Upload
nitinmg
View
9
Download
0
Tags:
Embed Size (px)
DESCRIPTION
SBC9302 Procedure
Citation preview
OVERVIEW.!Basic of ARM9 Controller.
Important Steps.
Linux installation.
SPJ tools installation i.e. workspace
installation.
How to operate board of ARM9
Controller.
STEPS.!Features of ARM9 i.e.SBC_9302.
Installation of Linux_Mandriva.
Installation of MINICOM Terminal
& TFTP server.
Ethernet Setup.
Workspace Installation
TFTP Setting & Bash profile Setting.
FEATURES!
ARM9 ControllerEP9302 32Bit.
Cirrus Logic Controller EP9302 &
Speed_ @200 Mhz.
Ethernet Support 10 to 100Mbps.
USB Device & USB Host.
FEATURES!
RAM Memory SDRAM_32MB.
Flash Memory_16MB.
Serial Port Support:-
RS232,RS485/RS422
Memory Card Interface.
FEATURES!
Channel:-
1. 16 bit ADC Channel.
2. PWM Channel.
SD Card Interface.
104 PC Expansion Bus.
LINUX
INSTALLATION!
Space For Installation :- 40 GB to
80 GB
Partition :-
1. Root (/):- 16 GB to 25 GB.
2. Swap:- 4 GB to 8 GB.
3. Home:- Remaining space.
LINUX
INSTALLATION!
Graphical User Interface:-
1. KDE(K Desktop
Environment).
Installation Packages.
MBR(Memory Boot Reader).
MINICOM
TERMINAL!
Double Click on "Install & Remove Software
1.Firstly Go to start
This window will appeared.
1.Here Find minicom & install it i.e. click on Apply button..2.All process Given below,3.Important Notes:- In Mandriva_2010 Minicom must be installed externly,Only these procedure is available in Mandriva_2007 .4.So in Mandriva_2010 It must be install external
Such window will appeared & Then say Yes
1.When above process gets completed then our Minicom will installed successfully.
EXTERNAL COPY PROCESS!
Firstly copy binary file of minicom from CD sbc9302_tools in Home of Linux operating system which is on Desktop.
Then open konsole terminal . Then give command su & press enter also need of root
password. After root login give command cd /home/maahi(user name)/ &
press enter. Then give command ls & press enter "for ensure that we are
in home folder . Then give command cp minicom /usr/bin/ & press enter Our minicom binary file will be copied at its destination.
TFTP
SERVER.!
Double Click on "Install & Remove Software
This window will appeared.
This Window will appeared. Then Find TFTP
tftp
select All "here.
Find TFTP & select last two option.
Such window will appeared & Then say Yes
When bellows process gets completed then our TFTP server will install successfully.
MAKE!
Also find make & select Make Say "apply
Such window will appeared & Then say Yes
GCC(GNU Code
Compiler.)!
Find gcc & Select it
Say Apply
Such window will appeared & say Apply
After Installation .Click on Quit button.
Select Security Option & above option will appeared!
click on Set up your personal firewall icon.
Select Everything (no firewall) icon & say OK.
Right click here & select Network configuration above window will appeared.
Select Wired(Ethernet) & say Next.
Such window will appeared Select eth0& then say "Next
Such window will appeared Then select "Manual configuration& then say "Next
Such window will appeared then Give require IP address You can give any & fill all these thing given here . say "Next
Such window will appeared Select last two option then say "Next
Such window will appeared Select Yes& then say "Next
1.Firstle open console terminal as shown below.2.Then give command su -3.Then give our root password. 4.All process shown below,
1.After that just give command shown as below i.e. cd /home/maahi(user name)/Desktop/cd_image(folder name)/
Then press "enter2.Now we are in our folder where we have copy on Desktop.
Here we can ensure that we are in destination folder by giving command ls as shown below.i.e.It show file which is in our folder.
1.Here for workspace installation we required to run any file from,a.gui_install.dh. b.install.sh. c.user_install.sh. d.install_original.sh.
2.Here I am running file user_install.sh by giving command sh user_install.sh such as shown below.3.Aftre giving command press enter.
1.Such window will appear, here enter our user name & press enter.
1.After giving our user name ,give our path where sbc9302tools are copied i.e.on Desktop.2.Then press enter. & press y For installing our workspace again press enter.3.All process shown below,
1.When our workspace is installed at home then it shows message given below,
2.Our workspace will be installed at home as sbc9302
1.Firstly open console terminal.2.Give command su press enter & give our root password then press enter.3.After give command vim /etc/xinetd.d/tftp/ & press enter.4.All process given below,
1.Such window will appear.2.For insert word press shift+i.2.Then set path such as -c s /home /maahi(user name)/maahi/tftpboot/ & press esc key.3.Finaly press :wq & press enter. Our path will be set .((:wq ) is saving command).
1.Firstly open folder which is on Desktop as sbc9302.2.Open Pdf file i.e. user manual_9302.3.Then find path & select these path i.e. Copy these path as shown below,
1.Firstly open home & go to view< Select show hidden file.2.Double click on bash_profile i.e.open bash_profile
1.Here set path which is copied from sbc9302 tools user manual . From desktop. 2. Path is shown below,
Paste path here
1.Open console terminal ,then give command su press enter.2.Give our root password & press enter.3.Give command minicom s & press enter.4. All process shown below,
1.Such window will appear.2.Then select serial port setup& press enter.3.All process shown below.
1.Such window will appear, here make all setting like picture such as given below,2.When we press letter i.e. A to G we can edit these setting.3.We need only change in serial Device,Boud rate, Hardware flow control.
1.After making of all setting save these setting permantly select save setup as dfl & press enter.2.After that select "exit & press enter.3.Our minicom will be initialize.
1.Such window will appear .2.Here we can connect our SBC9302 Project board.