Upload
mehdipalangi
View
368
Download
5
Tags:
Embed Size (px)
DESCRIPTION
Samsung
Citation preview
SERVICE
SAMSUNG COLOR LASERPRINTER
CLP-510/XBH
Manual
SAMSUNG COLOR LASER PRINTER CONTENTS
1. Precautions
2. Reference Information
3. Specifications
4. Summary of product
5. System Outline
6. Disassembly and Reassembly
7. Alignment and Adjustments
8. Troubleshooting
9. Exploded Views and Parts List
10. Block Diagram
11. Connection Diagram
Basic Model : CLP-510/CLP-510N
11
1-1
Precautions
Service Manual
1. PrecautionsIn order to prevent accidents and to prevent damage to the equipment please read the precautions listedbelow carefully before servicing the printer and follow them closely.
1.1 Safety Warning
(1) Only to be serviced by appropriately qualified service engineers.High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitablytrained and qualified service engineer.
(2) Use only Samsung replacement partsThere are no user serviceable parts inside the printer. Do not make any unauthorized changes or additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
(3) Laser Safety StatementThe Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J forClass 1(1) laser products, and elsewhere, it is certified as a Class I laser product conforming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. Thelaser system and printer are designed so there is never any human access to laser radiation above a Class Ilevel during normal operation, user maintenance, or prescribed service condition.
Warning >> Never operate or service the printer with the protective cover removed from Laser/Scanner assembly. Thereflected beam, although invisible, can damage your eyes. When using this product, these basic safety pre-cautions should always be followed to reduce risk of fire, electric shock, and injury to persons.
CAUTION - INVISIBLE LASER RADIATION WHEN THIS COVER OPEN. DO NOT OPEN THIS COVER.
VORSICHT - UNSICHTBARE LASERSTRAHLUNG, WENN ABDECKUNG GE FFNET. NICHT DEM STRAHL AUSSETZEN.
ATTENTION - RAYONNEMENT LASER INVISIBLE EN CAS D OUVERTURE. EXPOSITION DANGEREUSE AU FAISCEAU.
ATTENZIONE - RADIAZIONE LASER INVISIBILE IN CASO DI APERTURA. EVITARE L ESPOSIZIONE AL FASCIO.
PRECAUCION - RADIACION LASER IVISIBLE CUANDO SE ABRE. EVITAR EXPONERSE AL RAYO.
ADVARSEL. - USYNLIG LASERSTR LNING VED BNING, N R SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDG UDSAETTELSE FOR STR LNING.
ADVARSEL. - USYNLIG LASERSTR LNING N R DEKSEL PNES. STIRR IKKE INN I STR LEN. UNNG EKSPONERING FOR STR LEN.
VARNING - OSYNLIG LASERSTR LNING N R DENNA DEL R PPNAD OCH SP RREN R URKOPPLAD. BETRAKTA EJ STR LEN. STR LEN R FARLIG.
VARO! - AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA N KYM TT M LLE LASER-S TEILYLLE L KATSO S TEESEEN.
1-2
Precautions
Service Manual
1.2 Caution for safety
1.2.1 Toxic material
This product contains toxic materials that could cause illness if ingested.
(1) If the LCD control panel is damaged it is possible for the liquid inside to leak. This liquid is toxic. Contact with the skinshould be avoided, wash any splashes from eyes or skin immediately and contact your doctor. If the liquid gets intothe mouth or is swallowed see a doctor immediately.
(2) Please keep toner cartridges away from children. The toner powder contained in the toner cartridge may be harmfuland if swallowed you should contact a doctor.
1.2.2 Electric Shock and Fire Safety Precautions
Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electricshock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cableto overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead toa fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paperclips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electricshock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. Whenservicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted com-pletely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the powerconnector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or other wise damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat andcause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable, weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should berepaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected fromthe power source when such weather conditions are expected. Do not touch the machine or the power cord if itis still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machinenear a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possiblyleading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it couldmake contact with a high voltage conductor inside the machine and cause an electric shock.
1-3
Precautions
Service Manual
1.2.3 Handling Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could causethe printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which ifspilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to ahumidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc on the printer, these could cause a fire.
1.2.4 Assembly / Disassembly Precautions
Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if themainboard or network card is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperaturerating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room lighting. Exposure for as little as 5 mins can damage the surface’s photoconductive properties and will resultin print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it ina black bag or other lightproof container. Take care when working with the covers(especially the top cover)open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
1-4
Precautions
Service Manual
1.2.5 Disregarding this warning may cause bodily injury
(1) Take care - some parts may be hot.The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cooldown before disassembly.
(2) Take care not to trap fingers or hair.Take care when using a printer. It contains many rotating parts. Ensure that fingers, hair, clothing etc. do notbecome caught in the mechanism as this could cause injury.
(3) When you move the printer.This printer weighs 32kg including toner cartridge and cassette. Use safe lifting and handling techniques. Usethe lifting handles located on each side of the machine. Back injury could be caused if you do not lift carefully.
(4) Ensure the printer is installed safely.The printer weighs 32Kg, ensure the printer is installed on a level surface, capable of supporting its weight.Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.
1-5
Precautions
Service Manual
1.3 ESD Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some fieldeffect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused bystatic electricity.
Caution >>Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off anyelectrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially avail-able wrist strap device, which should be removed for your personal safety reasons prior to applying power to theunit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such asaluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assem-bly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” cangenerate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to dam-age ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Mostreplacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a compa-rable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the pro-tective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until com-pletely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushingtogether of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient todamage an ESD.
1.4 Super Capacitor or Lithium Battery Precautions
1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion andsubsequent operator injury and/or equipment damage if incorrectly installed.
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturers.
3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned fordisposal.
4. Dispose of used batteries according to the manufacturer’s instructions.
1-6
Precautions
Service Manual
MEMO
22
2-1Samsung Electronics
Reference Information
Service Manual
2. Reference InformationThis chapter contains the tools list, list of abbreviations used in this manual, and a guide to thelocation space required when installing the printer. A definition of tests pages and WirelessNetwork information definition is also included.
2.1 Tools for Troubleshooting
The following tools are recommended safe and easy troubleshooting as described in this service manual.
• DVM(Digital Volt Meter)Standard : Indicates more than 3 digits.
• DriverStandard : "-" type, "+" type (M3 long, M3 short, M2
long, M2 short).
• TweezersStandard : For general home use, small type.
• Cotton SwabStandard : For general home use, for medical service.
• Cleaning EquipmentsStandard : An IPA(Isopropyl Alcohol)dry wipe tissue or a
gentle neutral detergent and lint-free cloth.
• Vacuum Cleaner
• Brush
• Software (Driver) installation CD ROM
Install Driver CD
Network S/W CD
2-2
Reference Information
Samsung ElectronicsService Manual
2.2 Acronyms and Abbreviations
The table below explains the abbreviations and acronyms used in this service manual. Where abbreviationsor acronyms are used in the text please refer to this table.
ADC Analog-to-Digital-Conversion
AP Access Point
AC Alternating Current
ASIC Application Specific IntegratedCircuit
ASSY Assembly
BIOS Basic Input Output System
BLDC Motor Brushless DC Motor
CLBP Color Laser Beam Printer
CMOS Complementary Metal OxideSemiconductor
CMYK Cyan, Magenta, Yellow, Black
CN Connector
CON Connector
CPU Central Processing Unit
CTD Sensor Color Toner Density Sensor
dB Decibel
dBA A-Weighted decibel
dBm Decibel milliwatt
DC Direct Current
DCU Diagnostic Control Unit
DIMM Dual In-line Memory Module
DPI Dot Per Inch
DRAM Dynamic Random Access Memory
DVM Digital Voltmeter
ECP Enhanced Capability Port
ECU Engine Control Unit
EEPROM Electronically ErasableProgrammable Read Only Memory
EMI Electro Magnetic Interference
EP Electro photographic
EPP Enhanced Parallel Port
F/W Firmware
FCF/FCT First Cassette Feeder/FirstCassette Tray
FISO Front-In, Side-Out
FPOT First Print out Time
GDI Windows Graphic Device Interface
GIF Graphic Interchange Format
GND Ground
HBP Host Based Printing
HDD Hard Disk Drive
HTML Hyper Text Transfer Protocol
HV High Voltage
HVPS High Voltage Power Supply
I/F Interface
I/O Input and Output
lb Pound(s)
IC Integrated Circuit
ICC International Color Consortium
IDE Intelligent Drive Electronics orIntegrated Drive Electronics
IEEE Institute of Electrical andElectronics Engineers. Inc
IOT Image Output Terminal (Color print-er, Copier)
IPA Isopropy Alcohol
IPC Inter Process CommunicationEPPEnhanced parallel Port
IPM Images Per Minute
ITB Image Transfer Belt
LAN local area network
LBP Laser Beam Printer
2-3Samsung Electronics
Reference Information
Service Manual
LCD Liquid Crystal Display
LED Light Emitting Diode
LSU Laser Scanning Unit
MB Megabyte
MHz Megahertz
MPBF Mean Prints Between Failure
MPF/MPT Multi Purpose Feeder/MultiPurpose Tray
NIC Network Interface Card
NPC Network Printer Card
NVRAM Nonvolatile Random AccessMemory
OPC Organic Photo Conductor
PBA Printed Board Assembly
PCL Printer Command Language ,Printer Control Language
PCI Peripheral ComponentInterconnect by Intel 1992/6/22, isa local bus standard developed byIntel and introduced in April, 1993 :A60, B60 Pins
PCL5Ce Printer Command Language 5Ce-Color
PCL6 Printer Command Language 6
PDF Portable Document Format
PDL Page Description Language
Ping Packet internet or Inter-NetworkGroper
PPD Postscript Printer Discription
PPM Page Per Minute
PS Post Script
PS3 Post Script Level3
PTL Pre-Transfer Lamp
PWM Pulse Width Moduration
Q’ty Quantity
RAM Random Access Memory
RCP Remote Control Panel
ROM Read Only Memory
SCF/SCT Second Cassette Feeder/SecondCassette Tray
SMPS Switching Mode Power Supply
SPGP Samsung Printer GraphicProcessor
SPL Samsung Printer Language
SPL-C Samsung Printer Language-Color
Spool Simultaneous Peripheral OperationOnline
SRS Software Requirment Specification
SURF Surface Rapid Fusing
SW Switch
sync Synchronous or Synchronization
T1 ITB
T2 Transfer Roller
TRC Toner Reproduction Curve
PnP Universal Plug and Play
U.I. User Interface
URL Uniform Resource Locator
USB Universal Serial Bus
VCCI Voluntary Control Council forInterference InformationTechnology Equipment
WECA Wireless Ethernet CompatibilityAlliance
Wi-Fi Wireless Fidelity
2.3 Select a location for the printer
• Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagrambelow)
• Provide the proper environment :- A firm, level surface- Away from the direct airflow of air conditioners, heaters, or ventilators- Free of extreme fluctuations of temperature, sunlight, or humidity- Clean, dry, and free of dust
2-4
Reference Information
Samsung ElectronicsService Manual
2-5Samsung Electronics
Reference Information
Service Manual
2.4 A4 ISO 19752 Standard Pattern
This test page is reproduced at 70% of the normal A4 size
2-6
Reference Information
Samsung ElectronicsService Manual
2.5 Wireless LAN
• This product can be used with a wireless LAN, (this is an option.)- The wireless LAN function uses radio technology, instead of using LAN cable, to connect to an
access point for printing.- For a wireless LAN connection in Infrastructure mode an AP is needed, (purchased separately) - For a wireless LAN connection in Ad-Hoc mode an appropriate Wireless I/F card is required fitted
to a computer, (purchased separately)- It is possible to use a wireless LAN connection with wired LAN. - If an AP is installed in an office or at home, the wireless LAN function can be simply configured
and used.
• Types of desk top PC (or Lap top) that uses the wireless LAN.
• About the certificated mark of Wi-FiTM
- Wi-FiTM is a registered trademark of the WECA (Wireless EthernetCompatibility Alliance). Over 50 wireless LAN companies are member ofthis organisation. Most of the main wireless networking companies areattending including such companies as Lucent Technologies, Cisco,Intel/Symbol, 3Com, Enterasys (Cabletron), Compaq, IBM, Nokia, Dell,Philips, Samsung Electronics, Sony, Intersil, etc.. This mark certifies mutualcompatibility amongst the product of these companies. Wi-FiTM (IEEE802.1) is certified as a standard of the wireless LAN market.
Division Basic type Recommend type
CPU Over PENTIUM 233M PENTIUM 300MHz
MEMORY Over 64MB Over 128MB
VIDEO CARD Over 800X600 Over 1024X768
OS Over WINDOWS 98 Over WINDOWS ME
INTERFACE CARD A product has a certificated mark of Wi-FiTM
33
3-1Samsung Electronics
Specifications
Service Manual
3. SpecificationsSpecifications are correct at the time of printing. Product specifications are subject to change without notice.See below for product specifications.
3.1 General SpecificationsItems Descriptions
Print Method Non-impact Electro-photography
Developing system Non-Magnetic, Mono-Component Developing System
*Print Speed Mono Up to 24 PPM in A4, Up to 25 PPM in Letter size
Color Up to 6 PPM in A4, Up to 6 PPM in Letter size
Resolution Up to 1200 DPI effective output, True 600 X 600dpi
Source of Light Laser diode (LSU : Laser Scanning Unit)
Warm-Up Time More than 99 sec
First Print Time Mono 15 seconds (Ready to 1st page out)
Color 24 seconds (Ready to 1st page out)
Feed Method Cassette , MPT(Multi Purpose Tray), SCT(Second Cassette Tray)
Media Size 76 X 128mm (3 x 5”) to 216 X 356mm (8.5 X 14”)
Media Thickness Cassette : 16 ~24 lb , MPT : 16 ~ 43 lb
Dimension (W X D X H) 510 X 470 X 405 mm
Weight Net 25.5 Kg 56.2Lbs
Gross 32.0 Kg 70.5Lbs
**Acoustic Noise Stand by More than 40 dBA-TBD
Printing More than 48 dBA (Color)-TBD
Power save mode Available, Setting : 5min/10min/15min/30min/45min/60min/120min
Toner save mode Disable
Machine Life Mono : More than 300,000 pages, Color : More than 75,000 pages
* Print speed will be affected by Operating System used, computing performance, application software, connectingmethod, media type, media size and job complexity.
* Cardstock/Envelope : Half Speed
** Sound Pressure Level, ISO 7779
3-2
Specifications
Samsung ElectronicsService Manual
3.2 Controller Specification
3.3 Electrical Specification
Items DescriptionsProcessor (CPU) Samsung SPGPm (CLOCK SPEED 120Mhz), 32-bit RISC core (ARM 946ES)
Memory FLASH ROM (PROGRAM) : 8MB flash
*RAM : 64MB (Expandable to 320MB : With Option
Option DIMM module : 64/128/256MB
100Pin SDRAM DIMM (Samsung Printer Only)
EEPROM (NVRAM) : 1024bytes
Emulation SPL-Color
Operating System Win 95/98/ME/NT4.0/2000/XP, Various Linux OS including Red Hat, Caldera, Debian,Mandrake, Slackware, SuSE and Turbo Linux
Interface Parallel : IEEE 1284 Bidirectional (Korea, Russia, Asia only)
- Modes supported : Compatible, Nibble, Byte, ECP
USB (without HUB mode)
- USB 2.0 compliant -12/480 Mbps 1 port
Network Interface
- 10/100 Base TX
10/100 Base TX + 802.11b Wireless LAN
Interface switching Automatic
Interface time-out 5min (Max.)
Font Windows font, PS english font, PCL english font
Color Management ICC ICM V3.4
* Memory Slots : Standard Capacity is64MB Option Capacity is 320MB (Max)(100Pin 1 slot, 64MB/128MB/256MB)
Items Descriptions RemarksInput Voltage Nominal input voltage 200-240 VAC / 100~127VAC
Input voltage range 180-264 VAC/ 90~132VAC
Nominal frequency 50/60 MHz
Frequency tolerance +3Hz
Power Consumption Printing :450W max (with SCF)
Power Save : 35W max
3.4 Environmental RangeItems Operating Storage
Temperature 15~32.5 ˚C(50-90 ˚F) -20~40 ˚C (-4~104 ˚F)
Humidity 20~80%RH 10~80%RH
3-3Samsung Electronics
Specifications
Service Manual
3.5 Consumable & Maintenance Items
Items Descriptions RemarksPeriodic Replacing Parts Toner Cartridge(Black) initial (3,000 pages@5% coverage) User replace
replacement (7,000 pages@5% coverage)
Toner Cartridge(Cyan) initial (2,000 pages@5% coverage) User replace
replacement (5,000 pages@5% coverage)
Toner Cartridge(Magenta) initial (2,000 pages@5% coverage) User replace
replacement (5,000 pages@5% coverage)
Toner Cartridge(Yellow) initial (2,000 pages@5% coverage) User replace
replacement (5,000 pages@5% coverage)
OPC Unit mono : 50,000 pages User replace
color : 12,500 pages
ITB Unit(T1 Roller) mono : 50,000 pages User replace
color : 12,500 pages
Waste Toner Tank 3,000 images User replace
Fuser Unit simplex : 100,000 page (Mono) / 50,000 page (Color) Engineer
duplex : 50,000 page (Mono) / 25,000 page (Color)
Transfer Roller(T2 Roller) simplex : 50,000 page Engineer
duplex : 25,000 page
Option SCT - Paper capacity : 500sheets
(Second Cassette Tray) - Paper weight : 60 ~ 90 g/m2 / 16 ~ 24 lbs
Network Printing - Ethernet 10/100baseTX + Wireless
- Protocols : TCP/IP, SPX/IPX, Ethertalk, SNMP, HTTP1.1, DLC/LLC
- 8MB RAM Buffer for faster graphics performance
- 4MB Flash Memory for upgrade
802.11b Wireless LAN - IEEE802.3b support
- speed : 11, 5.5, 2 ,1Mbps
- WEP : 64bit, 128bit
- Operating range : 30m(Indoors) , 100m(Outdoors)
SDRAM DIMM - 64,128MB, 256MB 100Pin SDRAM DIMM(Use SamsungPart Only)
3-4
Specifications
Samsung ElectronicsService Manual
3.6 Paper handling Specifications
Paper Paper size 1st Cassette 2nd Cassette MP tray Duplex
A4 210 X 297 mm O O O O
Letter 216 X 279 (8.5 X 11") O O O O
Folio (Legal13") 216 X 330 (8.5 X 13") O O
Legal (Legal14") 216 X 356 (8.5 X14") O O
Executive 184 X 267 (7.25 X10.5") O
Statement 140 X 216(5.5 x8.5") O
ISO B5 176 X 250 O
JIS B5 182 X257 O
A5 148.5 X 210 O
A6 105 X148.5 O
Com-10 Envelope 105 X 241 (4.15 X 9.5") O
Monarch Envelope 98 X191 (3.87 X 7.5") O
DL Envelope 110 X 220(4.33 X 8.66") O
C5 Envelope 162 X 229 (6.38 X 9.01") O
C6 Envelope 114 X 162 (4.49 X 6.38") O
Transparency (OHP) A4 or Letter O
Label paper A4 or Letter O
3.6.2 Input Capacity
3.6.1 input Paper Size
Items Descriptions RemarksCassette(FCT) 250 sheets
MP tray Paper 100 sheets
Transparencies 30 sheets
Envelopes 10 sheets
Labels 10 sheets
Option Cassette(SCT) 500 sheets
3.6.3 Output Capacity
Items Descriptions RemarksFace Down 250 sheets
O : Supported
44
4-1Samsung Electronics
Summary of product
Service Manual
4. Summary of ProductThis chapter describes the functions and operating principles of the main components.
4.1 System Structure
4.1.1 Main Parts of SystemH
VP
S
Eraser LampEraser Lamp
HV
PS
DEV. - Black
DEV. - YellowO
PC
Pick-upRoller
DEV. - Magenta
DEV. - Cyan
CASSETTE LS
U
ITB
Un
itFeeder
DUPLEX T2 Roller
Fuser Unit
EXIT Unit
MPF Path
MPFMPT
DEV. - Black
DEV. - YellowO
PC
Pick-upRoller
DEV. - Magenta
DEV. - Cyan
SCFS
CT
FC
T
LS
U
Deve CoverDeve CoverIT
B U
nitFeeder
DUPLEX T2 Roller
Fuser Unit
EXIT Unit
PTL PTLSCF Path
Pick-upRoller
Pick-upRoller
Pick-upRoller
Pick-upRoller
4-2
Summary of Product
Samsung ElectronicsService Manual
>> Front View
Deve OEM PBA
Panel PBA
Waster Toner Sensor
Waster Toner Motor
SMPSSMPS
Main DriveMain Drive
Fan Fan
Deve DriveDeve DriveDeve Drive PBADeve Drive PBA
Duplex Cover Open S/W
Duplex Cover Open S/W
Deve Cover Open S/W
Deve Cover Open S/W
Main Conrtoller PBAMain Conrtoller PBA
>> Rear View
4-3Samsung Electronics
Summary of product
Service Manual
1) OPC UnitImages are created on the OPC unit using an electro-photographic process. The unit consists of:-* OPC Drum* Waste Toner Ass'y used to collect waste toner remaining on the OPC drum, * Charge Roller Assy
2) ITB UnitITB stands for Image Transfer Belt. An image developed on the OPC Drum is transferred first to theITB. This is called the T1 Transfer (Primary Image Transfer).Images are built up in layers on the ITB. First the Yellow (Y) colour image is created on the OPC and transferred to the ITBNext the Magenta (M) colour image is created on the OPC and transferred to the ITBFollowed by the Cyan (C) and Black (K) images.
3) Transfer RollerOnce the complete, full colour, image, has been built up on the ITB the Transfer Roller is used totransfer the image onto paper. This is called the T2 Transfer (Secondary Image Transfer)
4) FCT (First Cassette Tray)It stores and automatically feeds print paper.
Pick-up Roller picks up paper, controls drive, feeds paper, removes static electricity, and so on.
> Spec.* Paper arrange way : Side Registration* Paper Direction : FISO (Front-in, Side-Out)* Cassette Type : A4, Ltr* Paper Discharge : Separation Claw* Capacity : 250 Sheets (Standard paper 75mg/m? 20lb)* Paper Size : A4, Letter* Paper Weight (average) : 60~90g/m2 (16~24lbs)* Paper Type : General Printing Paper* Additional Function : Paper Empty Sensor
5) SCT (Second Cassette Tray)This additionally stores and automatically feeds printing paper. Its function is the same as the FCT(First Cassette Tray)
> Spec.* Paper arrangement : Side Registration* Paper Direction : FISO (Front-in, Side-Out)* Cassette Type : A4, Ltr* Paper Discharge : Separation Claw* Capacity : 500 Sheets (Standard paper 75mg/m2 20lb)* Paper Size : A4, Letter* Paper Weight (average) : 60~90g/m2 (16~24lbs)* Paper Type : General Printing Paper* Additional Function : Paper Empty Sensor
4-4
Summary of Product
Samsung ElectronicsService Manual
6) MPT (Multi Purpose Tray)The Multi-Purpose Tray not only feeds general printing paper but is also used for many other kindsof paper such as those paper sizes not supported by the cassette, envelopes, OHP, etc. > Spec.
* Capacity : Cut Sheet : 100 Sheets (Standard paper 75mg/m2 20lb)* OHP : 300 Sheets* Envelope & Label & Card Stock : 10 Sheets* Paper Arrangement : Side Registration* Power : Main Motor (BLDC)* Driving Management : Solenoid* Paper Discharge : Friction Pad Method* Paper Size : Legal, Folio, A4, Letter, Executive, JIS B5, A5, A6* Paper Weight (Average) : 60~163g/m2
* Paper Type : General, Label, Post Card, Transparency, Envelope, Card Stock (TracingPaper is not served)
* Additional Function : Paper Empty Sensor
7) Feeder* Paper Arrangement : Side Registration.* Power : Main Motor (BLDC)* Paper Management : Solenoid
8) Duplex UnitThe Duplex Unit is used to reverse feed paper when printing on the second side (known as Doublesided or Duplex printing). The Duplex Unit is not an optional extra, it is built-in at manufacturingtime and is integral with the Transfer Roller.> Spec.
* Power : Main Motor (BLDC)* Paper Reverse Function: After the front side of the original document is printed, it is transferred
to the duplex unit in order to print the reverse side of original document. The motor drivesthe exit roller in the reverse direction to feed the paper back into the machine.
9) Exit UnitThe Exit Unit guides paper that is just about to leave the print engine. Printed-paper is dischargedby the Exit Roller and Kicker into the Output Tray. > Spec.
* Capacity : 250 sheets (Standard A4, 75g/m2)* Paper Direction : Face Down* Exit Drive Roller : It is driven by Main Motor (BLDC), and it rotates clockwise for normal
feed and antic-clockwise when reverse feeding for duplex printing.* Bin Full Sensor : There is no Bin Full sensor fitted on this model.
10) Toner CartridgeThere are four toner cartridges, each containing a different colour ink : C (Cyan), M (Magenta), Y(Yellow) , and K (Black).Each one of these toner cartridge is independent and can be changed independently.
11) Fuser UnitThis unit consists of 2 Heat Lamps, 2 Heat Rollers, 2 Thermostats and a Thermistor. It melts andfuses the toner, transferred by the transfer roller onto the paper, by applying pressure and hightemperature to complete printing job.
12) LSUThis is a core part of LBP. It forms a latent image on the surface of OPC drum using a staticcharge. * Resolution: Real 600 dpi
4-5Samsung Electronics
Summary of product
Service Manual
13) Main Drive UnitThis motor drives, by way of a gearbox, the OPC unit, ITB unit, feeder unit, fuser unit, exit unit andduplex unit.> Spec.
* Power : 20W Max (24V)* Drives : OPC unit, ITB unit, Fuser, Feeder, Duplex unit, Exit unit
14) DEVE Drive UnitThis motor drives, by way of a gearbox, the toner cartridges and ITB cleaning cam.> Spec.
* Power : 20W Max (24V)* Drives : DEV (4 Color)/ITB Cleaning)
15) SMPS (Switching Mode Power Supply)This power supply uses the AC supply voltage to generate the DC voltages used by the system.The SMPS has 4 output channels (+3.3V, +5V, +24V, +24VF).The AC Heater Control Unit that supplies power to the fuser is also located on the SMPS.
16) HVPS (High Voltage Power Supply)The HVPS creates the high voltages (Charger, Supply, T1, T2, Developer) used for the electro photographic process. The high voltage is created from the 24V line from the SMPS. High Voltageoutput is supplied to the toner cartridge, OPC drum unit, ITB unit, and Transfer roller.
17) Main Controller PBAThe Main controller PBA is very important as it is the heart of printer. It has several major functionblocks.* CPU and SPGPm Block: This manages the printing order from the host, creates bitmap data for
the engine to print and controls various devices that are needed to operate the printer.*Engine Control Block: This manages images and controls various kinds of I/O* Memory Block : The operating system uses this to store video data and printing orders given by host.* ROM Block : The printer OS and PDL Interpreter are stored here.* In addition there are USB 2.0 Block, IEEE 1284 Block, Option Block, OPE Panel, etc.
18) DEVE Drive PBAEach toner cartridge requires the HV Supply only when that colour image is being processed. Thisunit takes its HV source from the HVPS and using 4 solenoids selects which cartridge is to receivethe Supply voltage. This section also contains the DEVE motor, DEVE clutch, and DEVE solenoiddrives. These are activated in sequence as required by the printing process.
19) DEVE OEM PBAThis detects new or used toner cartridges and also checks that cartridges are approved parts. If atoner cartridge is not suitable for the machine an error message is displayed.
20) Waste Toner Ass’yA cleaner blade on the OPC unit cleans waste toner from the OPC drum after every image is transferred to the ITB. Once the complete image is transferred from the ITB onto paper the ITBCleaning Solenoid activates and a cleaning blade removes waste toner from the ITB. Waste toneris transferred to the waste toner tank.The error message "Waste Toner Tank Full/ Not Install" is indicated on the LCD Panel. Replace theWaste Toner Tank immediately or the printer may be damaged
4-6
Summary of Product
Samsung ElectronicsService Manual
4.1.2 Motor & Fan Layout
Fan
1. Main Motor 2. DEVE Motor
4. Waste Toner Motor
Fan
1. Main Motor 2. DEVE Motor
4. Waste Toner Motor
NO. Name Description
1 Main Motor Drives the OPC unit, ITB unit, feeder unit, fuser unit, exit unit andduplex unit.
2. DEVE Motor Drives C, M, Y and K toner cartridges and ITB cleaning cam.
3. Fan Forces cold air into the printer and takes out heat from the fuser.
4. Waste Toner Motor Transfers collected waste toner from the OPC drum and ITB to thewaste toner tank. (Refer to front view picture on 4-2 page)
4-7Samsung Electronics
Summary of product
Service Manual
14.1.3 Clutch & Solenoid Layout
>>Solenoid
Cartridge Solenoid(C, M, Y, K)
Duplex Solenoid
ITB CleaningClutch
Black Deve Clutch
Black Deve Clutch
Yellow Deve Clutch
Magenta Deve Clutch
Cyan Deve Clutch
Cartridge Solenoid(C, K, Y, M)
Yellow Deve Clutch
Magenta Deve Clutch
Cyan Deve Clutch
T2 Home ClutchT2 Home Clutch
MP Pick_upSolenoid
MP Pick_upSolenoid
Feed RegiClutch
Pick_up Solenoid
NO. Name Description1. C DEVE solenoid Controls the High Voltage supply to the cyan cartridge.
2. K DEVE solenoid Controls the High Voltage supply to the black cartridge.
3. Y DEVE solenoid Controls the High Voltage supply to the yellow cartridge..
4. M DEVE solenoid Controls the High Voltage supply to the magenta cartridge.
5. Pick-up solenoid Controls the pick-up roller drive.
6. MP Pick-up solenoid Controls the MP pick-up roller drive.
7. Duplex solenoid When operating in duplex print mode, this reverses the directionof paper feeding to feed paper into the duplex unit.
8. T2 Home clutch This forces the transfer roller into contact with the ITB unit.
9. ITB cleaning solenoid This brings the cleaning blade into contact with the ITB unit
4-8
Summary of Product
Samsung ElectronicsService Manual
>>Clutch
NO. Name Description
1. Yellow DEVE clutch Controls Yellow color toner cartridge drive
2. Magenta DEVE clutch Controls Magenta color toner cartridge drive
3. Cyan DEVE clutch Controls Cyan color toner cartridge drive
4. Black DEVE clutch Controls Black color toner cartridge drive
5. Feed Regi. Clutch Controls the location of picked-up paper
4.1.4 Sensor & Micro S/W Layout
NO. Name Description
1. Paper Empty Sensor(FCT) This sensor detects paper in the first (main) cassette.
2. Paper Empty Sensor(SCT) This sensor detects paper in the second (optional) cassette.
3. Paper Empty Sensor(MPT) This sensor detects paper in the multi-purpose tray.
4. Feed Sensor This sensor must operate within a certain time after paper pick-
up otherwise a JAM is detected
5. ITB Home Sensor This detects the position of the image transfer belt, and in
dicates the start location for image writing. It is used to ensure
that all 4 colour images are correctly registered.
6. Waste Toner Sensor This detects whether the waste toner tank is mounted or not and
the amount of waste toner in the tank.
7. Exit Sensor This detects whether printing paper is discharged or not.
8. DEVE Cover Open S/W This detects the open/closed status of the DEVE Cover.
9. Duplex Cover Open S/W This detects the open/closed status of the Duplex Cover.
Note: * ITB Home Sensor is located in the ITB unit. If it develops a fault replace the ITB unit.* Please, refer to the Chap. 7 Arrangement and Adjustment, "Paper Path diagram", for the location
of the paper empty sensor, feed sensor, and exit sensor.* Please, refer to page 4-2 for the location of the waste toner sensor, DEVE cover open S/W, and
duplex cover open S/W.
4-9Samsung Electronics
Summary of product
Service Manual
4.1.5 Main Controller PBA
US
B
CN
24
CN
27
CN
28
CN
29
CN
30
CN
31
CN
32
CN
33
DUPLEX
CN
26T2 HO
ME
BLDC1
TH1
FUSER_FAN
SMPS
MP_EM
PT
MP SO
L
FEED
CN
25PICK_UP
CN
23CLT_FEED
CN
21EM
PT
CN
1
CN
16SCF
CN
12LSU
CN
6O
PC KEY
CN
5DEVE_DRIVERDEVE_DRIVER
CN
14LSU SW
CN
17W
ASTE TONER & EXIT
CN
15TH3
CN
4PANEL
LAN
CN
7HVPS
CN
11PTL & TH4
CN
35SO
L_ITB_CLN
CN
38BLDC2
CN
37O
EM_CO
NN
For Test
CN
10ITB
CN
9NIC
Op
tion
: NIC
4-10
Summary of Product
Samsung ElectronicsService Manual
RAM
DIM
MSPG
PmM
ain Control
FLASH M
EMO
RY
OSC
2 12MH
z(R
eserved)
OSC
112M
Hz
LPEC1
(ENG
INE C
ON
TRO
L)
OSC
323.8807368M
Hz
U36
(Counter M
emory)
4-11Samsung Electronics
Summary of product
Service Manual
USB 2.0
SDRAM
64MB
EEPROM
4k bit
Flash Memory
2MB
NPC / (W-LAN)
Optional
Full Function
Engine
Control
Block
LPEC1
SDRAM DIMM
34MB~128MB
SPGPm
Panel
16x2 LCD
5 pin UART
1) CPU BLOCKThis is the heart of the machine. A 120MHz - 32bit RISC processor is used to manage commandsand data supplied by the host. This is converted into a bitmap image which is passed to the engineblock for printing. The CPU is also used to control various other devices e.g. the USB 2.0 Interfacechip.
2) SPGPm overview
* Package- 272 pins PBGA
* Power- 1.8V(Core), 3.3V(IO) power operation- P1284 inputs : 5V tolerant
* Speed- 120MHz core(ARM946ES) operation, 60MHz bus operation- Supportable Engine Speed : under 30ppm
* Dual bus architecture for bus traffic distribution- AMBA High performance Bus (AHB)- System Bus with SDRAM
* Integrated ARM946ES- 32-bit RISC embedded processor core- 16KB instruction cache and 16KB data cache- No Tightly Coupled Memory- Memory Protection Unit & CP15 control program
4-12
Summary of Product
Samsung ElectronicsService Manual
* Direct connection up to 4 Flash ROM banks- Burst capability- Programmable timing per bank- Up to 16MB address per bank (Limited to 8MB per bank when nDREQ0 is enabled)
* Direct connection up to 6 I/O banks & 4 DMA I/O banks- Programmable timing per bank- Programmable recovery timing per bank for slow devices- Up to 16MB address per bank (Limited to 8MB per bank when nDREQ0 is enabled)
* Direct connection up to 5 SDRAM arrays- SDRAM controller supports PC-66, PC-100 and PC-133 SDRAMs running at 60MHz- Up to 128MB per array, up to 512MB totally- Wide support of various SDRAM configurations, including programmable band and column
address- Programmable SDRAM refresh time interval
* 4 General Purpose DMA controllers- Extensible architecture allows peripheral devices such as scan devices to have access to SDRAM
arrays through DMA channels- 8bits, 16bits and 32bits Data Transfer Modes are supported- IO to Memory, Memory to IO, Memory to Memory transfer support
* IEEE1284 compliant parallel port interface- Compatible ECP communications are supported- Direct support for IEEE1284 compliant data transceivers
* RSH- Fully Hardware Rotator, Scaler and Halftoner support- Variable Image Scaler and Image Halftoning Unit for PCL6- Pattern & Gamma Table Memory : 1024 x 8, 256 x 8 x 4
* Graphic Execution Unit for Banding support of Printer Languages- Support up to 256 Bit Block Transfer- Scan Line Transfer- Polygon Filling- Enhanced Graphic Order
* Compression / Decompression- CODEC : Simplified JBIG algorithm for band compression / decompression- HCT : Halftone Compression Technology (Byte Run-Length Type)- Independent use of both Codec, but enabling only one Codec is desirable for bus traffic
* UART- 3 Independent Full Duplex UART channels- Max 16 bytes FIFO to handle SIR Bit Rate Speed- DMA support for RX and TX of Channel0
* Printer Video Controller for LBP engines- 20MHz video rate are targeted- Two different kinds of Printer Video Controller (Selected by Software)
- PVC : Printer Video Controller without RET Algorithm- HPVC : Printer Video Controller with RET algorithm
(Line Memory & Lookup Table Memory : 512 x 8 , 4096 x 16)- High performance DMA based Interface to Printer Engine
- Engine Controller- Motor Control Unit
- Motor Speed Lookup Table Memory (128 x 16 x 2)- Pulse Width Modulation Unit
- 4 Channels are supported- ADC Interface Unit
- 3 ADC Channels are available- ADC Core (ADC8MUX8) maximum clock frequency : 3 MHz- Coversion time : 4.3us (@3MHz)
- LSU Interface Unit
4-13Samsung Electronics
Summary of product
Service Manual
* Timer- 3 Independent Programmable Timers- Watch Dog Timer for S/W Trap and Tone Generator for MFP Application
* Up to 5 External Interrupts support- High active interrupt signals- FIQ/IRQ Interrupt mode selectable
* Ethernet Controller (MAC)- Full compliance with IEEE standard 802.3, 802.3u specification- Support 10/100 Mbps data transfer rates- DMA engine with burst modes (4 words burst and 8 words burst are supported)
* USB 2.0 interface- USB 1.1 backward compatible- UDC(USB Device Controller) block and USB Physical block are integrated- Both of High Speed(480Mbps) and Full Speed(12Mbps) are supported- 2 DMA channels support : one RX Channel and one TX Channel- Interrupt transfer support up to 6 Endpoints- EP0 In/Out (Control transfer), EP1 In/Out (Bulk transfer), EP2 In/Out (Bulk transfer)
* Debug support- Only MultiICE logic support from ARM9 series- 5 JTAG connections : TCK, TnRST, TMS, TDI, TDO- Internal logic for synchronizing TCK and high speed CLK- Maximum TCK frequency : 20MHz (CLK x 1/6)
4-14
Summary of Product
Samsung ElectronicsService Manual
3) Memory BlockThe operating program runs from memory (see below). It is used to store video data and printingjobs from the host. Standard factory fitted memory is 64MB, and can be expanded using a DIMMmodule mounted in the SODIMM connector. This is a user fit option, DIMMs from 64Mb - 256MBcan be used giving a total of up to 320MB of memory. DIMM modules are non standard - onlySamsung product should be used.The memory controller is located in the SPGPm controls the SDRAM memory connected using a32 bit 60 MHz bus.
4) ROM BlockAn 8MB flash ROM is used to store the OS. The ROM controller is contained in the SPGPmprocessor. When initializing after power on the contents of ROM are downloaded into memory andthe OS is run from within memory.
5) USB 2.0 BlockA Netchip Co. NET2270 is used to provide support for USB2.0 and is capable of interface speedsup to 480Mbps. Under control of the SPGPm chip DMA is used to transfer incoming data directlyinto memory.
6) IEEE 1284 Block - Korea, Russia and Asia OnlyAn IEEE 1284 controller is controlled directly by the SPGPm processor. ECP mode is supported.
7) Option BlockAn Ethernet card can be attached using the 100 pin connector. It is connected directly to theSPGPm processor and communicates using a 16bit bus.
8) OPE Panel The OPE panel is controlled by a UART Block located in the SPGPm and it displays printer statusand helps the user to setup the printer. Various data is transferred using a serial interface betweena Mycom located in the OPE panel and the UART in the SPGPm.
9) MemoryThere are two types of memory, program memory that uses flash and a working memory that usesSDRAM. When printing working memory is used as band memory.
10) SensorVarious sensors are used to detect various conditions during the printing process. These includepaper empty sensor, feed sensor, exit sensor, ITB sensor, etc.
11) Actuator ControlThis section drives the various motors and clutches that are required for the paper feed and print-ing process. These include DEVE cartridge clutches (4 off), Feed Regi clutch, DEVE solenoids (4off), Pick solenoids (2 off), Duplex solenoid, ITB and T2 solenoids.
12) ADCRecognize the current of T1/T2 roll, Recognize the fusing temperature, Recognize the Waste Tonertank, Recognize the current of Waste agitator DC Motor,Recognize the OPC/ITM key, Recognizethe Developer(Y.M.C.K) key, Recognize the set temperature.
4-15Samsung Electronics
Summary of product
Service Manual
4.1.6 SMPS (Switching Mode Power Supply) PBA
The SMPS unit supplies DC power for driving the whole system, it also contains an AC heater control unitthat supplies power to the fuser.
1) DC output- Main controller PBA, OP panel, SCF, Developer driver PBA
2) AC output-Fuser unit (Heat lamp, Thermostat)
3) Output voltage
NO Item CH1 CH2 CH3 CH4
1 Channel name +3.3V +5V +24.0V +24.0VF
2 Rated outputting voltage 3.3V ± 4% +5V ± 4% +24V + 15%/-10% +24V + 15%/-10%
3 Rated outputting crrunt 2.5A 0.5A 1A 2A
4 Uses MICOM,CMOS MICOM,CMOS MOTOR,FAN MOTOR,FAN
LOGIC LOGIC
CON4
CON3
CON1 CON2
CON4
CON3
CON4
CON3
CON1 Fuse CON2
4-16
Summary of Product
Samsung ElectronicsService Manual
4.1.7 HVPS (High Voltage Power Supply) PBA
The HVPS PBA uses the 24V created by the SMPS to generate the high voltages used by the charger,supply, T1,T2 and DEVE processes. For bests quality images these high voltages must be , controlled accurately to maintain the print quality. The high voltages produced are supplied to toner,OPC cartridge, ITB unit, and transfer roller.
CHARGER (RED)T1
(BLACK)T2
(RED)
SUPPLY (BLACK)
CN1
CN2
T1 T2
SUPPLYSUPPLY
T1 T2CHARGERCHARGER
CN1CN1
CN2CN2
4-17Samsung Electronics
Summary of product
Service Manual
1) Charging Voltage: Charger* Function : This high voltage is used to charge the surface of the OPC to about -500volt~800volt.* Output voltage : -200V~-2.0KV DC +/- 3% (Duty is changeable, no loading)* Error type :If MHV was not present, the surface of the OPC is not charged. As a result, toner on
the developer roller is transferred over to the OPC drum: therefore, black paper couldbe printed out.
2) Transfer high voltage: T1(+)* Function : This high voltage is used to transfer toner from the OPC drum to the ITB unit.* Output voltage : +400V~ +3.5KV DC +/- 3% (Duty is changeable, no loading)* Error type : If T1 was not present, it is not possible to transfer toner from the OPC drum to the
ITB. As a result, printer output could be faint.
3) Transfer High Voltage: T2 (+)* Function : this high voltage is use to transfer toner from the ITB to the paper.* Output voltage : +400V~ +5KV DC +/- 3% (Duty is changeable, no loading)* Error type : If T2 was not present, it is not possible to transfer toner from the ITB to the paper. As
a result, printing output could be faint
4) Cleaning voltage: T2 (-)* This high voltage is used to transfer (-)toner, remains on transfer roller, from the Transfer Roller
to the ITB unit.* Output voltage : There is no feedback control, and it outputs a fixed voltage (-900V).* Error type : Toner contamination occurs on the reverse side of the printed-paper.
5) Supplying voltage: Supply* Function : Supply the duplicated (AC+DC) voltage from the HVPS to the Deve Drive Board.* Output voltage
AC Voltage f : 1 KHz ~ 3KHz (Duty is changeable)AC Voltage Vp-p : 1KV ~ 3KV
DC : -100V ~ -1000V
* Error type: 1. If this voltage is GND, print density is extremely low.2. If this voltage is floating due to unstable contact point at the HV terminal, density
becomes so low as that printing results are not visible to the naked eye.
4-18
Summary of Product
Samsung ElectronicsService Manual
MEMO
55
5-1Samsung Electronics
System Outline
Service Manual
5 System OutlineThis chapter describes the functions and operating principals of the main components.
5.1 CLP (Color Laser Printing) Process
5.1.1 OPC Drum Unit (Charge Section)
The OPC Unit is the image formation unit and it consists of the OPC drum, waster toner assembly, chargeroller assembly, etc. (see diagram below).
LSUEraser Lamp
Charge Bias
Waste Toner Tank
Cleaning Roller
Cleaning Blade
Charge Roller
OPC Drum
-1000V ~ -1500V
Charge Roller
HVPS
1) Structure* OPC drum: The laser light coming from the LSU forms an latent electric image on the surface of
the OPC drum.* Cleaning Blade: Removes remaining unwanted toner from the OPC drum.* Waste toner tank: Collects and stores the waste toner.* Charge roller: The charge roller is charged to a negative high voltage (-1KV~1.5KV) It is in con-
tact with the OPC drum and produces a uniform (-) voltage on its surface of approximately -500~-800V.
2) Type* Life span: 50K Images (Color 12.5K)* Waste toner removal: Transferred to a user replaceable tank* Waste tank sensors: LED type, detects tank present and tank full* OPC drum diameter: 120mm* Power: Main motor (BLDC)* Charging method: Charge roller* Eraser method: LED lamp (+5V/2Pin)* PTL: LED lamp (+5V/2Pin)
5-2
System Outline
Samsung ElectronicsService Manual
5.1.2 LSU (Exposure)The bitmap image data stream is used to switch the LSU data beam. Where white paper isrequired the beam is off, where ink is required the beam is turned on. When the laser is on and the beam strikes the OPC drum surface the charge is reduced to -50V, where the beam isswitched off the charge on the OPC surface remains at -600V. In consequence a latent image isformed on the drum surface.
-600V -600V
-50V
Reflecting MirrorPolygon Motor(30,000rpm)
Unexposed Expesed Unexposed
5-3Samsung Electronics
System Outline
Service Manual
5.1.3 Toner Cartridge (Development Section)
In the development stage toner particles are transferred from the toner cartridge onto the surface of the OPC drum. The OPC drum and the developer roller rotate in opposite directions. Toner onthe developer roller is charged to the developing voltage (-370V ± 3%). Toner is attracted to the OPC drum in those areas where the OPC drum surface charge is -50V. Toner is not attracted to those areas of the surface carrying a -600V charge.
1) Type* Developing method: Non-magnetic, Mono-component developing system.* Toner cartridge order: K, Y, M, C from top.* Developing sequence: Y, M, C, K* Life span: 7K(K) / 5K(C, M, Y)* Power: DEVE motor (BLDC)* Power transmission: Electric clutch* Dot counting method
DEV. - Black
DEV. - Yellow
DEV. - Magenta
DEV. - Cyan
DEV. - Black
DEV. - Yellow
OPC
DEV. - Magenta
DEV. - Cyan
OPCDrum
OPC
Dev Roller
DevelopingVoltage
Dev Gap
5-4
System Outline
Samsung ElectronicsService Manual
2) Developing state of colorThe page image is built up from each of the 4 colors and transferred to the paper as described below.
> Developing sequence: Y, M, C, and K
1) A latent image containing only yellow toner iscreated on the OPC drum and then transferredonto the ITB.
2) A latent image containing only magenta toneris created on the OPC drum and then trans-ferred onto the ITB to add to the yellow imagealready in the ITB.
3) A latent image containing only cyan toner iscreated on the OPC drum and then transferredonto the ITB, adding to the 2 colors alreadypresent on the ITB
4) A latent image containing only black toner iscreated on the OPC drum and then transferredonto the ITB, creating an image on the ITBconsisting of the 4 colors.
5) The Image on the ITB is secondly transferredonto paper using the T2 transfer roller.
6) The image on the page is then fused and thepaper is ejected into the output tray.
3) Toner cartridge empty detectionSoftware Dot count.
Developing and Image Transfer
Developing and Image Transfer
Developing and Image Transfer
Paper Take-up
FusingCleaning of
Image Transfer Belt
Paper Exit
Image Transfer to page
Developing and Image Transfer
Yellow ColorYellow Color
Magenta ColorMagenta Color
Cyan ColorCyan Color
Blacl BolorBlack Color
5-5Samsung Electronics
System Outline
Service Manual
5.1.4 Image Transfer Section
The toner image formed on the OPC drum is transferred to the ITB (Image Transfer Belt), this is called theprimary image transfer. When the final image has been built on the ITB it is transferred onto paper, this iscalled the secondary image transfer.
1) Structure
DUPLEXOPC DRUM
1
2
3
5
4
Paper Path
NO. Name Description
1. Image Transfer Belt Used to build up the 4 color image from the OPC drum.Colors are transferred in the order Y, M, C, K
2. Image Transfer Belt cleaner After the final image is transferred onto paper any wastetoner is removed from the transfer belt using this cleaningblade
3. PTL (Pre-Transfer Lamp) Reduce the electric potential of OPC Drum surface beforeprimary image transfer the image on the OPC Drum.
4. Image Transfer Roller (T2 Roller) This transfers the final toner image on the image transfer beltto paper.
5. ITB Home Sensor This sensor is used to ensure that each of the 4 colorimages starts at exactly the same point on the ITB. It worksby detecting a fixed point on the belt.
ITB Home Sensor
5-6
System Outline
Samsung ElectronicsService Manual
2) Primary Image TransferA colored page is split into 4 component color parts and developed one color at a time in turn onthe OPC (in the order Y, M, C, K). The final image is built up on the ITB by transferring these sepa-rate color images from the OPC drum.
DUPLEXOPC DRUM
Primary Image Transfer Bias
Image Transfer Belt
Image Transfer Roller
HVPS
3) PTL (Pre-Transfer Lamp)It is arrayed LED on PCB Board. Main function is improving the T1 utility factor by reducing theadhesive strength of OPC and Toner by irradiation on the OPC Drum formatted the image.
DUPLEXOPC DRUM
(LED)PTL
Image Transfer Belt
Image Transfer Roller
5-7Samsung Electronics
System Outline
Service Manual
4) Secondary Image TransferThe image is built up on the ITB (primary image transfer). This image is then transferred onto paperusing the T2 transfer roller (roller transfer system) this process is known as the secondary imagetransfer.
* The HVPS applies the Image Transfer Bias voltage to the Image Transfer Roller (T2), thistransfers the image from the belt onto the paper.
* When the image is to be transferred from the ITB to the paper the image transfer rollerpressure contact solenoid is activated and this activates a cam which moves the T2 rollerinto contact with the belt.
*After the transfer has taken place any remaining charge on the paper is removed byapplying a charge removal bias (generated in the HVPS) to a charge removal plate
>Type* Transfer method: Semi-conductive roller contact method* Effective transferring range: 218mm (i.e. maximum image length)
OPC DRUM Paper
Image Transfer Bias
Charge Removal Bias
Image Transfer Belt
Image Transfer Roller
HVPS
5-8
System Outline
Samsung ElectronicsService Manual
5.1.5 Fuser (Fusing Section)
Toner that has been through the primary and secondary image transfer processes is fixed, semi-permanently, to the paper.The fuser unit consists of heat lamps (2 ea), heatrollers (2 ea), thermistor, and thermostats (2 ea). Itmelts the toner onto the paper using pressure and high temperature to complete the printing process.
1) Thermostat (2pieces)If the heat lamps or heat rollers overheat thethermostat turns off power to the lamps in thefuser unit to prevent fire. It is a temperaturecut-off device.
2) ThermistorThe thermistor detects the temperature of the heat roller's surface, and feedbacks the informationto the main processor which uses this information to control power to the fuser lamps in order tomaintain the heat roller at a steady temperature.
3) Heat Roller (2pieces)Halogen lamps are used to heat the heat rollers. The heat rollers have a special Teflon surfacewhich ensures that any melted toner which comes into contact with the heat roller surface does notstick. Paper passes between the two rollers which evenly heat the paper from both sides to meltthe toner and semi-permanently fix it to the paper.
4) Safety Information> Overheat protection
* 1st level protection: Print engine is stopped if overheat is detected* 2nd level protection: Software turns off lamp power if overheat is detected.* 3rd level protection: Thermostat turns off lamp power if overheat is detected.
> Protecting device* Fuser unit power is turned off when
the duplex cover or the toner cartridge door is open.
* This machine keeps the surface temperature of the fuser unit coverunder 180°C, and it has a cautionlabel attached inside the exit coverwhere it can be easily seen by the user.
Heat Roller
Heat Roller
Heat Lamp(500W)
Heat Lamp(300W)
Paper
Spring
5-9Samsung Electronics
System Outline
Service Manual
5.1.6 ExitAfter passing through the fuser paper is ejected into the paper exit tray. Any static electrical chargeis removed by static discharge brushes.When operating in duplex print mode, after printing the front side of the page, the paper exit rollerreverses to feed the paper back into the machine in order to print the second side of the page.
5.1.7 Waste Toner Collection ProcessWaste toner on the OPC drum and on the image transfer belt is collected into the waste toner tank.* After transferring the toner image on the OPC drum to the ITB, a cleaning blade scrapes waste
toner from the OPC drum, and the waste toner is collected into a waste toner tank.* An Image Transfer Belt cleaner scrapes waste toner from the image transfer belt, and the waste
toner is collected into a waste toner tank.
1) Waste toner tank sensorA waste toner sensor detects the presence of the waste toner tank and also detects if the tank is full.This is an On / Off detection. Do not operate the printer without a waste toner tank.
> No waste toner tankWhen the waste toner tank is not installed the waste toner senoractuator blocks light from the senor LED.
> A little waste tonerWhen the sensor LED light reaches the photo sensor passingthrough the waste toner tank this indicates that the tank is not full.
> Waste toner tank fullWhen the waste toner tank is full to the level of the waste tonersensor, the senor LED light is blocked by waste toner indicating that the tank is full.
Waste Toner Sensor Actuator
Waste Toner Tank
Waste Toner Sensor
Waste Toner Tank
Waste Toner Tank
Waste Toner Sensor
Waste Toner TankWaste Toner Tank
Waste Toner Sensor
5-10
System Outline
Samsung ElectronicsService Manual
5.2 Outline of Engine Firmware
The CLP 510/510N use 4 different colored toners (Yellow, Magenta, Cyan, Black) and it is a laser colorprinter. Engine firmware controls the print processes, driving the print engine, paper feed, developer, fuser,and paper discharge systems. It has both color and mono printing modes. The printer process sequence isas follows:
System InitializationWhen power to the system is turned on all system values are initialized
Print Printer performs the actual printing job.
Post-Print The finishing state of printing job. The printer puts all systems back into a state ready to start the next job and then enters the Ready state.
Warm-Up Each part of system is activated and the system automatically checks its status and all systems are prepared to accept a job for printing.
Pre-Print As soon as a printing order is inputted from host, the printer checks the status of each part before performing the printing job.
Ready The normal state of the printer, waiting to receive a command from a host to start a job. After a predefined length of time in the Ready state if no print jobs are received the Power Save mode is entered.
5-11Samsung Electronics
System Outline
Service Manual
5.2.1 System Initialization
The system initialization process is carried out immediately after power on. The following tasks are performed.1) Initialize ASIC2) Initialize system variables3) Initialize a virtual timer4) Initialize fuser control5) Initialize ADC6) Set-up ITB HOME interrupt
5.2.2 Warm-Up
In the warm-up stage, the following tasks are performed.
1) Self Test* System error check* Cover open check* Device (ITB, OPC, DEVE cartridge) check* Heating error check* Motion of motor and jam & paper empty check* Check Feed and exit sensors. If paper is detected it is ejected. If the paper detection does not
clear a jam recovery is carried out and the paper drive unit is instructed to drive for the maximumpermitted paper length.
2) Heat ControlThe heater control unit separately manages the temperature of the heat lamps.
* Target temperature (165°C)* Temperature below 130°C - heat unit fully on,* Temperature above 135°C temperature is controlled by reading the temperature value
every 10msec.
3) CleaningTransfer rollers, OPC and ITB are electrically and mechanically cleaned.
5-12
System Outline
Samsung ElectronicsService Manual
5.2.3 Ready
1) Host interface is monitored for print commands2) Heat control
* Target temperature (165°C)* Every 40 seconds, temperature value for the previous 250ms is read and a proportional control
process is carried out3) This is the standby mode entered after warm-up or after completing a print job.4) System Error check5) Power save state is entered after timeout
> Wakeup condition* When a "wakeup" order is received* When a cover is opened and then closed* When the level of the paper empty sensor changes.
> Heat lamp is off
5.2.4 Pre-Print
This is the preparation stage before processing a printing job and after receiving a print command from a host.
1) Start LSU* Run Scanning motor* Check motor ready* Turn LD on
2) Start BLDC motor, Eraser/PTL on* Run main motor* Check lock signal* Run developer roll motor* Check lock signal
3)Turn High Voltage On* Charger on* Developer high voltage off
4) Cleaning* OPC cleaning (Mechanical motion)* ITB cleaning
5) Jam check6) Motor Unlock Check7) Check and Set a High Voltage Condition (T1, T2, Charger)8) Initialize Printing Parameters
* Paper size, copies, cassette ...* Image pixels, image times, y-offset, x-offset* Flags
9) Check Print mode* Color print mode:
- Except legal & OHP/Legal/OHP- Simplex/Duplex
* Mono pint mode: Simplex/Duplex/OHP
5-13Samsung Electronics
System Outline
Service Manual
5.2.5 Print
After sensing the ITB home position the following tasks are performed,Send Psync signal to controller -> Operates virtual timer for each color(Vdata) -> Forms latentimage on OPC drum -> Supplies toner on OPC drum -> Transfers image to ITB (T1 ) -> Pickups apaper -> Transfers image to a paper (T2)
1)Check ITB Home (Treated by Home interrupt): It is designed to detect ITB HOME every 3 seconds.a) ITB Home sensingb) If a test mode is set up, a test pattern is printed.c) A counter value is set up that addresses the timing to turn on page sync.d) The virtual timer for each color (Y, M, C, and K) is set upe) If Home is not detected every 3 seconds, an error is reported.
2)Paper path and printa) Printing paper from cassette, MPT and SCT is picked upb) Control paper path
* Stop when the leading edge of a piece of paper reaches the feed sensor.* If the leading edge doesn't reach the feed sensor, it is an error.* While transferring the last color to the ITB, re-feed the paper.* Checks if the paper reaches the exit sensor in certain time. If it reaches too soon, or it doesn't
reach, it is an error.* Checks that the paper passes the exit sensor or not.
c) Jam check* Check reaching time and passing time for the paper reaching and passing the feed and exit
sensors. If time exceeds a certain time, it is an error.d) Duplex control
* After passing the exit sensor, the duplex clutch is operated to mechanically change the directionof the paper flow in order to print the other side.
e) Printing sequence and motion for each color* Use a virtual timer for printing the colors in sequence. (Yellow, Magenta, Cyan, Black)
> What is a Virtual Timer?A virtual timer is a mathematical function for creating regular action at fixed time intervals. The stan-dard setting is for a 5msc timer interrupt.
5.2.6 Post-Print
This is the last stage of the printing process. Its functions are described below.
a) Clean transfer rollersb) Stop all virtual timersc) Initialize parameters used in the printing process.d) Stop motors
5-14
System Outline
Samsung ElectronicsService Manual
MEMO
66
6-1Samsung Electronics
Disassembly and Reassembly
Service Manual
6. Disassembly and Reassembly
6.1 Precautions When Replacing Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-2)6.1.1 Precautions when assembling and disassembling . . . . . . . . . . . . . . page(6-2)6.1.2 Precautions when handling PBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-2)
6.2 Parts for Maintenance and Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-3)6.2.1 Replacement interval for parts with a limited life . . . . . . . . . . . . . . . . page(6-3)6.2.2 Printer Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-4)
6.3 Information Related in Disassembly and Assembly . . . . . . . . . . . . . . page(6-5)6.3.1 Special Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)
1) Disassemble of LSU Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)2) Disassemble of ITB Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)3) Custody of OPC Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)4) Custody of Toner Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)5) Disassemble of DEVE Drive Ass’y and Main Drive Ass’y . . . . . page(6-5)6) Disassemble of Terminal Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)7) Disassemble of Fuser Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-5)
6.3.2 Screws Used in the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-6)6.3.3 Opening Covers and replacing Consumable parts . . . . . . . . . . . . . . page(6-7)
>> Consumable parts removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-7)6.3.4 Replacing the Waste Toner Tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-10)
>> Removing the waste toner tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-10)
6.4 Process of Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-12)6.4.1 Top Cover and Front Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-12)6.4.2 OP Panel Ass’y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-16)6.4.3 Rear Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-17)6.4.4 Duplex Cover Ass’y and Transfer Roller (T2) . . . . . . . . . . . . . . . . . . . page(6-19)6.4.5 Fuser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-21)6.4.6 Exit Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-23)6.4.7 SMPS and Main PBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-24)6.4.8 Fuser Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-27)6.4.9 Main Drive Ass’y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-28)6.4.10 HVPS (High Voltage Power Supply) . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-30)6.4.11 DEVE Drive Ass’y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-32)6.4.12 DEVE Drive PBA and DEVE Cover Open S/W . . . . . . . . . . . . . . . . page(6-34)6.4.13 DEVE Drive Motor and ITB Cleaning Solenoid . . . . . . . . . . . . . . . . page(6-36)6.4.14 DEVE Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-37)6.4.15 LSU Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-38)6.4.16 DEVE OEM PBA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-40)6.4.17 Waste Toner Ass’y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-41)6.4.18 MPT (Multi Purpose Tray) . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-43)6.4.19 Pick-Up Ass’y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-44)6.4.20 Pick-Up Roller replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . page(6-46)
6-2
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.1.1 Precautions when assembling and disassembling
* Use only approved Samsung spare parts. Ensure that part number, product name, any voltage, current ortemperature rating are correct. Failure to do so could result in damage to the machine, circuit overload,fire or electric shock.
* Do not make any unauthorized changes or additions to the printer, these could cause the printer to mal-function and create electric shock or fire hazards.
* Take care when dismantling the unit to note where each screw goes. There are 19 different screws. Use ofthe wrong screw could lead to system failure, short circuit or electric shock.
* Do not disassemble the LSU unit. Once it is disassembled dust is admitted to the mirror chamber and willseriously degrade print quality. There are no serviceable parts inside.
* Regularly check the condition of the power cord, plug and socket. Bad contacts could lead to overheatingand firfe. Damaged cables could lead to electric shock or unit malfunction.
6.1.2 Preautions when handling PBA
Static electricity can damage a PBA, always used approved anti-static precautions whenhandling or storing a PBA.
>> Precautions when moving and storing PBA1. Please keep PBA in a conductive case, anti-static bag, or wrapped in aluminum foil.2. Do not store a PBA where it is exposed to direct sunlight.
>> Precautions when replacing PBA1. Disconnect power connectors first, before disconnecting other cables2. Do not touch any soldered connections, connector terminals or other electronic parts when handling
insulated parts.
>> Precautions when checking PBA1. Before touching a PBA, please touch other grounded areas of the chassis to discharge any static elec-
trical charge on the body.2. Take care not to touch the PBA with your bare hands or metal objects as you could create a short cir-
cuit or get an electric shock. Take extra care when handling PBAs with moving parts fitted such as sen-sors, motors or lamps as they may get hot.
3. Take care when fitting, or removing, screws. Look out for hidden screws. Always ensure that the correctscrew is used and always ensure that when toothed washers are removed they are refitted in their orig-inal positions.
6.1.3 Releasing Plastic Latches
Many of the parts are held in place with plastic latches. The latches break easi-ly; release them carefully. To remove such parts, press the hook end of the latch away from the part towhich it is latched.
6.1 Precautions when replacing parts
6-3Samsung Electronics
Disassembly and Reassembly
Service Manual
6.2 Parts for Maintenance and Repair
6.2.1 Replacement interval for parts with a limited life
Some of the parts in this printer have a limited life, shorter than that of the whole machine. These parts
must be replaced periodically.
The table below shows the interval at which these parts should be replaced.
The table shows the life of each part, and is measured when using A4 paper. When servicing a machine
always check the status of these parts using the control panel and ensure that parts are replaced at the
appropriate times otherwise a general degradation in print quality will occur.
* Page: Counted value based on sides of paper printed (Duplex = 2 pages).* Image: Counted value based on printed monochrome images.* When printing a color section 1 page = 4 images. (i.e. each side is made up of 4 color images)
The life span of each of these parts is stored in memory. The amount of each 'life' used can be checked atany time using the control panel.When a part is replaced it is necessary to reset the 'life used' that is stored in memory.
* How to initialize a the value of part's life span:From the control panel, select the following items in order:Menu-Setup - Maintenance - Check other - (Select a desired part) - Reset
COMPONENT REPLACEMENT CYCLE REMARK
Toner Cartridge (Black) intial (3,000 pages@5% coverage) User replacereplacement (7,000 pages@5% coverage)
Toner Cartridge (Cyan) intial (2,000 pages@5% coverage) User replacereplacement (5,000 pages@5% coverage)
Toner Cartridge (Magenta) intial (2,000 pages@5% coverage) User replacereplacement(5,000 pagse@5% coverage)
Toner Cartridge (Yellow) intial (2,000 pages@5% coverage) User replacereplacement (5,000 pages@5% coverage)
OPC Unit mono : 50,000 pages User replacecolor : 12,500 pages
ITB Unit (T1 Roller) mono : 50,000 pages User replacecolor : 12,500 pages
Waste Toner Tank 3,000 Images User replace
Fuser Unit simplex : 100,000 pages (Mono) Engineerduplex : 50,000 pages
Transfer Roller (T2 Roller) simplex : 50,000 pages Engineerduplex : 25,000 pages
6-4
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.2.2 Printer Cleaning
A printer should be regularly cleaned, especially if it is used in a dusty environment. This will ensure thatprint quality remains high and failure due to contamination of printing services is less likely to occur.
* Clean the printer with a soft, lint free, cloth dipped in a "Recommended cleaner""Recommended cleaner" can be purchased from our service center. (where available)
* Do not touch the transfer roller when cleaning the inside of the printer. Grease and oils from theskin will contaminate the surface and reduce print quality.
* Do not touch transfer roller when cleaning inside of machine. If transfer roller gets dirty, printingquality could be low.
* Please refer to the User Manual for cleaning instructions.
6-5Samsung Electronics
Disassembly and Reassembly
Service Manual
1) Disassembly of the LSU unitThere are no serviceable parts inside theLSU. Alignment of the mirrors is critical.Opening the LSU will allow dust into thelaser and significantly reduce print quality.It is very dangerous to operate or servicea machine with the LSU open or systeminterlocks disabled. Exposure to laserradiation can cause blindness.
2) Disassembly of the ITB unitDo not disassemble the ITB. The align-ment of the home sensor is critical and isset up in the factory on a special jig.Incorrect re-assembly will cause printquality degradation.
3) Care of the OPC unitIf an OPC unit is exposed to direct sun-light for a long time the parameters andresponse of the electrostatic surface arechanged causing image transfer and printquality issues. Also there is no protectiveshutter on the OPC drum to preventscratching Please take extra care toensure the OPC drum is protected fromsunlight and physical contact when servic-ing the machine.
4) Care of the Toner cartridgeToner cartridges contain an extremely finepowder. Please keep toner cartridgesaway from children. The toner powdercontained in the toner cartridge may beharmful and if swallowed you should con-tact a doctor. Take care not to spill toner -spillages should be cleaned with avacume cleaner and washed in couldwater (hot water sets the toner). Do nottouch the developer roller surface as cont-amination will reduce print quality. Takecare not to damage the roller's surfacewhen installing or removing a toner car-tridge.
5) Disassembly of DEVE drive ass'yand the main drive ass'y
The alignment of the drive mechanism iscritical and it has been set up in factoryusing a jig and a driving gear. It is adjust-ed for the best gearing alignment. If themotor is disassembled alignment wouldnot be maintained and this could causeoperational noise and image problems:image alignment and toner distributionmay be affected.
6) Disassembly of terminal partsDo not adjust the variable resistors on thePBA. They have been already adjusted inthe factory.
7) Disassembly of the fuser unit- The fuser melts toner onto the paper at
a high temperature: therefore, you needto take special care not to get burned bya hot fuser. When removing the fuserfrom a set that has recently been operat-ing you need to take extra care.
- Do not touch an AC line (Copper con-tact) on a main frame even after remov-ing the fuser.
6.3 Information Related to Disassembly and Assembly.
6.3.1 Special service parts
Never disassemble or adjust the items mentioned, a stock of these items should be maintained.
6-6
Disassembly and Reassembly
Samsung ElectronicsTraninung Manual
6.3.2 Screws used in the printer
The screws listed in the table below are used in this printer. Please ensure that, whenyou disassemble the printer, you keep a note of which screw is used for which part andthat, when reassembling the printer, the correct screws are used in the appropriateplaces.
NO DESCRIPTION SEC CODE SPEC
S1 SCREW-MACHINE 6001-000485 2.6*4, GOLD
S2 SCREW-TAPPING 6002-000115 4*15, GOLD
S3 SCREW-TAPPING 6002-000175 3*8, GOLD
S4 SCREW-TAPTITE 6002-000308 2.6*6, GOLD
S5 SCREW-TAPTITE 6003-000119 3*8, BLACK
S6 SCREW-TAPTITE 6003-000152 2*10, GOLD
S7 SCREW-TAPTITE 6003-000179 3*6, GOLD
S8 SCREW-TAPTITE 6003-000196 3*10 SILVER
S9 SCREW-TAPTITE 6003-000266 3*6, GOLD
S10 SCREW-ASS’Y MACH 6006-001193 3*6, GOLD
NO DESCRIPTION SEC CODE SPEC
S11 SCREW-TAPTITE 6003-000269 3*6, GOLD
S12 SCREW-TAPTITE 6003-001001 3*8, BLACK
S13 SCREW-MACHINE 6001-000568 3*8, SILVER
S14 SCREW-TAPTITE 6003-001256 4*10 SILVER
S15 SCREW-TAPTITE 6003-000261 3*6, GOLD
S16 SCREW-MACHINE 6003-001068 2*16, BLACK
S17 SCREW-TAPTITE 6003-000301 4*6, GOLD
S18 SCREW-SPICIAL 6009-001396 3*10, BLACK
S19 SCREW-TAPTITE 6003-000008 4*6, SILVER
6-7Samsung Electronics
Disassembly and Reassembly
Service Manual
6.3.3 Opening Covers and replacing Consumable parts
This section shows you how to open the covers (front cover, DEVE cover, exit cover, and duplex cover) andhow to remove and replace the consumable parts (toner cartridge, ITB unit, and OPC drum).
>> Consumable parts removal
1) Pull the side handle to open the DEVE cover and then press down firmly until the toner cartridges areejected.
Caution: Before opening the exit cover, completely open the DEVE cover (eject the toner cartridges)
2) Removing a toner cartridge (K, Y, M, and C)
Caution: * Take care not to damage the rollers.* Keep the toner cartridge on a flat surface.
Pull
Black Toner Cartridge
Yellow Toner Cartridge
Margenta Toner Cartridge
Cyan Toner Cartridge
6-8
Disassembly and Reassembly
Samsung ElectronicsService Manual
3) Open the exit cover by pressing the cover open button.
Caution: Before opening the exit over completely open the DEVE cover until it is at right angles to the mainframe and the toner cartridges are ejected
4) Remove the ITB unit by releasing the ITB lock levers on both sides of the unit.
Push
Exit Cover
Deve Cover
Lever Lever
ITB Unit
6-9Samsung Electronics
Disassembly and Reassembly
Service Manual
5) Remove the OPC drum by carefully lifting the unit using the handle provided. Take care to ensure thatthe OPC drum surface is not scratched or damaged. Do not touch the surface of the drum when liftingthe drum handle or when removing the drum.
Caution: The surface of the OPC drum could be damaged if the OPC drum is exposed to direct sunlight formore than 5 minutes.
OPC Drum
6-10
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.3.4 Replacing the Waste Toner Tank
>> Removing the waste toner tank1) Push the top corners of the front cover to release the cover catches.
2) Lift the hook at the top of the waste toner tank and gently pull the top edge of the waste tank forward. Liftthe tank out.
Caution: Be careful not to let toner spill from the waste toner tank.
PUSH
PULL
6-11Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Remove the Toner Caps from the side of the tank and fit them to the tank inlets as shown below
4) Fit a new waste toner tank.
Toner Cap
6-12
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4 Disassembly Procedure
6.4.1 Top cover and Front cover
1) Remove the cassette.
2) Open all of the covers in the following order:- Duplex cover - DEVE cover - Exit cover (Refer to 6.3.3)
Cassette
Deve Cover
Exit Cover
Duplex Cover
6-13Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Release 2 screws (4*10 silver).
4) Take out the Top Cover as shown below.
Screw
Screw
Top Cover
6-14
Disassembly and Reassembly
Samsung ElectronicsService Manual
5) Push both of the top corners to release the catches and open the front cover and then remove the wastetoner tank. (Refer to 6.3.4)
6) Lift the hook at the top of the waste toner tank and gently pull the top edge of the waste tank forward. Liftthe tank out.
Caution: Remember to fit the Toner Caps.
PUSH
6-15Samsung Electronics
Disassembly and Reassembly
Service Manual
7) Release 7 screws (3*10 silver) located inside the front cover.Release 2 screws (3*10 silver) located on the top of the front cover.
8) Release 2 hooks on the right and the left side with a flat bladed screwdriver and then remove the frontcover. Take care to disconnect one harness connected to the frame.
Hook Hook
Screw Screw Screw Screw
ScrewScrew
Screw
Screw Screw
6-16
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.2 OP Panel Ass’y
>> Before disassembling it: Remove the front cover. (Refer to 6.4.1)
1) Release 4 screws ('A' below 3X8 gold) and take out the OP panel ass'y (Panel PBA).
2) Release 7 screws ('B' below 3X8 black) from the Panel PBA and remove the panel PBA.
3) Release 1 screws ('C' below M2.6X6 gold) from the LCD and then take out the LCD.
A : OP Panel Screw, 3 X 8 Gold (4EA)B : Panel PBA Screw, 3 X 8 Black (7EA)C : LCD Screw, M2.6 X 6 Gold (1EA)
ScrewScrew Screw
Screw
Screw
Screw
Screw
Screw Screw
Screw
Screw
Screw
BB BB
BB BBAA
AA AAAABB
CC
6-17Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.3 Rear Cover
>> Before disassembling it: *Open the duplex cover, the DEVE cover and the exit cover. (Refer to 6.3.3)Remove the top cover. (Refer to 6.4.1)
1) 1) Remove 10 screws.A: Top 2 EA (3 * 10 Silver)B: Side 3 EA (3 * 10 Silver)C: Bottom 3 EA (4 * 10 Silver)D: Rear 2 EA (3 * 10 Silver)E: NPC(If fitted) 2EA(3 * 10 Silver)
Screw
Screw
Screw Screw
ScrewScrew
Screw
Screw
Screw
Screw
Screw Screw
A
D
C
B
A
D
C
B
EE
6-18
Disassembly and Reassembly
Samsung ElectronicsService Manual
2) Take out the Rear Cover as shown below.
6-19Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.4 Duplex Cover Ass'y and Transfer Roller (T2)
>> Before disassembling it: * Open the duplex cover, the DEVE cover and the exit cover. (Refer to 6.3.3)* Remove the front cover and top cover. (Refer to 6.4.1)* Remove the rear cover. (Refer to 6.4.3)1)
1) Release 2 hinge screws (3*10 silver) - one on each side of the duplex unit.
2) Remove the duplex cover ass'y by pulling it in the direction shown by the arrows in A and B below.* A: Lift up the left side section.* B: Remove the duplex cover ass'y by pulling the right side section towards the left.
Screw
Duplex Ass’y
AA
BB
6-20
Disassembly and Reassembly
Samsung ElectronicsService Manual
3) Release 4 hooks on the right and left side with a flat bladed screwdriver and then remove the duplexass'y.
4) Remove the transfer roller by turning the bush on each end of the roller
Duplex Ass’y
Hook
Hook
Hook
Hook
Duplex Ass’y
Transfer Roller
6-21Samsung Electronics
Disassembly and Reassembly
Service Manual6-21
Samsung Electronics
Disassembly and Reassembly
6.4.5 Fuser
1) Open the DEVE cover
Caution: Before opening the exit cover, completely open the DEVE cover until it is at right angles to themain frame and the toner cartridges are ejected
2) Open the exit cover.
Pull
Push
Exit Cover
Deve Cover
6-22
Disassembly and Reassembly
Samsung ElectronicsService Manual
3) Release 5 screws (3*10 silver) and then remove the harness cover.
4) Remove one harness.
5) Remove the fuser by holding both sides of the fuser and then pulling the fuser upwards.
Harness Cover
Screw
ScrewScrew
Screw
Screw
Harness
6-23Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.6 Exit Cover
>> Before disassembling it: * Remove the front cover (Refer to 6.4.1)* Remove the rear cover (Refer to 6.4.3)* Remove the duplex cover (Refer to 6.4.4)* Remove the fuser (Refer to 6.4.5)
1) Support the Exit Cover and remove the 2 screws (4*10 Silver) indicated using a long blade screwdriverfrom inside the OPC cavity. Remove the Exit Cover.
2) Remove the exit cover.
ScrewScrew
ScrewScrew
6-24
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.7 SMPS and Main PBA
>> Before disassembling it*Remove the rear cover (Refer to 6.4.3)
1) Release 5 screws (3*6 machine screw, gold) from the main PBA bracket.
Main PBA Bracket
Screw
Screw
Screw
Screw
Screw
6-25Samsung Electronics
Disassembly and Reassembly
Service Manual
2) Release 4 screws from the SMPS.Release one screw (3*10 silver) from the harness guide.
A: Right side 2EA (3 * 6 Gold)B: Left side 1EA (3 * 10 Silver)C: Bottom 1EA (4 * 10 Silver)
3) Remove 4 harnesses from the SMPS.
Screw
Screw
Screw
SMPS A
C
AScrewBB
C
A
CON4
CON3 CON4
CON3
CON4
CON3
CON1CON1 Fuse
CON2CON2
6-26
Disassembly and Reassembly
Samsung ElectronicsService Manual
4) Remove all harness connected to the main PBA.
5) Release 5 screws (3*6 machine screw, gold) from the main PBA and then remove the main PBA.
6) When replacing the Main PBA the Counter memory chip (U36) must be transferred to the new PBA.
USB
CN24
CN27
CN28
CN29
CN30
CN31
CN32
CN33
DUPLEX
CN26T2 HOME
BLDC1
TH1
FUSER_FAN
SMPS
MP_EMPT
MP SOL
FEED
CN25PICK_UP
CN23CLT_FEED
CN21EMPT
CN1
CN16 SCF CN12 LSU
CN6 OPC KEY
CN5 DEVE_DRIVERDEVE_DRIVER
CN14 LSU SW
CN17WASTE TONER & EXIT
CN15TH3
CN4 PANEL
LAN
CN7 HVPSCN11 PTL & TH4
CN35 SOL_ITB_CLN
CN38 BLDC2
CN37 OEM_CONN
For Test
CN10 ITB
CN9 NIC Option : NIC
Screw
Screw
Screw
Main PBA
Screw
Counter Memory
Screw
6-27Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.8 Fuser Fan
>> Before disassembling it: * Remove the top cover (Refer to 6.4.1)* Remove the rear cover (Refer to 6.4.3)* Remove the main PBA bracket. (Refer to 6.4.7)
1) Release 3 screws (3*10 silver) remove one harness from the main PBA and then take out the fuser fan.
Fuser Fan
Screw
Screw
Screw
6-28
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.9 Main Drive Ass’y
>>Before disassembling it: * Remove the rear cover (Refer to 6.4.3)* Remove the fuser (Refer to 6.4.5)* Remove the SMPS (Refer to 6.4.7)* Remove the fuser fan (Refer to 6.4.8)
1) Remove all harnesses from the harness guides.
3) Look inside the OPC drum cavity and locate the T2 cam. Remove the washer using tweezers and thenremove the T2 cam.
Cam-Drive
Washer-Plain
6-29Samsung Electronics
Disassembly and Reassembly
Service Manual
4) Remove the washer using tweezers and then remove the OPC gear and pin. (The OPC gear can befound inside the printer after removing the OPC drum unit. Take care that the pin is not lost as youremove the gear.)
5) Remove the motor harness.Release 5 screws (3*10 silver) and then take out the main drive ass'y.
Gear-Drive
Pin-Drive
Washer-Plain
Screw
Screw
Screw
Harness
Screw
Screw
Caution : Please don’t lose the Pin-Drive
6-30
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.10 HVPS (High Voltage Power Supply)
>>Before disassembling it: * Disassemble the front cover & top cover (Refer to 6.4.1)* Disassemble the rear cover (Refer to 6.4.3)* Disassemble the main PBA bracket (Refer to 6.4.7.)
1) Remove one harness from the main PBA
2) Remove one harness and 4 high-voltage harnesses from the HVPS.
USB
CN7 HVPS
SUPPLY
T1 T2CHARGER
CN1(to Deve Driver)
Harness
RedRed
BlackBlack
Harness
Harness
RedRedBlackBlack
<Main PBA> <HVPS>
6-31Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Remove 5 screws (3*6 machine screw, silver) and then remove the HVPS.
Screw
Screw Screw
Screw
Screw
6-32
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.11 Deve drive ass’y
>>Before disassembling it: * Disassemble the rear cover (Refer to 6.4.3)* Disassemble the main PBA (Refer to 6.4.7)
1) Remove the main PBA shield and harness guide by releasing 5 screws (2 EA 3*6 machine screw, gold: 1 EA 3*10 silver, 1 EA 4*10 silver)
2) Remove the ground harness and the harness guide bracket by releasing 3 screws (2 EA 3*6 machine screw, gold: 1 EA 4*10 silver).
Harness Guider
Main PBA Shield
Screw
Screw
3 x 6 Gold
4 x 10 Silver
3 x10 SilverScrew
Screw
3 x 6 Gold
Guide Harness Bracket
Screw Screw
Screw
Screw
4 x 10 Silver4 x 10 Silver
4 x 10 Silver4 x 10 Silver
Ground Harness
6-33Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Separate the harness from the DEVE motor.
4) Release 5 screws (3*10 silver) from the DEVE drive ass'y.Remove 4 harnesses connected to the DEVE drive PBA and then remove the DEVE drive ass'y.
Motor Harness
Screw
Screw
Screw
Screw
ScrewHarness
SUPPLY
CN5 CLT_4TH
CN9 CLT_3RD
CN4 CLT-2ND CN8 CLT-1ST
6-34
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.12 Deve drive PBA and DEVE cover open S/W
>>Before disassembling it: * Disassemble the rear cover (Refer to 6.4.3)* Disassemble the main PBA (Refer to 6.4.7)* Disassemble the main PBA bracket (Refer to 6.4.7.2)
1) Release 1 screw (3*10 silver) and then take out the DEVE cover open S/W.
2) Remove all harnesses and 6 screws (3*10 silver) and then take out the DEVE drive PBA.
Deve Cover Open S/W
Screw
Screw
Screw
Screw
Screw
Screw
Screw
SUPPLY
CN1
CN2 SOL-2ND
CN7 SOL-3RD
CN1 BLCD_DEV
CN6 SOL_1ST
CN3 SOL_4TH
CN5 CLT_4TH
CN9 CLT_3RD
CN4 CLT-2ND CN8 CLT-1ST
6-35Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Remove 4 high-voltage terminals.
Terminal
Terminal
Terminal
Terminal
6-36
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.13 Deve Drive Motor ITB Cleaning Solenoid
>>Before disassembling it: * Disassemble the rear cover (Refer to 6.4.3)* Disassemble the main PBA (Refer to 6.4.7)* Disassemble the main PBA bracket (Refer to 6.4.7)* Disassemble the DEVE drive motor. (Refer to 6.4.7)
1) Release 4 screws (3*6 gold) and then remove the DEVE drive motor.
2) Unplug one harness from the DEVE drive PBA and then remove the ITB cleaning solenoid.
Screw
Screw
Screw
Screw
ITB Solenoid
6-37Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.14 DEVE cover
>> Before disassembling it: * Remove all consumption parts (Toner cartridge, ITB unit, and OPC drum) (Refer to 6.3.3)* Disassemble the front cover and top cover (Refer to 6.4.1)* Disassemble the LSU cover. (Refer to 6.4.14)
1) Remove 2 screws (3*10 silver) and then remove the DEVE open link guide.
2) Separate the DEVE cover by pulling it in the direction of the arrow.
Deve Open Link
Screw
Screw
Deve Open Link Guide
Deve Cover
6-38
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.15 LSU unit
>> Before disassembling it: * Remove the consumable parts (Toner cartridge, ITB unit, and OPC drum) (Refer to 6.3.3)* Disassemble the Deve cover. (Refer to 6.4.15)
1) Release 4 screws (4*10 silver). (Use a short length cross-head screwdriver.)
Caution : When removing the 4 screws labeled “A” you will need to use a short screwdriver.
2) Release one screw (3*8 yellow). (Use a short length cross-head screwdriver.)
Screw
ScrewScrew
Screw
AA
AA AA
AA
Screw
LSU GroundLSU GroundLSU Ground
6-39Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Separate 2 harnesses and remove the LSU unit.
HarnessHarness
6-40
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.16 DEVE OEM PBA
>> Before disassembling it: * Disassemble the front cover and the top cover. (Refer to 6.4.1)* Remove the Rear Cover (Refer to 6.4.3)* Disassemble the Main PBA Bracket (Refer to 6.4.7)
1) Separate one harness (CN1) from the Main PBA and one harness(CN2) from the DEVE OEM PBA.Remove 6 screws (3*8 black) and then take out the DEVE OEM PBA.
2) Remove 12 terminals.
Deve OEM PBA
Screw
Screw
Screw
Screw
Screw
Screw
Harness
Terminals
6-41Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.17 Waste toner ass’y
>> Before disassembling it: * Disassemble a front cover and a top cover. (Refer to 6.4.1)
1) Release 6 screws (3*10 silver).* Upper part: 4 screws * Lower part: 2 screws
2) Remove the waste toner ass'y by first reaching into the OPC cavity and lightly depressing the wastetoner receiver whilst at the same time gently pulling the waste toner motor assy away from the set. Oncethe ass'y is released refer to the photograph and remove the ass'y.
Caution: * It is very likely that waste toner will be spilled when removing the waste toner ass'y.
Screw
Screw
Screw
Screw
Screw
Screw
OPC Lifter
6-42
Disassembly and Reassembly
Samsung ElectronicsService Manual
3) Release one screw (3*10 silver) and then remove the sensor cover.
Screw
6-43Samsung Electronics
Disassembly and Reassembly
Service Manual
6.4.18 MPT(Multi Purpose Tray)
>> Before disassembling it: * Disassemble all consumable parts (Toner cartridge, ITB unit, and OPC drum) (Refer to 6.3.3)* Disassemble the front cover and top cover (Refer to 6.4.1)* Disassemble the rear cover. (Refer to 6.4.3)* Disassemble the duplex cover. (Refer to 6.4.4)* Disassemble the SMPS & main PBA. (Refer to 6.4.7)
1) Release 4 screws (3*10 silver)
2) Release the 2 clips located underneath the machine (see photograph). Pull the MP Ass'y upward andremove
Screw Screw
Screw Screw
Snap -Fit Snap -Fit
6-44
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.19 Pick-UpAss'y
>> Before disassembling it: *Disassemble all consumable parts (Toner cartridges, ITB unit and OPC drum) (Refer to 6.3.3)*Disassemble the front cover and top cover (Refer to 6.4.1)*Disassemble the rear cover. (Refer to 6.4.3)*Disassemble the duplex cover. (Refer to 6.4.4)*Disassemble the SMPS & main PBA. (Refer to 6.4.7)*Disassemble the Erase Lamp. (Refer to 6.4.14)*Disassemble the Waster Toner Ass'y (Refer to 6.4.18)
1) Undo 2 screws (3*10 silver) and remove the “Pick-up Solenoid”. Then remove the plastic circlip whichretains the Pick-Up Gear and also remove the gear wheel. Release the shaft retaining bearing.
2) Remove the 3 screws (4*10 silver) in the “Pick-up Ass’y”
Screw
Screw
Pick-Up Solenoid
Screw
Screw
Screw
Pick-Up Ass’y
6-45Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Remove the 3*8 black screw retaining the Guide Pick-Up plate. Using a small flat bladed screwdriver orsimilar tool force the brass ground plate off the retaining lugs and bend it upward slightly. Release theEraser Lamp harness and paper Empty Sensor harness, these pass between the main engine frame andbase frame and cannot be removed.
4) Remove the “ACTUATOR-EMPY (JC72-00465A)” sensor arm and then take out the “Pick-up Ass’y” bylifting the right hand side and sliding the shaft from the frame.
Screw
Ground Feed
Guide Pick-Up Plate
6-46
Disassembly and Reassembly
Samsung ElectronicsService Manual
6.4.20 Pick-Up Roller replacement
Note It is not necessary to remove the Pick Up Assy in order to replace the Pick Up Roller
>> Before disassembling it: *Disassemble all consumable parts (Toner cartridges, ITB unit, Waste Toner Collector and OPCdrum) (Refer to 6.3.3)
*Disassemble the rear cover. (Refer to 6.4.3)*Disassemble the SMPS (Refer to 6.4.7)
1) Undo 2 screws (3*10 silver) and remove the "Pick-up Solenoid". Then remove the plastic circlip whichretains the Pick-Up Gear and also remove the gear wheel. Release the shaft retaining bearing andremove it.
2) Remove the paper cassette. Use a vacume cleaner to remove any waste toner from the Waste Tonercollectors inside the OPC space.
Waste TonerCollectorsWaste TonerCollectors
6-47Samsung Electronics
Disassembly and Reassembly
Service Manual
3) Turn the set upside down and Release the shaft retaining bearing and slid it away from the roller.Release the Pick Up spring.
4) Push the rollers firmly towards the frame, if necessary rotate the shaft so that the rubbers do not contactthe frame. Release the shaft and bush from the end support. Note this support is fragile take great care.Then slide the shaft back away from the frame to remove it.
A Shaft retaining bearingA Shaft retaining bearing
C. Bush and SupportC. Bush and Support
B. SpringB. Spring
6-48
Disassembly and Reassembly
Samsung ElectronicsService Manual
MEMO
77
7-1Samsung Electronics
Alignment & Adjustments
Service Manual
7. Alignment and Adjustments
This chapter describes some of the main service procedures including:Using the EDC mode; Clearing paper jam and test patterns.Much of this chapter is also included in the user's guide.
7.1. Paper path and Paper jam
7.1.1 Paper path
DEV. - Black
DEV. - Yellow
Pick-upRoller
DEV. - Magenta
DEV. - Cyan
CASSETTE
Feeder
DUPLEX
Fuser Unit
EXIT Ass’y
MPF Path
Duplex PathDuplex Path
MPF
MPT
DEV. - Black
DEV. - YellowOPCOPC
DEV. - Magenta
DEV. - Cyan
SCFSCF
FCF
ITBITB
Feeder
DUPLEX
Fuser Unit
EXIT Unit
SCF Path
Transfer Roller
Exit Sensor
Paper Pick-Up RollerPaper Empty Sensor(FCT)
Paper Empty Sensor(SCT)
Paper Empty Sensor(MPT)
Feed Sensor
SCT Path
FCT Path
MPT Path
7-2
Alignment & Adjustments
Samsung ElectronicsService Manual
7.1.2 Jams
1) Jam0 (Jam in feed area)
* After a page was picked up, it was not fed.* Paper does not reach the feed sensor in a
certain time.* Feed sensor is faulty and does not detect
paper.- FCF pickup error: When a paper is not
picked up in the 1st cassette.- SCF pickup error: When a paper is not
picked up in the 2nd cassette.
2) Jam1 (Jam inside printer)
* After the leading edge of the paper hasreached the feed sensor, the feed sensordoesn't turn off (fails to detect the trailing edgeof the paper) in a certain time
* After the leading edge of the paper has passed the feed sensor, it doesn't reach theexit sensor in a certain time.
* Exit senor is faulty and does not detect paper.
3) Jam2 (Jam in exit area)
* After the leading edge of the paper haspassed, the trailing edge of the paper has notpassed the exit sensor within a certain time
* The paper drive motor has been driving forlonger than the time needed for the longestpaper size and the exit sensor is not off.
Pick-upRoller
Feed Sensor
Paper Empty Sensor
Exit Sensor
Feed Sensor
Exit Sensor
7-3Samsung Electronics
Alignment & Adjustments
Service Manual
4) Jam duplex (Jam in duplex area)
* Jam duplex occurs when printing the reverseside of the paper during duplex printing. Afterprinting the front side the duplex solenoid mustoperate in order to feed the paper back into theduplex path. If the solenoid fails paper may bestuck in the exit roller and is not fully electedinto the exit tray
* If the duplex solenoid operates paper is fedback into the machine. If the leading edge ofthe paper does not reach the feed sensor in acertain time then Jam Duplex occurs.- This can be cause by paper being jammed
in the duplex path area.
5) Jam MPF
* Paper could not be picked up from the MPF tray.* After pickup, a paper has been fed, but it
doesn't reach the feed sensor in a certain time.* Feed sensor is faulty and does not detect paper.
Exit Sensor
Feed Sensor
CASSETTE
SCF
SCF Path
MP Empty Sensor
Feed Sensor
7-4
Alignment & Adjustments
Samsung ElectronicsService Manual
7.2 Jam Removal
When a jam occurs while printing a jam message is displayed on the control panel.
* Jam0 In Tray 1:Paper jam in the main cassette.
* Jam0 In MP Tray: Paper jam in the MP tray
* Jam0 Tray2:Paper jam in the SCT (Second cassette tray)
* Jam Inside Printer: Jam 1, Paper is jammed inside the printer.
* Jam In Exit Area: Jam2, Paper is jammed in the exit area when ejecting paper.
* Jam In Duplex Path: While duplex printing, paper is jammed in the duplex unit.
CAUTION: When removing jammed paper, always pull it firmly and evenly without any sudden jerks. If at all possible, remove the paper as a single sheet. If the paper tears ensures ALL paper fragments are removed. Any fragments left inside the machine will cause it to jam again.
7.2.1 Factors that cause paper to jam
- Too much paper is loaded in the cassette.- Paper in not loaded correctly in the cassette.- Duplex cover opened while printing.- Cassette removed while printing.- Incorrect thickness of paper used.- Incorrect size of paper used.- Cassette paper guides not correctly set (loose or too tight).- Foreign object or other contamination of internal paper path and paper guide ribs.- Badly damaged or folded leading or trailing edges of the paper.
7-5Samsung Electronics
Alignment & Adjustments
Service Manual
7.2.2 Tips for Avoiding Paper Jams
By selecting the correct paper types, most paper jams can be avoided. If a paper jam occurs, follow thesteps outlined below:
• Ensure that the adjustable guides are positioned correctly.
• Do not overload the tray. Ensure that the paper is below the paper capacity mark on the right
inside the tray.
7.2.3 Jam 0 In Tray 1
If paper is jammed in the paper feed area,'Jam0 In Tray1 ' appears on the display.
1. Using the handle open the right cover.
2. Carefully remove the misfed paper in the direction as shown.
3. Close the right cover .The printer resumes printing.
4. Pull the tray open. After you pull it all the wayout lift up the front part of the tray slightly torelease the tray from the machine.
5. Remove the jammed paper by gently pulling itstraight out.
6. To replace the tray lower the rear edge, align itto the slot and slide it into the printer.
7. Close the right cover .The printer resumes print-ing.
If there is any resistance, and the paperdoes not move immediately when you pull,stop pulling and go to step 4.
7-6
Alignment & Adjustments
Samsung ElectronicsService Manual
1. If the paper is not feeding properly pull thepaper out of the machine..
2. To resume printing, open and close the rightcover.
7.2.4 Jam 0 in MP Tray 1
'Jam0 In MP Tray' appears on the display when you are printing using the Multi-purpose Tray and the print-er detects either there is no paper or the paper is improperly loaded.
1. Using the handle open the right cover. 2. Remove the jammed paper in the directionshown. To avoid the paper tearing pull it outgently and slowly.
3.Close the right cover. The printer resumes printing.
7.2.5 Jam Inside Printer : Jam1
‘If paper is jammed inside the printer 'Jam Inside Printer' appears on the display.
NOTE : If the paper tears make sure thatall of the paper fragments areremoved from the printer.
7-7Samsung Electronics
Alignment & Adjustments
Service Manual
7.2.6 Jam In Exit Area : Jam2
If paper is jammed in the paper exit area 'Jam In Exit Area ' appears on the display.
1. If a long portion of the paper is visible pull itstraight out. If not continue to step 2.
2. Using the handle open the left cover completely.
3. Press the top cover release button to unlatchthe top cover and open it all the way.
4. Carefully take the jammed paper out of theprinter.
5. Close the top cover and the left cover firmly
6. Open and close the right cover to resume printing.
CAUTION : If the left cover is not completelyopen the top cover release buttonwill not press.
Fuser
CAUTION : Do not touch the fuser it is hot andcould cause burns! The fuser's operating temperature is 180 °C (356 °F). Take care when removingpaper from the machine.
CAUTION : Do not try to close the top cover withthe left cover closed. This may causedamage to the machine.
7-8
Alignment & Adjustments
Samsung ElectronicsService Manual
7.2.7 Jam In Duplex Path : Jam Duplex
If paper is jammed in the duplex area 'Jam In Duplex Path' appears on the display.
1. Using the handle open the right cover.
2. Locate the jammed paper and then pull it outgently and slowly to avoid the paper tearing.Close the right cover. The printer resumes print-ing.
or
3. If you cannot find the jammed paper or there isany resistance removing the paper go to step 4.
4. Using the handle open the left cover completely.
5. Press the top cover release button to unlatchthe top cover and open it all the way.
CAUTION : If the left cover is not completelyopen the top cover release buttonwill not press.
Note : If the paper tears make sure that all of thepaper fragments are removed from theprinter.
7-9Samsung Electronics
Alignment & Adjustments
Service Manual
6. Locate the jammed paper and then carefullytake it out of the printer.
7. Close the top cover and the left cover firmly
Fuser
CAUTION : Do not touch the fuser it is hot andcould cause burns! The fuser's operating temperature is 180 °C(356 °F). Take care when removingpaper from the machine.
CAUTION : Do not try to close the top cover with the left cover closed. This maycause damage to the machine.
7-10
Alignment & Adjustments
Samsung ElectronicsService Manual
7.2.8 Jam In the Optional Second Tray
1. Using the handle open the right cover.
2. Remove the jammed paper in the directionshown. To avoid the paper tearing pull it outgently and slowly.
3. Close the right cover. The printer resumes printing.
4. If you cannot find the jammed paper in themachine open the Tray2 outer jam cover.
5. Open the inner cover of Tray 2.
6. Pull the jammed paper out in the directionshown. To avoid the paper tearing pull it outgently and slowly. If there is any resistance, andpaper does not move immediately when youpull, stop pulling and continue to step 8.
7-11Samsung Electronics
Alignment & Adjustments
Service Manual
7. Close the two jam covers. Go to step 11.
8.Pull the optional tray, Tray 2, out of the printer.
9. If you see the jammed paper remove the paperfrom the machine by gently pulling it straight out.
10. Slide the tray back into the printer and closethe two jam covers.
11. Open and close the right cover. The printerresumes printing.
7-12
Alignment & Adjustments
Samsung ElectronicsService Manual
7.3 Sample Pattern
This product provides several printable test patterns for maintenance purposes. These patterns can be used to aid the diagnosis of print quality problems.
7.3.1 Printing a Demo PagePrint a demo page to make sure that the printer is operating correctly.
1. Press the Menu button on the control panel until you see “Information ” on the bottom line of the display..
2. Press the Enter button to access the Menu.
3. Press the scroll button until you see “Demo Page ” on the bottom line.
4. Press the Enter button .
A demo page showing the printer ’s features and capabilities prints out.
7.3.2 Printing a Configuration PagePrint a demo page to make sure that the printer is operating correctly.
1. Press the Menu button on the control panel until you see “Information ” on the bottom line of the display..
2. Press the Enter button to access the Menu.
3. Press the scroll button until you see “Configuration ” on the bottom line.
4. Press the Enter button .
A demo page showing the printer ’s features and capabilities prints out.
7.4 Checking the Remaining Toner and Others
7.4.1 Checking the Remaining TonerYou can check the level of toner left in each cartridge.
1. In ready mode press the Menu button on the control panel several times until you see ‘Setup ’on the bottom line
of the display.
2 Press the Enter button to access the menu.
3 Press the scroll button until ‘Maintenance ’ displays on the bottom line.
4 Press the Enter button
5 When ‘Check Toner ’ displays on the bottom line,,press the Enter button .
6 Press the scroll button until the color of the toner cartridge you want to check displays on the bottom line.
7 Press the Enter button The display shows the percentage of the remaining toner.
8. Press the Upper Level button to return to step 6 and select a different cartridge.
9. To return to the Ready condition press the Upper Level button several times until 'Ready' appears in the display
7.4.2 Checking the Remaining OthersYou can check the level of each item.
1. In ready mode press the Menu button on the control panel everal times until you see ‘Setup ’on the bottom line
of the display.
2 Press the Enter button to access the menu.
3 Press the scroll button until ‘Maintenance ’ displays on the bottom line.
4 Press the Enter button
5 When ‘Check Others ’ displays on the bottom line,,press the Enter button .
6 Press the scroll button until the item you want to check displays on the bottom line.
7 Press the Enter button The display shows the percentage of item.
8. Press the scroll button display either 'Image Count' or 'Reset'
9a. Choose 'Reset' and press enter to reset the counter after replacing a consumable item
or
9b Choose Image count to display the counter.
10. Press the Upper Level button to return to step 7 and select a different choice or press it a second time to return to step
6 and choose a different item.
11. To return to the Ready condition press the Upper Level button several times until 'Ready' appears in the display.
7-13Samsung Electronics
Alignment & Adjustments
Service Manual
7-14
Alignment & Adjustments
Samsung ElectronicsTraninung Manual
7.5 Understanding the Control Panel
The control panel on the top right side of your printer has a display and seven buttons.
7.5.1 Display
Buttorns
Status Map Display : dispaly the printerstatus and job in progress.
Message Description
Ready •The printer is on-line and ready to print.
•If you press On Line/Continue ,the printer switches to off-line.
Offline •The printer is off-line and cannot print.
•If you press On Line/Continue ,the printer switches to on-line.
Processing... •The printer is printing.
•If you want to cancel printing,press Cancel .
Sleeping... •The printer is in Power Save mode, using less power.When a print job is
received from the computer or if any button is pressed,the printer switches to
on-line.
•To deactivate the Power Save mode or change the power-saving time.
7-15Samsung Electronics
Alignment & Adjustments
Service Manual
Message Description
When an error occurs,a lamp turns on at the corresponding location on the Status map.An error
message appears on the display so that you can locate the error.
•Press to switch between on-line and off-line.
•In menu mode,press to return to ready mode.
The color of the On Line/Continue button indicates the status of the printer.
• Press to enter menu mode.
• In menu mode,press to scroll through the menus.
In menu mode,press to select the displayed submenu item or confirm the changed setting.The
selected item is marked with an *.
In menu mode,press to scroll through submenu items or setting options.Pressing • moves you to
the next option and pressing • sends you back to the previous option.
• Press to cancel the current print job.
• In menu mode,press to return to ready mode.
In menu mode,press to go back to the upper menu level.
•The printer is off-line and cannot print.
•The printer is in Power Save mode. When data is received,it switches to on-line.
Green
Orange
Off
On
Blanking
On
Blanking
Status map
The printer is on-line and can receive data from the computer.
• When the backlight blinks slowly,the printer is receiving data from
the computer.
• When the backlight blinks quickly,the printer is receiving and print-
ing data.
The printer stops printing due to a major error.Check the display
message.
A minor error has occured and the printer is waiting for the error to
be cleared.Check the display message.When the problem is
cleared,the printer resumes printing.If you want to ignore this warn-
ing,press this button.
7.5.2 Buttons
7-16
Alignment & Adjustments
Samsung ElectronicsService Manual
7.5.3 Using Control Panel Menus
A number of menus are available to make it easy for you to change the printer settings.
You can configure your printer from the printer’s control panel.You can also use the control panel menus while the printer
is in use.
1. In ready mode press the Menu button until you see the menu you want on the bottom line of the display.
2. Press the Enter button to access the menu.
3. Press the scroll button until the menu item you want displays on the bottom line.
4. Press the Enter button to confirm the selected item.
5. If the menu item has submenus, repeat steps 3 and 4.
6. Press the scroll button until the setting option you want displays on the bottom line or enter the required value.
7. Press the Enter button to save your input or selection.
- An asterisk (*) appears next to the selection on the display, indicating that it is now the default.
8. To exit the menu, press the Upper Level button repeatedly, or the Cancel button .
- After 60 seconds of inactivity (no key has been pressed), the printer automatically returns to ready mode.
NOTE: Print settings made from the printer driver override the settings on the control panel.
Information Paper Layout Graphics Printer
Configuration Tray Source Orientation
Resolution Default Set
Menu Map Media Size Duplex Current Job
Demo Page Width Duplex Margin
PS3 Font List Custom
Custom
Height Simplex Margin
PCL Font List Media Type Copies
Network PostScript PCL Setup Color
Config. Network Print PS Error Typeface LCD Language Calibration
Reset Network
Symbol
Emulation
Custom Color
Default Set Lines Power Save
Print Net CFG Pitch Auto Continue
Jam Recovery
Altitude Adj.
Auto CR
Job Time Out
Maintenance
7-17Samsung Electronics
Alignment & Adjustments
Service Manual
7.6 Periodic Defective Image
If an image defects appears at regular intervals on the printed-paper, it is due to a faulty or damaged roller.Refer to the table below and check the condition of the appropriate roller.
No Roller Defective image Typical defect
1 OPC Drum same position in each page white spot on black image or black spot
2 Charge Roller 43.96 mm black spot
3 Supply Roller 31.41 mm light or dark horizontal image band
4 Developing Roller 35.34 mm horizontal image band
5 ITB(T1) same position in each page black spot
6 Transfer Roller(T2) 75.36 mm ghost
7 Heat Roller 109.9 mm Black spot and ghost, printing backside pollution
7-18
Alignment & Adjustments
Samsung ElectronicsService Manual
7.7 How to use EDC (Engine Diagnostic Control) Mode
7.7.1 EDC Establishment
EDC Mode is feature that allows the engineer to check the condition of the print engine. It can check the operating condi-tion of the motors, sensors, solenoids and clutches, measure the High Voltage from the HVPS and check the operation ofthe fuser and LSU.
7.7.1.1 How to enter the EDC Mode
a) Turn on the printer while pressing the "Enter" key. Hold the key until 'Select Test mode' appears in the display.
b) Press the direction key until "<EDC Test>" is displayed.
c) Press the "Enter" key.
d) <Enter Access Key> appears in the display. Press the cancel key twice.
Note. There are a number of other test modes. Only EDC Test and Panel Tests should be used by service engineers, allother functions are for factory use only.
7.7.1.1 Functions of the keys on the Panel and how to use them.
Key Function Description
On Line Not used
Cancel Not used
Menu Menu Display Top Menu of EDC Mode
Left/Right Arrow Find Menu Move Menu
Confirm Run/Select Run run the Function / Select Menu
Upper Menu Stop/Move Stop Stop the selected Function or go to Upper Menu.
7.7.1.2 LCD Function and Directions
Upper Line : Upper Line messages mainly show the current test menu or sub-menu. [Main Menu] or [Function] is displayed.
Lower Line : Lower Line messages mainly the current test and status.
Buttorns
Status Map Display : dispaly the printerstatus and job in progress.
7-19Samsung Electronics
Alignment & Adjustments
Service Manual
7.7.2 EDC Whole Menu
Motor Test
Main Motor
Dev Motor
Waste Motor
SCF Motor
Fan Motor
HVPS Test
Solenoid Test
Y Clutch
M Clutch
C Clutch
K Clutch
Y Solenoid
M Solenoid
C Solenoid
K Solenoid
Feed Clutch
T2 Solenoid
FCF Solenoid
MPF Solenoid
SCF Solenoid
ITB Solenoid
Duplex Solenoid
Feed Sensor
Exit Sensor
FCF Empty Sensor
MPF Empty Sensor
SCF Empty Sensor
SCF Cover Sensor
Waste Box Sensor
Cover Check
Sensor Test
LSU Motor
Laser Diode
Fuser
LSU & Fuser Test
Charger
T1
T2
Dev DC
Dev AC
Test Print
Select Tray
Select Pattern
Print Pattern
Print Menu Map
Interface Test
SCF Interface
7-20
Alignment & Adjustments
Samsung ElectronicsService Manual
7.7.2.1 Motor Test
This function allows the operation of the various motors to be checked.
<How to operate>a) Press the "<" or ">" key until "Motor Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the motor you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Item Description Remarks
Main Motor Operates Main Motor Displays "Succeed" if Motor Lock Signal is Normal, "Failed" otherwise.
Dev Motor Operates Dev Motor Displays "Succeed" if Motor Lock Signal is Normal, "Failed" otherwise.
Waste Motor Operates Waste Motor Display motor status - "On" or "Off".
SCF Motor Operates SCF Motor Display motor status - "On" or "Off".
Fan Motor Operates Fan Motor Display motor status - "On" or "Off".
7-21Samsung Electronics
Alignment & Adjustments
Service Manual
7.7.2.2 Solenoid Test
This function allows the operation of various solenoids and clutches to be checked.
<How to operate>a) Press the "<" or ">" key until "Solenoid Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the clutch or solenoid you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Item Description Remarks
Y Clutch Operates Yellow Developer Clutch Displays clutch status - "On" or "Off".
M Clutch Operates Magenta Developer Clutch Displays clutch status - "On" or "Off".
C Clutch Operates Developer Clutch Displays clutch status - "On" or "Off".
K Clutch Operates Black Developer Clutch Displays clutch status - "On" or "Off".
Y Solenoid Operates Yellow Developer Solenoid Displays solenoid status - "On" or "Off".
M Solenoid Operates Magenta Developer Solenoid Displays solenoid status - "On" or "Off".
C Solenoid Operates Cyan Developer Solenoid Displays solenoid status - "On" or "Off".
K Solenoid Operates Black Developer Solenoid Displays solenoid status - "On" or "Off".
Feed Clutch Operates Feed Clutch Displays clutch status - "On" or "Off".
T2 Solenoid Operates T2 Clutch Solenoid Displays solenoid status - "On" or "Off".
FCF Solenoid Operates FCF pick-up Displays solenoid status - "On" or "Off".
MPF Solenoid Operates MPF pick-up Displays solenoid status - "On" or "Off".
SCF Solenoid Operates SCF pick-up (Only if SCF is fitted) Displays solenoid status - "On" or "Off".
ITB Solenoid Operates ITB cleaning Solenoid Displays solenoid status - "On" or "Off".
Duplex Solenoid OperateS Duplex Solenoid Displays solenoid status - "On" or "Off".
7-22
Alignment & Adjustments
Samsung ElectronicsService Manual
7.7.2.3 Sensor Test
This function allows the operation of various sensors to be checked
<How to operate>a) Press the "<" or ">" key until "Sensor Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the sensor you wish to test.
d) Press the "Enter" key to display the sensor status. If the sensor actuator is moved the displayed status will change toreflect the new sensor position..
e) Pressing the "Upper Level" key will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Item Description LCD indication
Feed Feed Sensor Status "With Paper" is displayed when Paper is detected, "Without paper" is displayed when paper is not detected.
Exit Exit Sensor Status "With Paper" is displayed when Paper is detected, "Without paper" is displayed when paper is not detected.
FCF Empty FCF Empty Sensor status "With Paper" is displayed when Paper is detected, "Without paper" is displayed when paper is not detected.
MPF Empty MPF Empty Sensor Status "With Paper" is displayed when Paper is detected, "Without paper" is displayed when paper is not detected.
SCF Empty SCF Empty Sensor Status "With Paper" is displayed when Paper is detected, "Without paper" is displayed when paper is not detected.
SCF Cover SCF Cover Sensor Status "Cover Opened" or "Cover Closed" is displayed.
Waste Box Waste Toner Sensor Status "Not Installed" is displayed when either the Waste toner tank is not installed orit is full."Installed" is displayed when the Waste Toner tank is installed and is not full.
Cover Left or Right Cover Sensor Status "Cover Opened" or "Cover Closed" is displayed.
7-23Samsung Electronics
Alignment & Adjustments
Service Manual
7.7.2.4 LSU & Fuser Test
This function allows the Fuser, LSU Motor and Laser Diode to be tested.
<How to operate>a) Press the "<" or ">" key until "LSU & Fuser Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of part you wish to test.
d) Press the "Enter" key to run the test. The test is stopped by pressing the "Upper Level" key.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
• The LSU Motor Lock Time is a maximum 15 seconds depending on the environment. It may take over 15 seconds untilthe <Succeed> or <Failed> message is displayed.
• For safety - after printing a test pattern if you need to return to EDC mode turn the printer off and then re-enter EDC.
Item Description Remarks
LSU Motor Operates LSU Motor The LSU motor must come into lock within 6 seconds. After 7 secs thestatus is displayed either: "Succeed" if lock is successful within the time limit "Failed" if lock is not achieved
LD Operates Laser Diode
Fuser Heats the Fuser Repetitive cycle (10secs) - Lamp on for 500msec then off again.
7.7.2.5 Interface Test
This function tests communications between the Main PBA controller and the SCF controller.
<How to operate>a) Press the "<" or ">" key until "Interface Test" is displayed.
b) Press the "Enter" key to select and run this function.
c) "Succeed" or "Failed" is displayed..
d) Pressing the "Upper Level" key again will return to the EDC main menu.
7-24
Alignment & Adjustments
Samsung ElectronicsService Manual
7.7.2.6 Test Print
This function allows you to test the overall function of the print engine. You can select either a 4 * 4 color bar pattern or asolid color pattern. If the solid pattern is selected 4 pages are printed - one for each color. You can also print the EDCMode Menu Map.
<How to operate>a) Press the "<" or ">" key until "Test Print" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until "Select Tray" is displayed.
d) Press the "Enter" key to select this function.
e) Press the "<" or ">" key until required tray is displayed and then press the "Enter Key"
f) Press the "Upper Level" key.
g) Press the "<" or ">" key until "Select Pattern" is displayed.
h Press the "Enter" key to select this function.
i) Press the "<" or ">" key until required pattern is displayed and then press the "Enter Key"
j) Press the "Upper Level" key.
k) Press the "<" or ">" key until "Print Pattern" is displayed.
l) Press the "Enter" key to print the pattern.
For safety - after printing a test pattern if you need to return to EDC mode turn the printer off and then re-enter EDCMode by turning power on whilst holding in the "Enter" key.
7-25Samsung Electronics
Alignment & Adjustments
Service Manual
7.7.2.7 HVPS Test
This function allows the HVPS to be tested
<How to operate>a) Press the "<" or ">" key until "HVPS Test" is displayed.
b) Press the "Enter" key to select this function.
c) Press the "<" or ">" key until you see the name of the voltage you wish to test.
d) Press the "Enter" key to select the test.
e) Press the "<" or ">" key to select the appropriate Duty Cycle and press "Enter" to start the test
The test is stopped by pressing the "Upper Level" key.
The display shows the acceptable range for this setting (column 4 in the table below)
The mid range (nominal) voltage is shown in column 3 in the table below.
e) Pressing the "Upper Level" key when the test is already stopped will return to step 'c' above.
f) Pressing the "Upper Level" key again will return to the EDC main menu.
Item DescriptionLower Menu & Input
LCD IndicationVoltage
Charger Supply Voltage to the Charger Duty 50% : -1262V Duty 50% : -1224V ~ -1300VDuty 80% : -2037V Duty 80% : -1976V ~ -2098V
T1 Supply Voltage to T1 Duty 50% : 1174V Duty 50% : 1139V ~ 1209VDuty 90% : 2080V Duty 90% : 2018V ~ 2142V
T2 Supply Voltage to T2 Duty 30% : 1800V Duty 30% : 1746V ~ 1854VDuty 80% : 4540V Duty 80% : 4404V ~ 4676Reverse Bias : -900V Reverse Bias : -800V ~1200V
Dev DC Supply DC Voltage to Dev Duty 45% : -370V Duty 45% : -359V ~ -381V
Dev AC Supply AC Voltage to Dev Duty 35% : -2200V Duty 35% : -2134V ~ -2266V
* The allowed tolerance is commonly +/- 3%, this is the value Displayed, in case of "Dev AC", it is the value of Vpp.* T2 Reverse Bias.(Tolerance : +/-20%)
7-26
Alignment & Adjustments
Samsung ElectronicsService Manual
MEMO
88
8-1Samsung Electronics
Troubleshooting
Service Manual
8. Troubleshooting
8.1 Procedure of Checking the Symptoms
Before attempting to repair the printer first obtain a detailed description of the problem from the customer.
OP PanelON?
Refer to"8.1.1 Basic Check List"
Printingguality isnormal?
END
Readyor
Power Save
Indicate"Error Message"
Power On
- No Power- LCD Module- Main PBA
Refer to"8.5 Error Message"
Refer to "8.2 Solution of Image Problem"
8-2
Troubleshooting
Samsung Electronics
Service Manual
8.1.1 Basic Check List
1. Check the Power.
• Does "Warming Up" appear on the display?
--> If not check power cable, switch or SMPS. (see section 8.1.2 below)
--> Does the wall socket work?
• Do the Motors or other components initialize (listen for main motor, fan and LSU sounds)?
--> If not or there are none of the normal startup sounds check cable, switch or SMPS.
--> Does the wall socket work?
2. Check the LCD Panel.
• Is there any display at all?
--> If not check power cable, switch or SMPS. (see section 8.1.2 below)
--> Does the wall socket work?
• Is the display a meaningful message (are there any broken or badly formed characters)?
--> Check the main PBA and cable harness.
• Is the message on the LCD Panel a standard error message?
--> Refer to section 8.4 or 8.5 (Page 8-14 or 8-18).
3. Check the Paper Path
• Is there a Paper Jam?
--> Remove any paper fragments caught in the paper path.
--> Refer to section 8.3 (Page 8-10).
• Paper Jam occurs repeatedly at a specific point in the Paper Path
--> Dismantle the machine and carefully inspect the region where the jam occurs. (Especially, check if paper fragments are caught in the Fuser
4. Print the Information Page (Configuration).
• Is there a problem?
--> If there is an error see section 2) or 3) above.
• Try printing a test page from a computer.
--> If there is an error check cables and driver installation.
5. Check the Print Quality.
•Is there are a Print Quality Problem?
--> Refer to section 8.2 (Page 8-5).
6. Check consumables (toner etc.).
•Using the keys print the Information Page.
--> Refer to 8.1.4 below and to section 3.5 (Page 3-3) for expected life of various consumable parts, compare this withthe figures printed and replace as required
8-3Samsung Electronics
Troubleshooting
Service Manual
8.1.2 Initial Inspection
1. Check Power part
1. The printer does not work no matter how long you wait.
A. Is the Power Switch (printer and wall socket) turned on ?
B. Is the Power Cord connected to the printer correctly ?
C. Is the Power cord connected to the wall socket correctly ?
D. Is wall socket working ?
E. Is the unit rated at the same voltage as the supply ?
2. Does the Fan work when power is turned on?
A. Check the connectors on the SMPS.
B. Check the fuses in the SMPS.
C. Check any error message display on the LCD panel and refer to the troubleshooting section 8.4 or 8.5 (Page 8-14 or 8-18).
2. Check the Installation Environment.
1. Ensure the installation surface is flat, level and free from vibration.
If necessary move the printer.
2. Ensure that the temperature and humidity of the surroundings are within specification
If necessary move the printer.
3. Ensure that the printer is position away from any air conditioning or other heating or cooling equipment. Also ensurethat is not positioned in a direct draft from any air conditioning, fan or open window.
If necessary move the printer.
4. Ensure the printer is not positioned in direct sunlight.
If it is unavoidable use a curtain to shade the printer.
5. Ensure the printer is installed in a clean dust free environment.
Move the printer to clean area if necessary.
6. Some industrial or cleaning processes give of fumes which can affect the printer.
Move the printer away from this type of air pollution
3. Check paper type.
1. Use only paper which is of a suitable quality, weight and size?
See the user guide.
4. Check the overall condition of the printer
1. Is the printer properly maintained ?
Clean the Paper Transport Passages.
Any rollers with dirt surfaces should be cleaned or replaced.
8-4
Troubleshooting
Samsung Electronics
Service Manual
8.1.3 Check the length of life of components
The length of life of consumable components is displayed either by operating time (% of life) or quantity of output. Theprinter will not work if any of these parts have exceeded there expected life. When a user replaces any of these consumableparts they must reset the appropriate counter using the maintenance menus (see section 7.4, page 7-13).
The printer calculates the working time and quantity of output for each component and saves this information.
1. The Working time for each component (OPC Drum, Toner Cartridge, Image Transfer Belt, Fuser Unit) is measuredevery 30 seconds when the Transport Motor and Fusing Contact Motor are active.
2. In order to calculate the number of images printed 1 is added to the appropriate counter every 30 seconds. Theamount of waste toner is calculated based on the number of pixels in the image.
3. When the user replaces any of the consumable parts and resets the appropriate counter it starts again from 0.
8-5Samsung Electronics
Troubleshooting
Service Manual
8.2 Solution of Image Problem
Cause Sequence of Treatment
Driver Installation Problem.
Toner cartridge contacts dirty or not makinggood contact or empty Toner Cartridge(when printing a single color image)
ITB cartridge contacts dirty or not makinggood contact or Faulty ITB unit
LSU cable harness plugs not fitted properlyor faulty LSU.
Toner transfer problem
Try printing a Demo Page.Check that the operating system driver wasinstalled correctly.
Check and clean the toner contacts.Re-seat the Toner Cartridge.Replace the Toner cartridge
Check and clean the ITB contacts.Re-seat the ITB Unit.Replace ITB Unit
Check the connectors on the LSU Unit andmain PWA are properly inserted.Replace the LSU Unit, cables or MAIN PWAas required
Check all HV contacts and cables.Replace the HVPS.
- No Image
Cause Sequence of Treatment
OPC Drum BIAS contacts dirty or not mak-ing good contact.
Charge Voltage of the OPC Drum is unstable.
Clean Drum contacts..Replace the OPC Drum.
Replace the HVPS Board.
- Completely Black Image
Cause Sequence of Treatment
Contamination of the internal mechanism of thetoner cartridge
OPC Drum surface contaminated or damaged.
ITB Unit belt is contaminated or damaged.
Fuser Unit is contaminated.
Replace the Toner Cartridge.
Replace the OPC Drum.
Replace the ITB Unit Belt.
Clean or replace the Fuser Unit.
- White Spots / Black Spots / Colored Spots
8-6
Troubleshooting
Samsung Electronics
Service Manual
Cause Sequence of Treatment
Paper Path is contaminated.
ITB Unit Belt is contaminated.
Pressure Roller of Fuser Unit is contaminated.
Open covers fully and clean the Paper Path.
Clean or replace the ITB Unit.
Clean or replace the Fuser Unit.
- Toner Smudges on the reverse side.
Cause Sequence of Treatment
If the background is contaminated with onlyone color.
If the background is generally contaminatedwith all color.
If Printing Density is dark(one color only).
If Printing Density is dark(all colors).
Replace the appropriate Toner Cartridge
Ensure TDC process is enabled.If problem persists replace the OPC Drum
Replace the appropriate Toner Cartridge
Ensure TDC process is enabled.If problem persists replace the OPC Drum
- Foggy back ground
Cause Sequence of Treatment
Poor toner transfer to OPC-one color only
Poor toner transfer to OPC- al colors
Poor toner transfer to ITB Unit
ITB Bias voltage incorrect.
Check and clean Toner contactsReplace the appropriate Toner Cartridge
Check and clean Toner, ITB and OPC unitcontactsEnsure TDC process is enabled.If problem persists replace the OPC Drum
Check and clean ITB Unit contacts.Re-install or replace the ITB Unit.
Check and clean ITB Unit contact.Replace the HVPS.
- Low image density
8-7Samsung Electronics
Troubleshooting
Service Manual
Cause Sequence of Treatment
Developing process is contaminated.
ITB Unit is damaged or dirty
Fuser Unit is damaged or dirty
Lens Cover of LSU is damaged or dirty.
Replace the Toner Cartridge.Replace the OPC Drum.
Replace the ITB Unit.
Clean or Replace the Fuser Unit.
Clean the Lens Cover of LSU.Replace the LSU if the glass is damaged
- Black / White / Colored Lines and Bands
Cause Sequence of Treatment
Afterimage on the OPC
Afterimage on the ITB Unit.
Toner Cartridge is installed incorrectly.
Individual color layers offset.
Replace the OPC Drum.
Re-install or replace the ITB Unit.
Re-set the Toner Cartridge.
Replace ITB Unit.
- Offset Image
Cause Sequence of Treatment
Problem transferring intermediate images tothe ITB .
Contamination of the Paper Path.
Problem transferring intermediate image ontopaper
Check and clean ITB contactsRe-install or replace the ITB Unit.
Open the covers, check and clean the PaperPath.
Check and clean T2 roller contactsCheck T2 Solenoid and cam operation - ensureT2 comes properly into contact when solenoidoperates.
- Deterioration of Print Quality for all Colors.
8-8
Troubleshooting
Samsung Electronics
Service Manual
Cause Sequence of Treatment
If the of Toner Cartridge is bad
If the alignment betweem the OPC and ITBUnits is not carrect.
Uneven contact between OPC and ITB orbetween ITB and T2 roller.
Check or replace the Toner Cartridge.
Re-install the OPC and ITB Units.
Re-install or replace the ITB Unit.Check T2 roller, solenoid and cam operation.
- Deterioration of Printing Quality for Specific Color.
Cause Sequence of Treatment
Uneven contact between OPC and ITB orbetween ITB and T2 roller.
Uneven color may occur when a toner cartridge has just been installed.
Re-install or replace the ITB Unit.Check T2 roller, solenoid and cam operation.
Make test printing a couple of times.
- Uneven Color Density
Cause Sequence of Treatment
Moisture or wet paper.
Creases in paper.
Fault occurs in Duplex Printing only.
Ensure paper is stored properly and is not damp.Check paper storage conditions.
1) Creases : Replace the Guide Input.2) Replace the Fuser Unit.3) Check OPC, Drum, Toner Cartridge and ITB
Unit for contamination and replace as required.
Replace the Duplex Unit.
- Whited out area
8-9Samsung Electronics
Troubleshooting
Service Manual
Cause Sequence of Treatment
Contamination or damage to rollers.Measure distance between lines.
Laser Unit damaged
Damage or contemination of OPC drum
Refer to Table of Circumferences of Rollers.- Mark in same position on every page.
Replace ITB UnitReplace OPC Drum
- Mark every 75.36 mmReplace T2 roller
- Mark every 29.28 mmReplace Toner cartridge
Line repeats every 1~2 mm-Replace the LSU Unit.
Random line spacing-Replace the OPC Drum.
- Lateral Lines
Cause Sequence of Treatment
Contamination or damage to rollers.Measure distance between lines.
Laser Unit damaged
Damage or contemination of OPC drum
Refer to Table of Circumferences of Rollers.- Mark in same position on every page.
Replace ITB UnitReplace OPC Drum
- Mark every 75.36 mmReplace T2 roller
- Mark every 29.28 mmReplace Toner cartridge
Line repeats every 1~2 mm-Replace the LSU Unit.
Random line spacing-Replace the OPC Drum.
- Regularly repeating image defect
8-10
Troubleshooting
Samsung Electronics
Service Manual
Symptoms : Printing begins at wrong position on the paper.
Check and Cause Solution
Wrong sensor timing caused by defective feed sensoractuator.
Replace the defective actuator
8.3.2 JAM 0
Symptoms 1. Paper has not exited from the cassette.2. "Jam-0" occurs even though the paper feeds into the printer.
8.3.1 Top Margin Error.
8.3 Paper Feeding Problems and Troubleshooting
Pick-upRoller
Feed Sensor
Paper Empty Sensor
Check and Cause Solution
1. Check the Feed Solenoid or Pick-Up using EDS Mode.
2. Check that the Separator Pad hasnot become loose.
3. Check if the surface of the Pick-UpRoller is clean.
4. Check the Feed Sensor is notsticking by using the EDC Mode(When “JAM-0” occurs eventhough the paper feeds into theprinter.)
1. Replace the Solenoid.
2. Replace the Separator - Pad(inside the Cassette).
3. Clean the surface of the Pick-UpRoller with IPA or water.
4. Replace the main PBA or Sensor.
8-11Samsung Electronics
Troubleshooting
Service Manual
8.3.3 JAM1(JAM inside pinter)
Symptoms Paper is jammed in front of the Fuser or under the T2 Roller.
Exit Sensor
Feed Sensor
Check and Cause Solution
1. If the paper is jammed in front of orinside the Fuser
2. If the paper is caught in the ExitRoller and the Fuser check theFeed Sensor actuator opens andcloses freely.
1. Replace the SMPS.
2. - Re-assembly the Feed Actuatorand Spring, or clean the Hingewith a lint free cloth.
- Replace the Main PBA.
8.3.4 JAM 2 (Jam in Exit Area)
Symptoms1. Paper is jammed inside the Fuser.2. Paper is caught in the Exit Sensor Actuator.3. Paper is caught in the Exit Roller and Fuser, after passing through the Feed Sensor actuator
Exit SensorCheck and Cause Solution
1. The Exit Sensor is defective if Jam2 occurs after the paper is completely fed out of the printer.This can happen if the actuatorsticks open or is slow to close.
2. Paper is rolled into the Fuser.• “Accordion” folding occurs
repeatedly.• Fuser temperature is too high
due to failure or other abnormalconditions.
• If the Heat Roller or PressureRoller is conteminated hardbecause of Toner.
3. If there are “Accordion” paper foldsinside the Fuser.
4. If the Exit Sensor is defective. aJam In Exit Area will occur andprinting will stop.
1. Check if the Exit Sensor Actuator isbroken or damaged.• Check if the Exit Sensor Actuator
is deformed (Check that the senorarms are not deformed).
• Check for Burrs or rough edges inthe Exit Actuator assembly, andcheck that the sensor arms arefree to move.
• Check for foreign objectsobstructing the Exit actuator.
2. Replace the Fuser.
3. • Replace the Exit Guide.• Check that the Exit unit is assem-
bled properly and full functioningand replace if necessary.
4. Replace the Exit Sensor.
8-12
Troubleshooting
Samsung Electronics
Service Manual
8.3.5 JAM Duplex
Symptoms Indicated "Jam in Duplex Area" on the LCD indicator.
Exit Sensor
Feed Sensor
Check and Cause Solution
1. Paper in the duplex path fails tooperate the Feed Sensor.
2. Paper in the duplex path fails toreach the Feed Sensor because ofjamming in the Duplex Path.
1. Replace the Feed Sensor or ExitSensor.
2. Check that there are no foreignobjects or fragments of paper in theDuplex Path. If necessary replacethe Duplex Unit.
8.3.6 Multi-Feeding
Symptoms Multiple sheets of paper are picked up and fed simultaneously.
Check and Cause Solution
1. Check the On/Off operation of the pick-up Solenoidusing the EDC Mode.
2. Check the Friction Pad surface for dirt or other conta-mination.
3. Check that the paper is not creased, folded orcurved.
4. Check that the Paper Guide in the cassette is properlyadjusted and that paper is poperly loaded.
5. Influence of Static Electricity.
1. Replace the Solenoid, harness or Main PBA.
2. Clean the Pad-Friction using a lint free cloth andwater or IPA.
3. Use fresh paper.
4. Adjust the Paper Guide and load paper under theFinger.
5. Fan paper before loading to reduce the effects of staticelectricity.
8-13Samsung Electronics
Troubleshooting
Service Manual
8.3.7 Paper rolling in the Fuser.
Symptoms Paper is rolled in the Fuser.
Check and Cause Solution
1. If the Heat Roller is conteminated. (Background, Hot off set)
2. If “Accordion” folding occurs between the Fuser andthe Exit Unit repeatedly.
3. If the Bearing - Fuser or Gear - Fuser is damaged ormelted by excessive heat.
1. Replace the Fuser.
2. Check if the Paper Guide Ribs on the Exit Unit aredamaged or contaminated, and check the conditionand operation of the Exit Roller.
3. Check the SMPS and Main PBA if the Bearing Gearis melted.
8-14
Troubleshooting
Samsung Electronics
Service Manual
8.4.1 Fuser Error
8.4 Symptoms of Bad Operation and Troubleshooting.
Symptoms Open Fuser / Over Heat / Low Heat displayed on the LCD Panel.
Check and Cause Solution
1. Check the continuity of the Thermostat, AC Wire andHeat Lamp.
2. Check the continuity of the Thermistor and thermistorharness / contacts.
3. Test the Heat Lamps and the overheat circuitry.
4. Check the fuser for any evidence of damage due tooverheating or melting.
1. Replace the whole Fuser assembly if the Thermostatis open circuit, otherwise replace heat lamps asrequired..
2. Replace broken thermistor or cables as necessary.
3. Replace the main PBA id the overheat circuit is faulty..
4. Replace the Fuser.
8.4.2 LSU Error
Symptoms Engine LSU Error displayed on the LCD Panel.
Check and Cause Solution
1. Check the LSU Connector.
2. Check the LSU Motor.
3. Check the HSYNC signal.
4. Check the Deve Cover Micro switch.
1. Replace the LSU.
2. If the same error recurs replace the main PBA.
8.4.3 Fuser does not work due to the drive gear melting.
Symptoms The fuser gears melt and the roller drive fails.
Check and Cause Solution
1. The Fuser makes a noise and fails to operate, rollersmay not rotate.
- Replace the Fuser.- Replace the Main PBA.- Replace the SMPS.
8-15Samsung Electronics
Troubleshooting
Service Manual
8.4.4 Paper Empty
Symptoms LCD shows "Paper Empty" even though paper is ready.
Check and Cause Solution
1. Check for a broken or distorted paper empty sensoractuator. Check that the actuator is not jammed
2. Check the sensor connectors and cable harness.Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator.
1. Replace the Paper Empty Sensor actuator.
2. Replace the harness.
3. Replace the Sensor Board.
8.4.5 Paper Empty without indication.
Symptoms The machine remains 'Ready; even when the paper cassette is empty.
Check and Cause Solution
1. Check for a broken or distorted paper empty sensoractuator. Check that the actuator is not jammed.
2. Check the sensor connectors and cable harness.Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator.
1. Replace the Paper Empty Sensor actuator.
2. Replace the harness.
3. Replace the Sensor Board.
8.4.6 Cover Open
Symptoms LCD displays "Cover Open" error even though the cover is closed.
Check and Cause Solution
1. Check if the Hook Lever inside the Duplex Cover isbroken or distorted.
2. Check the Cover Open sensor, connectors and cableharness. Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator.
1. Replace the Duplex Cover.
2. Replace the harness or microswitch as necessary.
3. Replace the Sensor Board.
8-16
Troubleshooting
Samsung Electronics
Service Manual
8.4.7. Can not sense when the Cover is Opened.
Symptoms LCD Indicates "Ready" even when cover is opened.
Check and Cause Solution
1. Check if the Hook Lever inside the Duplex Cover isbroken or distorted.
2. Check the Cover Open sensor, connectors and cableharness. Ensure that a signal reaches the main PBA
3. Use the EDC mode to test the actuator.
1. Replace the Duplex Cover.
2. Replace the harness or microswitch as necessary.
3. Replace the Sensor Board.
8.4.8 Defective Motor
Symptoms Main Motor does not work and paper does not feed when printing. Jam 0 is displayed.
Check and Cause Solution
1. Check if the Motor Harness or Motor PCB is brokenor not.
2. Test the Motor using EDC Mode.
1. Replace the Motor or Motor Harness.
2. Replace the Main PBA.
8.4.9 No Power
Symptoms Power is not supplied to the set, or the LCD display is not on.
Check and Cause Solution
1. Check the power supply input and DC voltage outputfrom the SMPS. Check the fuses in the SMPS.Check the wall socket.
2. If the SMPS supply is OK, and the LCD still does notwork check the display connectors and cable harness
3. Check if +24VDC or other Power Supplies are shortedout.
1. Replace the Power Cable. Replace SMPS fuses. Ifthe fault recurs replace the SMPS.
2. Replace cables or LCD Panel Ass'y. Replace theMain PBA.
3. Replace the components used for +24VDC.
8-17Samsung Electronics
Troubleshooting
Service Manual
8.4.10 Curved or Distorted Vertical Lines
Symptoms Curved, wavy or distorted vertical lines.
Check and Cause Solution
1. Use EDC Mode to test the LSU. Check that the+24VCD signal between the main PBA and the LSUis stable
2. Check that the LSU clock is stable.
1. Replace the LSU or Main PBA.
2. Replace the Main PBA.
8.4.11 Low Toner
Symptoms "Ready Replace [Color]" is displayed on the LCD Panel.
Check and Cause Solution
1. "Low Toner" is displayed when under 500page orless toner remains (in any of the cartridges).
2. Check the condition of the contacts on the DEVEPBA.
1. Using the keypad check which toner is empty andreplace the Toner Cartridge.
- Replace the Toner Joint PBA.- Replace the Main PBA.
8.4.12 Replace Toner[CART].
Symptoms LCD displays "Ready Replace [CART]".
Check and Cause Solution
1. “Ready Replace CART” is displayed when the OPCImage Count value is over 50,000. Image Densitymay be reduced. It is possible to continue to print onePage at a time by pressing the “On-Line” button whenit flashes.
1. Replace the OPC Drum.
8-18
Troubleshooting
Samsung Electronics
Service Manual
ADC Not Confirm Error The ADC(Analog -to - Digital Conversion) is defective.
1. Turn the printer off, wait 30 secs and then turn it back on.2. Replace the Main PBA if the same symptoms recur.
Cover Open One of the covers is not properly closed
1. DEVE Cover or Duplex Cover is open. Check and close it correctly.2. Check the condition of the Cover Open Sensor assembly.
--> Replace if it is damaged or nor correctly fitted.
Dev. Motor ErrorThe developer motor may stop working because of a harness or con-nector fault, increased torque in any one of the toner cartridges due torollers sticking, a power supply fault or a fault on the main PBA.
1. Open the Deve Cover and check each Toner Cartridge to ensure that the rollers rotate.--> Turn the rollers by hand and check how difficult it is to rotate the rollers.--> Replace the toner cartridge if it seems excessively tight.
2. Open the Rear Cover and check if the Deve Motor Harness is assembled correctly.3. Open the Main PBA Cover and check if the Harness (20pins) connected to the Deve Drive PBA is assembled correctly.
--> Replace the Harness if there are damaged or badly fitted parts.4. Check the Power Supply to the Main PBA.
--> Replace the SMPS if the Power Supply is out of specification.--> Replace the Main PBA if the Power Supply from the SMPS is OK.
Engine Fuser Low Heat Error * The temperature of the Fuser is lower than the Printing temperature.* The Fuser harness is not connected properly.
1. Check that the Fuser is installed correctly.--> If not, re-install.
2. Check the AC power to the Fuser (Copper contact.)--> If it is no good go to step 3 below otherwise go to step 5.
3. Check the Thermostat on the Fuser.--> If it is open circuit replace the Thermostat.
4. Check that the Thermostat on the Fuser is properly positioned and assembled.--> Replace the Thermostat if it is not.
5. Check both of the fuser Heat Lamps.--> Replace any faulty lamps.
6. Check the Harness connected to the SMPS and Fuser.--> Refit the harness or replace if damaged.
7. Replace the Main PBA.8. Replace the SMPS.
8.5 Treatment of Error Message.
8-19Samsung Electronics
Troubleshooting
Service Manual
Engine FuserOver Heat Error The temperature of Fuser is higher than the Printing temperature.
1. Check both of the Thermostats on the Fuser.--> If it is open circuit replace the Thermostat.
2. Check that the Thermostat on the Fuser is properly positioned and assembled.--> Replace the Thermostat if it is not.
3. Check the Harness connected to the SMPS and Fuser.--> Refit the harness or replace if damaged.
4. Check the Fan and the Fan Harness--> Refit or replace as required
5. Replace the Main PBA.6. Replace the SMPS.
Warning : You must replace the complete Fuser Ass'y if Over Heat Error has occurred.Do not replace only the Thermistor.
Engine LSU Error There is a fault in the LSU unit.
1. Use EDC mode to test the HSYNC signal and LSU Motor.2. Check the Harness connected to the Engine Controller and LSU.
--> Refit the harness or replace it if it is damaged..3. Replace the LSU.
Main Motor Error The Main Motor that drives the OPC, ITB and Pick-Up is faulty.
1. Open the Deve Cover and Top Cover and then check the OPC Unit and ITB Unit.--> Re-install if they are not correctly fitted or are damaged.
2. Open the Rear Cover and then check the Main Motor Harness.--> Refit the harness or replace it if it is damaged.
3. Check if the Power Supply from the SMPS to the Main PBA.--> Replace the SMPS if the voltages are outside specification.
4) Check if the No. 7 of CN27 on the Main PBA is near 0V while Main Motor is powered on under the Mode EDC.--> Replace the Main PBA if the voltage is near 5V
5) Check if the Motor Clock is generated at the No. 9 of CN27 on the Main PBA while Main Motor is powered on underthe Mode EDC.--> Replace the Main PBA if isn't generated.
8-20
Troubleshooting
Samsung Electronics
Service Manual
Waste Motor Error This error is caused by open circuit of Waste Motor Harness or themotor stalling due to increased Waste Motor torque during operation.
1. Open the Front Cover and then check if the Waste Toner Tank is full or the waste inlets are blocked with the Waste Toner.--> Replace the Waste Toner Tank and unblock waste inlet feeds.
2. Open the Top Cover and then remove the ITB Unit and OPC Unit and check if the OPC waste toner outlet blocked.3. Remove the Front Cover and then check the Waste Motor Harness.
--> Refit or replace the harness if it is damaged.4. Remove the HVPS Cover and then check that the HVPS OEM Harness is correctly fitted.
--> Refit or replace the harness if it is damaged.5. Measure the Voltage on CN2 Pin1 and Pin3 of OEM PBA. (Normal : Over +10VDC)
--> replace the OEM PBA if there is no output.
Image Transfer Error This is caused by a badly fitted or unlocked ITB unit or a faulty ITBHome Sensor.
1. Open Top Cover and then check that the ITB unit properly fitted and locked in position.--> Remove, replace and re-lock the ITB unit.--> If the same fault recurs regularly replace the ITB unit.
2. Check the condition of the ITB Harness (especially if replacing the ITB does not resolve the problem).--> Refit or replace the harness if it is damaged.
3. Check the signal on Pin 1 of CN10 on the Main PBA.--> Replace the Main PBA if the signal is Active Low.
Invalid Drum Cartridge Can not communicate with the OPC Unit.
*This is caused by a wrong value of OEM Resistor in the OPC Unit.*It is also caused by miss-reading the value of the OEM Resistor because of contamination of the contact points.
1. Check that an original Samsung Drum Cartridge is fitted.--> If not replace the OPC drum.
2. Clean the OPC unit contact points.3. Check the Harness connected between the Main PBA and Toner OPC Unit.
--> Refit or replace the harness if it is damaged.4. Check the “R150” on the Engine Controller.
--> Replace the Engine Controller.
8-21Samsung Electronics
Troubleshooting
Service Manual
Invalid Image Transfer Can not communicate with ITB Unit.
*This may be caused by a wrong value of OEM Resistor in the OPC Unit.
1. Open the Top Cover and then check that it is correctly locked in position.--> Remove, replace and re-lock the ITB unit.
2. Replace the ITB Unit.3. If the fault continues after re-fitting the ITB unit several times check the voltage on Pin4 of CN10 on the Main PBA.
--> Replace the ITB Harness if the voltage is not correct.4. Replace the Main PBA.
Invalid Toner [Color] This is caused by a wrong value of OEM Resistor in the TonerCartridge.
1. Clean the 3 contact points on the Toner Cartridge and then re-install.2. Replace the Toner Cartridge if the same error recurs.3. Remove the Front Cover and then check the condition of the contacts between the OEM PBA and Terminal if the
same error occurs.--> Clean or Re-assemble.
4. Replace the OEM PBA, HVPS and Main PBA in order if the same error recurs.
Invalid NEW Toner [Color] This occurs when the Fusible Resistor in the Toner Cartridge does notbecome open circuit within regulation time.
1. Clean the 3 contact points on the Toner Cartridge and then re-install.2. Replace the Toner Cartridge if the same error recurs. 3. Replace the OEM PBA, HVPS and Main PBA in order if the same error recurs.
Jam 0 In [Tray] Paper is caught in the tray.
1. Open the Duplex Cover and then remove the paper stuck in the machine.2. Open the Cassette and after removing any trapped paper ensure that the cassette is properly loaded, not overfilled
and that paper guides are properly adjusted.3. Check that the location of Lever of the Feed Sensor is normal.4. Check that the operation of the Pick-Up Clutch under the Cassette is normal.5. If the Clutch does not work check the condition of the cable harness to the Main PBA.6. Replace the Main PBA if the voltage on Pin 2 of CN32, CN25 on the Main PBA is +24VDC.
(Normal Output : Pin 1 = +24VDC, Pin 2 = 0V)
8-22
Troubleshooting
Samsung Electronics
Service Manual8-22
Chapter 8. Troubleshooting
Samsung Electronics
Jam In Duplex Path Paper is caught while printing side 2.
1. Open the Duplex Cover and then remove the paper.2. Remove any foreign objects in the Duplex Path.
Jam In Exit Area Paper is caught in the Exit Area.
1. Check the Exit Sensor actuator.--> Replace the Fuser if the Exit Sensor actuator is damaged or bent.
2. Check that the Paper Guide Rib of the Output Guide is clean, and not damaged or distorted.--> Replace the Fuser or Exit Ass'y if it is not normal.
3. Check the condition and operation of the Fuser Rollers.
Jam Inside Printer Paper is caught inside printer
1. Open the Duplex Cover and then remove the paper.2. Check the Feed sensor actuator.
--> Replace the Feed Sensor if it is damaged or distorted.
Load Manual Press Cont Key
This is only displayed when printing in Manual Feed mode and theMPF tray is empty..
Load a sheet of print material and press the On-Line/Continue button. You need to press the button for each page tobe printed.
Load [Size] In [Tray] The size of paper in the tray and the size of paper required by the doc-ument being printed are different.
*In this case the size of paper and tray is indicated.
Load the correct size of paper.
8-23Samsung Electronics
Troubleshooting
Service Manual
Memory Overflow Not enough Memory Capacity.
The printer has insufficient memory to build the page image. The print process will be cancelled automatically and theprinter will return to the Wait Mode. Add more memory to the printer.
Page Too Complex The layout of document is to complex.
Try to print again after making the layout simpler and erasing any unnecessary images. If the message is appearrepeatedly you will need to add extra memory to the printer.
Press Cont Key Replace [Ctrl]
Not enough Toner
* Press the [On-Line/Continue] button to continue printing.* Replace the Toner Cartridge when the image quality becomes unacceptable.* You can select if this message will be displayed on the LCD Pane or not.
Press Cont Key Replace Drum
The OPC drum is coming to the end of its usable life and will needreplacing soon.
* Press the [On-Line/Continue] button to continue printing.* Replace the OPC Drum when the image quality becomes unacceptable.* You can select if this message will be displayed on the LCD Pane or not.
Press Cont Key Replace Transfer
The ITB Unit is coming to the end of its usable life and will need replacing soon.
* Press the [On-Line/Continue] button to continue printing.* Replace the ITB Unit when the image quality becomes unacceptable.* You can select if this message will be displayed on the LCD Pane or not.
8-24
Troubleshooting
Samsung Electronics
Service Manual
Press Cont Key Replace T2 Roller
The T2 roller is coming to the end of its usable life and will need replacing soon.
* Press the [On-Line/Continue] button to continue printing.* Replace the T2 roller when the image quality becomes unacceptable.* You can select if this message will be displayed on the LCD Pane or not.
Ready IP Conflict IP address conflict with the address of another device on the network.
This only occurs when the optional network interface is connected and configured for TCP/IP support. Change the IPAddress.
Ready [CMYK] Low Toner The indicated Toner Color cartridge is almost empty.
Replace the indicated Color Toner Cartridge.To temporarily improve printing for a short time remove the indicated toner cartridge and rock it gently from side to sidefor a short time before replacing it.
Replace Drum Cartridge This occurs when the OPC drum is not correctly installed.
1. Check that the OPC Unit is installed and locked correctly.2. Check the OPC OEM Harness to the Main PBA.
--> Refit or replace the harness if it is damaged.3. Replace the Main PBA.
Replace Image Transfer There is a problem with the ITB Unit installation.
* This occurs when the ITB Unit is not correctly installed and locked* This occurs when the value of the OEM Resistor in the ITB Unit is incorrectly detected due to contamination of the
contact.
1. Open the Top Cover and then check that the ITB Unit is installed and locked correctly.2. Clean the contacts on the ITB Unit3. Replace the ITB unit.
8-25Samsung Electronics
Troubleshooting
Service Manual
Replace Toner [Color] It occurs when the Toner Cartridge of indicated Color is not installed.
*If the Toner Cartridge does not be installed*The value of OEM Resistor be recognized by the value of opened due to the contamination of Contact point.
1. Open the Deve Cover and then check if the Toner Cartridge is installed.2. Check if the contact point is contaminated.3. Replace the Toner Cartridge.4. Replace the OEM PBA, HVPS and Main PBA in order.
Tray2 Error This occurs when Tray2 is not installed correctly.
Turn the printer off and re-install Tray2.
Tray2 Jam Cover Open The cover on Tray 2 is open.
Check and ensure that the cover of Tray2 is closed properly.
Waste Toner Full/Not Install Waste Toner Tank is full or not installed.
1. Check and replace the Waste Toner Tank or install it correctly.2. Check that the Waste Toner Sensor actuator lever is free and not damaged or distorted.3. Check the condition of the waste toner sensor cable harness and refit or replace if it is damaged.
8-26
Troubleshooting
Samsung Electronics
Service Manual
MEMO
99
Exploded drawings and service parts lists are given for items which may be expected to have a higher failure rate.
Where a failure occurs you can identify the part in the exploded diagram and, using the parts cross reference number, refer to the appropriate parts list to identify the part number.
Note : Parts numbers given here are correct at the time of publication. When ordering parts please use the on-line ordering system to check if there have been any changes to part numbers.
Part Number & Description format.
There are two types of Part number format.
Part numbers and descriptions are defined according to a company standard. The information below will help you to understand the part number format and assist when ordering spare parts.
This format is used throughout Samsung on all product ranges. Typically it is used for small components and electronic parts.
This format is controlled by individual Samsung Divisions and is used on specific products, typically for mechanical parts. Type 2 format part numbers fall into 2 categories:
Assemblies consisting of 2 or more parts. Also used for Service manuals, user guides and diagrams.
Ass’y parts and A/S privately used Parts can be distinguished by the part Code and Description. They are always Type 2 format. The 2 leading characters indicate private or assembly parts.
number letter
9. Exploded Views and Parts List (CLP-510/XBH)
BRKT Bracket: ex)IPR-BRKT SMPS
CS Compress: ex)SPRING-CS
ELA Electrical Assembly: ex)ELA UNIT-ITB
HOU Housing: ex)ELA HOU-COVER FRONT
IPR Iron Press: ex)IPR-BRKT SMPS
M Mold: ex)COVER-M-WASTE TONER UPPER
MEA Mechanical Assembly: ex)MEA UNIT-BRKT ECU UPPER
MEC Mechanic Combined unit: ex)MEC-BRUSH ANTISTATIC
PBA Printed circuit Board Assembly: ex)PBAMAIN-CONTROLLER
PMO Processing Mold: ex)PMO-COVER REAR
PPR Plastic Press: ex)PPR-SHEET/GUIDE PAPER
RPR Rubber Press: ex)RPR-RUBBER
Abbreviations for parts description
Content
9.1 Main Exploded View
9.2 Cover Front Exploded View
9.3 Cover Top Exploded View
9.4 Cover Deve Exploded View
9.5 Exit Ass’y Exploded View
9.6 Duplex Ass’y Exploded View
9.7 Deve-Drive Ass’y Exploded View
9.8 Main-Drive Ass’y Exploded View
9.9 Fuser Ass’y Exploded View
9.10 Cassette Ass’y Exploded View
9.11 SCF Cassette Ass’y Exploded View
9.12 Frame SCF Ass’y Exploded View
9.13 Main Frame Exploded View
9.14 Front Frame Exploded View
9.15 Rear Frame Exploded View
9.16 Base Frame Exploded View
9.17 MP Ass’y Exploded View
9.18 Pick-up Ass’y Exploded View
9.19 FeederAss’y Exploded View
9.20 Guide Paper Exploded View
9.21 ITB Cam Ass’y Exploded View
9.22 Dummy Fuser Base Ass’y Exploded View
9.1 Main Exploded View17
12
23 40
13-1
45
20
31
2
6 5 4
15
35
57
57-1
14
13
2622
3822
39
8
21
9
33
25
30
11
16-2
16-3
16-1 S
8
19-1
S9
19
41
3758
48
44
19-2
16
23 40
16-4
28
31
29
32
43-1
43-2
10
43
42
24
58
56-1
56-2
S8
56
56-3
7
52
49
49-3
49-3
49-1
49-5
49-2
49-4
18
51
9.2 Cover Front Exploded View
0
12 12-512-4
12-6
12-212-3
12-1
6
9
2
2
175
3
S5
S5S5
S4
S3
S3
S8
S3
7
711
11
10
4
S8
5
3
S8
9.3 Cover Top Exploded View
6
5
3
0
2
9
1
7S15
8
S15
4
9.4 Cover Deve Exploded View
4
0
2
6
12S14
S14
3
7
9
1
10
5
11 8
9.5 Exit Ass’y Exploded View
05
6
2
4
1
7
10
13
3
S8
S8
11-10
11-S8
11
11-8
11-9
11-21
11-1
11-4
11-S8
S8
11-1311-14
11-15
11-16
11-19
11-20
11-S8
11-20-1
11-20-2
11-18
11-12
11-11
11-17
11-2211-5
11-2
11-3
11-7
11-6
S14
9.6 Duplex Ass’y Exploded View
1-1-1
1-1-10
1-1-10 1-1-91-1-7
1-1-26
1-1-8
1-1-51-1-16
1-1-21
1-1-141-1-3
1-1-2
1-1-4
1-1-19
1-1-6
1-1-28
1-1-11
1-1-29
1-1-22
1-1-20
1-1
1-1-151-1-16
1-1-16
1-1-31
1-1-32
1-1-14
1-1-15
1-1-24 1-1-25
1-1-23
1-1-12
1-1-27
1-1-12-5
1-1-13 0
1
2
1-1-12-71-1-12-4
1-1-12-3
1-1-12-4
1-1-12-1
1-1-12-2
1-1-18
1-1-17
1-1-30
1-1-181-1-30
1-1-17S8
S5
S8
S8
S8
1-1-12-8
1-1-12-6
1-10
1-11
1-9
S8
S8
1-2
1-8
1-6
1-5
1-4
1-13
1-13-2
1-13-1
1-13-2
1-13-5
1-13-3
1-13-6
1-13-7
1-13-4
1-3
1-7
1-12
1-12
9.7 Deve-Drive Ass’y Exploded View
0
6
7 8
12
13
1716
1514
1110
54
31
918
1920
2
9.8 Main-Drive Ass’y Exploded View
0
3833
22
33
1930
27
36
39
12
24
23 37
325
16
326
S11
72
35
S11
1S
1729
34
412
18
1315
1712
1121
2628
5
8
3520
14
10
37
931
0
19
18
1732
8
621
1 3
4
57
20
S2
S2S2
S2
S2
S2
S212
1514
282524
2252
2328
29
3110
11
1213
S3
S3
S2
S331
2733
S2
S2
16
26
30
9.9 Fuser Ass’y Exploded View
8
0
3
159
7
4
1
2
12
S8
14
5
11
13
10
6
9.10. Cassette Ass’y Exploded View
14
15
9
15
0
323
7
11
4
10
6
1212
S8
S8
16
5
22
13
8
2021
17
19
9.11. SCF Cassette Ass’y Exploded View
11
0
S8
S5
15
S8 S8
S8
S8
S8
S5
S5
9
12
S5
4
6
10
7
5
2
9
19
17
16
8
14
2-1
2-5
2-6
2-7
2-32-4
2-22-S9
1
3
3-83-19
3-153-9
3-4
3-13-2
3-13
3-13
3-13
3-163-103-11
3-43-5
3-6
3-7
3-173-123-20
3-33-14
3-18
3-133-4
S8
S8
S8 S8
1-6
1-2
1-41-2
1-1
1-7
1-5
1-S91-8
1-9
1-3
9.12. Frame SCF Ass’y Exploded View
3
8
29
23
7
6
3-33-6
3-7
3-2
3-1
11
10
24
9
31
3-53-4
55-2
5-1
5-5
5-3
1
1-18
1-3
1-17
1-10 1-21
1-14
1-15
1-20
1-11
1-4
1-81-3
1-5
1-13
1-19
1-16
1-12
1-7
1-6
1-91-2
1-1-2
1-1-3
S11-1-4
1-1-1
1-1
1-1-5
13
17-317-7
17-8
17-9
17-4
17-117-2
17-5
17
16
17-6
20
32
30
36S5
2614
1827
25
12
2
9.13 Main Frame Exploded View
11
14
6
37
33
4
31
1012
25
26
8
4
30
36
3
22
17
1
18
21
13
19
7
9 27
3739
24
2
2-1
2-2
3-3
3-23-4 3-6
3-7
3-53-1
2-3
1-1
1-2
1-4
1-3
16
29
28
23
34
15
9.14 Front Frame Exploded View
36A
S8
S8
S8
1
28
25 10
334
23
2412
121
15
31
37
18
9
S8
S8
11
32
20
26
29
S5
S8
S8
35 22
S5
6
36A
2
19
4
34
36*
12
1
S9
30
5
38
33
14
16
7
131
S8
S8
17
8
(36A
+36
B)
36B
38
1
9.15 Rear Frame Exploded View
16
15
14
23
136
12
8
3
74
5
19
10
9
20
18
22
17
1
2
2425 S14
S1426
1121
S14
S14
S14
S14S14
S14
S14
S8
S8S8
S7
S8
9.16 Base Frame Exploded View
1519
20
0
134
24
17
17
1825
1
18
11
37
23
1
S5
6
2S9
9
14
22
10
21
85
16
12
9.17 MP Ass’y Exploded View
7
1
5
12
112
0
8
3
6
4
109
9.18 Pick-up Ass’y Exploded View
3
13
1
0
5
S8
5
67
8
8
9
10
12
11
1-1
22
S8
S8
23
1-2
14
3-1
25
811
15
13
4
3
2
2-1
8
8
19
21
16
17
18
115
5
5
20
1-3
2-3
24
2-2
3-53-43-2
3-3
9.19 Feeder Ass’y Exploded View
4
0
6
S9
3
5
5
7
1
2
9.20 Guide Paper T2 Ass’y Exploded View
S18
9
0
8
S876
5
10
12
3
1213
S811
4
9.21 ITB Cam Ass’y Exploded View
2S8
1
0
3
S5
4
9.22 Dummy Fuser Base Ass’y Exploded View
Parts List
Parts List(Model code : CLP-510/XBH)
Draw# Part Code Description Location SNA
9.1-1 JC96-03189A ELA UNIT-ITB_SET;CLP-510,SEC,XAA,ITB,SET SNA9.1-2 JC96-03190A ELA UNIT-OPC_SET;CLP-510,SEC,XAA,OPC,SET SNA9.1-3 JC96-03191B ELA UNIT-DEVE BK_2K;CLP-510,SEC,SEE,DEV SNA9.1-4 JC96-03194B ELA UNIT-DEVE C_1.5K;CLP-510,SEC,SEE,DEV SNA9.1-5 JC96-03193B ELA UNIT-DEVE M_1.5K;CLP-510,SEC,SEE,DEV SNA9.1-6 JC96-03192B ELA UNIT-DEVE Y_1.5K;CLP-510,SEC,SEE,DEV SNA9.1-7 JC72-01214A PMO-COVER DEVE INNER;CLP-500,HIPS,IVORY, T2152 SA9.1-8 JC96-03237A ELA UNIT-DE_DRIVE;CLP-510,SEC,EXPORT,-,- T2073 SA9.1-9 JC66-00563A ARM-COVER DEVE HINGE;CLP-500,SECC,T1.2,- H3000 SNA9.1-10 JC92-01630C PBA MAIN-CONT_BB_PLUS;CLP-510,SEC,KOREA, M0203 SA9.1-11 JC97-02037A MEA MAIN-FRAME;CLP-510,SEC,EXPORT,-,-,-, F1941 SA9.1-12 JC97-02039A MEA-EXIT;CLP-510,SEC,EXPORT,-,-,-,- E3212 SA9.1-12-4 JC72-01199B PMO-OPE KEY 2;CLP-510,ABS,36024,-,-,HB,- SNA9.1-13 JC97-01756A MEA-DUPLEX;CLP-500,SEC,EXPORT,-,-,-,- D3027 SA9.1-13-1 JC97-01761A MEA UNIT-T2;CLP-500,SEC,EXPORT,-,-,-,- K3629 SA9.1-14 JC97-01753A MEA-CASSETTE;CLP-500,SEC,EXPORT,-,-,-,- K3657 SA9.1-15 JC96-03235A ELA HOU-COVER FRONT;CLP-510,SEC,EXPORT,- H0010 SA9.1-16 JC97-01764E MEA HOU-COVER REAR;CLP-510,SEC,EXPORT,PA C3112 SA9.1-16-1 JC72-01201A PMO-COVER REAR;CLP-500,HIPS,IVORY,-,HR-1 Z2673 SA9.1-16-2 JC72-01202E PMO-_M_COVER REAR DECO;CLP-510,HIPS,D.GR SNA9.1-16-3 JC72-01203A PMO-COVER OPEN BOARD;CLP-500,HIPS,IVORY, Z2658 SNA6-1-16-4 JC68-01176A LABEL(P)-REAR;CLP-500,-,YUPO PAPER,100G, L0000 SNA9.1-17 JC97-01765A MEA HOU-COVER TOP;CLP-500,SEC,EXPORT,-,- Z2375 SA9.1-18 JC97-01766A MEA HOU-COVER DEVE;CLP-500,SEC,EXPORT,-, T2119 SA9.1-19 JC44-00077A SMPS-V2;CLP-510,-,AC/DC,50W,210-230VAC,- S7035 SA9.1-19-1 JC70-00415A IPR-BRKT SMPS;CLP-500,SECC,-,T1.0,-,-,-, S7030 SA9.1-19-2 JC63-00236A SHEET-SMPS;CLP-500,PVC,T=0.5,W174.0,L259 S0002 SA9.1-20 JC44-00075A HVPS-BB_PLUS;-,24V,21.6V~26.4V,-,MAX 5KV S7027 SA9.1-21 JC59-00020C UNIT-LSU BIGBANG PLUS;CLP-510,-,-,600DPI L7045 SA9.1-22 6031-001255 WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5, SA9.1-23 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.1-24 JC70-00382A IPR-BRKT GUIDE ECU C;CLP-500,SECC,-,T1.0 B0002 SNA9.1-25 JB39-00103A CBF HARNESS-LIU GND;SCX-1110F,WIRE,UL100 L5004 SA9.1-26 JB70-00168A ICT-PIN ADF;SCX-1110F,STS303,D2.0,-,-,-, A2006 SA9.1-28 JC39-00271A CBF HARNESS-MAIN LSU;CLP-500,WIRE HARNES L7005 SA9.1-29 JC39-00399A CBF HARNESS-PANEL;CLP-600,WIRE HARENSS,U SNA9.1-30 JC39-00389A CBF HARNESS-DEVE_MT;CLP-510,WIRE HARNESS SA9.1-31 JC39-00293A CBF HARNESS-MAIN_MOTOR;CLP-500,WIRE HARN M2052 SA9.1-32 JC39-00296A CBF HARNESS-MAIN_SMPS;CLP-500,WIRE HARNE H1149 SA9.1-33 JC47-00007A MEP-CLUTCH CAM SOLENOID;-,CLP-500,3.1W,D C9046 SA9.1-34 JC61-00984A BUSH-M-D8 L5;CLP-510,POM,ID8.0,OD12.0,L5 B0010 SA9.1-35 JC63-00548A SHEET-WINDOW LCD;CLP-510,PC,T0.5,-,-,-,- S7031 SA9.1-36 JC63-00234A SHEET-HVPS;MLC-500,PC,T=0.5,W136,L250,-, S0005 SNA9.1-37 JC63-00549A COVER-M-SMPS;CLP-510,ABS,-,-,-,-,-,BLK,5 S7034 SA9.1-38 JC66-00478A GEAR-OPC DRIVE 2_Z40;CLP-500,POM,DE20028 D4045 SA9.1-39 JC66-00512A CAM-T2 ENGAGE;CLP-500,POM,-,-,BLACK,L5.0 C0011 SNA9.1-40 JC66-00616A SHAFT-COVER EXIT HINGE;CLP-500,SUM24L,L7 H3068 SA9.1-41 JC70-00382A IPR-BRKT GUIDE ECU C;CLP-500,SECC,-,T1.0 B0002 SNA9.1-42 JC61-00978A BRACKET--P-ECU LOWER;CLP-510,SECC,T1.0,- SNA9.1-43 JC97-01760A MEA UNIT-BRKT ECU UPPER;CLP-500,SEC,EXPO K3532 SA9.1-43-1 JC70-00410A IPR-BRKT ECU UPPER;CLP-500,SECC,-,T0.5,- B0005 SNA9.1-43-2 JC70-00411A IPR-BRKT ECU OPTION;CLP-500,SECC,-,T0.5, B0006 SNA
SA : Service Available, SNA : Service not Available
9.1 Main
1
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.1-45 JC72-01147A PMO-COVER SENSOR BASE;CLP-500,HIPS,BLACK C0013 SNA9.1-48 6502-001093 CABLE CLAMP;DAWS-3NE,ID11*L34.8,-,NYLON6 C0014 SNA9.1-49 JC97-01838A MEA UNIT-LSU CLEANER;CLP-500,SEC,EXPORT, L7026 SA9.1-49-1 JC64-00093A SHUTTER-LSU CLEANER;CLP-500,PC/ABS,T2.5, C0016 SNA9.1-49-2 JC66-00673A SHAFT-CLEANER;CLP-500,SUM 24L,L229.9,D3. S0007 SNA9.1-49-3 6044-000121 RING-E;ID2,OD5,T0.4,PASS,STSC R0001 SA9.1-49-4 JC61-00843A PLATE-LINK REAR;CLP-500,SECC,T1.2,-,-,-, R0002 SNA9.1-49-5 JC61-00844A PLATE-LINK FRONT;CLP-500,SECC,T1.2,-,-,- F0003 SNA9.1-56 JC97-01949A MEA UNIT-DUCT FUSER;CLP-500,SEC,EXPORT,- D0010 SA9.1-56-1 JC72-01150A PMO-DUCT FUSER LOWER;CLP-500,PP,BLACK,-, D0008 SNA9.1-56-2 JC72-01151A PMO-DUCT FUSER UPPER;CLP-500,PP,BLACK,-, D0009 SNA9.1-56-3 JC31-00025A FAN-DC;AD0624MSA70GL(R1)DOL,CLP-500,PBT+ F5016 SA9.1-57-1 JC63-00271A COVER-M-WASTE TONER UPPER;CLP-500,ABS,-, T2020 SA9.1-57-2 JC63-00272A COVER-M-WASTE TONER LOWER;CLP-500,ABS,-, T2019 SA9.1-57-3 JC67-00044A CAP-TONER OPC;CLP-500,LDPE,-,-,-,GREEN,M SNA9.1-51 JC72-01176A PMO-DEVE OPEN LINK GUIDE;CLP-500,HIPS,BL O0002 SNA9.1-52 JC63-00308A COVER-M-LSU;CLP-500,HIPS,T2.0,-,-,HB,-,B C0017 SA
9.2-0 JC96-03235A ELA HOU-COVER FRONT;CLP-510,SEC,EXPORT,- H0010 SA9.2-2 JC63-00180A COVER-FRONT HINGE R;CLP-500,POM,-,-,-,-, H3010 SA9.2-3 JC64-00080A LOCKER-M-WASTER TANK;CLP-500,PC/ABS,ICE L6012 SA9.2-5 JB64-00007A LOCKER-LATCH PUSH;MJC-3305/CPQ,POM,BLK,- L2004 SA9.2-6 JC64-00087A LOCKER-TANK PIN;CLP-500,SUS304-WPB,-,-,- L6017 SA9.2-7 JC72-00766A PMO-TIE STOPPER;SCX-5100,-,NYLON66,NTR,- K4094 SA9.2-9 JC63-00546A COVER-M-FRONT INNER;CLP-510,HIPS,-,-,-,H Z2580 SA9.2-10 JC72-01194A PMO-COVER FRONT OPEN;CLP-500G,ABS,L-GRAY SNA9.2-11 JC72-01195A PMO-COVER FRONT PUSH;CLP-500,POM,WHITE,- P8003 SA9.2-12-1 JC63-00547A COVER-M_OPE PANEL;CLP-510,HIPS,-,-,-,HB, L6018 SA9.2-12-2 JC72-01197B PMO-OPE KEY 1;CLP-510,ABS,G71312,-,-,HB, SNA9.2-12-5 JC72-01200A PMO-OPE KEY 2 CAP;CLP-500,PMMA,MILKY WHI K0248 SNA9.2-12-6 JC92-01633A PBA MAIN-CONT_BB_PLUS;CLP-510,SEC,KOREA, M0406 SA
9.3-0 JC97-01765A MEA HOU-COVER TOP;CLP-500,SEC,EXPORT,-,- Z2375 SA9.3-1 JC72-01204A PMO-COVER TOP;CLP-500,HIPS,IVORY,-,VE-18 Z2712 SA9.3-2 6107-001220 SPRING-CS;SUS304WPB,HEAT TREATMEN,PI0.9, SNA9.3-3 JC72-01205A PMO-COVER TOP BUTTON;CLP-500,HIPS,IVORY, Z2713 SNA9.3-5 JC72-01206A PMO-COVER TOP OPENER;CLP-500,POM,WHITE,- Z2717 SNA9.3-6 JC72-01207A PMO-COVER TOP STACKER;CLP-500,HIPS,IVORY Z5039 SA
9.4-0 JC97-01766A MEA HOU-COVER DEVE;CLP-500,SEC,EXPORT,-, T2119 SA9.4-1 6107-001207 SPRING-TS;SWP,LEFT,PI1.4,D9.2,L6.5,-,-,I SNA9.4-1 6107-001203 SPRING-ES;SUS304-WPB,-,PI0.5,D4.5,L17.2, S0088 SNA9.4-2 JC70-00436A IPR-COVER DEV LOCK BAR;CLP-500,SECC,-,T1 Z2325 SNA9.4-3 JC68-01180A LABEL(P)-DEVE COVER;CLP-500,-,YUPO PAPER L0006 SNA9.4-4 JC72-01081A PMO-COVER DUP LOCKER F;CLP-500,POM,WHITE L6026 SNA9.4-5 JC72-01082A PMO-COVER DUP LOCKER R;CLP-500,POM,WHITE L6027 SNA9.4-6 JC72-01213A PMO-COVER DEVE;CLP-500,HIPS,IVORY,-,HR-1 T2151 SA9.4-8 JC72-01215A PMO-COVER DEV SPRING CAP;CLP-500,POM,WHI Z4126 SA9.4-11 6107-001198 SPRING-CS;SUS304-WPB,-,PI1,D11,L24,-,-,I S0008 SNA
9.5-0 JC97-02039A MEA-EXIT;CLP-510,SEC,EXPORT,-,-,-,- E3212 SA9.5-1 JC72-01099A PMO-COVER EXIT;CLP-500,HIPS,LIGHT GRAY,- Z2567 SA
9.2 Cover Front
9.3 Cover Top
9.4 Cover Deve
9.5 Exit Ass'y
2
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.5-2 JC72-01217A PMO-C/EXIT LOCK COVER;CLP-500,HIPS,LIGHT Z2507 SA9.5-3 JC70-00440A IPR-COVER EXIT BAR;CLP-500,SECC,-,T1.2,- Z2328 SNA9.5-4 JC72-01081A PMO-COVER DUP LOCKER F;CLP-500,POM,WHITE L6026 SNA9.5-5 JC72-01082A PMO-COVER DUP LOCKER R;CLP-500,POM,WHITE L6027 SNA9.5-6 6107-001223 SPRING-TS;SUS304 WPB,-,PI1.2,D9.9,L29,-, SA9.5-7 JC72-01098A PMO-COVER EXIT GUIDE;CLP-500,HIPS,LIGHT G2158 SNA9.5-10 JC70-00372A IPR-COVER EXIT HINGE;CLP-500,SECC,-,T1.2 H3030 SNA9.5-11 JC97-02040A MEA UNIT-EXIT FRAME;CLP-510,SEC,EXPORT,- SNA9.5-11-1 JC72-01103A PMO-GUIDE EXIT UPPER;CLP-500,PC/ABS,IVOR E4117 SNA9.5-11-2 JC66-00607B ROLLER-EXIT DRIVE;CLP-510,EPDM+SUM24L,¥Õ E3213 SA9.5-11-3 JC72-01345A PMO-BUSHING DP;CLP-500,POM,WHT,ID5MM, OD SNA9.5-11-4 JC70-00374A IPR-GROUND EXIT;CLP-500,SUS304-3/4H,-,T0 E4052 SNA9.5-11-5 JC72-40978A PMO-BEARING LARGE DP;ML-165,POM,BLACK,-, B1041 SA9.5-11-6 JC66-40912A GEAR-DUPLEX;ML-165,POM,M1.0,Z16,-,WHITE, D3021 SA9.5-11-7 6044-000159 RING-C;ID3,OD7,T0.6,PASS,STSC R0006 SA9.5-11-8 JC66-40911A GEAR-DP,IDLE;ML-165,POM,M1.0,Z21,-,WHITE G0198 SA9.5-11-9 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.5-11-10 JC67-00065A BRUSH-ANTISTATIC;CLP-500,SWT-805A+SUS 30 B0011 SNA9.5-11-11 JC72-01233A PMO-HOLDER GROUND BALL;CLP-500,PC,BLACK, K3987 SA9.5-11-12 JC72-01102A PMO-GUIDE EXIT LOWER;CLP-500,PC/ABS,IVOR E4110 SNA9.5-11-13 JC72-41007A PMO-ROLLER FD F;ML-165,POM,BLACK,-,-,-,- K4063 SA9.5-11-14 JC72-41008A PMO-ROLLER FD R;ML-165,POM,BLACK,-,-,-,- K4064 SA9.5-11-15 JC61-00547A HOLDER-EXIT(MC);SCX-5312F,PC,-,-,-,WHITE H0013 SNA9.5-11-16 JC61-00484A SPRING ETC-EXIT LOWER IDLE;SCX-5100,SUS3 Z4180 SA9.5-11-17 JC66-00608A ROLLER-EXIT IDLE;CLP-500,TEFLON,PI10.5,L R0010 SNA9.5-11-18 JC72-20901A PEX-ROLLER EXIT F_UP;ML-5000A,TEFLON,WHI E4091 SA9.5-11-19 JC70-00375A IPR-GROUND EXIT PLATE;CLP-500,SUS304-3/4 P5050 SNA9.5-11-20 JC97-01410A MEA UNIT-TERMINAL:L;ML-5000A,SAMSUNG,KOR K3637 SA9.5-11-20-1 JC61-70930A SPRING ETC-HV SMALL;ML-5000A,-,D4.5,-,L4 Z4198 SA9.5-11-20-2 JC70-40912A ICT-SHAFT HV LARGE;ML-5000A,SWCH18A,-,¥÷ S4027 SA9.5-11-22 JC61-00974A BRACKET-P-EXIT UPPER;CLP-510,SECC,T0.5,- SNA9.5-13 JC61-00850A GUIDE-EXIT REAR;CLP-500,PC,T2.0,-,-,BLAC G0007 SNA
9.6-0 JC97-01756A MEA-DUPLEX;CLP-500,SEC,EXPORT,-,-,-,- D3027 SA9.6-1 JC97-01758A MEA HOU-COVER RIGHT;CLP-500,SEC,EXPORT,- Z2374 SA9.6-1-1-1 JC70-00361A IPR-BRKT GUIDE A;CLP-500,SECC,-,T0.5,-,- G2101 SNA9.6-1-1-2 JC61-00841A HOLDER-M-SAW;CLP-500,PC(NH-1023),-,-,-,B H4034 SA9.6-1-1-3 JC70-10232A IPR-PLATE SAW;ML-80,SUS304 CSP 1/2H,-,T0 K3377 SA9.6-1-1-4 JC72-01084A PMO-FRAME DUPLEX;CLP-500,ABS,BLACK,-,HB, D3033 SNA9.6-1-1-5 JC72-01094A PMO-PULLEY BELT;CLP-500,POM,WHITE,-,M90- P7022 SNA9.6-1-1-6 JC66-20901A BELT-TIMMING;B32S2M280,CR+FG+NYLON,-,W3. B2018 SA9.6-1-1-7 JC66-00513A GEAR-DUPLEX IDLER_Z25;CLP-500,POM,M0.8,Z D3020 SA9.6-1-1-8 JC72-01077A PMO-COVER BELT;CLP-500,HIPS,BLACK,-,HB,- Z2540 SNA9.6-1-1-9 JC70-00367A IPR-BRKT GROUND TR;CLP-500,C5210P,-,T0.3 K4291 SNA9.6-1-1-10 6107-001202 SPRING-CS;SUS304,-,PI0.8,D6.9,L20,-,-,ID S0090 SNA9.6-1-1-11 JC66-00346A GEAR-MP/DUP DRV;SCX-5100,POM,SW-01,M0.8, G0340 SA9.6-1-1-12 JC97-01761A MEA UNIT-T2;CLP-500,SEC,EXPORT,-,-,-,- K3629 SA9.6-1-1-12-1 6044-000231 RING-E;ID5.0,OD11.0,T0.6,PASS,STS304 SA9.6-1-1-12-2 JC66-00515A GEAR-TRANSFER IDLER_Z47;CLP-500,POM,M0.8 G0447 SA9.6-1-1-12-3 JC66-00619A SHAFT-GUIDE TR;CLP-500,SUM22,L276,¥Õ6.0,S S0019 NA9.6-1-1-12-4 JC72-01087A PMO-HOLDER TRANSFER;CLP-500,POM,BLACK,-, K4004 SNA9.6-1-1-12-5 JC72-01090A PMO-LEVER TR FRONT;CLP-500,PC+GF20%,BLAC L4079 SNA9.6-1-1-12-6 JC72-01091A PMO-LEVER TR REAR;CLP-500,PC+GF20%,BLACK L4080 SNA9.6-1-1-12-7 JC72-01092A PMO-LINK TR FRONT;CLP-500,PC+GF20%,BLACK K4041 SNA9.6-1-1-12-8 JC72-01093A PMO-LINK TR REAR;CLP-500,PC+GF20%,BLACK, K4042 SNA
9.6 Duplex Ass'y
3
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.6-1-1-13 JC70-00368A IPR-BRKT GROUND TR1;CLP-500,SUS304,-,T0. K3276 SNA9.6-1-1-14 JC72-00764A PMO-SHAFT DUP DRIVER;SCX-5100,POM,BLACK, S4079 SA9.6-1-1-15 JC73-10203A RPR-RUBBER EXIT;ML-80,EDPM RUBBER,-,-,-, E4164 SA9.6-1-1-16 JG72-40744A PMO-BUSHING TX(B4);CF5700,POM,NTR+WHT(DE SA9.6-1-1-17 JC72-40361A PMO-ROLLER_EXIT;SCF(XR),POM,NATURAL,-,M9 R0015 SNA9.6-1-1-18 JC61-70976A SPRING ETC-FUSER EXIT;ML-7000,SUS304-WPB S0021 SNA9.6-1-1-19 JC70-00362A IPR-BRKT GUIDE B;CLP-500,SUS304,-,T0.3,- G2102 SNA9.6-1-2 JC72-01078A PMO-COVER DUPLEX;CLP-500,HIPS,LIGHT GRAY D3031 SNA9.6-1-3 JC70-00370A IPR-COVER DUP LOCK SHAFT;CLP-500,SECC,-, S4050 SNA9.6-1-4 JC72-01079A PMO-COVER DUPLEX HANDLE;CLP-500,HIPS,LIG D3029 SNA9.6-1-6 JC72-01081A PMO-COVER DUP LOCKER F;CLP-500,POM,WHITE L6026 SNA9.6-1-7 JC72-01082A PMO-COVER DUP LOCKER R;CLP-500,POM,WHITE L6027 SNA9.6-1-8 JC72-01080A PMO-COVER DUPLEX LINK;CLP-500,POM,WHITE, D3030 SNA9.6-1-9 JC63-00172A COVER-DUPLEX LINK R;CLP-500,POM,-,-,-,-, D3014 SNA9.6-1-10 JC72-01083A PMO-COVER DUPLEX RAIL;CLP-500,PC/ABS,BLA D3032 SNA9.6-1-11 JC63-00173A COVER-DUPLEX RAIL R;CLP-500,PC/ABS,-,-,- D3015 SNA9.6-1-12 6107-001194 SPRING-CS;SWP-B,BLK,PI0.9,D6.95,L20,-,-, S0032 SNA9.6-1-13 JC97-01759A MEA UNIT-TRAY MP;CLP-500,SEC,EXPORT,-,-, T4071 SA9.6-1-13-1 JC72-01096A PMO-TRAY CASE MP;CLP-500,HIPS,LIGHT GRAY T4107 SNA9.9.1-13-2 JC72-00857B PMO-TRAY LINK MP;CLP-500,PC/ABS,LIGHT GR T4121 SA9.6-1-13-3 JB70-10906A IPR-GUIDE LATCH;AMUNDSEN,STS C304-CSP-3/ G2113 SA9.6-1-13-4 JC72-00777B PMO-TRAY COVER MP;CLP-500,HIPS,LIGHT GRA T4108 SA9.6-1-13-5 JC72-00547H PMO-SIDE GUIDE MP;CLP-500,ABS,LIGHT GRAY G2300 SA9.6-1-13-6 JC72-00778B PMO-TRAY EXIT MP;CLP-500,HIPS,LIGHT GRAY T4113 SA9.6-1-13-7 JC68-00697A LABEL(R)-HEIGHT,MP;SCX-5312F,-,PC,T0.5,W L0008 SNA9.6-1-1-20 JC70-00369A IPR-BRKT GUIDE DUPLEX;CLP-500,SECC,-,T0. G2103 SNA9.6-1-1-21 JC70-00364A IPR-BRKT GROUND B;CLP-500,SUS304,-,T0.2, K4288 SNA9.6-1-1-22 JC70-00363A IPR-BRKT GROUND A;CLP-500,SUS304,-,T0.2, K4287 SNA9.6-1-1-23 JC70-00366A IPR-BRKT GROUND D;CLP-500,C5210P,-,T0.3, K4290 SNA9.6-1-1-24 JC70-00365A IPR-BRKT GROUND C;CLP-500,SUS304,-,T0.3, K4289 SNA9.6-1-1-25 JC39-00036A CBF HARNESS-OPE GND;SF-5100,#18,UL 1007, H1184 SA9.6-1-1-26 JC72-00730A PMO-BUSHING FEED;SCX-5100,POM,BLACK,-,-, F6161 SA9.6-1-1-27 JC72-01086A PMO-GUIDE LOWER DUPLEX;CLP-500,ABS,BLACK D3035 SNA9.6-1-1-28 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.6-1-1-29 JC72-01085A PMO-GUIDE FEED;CLP-500,POM,BLACK,-,M90-4 F6175 SNA9.6-1-1-30 6031-001051 WASHER-PLAIN;M4,ID4.1,OD7.0,T0.13,*,POLY S2004 SNA9.6-1-1-31 JC61-00866A GUIDE-M-PAPER T2;CLP-500,PC+SUM24L,HB,-, G2072 SA9.6-1-1-32 JC61-00485A SPRING ETC-ACTUATOR6G;SCX-5100,SUS304-WP Z4133 SA9.6-2 JC96-03238A MEA UNIT-T2;CLP-500,SEC,EXPORT,-,-,-,- K3629 SA
9.7-0 JC96-03237A ELA UNIT-DE_DRIVE;CLP-510,SEC,EXPORT,-,- T2073 SA9.7-1 JC61-00972A BRACKET-P-DEVE FRONT;CLP-510,SECC,T1.2,- SNA9.7-2 0205-001003 GREASE-BEARING;NYOGEL788,DAMPING GREASE, SNA9.7-3 JC66-00734A GEAR-DEVE IDLE Z33;CLP-510,POM,M0.8,Z33, G0012 SA9.7-4 JC66-00735A GEAR-DEVE IDLE Z53;CLP-510,POM,M0.8,Z53, G0013 SA9.7-5 JC66-00733A GEAR-DEVE IDLE Z41;CLP-510,POM,M0.8,Z41, G0011 SA9.7-6 JC66-00473B GEAR-M-DEVE IDEL Z51;CLP-500,POM,DE8903, G0563 SA9.7-7 JC66-00469A GEAR-ITB CLEAN RDCN;CLP-500,POM,M90-44,M G0306 SA9.7-8 JC66-00732A GEAR-DEVE RDCN;CLP-510,POM,M0.5/0.8,Z82/ G0010 SA9.7-9 6031-000023 WASHER-PLAIN;-,ID5.9,OD10.0,T0.5,BLK,POL SNA9.7-10 JC66-00739A SHAFT-DEVE DRIVE;CLP-510,SUM24L,L60.3,D6 SNA9.7-11 JC47-00006B MEP-CLUTCH SPRING;-,CLP-510,4.0W,DC24V,0 SNA9.7-12 JC61-00973A BRACKET-P-DEVE REAR;CLP-510,SECC,T1.2,-, SNA9.7-13 6003-000301 SCREW-TAPTITE;BH,+,S,M4,L6,ZPC(YEL),SWRC SNA9.7-14 JC61-00699A BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0 K2874 SA
9.7 Deve Drive Ass'y
4
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.7-15 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.7-16 JC31-00021A MOTOR DC-MAIN(BLDC);50M8432021,CLP-500,1 M0010 SA9.7-17 6003-000301 SCREW-TAPTITE;BH,+,S,M4,L6,ZPC(YEL),SWRC SNA9.7-18 JB70-00168A ICT-PIN ADF;SCX-1110F,STS303,D2.0,-,-,-, A2006 SA9.7-19 JC66-00465A GEAR-DEVE DRIVE 2_Z20;CLP-500,POM,DE8903 G0545 SA9.7-20 6031-001255 WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5, SA9.7-21 JF68-10532B LABEL(P)-BAR CODE;CLP-500,-,YUPO PAPER,1 SNA
9.8-0 JC96-03236A ELA UNIT-MAIN DRIVE;CLP-510,SEC,EXPORT,- D4029 SA9.8-1 JC31-00038A MOTOR DC-MAIN(BLDC);50M843A020,CLP-510,1 M0011 SA9.8-2 JC33-00008B SOLENOID-DUPLEX;-,CLP-500,DC24V,38.4§Ù,3 S8014 SA9.8-3 JC47-00007A MEP-CLUTCH CAM SOLENOID;-,CLP-500,3.1W,D C9046 SA9.8-4 JC47-00008A MEP-CLUTCH ELECTRIC FEED;-,CLP-500,4.0W, C9047 SA9.8-5 JC61-00984A BUSH-M-D8 L5;CLP-510,POM,ID8.0,OD12.0,L5 B0010 SA9.8-6 JC61-00699A BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0 K2874 SA9.8-7 JC61-70915A SPRING ETC-SOLENOID DP;ML-165,SUS304-WPB S8015 SA9.8-8 JC66-00470A GEAR-FEED DRIVE_Z37;CLP-500,POM,DE8903,M F6074 SA9.8-9 JC66-00471A GEAR-FUSER DRIVE 1_Z47;CLP-500,POM,M90-4 D4037 SA9.8-10 JC66-00472A GEAR-FUSER DRIVE 2_Z30;CLP-500,POM,DEL 5 D4038 SA9.8-11 JC66-00473A GEAR-IDLE Z51;CLP-500,POM,DE8903,M0.8,Z5 G0284 SA9.8-12 JC66-00474A GEAR-IDLE Z53;CLP-500,POM,DE8903,M0.8,Z5 G0285 SA9.8-13 JC66-00475A GEAR-ITB DRIVE 1_Z90;CLP-500,POM,DEL 588 D4040 SA9.8-14 JC66-00476A GEAR-ITB DRIVE 2_Z30;CLP-500,POM,DE20028 D4041 SA9.8-15 JC66-00477A GEAR-OPC DRIVE 1_Z120;CLP-500,POM,DE2002 D4043 SA9.8-16 JC66-00479A GEAR-OPC RDCN_Z120/Z60;CLP-500,POM,M90-4 G0356 SA9.8-17 JC66-00480A GEAR-RDCN Z110/Z37;CLP-500,POM,M90-44,M0 G0402 SA9.8-18 JC66-00481A GEAR-RDCN Z62/Z48;CLP-500,POM,M90-44,M0. G0403 SA9.8-19 JC66-00482A GEAR-SWING DRIVE;CLP-500,POM,M90-44,M0.8 D4050 SA9.8-20 JC66-00483A GEAR-T2 DRIVE_Z25;CLP-500,POM,M90-44,M0. D4051 SA9.8-21 JC66-00740A SHAFT-FEED DRIVE;CLP-510,SUM24L,L62.0,D8 SNA9.8-22 JC66-00547A SHAFT-FUSER DRIVE;CLP-500,SUM24L,L62.8,D S4099 SA9.8-23 JC66-00549A SHAFT-ITB DRIVE;CLP-500,SUM24L,L60.5,D8. S4111 SA9.8-24 JC66-00550A SHAFT-OPC DRIVE;CLP-500,SUM24L,L51.8,D8. S4122 SA9.8-25 JC66-00551A SHAFT-T2 CAM;CLP-500,SUM24L,L74.4,D8.0,- S4137 SA9.8-26 JC66-00741A SHAFT-T2 DRIVE;CLP-510,SUM24L,L57.5,D8.0 SNA9.8-27 JC66-40211B GEAR-EXIT/U,ID;ML-1605,POM,M0.8,Z16,-,BL E4045 SA9.8-28 JC70-00341A IPR-BRKT MAIN FRONT;CLP-500,SECC,-,T1.2, K3281 SA9.8-29 JC70-00344A IPR-BRKT MAIN REAR;CLP-500,SECC,-,T1.2,- K3282 SA9.8-30 JC70-00346A IPR-LINK SOLENOID;CLP-500,SECC,-,T1.6,-, S8011 SA9.8-31 JC72-01064A PMO-HUB CLUTCH;CLP-500,POM,BLACK,-,DE890 C9067 SA9.8-32 JC72-01232A PMO-DUMMY CLUTCH;CLP-500,POM,WHITE,-,DEL C9065 SA9.8-33 6031-000023 WASHER-PLAIN;-,ID5.9,OD10.0,T0.5,BLK,POL SNA9.8-34 JG74-10541A MPR-RING CHARGE;SF6000,POLYSLIDER,OD10,I W3388 SA9.8-35 6031-001255 WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5, SA9.8-36 6044-000159 RING-C;ID3,OD7,T0.6,PASS,STSC R0006 SA9.8-37 6044-000231 RING-E;ID5.0,OD11.0,T0.6,PASS,STS304 SA9.8-38 JB70-00168A ICT-PIN ADF;SCX-1110F,STS303,D2.0,-,-,-, A2006 SA9.8-40 JF68-10532B LABEL(P)-BAR CODE;CLP-500,-,YUPO PAPER,1 SNA
9.9-0 JC96-03239A ELA UNIT-FUSER 230V;CLP-510,SEC,EXPORT,2 F1940 SA9.9-1 JC66-00517A ROLLER-PRESSURE;CLP-510,AL5052+SILICON,D SNA9.9-2 JC72-01058A PMO-BEARING FUSER F;CLP-500,PPS,BLACK,T5 B0029 SNA9.9-3 JC72-01059A PMO-BEARING FUSER GEAR;CLP-500,PPS,BLACK B0030 SNA9.9-4 JC66-00510A GEAR-FUSER_Z35;CLP-500,PPS,M1.0,Z35,-,OF F4095 SA
9.8 Main Drive Ass'y
9.9 Fuser Ass'y
5
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.9-5 6107-001193 SPRING-CS;SUS304-WPB,YEL,PI1.1,D6.1,L19. S0032 SNA9.9-6 JC72-01061A PMO-FUSER UPPER;CLP-500,PET+GF30%,BN9030 F0004 SNA9.9-7 JC72-01062A PMO-FUSER LOWER;CLP-500,PET+GF30%,BN9030 F0005 SNA9.9-8 JC70-00355A IPR-GROUND FUSER;MLC-500,SUS304 CSP 1/2H G0037 SNA9.9-9 JC71-00043A NPR-ELECTRODE AC WIRE;-,CLP-500,C5210P,- E0003 SNA9.9-10 JC71-00047A NPR-ELECTRODE GEAR;-,CLP-500,C5210P,T0.6 E0004 SNA9.9-11 JC71-00048A NPR-ELECTRODE M;-,CLP-500,C5210P,T0.6,-, E0005 SNA9.9-12 4712-000001 THERMOSTAT;125/250V,15/7.5A,150+-5C,0C,2 T0007 SA9.9-13 JC71-00046A NPR-ELECTRODE F;-,CLP-500,C5210P,T0.6,-, E0006 SNA9.9-14 JC71-00049A NPR-ELECTRODE PR;-,CLP-500,C5210P,T0.6,- E0007 SNA9.9-15 JC71-00044A NPR-ELECTRODE AC PLATE;-,CLP-500,C5210P, E0008 SNA9.9-16 JC72-01055A PMO-COVER THERMOSTAT;CLP-500,PET+GF30%,B C0058 SNA9.9-17 JC72-01060A PMO-COVER CLEANING;CLP-500,PET+GF30%,BN9 C0059 SNA9.9-18 JC66-00608A ROLLER-EXIT IDLE;CLP-500,TEFLON,PI10.5,L R0010 SNA9.9-19 JC72-20901A PEX-ROLLER EXIT F_UP;ML-5000A,TEFLON,WHI E4091 SA9.9-20 JC72-01100A PMO-GUIDE DP SIDE;CLP-500,PC,BLACK,-,HH1 G0038 SNA9.9-21 JC71-00045A NPR-ELECTRODE CONNECTOR;-,CLP-500,C5210P C0060 SNA9.9-22 4713-001176 LAMP-HALOGEN;230V,-,500W,-,-,-,10X295.3M L0017 SA9.9-23 4713-001175 LAMP-HALOGEN;230V,-,300W,-,-,-,10X293MM L0015 SA9.9-24 JC66-00742A LEVER-M-ACTUATOR EXIT;CLP-510,PET+GF30%, SNA9.9-25 6107-001205 SPRING-TS;SUS304-WPB,-,PI0.45,D7.95,L9.3 S0033 SNA9.9-26 JC72-01063A PMO-GUIDE OUTPUT;CLP-500,PET+GF30%,BN903 G0039 SNA9.9-27 1404-001310 THERMISTOR-NTC;3.161KOHM,-,4537K,0.3MW/C T0008 SA9.9-28 6021-001194 NUT-SQUARE;-,M3,PASS,SWCH+ZN COATING,SQU SNA9.9-29 JC68-00407A LABEL(R)-HV FUSER;ML-6060,PVC,-,220V,- L0018 SNA9.9-30 JC72-01208A PMO-GUIDE INPUT;CLP-500,PET+GF30%,BLACK, G0040 SNA9.9-31 JC75-00165A MEC-DUMMY THERMISTOR;CLP-500,-,PPS+SUS30 SNA9.9-33 JC72-01208A PMO-GUIDE INPUT;CLP-500,PET+GF30%,BLACK, G0040 SNA
9.10-0 JC97-01753A MEA-CASSETTE;CLP-500,-,KOREA,CASSETTE,-, K3657 SA9.10-1 JC72-01069A PMO-FRAME CASSETTE;CLP-500,HIPS,LIGHT GR C4024 SNA9.10-2 JC72-01068A PMO-COVER CASSETTE;CLP-500,ABS,LIGHT GRA Z2546 SNA9.10-3 JC72-01072A PMO-GUIDE SIDE CST;CLP-500,HIPS,VIOLET B K3926 SNA9.10-4 JC72-01070A PMO-GUIDE FRONT CST;CLP-500,HIPS,LIGHT G K3898 SNA9.10-5 JC72-01071A PMO-GUIDE REAR;CLP-500,HIPS,VIOLET BLUE, K3917 SNA9.10-6 JC70-00357A IPR-PLATE K/UP;CLP-500,SECC,-,T1.0,-,-,- K3372 SA9.10-7 JC70-00220A IPR-FINGER;SCX-5100,SPCC,-,T1.2,-,-,-,-, F0003 SA9.10-8 JC70-00358A IPR-SPRING PLATE G/SIDE;CLP-500,SUS301,- P5091 SA9.10-9 JC70-00356A IPR-GUIDE PLATE PAPER;CLP-500,SUS304,-,T P5060 SA9.10-10 6107-001200 SPRING-CS;SUS304-WPB,-,PI0.85,D21.85,L55 S0034 SNA9.10-11 JG61-70531A SPRING ETC-LOCKER,PLATE;SF6000,STS304WPB Z4215 SA9.10-12 JC72-01073A PMO-LOCKER PLATE;CLP-500,POM,WHITE,-,M90 L6038 SA9.10-13 JC73-10910A RPR-PAD CST;ML-165,CORK,25.8*24.6,-,-,NT K4243 SA9.10-14 JC68-01174A LABEL(P)-INSTRUCTION CST;CLP-500,-,YUPO SNA9.10-15 JC68-00516A LABEL(R)-HEIGHT XEROX;ML-6060/XRX,-,ART L0040 SNA
9.13-0 JC97-02037A MEA MAIN-FRAME;CLP-510,SEC,EXPORT,-,-,-, F1941 SA9.13-1 JC97-01834A MEA UNIT-OPC TONER DUCT;CLP-500,SEC,EXPO D1008 SA9.13-1-1 JC96-02882A ELA UNIT-TONER MOTOR;CLP-500,SEC,EXPORT, M2107 SA9.13-1-1-1 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.13-1-1-2 JB31-00020B MOTOR DC-WASTE TONER;HC385G,CLP-500,160M T2141 SA9.13-1-1-3 JC61-00808A BRACKET-WASTER TONER MOTOR;CLP-500,SECC, M2050 SNA9.13-1-1-4 JC66-00653A GEAR WORM-WHEEL IDLE;CLP-500,POM,M0.6,Z3 G0137 SA9.13-1-1-5 JC66-00654A GEAR WORM-WASTE TONER;CLP-500,POM,M0.6,Z T2098 SA
9.10 Cassette Ass'y
9.13 Main Frame
6
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.13-1-2 6031-000023 WASHER-PLAIN;-,ID5.9,OD10.0,T0.5,BLK,POL SNA9.13-1-3 JC61-00699A BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0 K2874 SA9.13-1-4 JC61-00810A PLATE-VIBRATOR INLET;CLP-500,SUS304 1/2H P5159 SNA9.13-1-5 JC61-00820A BASE-M-WASTE TONER;CLP-500,PC/ABS,-,-,-, T2015 SNA9.13-1-6 JC62-00129A PIPE-WASTE BAR;CLP-500,SILICON,ID1.0,OD5 W1003 SA9.13-1-7 JC66-00649A CAM-M-WASTE DUCT OUTLET;CLP-500,POM,-,-, D1001 SA9.13-1-8 JC66-00651A GEAR WORM-WHEEL Z35;CLP-500,POM,M0.6,Z33 G0137 SA9.13-1-9 JC66-00652A SHAFT-M-WASTE DUCT INLET;CLP-500,POM,-, D1011 SA9.13-1-10 JC67-00052A DUCT-M-WASTE LIFTER;CLP-500,HIPS,-,-,-,B D1002 SA9.13-1-11 JC67-00053A DUCT-M-WASTE TONER INLET1;CLP-500,HIPS,- D1003 SA9.13-1-12 JC67-00054A DUCT-M-WASTE TONER INLET2;CLP-500,PC/ABS D1004 SA9.13-1-13 JC72-01186A PMO-PIPE WASTE TRANSFER;CLP-500,HDPE,TRP W1006 SNA9.13-1-14 JC72-01278A SPONGE-WASTE LIFTER 1;CLP-500,PE FORM+PE Z3020 SA9.13-1-15 JC72-01279A SPONGE-WASTE LIFTER 2;CLP-500,PE FORM+PE Z3021 SA9.13-1-16 JC72-01285A SPONGE-WASTE DUCT OPC;CLP-500,PE FOAM,-, D1012 SA9.13-1-17 JC72-01290A SPONGE-WASTE COVER;CLP-500,PE FOAM+PET F Z3019 SA9.13-1-18 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.13-1-19 6107-001201 SPRING-CS;SWRS-82A,-,W0.8*H0.8,D7.4,L280 S0047 SNA9.13-1-20 6107-001199 SPRING-CS;SUS304-WPB,-,PI0.32,D3.95,L27, S0048 SNA9.13-1-21 JC39-00299A CBF HARNESS-WASTE_MOTOR;CLP-500,WIRE HAR M2056 SA9.13-3 JC97-01810B MEA UNIT-LSU GUIDE BRKT;CLP-510,SEC,EXPO SNA9.13-3-4 JC70-00428A IPR-PLATE OPC OEM;CLP-500,SUS304 1/2H,-, O0023 SNA9.13-3-1 JC70-00388A IPR-BRKT LSU;CLP-500,SECC,-,T1.6,-,-,-,- L7020 SNA9.13-3-2 JC72-01169A PMO-LSU BASE;CLP-500,HIPS,BLACK,-,HR-136 L7037 SNA9.13-3-3 JC70-00444A IPR-GROUND LSU;CLP-500,SUS304-1/2H,-,T0. L7022 SNA9.13-3-5 JC75-00049A MEC-TERMINAL;SF-5100,SAMSUNG,IVR K3739 SA9.13-3-6 JC72-01146A PMO-COVER OEM UPPER;CLP-500,HIPS,BLACK,- Z2643 SNA9.13-3-7 JC39-00229A CBF HARNESS-OPC_FUSE;SCX-5312F,WIRE HARN H0023 SA9.13-5 JC97-02038A MEA UNIT-BRKT HVPS;CLP-510,SEC,EXPORT,-, SNA9.13-5-1 JC61-00975A GUIDE-M-HVPS BOARD;CLP-510,HIPS,HB,-,-,- SNA9.13-5-2 JC70-00386A IPR-BRKT HVPS LOWER;CLP-500,SECC,-,T1.0, S7029 SNA9.13-5-3 6502-000132 CABLE CLAMP;DAWS-1NE,ID11,L21.0,NTR,NYLO C0069 SA9.13-5-4 6502-000121 CABLE CLAMP;DAMC-101,D7~8,L19,SCP-1,NTR C0071 SNA9.13-5-5 JC63-00234A SHEET-HVPS;MLC-500,PC,T=0.5,W136,L250,-, S0005 SNA9.13-6 JC96-02797A ELA UNIT-GUIDE PAPER T2;CLP-500,SEC,EXPO K3128 SA9.13-7 JC96-02795A ELA UNIT-DUMMY FUSER BASE;CLP-500,SEC,EX D2014 SA9.13-8 JC96-03216A ELA UNIT-ITB CAM;CLP-510,SEC,EXPORT,ITB I2131 SA9.13-9 JC96-02881A ELA UNIT-FRAME BASE;CLP-510,SEC,EXPORT,- B0075 SA9.13-10 JC96-03215A ELA UNIT-FRAME REAR;CLP-510,SEC,EXPORT,- F8823 SA9.13-11 JC96-03214A ELA UNIT-FRAME FRONT;CLP-510,SEC,EXPORT, F8822 SA9.13-13 JC70-00447A IPR-SHUTTER TORTION;CLP-500,SUS304-H,-,T S6004 SNA9.13-14 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.13-16 JC72-01284A SPONGE-DUST OPC COVER;CLP-500,PE FOAM,-, O0060 SA9.13-17 JC97-01814A MEA UNIT-OPC TONER HOUSING;CLP-500,SEC,E H6050 SA9.13-17-1 JC61-00885A PLATE-P-VIBRATOR OUTLET;CLP-500,SUS304-H SNA9.13-17-2 JC61-00812A BUSH-M-WASTE CAM;CLP-500,POM,-,-,-,WHITE W1000 SA9.13-17-3 JC72-01222A PMO-CAP SHUTTER ITB;CLP-500,HIPS,BLACK,- S6006 SNA9.13-17-4 JC72-01228A PMO-HOUSING TRANSFER;CLP-500,HIPS,BLACK, H6087 SNA9.13-17-5 JC72-01230A PMO-SHUTTER TRANSFER OPC;CLP-500,HIPS,BL O0051 SNA9.13-17-6 JC72-01289A SPONGE-TANK TONER;CLP-500,PE FOAM,-,T3.0 S0053 SNA9.13-17-8 JC72-01294A SPONGE-DUCT TONER OPC;CLP-500,PE FOAM+PE D0016 SNA9.13-17-9 JC72-01295A SPONGE-TANK TONER OPC;CLP-500,PE FOAM+PE S0055 SNA9.13-18 JB61-70922A SPRING ETC-CLUTCH;MJC-810L,SUS304,-,ID4. SA9.13-20 JC96-03244A ELA UNIT-DEVE BOARD;CLP-510,-,EXPORT,DEV P2136 SA9.13-21 JC39-00276A CBF HARNESS-MAIN FSR_ROLL;CLP-500,WIRE H H1126 SA9.13-22 JC39-00398A CBF HARNESS-PANEL;CLP-600,WIRE HARNESS,U H2133 SA
7
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.13-23 JC63-00165A GROUND-FUSER FRAME;CLP-500,SUS304CSP,T0. F2125 SNA9.13-24 JC63-00247A SHEET-ERASER LAMP;CLP-500,PC,T0.5,W220.5 L1033 SA9.13-25 JC66-00334A GEAR-GEAR FUSER DRV OUTER;SCX-5100,POM,M F4097 SA9.13-26 JC66-40911A GEAR-DP,IDLE;ML-165,POM,M1.0,Z21,-,WHITE G0198 SA9.13-27 JC66-40964A GEAR-EXIT,IDLE(Z17);ML-5000,NYLON66,M1.0 E4040 SA9.13-28 JC61-00984A BUSH-M-D8 L5;CLP-510,POM,ID8.0,OD12.0,L5 B0010 SA9.13-29 JC72-01141A PMO-COVER FUSER BASE;CLP-500,PBT+GF30%,B Z2608 SNA9.13-30 JC72-01145A PMO-COVER HARNESS FUSER;CLP-500,HIPS,BLA H1327 SNA9.13-31 JC72-01171A PMO-LSU SHUTTER COVER;CLP-500,PP,BLACK,- L7038 SNA9.13-32 JC97-02138A MEA UNIT-TERMINAL S;CLP-510,SEC,EXPORT,S T2333 SA9.13-33 JC63-00360A SHEET-TONER COVER;CLP-500,PVC,T0.1,W65,L SNA9.13-34 JC72-01216A PMO-HOLDER GUIDE EXIT UP;CLP-500,POM,BLA G2268 SA9.13-35 JC47-00007B MEP-CLUTCH CAM SOLENOID;-,CLP-500,3.1W,D C2222 SA9.13-36 JC72-01216A PMO-HOLDER GUIDE EXIT UP;CLP-500,POM,BLA G2268 SA
9.14-0 JC96-03214A ELA UNIT-FRAME FRONT;CLP-510,SEC,EXPORT, F8822 SA9.14-1 JC96-03234A ELA UNIT-TONER SENSOR;CLP-510,SEC,EXPORT SNA9.14-1-1 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.14-1-2 JC61-00813A HOLDER-M-WASTE TONER SENSOR;CLP-500,HIPS H4038 SA9.14-1-3 JC72-01189A PMO-TONER DETACTER;CLP-500,HIPS,BLACK,-, T2162 SA9.14-1-4 JC92-01637A PBA SUB-EXIT_WASTE;CLP-510,SEC,KOREA,WAS W2121 SA9.14-2 JC97-01812A MEA UNIT-ITB LIFTER;CLP-500,SEC,EXPORT,- K3579 SA9.14-2-1 JC72-01282A SPONGE-DUCT TONER ITB LIFT;CLP-500,PE FO L0028 SNA9.14-2-2 JC67-00043A DUCT-TONER ITB LIFTER;CLP-500,HIPS,-,-,- D1005 SNA9.14-2-3 JC72-01286A SPONGE-ITB DUCT;CLP-500,PE FOAM,-,T1.0,W D0015 SNA9.14-3 JC97-01813A MEA UNIT-ITB TONER HOUSING;CLP-500,SEC,E H6049 SA9.14-4 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.14-6 JC61-00709A PLATE-GUIDE T2 FRONT;CLP-500,SECC,T1.0,- P5141 SNA9.14-7 JC61-00756A BRACKET-DUMMY LSU F;CLP-500,SECC,T1.2,-, L7001 SNA9.14-3-1 JC61-00814A HOUSING-M-WASTE TONER ITB;CLP-500,HIPS,H H6037 SA9.14-3-2 JC72-01294A SPONGE-DUCT TONER OPC;CLP-500,PE FOAM+PE D0016 SNA9.14-3-3 JC72-01222A PMO-CAP SHUTTER ITB;CLP-500,HIPS,BLACK,- S6006 SNA9.14-3-4 JC72-01229A PMO-SHUTTER TRANSFER ITB;CLP-500,HIPS,BL S6009 SNA9.14-3-5 JC72-01287A SPONGE-ITB TANK DUST;CLP-500,PE FOAM+PET S0060 SNA9.14-3-6 JC72-01288A SPONGE-ITB TANK TONER;CLP-500,PE FOAM+PE S0061 SNA9.14-3-7 JC72-01292A SPONGE-CAP SHUTTER;CLP-500,PE FOAM,-,T2. S0054 SNA9.14-3-7 JC72-01292A SPONGE-CAP SHUTTER;CLP-500,PE FOAM,-,T2. S0054 SNA9.14-8 JC97-02138A MEA UNIT-TERMINAL S;CLP-510,SEC,EXPORT,S T2333 SA9.14-9 JC63-00166A GROUND-HVPS LSU;CLP-500,SUS304 1/2H,T0.2 L7016 SNA9.14-10 JC66-00562A LINK-LOCK OPC F;CLP-500,POM,M90-44,-,-,- O0028 SNA9.14-11 JC66-00666A LEVER-ITB LOCK FRONT;CLP-500,PC/ABS,T3.0 L4032 SA9.14-12 JC68-01149B LABEL(R)-COLOR BAR;CLP-510,SEC,PVC,T0.12 SNA9.14-13 JC39-00114A CBF HARNESS-BRUSH GND;ML-7050,-,UL1007,- H1037 SA9.14-14 JC70-00385A IPR-BRKT GUIDE HVPS R;CLP-500,SECC,-,T1. G2105 SNA9.14-15 JC70-00406A IPR-BRKT EXIT HINGE F;CLP-500,SECC,-,T1. H3023 SNA9.14-16 JC70-00419A IPR-ITB HINGE GROUND;CLP-500,SUS304 1/2H H3033 SNA9.14-17 JC70-00420A IPR-ITB GUIDE TORSION;CLP-500,SUS304 H,- G2128 SNA9.14-18 JC70-00421A IPR-OPC GUIDE TORSION;CLP-500,SUS304 1/2 G2129 SNA9.14-19 JC70-00422A IPR-OPC/ITB GROUND;CLP-500,SUS304 1/2H,- K3364 SNA9.14-21 JC70-00424A IPR-OPC/LSU GROUND;CLP-500,SUS304 1/2H,- L7023 SNA9.14-22 JC70-00447A IPR-SHUTTER TORTION;CLP-500,SUS304-H,-,T S6004 SNA9.14-23 JC72-01144A PMO-FRAME FRONT;CLP-500,ABS+GF20%,BLACK, F2227 SNA9.14-24 JC72-01173A PMO-COVER TOP LEVER IN;CLP-500,PC+GF20%, L4043 SNA9.14-25 JC72-01174A PMO-COVER TOP LEVER OUT;CLP-500,PC+GF20% L4044 SNA9.14-26 JC72-01177A PMO-DEVE OPEN PLATE;CLP-500,HIPS,BLACK,- O1079 SNA
9.14 Front Frame
8
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.14-27 JC72-01178A PMO-DEV OPEN PLATE GUIDE;CLP-500,HIPS,BL G2166 SNA9.14-28 6107-001196 SPRING-CS;SUS304-WPB,-,PI0.85,D5.65,L21. S0063 SA9.14-29 JC72-01184A PMO-LOCK ITB FRONT;CLP-500,POM,BLACK,-,M K4044 SNA9.14-30 JC72-01185A PMO-LOCK COVER FRONT;CLP-500,HIPS,BLACK, Z2790 SNA9.14-31 JC72-01221A PMO-RACK OPC;CLP-500,POM,BLACK,-,M90-44, O0046 SNA9.14-32 6107-001199 SPRING-CS;SUS304-WPB,-,PI0.32,D3.95,L27, S0048 SNA9.14-33 JC72-01225A PMO-GUIDE LOCK OPE F;CLP-500,PC ,BLACK,- O1083 SNA9.14-34 JC72-01283A SPONGE-DUST ITB COVER;CLP-500,PE FOAM,-, Z3017 SA9.14-36 JC92-01631A PBA SUB-OEM_BB_PLUS;CLP-510,SEC,KOREA,OE P2133 SA9.14-37 6107-001214 SPRING-ES;SWP(PW-2),BLACK,PI0.45,D5.35,L S0065 SA
9.15-0 JC96-03215A ELA UNIT-FRAME REAR;CLP-510,SEC,EXPORT,- F8823 SA9.15-1 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.15-2 JC39-00264A CBF HARNESS-HVPS_CHARGE;CLP-500,WIRE HAR H1099 SA9.15-3 JC39-00265A CBF HARNESS-HVPS_T1;CLP-500,WIRE HARNESS H1101 SA9.15-4 JC39-00266A CBF HARNESS-HVPS_T2;CLP-500,WIRE HARNESS H1102 SA9.15-5 JC97-01829A MEA UNIT-FEED;CLP-500,SEC,EXPORT,-,-,-,- F6112 SA9.15-6 JC61-00707A PLATE-S/W DUPLEX;CLP-500,SUS304 1/2H,T0. P5156 SNA9.15-7 JC61-00708A PLATE-GUIDE T2 REAR;CLP-500,SECC,T1.0,-, P5142 SNA9.15-8 JC63-00162A GROUND-MAIN ITB DEVE;CLP-500,SUS304 H,T0 T2110 SNA9.15-9 JC63-00163A GROUND-LSU DEVE DRIVE;CLP-500,SUS304 H,T L7018 SNA9.15-10 JC63-00181A GROUND-HVPS LSU LOWER;CLP-500,C5210P-1/2 L7017 SNA9.15-11 JC63-00208A GROUND-EXIT DRIVE;CLP-500,SUS304-1/2H,T0 D4052 SNA9.15-12 JC66-00343A GEAR-RDCN FEED OUTER;SCX-5100,POM,M90-44 F6086 SA9.15-13 JC66-00484A GEAR-T2 IDEL_Z27;CLP-500,POM,DE8903,M0.8 G0432 SA9.15-14 JC66-00485A GEAR-T2 RDCN_Z32/Z23;CLP-500,POM,M90-44, G0433 SA9.15-15 JC66-00667A LEVER-ITB LOCK REAR;CLP-500,PC/ABS,T3.0, L4033 SA9.15-16 JC70-00381A IPR-BRKT DUMMY LSU R;MLC-500,SECC,-,T1.6 L7019 SNA9.15-17 JC70-00384A IPR-BRKT GUIDE HVPS F;CLP-500,SECC,-,T1. G2104 SNA9.15-18 JC70-00387A IPR-BRKT LOCK ITB;CLP-500,SECC,-,T1.6,-, K3280 SNA9.15-19 JC70-00407A IPR-BRKT EXIT HINGE R;CLP-500,SECC,-,T1. H3024 SNA9.15-20 JC70-00425A IPR-PLATE FUSER;CLP-500,SUS304 1/2H,-,T0 F4107 SNA9.15-22 JC70-00427A IPR-PLATE OPC HV;CLP-500,SUS304 1/2H,-,T O0022 SNA9.15-23 JC70-00431A IPR-PLATE T1;CLP-500,SUS304 1/2H,-,T0.4, K3379 SNA9.15-24 JC70-00432A IPR-PLATE T2;CLP-500,SUS304 1/2H,-,T0.4, K3380 SNA9.15-25 JC70-00443A IPR-GROUND HVPS;CLP-500,C5210P-1/2H,-,T0 S7032 SNA9.15-26 JC70-00445A IPR-GROUND MAIN;CLP-500,SUS304-1/2H,-,T0 K3328 SNA9.15-27 JC72-01143A PMO-FRAME REAR;CLP-500,ABS+GF20%,BLACK,- F2254 SNA9.15-28 JC72-01148A PMO-COVER T1 HV;CLP-500,HIPS,BLACK,-,HR- Z2710 SNA9.15-29 JC72-01149A PMO-COVER T2 HV;CLP-500,HIPS,BLACK,-,HR- Z2711 SNA9.15-30 JC72-01157A PMO-GUIDE LOCK OPC;CLP-500,PC+GF20%,BLAC O0043 SNA9.15-31 JC72-01158A PMO-LINK LOCK OPC;CLP-500,POM,BLACK,-,M9 O0045 SNA9.15-32 JC72-01168A PMO-LOCK ITB;CLP-500,POM,BLACK,-,M90-44, K4045 SNA9.15-33 JC70-00446A IPR-GROUND PAPER GUIDE;CLP-500,SUS304-1/ G2110 SNA9.15-34 JC75-00049A MEC-TERMINAL;SF-5100,SAMSUNG,IVR K3739 SA9.15-35 JC39-00302A CBF HARNESS-100M_GND;CLP-500,-,-,1 PIN,5 H1015 SA9.15-36 JC96-02876A ELA UNIT-COVER OPEN SENSOR;CLP-500,SEC,E Z2296 SA9.15-36A JC61-00706A PLATE-S/W DEVE;CLP-500,SUS304 1/2H,T0.2, P5155 SNA9.15-36B JC70-00413A IPR-BRKT DEVE OPEN;CLP-500,SECC,-,T1.2,- O1045 SNA9.15-37 6107-001214 SPRING-ES;SWP(PW-2),BLACK,PI0.45,D5.35,L S0065 SA9.15-38 6107-001196 SPRING-CS;SUS304-WPB,-,PI0.85,D5.65,L21. S0063 SA
9.16-0 JC96-02881A ELA UNIT-FRAME BASE;CLP-500,SEC,EXPORT,- B0075 SA9.16-1 JC96-02774A ELA UNIT-MP;CLP-500,SEC,EXPORT,-,-,-,- K3155 SA
9.15 Rear Frame
9.16 Base Frame
9
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.16-2 JC97-01755A MEA-PICKUP;CLP-500,SEC,EXPORT,-,-,-,- P2104 SA9.16-3 JC39-00082A CBF HARNESS-SCF;ML-6060,WIRE HARNESS,UL1 H1227 SA9.16-4 JC39-00280A CBF HARNESS-SMPS_INLET;CLP-500,WIRE HARN H1252 SA9.16-5 JC61-00710A PLATE-GUIDE RAIL;CLP-500,SUS304 1/2H,T0. P5140 SNA9.16-6 JC61-40001A FOOT-ML80;ML-80,NBR,-,GRAY,-,-,- F1013 SA9.16-7 JC63-00167A GROUND-SCF;CLP-500,SECC,T0.8,-,-,-,- S1039 SNA9.16-8 JC63-00175A COVER-SCREW LOCKING MP;CLP-500,POM,-,-,- S2019 SNA9.16-9 JC63-00207A COVER-M-BASE BAR;CLP-500,HIPS,-,-,-,HB,- Z2178 SA9.16-10 JC66-00050A CAM-CATCH;ML-9400W,POM,-,34¡¿18¡¿7,WHITE S K2892 SA9.16-11 JC66-00335A GEAR-PICK_UP;SCX-5100,POM,M0.8,Z47,-,NTR P2056 SA9.16-12 JC70-00379A IPR-BRKT BASE BAR;CLP-500,SECC,-,T1.6,-, B0083 SA9.16-13 JC70-00390A IPR-CHANNEL FRAME BASE;CLP-500,SECC,-,T1 B0086 SA9.16-14 JC70-00404A IPR-BRKT DEVE HINGE F;CLP-500,SECC,-,T1. H3021 SA9.16-15 JC70-00405A IPR-BRKT DEVE HINGE R;CLP-500,SECC,-,T1. H3022 SA9.16-16 JC70-00414A IPR-BRKT POWER;CLP-500,SECC,-,T1.2,-,-,- K3287 SNA9.16-17 JC72-00836A PPR-SHEET/GUIDE PAPER;SCX-5100,PC SHEET, S5048 SA9.16-18 JC72-01156A PMO-FRAME BASE;CLP-500,HIPS,L/GRAY,G7131 B0145 SA9.16-19 JC72-01161A PMO-GUIDE SCT PAPER;CLP-500,HIPS,IVORY,- K3924 SA9.16-20 JC72-01172A PMO-PAPER GUIDE;CLP-500,HIPS,IVORY,-,HR- G2279 SNA9.16-21 JC72-41191A PMO-BEARING SHAFT;ML-6000,POM,BLACK,-,DE S4068 SA9.16-22 JC33-00007B SOLENOID-PICK UP;-,CLP-500,DC24V,80.0§Ù, P2163 SA9.16-23 JC92-01535A PBA SUB-TEMP;CLP-500,SEC,-,TEMP,-,-,-,-, M0429 SA9.16-24 6031-001255 WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5, SA9.16-25 JB39-00103A CBF HARNESS-LIU GND;SCX-1110F,WIRE,UL100 L5004 SA9.16-26 6031-000120 WASHER-E.T;M4,ID4.3,OD8.5,T0.45,ZPC(YEL) SNA
9.17-0 JC96-02774A ELA UNIT-MP;CLP-500,SEC,EXPORT,-,-,-,- K3155 SA9.17-1 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.17-2 JC33-00006B SOLENOID-MP;-,CLP-500,DC24V,82.0§Ù,27.8* S8014 SA9.17-3 JC61-00003A SPRING ETC--CAM MP;ML-6100,SUS304-WPB,0. Z4145 SA9.17-4 JC61-00482A SPRING ETC-PICKUP;SCX-5100,SUS304-WPB,PI P2913 SA9.17-5 JC61-00483A SPRING ETC-KNOCKUP,MP;SCX-5100,SUS304-WP Z4206 SA9.17-6 JC70-00237A IPR-BRACKET SOLENOIDE;SCX-5100,SECC,-,1. S8009 SA9.17-7 JC72-00055A PMO-HOLDER CAM MPF;ML-6100,POM,WHT,-,- K3984 SNA9.17-8 JC72-00761A PMO-ROLLER CAM.MP;SCX-5100,POM,WHITE,-,- K4061 SA9.17-9 JC72-00767A PMO-ACTUATOR,MP;SCX-5100,PC,BLACK,-,-,-, K3818 SA9.17-10 JC72-00768A PMO-ADJUSTER,MP;SCX-5100,POM,BLACK,-,-,- A3001 SA9.17-11 JC72-00769A PMO-CAM PICK UP,MP;SCX-5100,PC,BLACK,-,- P2124 SA9.17-12 JC72-00770A PMO-FRAME,MP;SCX-5100,PC/ABS,C8723,-,-,H F2243 SA9.17-13 JC72-00771A PMO-HOLDER PAD,MP;SCX-5100,PC/ABS,BLACK, P0029 SA9.17-14 JC72-00772A PMO-HOLDER SENSOR,MP;SCX-5100,ABS,BLACK, S3083 SA9.17-15 JC72-00773A PMO-HOUSING PICK UP,MP;SCX-5100,POM,BLAC P2129 SA9.17-16 JC72-00775A PMO-PLATE KNOCK UP,MP;SCX-5100,ABS+GF20% K5007 SA9.17-17 JC72-41027A PMO-IDLE PICK UP MP;ML-165,POM,BLK,-,-,- P2131 SA9.17-18 JC72-41364A PMO-BUSHING_P/U,MP;ML-6100,POM,BLACK,-,C K3855 SA9.17-19 JC73-00089A RPR-RUBBER PICK UP,MP;SCX-5100,EPDM,-,-, P2147 SA9.17-20 JC69-00494A PAD-MP(PLUS);SCX-5315F,URETHANE,0.9T,31, M0005 SA9.17-22 JC92-01500A PBA SUB-MP_EMPTY SENSOR;CLP-500,SEC,-,MP M0396 SA9.17-23 JC72-00056A PMO-GEAR P/U MPF;ML-6100,POM,WHT,-,- G0509 SA9.17-24 JC63-00240A SHEET-PAPER MP;CLP-500,PC,T=0.25,W15,L38 S5084 SA
9.18-0 JC97-01755A MEA-PICKUP;CLP-500,SEC,EXPORT,-,-,-,- P2104 SA9.18-1 JC61-00482A SPRING ETC-PICKUP;SCX-5100,SUS304-WPB,PI P2913 SA9.18-2 JC70-00359A IPR-GROUND FEED;CLP-500,C5210P,-,T0.2,-, F6093 SA
9.17 MP Ass'y
9.18 Pick_Up Ass'y
10
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.18-3 JC70-00360B IPR-GUIDE-P-INPUT;CLP-510,SECC,-,T0.5,-, SNA9.18-6 JC72-00719A PMO-ACTUATOR EMPTY;SCX-5100,-,ABS,BLK,HB K3816 SA9.18-7 JC72-00729A PMO-SHAFT PICK UP;SCX-5100,PC,BLACK,-,-, P2134 SA9.18-8 JC72-01076A PMO-GUIDE PAPER;CLP-500,HIPS,BLACK,-,HB, K3913 SA9.18-9 JC92-01453A PBA SUB-P.EMPTY SENSOR;CLP-500,SEC,-,P.E M0405 SA9.18-10 JC72-41191A PMO-BEARING SHAFT;ML-6000,POM,BLACK,-,DE S4068 SA9.18-11 JC72-41364A PMO-BUSHING_P/U,MP;ML-6100,POM,BLACK,-,C K3855 SA9.18-12 JC73-00149A RUBBER-PICK UP;CLP-500,EDPM,R20.0*W12,-, P2148 SA
9.19-0 JC97-01829A MEA UNIT-FEED;CLP-500,SEC,EXPORT,-,-,-,- F6112 SA9.19-1 JC97-01768A MEA-HOLDER PINCH C3;CLP-500,SEC,EXPORT,- P4004 SA9.19-1-1 JC72-01107A PMO-HOLDER PINCH C3;CLP-500,PC+GF20%,CP2 P4012 SNA9.19-1-2 JC72-01108A PMO-HOLDER PINCH C5;CLP-500,PC+GF20%,CP2 P4012 SNA9.19-1-3 JC70-10230A IPR-SHAFT FEED IDLER;ML-80,SUM24L,NI,-,- F6099 SA9.19-2 JC97-01769A MEA-HOLDER PINCH C5;CLP-500,SEC,EXPORT,- P4005 SA9.19-2-1 JC72-01108A PMO-HOLDER PINCH C5;CLP-500,PC+GF20%,CP2 P4012 SNA9.19-2-2 JC72-40261A PMO-ROLLER FEED L;ML-80,POM,WHT,-,-,-,-, F6192 SA9.19-2-3 JC70-10230A IPR-SHAFT FEED IDLER;ML-80,SUM24L,NI,-,- F6099 SA9.19-3 JC97-01770A MEA-HOLDER PINCH M;CLP-500,SEC,EXPORT,-, P4006 SA9.19-3-1 JC72-00724A PMO-HOLDER PINCH M;SCX-5100,PC+GF20%,BLA P4012 SA9.19-3-2 JC72-40261A PMO-ROLLER FEED L;ML-80,POM,WHT,-,-,-,-, F6192 SA9.19-3-3 JC72-40266A PMO-SUB HOLDER FEED;ML-80,POM,BLK,-,-,-, F6198 SA9.19-3-4 JC72-40262A PMO-ROLLER FEED S;ML-80,POM,NTR,-,- F6194 SA9.19-3-5 JC70-10230A IPR-SHAFT FEED IDLER;ML-80,SUM24L,NI,-,- F6099 SA9.19-4 JC72-01106A PMO-FRAME FEED;CLP-500,ABS+GF20%,GP2200, F6171 SA9.19-5 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.19-6 JC72-01105A PMO-BUSHING FEED MID;CLP-500,POM,WHITE,- F6160 SNA9.19-7 JC70-00376A IPR-BRKT FEED MID;CLP-500,SECC,-,T0.8,-, F6091 SNA9.19-8 6031-000021 WASHER-PLAIN;-,ID6.0,OD16.0,T0.5,BLK,POL W0031 SNA9.19-9 JC72-01113A PMO-ROLLER FEED MID;CLP-500,POM/GF25%+UR F6193 SA9.19-10 JC66-00618A SHAFT-FEED MID;CLP-500,SUM24L,L37,¥Õ6.0,S S0078 NA9.19-11 JC72-41364A PMO-BUSHING_P/U,MP;ML-6100,POM,BLACK,-,C K3855 SA9.19-12 JC63-00182A GROUND-PICKUP PLATE;CLP-500,SUS304-3/4H, P2061 SNA9.19-13 JC72-00727A PMO-ROLLER FEED;SCX-5100,POM+URETAN,BLAC F6195 SA9.19-14 JC66-00617A SHAFT-FEED;CLP-500,SUM24L,L67.1,¥Õ6.0,-, F6210 SA9.19-15 JC66-00346A GEAR-MP/DUP DRV;SCX-5100,POM,SW-01,M0.8, G0340 SA9.19-16 JC72-01110A PMO-PULLEY FEED L;CLP-500,POM,WHITE,Z=61 F6185 SA9.19-17 6602-001176 BELT-TIMING GEAR;30S2M250,-,T1.36,-,L250 B0055 SA9.19-18 JC66-00332A GEAR-FEED;SCX-5100,POM,M9044,M0.8,Z62/54 F6078 SA9.19-19 JC72-01111A PMO-PULLEY FEED S;CLP-500,POM,WHITE,Z=32 F6186 SA9.19-20 JC72-01134A PMO-BRKT FEED;CLP-500,PC/ABS+SUS430 1.5T F6159 SA9.19-21 JC72-01112A PMO-PULLEY IDLE;CLP-500,POM,WHITE,PI=10, P7026 SA9.19-22 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA9.19-23 6107-001210 SPRING-TS;SUS304-WPB,-,PI0.9,D6.3,-,-,-, S0080 SNA9.19-24 6107-001211 SPRING-TS;SUS304-WPB,-,PI0.75,D6.25,-,-, S0081 SNA9.19-25 JC61-00481A SPRING ETC-FEED MP;SCX-5100,SUS304-WPB,P F6218 SA
9.20-0 JC96-02797A ELA UNIT-GUIDE PAPER T2;CLP-500,SEC,EXPO K3128 SA9.20-1 JC72-01139A PMO-COVER FEED SENSOR;CLP-500,PC,BLACK,- F6165 SA9.20-2 JC92-01455A PBA SUB-FEED SENSOR;CLP-500,SEC,-,FEED S F6152 SA9.20-3 JC72-01135A PMO-ACTUATOR FEED SENSOR;CLP-500,PC,BLAC F6157 SA9.20-4 JC70-00389A IPR-BRKT PAPER GUIDE;CLP-500,SECC,-,T1.2 G2106 SNA9.20-5 JC63-00235A SHEET-PAPER GUIDE;CLP-500,PC,T=0.3,W31.6 S0085 SA9.20-6 JC72-01160A PMO-GUIDE PAPER PATH;CLP-500,HIPS,BLACK, K3910 SA
9.19 Feeder Ass'y
9.20 Guide Paper T2 Ass'y
11
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
9.20-7 JC61-00050A SPRING ETC-ACTUATOR;ML-6060A,SUS304-WPB, Z4132 SA
9.21-0 JC96-03216A ELA UNIT-ITB CAM;CLP-510,SEC,EXPORT,ITB I2131 SA9.21-1 JC72-01154A PMO-DUMMY ITB CAM LOWER;CLP-500,HIPS,BLA D2090 SNA9.2-12 JC96-03242A ELA UNIT-OPE PANEL;CLP-510,SEC,EXPORT,-, Z2649 SA9.21-2 JC92-01651A PBA SUB-PTL_THER;CLP-510,SEC,KOREA,PTL_T P2135 SA9.21-3 JC72-01187A PMO-PTL PATH;CLP-500,PC,TRP,-,KC7133R,-, K4055 SA9.21-4 JC66-00548A SHAFT-ITB CLEAN CAM;CLP-500,SUM24L,L160. S4110 SA9.21-5 JC66-00511A CAM-ITB CLEANING;CLP-500,POM,-,-,BLACK,L K2893 SNA9.21-6 JC61-00699A BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0 K2874 SA9.21-7 6044-000125 RING-E;ID4,OD9,T0.6,PASS,STSC T2001 SA9.21-8 JC72-01155A PMO-DUMMY ITB CAM UPPER;CLP-500,HIPS,BLA D2091 SNA9.21-9 JC39-00381A CBF HARNESS-ITB D_SET;CLP-510,WIRE HARNE C3122 SA9.21-10 JC72-01136A PMO-COVER CAM SHAFT;CLP-500,HIPS,BLACK,- S4071 SNA9.21-11 JC61-00717A GUIDE-PTL SPRING;CLP-500,POM,-,-,-,BLACK G2092 SNA9.21-12 6107-001203 SPRING-ES;SUS304-WPB,-,PI0.5,D4.5,L17.2, S0088 SNA9.21-13 6044-000001 RING-CS;ID3,OD3,T0.25,BLACK,SUS304 D4088 SNA
9.22-0 JC96-02795A ELA UNIT-DUMMY FUSER BASE;CLP-500,SEC,EX D2014 SA9.22-1 JC72-01142A PMO-DUMMY FUSER BASE;CLP-500,PBT+GF30%,B D2087 SA9.22-2 JC72-01140A PMO-COVER FUSER AC;CLP-500,PBT+GF30%,BLA Z2607 SA9.22-3 JC70-10961A IPR-TERMINAL FU;ML-165,C5210P,-,T0.3,-,- K3422 SA9.22-4 JC39-00288A CBF HARNESS-SMPS_AC WIRE;CLP-500,WIRE HA H1250 SA
0105-000101 PAPER-ART;75G,W216,-,WHITE,XEROX 3R2047, SNA0105-001032 PAPER-ART;-,W210,-,WHITE,HANSOL,L297 SNA0201-001162 ADHESIVE-CYA;LOCTITE403,NTR,1250,20G SNA0201-001183 ADHESIVE-AA;ARON ALPHA #202F,NTR,100,20G SNA0202-000008 SOLDER-WIRE;HI-FLO,3.0,-,D3.0,63SN/37PB, SNA0202-000108 SOLDER-CREAM;RMA-20-21L,-,20~38 §-,62.8SS SNA0202-000137 SOLDER-WIRE FLUX;KR-19 RMA SF,-,D0.7,60S SNA0202-001025 FLUX;KS-611,-,-,-,SPRAY SNA0203-000007 TAPE-FILAMENT;3M,T0.15,W18,L55M,TRP SNA0203-001102 TAPE-OPP MASKING;OPP-2,T0.05,W100,L400M, SNA0203-001189 TAPE-ACETATE;#810,T0.05,W12,L65000,NTR SNA0203-001235 TAPE-PAPER;YW-692,T0.15,W5.8,L4000M,- SNA0203-001236 TAPE-PAPER;YW-4620,T0.12,W6.2,L4000M,- SNA0204-000469 THINNER;#4662,-,0.795,- SNA0205-001007 GREASE-BEARING;NYOGEL 759G,HYDROCARBON B SNA0205-001056 GREASE-GRAPHITE;CRS841,WHT,- SNA0205-001059 GREASE-BEARING;PETAMO GHV 133,BEIGE,15KG SNA0205-001067 GREASE-GRAPHITE;NYOGEL 756G,HYDRO CARBON SNA0205-001080 GREASE-BEARING;NYOGEL 774H,NOISE DAMPING SNA0205-001144 GREASE-BEARING;SF-112,HANARL,NOISE TAMPI SNA0401-000005 DIODE-SWITCHING;1N4148,75V,150MA,DO-35,T SA0401-000116 DIODE-SWITCHING;MMSD914T1,100V,200MA,SOD SNA0402-000129 DIODE-RECTIFIER;1N4003,200V,1A,DO-41,TP SA0402-001189 DIODE-RECTIFIER;M4,400V,1A,TS-1,TP SNA0403-000471 DIODE-ZENER;1N5271B,100V,5%,500mW,DO-35, SNA0403-000525 DIODE-ZENER;1N4733A,5%,1000MW,DO-41,TP SA0403-001507 DIODE-ZENER;ZT10-300B,5%,1000MW,DO-41,BK SA0404-000112 DIODE-SCHOTTKY;RB420D,40V,100MA,SOT-23,T SA0407-000101 DIODE-ARRAY;DA204K,20V,100mA,C2-3,SOT-23 SA0501-000010 TR-SMALL SIGNAL;KSC1008,NPN,800mW,TO-92, SA0501-000279 TR-SMALL SIGNAL;KSA1182-Y,PNP,150mW,SOT- SA
9.22 Dummy Fuser Base Ass'y
9.21 ITB Cam Unit
12
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
0501-000294 TR-SMALL SIGNAL;KSA708-Y,PNP,800mW,TO-92 SA0501-000457 TR-SMALL SIGNAL;MMBT2222A,NPN,350MW,SOT- SA0502-000245 TR-POWER;KSB1151-Y,PNP,1.3W,TO-126,-,16 SA0502-001048 TR-POWER;KSD1691,NPN,1.3W,TO-126,BK,160 SA0601-000353 LED;ROUND,RED/Y-GRN,5mm,630/570nm SA0601-001138 LED-IR;ROUND,5mm,150mW,4V,950nm,BK SNA0601-001383 LED;ROUND,RED,3.0MM,700NM SNA0601-001444 LED;SMD,GRN,1MM,560NM,3X1.5X1.4MM SNA0603-001021 PHOTO TR;NPN,20V,5V,20mA,75mW,TP SA0604-001154 PHOTO-INTERRUPTER;TR,0.2-1.0MA,80MW,DIP, SA0604-001257 PHOTO-INTERRUPTER;TR,-,-,DIP-4,BK SNA0803-001097 IC-TTL;7407,BUFFER/DRIVER,DIP,14,300MIL, SA0803-001393 IC-TTL;7407,BUFFER/DRIVER,SOP,14,150MIL, SA0803-003263 IC-CMOS LOGIC;74LCX07,HEX BUFFER,SOIC,14 SA0803-003264 IC-CMOS LOGIC;74LCX06,HEX INVERTER/BUFFE SNA0904-001752 IC-USC;NET2270,16BIT,TQFP,64P,10X10MM,30 SNA1001-000170 IC-ANALOG SWITCH;MC14051BD,SPDT CMOS,SOP SA1006-001250 IC-LINE DRIVER;DS90LV017A,SOIC,8P,150MIL SA1103-001183 IC-EEPROM;24C04,512x8,SOP,8P,5x4mm,2.5/5 SA1103-001328 IC-EEPROM;93C86,2KX8/1KX16BIT,DIP,8P,9.2 SA1105-001384 IC-DRAM;K4S561632,4X4MX16BIT,TSOP(II),54 SA1107-001287 IC-FLASH MEMORY;29LV400,512x8/256x16,TSO SNA1202-000164 IC-VOLTAGE COMP.;393,SOP,8P,150MIL,DUAL, SA1203-002220 IC-POSI.ADJUST REG.;LD1117,DPAK,3P,240MI SA1203-002233 IC-RESET;XC61F,SOT-23,3P,-,PLASTIC,0.7/1 SNA1205-002339 IC-CLOCK GENERATOR;CY25811SC,SOIC,8P,150 SA1404-001141 THERMISTOR-NTC;5.6Kohm,5%,3200K,2.1mW/C, SNA2001-000008 R-CARBON;15KOHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000047 R-CARBON;2.2KOHM,5%,1/4W,AA,TP,2.4X6.4MM SA2001-000058 R-CARBON;5.6Kohm,5%,1/4W,AA,TP,2.4x6.4mm SNA2001-000111 R-CARBON;150OHM,5%,1/4W,AA,TP,2.4X6.4MM SA2001-000281 R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000290 R-CARBON;10KOHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000429 R-CARBON;1KOHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000577 R-CARBON;2KOHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000621 R-CARBON;300KOHM,5%,1/4W,AA,TP,2.4X6.4MM SNA2001-000812 R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2MM SA2001-000935 R-CARBON;68OHM,5%,1/4W,AA,TP,2.4X6.4MM SA2003-000557 R-METAL OXIDE(S);2.2ohm,5%,3W,AA,TP,6x16 SA2003-000631 R-METAL OXIDE(S);3.3ohm,5%,3W,AA,TP,6x16 SA2005-001058 R-WIRE WOUND;0.39ohm,1%,1W,AA,TP,4.3x12m SNA2007-000033 R-CHIP;0ohm,5%,1/4W,TP,3216 SA2007-000066 R-CHIP;20Kohm,1%,1/10W,TP,1608 SA2007-000070 R-CHIP;0ohm,5%,1/10W,TP,1608 SA2007-000074 R-CHIP;100ohm,5%,1/10W,TP,1608 SA2007-000078 R-CHIP;1Kohm,5%,1/10W,TP,1608 SA2007-000082 R-CHIP;3.3Kohm,5%,1/10W,TP,1608 SA2007-000084 R-CHIP;4.7Kohm,5%,1/10W,TP,1608 SA2007-000086 R-CHIP;5.6Kohm,5%,1/10W,TP,1608 SA2007-000090 R-CHIP;10Kohm,5%,1/10W,TP,1608 SA2007-000092 R-CHIP;15Kohm,5%,1/10W,TP,1608 SA2007-000097 R-CHIP;47Kohm,5%,1/10W,TP,1608 SA2007-000102 R-CHIP;100Kohm,5%,1/10W,TP,1608 SA2007-000113 R-CHIP;33ohm,5%,1/10W,TP,1608 SA2007-000116 R-CHIP;120ohm,5%,1/10W,TP,1608 SA2007-000118 R-CHIP;390ohm,5%,1/10W,TP,1608 SA
13
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
2007-000122 R-CHIP;1.2Kohm,5%,1/10W,TP,1608 SA2007-000123 R-CHIP;1.5Kohm,5%,1/10W,TP,1608 SA2007-000134 R-CHIP;33Kohm,5%,1/10W,TP,1608 SA2007-000309 R-CHIP;10ohm,5%,1/10W,TP,1608 SA2007-000539 R-CHIP;200ohm,5%,1/10W,TP,1608 SA2007-000608 R-CHIP;240ohm,5%,1/10W,TP,1608 SA2007-000729 R-CHIP;300ohm,5%,1/10W,TP,1608 SA2007-000736 R-CHIP;30Kohm,1%,1/10W,TP,1608 SNA2007-000839 R-CHIP;39ohm,5%,1/10W,TP,1608 SA2007-000842 R-CHIP;3Kohm,1%,1/10W,TP,1608 SA2007-000939 R-CHIP;47Kohm,1%,1/10W,TP,1608 SNA2007-000965 R-CHIP;5.1Kohm,5%,1/10W,TP,1608 SA2007-001002 R-CHIP;510ohm,5%,1/10W,TP,1608 SA2007-001044 R-CHIP;56ohm,5%,1/10W,TP,1608 SNA2007-001134 R-CHIP;68ohm,5%,1/10W,TP,1608 SA2007-007004 R-CHIP;12Kohm,1%,1/10W,TP,1608 SA2007-007445 R-CHIP;9.09Kohm,1%,1/10W,TP,1608 SNA2007-007726 R-CHIP;35.7ohm,1%,1/10W,TP,1608 SA2007-008567 R-CHIP;15.4KOHM,1%,1/10W,TP,1608 SNA2008-000166 R-FUSIBLE;56ohm,5%,1/4W,AA,TP,2.6x6.7mm SA2009-001085 R-METAL GLAZE;10Mohm,3%,1/2W,CM,BK,18x4m SNA2011-001011 R-NET;10Kohm,5%,1/16W,L,CHIP,8P,TP,3.2x1 SNA2011-001094 R-NET;39OHM,5%,1/16W,L,CHIP,8P,TP SA2201-000017 C-CERAMIC,DISC;1NF,10%,50V,Y5P,TP,5X3.5M SA2201-000119 C-CERAMIC,DISC;100NF,+80-20%,50V,Y5V,TP, SA2201-000138 C-CERAMIC,DISC;0.1NF,10%,50V,Y5P,TP,4X4M SA2203-000041 C-CER,CHIP;0.01NF,0.25PF,50V,C0G,TP,1608 SA2203-000189 C-CER,CHIP;100nF,+80-20%,25V,Y5V,TP,1608 SA2203-000192 C-CER,CHIP;100nF,+80-20%,50V,Y5V,TP,2012 SA2203-000236 C-CER,CHIP;0.1NF,5%,50V,C0G,TP,1608 SA2203-000257 C-CER,CHIP;10nF,10%,50V,X7R,TP,1608 SA2203-000426 C-CER,CHIP;0.018NF,5%,50V,C0G,TP,1608 SA2203-000440 C-CER,CHIP;1nF,10%,50V,X7R,TP,1608,- SA2203-000476 C-CER,CHIP;1000nF,+80-20%,16V,Y5V,-,2012 SA2203-000626 C-CER,CHIP;0.022nF,5%,50V,C0G,TP,1608 SA2203-000783 C-CER,CHIP;0.33NF,5%,50V,C0G,TP,1608 SA2203-000815 C-CER,CHIP;0.033NF,5%,50V,C0G,TP,1608 SA2203-000998 C-CER,CHIP;0.047NF,5%,50V,C0G,TP,1608 SA2203-001598 C-CER,CHIP;2200nF,+80-20%,16V,Y5V,TP,201 SA2203-001656 C-CER,CHIP;0.47nF,5%,50V,NP0,TP,1608 SA2203-001683 C-CER,CHIP;0.068nF,5%,50V,NP0,TP,1608 SA2401-000007 C-AL;470UF,20%,16V,GP,TP,8X11.5MM,3.5 SNA2401-000042 C-AL;100uF,20%,16V,GP,TP,6.3x7,5 SA2401-000207 C-AL;100uF,20%,50V,WT,TP,8x12,5 SNA2401-000414 C-AL;10uF,20%,16V,GP,TP,4x7,5 SNA2401-000802 C-AL;220uF,20%,16V,GP,TP,10x9mm,5mm SNA2401-002300 C-AL;47uF,20%,50V,GP,TP,6.3x11,5 SA2404-000284 C-TA,CHIP;10uF,20%,16V,-,TP,3528 SA2703-000300 INDUCTOR-SMD;1uH,10%,1608 SA2801-003582 CRYSTAL-UNIT;30MHz,50ppm,28-AAA,18pF,80o SA2801-003886 CRYSTAL-UNIT;12MHz,50ppm,28-AAA,16pF,50o SNA2802-001069 RESONATOR-CERAMIC;7.37MHz,0.5%,TP,4.7x4. SNA2804-001613 OSCILLATOR-CLOCK;23.8807363MHZ,50PPM,15P SA2901-001178 FILTER-EMI SMD;25V,2A,-,100000pF,2x1.25x SA3301-000325 BEAD-SMD;60ohm,3.2x2.5x1.3mm,400mA,TP,,, SNA3301-001015 BEAD-AXIAL;70ohm,3.6x0.65x5mm,6000mA,TP, SNA
14
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
3301-001240 BEAD-SMD;120ohm,1.6x0.8x0.8mm,200mA,TP,- SNA3301-001258 BEAD-SMD;600ohm,1608,100mA,,,,1.8ohm SNA3301-001594 BEAD-SMD;90ohm,2.0*1.2*1.3mm,-,TP,-,-,- SA3404-000165 SWITCH-TACT;12V,50mA,160gf,6x6mm,SPST SA3702-001121 CONNECTOR-RIBBON;60P,MALE,STRAIGHT,AUF SA3704-000349 SOCKET-IC;8P,DIP,SN,2.54MM SNA3708-001408 CONNECTOR-FPC/FFC/PIC;12P,1MM,STRAIGHT,S SA3709-001131 CONNECTOR-CARD EDGE;100P,1.27MM,STRAIGHT SNA3711-000164 CONNECTOR-HEADER;1WALL,2P,1R,2.5mm,STRAI SNA3711-000198 CONNECTOR-HEADER;1WALL,3P,1R,2.5mm,STRAI SNA3711-000225 CONNECTOR-HEADER;1WALL,4P,1R,2.5mm,STRAI SNA3711-002000 CONNECTOR-HEADER;BOX,18P,2R,2mm,STRAIGHT SNA3711-002003 CONNECTOR-HEADER;BOX,26P,2R,2mm,STRAIGHT SNA3711-002808 CONNECTOR-HEADER;BOX,7P,1R,2mm,STRAIGHT, SNA3711-002809 CONNECTOR-HEADER;BOX,8P,1R,2mm,STRAIGHT, SA3711-002810 CONNECTOR-HEADER;BOX,9P,1R,2mm,STRAIGHT, SNA3711-002811 CONNECTOR-HEADER;BOX,10P,1R,2mm,STRAIGHT SNA3711-002813 CONNECTOR-HEADER;BOX,12P,1R,2mm,STRAIGHT SA3711-003408 CONNECTOR-HEADER;BOX,2P,1R,2mm,STRAIGHT, SNA3711-003409 CONNECTOR-HEADER;BOX,3P,1R,2mm,STRAIGHT, SNA3711-003410 CONNECTOR-HEADER;BOX,4P,1R,2mm,STRAIGHT, SNA3711-003411 CONNECTOR-HEADER;BOX,5P,1R,2mm,STRAIGHT, SNA3722-001101 JACK-USB;4P/1C,AU,IVR,ANGLE,B TYPE SNA3903-000085 CBF-POWER CORD;DT,US,BP3/YES,I(IEC C13/C K2903 SA6001-000125 SCREW-MACHINE;BH,+,M3,L4,ZPC(YEL),SM20C, SNA6001-000485 SCREW-MACHINE;PH,+,M2.6,L4,ZPC(YEL),SWRC SNA6001-001068 SCREW-MACHINE;PH,+,M2,L16,BLK,SWRCH18A,- SNA6002-000175 SCREW-TAPPING;PWH,+,2,M3,L8,ZPC(YEL),SM2 SNA6002-000308 SCREW-TAPTITE;PH,+,B,M2.6,L6,ZPC(YEL),SW SA6003-000115 SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(BLK),SWRC SA6003-000152 SCREW-TAPTITE;PH,+,B,M2,L10,ZPC(YEL),SWR SA6003-000196 SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRC SA6003-000264 SCREW-TAPTITE;PWH,+,B,M3,L6,ZPC(YEL),SWR SNA6003-000266 SCREW-TAPTITE;PWH,+,S,M3,L6,ZPC(YEL),SWR SNA6003-000267 SCREW-TAPTITE;PWH,+,S,M3,L8,ZPC(YEL),SWR SA6003-000269 SCREW-TAPTITE;BH,+,S,M3,L6,ZPC(YEL),SWRC SA6003-000282 SCREW-TAPTITE;BH,+,B,M3,L8,ZPC(BLK),SWCH SA6003-001001 SCREW-TAPTITE;FH,+,B,M3,L8,ZPC(BLK),SWRC SNA6003-001256 SCREW-TAPTITE;BH,+,B,M4,L10,NI PLT,SWRCH SNA6006-001078 SCREW-TAPTITE;WSP,PH,+,M3,L10,ZPC(YEL),S SNA6006-001193 SCREW-MACHINE;WSP,PH,+,M3,10,ZPC(YEL),SW SNA6009-001396 SCREW-SPECIAL;PH,+,-,M3,L10.3,ZPC(BLK),S SNA6031-000019 WASHER-PLAIN;-,ID6.1,OD8.5,T0.1,BLK,POLY SNA6031-001490 WASHER-PLAIN;POLYMIDE,-,ID7.1,OD14,T0.13 SNA6031-001491 WASHER-PLAIN;POLYMIDE,-,ID8.1,OD12,T0.2, SNA6043-001097 PIN-SPRING;W,D2,L14,-,SUS304 CS 1/2H,T0. SNA6107-001197 SPRING-CS;SUS304-WPB,-,PI0.9,D5.6,L27,-, SNA6107-001204 SPRING-ES;SUS304-WPB,-,PI0.6,D7.5,L22.9, SNA6107-001206 SPRING-TS;SUS304-WPB,BLACK,PI1.5,D10,L5, S0011 SNA6107-001208 SPRING-TS;SWP,RIGHT,PI1.4,D9.2,L6.5,-,-, SNA6107-001212 SPRING-TS;SUS304-WPB,-,PI0.9,D13,L4.7,-, SNA6501-000004 CABLE TIE;DA-80,T1,W2.5,L80,NTR,NYLON66 K2756 SA6601-001227 BEARING-BALL;L-1680HH,ID8,OD16,L5.0,SUS4 SNA6902-000048 BAG PE;LDPE,T0.03,L400,W400,TRP,8,2,PE M SNA6902-000288 BAG PE;LDPE,T0.05,W250,L450,TRP,8,2- SNA6902-000332 BAG CONDUCTIVE;PE+CARBON,T0.1,W250,L500, SNA
15
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
6902-000606 BAG CONDUCTIVE;PE+CARBON,T0.1,W305,L475, SNA6902-000655 BAG PE;HDPE,T0.03,W800,L1300,TRP,28,6M T SNAJB13-00004A IC ASIC-OPE;SF-3100,HT48C5,SSOP,48P,16.1 SAJB68-00072A LABEL(R)-BAR RIBON;SF-3000,PY,80X91000,T SNAJB68-00073A LABEL(R)-BAR CODE;SF-3000,PY,38X6.5,T0.1 SNAJB68-00916A LABEL RATING-BLANK;SF-340,SEC,TETRON,0.0 SNAJB75-10028A MEC-RIBBON BARCODE S;-,-,PW-2,PI1, D4.9, SNAJB75-10029A MEC-RIBBON BARCODE S;COLUMBUS,KISCOM,BLK SNAJC02-00017A TONER-GRINDED BLACK;CLP-500,SA-79EK-B,BL SNAJC02-00018A TONER-GRINDED YELLOW;CLP-500,SA-79EK-Y,Y SNAJC02-00019A TONER-GRINDED MAGENTA;CLP-500,SA-79EK-M, SNAJC02-00020A TONER-GRINDED CYAN;CLP-500,SA-79EK-C,CYA SNAJC13-00014C IC ASIC-SPGPM(3);SPGPM_D,SCX-6320F,256PI SAJC13-00020A IC ASIC-ENGINE CONTROL;LPEC1,CLP-500,128 SAJC33-00011A SOLENOID-DEVE HVPS;-,CLP-500,DC24V,190§Ù S7079 SAJC39-00277A CBF HARNESS-MAIN ERASER;CLP-500,WIRE HAR E3000 SAJC39-00282A CBF HARNESS-MAIN_P.EMPTY;CLP-500,WIRE HA H1144 SAJC39-00284A CBF HARNESS-MAIN_FEED;CLP-500,WIRE HARNE F6045 SAJC39-00285A CBF HARNESS-MAIN-TEMPERATURE;CLP-500,WIR H1158 SAJC39-00286A CBF HARNESS-MAIN_MP.EMPTY;CLP-500,WIRE H H1142 SAJC39-00290A CBF HARNESS-ERASER_BOARD;CLP-500,WIRE HA H1077 SAJC39-00294A CBF HARNESS-MAIN_S/W(5V);CLP-500,WIRE HA H1148 SAJC39-00295A CBF HARNESS-SMPS_COVER S/W;CLP-500,WIRE H1251 SAJC39-00306A CBF HARNESS-LCD;CLP-500,WIRE,UL2877,14-1 SAJC39-00379A CBF HARNESS-EX_WASTE;CLP-510,WIRE HARNES SAJC39-00380A CBF HARNESS-PTL_THER;CLP-510,WIRE HARNES SAJC39-00382A CBF HARNESS-ITB D_ITB;CLP-510,WIRE HARNE SNAJC39-00383A CBF HARNESS-DEVE OEM;CLP-510,WIRE HARNES SAJC39-00385A CBF HARNESS-SUPPLY;CLP-510,WIRE HARNESS, SAJC39-00388A CBF SIGNAL-DEVE DRI;CLP-510,12PIN,FFC,18 SAJC39-40511A CBF HARNESS;ML-80,JUMPER,AWG22,52mm,SILV SAJC41-00133A PCB-SENSOR;SCX-5100,FR-1,1L,V1.0,1.6T,11 SNAJC41-00166A PCB-DEVE BIAS;CLP-500,FR-1,1L,-,1.6,55*2 SNAJC41-00169A PCB-TEMPERATURE;CLP-500,FR-1,1L,-,1.6,22 SNAJC41-00201A PCB-TONER_TX;CLP-500,FR-1,1L,-,1.2,15*10 SNAJC41-00202A PCB-TONER_RX;CLP-500,FR-1,1L,-,1.2,15*10 SNAJC41-00224A PCB SUB-GINKGO_DEVE_CRUM;CLP-500,FR-4,2 SNAJC41-00225A PCB SUB-GINKGO_ITB;CLP-500,FR-4,2L,-,1.6 SNAJC41-00254A PCB MAIN-CONT_BB_PLUS;CLP-510,FR-4,4,-,1 SNAJC41-00255A PCB SUB-OEM_BB_PLUS;CLP-510,FR-1,1L,-,1. SNAJC41-00256A PCB SUB-DRIVER_BB_PLUS;CLP-510,FR-1,1L,- SNAJC41-00257A PCB MAIN-CONT_BB_PLUS;CLP-510,FR-1,1,0.1 SNAJC41-10519A PCB-PTL;ML-165,FR-1,1L,T1.6mm,217.7X9m SNAJC46-00232A S/W APPLICATION-DRV;-,CLP-510,CLP DRV,1. SNAJC61-00011A SPRING ETC-FEED;SF-5100,SUS304WPB,0.6,-, SAJC61-00032A SPRING ETC--HV SMALL;ML-6060A,SUS 304 WP SNAJC61-00035A SPRING ETC-HV APOLLO;SF-5100,SUS304WPB,0 SNAJC61-00549A SPRING ETC-PICKUP,MP;SCX-5312F,SUS304-WP P2165 SAJC61-00714A STOPPER-STACKER F;CLP-500,POM,-,-,-,WHIT Z5098 SAJC61-00715A STOPPER-STACKER R;CLP-500,POM,-,-,-,WHIT Z5099 SAJC61-00753A PLATE-DUMMY Y;CLP-500,SUS304CSP,1/2H,T0. SNAJC61-00754A PLATE-DUMMY BK;CLP-500,SUS304CSP,1/2H,T0 SNAJC61-00772A BUSH-DEV DR;CLP-500,BRONZE,ID7.0,OD9.4,L SNAJC61-00774A BUSH-DEV SR;CLP-500,BRONZE,ID4.0,OD7.0,L SNAJC61-00827A BLADE-SUS BLACK;CLP-500,SUS301-CSP 1/2H, SNAJC61-00828A BLADE-SUS COLOR;CLP-500,SUS301-CSP 1/2H, SNA
16
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
JC61-00839A BLADE-CLEANING;CLP-500,URETHAN,TRP,W15*L SNAJC61-00869A FRAME-M-DRAWER CONNECTOR;CLP-500,PET+GF3 SNAJC61-00977A HOLDER-M-TR REAR;CLP-510,POM,-,-,-,BLACK SNAJC61-00980A HOLDER-M-SHAFT_OPC;CLP-510,POM,5,16,PI 1 SNAJC61-00981A GUIDE-M-BRACKET_C;CLP-510,ABS,4,4.4,239. SNAJC61-00982A BRACKET-P-SEAL_C;CLP-510,SECC,0.8,239.6, SNAJC61-00983A BUSH-TR;CLP-510,BRONZE+ST,ID6.0,OD10.0,L SNAJC61-00985A BRACKET-P-SEAL_BK;CLP-510,SECC,0.8,239.6 SNAJC61-00986A GUIDE-M-BRACKET_BK;CLP-510,ABS,4,6,239.6 SNAJC61-00989A STOPPER-M-ITB SPACER F/R;CLP-510,ABS,V0, SNAJC61-00989B STOPPER-M_REAR;CLP-510,ABS,V0,T3.0,-,-,G SNAJC62-00091A SEAL-MANUAL SHEET;CLP-500,PE FOAM,-,T=10 SNAJC62-00092A SEAL-SIDE BLADE DEVE;CLP-500,PE FOAM,-,T SNAJC62-00093A SEAL-BLADE INNER;CLP-500,SM55 FOAM,-,T=2 SNAJC62-00094A SEAL-BLADE UPPER;CLP-500,URETHANE FOAM,- SNAJC62-00096A SEAL-DUST PROOF LSU;CLP-500,PET FILM,-,T SNAJC62-00097A SEAL-COVER WASTE TANK;CLP-500,URETHAN FO SNAJC62-00098A SEAL-GUIDE ERASER LAMP;CLP-500,NITTO #50 SNAJC62-00099A SEAL-SHUTTER;CLP-500,URETHAN FOAM,-,T=2. SNAJC62-00100A SEAL-SIDE BLADE;CLP-500,URETHAN FOAM,-,T SNAJC62-00101A SEAL-U_COVER WASTE TANK;CLP-500,URETHAN SNAJC62-00102A SEAL-URETHAN FILM;CLP-500,URETHAN FILM,- SNAJC62-00103A SEAL-TEFLON FELT FRONT;CLP-500,TEFLON FE SNAJC62-00104A SEAL-TEFLON FELT REAR;CLP-500,TEFLON FEL SNAJC62-00105A SEAL-CLEANING BLADE;CLP-500,URETHANE FOA SNAJC62-00106A SEAL-SHUTTER 2;CLP-500,URETHAN FOAM,-,T4 SNAJC62-00107A SEAL-COLLAR PORON;CLP-500,PORON,-,T2.0, SNAJC62-00108A SEAL-BRACKET SIDE;CLP-500,URETHANE FOAM, SNAJC62-00115A SEAL-BRACKET UPPER;CLP-500,EPDM,-,T2.5,W SNAJC62-00116A SEAL-DUMMY HOLE UPPER;CLP-500,PE FOAM,-, SNAJC62-00117A SEAL-DUMMY COVER;CLP-500,PPMB,-,T1.0,W22 SNAJC62-00118A SEAL-FELT BLACK F;CLP-500,TEFLON FELT,-, SNAJC62-00122A SEAL-SIDE BLOCK;CLP-500,PE FOAM,-,T3.5,W SNAJC62-00123A SEAL-SIDE SR F;CLP-500,PORON ,-,T5.0,W5, SNAJC62-00124A SEAL-SUPPLY COLOR F;CLP-500,PORON LE20,- SNAJC62-00125A SEAL-SUPPLY COLOR R;CLP-500,PORON LE20,- SNAJC62-00126A SEAL-SUPPLY BLACK F;CLP-500,PORON LE20,- SNAJC62-00127A SEAL-SUPPLY BLACK R;CLP-500,PORON LE20,- SNAJC62-00128A SEAL-SIDE DUMMY COVER;CLP-500,PE FOAM,-, SNAJC62-00131A SEAL-BRACKET INNER_BK;CLP-500,PE FOAM,GR SNAJC62-00132A SEAL-UPPER COVER;CLP-500,URETHANE FORM,G SNAJC62-00133A SEAL-BLADE INNER_BK;CLP-500,EPDM,GRAY,T2 SNAJC62-00140A SEAL-BLADE SIDE_BK;CLP-500,PE FORM,GRAY, SNAJC62-00144A SEAL-AGITATOR_C;CLP-500,PORON(LE-20),-,5 SNAJC63-00179A COVER-FRONT HINGE F;CLP-500,POM,-,-,-,-, H3009 SAJC63-00205A COVER-M-DUMMY BLACK;CLP-500,ABS,-,-,-,HB SNAJC63-00206A COVER-M-DUMMY CYAN;CLP-500,ABS,-,-,-,HB, SNAJC63-00228A SHEET-AGITATOR A;CLP-500,PET,T=0.1,W16.5 SNAJC63-00229A SHEET-AGITATOR B;CLP-500,PET,T=0.1,W16.5 SNAJC63-00230A SHEET-COVER DUMMY;CLP-500,TETRON,T=0.1,W SNAJC63-00231A SHEET-DEVE FRAME;CLP-500,PET,T=0.125,W27 SNAJC63-00232A SHEET-ITB WASTE;CLP-500,PE FILM,T=0.2,W1 SNAJC63-00233A SHEET-ITB BUFFER;CLP-500,PE FILM,T=0.3,W SNAJC63-00237A SHEET-ITB MAIN;CLP-500,URETHAN FILM,T=0. SNAJC63-00238A SHEET-ITB LOW;CLP-500,PE FILM,T=0.2,W21, SNAJC63-00239A SHEET-ITB TRC;CLP-500,PE FILM,T=0.2,W24. SNA
17
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
JC63-00241A SHEET-ITB BLADE;CLP-500,PE SHEET,T=0.2,W SNAJC63-00248A SHEET-HV HARNESS;CLP-500,PC,T0.5,W33.5,L H1336 SAJC63-00278A SHEET-REAR BLACK;CLP-500,PET FILM,T0.054 SNAJC63-00279A SHEET-REAR COLOR;CLP-500,PET FILM,T0.054 SNAJC63-00280A SHEET-RECYCLE BLACK;CLP-500,PET FILM,T0. SNAJC63-00281A SHEET-RECYCLE COLOR;CLP-500,PP FILM,T0.1 SNAJC63-00282A SHEET-SUPPLY COLOR;CLP-500,URETHANE SHEE SNAJC63-00283A SHEET-TONER RECYCLE;CLP-500,PET FILM,T0. SNAJC63-00284A SHEET-SUPPLY BLACK;CLP-500,PET,T0.2,W217 SNAJC63-00427A SHEET-DEVE FRAME_C;CLP-500,PET,0.125,17, SNAJC63-00552A SHEET-COVER HOLE;CLP-510,PET FILM,T=0.1, SNAJC63-00570A SHEET-AGITATOR_D;CLP-510,PET,0.2,11.8,4. SNAJC66-00486A GEAR-OPC AUGER;CLP-500,POM,M0.8,Z19,-,-, SNAJC66-00487A GEAR-OPC DRUM;CLP-500,PC,LF1025,M0.6,Z12 SNAJC66-00490A GEAR-OPC IDLE_Z35;CLP-500,POM,M0.6,Z35,- SNAJC66-00491A GEAR-OPC IDLE_Z42/Z28;CLP-500,POM,M0.6/M SNAJC66-00492A GEAR-OPC IDLE_Z21;CLP-500,POM,M0.8,Z21,- SNAJC66-00493A GEAR-OPC IDLE_Z32;CLP-500,POM,M0.8,Z32,- SNAJC66-00494A GEAR-OPC ROLL CLEAN_Z18;CLP-500,POM,M0.8 SNAJC66-00495A GEAR-DEVE Z18/Z18;CLP-500,POM,M0.8/M0.6, SNAJC66-00496A GEAR-DEVE FRONT_Z18;CLP-500,POM,M0.6,Z18 SNAJC66-00497A GEAR-DEVE IDEL_Z21;CLP-500,POM,M0.6,Z21, SNAJC66-00498A GEAR-DEVE IDEL_Z24;CLP-500,POM,M0.6,Z24, SNAJC66-00499A GEAR-DEVE IDEL A_Z30/Z19;CLP-500,POM,M0. SNAJC66-00501A GEAR-DEVE IDEL_Z43/Z19;CLP-500,POM,M0.6, SNAJC66-00502A GEAR-DEVE IDEL_Z16;CLP-500,POM,M0.6,Z16, SNAJC66-00503A GEAR-DEVE IDEL_Z23;CLP-500,POM,M0.6,Z23, SNAJC66-00504A GEAR-DEVE RECY_Z16;CLP-500,POM,M0.6,Z16, SNAJC66-00505A GEAR-ITB AUGER_Z28;CLP-500,POM,M0.5,Z28, SNAJC66-00506A GEAR-ITB CLEAN_Z57;CLP-500,POM,M0.5,Z57, SNAJC66-00507A GEAR-ITB DRIVE_Z60;CLP-500,POM,M0.5,Z60, SNAJC66-00508A GEAR-ITB IDLE 1_Z28;CLP-500,POM,M0.5,Z28 SNAJC66-00509A GEAR-ITB IDLE 2_Z28;CLP-500,POM,M0.5,Z28 SNAJC66-00514A GEAR-TRANSFER_Z23;CLP-500,POM,M0.8,Z23,- SAJC66-00521A GEAR-DEVE IDLE_Z18;CLP-500,POM,M0.6,Z18, SNAJC66-00542A ROLLER-ITB DRIVE;CLP-500,AL6063+EDPM,D29 SNAJC66-00603C DRUM-OPC RICOH;CLP-500,AL,-,OD120,L266,- SNAJC66-00604A ROLLER-CHARGER CLEANING;CLP-500,URETHAN+ SNAJC66-00605A ROLLER-DEV;CLP-500,NBR+ECO,¥Õ14.0,L228.8S NAJC66-00606A ROLLER-DEV SUPPLY;CLP-500,SILICON FOAM, SNAJC66-00609B ROLLER-ITB CLEAN BU;CLP-510,AL+SUM24L,¥ÕS NAJC66-00610A ROLLER-ITB T1;CLP-500,SUM22L,¥Õ12.0,L280S NAJC66-00611B ROLLER-ITB TENSION;CLP-510,AL+SUM24L,¥Õ1S NAJC66-00613A ROLLER-TRANSFER;CLP-500,EDPM+SUM24L,¥Õ24S NAJC66-00620A SHAFT-OPC DRUM;CLP-500,SUS416F,L310,¥Õ10S NAJC66-00621A DRUM-ITB BELT;CLP-500,PC+ALLOY,¥Õ120,-,WS NAJC66-00933A ROLLER-M-ITB BELT DF;CLP-510,POM,29.6,L1 SNAJC68-00274A LABEL(R)-RIBBON;SF-5100,100,-,-,BLK SNAJC68-00320A MANUAL-(CARD)SEM SVC CARD;ML-5100A,SEM,X SNAJC68-00573A LABEL(R)-BARCODE;ML-4500,PET,T0.05,10mm, SNAJC68-01134A LABEL(P)-BLANK(FUSER);ML-1710D3,-,WHITE SNAJC68-01154A LABEL(R)-POP(A);CLP-500,-,PC+HOLOGRAM,T0 SNAJC68-01156A MANUAL-SHEET DEVE;CLP-500,-,ENGLISH,-,AR SNAJC68-01175A LABEL(P)-FRONT INNER;CLP-500,-,YUPO PAPE L0004 SNAJC68-01181A LABEL(P)-TOP;CLP-500,-,YUPO PAPER,100G,W L0005 SNAJC68-01226A LABEL(R)-COLOR BLACK;CLP-500,-,FASCAL400 SNA
18
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
JC68-01228A LABEL(P)-OPC NOTICE;CLP-500,-,YOPO PAPER SNAJC68-01229A LABEL(R)-COLOR YELLOW;CLP-500,-,FASCAL40 SNAJC68-01230A LABEL(R)-COLOR CYAN;CLP-500,-,FASCAL400P SNAJC68-01231A LABEL(R)-COLOR MAGENTA;CLP-500,-,FASCAL4 SNAJC68-01428A MANUAL-QIG;CLP-510,SEE,16 LANGUAGE,GERMA SNAJC68-01483A MANUAL-SHEET ITB;CLP-510,SEC,ENGLISH,-,A SNAJC68-01484A MANUAL-QRG;CLP-510,XEROX,EN+FR+IT+GE+SP+ SNAJC68-01488A MANUAL-DOC POCKET;CLP-510,SEC,ENGLISH,U. SNAJC68-10914D LABEL(P)-SERIAL NO;ML-85,ART,70X15,G100, SNAJC68-10914E LABEL SERIAL-YELLOW;CLP-510,SEC,ART,0.1, SNAJC68-10914F LABEL SERIAL-CYAN;CLP-510,SEC,ART,0.1,70 SNAJC68-10914G LABEL SERIAL-MAGENTA;CLP-510,SEC,ART,0.1 SNAJC68-10932A LABEL(P)-BLANK(ML);ML-85/85G,ART,70X60,G SNAJC68-30928E LABEL(P)-CAUTION, HOT_FU;ML-1430,-,PET,T L0020 SNAJC69-00640A CUSHION-SET MAIN;CLP-510,EPS,-,W611,L565 SNAJC69-00644A BOX(P)-MAIN BBP;CLP-500,DW,A-1,596,550,5 SNAJC69-00732A BOX(P)-PAD TOP;CLP-510,DW,-,-,615,545,-, SNAJC70-00050A IPR-TERMINAL;SF-5100,SWRCH1018,-,4.4,-,- SNAJC70-00281A IPR-BRKT CLEANING;ML-1650,SECC,-,250X18. SNAJC70-00345A IPR-BRKT SOLENOID;CLP-500,SECC,-,T1.2,-, S8010 SNAJC70-00347A IPR-CONTCAT DRUM(GND);CLP-500,C5201 1/2H SNAJC70-00348A IPR-CONTCAT ROLL CHARGER;CLP-500,SUS301- SNAJC70-00349A IPR-CONTCAT SOKET OEM;CLP-500,C5210 1/2H SNAJC70-00350A IPR-OPC SPRING HANDLE;CLP-500,SUS301-CSP SNAJC70-00351A IPR-ITB BRKT DRAW CONN.;CLP-500,SECC,-,T SNAJC70-00352A IPR-ITB PLATE SPRING HV;CLP-500,SUS304 C SNAJC70-00354A IPR-ITB WASHER SPRING;CLP-500,SUS304 CSP SNAJC70-00391A IPR-DEV BRKT DOCTOR;CLP-500,SECC,-,T1.2, SNAJC70-00392A IPR-DEV BRKT DOCTOR BK;CLP-500,SECC,-,T1 SNAJC70-00395A IPR-DEV PLATE BIAS;CLP-500,C5210,-,T0.3, SNAJC70-00396A IPR-DEV PLATE FUSERBLE;CLP-500,C5201,-,T SNAJC70-00398A IPR-DEV PLATE BIAS DR BK;CLP-500,SUS304- SNAJC70-00399A IPR-DEV PLATE BIAS DR C;CLP-500,SUS304-C SNAJC70-00402A IPR-DEV PLATE BIAS SR;CLP-500,SUS304-CSP SNAJC70-00403A IPR-DEV PLATE BIAS SR BK;CLP-500,SUS304- SNAJC70-00434A IPR-PLATE CONTACT HVPS;CLP-500,C5210P,-, S7033 SNAJC70-00435A IPR-PLATE SPRING HVPS;CLP-500,BECU,-,T0. S7034 SNAJC72-00463A PMO-CAP CONNECTOR L;ML-6060A,POM,BLACK,- Z0013 SAJC72-00465A PMO-CAP CONNECTOR U;ML-6060A,POM,BLACK,- Z0014 SAJC72-01013A PMO-AUGER WASTE TONER;CLP-500,PC+GF20%,B SNAJC72-01014A PMO-BRKT FRAME FRONT;CLP-500,ABS+GF20%,B SNAJC72-01015A PMO-BRKT FRAME REAR;CLP-500,ABS+GF20%,IC SNAJC72-01016A PMO-COVER ROLL CHARGER;CLP-500,ABS,BLACK SNAJC72-01017A PMO-COVER WASTE TANK;CLP-500,ABS,BLACK,- SNAJC72-01018A PMO-OPC FLANGE DRUM;CLP-500,POM,WHITE,-, SNAJC72-01019A PMO-OPC FRAME BASE;CLP-500,ABS+GF20%,BLA SNAJC72-01020A PMO-GUIDE ERASER LAMP;CLP-500,ACRYL,TRP SNAJC72-01021A PMO-OPC HANDLE;CLP-500,ABS+GF20%,ICE GRE SNAJC72-01022A PMO-HOLDER CR FRONT;CLP-500,POM,BLACK,-, SNAJC72-01023A PMO-HOLDER CR REAR;CLP-500,POM,BLACK,-,D SNAJC72-01024A PMO-PUSH LOCKING;CLP-500,POM,BLACK,-,DEL SNAJC72-01025A PMO-SHUTTER WASTE TANK;CLP-500,ABS,BLACK SNAJC72-01026A PMO-OPC SOKET OEM;CLP-500,ABS,BLACK,-,HB SNAJC72-01027A PMO-ITB AUGER CLEAN;CLP-500,ABS+GF20%,BL SNAJC72-01029A PMO-ITB BUSH DRIVE F;CLP-500,POM,BLACK,- SNAJC72-01030A PMO-ITB BUSH DRIVE FIX;CLP-500,POM,BLACK SNA
19
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
JC72-01031A PMO-ITB BUSH GUIDE CF;CLP-500,POM,WHITE, SNAJC72-01032A PMO-ITB BUSH GUIDE CR;CLP-500,POM,WHITE, SNAJC72-01034A PMO-ITB BUSH GUIDE DR;CLP-500,POM,BLACK, SNAJC72-01035A PMO-ITB BUSH NIP R;CLP-500,POM,BLACK,-,M SNAJC72-01036A PMO-ITB BUSH T1;CLP-500,POM,BLACK,-,DE85 SNAJC72-01037A PMO-ITB BUSH TENSION;CLP-500,POM,BLACK,- SNAJC72-01038A PMO-ITB COVER LOWER;CLP-500,ABS+GF20%,BL SNAJC72-01039A PMO-ITB COVER MAIN;CLP-500,ABS+GF20%,BLA SNAJC72-01040A PMO-ITB COVER UNIT F;CLP-500,ABS,BLACK,- SNAJC72-01041A PMO-ITB COVER UNIT R;CLP-500,ABS,BLACK,- SNAJC72-01042A PMO-ITB GAP RING;CLP-500,POM,BROWN,-,500 SNAJC72-01043A PMO-ITB GUIDE AUGER;CLP-500,PC/ABS,BLACK SNAJC72-01044A PMO-ITB G/BELT TENSION;CLP-500,POM,BLACK SNAJC72-01045A PMO-ITB HANDLE FIX;CLP-500,POM,BLACK,-,M SNAJC72-01046A PMO-ITB HANDLE UNIT;CLP-500,ABS,ICE GREE SNAJC72-01047A PMO-ITB HINGE BRKT BLADE;CLP-500,POM,BLA SNAJC72-01048A PMO-ITB HOLDER TOF;CLP-500,ABS,BLACK,-,H SNAJC72-01051A PMO-ITB LEVER BLADE;CLP-500,POM,BLACK,-, SNAJC72-01052A PMO-ITB POSITION UNIT F;CLP-500,PC/ABS,P SNAJC72-01053A PMO-ITB POSITION UNIT R;CLP-500,PC/ABS,I SNAJC72-01054A PMO-ITB SHUTTER AUGER;CLP-500,PC/ABS,BLA SNAJC72-01088A PMO-HOOK TR FRONT;CLP-500,POM,PUPPLE,-,M SNAJC72-01095A PMO-GAP RING;CLP-500,POM,BLACK,PI23.66,T SNAJC72-01114A PMO-DEV BUSH SLIDE;CLP-500,POM,BLACK,-,M SNAJC72-01119A PMO-DEV COVER BLACK;CLP-500,HIPS,BLACK,- SNAJC72-01120A PMO-DEV COVER CYAN;CLP-500,HIPS,BLACK,-, SNAJC72-01121A PMO-DEV COVER MAGENTA;CLP-500,HIPS,BLACK SNAJC72-01122A PMO-DEV COVER YELLOW;CLP-500,HIPS,BLACK, SNAJC72-01123A PMO-DEV FRAME;CLP-500,ABS+PC20%,BLACK,-, SNAJC72-01124A PMO-DEV FRAME BK;CLP-500,ABS+PC20%,BLACK SNAJC72-01125A PMO-DEV GAP RING;CLP-500,POM,WHITE,PI14. SNAJC72-01126A PMO-DEV GUIDE SUPPLY;CLP-500,PC+GF20%,BL SNAJC72-01127A PMO-DEV GUIDE SUPPLY BK;MLC-500,PC+GF20% SNAJC72-01128A PMO-DEV HOUSING BIAS;CLP-500,ABS,BLACK,- SNAJC72-01129A PMO-DEV HOUSING FUSERBLE;CLP-500,ABS,BLA SNAJC72-01130A PMO-DEV PLATE GEAR;CLP-500,POM,BLACK,-,M SNAJC72-01131A PMO-DEV PLATE GEAR BK;CLP-500,POM,BLACK, SNAJC72-01132A PMO-DEV TONER AGIATOR;CLP-500,PC,BLACK,- SNAJC72-01133A PMO-DEV TONER RECYCLE;CLP-500,PC,BLACK,- SNAJC72-01175A PMO-DEVE OPEN LINK;CLP-500,PC/ABS,BLACK, O1078 SNAJC72-01198B PMO-OPE KEY 1 CAP;CLP-510,ABS,G71312,-,- SNAJC72-01218A PMO-HOLDER ERASER;CLP-500,PP,BLACK,-,-,- E3002 SAJC72-01219A PMO-ITB COVER CLEAN LOW;CLP-500,ABS,BLAC SNAJC72-01234A PMO-DEVE CAP TONER;CLP-500,PP,BLACK,-,H5 SNAJC72-01264A SPONGE-ITB BF;CLP-500,URETHAN SPONGE,-,T SNAJC72-01265A SPONGE-ITB BR;CLP-500,URETHAN SPONGE,-,T SNAJC72-01266A SPONGE-ITB GAP;CLP-500,URETHAN SPONGE,-, SNAJC72-01268A SPONGE-ITB SHEET;CLP-500,URETHAN SPONGE, SNAJC72-01269A SPONGE-ITB SR;CLP-500,URETHAN SPONGE,-,T SNAJC72-01270A SPONGE-ITB TOP_BOTTOM;CLP-500,URETHAN SP SNAJC72-01271A SPONGE-ITB BLADE L;CLP-500,URETHANE SPON SNAJC72-01272A SPONGE-ITB BF R;CLP-500,URETHAN SPONGE,- SNAJC72-01273A SPONGE-ITB BLADE R;CLP-500,URETHAN SPONG SNAJC72-01274A SPONGE-ITB LOWER;CLP-500,URETHAN SPONGE, SNAJC72-01275A SPONGE-ITB SHUTTER;CLP-500,URETHAN SPONG SNAJC72-01276A SPONGE-ITB SIDE;CLP-500,URETHAN SPONGE,- SNA
20
Parts List
Draw# Part Code Description Location SNA
SA : Service Available, SNA : Service not Available
JC72-01277A SPONGE-ITB TOP;CLP-500,URETHAN SPONGE,-, SNAJC73-00090A RPR-RCT PAD PICKUP,MP;SCX-5100,SILICON,T P2146 SAJC73-20902A REX-CLEANING BLADE;ML-6000,URETHANE RUBB SNAJC74-10901A MPR-WASHER SUPPLY;ML-5000,POLY,ID4.1*OD1 SNAJC75-00032C MEC-CHRAGER ROLLER;CLP-510,SEC,NBR+HYDRI T2136 SAJC92-01450A PBA SUB-ERASER;CLP-500,SEC,-,ERASER,LED, E3001 SAJC92-01534B PBA SUB-DEVE_BIAS_YK;CLP-500,SEC,-,DEVE_ SNAJC92-01551A PBA SUB-DEVE_CRUM;CLP-500,SEC,KOREA,DEVE SNAJC92-01551B PBA SUB-DEVE_CRUM_M;CLP-500,SEC,KOREA,DE SNAJC92-01551C PBA SUB-DEVE_CRUM_C;CLP-500,SEC,KOREA,DE SNAJC92-01551D PBA SUB-DEVE_CRUM_K;CLP-500,SEC,KOREA,DE SNAJC92-01569A PBA SUB-GINKGO_ITB;CLP-500,SEC,KOREA,GIN SNAJC92-01632A PBA SUB-DRIVER_BB_PLUS;CLP-510,SEC,KOREA M2011 SAJC96-03213A ELA HOU-MAIN LINE;CLP-510,SEC,EXPORT,-,- SNAJC96-03274A ELA HOU-ITB_DRAW;CLP-510,KOREA,KOREA,ITB SNAJC97-01819A MEA UNIT-SUS BLADE BLACK;CLP-500,-,SECC+ SNAJC97-01820A MEA UNIT-SUS BLADE COLOR;CLP-500,-,SECC+ SNAJC97-01821A MEA UNIT-WASTE TONER TANK;CLP-500,SEC,EX T2130 SAJC97-01828A MEA UNIT-DUPLEX;CLP-500,SEC,EXPORT,-,-,- D0010 SAJC97-01835A MEA UNIT-CLEANING BLADE;CLP-500,OPC,SECC SNAJC97-01836A MEA UNIT-CLEANING BLADE;CLP-500,ITB,SECC SNAJC97-01874A MEA UNIT-OPC FLANGE;CLP-500,SEC,OPC FLAN SNAJC99-01744Q INA-ACCESSORY(XAA);CLP-510/XAA,SAMSUNG,A SNAJC99-01810A PAA MAIN-PACKING;CLP-510,SAMSUNG,EXPORT, SNAJC99-01813A INA-ACCESSORY(XAA);CLP-510/XAA,SAMSUNG,A SNAJC99-01824J PAA-LABEL_XBH;CLP-510/XBH,SAMSUNG,BIGBAN SNAJG07-20001A LCD;SF4000,UC-162937-TNAR5-A,BLK/G L3015 SAJK72-00058A PCT-SILP WASHER;SRP-350,P.A+GRAPHITE,T0. SNA
21
1010
10-1Samsung Electronics
Block Diagram
Service Manual
10. Block Diagram
1111
11-1Samsung Electronics
Connection Diagram
Service Manual
11. Connection Diagram
FU
SE
R
LS
UD
CM
oto
r(W
aste
Ag
itato
r)
So
len
oid
(Dev
e1
st)
So
len
oid
(Dev
e2
nd
)S
ole
no
id(D
eve
3rd
)
So
len
oid
(Dev
e4
th)
Clu
tch
(Dev
e1s
t)
Clu
tch
(Dev
e2n
d)
Clu
tch
(Dev
e3r
d)
Clu
tch
(Dev
e4t
h)
FA
N(F
use
r)
Pan
el
CN
2
US
B
IEE
E12
84
NP
C(O
pti
on)
OP
C
Era
ser
(no
tus
e)
CN
1
PT
L&
Tem
p4
CN
1
SC
F(O
pti
on
)
Sen
sor(
Pap
erE
mp
ty)
Se
nso
r(M
P_
Em
pty
)
Se
nso
r(F
eed
)
Clu
tch(
Fee
d)
So
len
oid
(Pic
ku
p)
So
len
oid
(MP
)
So
len
oid
(Du
ple
x)
ITB
Wa
ste
ton
er&
Ex
it
Se
nso
r(T
em
p3)
BLD
CM
oto
r&
Driv
e(D
EVE
)CN1
BL
DC
Mot
or&
Dri
ve(M
ain
)CN1
Po
we
r(A
CIn
pu
t,22
0/11
0V)
Sw
itch1
(Rig
htco
ver)
Sw
itch2
(Le
ftco
ver)
SMPS
CON4
CON1
CON2
CON3
Sw
itch3
(Le
ftco
ver)
Dev
elo
per
_1s
t
De
velo
pe
r_2
nd
De
velo
pe
r_3
rd
Dev
elo
per
_4th
Dev
eO
EM
KE
YC
N1
CN
2
V1,
2,3
V4,
5,6
V7,
8,9
V1
0,1
1,1
2
HV
PS
CN
1(1,
2)
T1
T2
Ch
arg
erS
up
ply
T1
Ro
ller
T2
Ro
ller
Ch
arg
erR
olle
r
Dev
elo
per
_1st
Dev
elo
per
_2n
dD
evel
op
er_
3rd
De
velo
pe
r_4
th
Dev
eD
rive
CN
1
CN
6
CN
2C
N7
CN
3
CN
8
CN
4
CN
9C
N5
V1
CN
11
TA
B1
V2
V3
V4
12 3
4 5 6
7
8 9 a
11
12a
10
15 161718192021222324142627282930313237 36 35 34 33
H.V
(T1)
H.V
(T2)
H.V
(Cha
rge
r)H
.V(D
eve
Sup
ply
)
9b 9 c 9d
12b
12c
12d
13a
13b
13c
13d
H.V
(1st
De
veS
upp
ly)
H.V
(2n
dD
eve
Sup
ply)
H.V
(3rd
De
veS
up
ply
)H
.V(4
thD
eve
Sup
ply
)
So
len
oid
(T2
ho
me)
So
len
oid
(T1
Cle
an)
*H
.V:H
igh
Vo
ltage
Po
we
rIn
let
&S
wit
ch
Se
nso
r(T
em
p2)
Eng
ine
&V
ideo
Con
trol
ler
(MA
INB
D)
CN
7
CN
5
CN
27
CN
25
CN
30
CN
3
CN
29
CN
2
CN
4
CN
9
CN
6
CN
8
CN
11
CN
12
CN
26
CN
16
CN
21
CN
31
CN
33
CN
23
CN
32
CN
24
CN
35
CN
10
CN
28
CN
14
CN
17
CN
15
CN
1338
CN
38
CN
37
11-2
CONNECTION DIAGRAM
Samsung ElectronicsService Manual
<S
ign
alN
ame
Tab
le>
*D
ir:
Sig
na
ld
ire
ctio
n,N
C:
No
Co
nne
ctio
n*
<-
:s
ame
sign
al_
na
me
1M
ain
BD
(CN
30)
SM
PS
(CO
N4)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
2+
24
VF
2+
24
VF
1+
24
VF
3+
24
VF
4+
24
VF
4+
24
VF
3+
24
VF
5A
GN
D6
GN
D
6A
GN
D5
GN
D7
AG
ND
8G
ND
8A
GN
D7
GN
D
9+
24
V1
0+
24
V1
0+
24
V9
+2
4V
11
AG
ND
12
GN
D1
2A
GN
D1
1G
ND
13
+3
.3V
14
+3
.3V
14
+3
.3V
13
+3
.3V
15
+3
.3V
16
+3
.3V
16
+3
.3V
15
+3
.3V
17
DG
ND
18
GN
D
18
DG
ND
17
GN
D1
9D
GN
D2
0G
ND
20
DG
ND
19
GN
D
21
+5
V2
2+
5V
22
+5
V2
1+
5V
23
DG
ND
24
GN
D2
4D
GN
D2
3G
ND
25
nF
US
ER
ON
26
<-
26
NC
25
NC
2S
MP
S(C
ON
3)S
wit
ch
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
V<
-2
NC
<-
3+
24
VF
<-
3S
MP
S(C
ON
2)F
use
rU
nit
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1C
ON
2<
-2
NC
<-
35
09
6-0
2C<
-
4M
ain
BD
(CN
28)
Fu
ser
Un
it
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1A
N_F
US
ER
1_O
UT
<-
2A
N_F
US
ER
1_O
UT2
<-
5M
ain
BD
(CN
14)
Sw
itch
(Lef
tco
ver)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
5V
<-
2+
5V
L<
-
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
2+
24
VF
12
4V
4A
GN
D3
GN
D
6P
WM
_A
C_
VP
P5
AC
_V
pp
_P
WM
8P
WM
_T
27
T2_
PW
M
10
PW
M_
CH
AR
GE
9C
HA
RG
E_
PW
M1
2E
NB
_DE
VE
_AC
11
DE
V_R
EM
_PW
M
14
A_
RE
AD
_T
11
3T
1_R
EA
D
16
GN
DD
15
GN
DD
Mai
nB
D(C
N7)
HV
PS
(CN
1-2
)1
+2
4V
F2
24
V
3A
GN
D4
GN
D5
EN
B_T
26
T2_
EN
7P
WM
_A
C8
AC
_P
WM
9P
WM
_T
11
0T
1_P
WM
11
PW
M_
DE
VE
12
DE
VE
_PW
M1
3A
_R
EA
D_
CH
A1
4C
HA
RG
E_
RE
AD
15
+5
V1
6+
5V
11-3Samsung Electronics
Connection Diagram
Service Manual
7M
ain
Boa
rd(C
N37
)D
eve
OE
MK
ey(C
N1)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1A
GN
D2
AG
ND
2+
24
VF
1+
24
VF
3n
WS
T_
AG
T4
nW
ST
_A
GT
4A
_W
ST
_A
GT
3A
_W
ST
_A
GT
5+
5V
L6
+5
VL
6D
eve
_Cru
m_
SC
L5
De
ve_C
rum
_S
CL
7D
eve_
Cru
m_S
DA
8D
eve_
Cru
m_S
DA
8A
GN
D7
AG
ND
8D
eve
OE
MK
ey(C
N2)
DC
Mot
or
(Was
teA
git
ato
r)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
WS
T_
AG
T<
-
2N
C<
-3
SE
NS
E_A
GT
<-
9aD
eve
OE
MK
eyD
eve
Ca
rtri
dge
(1st
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
V1
DE
VE
_CR
UM
_SD
AD
EV
E_C
RU
M_
SD
AV
2D
GN
DD
GN
D
V3
SC
L_O
UT
2S
CL
_O
UT
1
9bD
eve
OE
MK
eyD
eve
Ca
rtri
dge
(2n
d)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
V4
DE
VE_C
RU
M_S
DA
DE
VE
_CR
UM
_S
DA
V5
DG
ND
DG
ND
V6
SC
L_O
UT
2S
CL
_O
UT
2
9cD
eve
OE
MK
eyD
eve
Ca
rtri
dge
(3rd
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
V7D
EVE
_CR
UM
_SD
AD
EV
E_C
RU
M_S
DA
V8
DG
ND
DG
ND
V9
SC
L_O
UT
2S
CL
_O
UT
3
9 dD
eve
OE
MK
eyD
eve
Ca
rtri
dge
(4th
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
V10
DE
VE_C
RU
M_S
DA
DE
VE_
CR
UM
_SD
AV
11
DG
ND
DG
ND
V1
2S
CL
_OU
T2
SC
L_
OU
T4
10M
ain
BD
(CN
5)D
eve
Driv
e(C
N1)
Pin
Dir
Pin
1A
GN
D2
AG
ND
2+2
4VF
124
V
3A
GN
D4
AG
ND
4+2
4VF
324
V
5nS
OL_
DE
VE
_1S
T6
AG
ND
6nS
OL_
DE
VE
_2N
D5
24V
7nS
OL_
DE
VE
_3R
D8
DG
ND
8nS
OL_
DE
VE
_4TH
75V
9nC
LT_D
EVE
_1S
T10
nSO
L_D
EV
E_1
ST
10nC
LT_D
EVE
_2N
D9
nSO
L_D
EV
E_2
ND
11nC
LT_D
EVE
_3R
D12
nSO
L_D
EV
E_3
RD
12nC
LT_D
EVE
_4TH
11nS
OL_
DE
VE
_4TH
11M
ain
Bo
ard
BL
DC
Mo
tor(
De
ve)
Pin
Dir
Pin
12
4V
1+
24
V
22
4V
2+
24
V
3A
GN
D3
PG
ND
4A
GN
D4
PG
ND
5D
GN
D5
SG
ND
65
V6
+5
V
7S
TA
RT
7S
TA
RT
8R
EA
DY
8R
EA
DY
9C
LO
CK
9C
LO
CK
10
CW
/CC
W
Sig
nal
Nam
eS
ign
al N
ame
Sig
nal
Nam
eS
ign
al N
ame
11-4
CONNECTION DIAGRAM
Samsung ElectronicsService Manual
12a
De
veD
rive
(CN
6)S
ole
no
id(D
eve
1st)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
SO
L_
DE
V_
1S
T<
-
2N
C<
-3
AG
ND
<-
12b
De
veD
rive
(CN
2)S
ole
no
id(D
eve
2nd
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
SO
L_
DE
V_
2N
D<
-
2N
C<
-
3A
GN
D<
-
12c
De
veD
rive
(CN
7)S
ole
no
id(D
eve
3rd
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
SO
L_
DE
V_
3R
D<
-2
NC
<-
3A
GN
D<
-
12d
De
veD
rive
(CN
3)S
ole
no
id(D
eve
4th
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
SO
L_
DE
V_
4T
H<
-2
NC
<-
3A
GN
D<
-
13a
De
veD
rive
(CN
8)C
lutc
h(D
eve
1st)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
CLT
_DE
V_
1ST
<-
2N
C<
-3
AG
ND
<-
13b
De
veD
rive
(CN
4)C
lutc
h(D
eve
2nd
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
CLT
_DE
V_
2ND
<-
2N
C<
-
3A
GN
D<
-
13c
De
veD
rive
(CN
9)C
lutc
h(D
eve
3rd
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
CLT
_DE
V_
3RD
<-
2N
C<
-
3A
GN
D<
-
De
veD
rive
(CN
5)C
lutc
h(D
eve
4th
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
CLT
_DE
V_
4TH
<-
2N
C<
-
3A
GN
D<
-
14M
ain
Bo
ard
(CN
35)
So
len
oid
(T1
cle
an)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
SO
L_
T1
_C
LN
<-
2N
C<
-
3A
GN
D<
-
15M
ain
BD
(CN
29)
Fan
Mo
tor(
Fu
ser)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
FA
N_
FU
SE
R<
-
2N
C<
-3
+2
4V
F<
-
16M
ain
BD
(CN
27)
BL
DC
Mo
tor(
Mai
n)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
1+
24
V
2+
24
VF
2+
24
V
3A
GN
D3
PG
ND
4A
GN
D4
PG
ND
5D
GN
D5
SG
ND
6+
5V
6+
5V
7n
BL
DC
_S
TA
RT
17
ST
AR
T8
nB
LD
C_
RD
Y1
8R
EA
DY
9B
LD
C_
CL
K1
9C
LO
CK
10
DG
ND
10
CW
/CC
W
13d
11-5Samsung Electronics
Connection Diagram
Service Manual
17M
ain
BD
(CN
3)IE
EE
128
4P
ort
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
ST
B<
-
2D
AT
A0
<-
3D
AT
A1
<-
4D
AT
A2
<-
5D
AT
A3
<-
6D
AT
A4
<-
7D
AT
A5
<-
8D
AT
A6
<-
9D
AT
A7
<-
10
nA
CK
<-
11
BU
SY
<-
12
PE
RR
OR
<-
13
SE
LE
CT
<-
14
nA
UT
OF
D<
-
15
NC
<-
16
DG
ND
<-
17
AG
ND
<-
18
5V
1<
-
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
19
DG
ND
<-
20
DG
ND
<-
21
DG
ND
<-
22
DG
ND
<-
23
DG
ND
<-
24
DG
ND
<-
25
DG
ND
<-
26
DG
ND
<-
27
DG
ND
<-
28
DG
ND
<-
29
DG
ND
<-
30
DG
ND
<-
31
nIN
IT<
-3
2n
FA
UL
T<
-
33
NC
<-
34
NC
<-
35
NC
<-
36
nS
EL
EC
TIN
<-
18M
ain
BD
(CN
2)
US
BP
ort
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1V
BU
S_2
27
0V
BU
S
2D
ND
-
3D
PD
+4
DG
ND
AG
ND
5A
GN
DF
GN
D6
AG
ND
FG
ND
19M
ain
BD
(CN
4)
Pan
el(C
N2)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1D
GN
D1
DG
ND
2+
5V
2V
CC
3P
AN
EL_
TX
3O
PE
_R
XD
4n
RS
T_
PA
NE
L4
/OP
E_
RS
T
5P
AN
EL_
RX
5O
PE
_T
XD
11-6
CONNECTION DIAGRAM
Samsung ElectronicsService Manual
20M
ain
BD
(CN
9)N
PC
(J1)
(Net
wo
rkP
rin
tC
ard
)P
inS
ign
al
Na
me
Dir
Pin
Sig
na
lN
am
e
1+
3.3
V1
VD
D3
2+
3.3
V2
VD
D3
3D
GN
D3
GN
D
4n
NP
C_
CS
4n
XP
CS
5D
AT
A(3
1)
5X
PD
ata
(31
)
6D
AT
A(3
0)
6X
PD
ata
(30
)
7D
AT
A(2
9)
7X
PD
ata
(29
)8
DG
ND
8G
ND
9D
AT
A(2
8)
9X
PD
ata
(28
)1
0D
AT
A(2
7)
10
XP
Dat
a(2
7)
11
DA
TA
(26
)1
1X
PD
ata
(26
)
12
DG
ND
12
GN
D1
3D
AT
A(2
5)
13
XP
Dat
a(2
5)
14
DA
TA
(24
)1
4X
PD
ata
(24
)1
5n
NP
C_
INT
15
nX
IRQ
_OU
T
16
DG
ND
16
GN
D1
7A
_A
DD
R(5
)1
7X
PA
dd
r(3)
18
A_
AD
DR
(4)
18
XP
Ad
dr(
2)
19
A_
AD
DR
(3)
19
XP
Ad
dr(
1)2
0+
3.3
V2
0V
DD
3
21
NC
21
NC
22
DA
TA
(23
)2
2X
PD
ata
(23
)
23
DA
TA
(22
)2
3X
PD
ata
(22
)
24
NC
24
NC
25
DA
TA
(21
)2
5X
PD
ata
(21
)
26
NC
26
NC
27
DA
TA
(20
)2
7X
PD
ata
(20
)
28
A_
AD
DR
(15)
28
XP
Ad
dr(
13)
29
DA
TA
(19
)2
9X
PD
ata
(19
)
30
A_
AD
DR
(14)
30
XP
Ad
dr(
12)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
31
DA
TA
(18
)3
1X
PD
ata
(18
)
32
A_
AD
DR
(13)
32
XP
Ad
dr(
11)
33
DA
TA
(17
)3
3X
PD
ata
(17
)
34
A_
AD
DR
(12)
34
XP
Ad
dr(
10)
35
DA
TA
(16
)3
5X
PD
ata
(16
)
36
A_
AD
DR
(11)
36
XP
Ad
dr(
9)
37
A_
AD
DR
(6)
37
XP
Ad
dr(
4)3
8A
_A
DD
R(1
0)3
8X
PA
dd
r(8)
39
nN
PC
_R
ST
39
nR
ES
ET
_P4
0A
_A
DD
R(9
)4
0X
PA
dd
r(7)
41
nW
AIT
41
nX
PW
AIT
42
A_
AD
DR
(8)
42
XP
Ad
dr(
6)
43
NC
43
NC
44
A_
AD
DR
(7)
44
XP
Ad
dr(
5)4
5N
C4
5N
C
46
NC
46
NC
47
NC
47
NC
48
DG
ND
48
GN
D
49
NC
49
NC
50
nR
D5
0n
XP
RE
51
nW
R5
1n
XP
WE
52
DG
ND
52
GN
D
53
NC
53
NC
54
NC
54
NC
55
NC
55
NC
56
DG
ND
56
GN
D5
7n
PR
T_
IRQ
57
nX
IRQ
_IN
58
DG
ND
58
GN
D5
9D
GN
D5
9G
ND
60
DG
ND
60
GN
D
21M
ain
BD
(CN
16)
SC
FU
nit
(CN
9)
(Se
con
dar
yC
asse
tte
Fee
der
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
3.3
V2
ST
S_S
CF
2S
CF
_S
TS
3C
MD
_S
CF
3S
CF
_C
MD
4C
LK
_SC
F4
SC
F_
CL
K
5R
DY
_S
CF
5S
CF
_R
DY
6+
24
V6
24
VS
7D
GN
D7
DG
ND
8A
GN
D8
AG
ND
22M
ain
BD
(CN
21)
Sen
sor(
Pap
erE
mpt
y)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
<-
2n
S_
EM
PT
2<
-
3D
GN
D3
<-
4N
C4
<-
23M
ain
BD
(CN
31)
Sen
sor(
MP
Em
pty
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
<-
2n
S_
MP
_E
MP
T2
<-
3D
GN
D3
<-
4N
C4
<-
11-7Samsung Electronics
Connection Diagram
Service Manual
24M
ain
BD
(CN
33)
Sen
so
r(F
eed
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
<-
2n
S_
FE
ED
2<
-
3D
GN
D3
<-
26M
ain
BD
(CN
23)
Clu
tch
(Fee
d)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
<-
2n
CLT
_FE
ED
<-
27M
ain
BD
(CN
25)
So
len
oid
(Pic
ku
p)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
<-
2n
SO
L_
PIC
KU
P<
-
28M
ain
BD
(CN
32)
So
len
oid
(MP
)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
<-
2n
SO
L_
MP
<-
3N
C<
-
29M
ain
BD
(CN
24)
So
len
oid
(Du
ple
x)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
24
VF
<-
2n
SO
L_
DU
P<
-
30M
ain
BD
(CN
26)
So
len
oid
(T2
ho
me)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
<-
2N
C2
<-
3n
SO
L_
T2
3<
-
31M
ain
BD
(CN
17)
Sen
sor
(Was
teT
on
er)
&E
xit
Sen
sor
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
3.3
V1
<-
2D
GN
D2
<-
3n
S_
TO
NE
R_
RX
1<
-
4D
GN
D2
<-
5+
3.3
V1
<-
6n
S_
EX
IT2
<-
7D
GN
D3
<-
32M
ain
BD
(CN
15)
Sen
sor
(Tem
per
atu
re)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1A
_T
EM
P1
<-
2G
ND
A2
<-
33M
ain
BD
(CN
10)
ITB
Un
it(D
raw
er
Co
nn
ect
or
on
Fra
me)
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
5V
LJ
7<
-
2n
S_
ITB
_H
OM
EJ
6<
-3
DG
ND
J5
<-
4A
_IT
B_
HO
ME
J4
<-
5D
GN
DJ
3<
-
6IT
B_
CR
UM
_S
CL
J14
<-
7IT
B_
CR
UM
_S
DA
J13
<-
11-8
CONNECTION DIAGRAM
Samsung ElectronicsService Manual
34M
ain
BD
(CN
12)
LS
U
*L
DP
art
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1n
HS
YN
C1
*HS
YN
C
2+
5V
L2
+5
V3
DG
ND
3G
ND
4n
LD
ON
_L
SU
4*L
DO
N5
VD
O_
LSU
+5
*VID
EO
+
6V
DO
_LS
U-
6*V
IDE
O-
7n
SH
_LS
U7
*S/H
*M
oto
rD
riv
er8
CL
K_L
SU
1C
LK
9n
RD
Y_
LS
U2
*RE
AD
Y
10
nS
TA
RT
_L
SU
3*S
TA
RT
11
AG
ND
4G
ND
12
+2
4V
5V
CC
35M
ain
BD
(CN
11)
PT
L(C
N1
)&T
emp
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1+
5V
1<
-
2E
N_
ER
AS
ER
2<
-3
A_
TE
MP
21
<-
4G
ND
A3
<-
37M
ain
BD
(CN
6)O
PC
Un
it
Pin
Sig
na
lN
am
eD
irP
inS
ign
al
Na
me
1A
_O
PC
_KE
Y<
-
2D
GN
D<
-
3.3V
Page:
Size:
REV:
ED.
C
ENG.
F
A
1 5
CHANGE PART
1
B
F
SPGPm
D
B
ED NO.
4
DATE
E
B
B
’04.09.02
7
REVISION RECORD
Bigbang Plus
SAMSUNG ELECTRONICS
ARP.
8
Bingbang Plus
4
NC
SIGN
1 7
DRW.
1.8V
Drawing Number:
CHK:
MAIN
6
Remove RA for CLP-511/511G
S.D AN
CONFIDENTIAL
2
D
6
E
3
C.B.LEE
8
B
A
B5
Rev 1.0
2
1/16
A3
C.B.LEE
C.B.LEE
C
TITLE:
3
56R35
3
DGND
120
R35
2
100p
F
C28
0
R275
39
DGND
BG_K17
1uH
L33
LK16081ROK-T
DG
ND
SDCLK1
16V
BG_V19
C22100uF
BG
_K1
+3.3V
3711-003410
CN1-1
1
BG_V9
BG_Y20
BG_P18
BG_C15
100nF
C41
DGND
100nF
C8
100nF
C61
BG_U12
BG_L18
BG_Y16
C20
BG
_L20
100nF
BG
_V3
BG_F20
10K
R38
TP856
BG_A19
BG_P17
+3.3V
BG_V8
BG
_W1
2007-007004|R1608_RESR48 12K
DGND
R5939
BG
_W3
100nF
C69 C44
100nFGND 2
IN
1
OUT
3
BG
_G3
+3.3V
STS104BF1
BG_T2
16V470uFC87
STS104BF4
2901-001178
GND 2
IN
1
OUT
3
BG_W16
C279 100pF
C64
100nF
BG_E4
BG_W12
1.8V
100nF
C39
C74
100nF
BG_W19
C76
R237 10K
100nF
BG_M19
BG_C17
BG_Y9
BG
_E3
BG_F19
100R5
BG_V14
R3
10K
BG_G19
3_3V2
BG_P20
BG
_F3
BG_A20
BG_V16
100nF
C66
BG_V12
R87
10K
4
R60
10K
BG_C19
BG_Y17
BG_M20
2
BG_Y12
22pFC196
BG_Y14
BG_Y18
BG_W13
+3.3V
100nF
C75
BG
_H2
DGND
BG_U9
BG_G18
BG_B6
DGND
C43
100nF
BG
_H3
BG_U14
100nF
BG
_V4
C58
BG_B12
BG_G20
R274
DGND
39
C48
100nF
nSTROBE
Y9nTxD0
V10nTxD1/TDO/GPO10
M19nWAIT0/PDE
A12nWE
R3nWR
NPSYNC1
nROMCS3/nIOCS3/GPO1
G17
nRS
TO
UT
/MC
LKO
UT
/GP
O0
V9nRxD0
nRxD1/TDI/GPI17W9
nSCS0J17
H18nSCS1
H20nSCS2
R19nSELECTIN
M17
nLREADY/nEBSYP17
E17nRAS
R2nRD
K20
nRE
SE
T
nROMCS0T1T2
nROMCS1P3
nROMCS2P4
nINIT
Y1nIOCS0
Y2nIOCS1
Y4nIOCS2/nDACK0/GPO2
nIOCS4/nSCS3/GPO4G20
M20nIOCS5/nSCS4/GPO3/TONEOUT
U12nLFPHA0/CCLK
V12nLFPHB0/nCMSGnLFPHB1/nPRINT
W12
K17
L20
nDR
EQ
0/A
DD
R23
/GP
I0
nDREQ1/DQM4/GPO8J19
nDREQ2/DQM6/GPO6J20
nEMSG/nDACK3/PWMOUT3N18
L18nFAULT
nFSYNC/nLFPHA1N19
N20nHSYNC
Y20
VS
SL
W20
VS
S_A
DC
VS
S_P
LL1
C2
D14
VS
S_P
LL2
F19nACK
K18nAUTOFD
H19nCAS
nDACK1/DQM5/GPO7E20
nDACK2/DQM7/GPO5
B15
VD
D_P
LL2
E2
VD
D_R
ING
_OS
C
A16
VD
D_U
SB
1D
20V
DD
_US
B2
W13VDO
B17
VS
SB
A17
VS
SC
A19Y3
VD
D_C
OR
E2
Y7
VD
D_C
OR
E3
Y11
VD
D_C
OR
E4
U20
VD
D_C
OR
E5
T19
VD
D_C
OR
E6
T20
VD
D_C
OR
E7
J18
VD
D_C
OR
E8
D2
VD
D_P
LL1
VD
D3_
US
B
B16
VD
DB
VD
DC
C16
B18
VD
DL
VD
D_A
DC
V20 N3
VD
D_A
RM
1W
7V
DD
_AR
M2
J4V
DD
_CO
RE
0R
1V
DD
_CO
RE
1
VC
C3
U6
VC
C4
U10
VC
C5
D11
VC
C6
D15
VC
C7
U15
VC
C8
F17
VC
C9
Y19VCLK
A18
TX_EN/TXEN_10M
C15UCLK
R18VBUS
F4
VC
C0
K4
VC
C1
L17
VC
C10
R17
VC
C11
R4
VC
C2
D6
V13
W10
TE
ST
MO
DE
Y10
TE
ST
SE
TXCLK/TXCLK_10M/GPI18V15
TXD0/nIOCS3V16
TXD1/GPO12W16Y16
TXD2/GPO13TXD3/GPO14
W15Y15
B4
SD
6C
4S
D7
SD
8B
5
C5
SD
9
B8SDCLK0
B6SDCLK1
G18SLCT_OUT
SPD/nDREQ3
SD
26C
10S
D27
D10
SD
28A
11S
D29
A3
SD
3
B11
SD
30C
11S
D31
B3
SD
4A
4S
D5
C3
SD
2
C8
SD
20
SD
21A
9
B9
SD
22C
9S
D23
D9
SD
24A
10S
D25
B10
A5
SD
12C
6S
D13
SD
14A
7
B1
SD
15C
7S
D16
D7
SD
17A
8S
D18
B7
SD
19
C14SA6
F18SA7
A14SA8
E19SA9
A2
SD
0B
2S
D1
D5
SD
10A
6S
D11
SA0
C12SA1
E18SA10SA11
A15D19
SA12
B13SA2
C13SA3
A13SA4
B14SA5
A20
RXCLK/RXCLK_10M/GPI19V18
RXD0/GPI21Y12Y13
RXD1/GPI22V17
RXD2/GPI23RXD3/GPI24
W17
RXERR/GPI25W11
U11RX_DV/LINK_10M/GPI20
D12M18
PD5
U16PD6
P18PD7
K19PERROR
P20PWMOUT0
P19PWMOUT1
W18PWMOUT2
RR
EF
LSUCLK/nCBSY/GPO11
E4
MC
LK
U14MDC/GPO15MDIO/GPI26
V14
F20PD0
W19PD1
Y18PD2
L19PD3
Y17PD4
GN
D30
V11
GN
D31
U4
GN
D4
D8
GN
D5
U8
GN
D6
GN
D7
D13
U13
GN
D8
D17
GN
D9
R20
GN
D23
L12
GN
D24
M9
GN
D25
M10
GN
D26
M11
GN
D27
M12
GN
D28
G4
GN
D29
N4
GN
D3
T18K9
GN
D17
K10
GN
D18
K11
GN
D19
H4
GN
D2
K12
GN
D20
L9G
ND
21L1
0G
ND
22L1
1
D4
GN
D1
H17
GN
D10
N17
GN
D11
U17
GN
D12
GN
D13
J9 J10
GN
D14
J11
GN
D15
J12
GN
D16
C18
C19DQM1
D18DQM2
B19DQM3
EINT0/TnRSTV8
EINT1/TCKW8
EINT2/nRXD2/TMSY8
U9EINT3/nTXD2/GPO9
A1
GN
D0
H3
DA
TA
5/G
PI6
E3
C1
DA
TA
6/G
PI7
DA
TA
7/G
PI8
F1
F2
DA
TA
8/G
PI9
DA
TA
9/G
PI1
0F
3
C17DMNS
D16DPLS
DQM0
L4 N1
DA
TA
27N
2D
AT
A28
M3
DA
TA
29
P2
DA
TA
2/G
PI3
M4
DA
TA
30P
1D
AT
A31
DA
TA
3/G
PI4
E1
DA
TA
4/G
PI5
J3
DA
TA
1/G
PI2
D1
L1D
AT
A20
L2D
AT
A21
K3
DA
TA
22M
1D
AT
A23
M2
DA
TA
24L3
DA
TA
25
DA
TA
26
G3
DA
TA
12/G
PI1
3
DA
TA
13/G
PI1
4K
1
H1
DA
TA
14/G
PI1
5
DA
TA
15/G
PI1
6H
2
K2
DA
TA
16J1
DA
TA
17J2
DA
TA
18
DA
TA
19B20
BA1
G19BUSY
B12CKE
W14COL/COL_10M/EINT4
Y14CRS/CRS_10M/nWAIT1
DA
TA
0/G
PI1
D3
G1
DA
TA
10/G
PI1
1
DA
TA
11/G
PI1
2G
2
U5
AD
DR
7W
5A
DD
R8
Y5
AD
DR
9
T17AIN0
U18AIN1
U19AIN2
V19ATEST_OUT
C20BA0
AD
DR
19
W6
AD
DR
2
W2
AD
DR
20W
3A
DD
R21
W4
AD
DR
22
Y6
AD
DR
3V
6A
DD
R4
V7
AD
DR
5U
7A
DD
R6
AD
DR
11U
1A
DD
R12
AD
DR
13U
2
U3
AD
DR
14V
1A
DD
R15
V2
AD
DR
16V
3A
DD
R17
V4
AD
DR
18W
1
U10
JC13-00014C
SPGPm
V5
AD
DR
1
T3
AD
DR
10T
4
BG_Y4
100nF
C83
2203-000189|R1608_CAP
DGND
BG
_W2
100nF
C73
BG_N18
BG_B8
C54
100nF
DGND
BG_Y13
BG_G17
+5V
C200470uF16V
C40
100nF
+3.3V
R1
10K
2007-000090|R1608_RES
BG
_F1
+3.3V_V2
C199220uF16V
NC23015pF
10K
R41
BG_R18
10K
R2
100nF
C67
DGND
C47
100nF
39R273
39
R40
NWR1
BG
_H1
DGND
BG_R3
BG
_F2
BG_K20
BG
_W4
BG_P3
BG_T17
BG
_W10
100
BG
_G1
R4
R47
10KBG
_D1
R53
10K
R272 39
R44
39
R5810K
BG_C18
BG_J17
39R276
BG_V10
10K
R45
BG_M18
C72
100nF
BG_U19
22pF C202
BG_N20
R570
10K
R34
BG_M17
DGND
BG_R2
+3.3V
DGND
BG_U18
BG_R19
BG
_W6
BG_P19
BG_Y15
BG
_C1
B120L42
BG_K18
DGND
C77
100nF
BG
_P2
BG_W9
3
BG
_V5
BG_K19
DGND
BG_T1
BG
_V2
BG_D16
100nFC94
C21100nF
R6
10K
100nF
BG
_D3
BG_N19
C42
10K
RA49
+3.3V
63mW
BG_R20
10K
R46
BG
_E1
BG_U16
BG_L19
C201
10KR238
+5V
22pF
C59
C55DGND
100nF
SDCLK0
100nF
1203-002220
U4
1
GND
3 IN OUT2
BG_W15
LD1117DT
BG_Y19
BG
_Y10
NC310pF
BG
_G2
DGND
100p
FC
323
100p
FC
322
DGND
R52
10K
BG_Y1
BG_W18
DGND
C45
100nF
nINIT
nSTROBE
nWAIT
nVDI_LPEC
SERIAL_RXD
S_D
AT
A(2
6)
S_D
AT
A(2
7)
S_D
AT
A(2
8)
S_D
AT
A(2
9)
S_D
AT
A(3
1)
S_D
AT
A(3
0)SDCLK0
S_DATA(0:31)ADDR(1:23)SD(0:31)
nAUTOFD
SDCLK1
nSELECTINS
_DA
TA
(16)
S_D
AT
A(1
7)
S_D
AT
A(1
8)
S_D
AT
A(1
9)
S_D
AT
A(2
0)
S_D
AT
A(2
1)
S_D
AT
A(2
2)
S_D
AT
A(2
3)
S_D
AT
A(2
4)
S_D
AT
A(2
5)
S_D
AT
A(5
)
S_D
AT
A(6
)
S_D
AT
A(7
)
S_D
AT
A(8
)
S_D
AT
A(9
)
S_D
AT
A(1
0)
S_D
AT
A(1
1)
S_D
AT
A(1
2)
S_D
AT
A(1
3)
S_D
AT
A(1
4)
S_D
AT
A(1
5)
nROMCS0
nRDnWR
S_D
AT
A(0
)
S_D
AT
A(1
)
S_D
AT
A(2
)
S_D
AT
A(3
)
S_D
AT
A(4
)
AD
DR
(10)
AD
DR
(11)
AD
DR
(12)
AD
DR
(13)
AD
DR
(14)
AD
DR
(15)
AD
DR
(16)
nNPC_CS
SERIAL_TXD
nUSB_CS
nUSB_IRQ
SA(0:12)
nUSB_DACK
AD
DR
(2)
AD
DR
(3)
AD
DR
(4)
AD
DR
(5)
AD
DR
(6)
AD
DR
(7)
AD
DR
(8)
AD
DR
(9)
UCLK
ADDR(18)ADDR(19)ADDR(20)
ADDR(22)
ADDR(17)
ADDR(23)
nPRT_IRQ
ADDR(21)
nNPC_INT
ADDR(1)
S_nSCS0nSCS1nSCS2
nUSB_REQ
BA1BA0
PDE
nACKBUSYPERRORSLCT_OUTnFAULT
PD(0:7)
DNVBUS
DP
nS_ITB_HOME
PANEL_RXPANEL_TX
CSSKDInNPC_RST
nCASnRASDQM0DQM1DQM2DQM3
CKE
nWE
AD
DR
(1)
nCS_LPEC
nRST_PANEL
nUSB_RST
TEST_LED1
DO
nPSYNC
VCLKnHSYNC
nRESETMCLK
SA(10)SA(11)SA(12)
PD(1)
PD(0)
PD(2)
PD(3)
PD(4)
PD(5)
PD(6)
PD(7)
AD
DR
(23) S
D(5
)
SD
(4)
SD
(3)
SD
(2)
SD
(1)
SD
(0)
SA(1)SA(0)
SA(2)SA(3)SA(4)SA(5)SA(6)SA(7)SA(8)SA(9)
SD
(21)
SD
(20)
SD
(19)
SD
(18)
SD
(17)
SD
(16)
SD
(15)
SD
(14)
SD
(13)
SD
(12)
SD
(11)
SD
(10)
SD
(9)
SD
(8)
SD
(7)
SD
(6)
AD
DR
(20)
AD
DR
(21)
AD
DR
(22)
AD
DR
(19)
AD
DR
(18)
AD
DR
(17) SD
(30)
SD
(31)
SD
(29)
SD
(28)
SD
(27)
SD
(26)
SD
(25)
SD
(24)
SD
(23)
SD
(22)
SAMSUNG ELECTRONICS
C
3
5 82 7
D
0.9%1.2%
Rev 1.0
D
1
DRW.
Size:
ENG.
RESERVED
F
E
B
Page:
[ VCLK SYSCLK ]
B
[ RESET ]
ED.
MHz
B
Bingbang Plus
ARP.
61
4 6
TITLE:
’04.09.02
C
REVISION RECORD
E
FRSEL
ED NO.
B
S1=MS0=0
MAIN
5
CHANGE PART
B
7
S1=0
3
8
A
F
CHK:
[ MAIN SYSCLK ]
S.D AN
0.5%
CONFIDENTIAL
RESET & CLK
B
S0=1
1
Drawing Number:
* M= Floating
12-14
A
DATE
SIGN
S0=MS1=0
23.88MHz
1 0.4%
S1=0
RESERVED
4
C.B.LEE
REV:
S0=0
2
GND
21
NC
OUT34
VCC
2/16
A3
C.B.LEE
C.B.LEE
10nF
COS345CTS-23.8807363OSC3
C118
100R55
C109 NC20315pF100nF
10KR92
NC22933pF
DGND
OSC1
ATS-49/U,12MHz,50ppm2801-003886
C918pF
STS104B
F3
GND2
IN
1
OUT
3
NR80
STS104B
F6
GND 2
IN
1
OUT
3
DGND
R30
DGND
+3.3V
DGND
NF5STS104B
2901-001178
2GND
1
IN
3
OUT
39
DGND
+3.3V
DGND
DGND
C8433pF
2804-001536
GND
21
NC
OUT34
VCC
R72
COS-000607-12.000MNOSC2
C25
DGND
200
10uF100nF
VDD 72 VSS
XIN/CLKIN1 XOUT 8
C28
16V
1205-002339
FRSEL 6
4 S0
S13
SSCLK 5
C122100nF
CY25811
U37
0
R67
R347
+3.3V
+3.3V
0
DGND
+3.3V
DGND
+3.3V
DGND
100nFNC95
DGND
DGND
DGND
NR9
+3.3V
0
DGND
18pFC10
5
OUT
8
VCC
DGND
2804-001568
NOSC3
DXO-3NH,19.900614MHZ
4
GNDNC
1
NR70
10pFNC6
DGND
NC510pF
1203-002233|sot_23_R
U15
XC61FN3112MR
Vin3Vout 1
Vss 2 L17
3301-000325|R3225_BEAD
B60
0L3
2
DGND
UCLK
nRESET
MCLK
VCLK
MEMORY
B
B
TITLE:
ENG.
B
REV:
DIP
ED.
MAIN
1
2
REVISION RECORD
SAMSUNG ELECTRONICS
B
8
5
F
4
CHANGE PART
B
SIGN
8
C.B.LEE
B3
2
ARP.
’04.09.02
CONFIDENTIAL
A
DATE
D
Bingbang Plus
4
A3
C.B.LEE
C.B.LEE
6
6
* FACTORY OPTION
5
Page:Drawing Number:
3
CHK:
7
1
1
SOCKET
S.D AN
C
7
ED NO.
A
D
Rev 1.0DRW.
E
Size: F
C
E
3/16
100nF
C102
100nF
100nF
C96
C98
2
4
6
8
39R73
46
RA12 39 1/16W
DQ23
100nF
C62
R810K
10K
R37
16A8 17
nWE 28
A6
70
nRAS72
68
A13
69
BA0
66A967
A11
A7
100nF
C106
8
100nF
C88
1/16W
2
4
6
DGND
RA25 392
4
6
8
1/16W39RA24
100pF
C7
+3.3V
R43
19
39
A10/AP 18BA1
C51
VSS
71251-100
51
100nF
24
DIMM1-1
VSS
3709-001131
1
+3.3V
22
RFU
C208
VERF
10nF
R292
C107
100nF
33
100pF
DGND
DGND
C14
86
DQ2488
NC85VSS
NC8483
NC82
VDD81
NC
nS179
DQMB161
C49
100nF
C123
100nF
DO4
GND56
ORG
2SK
8VCC
M93C86-WBN6T
U36
1103-001328
CS1
DC7
3DI
6
8
+3.3V
R17
10K
39 1/16W
2
4
100nF
C92
RA7
+3.3V
C53100nF
100nF
C65
C18
2
4
6
8
100pF
8
RA30 39 1/16W
1/16W39RA272
4
6
R42 39
12A0 13
VSS
11
DQ7 10DQMB0
40
NU78
DQ18
75
CKE17776
CK1
RFU74
VSS
71
nCAS73
VDD
DQ17 39
DQ16 38
94
A163
93DQ29
VDD92DQ28
90DQ2791
89DQ26
DQMB387
DQ25
NC19
10NC2
NC313
NC414
37VCC
46VSS1
27VSS2
_BUSY15
47_BYTE
26_CE
_OE28
_RESET12
_WE11
29D0
D131
D1034
D1136
D1239
D1341
D1443
D1545
33D2
35D3
D438
D540
D642
D744
D830
D932
A115
A124
A133
A142
1A15
48A16
A1717
A1816
23A2
22A3
21A4
20A5
19A6
18A7
8A8
7A9
U6
29LV800 1107-001302
A025
24A1
6A10
C115100uF
16V
2
4
6
8
80
RA23
39
1/16W
99
nS3
+3.3V
SA2100
SA1
97SA098
96VSS
DQ3095DQ31
C89
100nF
NC 33
C79
100nF
C82
100nF
2
4
6
8
RA17 39 1/16W
C78
100nF
DGND
31
+3.3V
DGND
30
NC 32
VDD
29nS2
DQ3 5
nS0
3DQ2 4
DQ0 2DQ1
64
R27939
A565
A3
2
4
6
8
RA29 39
56
87
4
2
4
6
8
9
1/16W39RA8
8DQ6
DQ4 7DQ5
15
VDD 6
A2 14A4
DGND
VDD 50
47SDA 48
VSS
R234 39
RA262
4
6
8
1/16W39
100nF
C81
3
12VSSQ2VSSQ3
4652
VSSQ4
3VDDQ1VDDQ2
943
VDDQ3VDDQ4
49
VSS128
VSS241
VSS354
VSSQ16
42DQ8DQ9
44
15LDQM
NC/RFU40
UDQM39
VDD1114
VDD2VDD3
27
51DQ14DQ15
53
5DQ2DQ3
78
DQ4DQ5
1011
DQ6DQ7
13
37CLK
38
2DQ0DQ1
4
45DQ10DQ11
4748
DQ12DQ13
50
2930
A5A6
3132
A7A8
3334
A9
20BA0BA1
21
CKE
16
A02324
A1
A102235
A11
36A12
A22526
A3A4
U11
K4S561632B-TC1L
1105-001384
*CAS17
19*CS
18*RAS
*WE
+3.3V
10nF
DGND
DGND
C97
23
VDD 21
RFU
A12 20
62
59DQ1560
VSS
DQ1257
DQ14
DQ1358
54
VDD56
DQ10
100nFC17
2
4
6
8
C105
100nF
1/16W39RA28
100nF
C104
39RA19
2
4
6
8
VCC37
VSS146
VSS227
15_BUSY
_BYTE47
_CE26
28_OE
12_RESET
11_WE
1/16W
39D12
41D13
43D14
45D15
D233
D335
38D4
40D5
42D6
44D7
30D8
32D9
9NC1
NC210
13NC3
14NC4
A151
A1648
17A17
16A18
A223
A322
A421
A520
A619
A718
A88
A97
D029
31D1
34D10
36D11
1107-001302
29LV800
U9
25A0
A124
A106
5A11
4A12
3A13
2A14
49
VSS128
VSS241
VSS354
VSSQ1612
VSSQ2VSSQ3
4652
VSSQ4
40
UDQM39
VDD1114
VDD2VDD3
273
VDDQ1VDDQ2
943
VDDQ3VDDQ4
78
DQ4DQ5
1011
DQ6DQ7
1342
DQ8DQ9
44
15LDQM
NC/RFU
4
45DQ10DQ11
4748
DQ12DQ13
5051
DQ14DQ15
53
5DQ2DQ3
A7A8
3334
A9
20BA0BA1
21
CKE37
CLK38
2DQ0DQ1
2235
A11
36A12
A22526
A3A4
2930
A5A6
3132
*CAS17
19*CS
18*RAS
*WE16
A02324
A1
A10
U13
K4S561632B-TC1L
1105-001384
C60
C6
100pF
10
100nF
2
4
6
8
R74
1/16W39RA22
26CKE0 27
25VSS
100nF
C124
CK0
100nFC16
DGND
C56
100nF
55
DQ953
DQ11
49
DQ852
2
+3.3V
SCL
WSDIF-8TCN36-1
1
37
VSS 3635
DQMB2
34NC
NC
44DQ22 45
DQ21
2
4
6
8
1/16W39RA9
Place near SPGPm
10R56
R233
39
100nF
+3.3V
C50
22pFC85
42DQ20 43
41VDD
DQ19
DGND
D41MMSD914T1
8
1KR68
1/16W39RA31
2
4
6
D_SD(0)D_SD(1)
D_SD(10)D_SD(11)D_SD(12)D_SD(13)D_SD(14)D_SD(15)
D_SD(2)D_SD(3)D_SD(4)D_SD(5)D_SD(6)D_SD(7)D_SD(8)D_SD(9)
D_SA(12)
D_SA(12)
D_SA(0:12)
A_ADDR(9)
S_DATA(2)A_ADDR(8)
S_DATA(1)A_ADDR(7)
S_DATA(0)A_ADDR(6)A_ADDR(5)A_ADDR(4)A_ADDR(3)
A_ADDR(22)
nROMCS0
nROMCS0
nRDnWR
A_ADDR(21)
A_ADDR(21)
DATA(11)
A_ADDR(17)
DATA(10)A_ADDR(16)
DATA(9)A_ADDR(15)
DATA(8)A_ADDR(14)
S_DATA(7)A_ADDR(13)
S_DATA(6)A_ADDR(12)
S_DATA(5)A_ADDR(11)
S_DATA(4)A_ADDR(10)
S_DATA(3)
DATA(21)DATA(22)DATA(23)DATA(24)DATA(25)
DATA(15)
DATA(14)A_ADDR(20)
DATA(13)A_ADDR(19)
DATA(12)A_ADDR(18)
D_SD(19)D_SD(20)D_SD(21)D_SD(22)D_SD(23)D_SD(24)D_SD(25)
DATA(16)DATA(17)
DATA(26)DATA(27)
DATA(28)DATA(29)
DATA(30)
DATA(31)
DATA(18)DATA(19)DATA(20)
D_SD(14)D_SD(13)D_SD(12)
D_SD(11)D_SD(10)D_SD(9)D_SD(8)
D_SA(11)
A_ADDR(2)
D_SD(16)D_SD(17)
D_SD(26)D_SD(27)D_SD(28)D_SD(29)D_SD(30)D_SD(31)
D_SD(18)
D_DQM1
D_SA(11)D_SA(9)
D_SA(7)D_SA(5)D_SA(3)D_SA(1)
D_SD(15)
D_SD(3)D_SD(2)D_SD(1)D_SD(0)
D_DQM3
D_CLKE
D_nCASD_nRASD_BA0
D_SA(8)
D_SA(6)D_SA(4)D_SA(2)D_SA(0)
D_DQM0
D_SD(7)D_SD(6)D_SD(5)D_SD(4)
D_SD(19)D_SD(18)D_SD(17)D_SD(16)
D_DQM2
D_nWED_CLKE
D_SA(12)
D_BA1
D_SA(10)
D_SD(28)
D_SD(27)D_SD(26)D_SD(25)D_SD(24)
D_SD(23)D_SD(22)D_SD(21)D_SD(20)
A_ADDR(18)A_ADDR(17)A_ADDR(16)A_ADDR(15)A_ADDR(14)A_ADDR(13)A_ADDR(12)
A_ADDR(3)A_ADDR(2)
A_ADDR(21)
A_ADDR(2:21)
D_SD(31)D_SD(30)D_SD(29)
nRESET
CSSKDI
DO
nSCS0
A_ADDR(11)A_ADDR(10)A_ADDR(9)A_ADDR(8)A_ADDR(7)A_ADDR(6)A_ADDR(5)A_ADDR(4)
A_ADDR(20)A_ADDR(19)
D_DQM3
D_nCAS S_nSCS0
nWE
SDCLK1
ADDR(22) A_ADDR(22)
D_CLKE
SDCLK0
DATA(0:31)
S_DATA(0:7)
A_ADDR(22)
A_ADDR(19)A_ADDR(18)A_ADDR(17)A_ADDR(16)
A_ADDR(20)
A_ADDR(2)
D_SA(6)
D_SA(4)D_SA(3)D_SA(2)
D_SA(11)D_SA(10)
D_SA(1)D_SA(0)
D_nWE
D_nRAS
D_DQM1
D_nCAS
D_CLKESD_CLK0
D_BA1D_BA0
D_SA(9)D_SA(8)D_SA(7)D_SA(6)
D_SA(4)D_SA(3)D_SA(2)
nSCS0
D_DQM0
D_SA(10)
D_SA(1)D_SA(0)
D_nWE
D_nRAS
D_DQM2
SD(24)
nSCS2DQM3
SD(28)SD(29)SD(30)SD(31)
D_SD(0:31)
SD(0:31)
SA(0:12)
SD(11)SD(10)
SD(9)SD(8)
SA(7)SA(5)SA(3)SA(1)
SA(11)SA(9)
SD(15)SD(14)SD(13)SD(12)
nSCS0
SD_CLK0
D_BA1D_BA0
D_SA(9)D_SA(8)D_SA(7)
CLKE
DQM0
D_SA(5)
SA(8)SA(10)SA(12)
BA1
nSCS1
DQM2
DQM1
nCASnRASBA0
SD(27)SD(26)SD(25)
SD(0)SD(1)SD(2)SD(3)
SD(4)SD(5)SD(6)SD(7)
SD(17)SD(16)
SD(18)
SD(21)SD(20)
SD(22)
SD(19)
SD(23)
SA(0)SA(2)SA(4)SA(6)
D_SA(5)
SD_CLK0
CLKE
SDCLK0
CKE
ENG.
1
C
Bingbang Plus
7
MAIN
CONFIDENTIAL
SIGN
B
Page:
(ASIC)
4
ARP.
C.B.LEE
E
Network Interface
’04.09.02
(SPGPM)
* FACTORY OPTION
B
8
DATE
A
B
TITLE:
Rev 1.0
3B
DRW.
B
ED.
D
REV:
F
5
8
CHANGE PART
1
F
D
REVISION RECORD
S.D AN
5
4/16
A3
C.B.LEE
C.B.LEE
CHK:
(SPGPM)
6
Size:
6
7
E
B
(FLASH ROM)
2
2
3
Drawing Number:
SAMSUNG ELECTRONICS
A
ED NO.
1
(SPGPM)
4
C
43
40
28
3
10K
R63
53
100R62
32
44
11
49
14
58
15
DGND
47
100p
F
C30
7
9
48
35
30
C30
6
100p
F
DGND
L19INSTPAR
8
41
1/16W
1 2
3 4
5 6
7
21
RA18 3939RA14
2011-001094
1/16W
1
3
5
7 R6610K
25
16
37
33
DGND
60
23
7
8
39RA16 1/16W
1
3
5
39 R50
7 8
29
1/16W39RA201 2
3 4
5 6
7
5 6
7 8
10KR61
RA4 39 1/16W
1 2
3 4
2
10 R65
10
26
50
51
DGND46
39
1
3
5
7
+3.3V
1/16W
2011-001094
RA10 39
8
6
RA5 39 1/16W
1 2
3 4
5 6
7
59
4
392
4
6
8
1/16W
2011-001094
RA11
39 R51
52
45
13
3
5
7
7 8
1/16W
2011-001094
RA15 391
39RA21 1/16W
2011-001094
1 2
3 4
5 6
12
1
3
5
7
54
39RA13
2011-001094
1/16W
12
34
56
78
1/16W39RA3
C90100pF
+3.3V
57
42
27
CN9-1
3702-001121
1
+3.3V
7 8
RA6
1 2
3 4
5 6
19
1/16W39
55
10 R64
56
DGND
17
24
20
18
5
31
22
34
FX2CA2-60P-1.27DSAL
38
36
A_ADDR(19)ADDR(19)ADDR(20) A_ADDR(20)ADDR(21) A_ADDR(21)
ADDR(14:21)
A_ADDR(14:21)
A_ADDR(14:15)
A_ADDR(7)
IN_3.3
A_ADDR(14)A_ADDR(15)A_ADDR(16)A_ADDR(17)
ADDR(14)ADDR(15)ADDR(16)ADDR(17)
A_ADDR(18)ADDR(18)
A_ADDR(12)
A_ADDR(6)
ADDR(2:13)
ADDR(4)ADDR(3)
A_ADDR(5)A_ADDR(4)A_ADDR(3)
A_ADDR(2)ADDR(2)
ADDR(9)ADDR(8)ADDR(7)ADDR(6)
S_DATA(18)S_DATA(19)
A_ADDR(8)A_ADDR(9)
ADDR(10)A_ADDR(10)ADDR(11)ADDR(12)ADDR(13)A_ADDR(13)
A_ADDR(11)
S_DATA(0:15)
S_DATA(11)
DATA(12)DATA(13)DATA(14)DATA(15)
DATA(9)DATA(10)
DATA(8)
DATA(0:15)
DATA(11)
S_DATA(16)S_DATA(17)
DATA(2)DATA(3)
S_DATA(0) DATA(0)
S_DATA(3)
S_DATA(12)S_DATA(13)S_DATA(14)S_DATA(15)
S_DATA(9)S_DATA(10)
S_DATA(8)
nNPC_INT
S_DATA(4) DATA(4)S_DATA(5) DATA(5)S_DATA(6) DATA(6)S_DATA(7) DATA(7)
S_DATA(1) DATA(1)S_DATA(2)
S_DATA(21) DATA(21)S_DATA(22) DATA(22)S_DATA(23) DATA(23)
S_DATA(16:31)
nNPC_CS
nRD
nWR
nNPC_RST
nWAIT
nPRT_IRQ
S_DATA(31)
S_DATA(28)DATA(29)S_DATA(29)
S_DATA(30) DATA(30)DATA(31)
DATA(18)DATA(17)DATA(16)
S_DATA(20) DATA(20)
ADDR(5)
A_ADDR(15)
DATA(19)
A_ADDR(14)
DATA(24)
S_DATA(27)
S_DATA(24)DATA(25)S_DATA(25)
S_DATA(26) DATA(26)DATA(27)
DATA(28)
SIGN
C
2
C
CHANGE PART
5
CONFIDENTIAL
3B
SAMSUNG ELECTRONICS
3
D+
PANEL & USB
PANEL_1
5 6
DA204K
1
’04.09.02
CHK:
FGND
Page:
C.B.LEE
AGND
S.D AN
ED.
82
A
D-
DATE
4
REVISION RECORD
A
[USB_CONN]
ARP.
B
D
E
B
6
1
F
E
FGND
RESERVED
8
B
REV:
DRW.
Bingbang Plus
D
cf) 2.2uF,2012, 2203-001598
71B
5/16
A3
C.B.LEE
C.B.LEE
F
4B
7
MAINRev 1.0
Drawing Number:
Size:
ENG.
ED NO.
VBUS
TITLE:
1nF
C3
R220
DGND
47K
3
1
2 3
4
OSC4
HC-49(30MHz,50ppm)
2801-003582
INSTPAR
L15
100nF
C277
C15
1nF
C273
100nF
AGND_USB
3301-001258|R1608_BEAD
L6B600
2.2uF
C267
USB_3.3VA
2
DGND
INSTPAR
L12
3301-000325
100nF
C271
R346
2203-000476|R2012_CAP
C234
10K
B600 L4
1uF
R345 9.09K,1%
DGND
5
2
787780-1CN2-1
3722-001101
1ND2
1
3
20K NR11
USB_3.3V
19VSSIO0VSSIO1
2429
VSSIO2
XIN11
12XOUT
+3.3V42
VDDC1
17VDDIO0VDDIO1
32
VSS05460
VSS1VSS2
63
VSSC0941
VSSC1
RSDP55
3SMC
TEST11
TEST22
TEST364
48VBUS
57VDD
VDDC010
23LD7LD8
2526
LD9
PVDD62
PVSS61
53RPU
RREF49
59RSDM
31LD13LD14
33
LD1534
LD21618
LD3LD4
2021
LD5LD6
22
5LA3LA4
4
LCLKO35
LD01415
LD1
LD102728
LD11LD12
30
DACK38
DM5856
DP
DREQ37
39EOT
LA087
LA1LA2
6
*IOR4445
*IOW
47*IRQ
*RESET43
ALE40
AVDD51
AVSS05052
AVSS1
0904-001752
NET2270
U27
*CS46
*DMARD3613
*DMAWR
NR12
USB_3.3V
AGND_USB
0
R348
0
4
DGND
DGND
35.7,1%
R343
10pFC266
100nF
USB_3.3VA
C274
2703-000300|R1608_BEAD
LK16081ROK-T
L30
1uH
RA48
10K
1357
AGND_USB
0407-000101
ND1
1
3
2
USB_3.3V
63mW
C272
100nF
1 2
3 4
5 6
7 8
+3.3V
RA47 39
R351100
B600 L28
DGND
DGND
AGND
1uHL31
C276
100nF
DGND
AGND_USB
R342 35.7,1%
6
2.2uF
C239
10pFC265
3301-000325|R3225_BEAD
CIB32P600NES
L29
STS104BF9
2
1 3
DGND
2901-001178
100nF
C275
R350
USB_3.3V
3
0
C268
2.2uF
100nF
C1
DGND
1nF
DGND
C278
C2
1nF
2.2uF
C270
DGND
NR130
42ohm
L18
USB_3.3VA
C269
2.2uF
5
3301-000325|R3225_BEAD
L2
42ohm
1
35303-0550CN4-1
1.5KR344
2
R216 39
4
+5V
DGND
R349 0
VBUS_2270
VBUS_2270
PANEL_RX
USB_3.3V
S_DATA(31)S_DATA(30)S_DATA(29)S_DATA(28)S_DATA(27)S_DATA(26)S_DATA(25)S_DATA(24)S_DATA(23)S_DATA(22)S_DATA(21)S_DATA(20)S_DATA(19)S_DATA(18)S_DATA(17)S_DATA(16)
DP
DN
nUSB_DACK
USB_XOUT
USB_XOUT
USB_XIN
ADDR(5)ADDR(4)ADDR(3)ADDR(2)
ADDR(6)
S_DATA(16:31)
VBUS
nRD
PANEL_TX
nRST_PANEL
$P
nUSB_IRQ
nUSB_RST
nUSB_REQUSB_XIN
ADDR(2:6)
nUSB_CSnWR
B5
N.C
DATE
B
A
7
nINIT
nSELECTIN
nFAULT
2
DATA3
DATA7
D
A
4
nACK
6
CONFIDENTIAL
C
ENG.
REV:
DATA2
3
8
CLP-511/511G ONLY
Drawing Number:
DATA6
C.B.LEE
nAUTOFD
5
SELECT
B
6
DATA1
TITLE:
Page:
ARP.
DATA4
REVISION RECORD
DATA5
C
P 1284
F
BUSY
D
B
MAIN
S.D AN
2
1
7
CHANGE PART
PERROR
’04.09.02
B
1
Rev 1.0
3
6/16
A3
C.B.LEE
C.B.LEE
Size:
8
SIGNSAMSUNG ELECTRONICS
B
EE
4
DRW.
(CENT36)
ED.
nSTB
ED NO.
Bingbang Plus
F
DATA0
1
CHK:
Data23
0401-000116|R3616_DIO
MMSD914T1
D30
VCC2 1831VCC_C142VCC_C2
Y10 4645Y11
Y12 4443Y13
47Y9
GND33439 GND4
1HD
24 HLH HLHin 2530PLHPLHin19
7VCC1
B8 32
C4 2928C5
C6 2726C7
DIR 48
GND11015 GND2
2 A9
41B1B2 40
38B3B4 37
36B5B6 35
33B7
23 A17
A2911 A3
A41213 A5
A61416 A7
A817
8 A1
A1034 A11
A1256 A13
A142021 A15
A1622
21
74LVX161284MTD
U7
1006-001224
DGND
GND
DGND
DGND14
22
5V1
nAutoFd
GND
L16
2GND
IN
1
OUT
3
+5V
DGND
DGND
F2
STS104B
GND20
LCTL4036E09
19GND
12
11PError
R1610K
Busy
36
31
nSelectIn
33
nInit
SEN_5V
AGND
nAck10
6
DGND
INSTPAR
L5
VC
C
+3.3V
DGND
DGND
Data5
P1
P2
12
P3
10 8P
4
P5
2 1P
6
P7
28 27P
8
20
B3
B423
21B5
B619
18B7
B817
16B9
GN
D22
15
6
A57
9A6
A711
13A8
A914
26B1
B225
24
HIC1
SUPER1284
2011-001334
3A1
A24
5A3
A4
18
GND27
29GND
L3
0501-000457
13
2
R33
5.1K
4
MMBT2222ALT1
Q1
30
Data3
23
GND
GND
DGND
R31
5.1K
7Data6
3
21K
R22MMBT2222ALT1
Q16
1
C13
100nF
100nF
C29
25
DGND
GND
10KR225
GND24
13
34
9
Select
32
Data8
100nF
C12
nFault
Data12
C32
100nF
5Data4
100nF
C36
+3.3V
NL2
LED5
SLS-NNGR202TS
0601-001444
5V1
AGND
SEN_5V
5V1
nStrobe
CN3-1
3702-000118
35
R182
100nF
510
L1
C46
15
28
Chassis GND17
SEN_5V
8
DGND
GND
Data7
NL1
3301-000325|R3225_BEAD
26
16
GND
TEST_LED1
PD(0:7)
nFAULTSLCT_OUT
PERROR
nSELECTINnINIT
nSTROBE
BUSYnACK
nAUTOFD
PDE
PD(0)PD(1)PD(2)PD(3)PD(4)PD(5)PD(6)PD(7)
0.1
C
B
D
NC
DRW.
F
A
ED NO.
ENG.
Y.S EOM
1
1
SIGN
REV:
E
SAMSUNG ELECTRONICS
CHANGE PART
TITLE:
D
5
2
CHK:
ARP.
4
6
Page:
C
S.D AN
1
B
3 8
REVISION RECORD
B7
2
Y.S EOM
B
B
Y.S EOM Bingbang Plus
8
Size:
3 5
CONFIDENTIAL
A
4
Rev 1.0
F
6
* Not used
ED.
7
B
ASIC
DATE
E
NC
Drawing Number: 7/16
A3
’04.09.02
MAIN
4 6 8
+3.3V
RA3610K
63mW
2R33910K
1nF
R282
C242
10K
10K
R318
DGND
DGND
R32
210
K
+3.3V
10K
R32
3
NC4
10pF
R28010K
10K
R308
100nF
C130
R317
10K
R306
10K
680NR10
100nF
C120
+3.3V
DGND
DGND
+3.3V_LPEC
R135 39
63mW
2 4 6 8
+3.3V_LPEC
RA3410K
10K
R307
39R123
100nF
C121
+3.3V
C141
100nF
+3.3V
RA45
2 4 6 8
63mW
10K
6 8
63mW
10KRA43
2 4
100nF
DGND
C135
100nF
C152
16V100uFC155
39R103
Y_V
SS
O1
21Y
_VS
SO
383
117Y_VSSO4
Y_VSSO_254
110Y_VDDI4
Y_V
DD
O1
38
Y_VDDO261
Y_V
DD
O3
976
Y_V
SS
I1
Y_V
SS
I229
Y_V
SS
I382
Y_VSSI4104
VD
DA
73
VD
O_L
SU
_N_O
UT
7
45VD_IN
WE
_N_I
N37
125Y_VDD4
Y_V
DD
I113
46Y_VDDI2
Y_V
DD
I389
43MCLK_IN
OE_N_IN 39
36P
SY
NC
_N_O
UT
41RESET_N_INSCAN_EN_IN
42
SCAN_MODE_IN44
8S
H_L
SU
_N_O
UT
2S
TA
RT
_LS
U_N
_OU
T
GP
IO9_
2/M
OT
2_B
34
GP
IO9_
3/M
OT
2_nB
3510G
PIO
A_1
/SIO
_TX
DG
PIO
A_2
/SIO
_RX
D11 12
GP
IOA
_3
GP
IOA
_O/S
IO_C
LK94
HS
YN
C_N
_IN
LDO
N_L
SU
_N_O
UT
5 25G
PIO
8_2/
MO
T0_
BG
PIO
8_3/
MO
T0_
nB26 27
GP
IO8_
4/M
OT
1_A
GP
IO8_
5/M
OT
1_nA
28
GP
IO8_
6/M
OT
1_B
30 31G
PIO
8_7/
MO
T1_
nBG
PIO
9_0/
MO
T2_
A32 33
GP
IO9_
1/M
OT
2_nA
76G
PIO
6_4/
PW
M4
GP
IO6_
5/P
WM
57778
GP
IO6_
6/P
WM
6G
PIO
6_7/
PW
M7
7980G
PIO
7_0/
PW
M8
GP
IO7_
1/P
WM
981
23G
PIO
8_0/
MO
T0_
AG
PIO
8_1/
MO
T0_
nA24
GPIO5_3/EXT_CON3124
GPIO5_4126127
GPIO5_5GPIO5_6
128
GP
IO6_
0/P
WM
06566
GP
IO6_
1/P
WM
1G
PIO
6_2/
PW
M2
6768G
PIO
6_3/
PW
M3
GPIO4_4116
GPIO4_5118119
GPIO4_6GPIO4_7
120
GP
IO57
1
121GPIO5_0/EXT_CON0GPIO5_1/EXT_CON1
122123
GPIO5_2/EXT_CON2
107GPIO3_4GPIO3_5
108109
GPIO3_6
111GPIO3_7GPIO4_0
112113
GPIO4_1GPIO4_2
114115
GPIO4_3
98G
PIO
2_4
GP
IO2_
59910
0G
PIO
2_6
GP
IO2_
710
110
2G
PIO
3_0
103GPIO3_1
105GPIO3_2GPIO3_3
106
88G
PIO
1_4
GP
IO1_
590
GP
IO1_
69192
GP
IO1_
7G
PIO
2_0
9394G
PIO
2_1
GP
IO2_
29596
GP
IO2_
3
18G
PIO
0_4
GP
IO0_
519 20
GP
IO0_
6
GP
IO0_
722
84G
PIO
1_0
GP
IO1_
18586
GP
IO1_
2G
PIO
1_3
87
CPU_DATA756
CS_N_IN 40
74D
A_O
UT
GN
DA
75
14G
PIO
0_0
GP
IO0_
115 16
GP
IO0_
2G
PIO
0_3
17
47CPU_ADDR7_IN
CPU_DATA06463
CPU_DATA1CPU_DATA2
62
CPU_DATA360
59CPU_DATA4CPU_DATA5
5857
CPU_DATA6
CLK
_LS
U_O
UT
3
CPU_ADDR0_IN55
53CPU_ADDR1_INCPU_ADDR2_IN 52
51CPU_ADDR3_INCPU_ADDR4_IN
5049
CPU_ADDR5_INCPU_ADDR6_IN
48
AD
0_IN
6970A
D1_
INA
D2_
IN7172
AD
3_IN
+3.3VA
JC13-00020A
LPEC1U17
+3.3V
GNDA
10K
R281
+3.3V
2 4 6 8
RA4210K
63mW
8
RA38
2 4 6
10K
2 4 6 8
63mW
10K
6 8
RA41
63mW
10KRA39
2 4
63mW
2 4 6 8
RA4610K
63mW
R34010K
C149
100nF
C128
100pF
C127
100nF
10KRA33
2 4 6 8
63mWR298
10K
+3.3V
R134 39
GNDA
470p
FC
281
C151
R163
100nF
10K
R30
5
10K
100R117
R132
10K
DGND
C156
100nF
F8
STS104B
2
1 3
10K
R299
CLK_SCFCMD_SCFSTS_SCF
nCS_LPEC
BLDC_CLK1PWM_DEVEPWM_CHARGE
nSH_LSU
PWM_T1PWM_T2PWM_ACPWM_AC_VPP
BLDC_CLK2
CRUM_SEL1CRUM_SEL0
nVDO_LSU
nVDI_LPEC
ITB_SCL_OUT
ITB_SDA_OUT
5VL_DETECT
DEVE_SCL_OUT
A_OPC_KEY
nCUT_OPC
DEVE_SDA_INDEVE_SDA_OUT
ITB_SDA_IN
nT_COVER_OPEN
ENB_DEVE_ACENB_T2
nPSYNC
nWR
AN_MUX2
AN_FUSER1_OUT
DATA(3)
DATA(2)DATA(1)DATA(0)
A_ADDR(9)A_ADDR(8)A_ADDR(7)A_ADDR(6)A_ADDR(5)A_ADDR(4)A_ADDR(3)
nS_TONER_RX
nCLT_DEV_3RDnCLT_DEV_2NDnCLT_DEV_1ST
DATA(7)DATA(6)DATA(5)DATA(4)
nFAN_FUSERADC2ADC1ADC0
nSOL_DEV_4THnSOL_DEV_3RDnSOL_DEV_2NDnSOL_DEV_1ST
nCLT_DEV_4TH
nEN_CTD_LED
nS_MP_EMPTnS_EMPT
nS_EXIT
nS_FEEDnBLDC_START2nBLDC_START1
nBLDC_RDY1nBLDC_RDY2
nSOL_PICKUPnSOL_MP
nCLT_FEED
nSOL_T2nSOL_DUP
nHEATERnSOL_ITB_CLN
VCLK
nLDON_LSU
nHSYNC
nPTL_LED
RDY_SCF
nS_ITB_HOMEnRDY_LSU
CLK_LSU
DATA(0:7)
A_ADDR(2:9)
nWST_AGT
A_ADDR(2)
nSTART_LSU
nRESET
nRD
2
Y.S EOM
ED NO. CHANGE PART
6
B
S.D AN
1
DRW.
7
8
5
B
CONFIDENTIAL
BUFFER & LSU
F
SAMSUNG ELECTRONICS
MICRO
1
DATE
4
B
B
0.1
B
Drawing Number:
2005-001058
Size:
A
REVISION RECORD
7
DA204K
C
ED.
B
CHK:
A3
Y.S EOM
Y.S EOM
8
SWITCH
2
ENG.
4
E
SIGN
3
3
F
5
REV:
6
TITLE:
1
D D
A
C
ARP.
Page:
Bingbang Plus
’04.09.02
MAINRev 1.0
E
LSU
LSU
12
8/16
R2905.6K
DGND
U22-2DM7407MX
34
DGND
+5V
DGND
100R244
100R243
6
+3.3V
R164
100nFC163
+3.3V
10K
+3.3V
+5V
C232
13 12
10nF
4GND
NC13
NC25
6NC3
1VCC
0803-001393
DM7407MX
U22-6
1006-001250
U12
DS90LV017ATMX
2DI1DO1+
7
8DO1-
C284
DGND
C255
0.068nF
100nF
4
1nFC207
DGND
LM393D
1202-000164
U24-2
5
6
7
1
+5V
R241
3711-002813
CN12-135303-1250
100
DGND
DM7407MXU22-5
1110
DGND
10KR291
+5V
56
U22-3DM7407MX
1K
DGND
DGND
R156
5
NC23133pF
DGND
16V470uF
C99
C238100nF
R14210K
9
+5V
R2261K
100nF
C110
R289
10K
3.3K
DM7407MXU22-4
9 8
R151
11
C86
100nF
3W
0.39
R82
10K
100
R242
10
R287
DGND
DGND
C29610nF
100nF
C71
+3.3V
0407-000101
D321
3
2
AGND
C2971nF
2
2
+24V
R166100
R2883.3K
7
1
14
2
DM7407MX
U22-1
+5V
+5V
7
DGND
10K
R157
L37B600
+5V
+5VL
10K
R150
DGND
8
+3.3V
100R257
3
AGND
10K
DGND
R147
+5VL
0.068nF
C256
1
35303-0250
3711-003408
CN14-1
C30
810
0nF
DGND
100uF
C68
C15710nF
L34
50V
INSTPAR
5VL_DETECT
+5V
nLDON_LSU
nSH_LSU
CLK_LSU
nSTART_LSU
nVDO_LSU
nRDY_LSU
nHSYNC
OEM_CONN
ED.
Bingbang Plus
B2
A
1 8
ARP.
Y.S EOM
E
6
DATE
ENG.
B
4
SMPS
Drawing Number:
B
2
Size:
REVISION RECORD
C
HVPS
D
3
C
E
CONFIDENTIAL
ED NO.
DA204K
8
Y.S EOM
Y.S EOM
Power TestPoint
TITLE:
SMPS & HVPS
CHK:
D
REV:
F
B
SAMSUNG ELECTRONICS
B
DRW.
F
6
Page:
1
4
3
5
5 7
1
SIGN
B
S.D AN
A
7
’04.09.02
MAINRev 1.0
CHANGE PART
5 6
9/16
A3
DM7407MXU18-3
R253100
22
3_3VA1
+24VF
98
5VL1
DGND
DGND
DM7407MX
U8-4
4
+5VL
100nF
C177
24
DGND5
+5V
DGND
+5V
3
100nF
C285C291
100nF
+24VF
13
7
100nF
C166
D23
0407-000101
1
3
2
9 8
DGND3
0803-001393
U18-4DM7407MX
1.8V+3.3V
DGND
15
100nF
C144
U8-3DM7407MX
56
+3.3VA
2
AGND1
D36
1
3
2
100nF
C182
GNDA1
12
100nF
C286
DGND1
R254100
3711-002003
26
12
DGND
1110
GNDA3
U8-5DM7407MX
2
9
11
C175
100uF50V
C2521nF
U18-2
DM7407MX34
18
8
21
+24VF
19
25
3
4
9
+24VF
DGND
C176
470uF16V
24VF1DGND
100nF
C292
13
8+24V
11
34DM7407MX
U21-2
DGND
DGND
5
6
+3.3V
+5V
3
GNDA
GNDA2
14
10
AGND2
2
1nFC251
15K
R195
4
7
1
14
2
R196
+24V
DM7407MXU8-1
DGND
DGND
DGND
100K
100
100 R251
1_8V1
R248
5V1
6
11 10
23
DGND
DM7407MXU18-5
L41B600
7
AGND
+5V
20
18
DGND4
C311 1nF
CN37-135303-0850
1
AGND
16
DGND
+5VL
C57100nF
U18-1
DM7407MX
7
1
14
2
R249100
6
34
AGND
0803-001393
U8-2DM7407MX
+5VL
GNDA
8
C169
DGND2
DGND
100nF
3_3V1
C282
330pF
5
AGND
15
DGND
C171
470uF16V
24V1
CN7-1
DF11-18DP-2DSA(18)
1
+24VF
AGND
10
C2431nF
CN30-1DF11-26DP-2DSA(22)
1
17
DGND
1nF
C31
8
C317 1nF
+3.3VA
+3.3V
1nFC312
B600 L40
L39B600
AGND
B600 L38
3301-001258
16
DGND
17
14
100 R246
DM7407MX
U8-6
1312
10nF
C197
12
7
DM7407MXU18-6
0803-001393
13
5
A_READ_CHA
A_WST_AGT
DEVE_CRUM_SDA
DEVE_CRUM_SCL
A_READ_T1
A_READ_T2
nT_COVER_OPEN
nFUSERON
nWST_AGT
ENB_T2
PWM_AC
PWM_AC_VPP
PWM_T2
PWM_CHARGE
PWM_T1
ENB_DEVE_AC
PWM_DEVE
Page:
3
Drawing Number:
S.D AN
3
F
Y.S EOM
B
REVISION RECORD
B
0402-001189
B
E
SIGN
C
ED NO.
4
1
7
C
4
E
DRW.
SAMSUNG ELECTRONICS
1
5
ENG.
2 8
A
7
DATE
B
10/16
A3
Y.S EOM
Y.S EOM
B
D
CHANGE PART
F Size:
REV:
’04.09.02
MAINRev 1.0
MOTOR
FUSER FAN
A
D
1
6
6
8
TITLE:
CONFIDENTIAL
ARP.
CHK: Bingbang Plus
ED.
B
5
BLDC1
2
DGND
R200
DGND
DGND
7
10K
DGND
74LCX06M
U26-4
0803-003264
9 8
2
+5V
D28M4
C209100nF
AGND
3
2
DGND
510
R277
AGND
0501-000457
Q13
MMBT2222ALT1
1
DGND
R183
510
AGND
+5V
R1815.1K
C30
91n
F
1nF
C230
100
R192
10nFC174
CN29-135303-0350
1
C287
100nF
1.2K
R171
34
6
+24VF
3
0803-003264
U25-274LCX06M
R201
10K
10
100
R255
R199
10K
+5V
+5V
3
8
DGND
5
9
1
2
0803-001393
98
3711-002811
CN27-135303-1050
DM7407MXU21-4
R180
R1795.1K
510
Q11MMBT2222ALT1
13
2
+24VF
C295
0501-000457
4
AGND100nF
DGND
nBLDC_RDY1
nFAN_FUSER_ON
nFAN_FUSER
BLDC_CLK1
nBLDC_START1
TITLE:
8
WASTE_TONER & EXIT
E
3
A
MAIN
6
C
B
ED NO.
ED.
F
Y.S EOM
B
CHANGE PART
SAMSUNG ELECTRONICS
1SENSER
SIGN
DATE
E
1 4
75
C
Size:
DA204K
REVISION RECORD
2
ARP. S.D AN
1
B
5
DA204K
FEED
6
D
4
EMPT
Page:Drawing Number:
11/16
A3
Y.S EOM
Y.S EOM
A
D
CONFIDENTIAL
B
MP_EMPT
7
DRW.
REV:
B
Bingbang Plus
8
CHK:
B
’04.09.02
ENG.
F
2
Rev 0.21
3
C183
10nF
100
R120
R205
100
7
1/4W
39
R111
DGND
6
C150
10nFDGND
3711-003409
3
10nF
DGND
43
C179
1
+3.3V
DGNDDGND
3711-000225
5045-04ACN31-1
1
3
2
47KR145
100nF
0407-000101
D16+3.3V
C288
R104
15K
3
3
R203
100
100
R101
+3.3V
2
10nF
DGND47K
C125
R204
2
+3.3V
4
C133
10nF
2
DGND
3711-003410
4
CN33-1
1
DGND
D25
1
3
235303-0350
5
DGND
0407-000101
47KR113
DGND
1
+3.3V
CN17-1
35303-0750
100
R140
DGND
C290
100nF
DGND
+3.3V
DGND
100nF
C289
+3.3V
DGND
CN21-135303-0450
1
2
47KR202
nS_EMPTnS_MP_EMPT
nS_FEED
nS_EXIT
nS_TONER_RX
SAMSUNG ELECTRONICS
7B
B
5
0402-001189
REV:
CLT_FEED
F
E
ED.
E
A
Bingbang Plus
’04.09.02
MAINRev 1.0
1
C
REVISION RECORD
F
DATE
Page:
CHK:
T2_HOME
0402-001189
D
8
C
81
MP_SOL
6
4
S.D AN
4
B
DUPLEX
SIGN
SOLENOID
ED NO.
0402-001189
5
ENG.
A
DRW.
B
0402-001189
Drawing Number:
3
TITLE:
Y.S EOM
Size:
CONFIDENTIAL
3
ARP.
B
0402-001189
CHANGE PART
D
AGND
12/16
A3
Y.S EOM
Y.S EOM
2
1 72
PICKUP_SOL
B6
DGND
CN32-15045-03A
1
AGND
510
R144
5.6KR189
KSD1691-Y
Q8
0502-001048
32
1
1
2
35303-0250CN23-1
+5V
C213100nF
100nFC154
AGND
MMBT2222ALT1Q15
13
2
R184
0501-000457
2
510
3711-000164
2 DGND
74LCX06M
U25-5
0803-003264
12
510R168
100nF
C165
DGND
C161100nF
U26-6
74LCX06M
1312
+24VF
AGND
DGND
+24VF
AGND
0803-003264
C214
C173100nF
+5V
100nF
C167100nF
5045-03ACN26-1
1
M4D21
AGND
+5V
100nFC178
DGND
3
1
R190100
2
KSC1008-Y
Q9
0501-000010
2
AGND
C170100nF
AGND
C215100nF
1312
AGND
DGND
AGND
+24VFAGND
+5V
74LCX06M
U25-6
0803-003264
AGND
D20M4
100nFC212
510
R146
R1525.6K
D27M4
5.6K3711-000198
3
R186
R138
1K
0803-003264
U26-5
74LCX06M
12
100nFC184
C211100nF
R191
C153100nF
510
3711-000198
3
0402-001189|R5226_DIO
M4D24
R139
DGND
3711-003408
2
AGND
AGND
5.6K
0501-000457
13
2
7
11
14
10
Q12MMBT2222ALT1
74LCX06M
U25-1
0803-003264
C172100nF
R185
C158100nF
100
1
5.6KR173
CN24-15045-02A
1
AGND
5045-02ACN25-1
+5V
+3.3V
+24VF
R169100
D29M4
R153
3
1
+24VF
100
nSOL_PICKUP
0501-000010
Q7
KSC1008-Y
2
nSOL_T2
nSOL_MP
nSOL_DUP
nCLT_FEED
E
CHK: Y.S EOM
TH1
CONFIDENTIAL
ANALOG
2007-008567
DRW.
B
ARP.
5
8
’04.09.02
MAIN
7
A
ED NO.
E
2007-000066
SAMSUNG ELECTRONICS
S.D AN
D
ITB
BB
6
Drawing Number:
A
B4
2007-000736
3
C
1%
SIGN
ENG.
ED.
1 2
TITLE:
CHANGE PART
3
1
DA204K
D
2007-000842
Page:
Bingbang Plus
Size:
8
Rev 1.0
DA204K
2
F
REV:
5
B
REVISION RECORD
4
B
TO FUSER ROLL
F
6
DATE
1
7
C
1
3
2
13/16
A3
Y.S EOM
Y.S EOM
35303-0250
1
0407-000101
D153K,1%CN28-1
C168
GNDA
R187
L9
1nF
D22
MMSD914T1
INSTPAR3301-001258
3
2
8
4
1
1K
U24-1
1202-000164
LM393D
R178
C160100nF
GNDA
GNDA
4
3
6
+3.3VA
100nF
R834.7K
DGND
GNDA
+3.3VAC108
U25-374LCX06M
0803-003264
56
R266 33K
2
CN10-135303-0750
1
100uF16V
A
100
R84
DGND
C263
2
+3.3V+3.3VR174
20K,1/16W
30K
R198
30K,1%
R193
DGND
GNDA5.6K
R170
C264100nF
4.7K
R17768
L21
INSTPARL20
+5VL
3301-001240|R1608_BEAD
INSTPAR
15.4K,1%
+3.3VA
+3.3VA
R175
23
1
10nFC180
7
Q14
0501-000010
KSC1008-Y
0501-000457
13
2
GNDA
4.7K
Q10MMBT2222ALT1
5
R176
2
DGND0407-000101
D9 1
3
3301-001258INSTPAR
L23
ITB_CRUM_SCL
ITB_CRUM_SDA
AN_FUSER1_OUT
nS_ITB_HOME
nFUSERON
nHEATER
F
ENG.
S.D AN
CHANGE PART
CHK:
DRW.
REVISION RECORD
TO TEMP BD
Page:
A
1 4
3
5
TITLE:
B6
Size:
7
SIGN
MAIN
* Not used
CONFIDENTIAL
ED NO.
E
B
2
OPC KEY
4
Rev 1.0Y.S EOM
Y.S EOM
7
B
5
1ED.
2
B
Y.S EOM Bingbang Plus
’04.09.02
8
TH4
DATE
C
F
REV:
SAMSUNG ELECTRONICS
B
A
E
ANALOG MUX3
TH3
1
B8
ARP.
6
PTL & TH4
Drawing Number:
14/16
A3
L36
L35B600
B6002
C111
100nF
3711-003408INSTPARL22
35303-0250CN15-1
1
+3.3VAMMSD914T1
D33
R341
AMMSD914T1
D34
0
GNDA
+3.3VA
3
1.2KR314
150 1/4W
R228
2001-000111|res_p400
0404-000112
D42RB420D T147
+5V
R75510
DGND
R695.1K
C100
100nF
35303-0450
CN11-1 1
DGND
10nF
C14
0
GNDA
13
2
+5V
MMBT2222ALT1
Q3
0501-000457
0803-003264
34
74LCX06M
U26-2
AMMSD914T1
D35
3K,1%R284
100nFC117
2
GNDA
NR155.6K
NR145.6K
47K
R99
47K
,1%
3301-000325
L10INSTPAR
+3.3VA
3K,1%R933K
KSA708_YNQ12
3
1
+3.3VA
+3.3VA
DM7407MX
U21-3
5 6
+3.3VA
35303-0250
CN6-1
1 M4ND3
GNDA
16V100uFC119
47K
R26
747
K,1
%
B1 INSTPAR
10nF
C13
4
100nF
C237
STS104BF7
2
1 3
4
GNDA
$P
$P
R129 100K
100nF
C148
R121 100K
39R332
C114
100nF
DGND
100nF
C23
1
10nF
C14
7
+5V
GNDA
5 X5
X62
4 X7
INH 6
VC
C
16
3XX013
14 X1
X215
12 X3
X41
1001-000170
U20MC14051BD
11A
B 10
9C
GN
D
8
GN
D
7
+3.3VA
3711-003408
2
100KR114
nPTL_LED
A_TEMP2
A_OPC_KEY
A_READ_CHAA_READ_T2A_READ_T1
A_TEMP
+24VF +24VF
AN_MUX2
AN_WST_AGT
A_TEMP
A_TEMP2
A_OPC_KEY A_OPC_KEY
nCUT_OPC
ADC0
ADC1
ADC2
AN_READ_CHA
AN_READ_T2
AN_READ_T1
AN_READ_T1AN_READ_T2AN_READ_CHA
nS_TONER_RX
A_WST_AGT
AN_WST_AGT
5
Page:
DRW.
CONFIDENTIAL
DA204K
F
E
B
Bingbang Plus
DA204K
Drawing Number:
2
MAIN
4
Rev 1.0
SAMSUNG ELECTRONICS
F
6
E
7 8
A
CHANGE PART
1
5
SCF
CHK:
C
4B
SCF, CRUM Interface
B
Y.S EOM
DA204K
7
DA204K
B
6
S.D AN
REVISION RECORD
B
1
ENG.
8
ARP.
ED NO.
2
B
15/16
A3
Y.S EOM
Y.S EOM
1
SIGN
3
DATEED.
3
Size:TITLE:
REV:
A
’04.09.02
DA204K
D11
1
3
2
+5V
C142
100pF
DGND
+3.3V
C2451nF
R126
10K
+3.3V
100R260
+5VL
DGND
1
3
2
C2461nF
L26INSTPAR
D44R296
10K
+3.3V
+5VL
3301-001240|R1608_BEAD
DGND
INSTPARL27
3301-001240|R1608_BEAD
D43
1
3
2
INSTPARL24
3301-001240|R1608_BEAD
INSTPAR
C240100uF
16V
3301-001240|R1608_BEAD
L25
R167
74LCX07MU28-5
1110
DGND
+3.3V
1K
D45
1
3
2
DGND
6
R302
1K
R304
10K
DGND
7
1
14
2
DGND
U28-174LCX07M
100nFC159
R258
4
DGND
100
DGND
DGND
U28-274LCX07M
3
74LCX07MU23-6
13 12
+5V
DGND
C116
100uF50V
100nF
C293
R303
DGND
10K
7
D10
1
3
2
5
CN16-135303-0850
1
3711-002809
8
10
C248100nF
U23-574LCX07M
11
DGND
100pF
C138
U23-174LCX07M
7
1
14
2
100nF
D13
1
3
2
C164
4
DGND
DGND AGND
2
3
1K
R127
DGND
R136
1K
C137
100pF
74LCX07MU23-3
56
100pF
C143
DGND
U23-274LCX07M
34
R14310K
1nFC244
+5V
8
D140407-000101
1
3
2
D46
1
3
2
74LCX07MU23-4
0803-003263
9
+5V
R259100
+24V
10K
R137
+5V
DGND
R261100
1nFC247
DM7407MXU21-1
7
1
14
2 ITB_CRUM_SCL
ITB_CRUM_SDA
DEVE_SCL_OUT DEVE_CRUM_SCL
DEVE_SDA_IN DEVE_CRUM_SDA
DEVE_SDA_OUT
ITB_SDA_IN
ITB_SDA_OUT
ITB_SCL_OUT
STS_SCF
RDY_SCF
CMD_SCF
CLK_SCF
D
F
ED.
B
4
2
ARP.
1
Rev 1.0
DEVE DRIVER
53
Page:
5
Y.S EOM
A
C
2
DATE
DRW.
E
Drawing Number:
A
CONFIDENTIAL
B
BLDC2 SOL_ITB_CLN
4
Size:
E
’04.09.02
7
CHANGE PART
A3
Y.S EOM
Y.S EOM
1
8
6
1
ED NO.
BB
CHK:
MAIN
C
ENG.
6
REV:
S.D AN
D
REVISION RECORD
8
B
0402-001189
TITLE:
B
F
SAMSUNG ELECTRONICS
3
Bingbang Plus
7
DEVE DRIVER
SIGN
3
16/16
11
1nF
C319
DGND
100pF
DGND
100pF
C304 C305
100pF
C302 C303
100pF100pF
C301
100pF
C299 C300
100pF
DGND
C298
100pF
C320 C321
10nF
+24VF
10nF
98
DGND
74LCX07MU28-4
D48
M4
10
74LCX06M
U26-10803-0032647
11
14
AGND
DGND
C283
100nF
+5V
DM7407MXU19-2
3 4
AGND
5.1K
R33
7
2
100nFC260
$P
10nF
C226
4
DGND
100nF
$P
74LCX06M
U26-3
0803-003264
5
6
C257
+5V
DGND
100nF
C294
510R335
1
$P
CN38-135303-0950
1
4
CN5-1
GF102-12S-TS-NF-S
109
6
AGND
C227
1nF
5
C225
10nF
C216100nF
2
100nFC258
1110
0803-003264
U25-474LCX06M
9 8
U21-5DM7407MX
10KR319
R329100
12
R330
DGNDAGND
100
DGND
+24VF
10K
+5V+24VF
R32110K
R320
7
AGND
5.6KR336
10nF
C218
10nF
C220
5045-03ACN35-3
3
C219
10nF
8
+3.3V
5 6
2
U28-374LCX07M
7
DGND
+5V
DM7407MXU19-4
9 8
$P
13 12
1
74LCX07MU28-6
1312
AGND
AGND
DM7407MXU19-6
5
C145100nF
1K
DGND
$P
1110
DGND
R338
510
DM7407MXU19-5
$P6 R334
Q20
MMBT2222ALT1
13
2
DGND
DGND
DGND DGND
R333
10nFC261
510
10nF 1nF
C228C221
U19-3DM7407MX
5 6
100nF
+5V
DGND
C259
DGND
3
1nFC262
23
1
$P
8
Q19
KSC1008-Y
U21-6DM7407MX
1312
$P
$P9
DM7407MX
7
1
14
2
DGND
U19-1
nSOL_ITB_CLN
nSOL_DEV_1ST
nCLT_DEV_1ST
nCLT_DEV_3RD
nCLT_DEV_2ND
nCLT_DEV_4TH
nSOL_DEV_3RD
nSOL_DEV_2ND
nSOL_DEV_4TH
nBLDC_RDY2
nBLDC_START2
BLDC_CLK2
D
SAMSUNG ELECTRONICS CO., LTD.
EF
27
8
ABC
34
56
ALL RIGHTS RESERVED
ABC
1
CR
UM
_DE
VE
CR
U_IT
B
A
SAMSUNG ELECTRONICS CO., LTD.
A
23
45
6
BC
ALL RIGHTS RESERVED7
81
BCEF D
YW396
CON1
21
PIN
CON2
5096-02C
Q2BTA12-600B
BD1600V5A
R71/4W1KJ
C8104K
R61W22J
D4
Q4
50
0V
24
A
D54148
R25220J
R24220J
CS 8
CT
7
RT
1
FB
2
GN
D4
OUT5
IS3
VC
C6
U1 KA7553
R51W180J
0
0
00
PC1S21ME4
+2
4V
VF
C3102
C2102
C5224
C4224
C1474
C13222J
R16100J
R3622J
R1922J
R21 PC3-1 R188.2KJ
C15104K
PC2-1
Q1
BT
A1
2-6
00
B
C7
10
4K
R58
1W
1.5
KJ
R21W47J
C6630V103K
D1200V1A
D21KV1A
C12
50
V4
7u
F
ZD427V
C22
R411KJ
+24VF
3.5A
GND
+3.3V3.5A
D13200V20A
PC3-2
Q6C1008
D114148
R50220J
PC2-2
R514.7KJ
R4910KJ
R1510KJ
R54220J
R39220J
R57680J
GND
ZD2 D9 ZD3
R14
1W
47
KJ
R56
1W
47
KJ
ZD175V
R1110KJ
GND
C20
C25
U3KA431
R34330J
D104148
R5224KJ
R59
5W15mJ
R281KJ
D6
200V1A
D7
60
V2
0A
Q7A709
C1050V1uF
D1260V3A
C29
10V10OOuF
+5V0.8A
D3200V1A
D8 60V3A
C23
+24V
1.5A
R32
R131/2W6.8J
C1635V1000uF
C32100V103J
R121W22J
R313SP10
C171KV222K
R8
1W
22
KJ
C28
R23
10KJ
R451W6.8J
CON3
R35330J RV1
100J
F1250V8A
TNR1
10D221
R11W560KJ
R46
1W6.8J
LF1L5861
AR2 1KV
AR1 1KV
LF2L5858
F2250V5A
C9
20
0V
12
00
uF
R9
1W
22
KJ
Q3500V24A
R22
1W0.2JX2
RV2500J
R26
10KJ
C14681J
L3-1
L5856
C21
35
V1
00
0u
FX
3
R5336J
R44510J
R434.7KJ
R421KJ
C2650V1uF
U2KA431
R27
3W
1K
JX
2
R91/2W100mJ
R301/2W40mJ
F3250V4A
L4L5843
R381KF R
29
1K
F
Q5A709
C24
16
V2
20
0u
FX
3
L3-2L5856
I1 O 2
G3
C4 U4
KA78R05
C27
50V1uF
TH1THERMISTORC41
472MX2
L5L5844
L2AY-70
R4100J
R1710KJ
C181KV102K
R371W22J
AC INPUT 1
4
4
3
6
5
7
8
1
2
T1
15.16
13.14
9
10
11
12
1.2.3.4
9.10
1/4W
Bigbang-v1 Power Supply
YW396
CON1
21
PIN
CON2
5096-02C
Q2BTA12-600B
BD1600V5A
R71/4W1KJ
C8104K
R61W22J
D44148
Q4
80
0V
13
A R24220J
CS 8
CT
7
RT
1
FB
2
GN
D4
OUT5
IS3
VC
C6
U1 KA7553
R51W180J
0
0
00
PC1S21ME4
+2
4V
VF
C3102
C2102
C5224
C4224
C1474
C9
40
0V
27
0u
F
C13222J
R16100J
R1922J
R21 PC3-1 R188.2KJ
C14681J
C15104K
PC2-1
Q1
BT
A1
2-6
00
B
R4
1/8
W2
2J
C7
10
4K
R58
1W
1.5
KJ
R21W47J
C6630V103K
D1200V1A
D21KV1A
C12
50
V4
7u
F
ZD427V
C22
+24VF
3.5A
GND
+3.3V3.5A
D13200V20A
PC3-2
L3-1
L5856
Q6C1008
D114148
R50220J
PC2-2
R514.7KJ
R4910KJ
R1510KJ
R54220J
R39220J
R5747KJ
GND
ZD227V
D94148
ZD35.1V
R14
1W
10
0K
J
R56
1W
10
0K
J
ZD1150V
GND
C20
C25
U3KA431
R34330J
R35330J D10
4148
R52
R59
5W15mJ
R281KJ
D6
200V1A
D7
60
V2
0A
Q7A709
D1260V3A
C29
10V10OOuF
+5V0.8A
D3200V1A
D8 60V3A
C23
+24V
1.5A
R32
C1635V1000uF
I1 O 2
G3
C4 U4
KA78R05
R121W22J
R313SP10
C28
R451W6.8J
R461W6.8J
CON3
RV2
RV1100J
F1250V8A
TNR1
10D561
R11W560KJ LF1
0610V
AR2 1KV
AR11KV
F2250V5A
LF2L5842
L1L5857
R8
1W
47
KJ
R10
1W
47
KJ
R22
1W0.44JX2
R2310KJ
R111/4W10KJ
R131/2W6.8J
C21
35
V1
00
0u
FX
3
R5336J
R44510J
R434.7KJ
R421KJ
C2650V1uF
U2KA431
R411KJ
R27
2W
1K
JX
2
R91/2W100mJ
R301/2W40mJ
F3250V4A
L4L5843
C32100V103J
L5L5844
C1050V1uF
R381KJ
R2
92
2K
F
Q5A709
C24
16
V2
20
0u
FX
3
L3-2L5856
C27
50V1uF
TH1THERMISTORC41
472MX2
L2AY-70
R1710KJ
C171KV222K
C181KV102K
R371W22J
AC INPUT 1
4
4
3
6
5
7
8
1
2
T1
15.16
13.14
9
10
12
1.2.3.4
9.10
11
1/4W
Bigbang-v2 Power Supply
YW396
CON1
21
PIN
CON2
5096-02C
Q2BTA12-600B
BD1600V5A
R71/4W1KJ
C8104K
R61W22J
D44148
Q4
80
0V
13
A R24220J
CS 8
CT
7
RT
1
FB
2
GN
D4
OUT5
IS3
VC
C6
U1 KA7553
R51W180J
0
0
00
PC1S21ME4
+2
4V
VF
C3102
C2102
C5224
C4224
C1474
C9
45
0V
27
0u
F
C13222J
R16100J
R1922J
R21 PC3-1 R188.2KJ
C14681J
C15104K
PC2-1
Q1
BT
A1
2-6
00
B
R4
1/8
W2
2J
C7
10
4K
R58
1W
1.5
KJ
R21W47J
C6630V103K
D1200V1A
D21KV1A
C12
50
V4
7u
F
ZD427V
C22
+24VF
3.5A
GND
+3.3V3.5A
D13200V20A
PC3-2
L3-1
L5856
Q6C1008
D114148
R50220J
PC2-2
R514.7KJ
R4910KJ
R1510KJ
R54220J
R39220J
R5747KJ
GND
ZD227V
D94148
ZD35.1V
R14
1W
10
0K
J
R56
1W
10
0K
J
ZD1150V
GND
C20
C25
U3KA431
R34330J
R35330J D10
4148
R52
R59
5W15mJ
R281KJ
D6
200V1A
D7
60
V2
0A
Q7A709
D1260V3A
C29
10V10OOuF
+5V0.8A
D3200V1A
D8 60V3A
C23
+24V
1.5A
R32
C1635V1000uF
I1 O 2
G3
C4 U4
KA78R05
R121W22J
R313SP10
C28
R451W6.8J
R461W6.8J
CON3
RV2
RV1100J
F1250V8A
TNR1
10D561
R11W560KJ LF1
0610V
AR2 1KV
AR11KV
F2250V5A
LF2L5842
L1L5857
R8
1W
47
KJ
R10
1W
47
KJ
R22
1W0.44JX2
R2310KJ
R111/4W10KJ
R131/2W6.8J
C21
35
V1
00
0u
FX
3
R5336J
R44510J
R434.7KJ
R421KJ
C2650V1uF
U2KA431
R411KJ
R27
2W
1K
JX
2
R91/2W100mJ
R301/2W40mJ
F3250V4A
L4L5843
C32100V103J
L5L5844
C1050V1uF
R381KJ
R2
92
2K
F
Q5A709
C24
16
V2
20
0u
FX
3
L3-2L5856
C27
50V1uF
TH1THERMISTORC41
472MX2
L2AY-70
R1710KJ
C171KV222K
C181KV102K
R371W22J
AC INPUT 1
4
4
3
6
5
7
8
1
2
T1
15.16
13.14
9
10
12
1.2.3.4
9.10
11
1/4W
Bigbang-v2c Power Supply