Upload
others
View
4
Download
1
Embed Size (px)
Citation preview
Cyrusher Sports Team
www.cyrusher.com
1 / 27
S700 Bike Computer User Manual
This bike computer user manual is only for Cyrusher XF500,Extrbici XF660 1000W, Cyrusher
XF690, Cyrusher XF770, Lankeleisi XT750,Lankeleisi G550,Lankeleisi T8 and Lankeleisi XT750
plus operations setting reference.
If you are using other Cyrusher or Lankeleisi Ebikes models, please contact Cyrusher Sports
Team for help.
Bike Computer Screen:
Technical Symbol Definition:
Cyrusher Sports Team
www.cyrusher.com
2 / 27
AVG: Average Speed
MAX: Max. Speed
Speed: Real Time Speed
DST: Driving Mileage (Estimated how far you can drive based on the current battery capacity)
Front Light
Walk Mode/ Cruise Control/ Pedal Assistant Power Level and Number
Battery Remains
TRIP: Single Odometer
ODO: Total Odometer
TM: Bike Computer Working /Cycling Time ( it tells many hours the bike computer has started
Cyrusher Sports Team
www.cyrusher.com
3 / 27
for working)
ERR: Error Code
Operation Setting:
In default setting of S700 bike computer:
⚫ Please note that PAS 0 means only throttle works;
⚫ PAS 1-5 means only Pedal assistant works but throttle does not work.
1. Turn on/ Turn off bike computer: Press for seconds to turn or turn off the
bike computer;
2. Turn on/ Turn off bike front light: After turning on the bike computer and press
for 3 seconds to turn on or turn off front light.
3. Active walk mode(Optional) : After turning on the bike computer and press
for 3 seconds to active the walk mode
4. Increase/ Decrease PAS Level: After turning on the bike computer and press
to increase the PAS Level and Press to decrease PAS level.
5. ODO/TRIP/ERR/TIME Checking: After turning on the bike computer and press
one time to switch and check data of ODO/TRIP/ERR/TIME. (Images Below)
Cyrusher Sports Team
www.cyrusher.com
4 / 27
6. Enter Setting Mode: After turning on the bike computer and press
and together for 3 seconds to enter setting mode,
Then press to switch P level setting from P01 to P18
and press or to choose the right data code for each P level
setting.
Cyrusher Sports Team
www.cyrusher.com
5 / 27
7. Speed/AVG/Max Checking: After turning the bike computer, press +
for 3 seconds to switch and check data of Speed/AVG/Max.( Images Below)
P Level Setting Code Definition:
P01: Brightness Setting,
Range:1-3, 1 is darkest, 3 is brightest;
P02: Speed Unit Setting ( How to change the Speed Unit to Miles or KMS ?)
Range: 0-1; 0 is KM, 1 is Mile
In the setting modes, change the P02 code from 00000 to 00001 by press or
the speed unit will be in Miles/H;
Cyrusher Sports Team
www.cyrusher.com
6 / 27
P03: Working Voltage Setting,
Range: 24V,36V, 48V;
P04: Bike Auto Shutting-down Time Setting
Range:1-60
It means if you do not operate the bike computer or use the e-bike within the minutes range
from 1 to 60 minutes, the bike computer will shut down automatically;
P05: PAS Preference Setting
Range:
0 ---only shows 1-3 levels;
1 ----shows 1-5 levels;
2----shows 1-9 levels;
Just PAS level number are different, but top and lowest level power is the same, such as 3=
5=9 in different working modes;
P06: Wheel/rim diameter Setting (Inch)
Range: 20/22/26/28 (Normally, if 20 inch rim, setting number will be 22inch)
P07: Speed Monitor Setting,
Range: 1-100;
This technical setting is only for engineer setting, do not modify or change the setting.
Cyrusher Sports Team
www.cyrusher.com
7 / 27
P08: Speed Limit Setting.
Range: 1-100KM;
If setting data is 100KM,which means there is no speed limit, however, the real speed limit of
e-bike is controlled by motor and controller. You can only set the bike computer speed limit
within the given the range fixed by motor and controller. For example, if the motor and
controller fixed top speed limit is at 40KM/H, you can only set lower top limit such as 35KM/H,
then the e-bike will keep run within the top speed limit-- 35KM/H; If you set 50KM/H, the
real top speed limit is only 40KM/H;
P09: Zero boost or Non-Zero Boost Setting.
Range: 0 means zero boost; 1 means non zero boost.
In the zero boost also called hard boost which means, once you use the throttle or pedal
assistant, you get will push from the motor immediately; In non-zero boost, you have to use
pedal first to move the e-bike to some certain speed and the throttle or PAS will be active.
P10: Driving Modes Setting;
Range:
0 – PAS only, the throttle is not working;
1—throttle only, PAS is not working;
2—both throttle and PAS are working;
P11: PAS Sensitivity Setting
Range: 1-24,
This technical setting is only for engineer setting, do not modify or change the setting.
P12: PAS Strength Setting
Range: 1-5,
This technical setting is only for engineer setting, do not modify or change the setting.
P13: PAS Magnetic Sensor Setting
Range: 5/ 8/12
This technical setting is only for engineer setting, do not modify or change the setting.
P14: Controller Max Current Limit Setting
Range: 1-20A;
Cyrusher Sports Team
www.cyrusher.com
8 / 27
P15: Controller Low voltage Setting.
Range: N/A,
Need to check with controller technical data sheet for reference;
P16: ODO, Total Odometer Clearance Setting
In setting mode, press for 5 seconds in setting mode, you can change and clear
the current total odometer to Zero.
P17: N/V
Range: 100(default)
This technical setting is only for engineer setting, do not modify or change the setting.
P18: Bike Computer Reset Setting
In setting mode, press for 5 seconds in setting mode, reset the bike computer in
the bike computer default setting ONLY(not the e-bike) once SSSS shows on LCD.
.
Cyrusher Sports Team
www.cyrusher.com
9 / 27
Please note that the default setting is only for S700 bike computer itself and it is not same
default setting for each mode of electric bike. For example, although XF500 and XF770 are
using the same bike computer, however, their default setting number maybe different at the
same P Levels setting.
Error Codes:
Range/Problem/Solution:
00000--- Normal
00006---Low Battery Voltage---Need charge battery;
00007---Motor Failure---Check motor cable connection whether loose or damage;
00008---Throttle Failure—Check throttle cable connection whether loose or damage;
00009---Controller Failure—Check controller cable connection whether loose or damage or
incorrect connection;
00010---Data Receiving Failure—Check bike computer connection whether loose or damage
00011---Data Sending Failure—Check bike computer connection whether loose or damage;
Default Bike Computer Setting for XF770 Only (Images Below)
Other Models of e-bikes Default Setting are different in P06 as following:
XF500/G550---P06—22 inch;
T8/XF770/XT750---P06—26 inch;
XF660-1000W/XF690/XT750 Plus ---P06---28inch;
Cyrusher Sports Team
www.cyrusher.com
10 / 27
Cyrusher Sports Team
www.cyrusher.com
11 / 27
Cyrusher Sports Team
www.cyrusher.com
12 / 27
Cyrusher Sports Team
www.cyrusher.com
13 / 27
Cyrusher Sports Team
www.cyrusher.com
14 / 27
Cyrusher Sports Team
www.cyrusher.com
15 / 27
Cyrusher Sports Team
www.cyrusher.com
16 / 27
Cyrusher Sports Team
www.cyrusher.com
17 / 27
Cyrusher Sports Team
www.cyrusher.com
18 / 27
Cyrusher Sports Team
www.cyrusher.com
19 / 27
Cyrusher Sports Team
www.cyrusher.com
20 / 27
Cyrusher Sports Team
www.cyrusher.com
21 / 27
Cyrusher Sports Team
www.cyrusher.com
22 / 27
Cyrusher Sports Team
www.cyrusher.com
23 / 27
Cyrusher Sports Team
www.cyrusher.com
24 / 27
Cyrusher Sports Team
www.cyrusher.com
25 / 27
Cyrusher Sports Team
www.cyrusher.com
26 / 27
Cyrusher Sports Team
www.cyrusher.com
27 / 27