SAT Patrol Series 2000 is the new Point ID

perimeter intrusion detection system for the protection

of soft metal fences and semi-rigid panels.

Designed and developed by SAT Patrol LAB Security,

Series 2000 are evolution of sensitive boxes system

which has been successfully employed for over 5 years

in protecting thousands of kilometers of fencing in

very strategic fields such as government, military, oil &

gas, airports and seaports.

As sensitive boxes system, Series 2000 deploys

piezodynamic sensors which detect cut, climb and

breakthrough attempts in a very effective way. As a

matter of fact, the piezodynamic technology, designed

and patented by SAT Patrol Security, offers superior

probability of detection (POD) and very low nuisance

alarm rate (NAR); this means very high tolerance

towards environmental nuisances such as adverse

weather conditions (heavy rain and strong wind),

climbing vegetation and man-made factors (nearby

heavy traffic roads and railways).

Sensitive boxes system allows you to precisely locate

the point under alarm: each sensor is individually

identified and integrates a sophisticated analysis unit

which independently processes the signals detected and

then sends the different alarm reports to a centralized

control unit which can manage up to 500 detectors.

The state-of-the-art technology developed for sensitive

boxes system makes the latter one of the most reliable

PIDS currently on the market.

SP 2000 Series

Point ID: Each SAT Patrol sensor is individually identified to allow you to precisely locate the point

under alarm: an alarm zone (logical line) can be also composed of a single sensor.

Up to 500 sensors: managed on 2 communication buses to protect a perimeter up to 1500 meters with a

single control unit (if the sensors are installed every 3 meters). This feature remarkably simplifies the wiring

infrastructure, especially in big sites.

Self-test and self-diagnosis: A self-

test function is implemented in each sensor

and checks the status of both the electronic

part and the piezodynamic transducer. Self-

diagnosis functions are performed by the

control unit that continuously monitors the

bus and the sensor operating parameters: this

allows you to discriminate possible degrading

factors before a failure may occur.

Anti-removal electronic device: It

detects the removal of the SAT Patrol sensor

from the fence. During the installation phase,

it signals, via software, the wrong fixing of

the sensor.

Magnetic and thermal tamper device: It identifies and signals the attempts of tampering the sensor by

exposing it to electromagnetic fields or extreme temperatures.

Simple and quick installation: SAT Patrol sensitive sensors boxes are provided in prewired strings for an

easy and quick installation. Sensor automatic identification and sorting: Upon the first configuration of the system, the control unit

automatically identifies all the sensors that are linked to the bus and, using an algorithm patented by SAT, sorts

them according to their physical location (from closest to furthest).

Distribution on logical lines. The control unit automatically distributes the sensors on 64 alarm logical

lines. After that, it is possible to manually

modify the length of each logical line to

adapt it to the configuration of the perimeter.

Calibration and configuration per

single unit or per logical line: Each SAT

Patrol sensor can be calibrated and

configured together with the others of the

same line or individually to obtain the best

calibration even on heterogeneous fence

panels. During the individual calibration, the

real time analog signal is available on the

service software (3D chart).

Capability of managing signals

from 3rd party devices, such as infrared or

microwave barriers, by means of a special interface module. The module can be placed anywhere along the bus.

Comprehensive signal analysis. For each sensor it is possible to discriminate the following signals: cut,

climb, breakthrough, sporadic cut, removal attempt, thermal tamper, link quality, self-diagnosis, absorption and

temperature.

Technical Specifications

Control Unit: • Power supply:120~ 230 V

• Current: 1.2 A (max)

• Buffer battery: 2 x 12 V / 7,2 Ah

• Operating temperature (electronic components): -25 ÷ +70 °C

• Cabinet material: polyester, IP65 rating

• Cabinet dimensions: 100 x 150 x 80 mm

• Weight of the preassembled cabinet: approx. 13 Kg (including batteries)

• Digital inputs: 8 optoinsulated inputs, service software configurable

• Relay NC outputs (1 A):

General Alarm

General Tamper

Watchdog

Sensor Failure

Bus Link Loss

• SPDT relay outputs:

Discharged or damaged battery

Power supply from mains or battery

• OC outputs: 3 configurable outputs

• Configurable external relay outputs: up to 128 by means of expansion boards (optional) • USB port for service activity

Ethernet port for service activity or for SAT Patrol Logger / SAT MAP

• Calibrations and configurations: through service software for Microsoft Windows

• CPU: 32 bit

• Digital memory: more than 20.000 events

Sensor: • Dimensions: 90 x 53 mm (Ø x H)

• Operating temperature: -40 ÷ +85 °C

• Relative humidity: 0-100%

• Case Material: glass fiber reinforced polyamide, sealed with polyurethane resin, UV, oil and scratch resistant

• Coverage area: max 3 x 3 m (maximum dimension of the fence panel with sensor in mid-position)

• Colour: black

Sensor-string: • 50 series 2000 sensors with 3-metre spacing, black color

Connection cable: • Diameter: 8 mm

• Operating temperature: -40 ÷ +80 °C • Jacket: mat polyurethane, UV, oil and scratch resistant • Color: black

© 2014 SAT Patrol Co.

IRAN, Kermanshah City, Mostafa Emami Av. Kowsar St. No 336 tel. +988318226645- +988318226643-+988318253518 - fax +988318234010

www.satpatrol.com – sales@satpatrol.com