SANUS VMPL50B Tilting Wall Mount Manual

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USACustomer Service: 1-800-359-5520 • [email protected] • www.sanus.com

(6901-100134 <04>)

Thank you for choosing the Sanus Systems VMPL50 monitor mount. The VMPL50 is designed to support flat-panel monitors 30 - 50 inches (76 - 127 cm), and weighing no more than 59 kg (130 lbs.). The VMPL50 is adjustable, allowing ±12˚ of tilt.

Do not use this product for any purpose not explicitly specified by Sanus Systems. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Sanus Systems Customer Service or call a qualified contractor. Sanus Systems is not liable for damage or injury caused by incorrect mounting, assembly, or use.

CauTION

VMPL50

OPT

OPTHardware and procedures for multiple mounting configurations are included. When you see this symbol, choose the correct configuration to suit your needs. Not all hardware included will be used.

002153.epsVMPL50 / FPM50 - full assembly

6901-100134 <04>

Supplied Parts and Hardware

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Systems Customer Service. Never use damaged parts!

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

WaRNING

3/16 in.1/2 in.

Avoid potential personal injuries and property damage! The monitor must be 30 - 50 inches (76 - 127 cm), and must weigh no more than 59 kg (130 lbs.). The wall must be capable of supporting up to five times the weight of the monitor and mount combined. If you have any doubts about the ability of the wall to support the monitor, contact Sanus Systems Customer Service, or a qualified contractor. This product is not designed for use in metal stud walls!

CauTION

6901-100134 <04>

002154.epsVMPL50 / FPM50 - wall plate and brackets

M4 x 12 mm M5 x 12mm M6 x 12 mm M8 x 16 mm

M4 x 30mm M5 x 30mm M6 x 35mm M8 x 40mm

M4 M5 M6 M8

M4 / M5 M6 / M8 M4 / M5 M6 / M8

5/16 in.

1/4-20 x 0.875 in.

001897.eps VMPL Parts

[23] x 2

[10] x 4[09] x 4[08] x 4[07] x 4

[06] x 6[05] x 6[04] x 6

[02] x 1

[03] x 1[01] x 1

[14] x 4[13] x 4[12] x 4[11] x 4

[18] x 4[17] x 4[16] x 4[15] x 4

[22] x 4[21] x 8[20] x 4[19] x 4

[24] x 1

6901-100134 <04>

1-1

002162.epsVMPL50 / FPM50 - Mount to wood stud




3/16 in.

[01]

[05][04]

>30.5 cm (12 in.)

Do not overtighten the lag bolts! Tighten the lag bolts [04] only until the washers [05] are pulled against the wall plate [01].

CauTION

6901-100134 <04>

002163.epsVMPL50 / FPM50 - Mount to concrete

1-2

1/2 in.


[05][04]

[01]

[06]


>15 cm (6 in.)

>64 mm (2.5 in.)

Avoid potential personal injuries or property damage! Never drill into the mortar between the blocks. Be sure the plastic anchors [06] seat flush with the blocks.

CauTION

6x

Do not overtighten the lag bolts! Tighten the lag bolts [04] only until the washers [05] are pulled against the wall plate [01].

CauTION

6901-100134 <04>

2-1

002155.epsVMPL50 / FPM50 - Back of monitor


[03]

[02]

[07], [08], [09], [10][15], [16],

[17], [18][21], [22]

Use washer [21] with M4 or M5 hardware. Use washer [22] with M6 or M8 hardware.

6901-100134 <04>

2-2



[03]

[02]

[07], [08], [09], [10]

[15], [16], [17], [18]

[21], [22]

[21][19], [20]

OPT

OPT

Use washer [21] with M4 or M5 hardware. Use washer [22] with M6 or M8 hardware.

Use washer [21] with M4 or M5 hardware only.OPT

OPT

6901-100134 <04>

3

002164.epsVMPL50 / FPM50-Mount brackets to wall plate


[24]

2x

[23]

Avoid potential personal injuries or property damage! Be sure to install the safety bolts [23]. Periodic tightening may be required.

CauTION

HEaVY! You will need assistance with this step.

6901-100134 <04>

4


[A]

Adjust up / down pitch. Use the tension knob [A] to adjust the pitch tension.OPT

OPT

6901-100134 <04>

CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, “CSAV”), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Documents

SANUS VMPL50B Tilting Wall Mount Manual