Samsung Ua40d6000sjxxz Sm

7/24/2019 Samsung Ua40d6000sjxxz Sm

1/94


2/94


3/94


4/94

1-1

1. Precautions

1. Precautions

1-1. Safety Precautions

Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as

electrical shock.

1-1-1. WarningsFor continued safety, do not attempt to modify the circuit board.1.

Disconnect the AC power and DC power jack before servicing.2.

1-1-2. Servicing the LED TV

When servicing the LED TV, Disconnect the AC line cord from the AC outlet.1.

It is essential that service technicians have an accurate voltage meter available at all times.2.

Check the calibration of this meter periodically.

1-1-3. Fire and Shock Hazard

Before returning the LED TV to the user, perform the following safety checks:

Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the1.chassis and other metal parts in the LED TV.

Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and2.

compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc.

Leakage Current Hot Check (Figure 1-1):3.

WARNING: Do not use an isolation transformer during this test.Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI

C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the units AC switch4.

rst in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit,

etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts.

The current measured should not exceed 0.5 milliamp.Reverse the power-plug prongs in the AC outlet and repeat the test.

1-1-4. Product Safety Notices

Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visualinspection. The protection they give may not be obtained by replacing them with components rated for higher voltage,

wattage, etc. Parts that have special safety characteristics are identied by on schematics and parts lists. A substitute

replacement that does not have the same safety characteristics as the recommended replacement part might create

shock, re and/or other hazards. Product safety is under review continuously and new instructions are issued whenever

appropriate.

DEVICEUNDER

TEST

(READING SHOULD)

NOT BE ABOVE 0.5mA

LEAKAGE

CURRENT

TESTER

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

*ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)EARTH

GROUNDFigure 1-1. Leakage Current Test Circuit


5/94

1-2

1. Precautions

1-2. Servicing PrecautionsWARNING: An electrolytic capacitor installed with the wrong polarity might explode.

Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of

this manual.

Note: If unforeseen circumstances create conict between the following servicing precautions and any of the

safety precautions, always follow the safety precautions.

1-2-1 General Servicing PrecautionsAlways unplug the units AC power cord from the AC power source and disconnect the DC Power Jack before1.

attempting to:

(a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a testcomponent in parallel with an electrolytic capacitor.

Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes2.used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such

elements to their original position.

After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that3.the area around the serviced part has not been damaged.

Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels,4.input terminals and earphone jacks).

Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON.5.Connect an insulation resistance meter (500 V) to theblades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be

greater than 1 megohm.

Always connect a test instruments ground lead to the instrument chassis ground before connecting the positive lead;6.

always remove the instruments ground lead last.

1-3. Electrostatically Sensitive Devices (ESD) Precautions

Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly

called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some eld-effect

transistors. The following techniques will reduce the incidence of component damage caused by static electricity.

Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your1.

body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard,be sure to remove the wrist strap before applying power to the LED TV.

After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent2.

accumulation of an electrostatic charge.

Do not use freon-propelled chemicals. These can generate electrical charges sufcient to damage ESDs.3.

Use only a grounded-tip soldering iron to solder or desolder ESDs.4.

Use only an anti-static solder removal device. Some solder removal devices not classied as anti-static can generate5.

electrical charges sufcient to damage ESDs.

Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs6.

are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductivematerials.

Immediately before removing the protective material from the leads of a replacement ESD, touch the protective7.material to the chassis or circuit assembly into which the device will be installed.

Caution:Be sure no power is applied to the chassis or circuit and observe all other safety precautions.

Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together,8.

or lifting your foot from a carpeted oor can generate enough static electricity to damage an ESD.


6/94

1-3

1. Precautions

1-4. Installation Precautions

For safety reasons, more than a people are required for carrying the product.1.

Keep the power cord away from any heat emitting devices, as a melted covering may cause re or electric shock.2.

Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal3.

temperature may cause re.

Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed4.

to moisture. Otherwise, it may cause a re or electric shock.

Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check5.

the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause re or electric

shock.

Keep the antenna far away from any high-voltage cables and install it rmly. Contact with the highvoltage cable or the6.

antenna falling over may cause re or electric shock.

When installing the product, leave enough space (0.4m) between the product and the wall for ventilation purposes.7.

A rise in temperature within the product may cause re.


7/94

2-1

2. Product specications


2-1. Specications Information

2-1-1. Model Comparison

Model UD6400 UD6600

Front view All

Detail view

All

All

Front Color All Clear + Charcoal Black Clear + Charcoal Balck

Dimensions

W x D x H

(mm)

40"Without Stnand 929.5 x 29.9 x 545.3 923.5 x 29.9 x 539.6

With Stand 929.5 x 255 x 606.4 923.5 x 241.3 x 617.4

46" Without Stnand 1064.9 x 29.9 x 621.7 1058.9 x 29.9 x 616With Stand 1064.9 x 275 x 682.8 1058.9 x 276.6 x 698.8

55"Without Stnand 1255.3 x 29.9 x 728.3 1258.8 x 29.9 x 731.7

With Stand 1255.3 x 275 x 808.4 1258.8 x 275 x 791.4

Weight

(kg)

40"Without Stnand 9.91 9.9

With Stand 12.43 11.3

46"Without Stnand 12 12.56


55"Without Stnand 17.21 17.3


Panel Type All Super-Clear Super-Clear

Internal

MemoryAll 128 Mbtye 128 Mbtye

DDR All 512 Mbtye 768 Mbtye

Feature AllMedia Play(USB/DLNA)

3D, SMART HUB

Media Play(USB/DLNA)

Wi-Fi(Built-in), 3D, SMART HUB


8/94

2-2


2-1-2. Feature & Specications

Model UA40D6400 / UA40D6600

Feature

Digital-TV, RF, 4-HDMI, 1-Component, 1-A/V, 3-USB2.0(Media Play), D-SUB , LAN

Respons time : 6.5 ms

Dynamic contrast , Super-PVA

PIP(in HDMI 1, 2, 3, 4, Component 1, PC Mode and Sub picture is available only in TV mode(DTV/ATV))

Dolby Digital+, SRS theater

Specications

Item Description

LCD Panel 40 inch HD 120Hz

Scanning Frequency Horizontal : 135.6 KHz(TYP) I Vertical : 120 Hz(TYP)

Display Colors 1.07G Colors

Maximum resolution Horizontal : 1920 Pixels I Vertical : 1080 Pixels

Input Signal Analog 0.7 Vp-p 5% positive at 75 , internally terminated

Input Sync Signal H/V Separate, TTL, P. or N.

Maximum Pixel Clock rate 80 MHz

Active Display (Horizontal/Vertical) 885.6 (H) x 498.15 (V) mm

AC power voltage & Frequency AC 220-240 V 50/60 Hz

Power Consumption 130 W (Under 0.1 W, Stand by)

Dimensions Set(W x D x H)

6400929.5 (W) x 255 (D) x 606.4 (H) mm_with stand

929.5 (W) x 29.9 (D) x 545.3 (H) mm_without stand

6600923.5 (W) x 241.3 (D) x 617.4 (H) mm_with stand


6400 12.43 kg_with stand / 9.91 kg_without stand


TV System Tuning Frequency Synthesize (Refer to detailed Frequency Table)

System PAL , SECAM , NT4.43

Sound BK , DK , NICAM , MPEG1

Environmental Considerations Operating Temperature : 50F ~ 104F (10C ~ 40C)Operating Humidity : 10% ~ 80%, non-condensing

Storage temperature : -13F ~ 113F (-25C ~ 45C)

Storage Humidity : 5% ~ 95%, non-condensing

Audio spec. - MAX Internal speaker Out : Right/Left(10 W)- BASS Control Range : -10dB ~ +10dB

- TREBLE Control Range : -10dB ~ +10dB

- Output Frequency : RF : 20 Hz ~ 15.4 kHz

AV/Componet / HDMI : 20 Hz ~ 20 kHz

Note:3D,Media Bridge, AllShare, Internet TV, Built-in Wi-Fi(6600 Only), Full Browser, Bluetooth


9/94

2-3



Feature






Specications

Item Description











Dimensions Set

(W x D x H)6400



66001058.9 (W) x 276.6 (D) x 698.8 (H) mm_with stand

1058.9 (W) x 29.9 (D) x 616 (H) mm_without stand

6400 16.24 kg_with stand / 12 kg_without stand














10/94

2-4



Feature






Specications

Item Description











Dimensions Set

(W x D x H)6400





Weight (Set) 6400 21.89 kg_with stand / 17.21 kg_without stand














11/94

2-5


2-1-3. Spec Comparison to the Old Models

Model UD6T UC6U

Design

UD6400 UD6600

Display Type LED TV LED TV

Built-in Tuner O O

Resolution 1920 x 1080 1920 x 1080

LCD Panel TFT LCD Panel 100Hz TFT LCD Panel 100Hz

Screen Size 40"/46"/55" 32"/37"/40"/46"/55"

Picture ratio 16:9 16:9

3D O X

Built-in WiFi X X

Light Sensor O O

Picture Enhancer DNIe+(FBE3) DNIe+(FBE3)

Equalizer 5 Band 5 Band

Auto Motion Plus 120Hz YES YES

Surround Sound 2Way SRS TruSurround Dolby Digital 2Way SRS TruSurround Dolby Digital

Speaker Output40"/46" : 10W + 10W

55" : 15W + 15W32"/37"/40"/46" : 10W + 10W

55" : 15W + 15W

Energy Saving O O

PIP O O

Game mode O O

Anynet+ O O

Antena DTV 1 (Cable/Air) DTV 1 (Cable/Air)


12/94

2-6


2-2. Detail Factory Option

If you replace the main board with new one, please change the factory option as well.

The options you must change are "Type" and "Front Color".

2-2-1. UD6*00

Model Name UA40D6*00 UA46D6*00 UA55D6*00

Panel

Vendor CMI AUO AMLCD(LCM)

CODE BN07-00997A BN07-00984A BN95-00451A

SPEC LD400CSC-C1 LD460CSB-A1 LTJ550HW01-V

SMPS

Vendor SEM SEM SEM

CODE BN44-00427A BN44-00427A BN44-00428A

SPEC PD46A1D_BHS PD46B2_BSM PD55B2_BSM

1 Factory Reset -

2 Type 40P1UF6E 46L1UF6E 55A1UF6E

3 Local set

AD_AU : UA**D6000*MXXY

AD_NZ : UA**D6000*MXRD

AD_SINGAPOL : UA**D6000*MXXSEA_THAI : UE**D6000*RXXT

EA_MAL : UA**D6000*RXXM

EA_PHI : UA**D6000*RXXPEA_S_AFRICA " UA**D6000*RXXA

EA_AFRICA : UA**D6000*RXSW / UA**D6000*RXSJ / UA**D6000*RXKE

UA**D6000*RSHA / UA**D6000*RSGA

EA_EGYPT : UA**D6000*R*MN / UA**D6000*R*ECEA_RIBYA : UA**D6000*RSSK

EA_SAUDI : UA**D6000*RXUM

EA_E_ASIA : UA**D6000*RXTW

ED_VIET : UA**D6000*MXXVED_INA : UA**D6000*MXHC / UA**D6000SMXXD

ED_IRAN : UA**D6000*MSHD / UA**D6000*MXHC

ED_ISRAEL : UA**D6000*MXSQ

EU_AFRICA : UA**D6000*WXSH / UA**D6000*W*ABEU_MOROCO : UA**D6000*WXMV

4 Model UD6400/UD6600 UD6400/UD6600 UD6400/UD6600

5 Tuner SEC_TC

6 DDR - - -

7 Light Effect OFF OFF OFF

8 Ch Table - - -

9 Country - - -

10 Front Color U-T-CL-M U-T-CL-M U-T-CL-M


13/94

2-7


2-3. New Functions Explanation

2-3-1. Smart Hub

'11 Smart Hub vs '10 Internet@TV

'11 Smart Hub Concepts and Features Launcher : Internet TV, Media

Play, Content Button

Search All : Provides integrated search results for avariety of areas

Full Browser : PC's Web browser, such as access to

common web site content and applications so you cansee

'10 Internet@TV

Internet TV, Media Player, content button

configured separately

Launcher - internet widget

Gallery -Free widget download / install

Horizontal / Vertical view modes

Internet@TV Button(Hot key on remote control)

Media. P Button(Hot key on remote control)

Comtent Button(Hot key on remote control)


14/94

2-8


Smart Hub Concepts

Gateway to access all type of diverse content

It's all integrated to guide you to easier diverse entertainment choice

Control your entertainment life with easy and simple user friends UI

Access to driverse Apps that are adding every day

Customize your TV, by App grouping & sorting to your taste


15/94

2-9


2-3-2. Seach all

Function

User can access the service using direct key on

remote control during TV viewing or using other App.

Supported four catecories

Your Movie: recommended movie or TV program

Top Application: popular Application list

Top Searched: popular searsh list

Search History

The application provides Web and SNS based search

engine.

YouTube Facebook

Your Movie

Samsung Apps

AllShare

Websites


16/94

2-10


2-3-3. AllShare

About AllShare

AllShareconnects your TV and compatible Samsung mobile phones/ devices through a network. On your TV,

you can view call arrivals and SMS messages, and received by your mobile phones. In addition, you can play media

contents including videos, photos, and music saved on your mobile phones or the other devices (such as your PC)

by controlling them on the TV via the network. Additionally, you can use your TV for browsing web pages on your

mobile phones.

NFor more information, visit www.samsung.com or contact the Samsung call center. Mobile devices may needadditional software installation. For details, refer to each devices users guide.

Setting Up AllShare

OMENU Network AllShare Settings ENTERE

AllShare Settings01.

Media (On / Off): Enables or disables the media function. When the media

function is on, you can control Media contents play using mobile phones or other

devices that support DLNA DMC.

Message (On / Off): Enables or disables the message function. (for call arrivals,and SMS messages received by your mobile phones)

Media / Message02.

Shows a list of mobile phones or connected devices which have been set up to use the Media or Message function

with this TV.

NThe Media function is available in all devices which support DLNA DMC.

Allowed / Denied : Allows/Blocks the devices.

Delete : Deletes the devices from the list.N This function only deletes the name of the device from the list. If the deleted device is turned on or tries to connect to the

TV, it may appear on the list again.

Using the Message Function03.

You can view call arrivals and SMS messages received by your mobile mobile phone, through the alarm window,

while watching TV.

NNOTETo disable the alarm window, set Messageto Off in the AllShare Settings.

Whether OKis selected or not selected after a message has appeared once, the message will be deleted from

the alarm window.

When a message from an unknown mobile phone is displayed, select the mobile phone in the Messagemenu in

AllShare Settings, and then select Deniedto block the phone.

Message View

If a new SMS message arrives while you are watching TV, the alarm window appears. If you select OK, the

contents of the message are displayed.

N You can congure the viewing settings for SMS messages on your mobile phones. For the procedures, refer to the mobile

phone manual.

N Some types of characters may be displayed as blank or broken characters.

Call Arrival Alarm

If a call arrives while you are watching TV, the alarm window appears.

Schedule Alarm

You can view scheduled events in the alarm window while you are watching TV.

N You can congure viewing settings for scheduled contents on your mobile phones. For the procedures, refer to the mobilephone manual.

N Some special characters may be displayed as blank or broken characters.


17/94

2-11


Using the Media Function04.

An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will

be displayed on your TV. The contents are played automatically 3 seconds after the alarm window appears. If you

press the RETURNor EXITbutton when the alarm window appears, the media contents are not played.

NNOTEThe first time a device accesses your TV through the media function, a warning popup window appears.

Press the ENTEREbutton to select Allow. This permits the phone to access the TV freely and use the Mediafunction to play content.

To turn off media contents transmissions from a mobile phone, set Mediato Offin the AllShare Settings.

Contents may not play on your TV depending on their resolution and format.

The ENTEREand l rbuttons may not work depending on the type of media content.

Using the mobile device, you can control the media play. For details, refer to each mobiles users guide.


18/94

2-12


AllShare setup and checklists

Problem Possible Solution

Deleted mobile phone list showing up

again.

[Menu > Application > Content View > AllShare > Message]

Where need to block the added mobile phone or device again. Because deleted

device would be added again if that device turns on or attempt to approach.

Want to turn off the function of receiving

message from the mobile phone.

One of the setup lists of AllShare, you need to turn 'Message' list to 'Off'.

Want to turn off the function of receiving

Media from mobile phone or home

network devices on TV.

One of the setup lists of AllShare, you need to turn 'Media' list to 'Off'.

Want to add deleted mobile phone or

home network devices again.

Power on the deleted mobile phone or home network devices.

Set up the network and activate the home network function, check the connection

at AllShare.

Several same names of TV shows up on

mobile phone.

At AllShare set up menu, change the name of the TV.

Messages/schedules/notications from

unknown mobile phone show up on TV.

[Menu > Application > Content View > AllShare > Message]

Where You can block the unknown mobile phone.

SMS message notication shows up in

small window.

Besides watching TV, If some other function is activating, SMS message will show

up in small icon.

You need to nish the function and exit to Watching TV mode in order to display

SMS message in large window.

Received SMS message is not showing

up on TV.

Check if TVs network setup is all right according to setup guide.

Check if mobile phones network (Wi-Fi) is activated.

Among the AllSharesetup lists , check if the Message is on.

Check if the mobile phone number is showing up on AllShare message list.

Check if the TVs showing up on mobile phones setup lists.

Contents that play on mobile phone

doesnt play on TV.

Contents formats play on TV is exactly same as Media Play format.That means some contents may not play according to its resolution and format

Suddenly TV display is changed,

unwanted movie/picture/music is playing

Before the device play, Block the device at AllShare media list.

Or press return or exit button of remote controller so that the device may not play.

The name of the TV is not appearing

while try to play media on mobile phone.

Check the network of TV.

Activate the network (Wi-Fi) of mobile phone and connect to home network .

Check if the setup list of media on AllShare is on.

Check if mobile phone is blocked on media list . If blocked, change it to permition.

Movie is not playing or disconnected. High resolution of Movie may not play when Wi-Fi network is not in good condition.


19/94

2-13


Troubleshooting about new functions


AllShare (General)

I see no device connected to AllShare. To use a device connected to AllShare, the device must be connected to PC

Share Manager which is the DLNA server for MediaPlay and to a cell phone thathas the Connected Home or Screen Share function which are found on Samsung

Smartphones.

Check that the PC Share Manager is enabled, the Samsung TV is set to allowconnections and the ScreenShare function on the connected cell phone is enabled.

To use the cell phones Connected Home function, check that the shared folder is

set and the Share mode is On.

I tried to play a video from my cell phone

using the Connected Home function on the

Samsung TV but the video would not display

on the TV.

When a video is transmitted from Connected Home to a TV for the rst time, thesettings screen that allows transfer to a TV is displayed.

Check that the transfer was not set to be rejected on this settings screen. If youhave set the cell phone to Blocked in the Media options of the AllShare settings,

please change the setting to Unblocked and retry.

A video that can be played on my cell phone

cannot be played on my TV.

Please check the resolution and display format provided by MediaPlay of the TV.

I cannot resume playback of a video using

Connected Home.

The resuming function is not supported for a video played on a cell phone.

When I play a video through Connected

Home, I get intermittent picture loss.

An 801.11b/g bandwidth network is used between a cell phone and a sharingdevice. There may be frequent buffering for HD quality videos, this also depends

on the condition of the wireless connection.

Please optimize your wireless Internet environment settings (avoid using wirelessInternet or bluetooth altogether if possible) or lower the picture quality of the video.

AllShare (Notication)

Can all devices with the DLNA function be

recognized through Notication?

Only Samsung software and devices with the DLNA server function can be

recognized through Notication.

Can I use all the services related to DLNA? Presently, you can only use the services related to ScreenShare and MediaPlay.We will launch a new DLNA service in the future.

The notication screen that appears after

a device connects disappears within a few

seconds.

How can I access this connected device

again?

The DLNA Notication is only displayed when a device is rst connected to a TV.

To access the device again, please use the AllShare menu.

AllShare (ScreenShare Client)

I cannot nd the RUIS on my cell phone. Check that the cell phone is connected to the wireless sharing device correctly.1.

Check that the DTV is connected either using a network cable or wirelessly to the2.

wireless sharing device correctly.

Conrm the IP address and subnet mask to ensure that the cell phone and DTV3.

are connected to the same network.

Check that the RUIS on the cell phone is enabled.4.

If the RUIS on the cell phone is enabled, please disable it and then enable it again.5.


20/94

2-14



AllShare (ScreenShare Server)

I cannot nd the remote control service

provided by the ScreenShare Server from the

ScreenShare Client.

Check that the ScreenShare Client device is correctly connected to the network of1.

the sharing device that the DTV is connected to.

Run network test in the network setup menu and conrm that MAC Address, IP2.

Address, Subnet, Gateway, DNS Server and Gateway Ping each shows a success

message.In the network setup menu, check that the ScreenShare Client and ScreenShare3.

Server are on the same subnet.

- You can conrm they are on the same subnet by checking the IP address,

subnet mask and gateway address of the TV and ScreenShare Client as follows:

- If the IP address of the DTV is 10.88.83.4 and the subnet mask is 255.255.255.0,

the rst six digits of the ScreenShare Clients IP address must be the same

(10.88.83) as that of the DTV, and the subnet mask and gateway address must

be the same as the DTV.

- If the IP address of the DTV is 10.88.83.4 and the subnet mask is 255.255.0.0,

the rst four digits of the ScreenShare Clients IP address must be the same

(10.88) as that of the DTV, and the subnet mask and gateway address must be

the same as the DTV.

Move from the Allshare screen to the Setup screen, and open the Setup menu to4.

check if the ScreenShare Client is connected to the same ScreenShare Server as

the TV name shown in the Setup options.Move from the Allshare screen to the Setup screen, and open ScreenShare to5.

check that the device, ScreenShare Client, is found on the list at the right side andis set to "Allowed."

The DTV did not update after pressing

buttons on the remote control that uses the

remote control service on the ScreenShare

Client.

Check that the TV is turned on.

You cannot turn on the TV using the remote control service (on the ScreenShare)

when the TV is turned off.


21/94

2-15


2-3-4. Media Play

Media Play

Functions that are not supported when connecting to a PC through a network:01.

- Sorting files by preference in the Photos, Music, and Videos folders.

- The(REW)or (FF)button while a movie is playing.

- Divx DRM, Multi-audio, embedded captions are not supported.

When you use Media Play mode through a network connection, depending on the functions of the02.provided server

- The sorting method may vary.

- The scene search function may not be supported.

- The Play Continuously function, which resumes playing of a video, may not be supported.

- The Play Continuously function does not support multiple users. (It will have only memorized the point where the most recent user

stopped playing.)

- The or buttons may not work depending on the content information.

If you experience any file stuttering issue while playing a video over a wireless network, we recommend using a wired network."

Supported Subtitle Formats

Name File extension Format

MPEG-4 time-based text .ttxt XML

SAMI .smi HTML

SubRip .srt string-based

SubViewer .sub string-based

Micro DVD .sub or .txt string-based

Supported Video Formats

File

ExtentionContainer Video Codec Resolution

Frame rate(fps)

Bit rate(Mbps)

Audio Codec

*.avi*.mkv

AVIMKV

Divx 3.11/4.x/5.1/6.0 1920 x 1080 6 ~ 30 8

MP3/AC3

/LPCM/ADPCM

/DTS Core

XviD 1920 x 1080 6 ~ 30 8

H.264 BP/MP/HP 1920 x 1080 6 ~ 30 25

MPEG4 SP/ASP 1920 x 1080 6 ~ 30 8

Motion JPEG 640 x 480 6 ~ 30 8

*.asf ASF

Divx 3.11/4.x/5.1/6.0 1920 x 1080 6 ~ 30 8

MP3/AC3

/LPCM

/ADPCM

/WMA

XviD 1920 x 1080 6 ~ 30 8

H.264 BP/MP/HP 1920 x 1080 6 ~ 30 25

MPEG4 SP/ASP 1920 x 1080 6 ~ 30 8

Motion JPEG 640 x 480 6 ~ 30 8

*.wmv ASF Window Media Video v9 1920 x 1080 6 ~ 30 25 WMA

*.mp4 MP4

H.264 BP/MP/HP 1920 x 1080 6 ~ 30 25

MP3/ADPCM /AACMPEG4 SP/ASP 1920 x 1080 6 ~ 30 8

XVID 1920 x 1080 6 ~ 30 8

*.3gp 3GPPH.264 BP/MP/HP 1920 x 1080 6 ~ 30 25 ADPCM/AAC

/HE-AACMPEG4 SP/ASP 1920 x 1080 6 ~ 30 8

*.vroVRO

VOB

MPEG2 1920 x 1080 24/25/30 30 AC3/MPEG

/LPCMMPEG1 1920 x 1080 24/25/30 30

*.mpg

*.mpegPS

MPEG1 1920 x 1080 24/25/30 30AC3/MPEG

/LPCM/AACMPEG2 1920 x 1080 24/25/30 30

H.264 1920 x 1080 6 ~ 30 25

*.ts*.tp*.trp

TS

MPEG2 1920 x 1080 24/25/30 30AC3/AAC/MP3/DD+

/HE-AAC

H.264 1920 x 1080 6 ~ 30 25

VC1 1920 x 1080 6 ~ 30 25


22/94

2-16


Other Restrictions03.

N NOTE

If there are problems with the contents of a codec, the codec will not be supported.

If the information for a Container is incorrect and the le is in error, the Container will not be able to play correctly.

Sound or video may not work if the contents have a standard bit rate/frame rate above the compatible Frame/sec listed in the

table above.

Video Decoder Audio Decoder

Supports up to H.264, Level 4.1

H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and

AVCHD are not supported.

XVID, MPEG4 SP, ASP:

Below 1280 x 720: 60 frame max

Above 1280 x 720: 30 frame max

GMC is not support.

Supports up to WMA 7, 8, 9, STD, 9 PRO

WMA 9 PRO is not supported the 2 channel excess multi

channel or the lossless audio

WMA sampling rate 22050Hz mono is not supported.

ReadlAudio 10 lossless is not supported


23/94

2-17


2-3-5. 3D Display

What is 3D Display?

A system that display 3D images articially

How ? Using binocular time delay

1Left eye recognizes left image, right eye recognizes

right image.2Human eyes be far away each other 65mm

horizontally.

So each eye feels a little bit of time delay of left and

right information.

Human brain merges those images and can feel

three-dimensional.

Side by side

3D OSD terms

3D Format: There are several 3D formats existing on how to merge Left and Right images.

Format Input images explanation Input source notes

Frame Packing Inserting Blink Active Space between Left and Right

images.

* Full resolution : 1920 x 1080 x 2

(Left and Right each) + Blink = 1920 x 2205

HDMI 1.4 1. HDMI 1.4 standard format

2. Automatically activating

(Not in the menu or UI)

3. BD format

Top & Bottom In 1 frame, Left image on the upper half, Right image

on the bottom half.

* Vertically half resolution

HDMI, USB,DTV(VOD),

PC

3D Broadcasting Format

Side by Side In 1 frame, Left image on the left half, Right image on

the right half.

* Horizontally half resolution

HDMI, USB,

DTV(VOD),PC

3D Broadcasting Format

2D 3D Extract Left and Right images articially from normal 2D contents input and show it in 3D. (a function of TV)

3D 2D When watching 3D TV (input is 3D source) , if a viewer feels tired of watching 3D TV, a viewer can change the TV into 2D. (In this case , TV only displays one of Left and Right images)

Depth Only activating in 2D 3D Mode

Control the depth of 3D. 1~10 steps, Tiredness goes higher as depth goes higher.

L/R correction Switch the position of Left and Right images so that correspond with 3D glasses.

3D Disable

(3D off)

3D off has below meanings according to present modes .

(1) In 2D 3D Mode : coming back to 2D

(2) In 3D mode


24/94

2-18


3D Supporting Formats

DTVInternet

VODATV/AV Comp. A.PC HDMI HDMI_PC

USB

(Photo)

USB

(Video)

Top-Bottom Over 720P All Resolution Over 720P - Over 720P Over 720P All Resolution All Resolution

Side by Side Over 720P All Resolution Over 720P - Over 720P Over 720P All Resolution All Resolution

2D3D All Resolution

MPO - - - - - - - All Resolution -

SAVE(SS.TB) - - - - - - - - All Resolution

HDMI 1.4a - - - - - Over 720P - - -

N : If the resolution is lower than 1920 x1080, PC Format(LL, VS, ChBD) and USB photo support only original size. : If the format is one of the below three case, the 20pixels on either side are processed by black.

- 2D 3D(all source)- Side by Side (component source)

- Top-Bottom (component source)USB photo : If the resolution is below 1920x1080, L/R images must be placed in the center of the screen

3D Glasses Enhancement in 2011

3D Format: There are several 3D formats existing on how to merge Left and Right images.

Item RF Auto On / Off

Purpose

To avoid external IR nois interference No power key

Improvement

RemarksDual Direction

Communication

Wear glasses Turn on

Take off glassesTurn off

Automatically


25/94

2-19


2-3-6. Built in Wi-Fi

Built in Wi-FiGives more convenient set-up and optimize to use Ethernet.

Smart TV Accessory - Wireless Router01.

Easy Set-up & Optimized Solution for using Ethernet

One Foot ConnectionEstablish a Wi-Fi connection to any compatible device placed within 25 cm distance(Samsung Patent pending)

USB configurationInsert USB to router Insert USB to Samsung TV

Configurations is safely stored on USB drive and restored on TV

Network Settings (OFC, One Foot Connection

The One Foot Connection function lets you connect your Samsung TV automatically to Samsung wireless APs.

If your non-Samsung AP does not support One Foot Connection, you must connect using one of the other methods.

How to set up using One Foot Connection01.

Go to Network Settings screen.1.

To enter it, follow the directions of Network Settings.

Select the One Foot Connection.2.

Place the AP in parallel with the Samsung Wireless LAN Adapter giving3.

a gap no larger than 25 cm.

Wait until the connection is automatically established.4.

The network test screen appears, and network setting is done.5.

Place the AP in a desired location.6.

Network Settings (Plug & Access)

Plug & Accessfunction lets you connect your Samsung wireless Router to Samsung TV easily by using USB memory. If

your non-Samsung AP does not support Plug & Access, you must connect using one of the other methods.

* You can check for equipment that supports Plug & Access on www.samsung.com.

How to set up using Plug & Access Function

Turn on the power of AP and TV.1.

Insert USB memory stick into our Samsung wireless APs and checking APs LED status (blinking on).

Then take USB memory out and insert your USB memory into Samsung TV.2.

Wait until the connection is automatically established.3.

If4. Plug & Accessdoes not connect your TV to your AP, a pop-up window appears on the screen notifying you of the failure. If you

want to try using Plug&Access again, reset the AP, disconnect the Samsung Wireless LAN Adapter and then try again from Step 1.

You can also choose one of the other connection setup methods.

The network test screen appears, and network setting is done.5.

Place the AP in a desired location.6.

If the AP settings change or you install a new AP, you must perform the7. Plug & Accessprocedure again, beginning from Step 1.


26/94

2-20



Network Setup

How do I setup the network? Click the [Menu] button and open [Setup] to select [Network].

Congure wired or wireless network settings.For details, please refer to the IB.

How do I check the network status? Select [Menu] [Setup] [Network] and run [Network Test] to see test results and

check the network status.

In a network test over a wired connection,

the second items which include the IP

address, subnet, gateway and DNS server

fail.

If the IP address, subnet mask and gateway address were typed in manually,check that valid values were entered.

(For example, 0.0.0.0 is not valid for an IP address, subnet mask or gateway

address.)

If the IP address the user entered in is invalid, change it to a valid IP address.

In a network test over a wired connection,

the third item, gateway ping fails.

Check that the network cable is connected to the TV correctly.1.

If the TV is connected correctly, check whether the IP address is automatic or2.

manual.If the IP is automatic and connected to a sharing device, check the settings of the3.

sharing device (AP) that is using a cable connection, or consult the corresponding

Internet service provider.

If the IP is manual, check if the IP address is entered correctly.4.

(Here, the user should conrm if the manual IP address entered in is valid.)

cannot connect to a wireless network. If an encryption key must be entered in to connect to a sharing device, please1.

check that the correct password set for the sharing device is entered.

Search surrounding sharing devices to see if there is a sharing device with the2.

same SSID by selecting [Wireless Network Setup] and [Select Network].

If there is a sharing device with the same SSID, try to connect to this device.

If the IP address is set to automatic and you cannot connect to the sharing3.

device using option 1 or 2, check the settings of the sharing device to see if theDHCP server function on the sharing device is enabled. If disabled, activate the

function. (For details on how to set up the sharing device, see the manual for thecorresponding sharing device.)

If you still cannot connect to the sharing device after conrming options 1, 2 and 3,4.

reset the sharing device and try again.

When using a wireless network, the users

wireless sharing device cannot connect to

the PBC (WPS).

Check if the sharing device of the user supports WPS.1.

(Refer to the manual of the sharing device.)

Check if the user pressed the PBC button on the sharing device.2.

If there is another sharing device with WPS running nearby, a connection cannot3.

be made. Please retry after 2 minutes.

Reset the sharing device and retry.4.

If the sharing device of the user is not Wi-Fi certied, it may not be able to connect5.

using WPS.

The auto-conguring sharing device cannotbe connected to automatically through a

wireless dongle.

(Here, the users sharing device must

support auto-conguration.)

Check if the sharing device of the user supports auto conguration.1.(For a list of sharing devices, refer to the IB or website.)

If the sharing device of the user supports auto conguration, place the sharing2.

device as close as possible to the wireless dongle on the TV and try to re-establish

the connection. (Must be placed close to the TV to establish a connection.)

Although the TV is placed close to the AP

and the dongle is inserted into the TV, the

sharing device cannot be connected to using

auto-conguration.

Select [Menu] [Setup] [Network] and check if SWL is Off.



sharing device cannot be connected to usingauto-conguration and a message that it is

connecting is displayed only.

Check if the AP is not turned off during connection.If the AP is turned off, the TV will try to re-establish a connection for 2 minutes.


27/94

2-21





sharing device cannot be connected to using

auto-conguration and a message that it is

connecting is displayed only.

If Samsung Wireless Link is On, a 5G-bandwidth wireless sharing device may not

be found in a search (restriction).

If Samsung Wireless Link is Off or the product does not have the SamsungWireless Link function, please retry searching to nd the sharing device. (May not

be found in a search depending on the settings of the wireless connection.)

In a network test over a wireless connection,

the second items which include the IP

address, subnet, gateway and DNS server

fail.

If the IP address, subnet mask and gateway were typed in manually, check that

valid values were entered. (For example, 0.0.0.0 is not valid for an IP address,

subnet mask or gateway address.)

If the IP address the user entered in is invalid, change it to a valid IP address.


the third item, gateway ping fails.

If the IP address is automatic and connected to a sharing device, check the1.

settings of the sharing device (AP) that is using a cable connection, or consult thecorresponding Internet service provider.

If the IP address is manual, check that the IP address is entered in correctly.2.

(Here, the user should conrm if the manual IP entered in is valid.)


the fourth item, Internet service test fails.

Please consult the corresponding Internet service provider (an Internet network

service provider the user has subscribed to such as KT).


28/94

2-22


2-4. Accessories

Product Description Code. No Remark

Remote Control & Batteries

(AAA x 2)

AA59-00445A

AA59-00453A

(Ready models)

4301-000121

Samsung Electronics

Service center

Power Cord

3903-000525

3903-000539

(UK)

Warranty Card /

Registration Card /

Safety Guide Manual

-

User Manual

(Simple Guide)

BN68-03478* (UA**D6400, DTV)BN68-03479* (UA**D6400, Ready)

BN68-03485* (UA**D6600, DTV)

BN68-03484* (UA**D6600,Ready)

Holder-Wire stand BN61-05491A

Holder-Ring (4ea) BN61-05280A

AV Adapter BN39-01154H

Component+AV Adaptor BN39-01154W


29/94


30/94


31/94


32/94


33/94


34/94


35/94


36/94


37/94


38/94


39/94


40/94


41/94


42/94


43/94


44/94


45/94


46/94


47/94


48/94


49/94


50/94


51/94


52/94


53/94


54/94


55/94


56/94


57/94


58/94


59/94


60/94


61/94


62/94


63/94


64/94


65/94


66/94


67/94


68/94


69/94


70/94


71/94


72/94


73/94


74/94


75/94


76/94


77/94


78/94


79/94


80/94


81/94


82/94

*


83/94


84/94


85/94


86/94


87/94


88/94


89/94


90/94

5. Wiring Diagram

5-1. Wiring Diagram For 40"

MainBoard

T-CO

N

SMPS

SPEAKER

SPEAKER

Wi-

Fi

F u n c t i o n

B T I R

5-1

5. Wiring Diagram


91/94

For 46"_55"

MainBoard

T-CON

SMPS

SPEAK

ER

SPEAKER

Wi-

Fi

F u n c t i o n

B T I R

5-2

5. Wiring Diagram


92/94

5-2. Connector For All Inch

CN1601

1 NC 42 TX1_AN

2 GND 43 GND

3 TCON_EEPROM_WP 44 GND

4 BLACK_INS_SYNC 45 GND

5 TCON_RESET 46 NC

6 NC 47 PANEL_VCC

7 GND 48 PANEL_VCC

8 SDA_TCON 49 PANEL_VCC

9 PANEL_WP 50 PANEL_VCC

10 LUT_SELECT0 51 PANEL_VCC

11 3D_ENABLE 52 GND

12 SCL_TCON 53 TX2_AN

13 GND 54 TX2_AP

14 TX3_EP 55 TX2_BN

15 TX3_EN 56 TX2_BP

16 TX3_DP 57 TX2_CN

17 TX3_DN 58 TX2_CP

18 GND 59 GND

19 TX3_CLKP 60 TX2_CLKN

20 TX3_CLKN 61 TX2_CLKP

21 GND 62 GND

22 TX3_CP 63 TX2_DN

23 TX3_CN 64 TX2_DP

24 TX3_BP 65 TX2_EN

25 TX3_BN 66 TX2_EP

26 TX3_AP 67 GND

27 TX3_AN 68 TX4_AN

28 GND 69 TX4_AP

29 TX1_EP 70 TX4_BN

30 TX1_EN 71 TX4_BP

31 TX1_DP 72 TX4_CN

32 TX1_DN 73 TX4_CP

33 GND 74 GND

34 TX1_CLKP 75 TX4_CLKN

35 TX1_CLKN 76 TX4_CLKP

36 GND 77 GND

37 TX1_CP 78 TX4_DN

38 TX1_CN 79 TX4_DP

39 TX1_BP 80 TX4_EN

40 TX1_BN 81 TX4_EP

41 TX1_AP 82 GND

CN602(to HDMI1)

1 HDMI1_RX2+ 11 GND

2 GND 12 HDMI1_RXCLK-

3 HDMI1_RX2- 13 HDMI_CEC

4 HDMI1_RX1+ 14 GND

5 GND 15 HDMI1_DDC_SCL

6 HDMI1_RX1- 16 HDMI1_DDC_SDA

7 HDMI1_RX0+ 17 GND

8 GND 18 HDMI1_5V

9 HDMI1_RX0- 19 HDMI1_HPD

10 HDMI1_RXCLK+

CN603(to HDMI2)

1 HDMI2_RX2+ 11 GND

2 GND 12 HDMI2_RXCLK-


4 HDMI2_RX1+ 14 GND



7 HDMI2_RX0+ 17 GND

8 GND 18 HDMI2_5V


10 HDMI2_RXCLK+

CN604(to HDMI3)

1 HDMI3_RX2+ 11 GND

2 GND(MHL_AON) 12 HDMI3_RXCLK-


4 HDMI3_RX1+ 14 GND



7 HDMI3_RX0+ 17 GND

8 GND 18 HDMI3_5V


10 HDMI3_RXCLK+

CN601(to HDMI4)

1 HDMI3_RX2+ 11 GND

2 GND(MHL_AON) 12 HDMI3_RXCLK-


4 HDMI3_RX1+ 14 GND



7 HDMI3_RX0+ 17 GND

8 GND 18 HDMI3_5V


10 HDMI3_RXCLK+

5-3

5. Wiring Diagram


93/94

CN401(to PC)

1 PC_RED 9 PC_5V

2 PC_GREEN 10 IDENT_PC

3 PC_BLUE 11 NC

4 NC 12 SDA_DOWN

5 GND 13 PC_H_SYNC

6 GND 14 PC_V_SYNC

7 GND 15 SCL_DOWN

8 GND

CN402(to PC Sound)

1 GND 4 NC

2 PC_SL_IN 5 NC

3 PC_SR_IN 6 NC

CN301(to Speaker)

1 R+ 3 L+

2 R- 4 L-

CN303(to Optical Jack)

1 SPDIF_OUT 3 GND

2 VCC

CN1502(to Side USB1)

1 USB0_VCC_PW 3 USB_DP

2 USB0_DM 4 GND


1 USB2_VCC_PW 3 USB2_DP

2 USB2_DM 4 GND


1 USB3_VCC_PW 3 USB3_DP

2 USB3_DM 4 GND

CN502(to Headpune&Monitor OUT)

1 GND 4 IDENT_HP

2 HP_LINE_SL_OUT 5 GND

3 HP_LINE_SR_OUT 6 HP_LINE_SL_OUT

CN404(to Component & AV)

1 GND 6 GND

2 COMP_Y_AV1 7 IDENT_COMP

3 COMP_PB 8 AV1_SL_IN

4 IDENT_AV1 9 AV1_SR_IN

5 COMP_PR

CN401(to Function/IR)

1 IR 10 USB_BT_DM

2 FRAME_SYNC_IN 11 WAKE

3 GND 12 A5V

4 3D_SYNC_BT 13 A3.3V

5 A3.3V 14 LED_STB

6 GND 15 IR_SYNC

7 MSCL_A5V 16 POWER_DET

8 USB_BT_DP 17 GND

9 MSDA_A5V 18 NC

CN201(to Power board)

1 B5V 11 B13V

2 SW_POWER_OUT 12 B13V

3 B5V 13 B13V

4 A5V 14 PWM_DIM1_CPLD_OUT

5 GND 15 GND

6 GND 16 PWM_DIM2_CPLD_OUT

7 B18VS 17 OVD_ON

8 DGND 18 PWM_DIM3_CPLD_OUT

9 B18VS 19 OVD_LEVEL

10 SW_INVERTER 20 PWM_DIM4_CPLD_OUT

5-4

5. Wiring Diagram


94/94

5-3. Connector Functions

Connector Functions

CN201CN803 Supply power from SMPS to Main Board.

CN1601J101 The LVDS signal transfered from Main Board to Panel.

5-4. Cables

Use Main-SMPS Main-T-CON Function-Main

Code40" : BN39-01475B

46" : BN39-01475C

55" : BN39-01474A

40" : BN96-18130B

46" : BN96-18130C

55" : BN96-17116K

40" : BN39-01480A

46" : BN39-01480C

55" : BN39-01480E

Photo

40"/46"

55"

5-5. Types of module

Use Wi-Fi module Bluetooth module IR module IR/Function module

Code BN59-01130A BN96-17107A BN96-18099A BN96-18232B

Standard IEEE802.11abgn - - -

Photo

5. Wiring Diagram

Documents

Samsung Ua40d6000sjxxz Sm