sapido

ww

w

.sapidotech . comQuick Installation Guide (V2.1)Quick Installation Guide (V2.1)

Applicable Model:RB-1602/R B-1632

RB-1132V2/MB-1132/M B-1112

D e f a u l t I P :1 9 2 . 1 6 8 . 1 . 1 ( R o u t e r M o d e )1 9 2 . 1 6 8 . 1 . 2 5 4 ( A P M o d e )1 9 2 . 1 6 8 . 1 . 2 5 4 ( W i F i A P M o d e )D e f a u l t Username：a d m i nD e f a u l t P a s s w o r d：a d m i n

Important Information

※Press the Reset button to set the router back to factory settings while forgetting the users name and password.※We suggest using WiMAX modem with a USB extended cable for the best performance.※When you switch the mode, please unplug power adapter and plug in again.

Frequently Asked QuestionsFAQ 23-24

1-56-7

88- 9

10-1112-1314-1516-1718-1920-21

2223

Configuration

Basics

Table of Contents

Getting to Know your RouterInstalling the Router

Logging into your RouterConnecting this Router to a Cable/DSL ModemConnecting this Router to a 3G/4G modemConnecting this Router to a SmartphoneConnecting this Router to a WiMAX modemConnecting to an Existing WiFi Network(Public WiFi)Connecting to an Existing Wired IP RouterConnecting to Another WiFi network to extend the SignalOptional Firmware UpgradeResetting Your Router back to Factory Settings

1

Mini USB Power Connector

WAN/LAN PortThis connects to your DSL/Cable Modem.

LAN PortUse this port to connect to your computer.

Mode Switch

Getting to Know your Router1 Router, 1 Power Adapter, 1 Antenna (Detachable),1 Quick Installation Guide

RB-1602

WAN/LAN Indicator

LAN Indicator

Wireless/WPS IndicatorWhen the light is green, wireless is active. When this light starts to flash and turns to reddish orange, WPS setup is in progress

ResetBack to factory setting.

WPS Button

Status IndicatorWhen the green light is on, system is ready to work. Whenthe light is blinking means reset or firmware update is in progress.

See the WPS one-button setup section for additional information.

2RB-1632

Getting to Know your Router1 Router, 1 Power Adapter, 1 Quick Installation Guide

WAN/LAN Port This connects to your DSL/Cable Modem.


Mini USBPower Connector

Mode Switch

USB portUse this port to connect a 3G/4G/WiMAX modem orsmartphone

Status IndicatorWhen the green light is on, system is ready to work. When the light is blinking means reset or firmware update is in progress.

WPS ButtonSee the WPS one-button setup section for additional information.

WAN/LAN Indicator

LAN Indicator


When the light is green, wireless is active. When this light starts to flash and turns to reddish orange, WPS setup is in progress.

Wireless/WPS Indicator

3RB-1132V2

Getting to Know your Router1 Router, 1 AC plug,1 Power Adapter, 1 Quick Installation Guide

Mini USBPower ConnectorWireless/WPS Indicator

LAN IndicatorWAN/LAN Indicator

Status IndicatorWhen the green light is on,system is ready to work. When the light is blinking means reset or firmware update is in progress.

Power IndicatorWhen the light is green, the device is receiving power.

USB portUse this port to connect a 3G/4G/WiMAX modem or smartphone.


LAN/WAN PortThis connects to your DSL/Cable Modem.



Mode Switch

AC Plug

When the light is green, wirelessis active. When this light starts toflash and turns to reddish orange,WPS setup is in progress.

4MB-1132Getting to Know your Router1 Router, 2 Li Batteries,1 Power Adapter, 1 Quick Installation Guide

PowerConnector


LAN/WAN PortThis connects to your DSL/Cable Modem or computer.

USB PortUse this port to connect a 3G/4G/WiMAX modem or smartphone.

USB Indicator

Wireless/WPS IndicatorWhen the light is green, wirelessis active. When this light starts to flash and turns to reddish orange, WPS setup is in progress.

Power Indicator

Status Indicator

LAN/WAN Indicator

Power Switch


When the green light is on, system is ready to work. When the light is blinking meansreset or firmware update is in progress.

When the light is green, the device is receiving power.


5MB-1112

PowerConnector


WPS Button

LAN/WAN PortThis connects to your DSL/Cable Modem or computer.

USB Portonly for power output

Power Switch

Getting to Know your Router1 Router, 2 Li Batteries, 1 Power Adapter,1 Quick Installation Guide

SIM Slot

3.5G Indicator

Wireless/WPS IndicatorWhen the light is green, wirelessis active. When this light starts toflash and turns to reddish orange,WPS setup is in progress.

Power Indicator

Status Indicator

LAN/WAN Indicator


When the green light is on, system is ready to work. When the light is blinking means resetor firmware update is in progress.

When the light is green, the device is receiving power.

See the WPS one-button setup section for additional information.

6Installing the RouterDSL/Cable Modem:Applicable Model : RB-1602/RB-1632/RB-1132V21. Use Ethernet cable to connect the modem and the WAN port of SAPIDO router.2. Use Ethernet cable to connect PC and LAN port of the SAPIDO router.

Applicable Model : MB-1132/MB-11121. Use Ethernet cable to connect the modem and the LAN/WAN port of SAPIDO router.2. Connect PC and the SAPIDO router wirelessly.

3G/4G/WiMAX modem:1.Connect the 3G/4G/WiMAX modem to the SAPIDO router using a USB cable.2.Use Ethernet cable to connect PC and LAN port of the SAPIDO router.

Smartphone:1.Use a USB cable to connect the smartphone to the SAPIDO router. See the smartphone section for additional information.2.Use Ethernet cable to connect PC and LAN port of the SAPIDO router.

Ethernet Cable

Ethernet Cable

Ethernet Cable

Wired xDSL/Fiber/Cable Modem Ethernet Cable

Ethernet Cable

Wired xDSL/Fiber/Cable Modem

Ethernet Cable

Ethernet Cable

Plug intoUSB port

Plug into USB port

Ethernet Cable

Ethernet Cable

Plug into USB port

Plug into USB port

7Connecting to an Existing WiFi Network (Public WiFi):1.No physical connection is required to receive the signal.2.Use Ethernet cable to connect PC and LAN port of the SAPIDO router.

WiFi Hotspot

Wireless Modem

Ethernet Cable

Ethernet Cable

Connecting to Another WiFi network to extend the Signal:1.No physical connection is required to receive the signal.2.Use Ethernet cable to connect PC and LAN port of the SAPIDO router.

Wireless Router

Ethernet Cable

Ethernet Cable

Connecting to an Existing wired IP router:1.Use an Ethernet cable to connect the WAN port of the SAPIDO router to the existing wired IP router.2.Use Ethernet cable to connect LAN port of the SAPIDO router and the computer.

Ethernet Cable

Ethernet Cable

Ethernet CableWired IP Router

Ethernet Cable

8Configuration

4. Select “WAN Interface” is Ethernet Port. Select your “WAN Access Type” according to your Internet source, and enter the username/password. Then, you can start to setup the wireless encryption.

1. Open IE browser, type IP 192.168.1.1(P.1), or open “My Network Place”, and click SAPIDO_RB-1632(P2).

It can be configured without Internet.

Enter the router IP address (defaults below) into your browser and hit “Enter”.Router Mode : 192.168.1.1Access Point & WiFi Access Point Mode : 192.168.1.254Enter Login Information (default below) and click “Login”.Username : adminPassword : admin

(P1)

192.168.1.1

3. Select “One Button Setup”(P4) on the left menu.

2. Fill in default Username and Password to login(P3).

(P3)

adminadmin

(P4) (P2

SAPIDO_RB-1632

Switch the operation mode to “R”.

5. After the setting is finished, you should see a “change successful” page with countdown. When the countdown is completed, your wireless network and security will be active, and you should be able to login immediately with the new password. However, if an error message shows up, please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.

Logging Into Your Router :

Connecting this Router to a Cable/DSL Modem :

9

SAPIDO_RB-1632

‧Dynamic IP, which is the default, is the most common setting, and will work with most cable modems. Try this first!‧Unfortunately, WAN Access Type varies by company,so if this does not work please contact your Internet service provider and ask them what “WAN Access Type”settings to use for your modem. For Example,DSL users may need to use PPPoE or PPTP, which requires your unique DSL username and password.

This is the name of your wireless network. Change it tosomething that will be easy for you to identify (e.g. “Smith Family”).

Change the “Encryption” dropdown to your preferred form ofsecurity. If you are not sure, choose WPA2(the most commonlyused) . This sets the password that will be neededto log intoyour wireless network. Enter any wireless network passwordthat is at least 8 characters.

Choose “Ethernet Port”.

Click “Finish” to complete Setup.

Wired xDSL/Fiber/Cable modem

10It can be configured without Internet.

(P4)

4. Select “WAN Interface” is 3.5G USB dongle, and starts the setup and wireless encryption.

5. After the setting is finished, you should see a “change successful” page with countdown. When the countdown is completed, your wireless network and security will be active,and you should be able to login immediately with the new password. However, if an error message shows up, please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.


(P1)

192.168.1.1


(P3)

adminadmin


※The quality of wireless signal depends on strength of 3G/4G signal.※Please find update support list at SAPIDO official website.

(P2)

SAPIDO_RB-1632

Connecting this Router to a 3G/4G modem :

(RB-1602 is not supported)


11

Choose “3.5G USB dongle”.


Change the “Encryption” dropdown to your preferred form of security. If you are not sure, choose WPA2 (the most commonly used). This sets the password that will be needed to log into your wireless network. Enter any wireless network password that is at least 8 characters.

input SIM PIN/ APN/ User Name/ Password/ Phone Number required by your ISP. f you are not sure about local ISP3.5G system or APN setting information, please contact your ISP.

"Auto Switch" is recommended to avoid any disconnection when 3G/ 3.5G signal is unavailable.


3G/4G modem

12

4. Select “WAN Interface” is 3.5G USB dongle, and starts the setup and wireless encryption.

5. After the setting is finished, you should see a“change successful”page with countdown. When the countdown is completed,your wireless network and security will be active,and you should be able to login immediately with the new password. However, if an error message shows up, please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.


Smartphone Set-up : (Do not need to enter into GUI setting page for set-up.)Enable the “Internet Tethering”, and it’s ready to share Internet access.※If you’re using an iPhone, please change the “Auto-lock” to never, and connect it to SAPIDO router after enable the Internet Tethering feature.GUI Set-up :

(P3)

adminadmin



(P1)

192.168.1.1

(P2)SAPIDO_RB-1632


(P4)


Brand Apple HTC/ASUS/Samsung HTC Blackberry Nokia Samsung

Support OS OS Google Android Windows Mobile Blackberry Symbian BadaSmartphone

Set-up

GUI Set-up

i

Connecting this Router to a Smartphone :

※Please find update support list at SAPIDO official website.

(RB-1602/MB-1112 are not supported)

13

Choose “3.5G USB dongle”.


"Auto Switch" is recommended to avoid any disconnection when 3G/ 3.5G signal is unavailable.

According to your smartphone system, select your service as Nokia, Blackberry, etc.



Smartphone

14

4. Select “WAN Interface” is WiMAX, and starts the setup and wireless encryption.

5. After the setting is finished, you should see a “change successful”page with countdown When the countdown is completed, your wireless network and security will be active, and you should be able to login immediately with the new password.However,if an error message shows up,please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.



adminadmin

(P3)


(P1)

192.168.1.1

(P2)SAPIDO_RB-1632


※We suggest using WiMAX modem with a USB extended cable for the best performance.※Please find update support list at SAPIDO official website.


(P4)

Connecting this Router to a WiMAX modem :(RB-1602/MB-1112 are not supported)

15

WiMAX modem

SAPIDO_RB-1632

Select Operator and enter account info.

Choose “WiMAX”.




16

4. Select “WAN Interface” is Wireless. Choose the network you would like to connect, then select the encryption type and fill the encryption key. Select your “WAN Access Type” according to your Internet source, and starts to setup the wireless encryption.

5. After the setting is finished, you should see a “change successful” page with countdown. When the countdown is completed, your wireless network and security will be active,and you should be able to login immediately with the new password. However,if an error message shows up,please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.



adminadmin

(P3)


(P1)

192.168.1.1

(P2)SAPIDO_RB-1632


(P4)

Connecting to an Existing WiFi Network (Public WiFi) :


17


Select the network you would like to connect.

Choose “Wireless”.

This is the name of your wireless network. Change it to something that will be easy for you to identify (e.g. “Smith Family”).

If the wireless is from Public WiFi, please select Dynamic IP. If the wireless is from wifi modem, please select the WAN type and enter account information by your ISP.

Select the encryption type of upper network you connect and fill in its encryption key.


Public WiFi/Wireless modem

18

4.Select your encryption type and enter the password.5. After the setting is finished, you should see a“change successful” page with countdown.When the countdown is completed, your wireless network and security will be active,and you should be able to login immediately with the new password. However, if an error message shows up, please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.

3.Click “One Button Setup”(P4) on the left menu.


adminadmin

(P3)

If ADSL/Fiber/Cable is connected to a wired router, connect the wired router to your SAPIDOrouter. Then, you can turn wired Internet to wireless and share Internet to multiple devices suchas in hotel.


(P1)

192.168.1.1

(P2)SAPIDO_RB-1632

Switch the operation mode to “A”.

(P4)

Connecting this Router to a wired IP router :(MB-1132/MB-1112 are not supported)


19Have a wired IP router




Choose your time zone.

Enter a new router password to replace the default one to log into the router (this is different from your wireless password).

20

1. Press the WPS button on the 11N product that you would like to connect till the WPS LED starts to flash.2. Press the WPS button on the SAPIDO router till the WIRELESS/WPS LED turns to reddish orange.Then the WiFi AP setup is done.


(P1)

192.168.1.1

3. Click “One Button Setup”(P4) on the left menu.


adminadmin

(P3)

If the network you would like to connect is an 11N product with WPS feature, you may complete the WiFi AP setup with the WPS button.

Via WPS Button

4. Choose the network you would like to connect. Select the encryption type and fill the encryption key, then starts to setup the wireless encryption.

(P2)

SAPIDO_RB-1632

If ADSL/Fiber/Cable is connected to a wireless router, connect the wireless router to your SAPIDO router, then you can extend wireless signals and share Internet to multiple devices.

Via Program

5. After the setting is finished, you should see a “change successful”page with countdown. When the countdown is completed,your wireless network and security will be active,and you should be able to login immediately with the new password. However, if an error message shows up , please refresh the page and it will go back to the entering page. Afterwards, you can access Internet.

(P4)

Connecting to another WiFi network to extend the Signal :

Switch the operation mode to “W”.(MB-1132/MB-1112 are not supported)


21

Select the network you would like to connect.

Select the encryption type of upper network you connect and fill in its encryption key.




Have a wireless router

22

Please visit SAPIDO website www.sapidotech.com and upgrade the firmware toachieve optimal performance.

1.Log into your router and check the “Firmware Version” on the home screen.

2.Go to the SAPIDO website at service & support download center.

3.Choose your model number in the Firmware section and click “Go”.

4.Check to see if the most recent version is higher than yours. If not, then no updates

are available. If a newer version is available, download the appropriate file.

5.Login to the SAPIDO router.

6.Select “System Management” → “Firmware Upgrade”.

7.Click “Browser” and point to the new firmware file just downloaded. Click “Upload”

to upgrade the firmware. Note: Do not change pages or run other programs before

the router’s reboot is completed, to avoid interrupting the upgrade.

8.Press the Reset button on the back panel of the router to complete the firmware upgrade.

9.Press F5 or clean cookies, and then login.

Optional Firmware Upgrade :

23

Frequently Asked Questions1. Why can’t I login SAPIDO router? (1) Please make sure your connection is right. Your computer should connect to the LAN port of SAPIDO router. (2) Confirm the browser you used is Microsoft Internet Explorer, and type the IP 192.168.1.1. Enter the default username and password: admin. If it is wrong, please reset your router back to factory settings.2. How to encrypt the SAPIDO router? Login SAPIDO Router and choose “One Button Setup”. Select your encryption type in Wireless Setup or Extended Wireless Setup of the bottom. WPA2 is recommended. Please enter at least 8 characters/numbers.If your computer is not supported WPA2, you can select WEP and enter 10 numbers. Then, click “Finish” to complete setup.

Note : This will erase all of your configuration settings.To restore the router to factory default settings. Please do the following.1.Power on SAPIDO router, and wait till the Wireless/WPS light is lit.2.Press the reset button on the back of the router with a pencil or paper clip, and hold it down for 10 seconds, until the status light blinks 3-4 times, then release.3.You should see the Wireless/WPS light flash. Once it stays lit (and green), the router is finished being reset.

Resetting Your Router back to Factory Settings :

24

3. How to connecting your computer to the wireless network? (under Windows 7 OS) (1) In Windows 7, click on the wireless network icon on the bottom right of your desktop, and choose your wireless network name from the list.e setup. (2) Click “Connect”. (3) If you have setup a security key, it will prompt for your pass code. Enter your pass code, and then click “OK”. Alternatively, you can press the WPS button on the side of the router to send the password automatically (instead of typing it in). (4) After a few seconds, you should be connected to the network.

Troubleshooting: User manual and Frequently Asked Questions are available for SAPIDO router. Please visit SAPIDO website www.sapidotech.com.

ww

w

.sapidotech . comADD:383, Sec. 2, Minsheng Rd.,West Central District, Tainan City700, Taiwan

E-mai l: [email protected]

SAPIDO Technology Inc.

Documents

sapido