstoday.com on Facebook

2,026 people like Circuitstoday.com

Like

Circuitstoday.com on Facebook

Recent Comments

akash gopi on 100 Watt inverter circuitjojo on Remote Control Circuit Through RF Without MicrocontrollerSeetharaman on Lead acid battery charger circuitG P Koruthu on Remote Control Circuit Through RF Without MicrocontrollerVALENTINAS on Lead acid battery charger circuitkamal on One transistor code lockkamal on One transistor code lockamin on Happy New Year to EveryoneSeetharaman on Automatic LED Emergency Lightrashid on Announcing Winner of Suggest a Topic to Publish Contest

Blogroll

Electrical circuitsSeminar Topics


24 of 25 1/5/2011 7:43 PM

Recent Posts

Stereo sound level indicatorAugmented Reality (AR) Technology3 channel audio splitterApply for Technical Assistant/Project Design Engineer at IIT BombayLow pass filter for subwooferRemote Operated Spy Robot CircuitApply for Application Engineer post at KLA Tencor CorporationKIOCL is hiring Graduate Engineer TraineesRemote Control Circuit Through RF Without MicrocontrollerPYROS 2K11 – National Level Technical Festival

Popular Tags

1.3V power supply 2N2222 2N3055 15A power supply 555 IC 555 timer 8085 lab manual AM demodulator amplifier circuit amplifiers AM radio Am receiver circuit

audio circuit battery charger Camera CCD circuit design circuit diagram Clippers CMOS Active Pixel Sensor Components current

amplifier circuit device protection Diac Digital Electronics diode Electron-Beam Lithography electronic circuit Electronic Circuits ElectronicInstruments electronics circuits lab emergency light crcuit fabrication technique Filter Circuits Fire alarm circuit FM stations FM transmitter Gadget Reviews high

current power supply. 12v 15A power supply hobby circuits hobby projects Home Circuits IC Integrated Circuits Inverters Lab Manuals LED

lighting circuit Light to Frequency converter circuit Liquid Crystal Display Mains Operated LED microphone preamplifier microprocessor lab manual NE555 NE555timer Oscillators Phase Locked Loops PIC Plasma Display PLL pn junction Power Amplifiers Power Supplies power supply power supply using L200 radio circuit

Relay replacement for 1.3V mercury cell Resistors SCR Signal Generators simple am radio simple lamp flasher soft start power supply soft start powersupply using L200 stereo loine driver

circuit subwoofer filter tachometer circuit Tech News Thyristors timer circuit Timer IC Triac Tutorial Tutorials Videos video telepresence VLSI Voltage

Multipliers Voltage Regulator Voltage Regulators


25 of 25 1/5/2011 7:43 PM

Documents

SCR Applications