2
SALOON AND BARBER SHOP LIST OF PARTS: BEFORE STARTING: • Check parts against list above. • Carefully trim any excess plastic from the parts before assembling. • You may wish to add a few drops of styrene cement to joints for permanent construction. ASSEMBLY INSTRUCTIONS: (use photos as a guide) • With large tab at top, place window tab into opening from outside of wall first, and then snap window in place. Repeat for all windows. Note two types of windows. • From inside walls, line up doors with hinge pins at top and bottom (1) (making sure the finished side faces outward and windows are toward top of door), drop door down so it hangs by hinges (2), and then gently snap under center tab (3 and 4). See photos 1, 2, 3, and 4 on reverse side. Note that the door with windows fits into right side doorway and solid doors fit into left side and barbershop doorways. • Press (2) lamps into holes next to saloon doorway. From the outside, snap saloon doors into grooves provided. • Press adhesive signs onto balcony sign board and over barber shop; press striped sticker around barber pole. • Press lower walls together matching A to A, B to B, C to C and D to D (walls marked inside ends), and also insert bottom of wall corners into the floor. Corner pins in floor must fit into correct corresponding holes in bottom of walls. See photo on reverse side. • Press woman’s figure and sign board into holes in balcony. Press railings into row of inner-most holes in balcony, making sure round knobs on railings are on top. • Slide balcony securely into place in front of building. • Push (4) uprights, barber pole, and male figure into holes in front walk and then press front walk onto lugs on front wall and insert tops of uprights into upper balcony. Press upper walls together matching E to E, F to F, and G to G and insert into balcony. • Press large and small stairs, cellar door, and smokestack into holes provided. • Assemble 2-piece chimney, insert into roof, and then press roof into place. 2 front walls (upper & lower) 1 rear wall 1 left side wall 2 right side walls (upper & lower) 1 balcony 1 sticker sheet 1 front walk 4 uprights 1 chimney (2 pc.) 1 roof 1 sign board 2 lamps 1 set stairs - large 1 set stairs - small 13 open windows (small) 7 closed windows (large) 2 solid doors; 1 door with windows 2 saloon doors 3 railings 2 figures (shown painted for illustrative purposes only) 1 barber pole 1 smokestack 1 cellar door 1 floor upper front wall balcony lower front wall barber pole lamp saloon doors front walk upright railings solid door

SALOON AND BARBER SHOP LIST OF PARTS - Bachmann Trains€¦ · SALOON AND BARBER SHOP LIST OF PARTS: BEFORE STARTING: • Check parts against list above. • Carefully trim any excess

  • Upload
    others

  • View
    7

  • Download
    0

Embed Size (px)

Citation preview

Page 1: SALOON AND BARBER SHOP LIST OF PARTS - Bachmann Trains€¦ · SALOON AND BARBER SHOP LIST OF PARTS: BEFORE STARTING: • Check parts against list above. • Carefully trim any excess

SALOON AND BARBER SHOP

LIST OF PARTS:

BEFORE STARTING:• Check parts against list above.• Carefully trim any excess plastic from the parts before assembling.• You may wish to add a few drops of styrene cement to joints for permanent construction.

ASSEMBLY INSTRUCTIONS: (use photos as a guide)• With large tab at top, place window tab into opening from outside of wall first, and then snap window in place. Repeat

for all windows. Note two types of windows.• From inside walls, line up doors with hinge pins at top and bottom (1) (making sure the finished side faces outward and

windows are toward top of door), drop door down so it hangs by hinges (2), and then gently snap under center tab (3 and 4). See photos 1, 2, 3, and 4 on reverse side. Note that the door with windows fits into right side doorway and solid doors fit into left side and barbershop doorways.

• Press (2) lamps into holes next to saloon doorway. From the outside, snap saloon doors into grooves provided. • Press adhesive signs onto balcony sign board and over barber shop; press striped sticker around barber pole.• Press lower walls together matching A to A, B to B, C to C and D to D (walls marked inside ends), and also insert

bottom of wall corners into the floor. Corner pins in floor must fit into correct corresponding holes in bottom of walls. See photo on reverse side.

• Press woman’s figure and sign board into holes in balcony. Press railings into row of inner-most holes in balcony, making sure round knobs on railings are on top.

• Slide balcony securely into place in front of building.• Push (4) uprights, barber pole, and male figure into holes in front walk and then press front walk onto lugs on front wall and

insert tops of uprights into upper balcony. Press upper walls together matching E to E, F to F, and G to G and insert into balcony.

• Press large and small stairs, cellar door, and smokestack into holes provided.• Assemble 2-piece chimney, insert into roof, and then press roof into place.

2 front walls (upper & lower)1 rear wall1 left side wall2 right side walls (upper & lower)1 balcony1 sticker sheet1 front walk4 uprights

1 chimney (2 pc.)1 roof1 sign board2 lamps1 set stairs - large1 set stairs - small13 open windows (small)7 closed windows (large)

2 solid doors; 1 door with windows2 saloon doors3 railings2 figures (shown painted for illustrativepurposes only)1 barber pole1 smokestack1 cellar door1 floor

upper front wall

balcony

lower front wall

barber polelampsaloon doorsfront walk

upright

railings

solid door

Page 2: SALOON AND BARBER SHOP LIST OF PARTS - Bachmann Trains€¦ · SALOON AND BARBER SHOP LIST OF PARTS: BEFORE STARTING: • Check parts against list above. • Carefully trim any excess

smokestack

43

1 2

center tab

Printed in China

H5162-IS001

small window large windows

rear wall

left side wall

large stairs cellar door

chimney

roof

right upper wall

right lowerside wall

small stairs

sign board

door with windows

solid door

floor pin