Rudolph The Red Nosed Luminary 13 - Delphi Glass Krafty Blok eBook-219512.pdf · 18. Place the KraftyBlok™ on its back with the “Owl” image facing up. Apply glue to Section

Pumpkin Head Lamp ........................................3Wooden Owl Night Light ...................................5Autumnal Dreams .............................................7Here Kitty, Kitty .................................................9Flower Power Lamp ........................................11Rudolph The Red Nosed Luminary ................13Lasting Sentiments .........................................15Frit Art Candle Cubes .....................................17Holiday Snow Block ........................................18Chanukah Luminary ......................................20Little Bloomin’ Night Light ...............................22KraftyBlok™ Kaleidoscope Lamp ...................24Spa Day Bank .................................................26Cute As A Button Canister ..............................28Decoupage Bank ............................................30Billy The Snowman .........................................31Let It Snow Lightbox .......................................32“Remember When Bank” ................................33Nest Egg Bank ................................................34Night Before Christmas Victorian Scene ........35The First Noel! ................................................37Painted KraftyBlok™.......................................38Chrtistmas Tree Accent Light ..........................39Oriental Garden ..............................................41Summer Song Birds .......................................43

© 2014 by Delphi Glass Corp. with permission from Diamond Tech Crafts

KraftyBlok™

eBook

Table of Contents

Please note that items numbers listed in these project guides are suggested items that can be purchased at www.DelphiGlass.com. The items may not always be identical to those used in these project examples and are subject to change.

DELPHIGLASS.COM

Project Help Line • 800.821.9450© 2014 Delphi Glass Corp.

3

Pumpkin Head Lamp Designed by: Jeanne Baruth

Tips:• Read all of the KraftyBlok™ Image Art instructions before starting

your project.• Large profile decals are fragile, handle with care.• This project requires the use of a laser printer, not an inkjet.

Materials:• 71/2" KraftyBlok™ (#425100)• KraftyBlok™ Large Stand (#426121)• Image Art™ Paper (#427200)• E6000 Glue® (#8919)• 3/8" Venetian Tile Assortment (#42719A)

or Jennifer’s Mosaics™ Classico Glass Mosaic Tile• Night Light Socket and Cord Set• (Optional) Black Enamel Paint and Black Glitter Paint• (Optional) Halloween Ribbon and hot glue

Instructions: 1. Clean your KraftyBlok™ inside and out and dry completely.2. Place the KraftyBlok™ flat on a work surface with the opening at

the bottom. Measure, center and mark a 51/2" x 51/2" square on both faces of the KraftyBlok™.

3. Copy and resize pumpkin image to 51/2" x 51/2" using any software that allows you to manipulate and print images.

4. Set up your printer as instructed on the Image Art packaging.5. Follow printers’ instructions and print transfer. Allow paper to set

10 to 15 minutes to dry. Trim to size with scissors.6. Place transfer in a bowl of water and wait approximately 1 minute.7. Lightly moisten the area marked off on the face of the block. Center the transfer inside the

designated area. Roll a ½" of the backing paper away from the top of the Image Art transfer (the decal). Take extra care when sliding the image as they are delicate and can tear easily. Gently slide the Image Art transfer from the backing paper onto the surface using your fingers to smooth the decal as you peel away from the backing paper.

8. Gently pat and smooth the Image Art transfer with a moist paper towel eliminating air pockets and wrinkles. Allow to dry 10 minutes.

9. Carefully turn the KraftyBlok™ over onto a soft towel so the opening is facing down, apply the second image to the back. NOTE: If you do not allow enough time for the first transfer to dry, it will get marred when you flip it over.

DELPHIGLASS.COM


4

Pumpkin Head Lamp 10. Allow both transfers to dry overnight.11. To permanently set the transfer, preheat a conventional oven to 345°F.

Place the KraftyBlok™ with the opening facing down on a baking rack. Do not allow either side of the block containing the Image Art transfer to lie against the baking rack. Bake for 15 minutes. Turn off oven, prop door slightly, and allow it to rest for 20 minutes.

12. When oven and block are completely cool, remove from oven and hand wash using a mild soap and water. Dry with a lint-free cloth.

13. Lie block flat on a covered work space. Tape off edges around the pumpkin and the sides of the block using painter’s tape. Paint inside the taped area with black enamel paint to create a frame. Allow to dry completely.

14. Once dry, apply black glitter paint over the black enamel paint on the front of the block. Allow to dry according to the manufacturer’s instruction.

15. Once dry, score around the painted edges of the tape with a craft knife and a ruler. This creates a clean sharp edge when you remove the tape. Slowly remove the tape. Repeat step 13 on the opposite side.

16. Next, place orange and black 3/8" tiles around the pumpkin transfer on the front face of the block, alternating colors. Once in place, lift tiles and glue into place.

17. Finish project by measuring and cutting a 20" length of ¾", 1¼" and 2¼" ribbon. Place the 2¼" ribbon flat on your work surface, center and layer the ¾" and 1¼" ribbon on top over the 2¼" ribbon. Apply a dot of hot glue on each layer to hold into place. Fold over one edge of the ribbon ½" and glue to one side of the opening. Wrap the ribbon around the block and finish by folding the remaining end under ½" and glue next to the remaining side of the opening.

18. Glue other embellishments, such as a scrapbook die cut of a little bitty spider.19. Insert a light into the project and place the embellished KraftyBlok

into the stand. Your Pumpkin Head Lamp is ready to light up the festivities with a boo-tiful glow!

DELPHIGLASS.COM

5

Wooden Owl Night LightDesigned by: Jeanne Baruth

Tips:• Read all of the KraftyBlok Image Art™ instructions before

starting your project.• This project requires the use of a laser printer, not an inkjet.

Materials:• 5 5/8" KraftyBlok™ (#426112)• Image Art™ Paper (#427200)• E6000® Glue (#8919)• Night Light Socket and Cord Set• Wooden Buttons• Balsa Wood – Revell Balsa Project Bag (www.revell.com)• Clear Acrylic Varnish & brush

Instructions: 1. Copy and resize owl image to 4" x 4", and the six secondary

images to 1" x 1" using any software that allows you to manipulate and print images.

2. Set up your printer per the instructions on the Image Art™ packaging.

3. Follow printers’ instructions and print transfer. Allow transfer to set 10 to 15 minutes to dry. Trim all decals to size using a scissors.

4. Remove the stopper from your KraftyBlok™, clean with glass cleaner and a lint free cloth.

5. Place transfer in a bowl of water and wait approximately 1 minute.6. Lay the KraftyBlok™ flat on your work area with the opening at the bottom.

Slightly moisten the face of the block. Position the transfer above the surface; roll a ½" of the backing paper away from the top layer of the Image Art™ transfer (the decal). Line up the Image Art™ transfer on the surface. Take extra care when sliding the image as they are delicate and can tear easily. Gently slide the Image Art™ transfer from the backing paper onto the surface. Use your fingers to smooth the transfer as you peel away from the backing paper.

7. Gently pat and smooth the Image Art™ transfer with a moist paper towel, eliminating air pockets and wrinkles.8. Stand the block up with the opening on the bottom. Moisten and apply the six secondary images to the backside of the glass and repeat step seven.9. Allow to dry over night.10. To permanently set the transfer, preheat a conventional oven to 345°F. Place the KraftyBlok™ with the opening facing down on a baking rack.

Do not allow either side of the block containing the Image Art transfer to lie against the baking rack. Bake for 15 minutes. Turn off oven, prop door slightly, and allow it to rest for 20 minutes.

11. When oven and block are completely cool. Remove from oven and hand wash using a mild soap and water. Dry with a lint-free cloth.


DELPHIGLASS.COM


6

Wooden Owl Night Light12. Cut the following lengths of balsa wood with a utility knife:

KRAFTYBLOK™ BOX FAME Section A: Sides – 7" x 3" x 1/8" – two Section B: Top – 6¼" x 3" x 1/8" – one Section C: Front and Back Bottom 13/8" x 5¾" x 1/8" – two IMAGE FRAME: Section D: Frame Sides 41/8" x ½" x 1/16" – two Section E: Frame Top and Bottom 3 7/16" x ¾" – two NOTE: Balsa is a soft wood and will reduce quickly. If edges are rough, lightly sand with 150 grit sand paper. Place the sand paper flat on your table, grit side up. Gently slide the wood back and forth over the paper until smooth.

13. To create the box frame around the KraftyBlok™, stand the block with the opening facing down. Apply glue along the raised edges of the top of the block. Center Section B over the glue and press in place so that there is a 1/8" overhang on each side.

14. Flip the block over so the glued surface is resting against the table. Gently press down to seat the wood into the glue.

15. Next, apply glue along the raised edges on either side of the block. Press both Section A wood pieces onto each side. Examine joints closely to ensure they are even and square. Allow 15 minutes to dry. TIP: Rubber bands can be used to hold wood in place. Do not use rubber bands that are too small, as they will dent the soft wood.

16. Apply glue to both ends of one Section C panel. Slip it in-between the side panels so it rests on the bottom front of the block.

17. For the bottom back panel, cut a ¼" square notch on the center bottom of the remaining Section C panel (for the lighting cord). Apply glue to both ends of this panel and slip it in-between the side panels so it rests notched side down on the bottom back of the block. Allow the project to dry for 15 minutes.

18. Place the KraftyBlok™ on its back with the “Owl” image facing up. Apply glue to Section D and apply to the top of the image. Apply glue to Sections E and apply them to either side of the image. Finish frame, by gluing the remaining Section D to the bottom of the image. Using the image for placement add wooden buttons to the image.

19. Allow project to dry completely per glue manufacturer’s instruction.20. Use a foam brush to apply clear varnish to the wood to seal it.21. Remove the KraftyBlok™ stopper and insert a 5-watt silicone candle bulb on a nightlight cord into the

opening. The prongs on the light cord will snap into the opening at the bottom of the stand and hold the light upright.

Picture 7

DELPHIGLASS.COM


4DELPHIGLASS.COM

7

Autumnal DreamsDesigned by: Jeanne Baruth

Skill Level: (Adult 1-5: 1 being the easiest, 5 being most difficult) 4

Time to Complete: 2 hours -Does not include drying time.

Materials:• KraftyBlok™ Original (#425100)• KraftyBlok™ Large Stand (#426121)• Adirondack® Alcohol Inks – Farmer’s

Market Collection (www.rangerink.com)• 1" Foam Brush• Versamark Ink Pad• Stampin’Up!™ Tree Stamp

(www.elizabethloves2stamp.stampinup.net)• Stampin’Up!™ Embossing Powder –

Black and Gold• Heat Gun• Night-light on a cord

(www.Sunshinecrafts.com)• 5-watt Silicone Candle Bulb

(www.Sunshinecrafts.com)• 20" Beaded Fringe in a coordinating color

(fabric store trim department)• Hot Glue & Gun• Paper Towels

Instructions: 1. Protect your work area with several

layers of newspaper.2. Clean your block with glass cleaner and a paper towel.3. Place the KraftyBlok™ face down on a flat work surface with the opening facing towards you.4. Remove the cap from your first bottle of alcohol ink. Squirt a bit of ink onto the KraftyBlok™ surface. To avoid spills, place a paper towel

over the tip of the ink bottle, then invert. Squirt a small puddle of ink. Repeat this process with, as many colors you choose to use.5. Tilt the KraftyBlok™ from side to side, back and forth distributing the ink across the surface of the glass, move quickly.6. Apply several drops of alcohol ink to the tip of a 1" foam brush. Using long quick strokes, apply ink to the sides, top, and bottom of

the block. Allow ink to dry completely.

DELPHIGLASS.COM


8

Autumnal Dreams7. Stand the block up with the opening facing down on

the newspaper. Apply alcohol inks to the sides of the block in alternating colors. Allow the inks to run down the sides. Continue to create runs until you are satisfied with the look. Touch up with the foam brush on edges if necessary. Allow ink to dry.

8. When dry, place the KraftyBlok™ on the work surface with the opening facing up.

9. Using a VersaMark inkpad and ink a “tree” stamp of your choice. Carefully stamp the glass several times creating multiple images as shown in the photograph. Feel free to overlap stamped images.

10. Sprinkle embossing powder over the tree images, making sure all trees have powder sticking to them. Tap off the excess powder.

11. Using the embossing gun, melt down the powder until it is smooth. Be careful not to overheat, which will cause the embossing powder to bubble.

12. Allow KraftyBlok™ to cool.13. Remove the KraftyBlok™ stopper and place the

KraftyBlok™ in the stand with the opening at the bottom. Insert a 5-watt silicone candle bulb on a nightlight cord into the opening. The silver prongs on the light cord will snap into the opening at the bottom of the stand and hold the light upright.

14. Add trim to the base of the stand by placing a dot of hot glue on one leg of the stand beneath the KraftyBlok™. Stretching the trim across the stand front and glue to secure in place. Continue this process until the trim is wrapped completely around the bottom of the stand. Add additional dot of hot glue if necessary to keep the fringe in place and from drooping.

Plug your lamp in and enjoy the soft warm glow.

Here Kitty, Kitty! Designed by: Jeanne Baruth


Time to Complete: 1 hour - Does not include drying time.

Project Tip:Betta fish are beautiful, with their vibrant colors and long, flowing tails. The bettais relatively hardy, but needs care. Before investing in a betta fish find out more at www.bettafish.com.Sea Monkeys would also be a good choice for type of habitat. Moreover, for those hesitant to become a pet owner, Artificial Plastic Floating Fish Ornaments for Aquariums are available online.

Materials:• Laser Color Printer• KraftyBlok™ Mini (#426112)• KraftyBlok™ Image Art Paper

(# 425878)• Kitty image, pg. 10• Glass Gems ½" (#425270)• Small Aquarium Plant• Beta Fish, Sea Monkey’s, or Artificial

Plastic Floating Fish Ornaments for Aquariums

• E6000® Glue (#8919)• Paper Towels• Bowl for water• Scissors

DELPHIGLASS.COM


9

DELPHIGLASS.COM


10

Picture 7

Here Kitty, Kitty! Instructions: 1. Set your printer following the instructions on the

KraftyBlok™ Image Art package. Copy and save the kitty image to your computer. Print image using your available image software. Allow paper to set 10 to 15 minutes to dry. Trim to size with scissors.

2. Place transfer in a bowl of water and wait approximately 1 minute.

3. Place the KraftyBlok™ on a flat work surface with the opening facing away from you. Slightly moisten the face of the block with a wet paper towel.

4. Position the transfer above the surface at the top of the block. Roll a ½" of the backing paper away from the top of the Image Art transfer (the decal). Place the transfer on the surface of the block so it is parallel with the top edge. Take extra care when sliding the decal as they are delicate and can tear easily. Gently slide the Image Art full transfer from the backing paper onto the surface. Use a finger to smooth the transfer as you peel away from the backing paper.

5. Gently pat and smooth the Image Art transfer with a moist paper towel eliminating air pockets and wrinkles.

6. Allow to dry overnight.7. Use a clear sealer specifically formulated for sealing

decals to glass. Mask off area around the transfer to prevent overspray from getting on the rest of your project.

8. Spray the sealer according to the manufacturer’s directions and allow it to dry.9. OPTIONAL: To add a bit of whimsy, create feet by applying four glass cubes, ceramic tile or flat beads

to the bottom of the KraftyBlok™. Glue in place using E6000® and allow them to dry according to the manufacturer’s recommendation.

10. Remove the stopper and rinse the interior of the KraftyBlok™, the glass gems and the plastic plant with spring or distilled water before assembling the aquarium.

11. Fill the block with approximately one inch of gems. Insert the plastic plant off to one side. Follow your pet shop specialist’s information in preparing the KraftyBlok™ for your selected species.

DELPHIGLASS.COM


11

Flower Power LampProject Tip:Begin by choosing an image for the front of your lamp. Next, choose glass to compliment the colors in the image. For our lamp we used Spectrum Rough Rolled Grape (#S5432RR) and Deep Aqua (#S5333RR) for the sides and top and Clear Sandblasted (#M4053) glass for the back panel and flower accents.

Materials:• Clear KraftyBlok™ (#426112)• Creative Image Color Slide™ (#8303)• Spectrum Grape Rough Rolled (#S5432RR)• Spectrum Deep Aqua Rough Rolled

(#S5333RR)• Clear Sandblasted (#M4053)• Silicone Adhesive (#5690)• Self-Adhesive Clear Rubber Feet (#69501)• Glass cutting tools: Glass Cutter (#425655),

Running Pliers (#5068), Breaker/Grozer (#63989)

• Cellophane Tape• Waterproof container• Soft brush or sponge brush• Glass Grinder or Abrasive Stone (#5169)

Artist: Julie Haan

DELPHIGLASS.COM


12

Flower Power Lamp

Print your image on the Color Slide according to the manufacture’s instructions. Cut your image to size, leaving a narrow border of unprinted paper around the image.

Fill the container with 2" of warm water. Place the image in the water and gently unroll. Soak for 30 sec. or until the image slides easily from the paper backing. Meanwhile, using a soft brush, apply a coat of water to the inside of the KraftyBlok™ where you want to place the image. This will make it easier to adjust the image when it is placed.

Remove the image from the water and lay it slick side up on your work surface. Gently lift the image from the water and place it face-down on top of the backing paper. (The adhesive side should be up.) Loosely roll the image and place it in the KraftyBlok ™ image side down. Peel off the paper backing.

With a soft brush, adjust the image and smooth out any air bubbles. Blot with a paper towel and let dry.Cure according to the instructions included with the Creative Image Color Slide™*Note: Our image is mounted on the inside of the KraftyBlok™.You can also choose to mount the image on the outside.

Cut the Spectrum Grape and Deep Aqua glass into 1" x 51/2" strips for the sides and top of the lamp. You will need 3 strips of each color. Cut one 41/2" square of Clear Sandblasted glass for the back. Next, cut teardrop shapes for the flower petals from the Clear Sandblasted glass and round centers from the Grape and Deep Aqua.

Apply a dime size drop of silicone adhesive to the corner area of the shiny side of the Clear Sandblasted Square. Attach the square to the back of the KraftyBlok™. Glue one Grape and one Deep Aqua strip side by side on each of the two sides and the top of the KraftyBlok™. Use cellophane tape to hold the glass in place until the adhesive dries then remove the tape.

On the image side of the lamp, apply the teardrop flowers, again applying the silicone adhesive to the shiny side.Apply the self-adhesive rubber feet to the bottom corners of the KraftyBlok™. This will allow room for the lamp cord and provide stability.

You can now wire the lamp if you like or use a LED candle. We used a candle lamp cord, available at your local home improvement store. Using the plastic cap from the hole in the KraftyBlok™, cut an opening large enough to accommodate the fixture. Clip into place. Insert the plastic cap and fixture into the lamp.

DELPHIGLASS.COM


13

Rudolph the Red Nosed LuminaryDesigned by: Lauren Kotovsky

Project Tip:• Wear safety goggles when using glass crafting tools. • Never dispose of grout directly down a drain. • If grouting without latex gloves, pour vinegar over hands to

restore skin PH• Use a clear adhesive so Rudolph’s nose will glow.

Materials:• Original KraftyBlok™ (#425100)• KraftyBlok™ display stand (#426121)• 2-8 oz pkgs Jennifer’s Mosaics ¾" Desert Mix• 1 -8 oz pkg Jennifer’s Mosaics ¾" Denim Mix• 1 pkg Jennifer’s Mosaics 1¼" Glass Gems• Clear Contact Paper• Mosaic Adhesive (#65106)• White Sanded Grout (#425580)• Mixing Bowl and Spoon• Latex Gloves• String of Lights or a Clip-in 4 watt lightbulb with 6' Cord• Sharpie® or Black Paint (optional)• White Paint• Paintbrush (optional)• Craft Knife or Scissors• Sponge

Instructions: 1. Cover work area with newspaper.2. Remove labels from the KraftyBlok™ and clean all surfaces; dry thoroughly.3. Enlarge the pattern (pg 14) to fit the block surface. Place pattern on your work surface

and tape down.4. Cut a piece of contact paper a little larger than the pattern. Remove the backing and place

sticky side up over the pattern, tape into position.5. Nip glass to fit the areas on the pattern, use image as a guide. Press glass firmly onto the

contact paper with the “good” side face down. Omit the glass gem eyes and nose for now. Never nip over the contact paper, as it may cause the paper to become less tacky. For nipping instructions, visit our Creative Corner at www.DiamondTechCrafts.com.

6. When you are satisfied with your mosaic, position the KraftyBlok™ with the flat 8" x 8" surface side up and the stopper opening towards you.

DELPHIGLASS.COM


14

Size pattern to fit KraftyBlok™ surface.

Rudolph the Red Nosed Luminary 7. Apply mosaic adhesive to the surface of the KraftyBlok™ with a

craft stick or disposable knife. Lift the contact paper up and lay over the KraftyBlok™, with the red nose centered above the block opening. Wait about 15 minutes for the glue to set.

8. Using a craft knife, cut the contact paper where the eyes and nose are indicated and glue the 1½" white glass gems into the eyes and the red gem in the nose position.

9. When the glue has dried completely, remove contact paper.10. Measure grout following the manufacturer’s instructions.

Reserve a few tablespoons of grout and set aside. Adding 1 teaspoon of water at a time to grout, mix with a craft stick until the grout reaches “fudge-like” consistency. If too watery, add the reserved dry grout in small amounts until consistency is correct. Mosaic Tip : If you want to color your grout, use an acrylic paint, one teaspoon at a time, until you get your desired color.

11. Wearing disposable gloves, spread grout into the openings around the glass and along the outside edges. Wait about 15 minutes for grout to set. Form a beveled edge border around the mosaic using your finger.

12. Wipe away excess grout using a paper towel or sponge, taking care not to pull grout out of tile spaces. Always remove any grout on the tile surface before it is completely dry.

13. Use a soft cloth; buff the tiles to a clean shine. Allow 24 hours for the mosaic to dry.

14. Take a Sharpie® or black glass paint for the pupil area indicated on the pattern for the eyes. Dot each pupil with a bit of white paint.

15. Place the light bulb or string of lights inside the KraftyBlok™, place in stand and enjoy a little holiday glow!

DELPHIGLASS.COM


15

Lasting SentimentsWhat better way to dress-up a table than with an engraved vase! Because you hand make each vase, it will make the occasion even more special. The best part of this project is, it takes no longer than 10 minutes to etch!


Time to Complete: 15 minutes to assemble

Materials:• KraftyBlok™ Original (#425100)• Initial Stencils• Etching Cream (We tested

Armour™ (#5530)• Clear Glass Gems (#427271)• Flowers

Create Your Own StencilMaterials Checklist:• Craft Knife (#5536)• Heavy Clear Plastic• Printer & Paper• Firm surface

Instructions: 1. Clean the KraftyBlok™ with glass cleaner and a paper towel.2. Use a pre-cut last name initial stencil of the happy couple or create your own stencil by

following the directions below.3. Lay the KraftyBlok™ flat on your work area with the opening facing up and away from you.4. Place the stencil in the center of the KraftyBlok™ and tape it down. If it is a prepositional

stencil simply press into place. If you tend to be a messy painter, mask off the area around the stencil with painter’s tape.

5. Etch with Armour Etch® Glass Etching Cream, applying cream only to the stencil and avoiding edges. Wait 10 minutes.

DELPHIGLASS.COM


16

Lasting Sentiments 6. Place a small amount of

white paint on your finger tip and lightly rub over the stencil. This will make the etch appear brighter.

7. Fill with your favorite flower.

Create Your Own Stencil1. Choose a letter to

represent the initial of the last name. Next, select a font from a word processing program you have on your computer. Enlarge the font size until it is approximately 31/2" tall (our font was set at 350 point size but this will depend upon your font).

2. Print on a plain piece of paper (or sturdy printable transparency paper). If you are printing on plain paper, you will need a sheet of firm plastic. Place the plastic over the printed initial.

3. Place them both on a firm surface to cut the stencils, such as a double-layer of thick carton, a cutting board or other craft plank.

4. Tape the plastic and the design to each other and onto your cutting board.5. Using a sharp craft knife for the cutting. It’s easier to be successful if you use a

good sharp knife.6. Cut the initial into the plastic.7. When you’ve cut the entire design, check it over and smooth curves or edges as needed.8. You are now ready to use the stencil to etch. When applying stencil to glass block we used

a prepositional adhesive to hold in place.

DELPHIGLASS.COM


17

Frit Art Candle CubesDesign unique sand art style centerpieces to finish your table with a patriotic flourish.

Designed by: Julie Haan

Materials:• Rectangle KraftyBlok™

(#426113)• Star Bevel (#5278)• Silicone Adhesive (#5690)• Red Transparent Frit (#XF6113)• Cobalt Blue Opal Frit

(#B014782)• Clear (#B110101) or White Frit

(#XF1703)

Instructions: 1. Clean the KraftyBlok and

dry it completely.2. Pour frit in the color of your

choice into the KraftyBlok™ to create the first layer. Use a paint brush, length of dowel or other tool to gently spread frit as desired.

3. Carefully add a layer of frit in a contrasting color and position frit as before. Continue adding layers in alternating colors as desired.

4. If desired, use a paint brush handle, pencil or narrow dowel to push downward through layers to create downward plunges of color through contrasting bands.

5. Continue adding layers until the KraftyBlok™ is filled to within approximately ½" of the top.6. Use clear silicone adhesive to apply a star bevel to the outside of the KraftyBlok™ as a final

design embellishment.

DELPHIGLASS.COM


18

Holiday Snow BlockWho doesn’t love a snow globe? This is our rendition of a snow globe made with the KraftyBlok™ Mini, it’s truly a beautiful thing. Anyone would be happy to have this Holiday Snow Block in their living room.

Designed by: Jeanne Baruth


Time to Complete: 2 days

Project Tip:• Read all of the KraftyBlok™ Image Art instructions

before starting your project.• Large profile decals are fragile, handle with care.• This project requires the use of a laser printer,

not an inkjet.

Materials:• KraftyBlok™ Mini (#426112)• Image Art Paper (#425878)• 4" x 4" Holiday Image (pg. 19)• Large Glass Gem 11/4"• Glitter – Silver and Blue• Hot Glue Gun and Glue Sticks• White Glue• Ribbon – 1" wide, 30" in length• Paper Towels• Bowl for water• Scissors

Instructions: 1. Using the holiday image provided on pg 19 (or find a

favorite holiday image), copy it to any software on your computer that allows you to print images. Size the image to 4" x 4".

2. Set up your printer per the instructions on the Image Art.

3. Follow printers’ instructions and print transfer. Allow paper to set 10 to 15 minutes to dry. Trim to size with scissors.

4. Remove the stopper from the block and clean the thoroughly with glass cleaner. Place transfer in a bowl of water and wait approximately 1 minute or more until the decal starts to loosen slightly.

5. Lay the KraftyBlok™ flat on your work area with the opening at the top. Moisten the face of the block. Position the transfer above the surface; roll a ½" of the backing paper away from the top layer of the transfer (the decal). Line up the transfer with the top of the block. Take extra care when sliding the image as they are delicate and can tear easily. Gently slide the transfer from the backing paper onto the surface using a finger to smooth the decal as you peel away from the backing paper.

DELPHIGLASS.COM


19

Holiday Snow Block pattern. Size to fit KraftyBlok™ surface

6. Gently pat and smooth the transfer with a moist paper towel eliminating air pockets and wrinkles.

7. Allow to dry overnight.8. Once dry, permanently set the transfer by

preheating a conventional oven to 345°F. Place the tile on a baking rack with the transfer facing up. Bake for 15 minutes. Turn off oven, prop door open slightly, and allow the oven the tile to cool for 20 minutes. Remove from oven.

9. Lay the block decal side up. Apply white glue around the face of the block and apply silver glitter as shown in the photograph. A small amount of glue and glitter was added as accents to the image itself.

10. Once the glitter is dry, stand the block opening side up. Fill block with baby oil ½" from the top. Add 4 tablespoons each of both the blue and silver glitter to the oil.

11. Clean the block thoroughly of any oil or debris.12. Fit the stopper back into the opening.

Generously hot glue stopper in place and add large glass gem over the hole in the stopper to prevent the oil from leaking.

13. Wrap ribbon around the block and tie into a bow at the top. Tack ribbon in place using hot glue.

14. It is recommended that the block remains in an upright position at all times. A gentle shake will disperse the glitter in the block. DO NOT TURN UPSIDE DOWN.

Holiday Snow Block

DELPHIGLASS.COM


20

Chanukah LuminaryDesigned by: Glassy Ladies Studio


Time to Complete: 2 hours – Does not include dry time

Project Tip:• Wear safety glasses when using

glass-crafting tools.• Use a clear adhesive so the

Star of David glows.

Materials:• Original KraftyBlok™ (#425100)• 2 5 oz pkgs Jennifer’s Mosaics™ Blue • Cathedral Stained Glass Chips (#424361)• Contact Paper• Clear Mosaic Adhesive (#65106)• String of Lights or a Lightbulb with a 6' Cord• Craft Knife (#5536) or Scissors• Krylon® Frosted Glass Finish• 28" Length of Blue/Silver Ribbon• 6 Rhinestones

Instructions: 1. To protect work surface, cover with newspaper.2. Remove the labels and clean all surfaces of

the KraftyBlok™.3. Spray both sides of the KraftyBlok™ with Krylon® Frosted Glass Finish following the manufacturer’s instructions, allow to dry.4. While paint is drying, enlarge the pattern to fit the block surface.5. Place pattern on the work surface and tape down.6. Cut a piece of contact paper a little larger than the pattern. Remove the backing from the contact paper and place sticky

side up over the pattern, tape into position.7. Nip 3/4" blue cathedral stained glass chips in half and place them along the perimeter of the pattern to form the border.

Leave 1/8" between each piece.8. Randomly nip blue cathedral glass tiles into random shapes. Fit shapes like a jigsaw puzzle into the body of the star.

MOSAIC TIP: Never nip over the contact paper as it may cause the paper to become less tacky. For nipping instructions, visit our Creative Corner at www.DiamondTechCrafts.com.

9. When paint has dried, position the KraftyBlok™ on your work surface, with the 8" x 8" surface side up and the stopper opening facing down, towards you.

DELPHIGLASS.COM


21

Chanukah Luminary10. Apply mosaic adhesive to the

glass and place the mosaic, glass side down onto the surface of the KraftyBlok™. Allow mosaic to dry overnight.

11. When the glue has sufficiently dried (refer to manufacturer’s instructions), remove contact paper.

12. Using an adhesive apply one rhinestones between each of the points on the star.

13. Wrap a 28" ribbon around the side of the KraftyBlok™ and tuck the ends inside the opening and glue into place.

14. Place the light bulb or string of lights inside the KraftyBlok™ for a stunning holiday glow.

DELPHIGLASS.COM


22

Little Bloomin’ Night LightMosaics in a weekend – you betcha! This cute little floral nightlight is easy to create even for a beginner, simply nip, glue and grout!

Designed by: Rita Schwab


Time to Complete: 2 hours + dry time

Project Tip:• Cut stained glass chips over or into a bucket

or bowl to reduce straying shards.

Materials:• 1 Bag Stained Glass Chips (#424361)• White Grout (#425580)• KraftyBlok Mini (#426112)• Wheeled Glass Nippers (#2039)• Scissors• Mosaic Glue (#65105)• Disposable cup and plastic spoon• Paper Towels• Measuring Cup• Sponge or ScrubbyOptional: KraftyBlok Stand (#426121) and a single bulb with cord. Instructions:Step 1 - Preparation1. Cover work area with newspaper and place KraftyBlok Mini on top of newspaper. Position block so the stopper is at the bottom of the project.2. Make a copy of the pattern and place it nearby the project to use as a reference.Step 2 – Nip Glass1. Nip light green chips in half, and then nip each half once more lengthwise. This should create four thin rectangles which will be used for the

long blades of grass.2. Next, nip dark green chips in half, nip each piece in half again vertically to make four squares. These will be the shorter grass blades.3. Start at the bottom of the KraftyBlok and place the glass alternating different size chips. Leave at least 1/8" between glass pieces.

See pattern for placement suggestions.4. For flower stems, nip thin rectangles from a dark green chip. Remember irregular shaped glass is the hallmark of a mosaic; don’t worry about

cutting pieces exactly the same. Position stems on KraftyBlok™ and glue into place.5. To create the leaves use a Sharpie® marker and draw a leaf shape on a single chip. Nip away at the chip until you reach the outline of the leaf.

Position leaves on KraftyBlok™ and glue into place.

DELPHIGLASS.COM


23

Little Bloomin’ Night Light6. For the center of the flowers, use a marker and draw a small

¼" circle on three yellow chips. Use wheeled glass nippers and bite away at the edges of the glass until you reach the outline of the circle. Position at the top of each stem and glue into place.

7. For the flower pedals, measure and mark ¼" in from the corner of one side of a blue chip. Use a marker and draw a line from the ¼" mark to the opposite corner of the chip. Nip chip along the line. Repeat this process for all pink and blue flower pedals. Arrange pedals on block to form flowers and glue into place.

8. Fill in the area around the flowers and grass by randomly nipping white and dark blue chips. Leave 1/8" between all glass pieces, glue into position.

Step 3 – Grouting1. Measure 1/3 cup of White Grout following the manufacturer’s

directions. Add water a little bit at a time until it reaches a fudgy consistency.

2. Wearing a latex glove, spread grout on to the surface of the KraftyBlok™ making sure that grout is pressed into all the spaces between the glass pieces. Wait about 15 minutes for grout to set.

3. Gently wipe away excess grout using a scrubby, taking care not to pull away grout from between glass pieces. It is very important to remove any grout on tile surfaces before grout is completely dry.

4. Use a soft cloth to buff glass to a clean shine. Allow 24 hours for mosaic piece to dry thoroughly.

Step 4 – Lighting1. Remove the stopper from the bottom of the KraftyBlok™.

Use a scissors and cut a slit from the edge of the stopper to the center hole.

2. Insert a string of white holiday lights into the KraftyBlok™. Slide light cord through the slot to the center hole and position stopper back into place.

3. If using a KraftyBlok™ Stand, insert a single bulb with cord into the bottom of the stand and place finished project on to stand.

4. Plug in and enjoy!

Little Bloomin’ Night Light pattern. Size to fit KraftyBlok™ surface

DELPHIGLASS.COM


24

KraftyBlok™ Kaleidoscope LampProject Tip:MOSAIC TIPS:• Always use protective eye wear when nipping glass.• Opus (Latin for work) is the word used to describe the

way tiles are laid. The opus of a mosaic dictates the overall flow or movement of the mosaic.

• If your fingers are too big to maneuver small pieces of tesserae, use a pencil or tweezers to push them into tight fitting areas.

• Look for books on mosaics for inspiration.• To prevent glass from flying about, nip item inside a

bowl or pail. The sides of the container will prevent fly-away pieces.

Materials:• 1 KraftyBlok (#425100)• 1 package each 5 oz ¾" Cathedral Glass Squares

– Purple (#426274), Dark Green (#425130) and Blue (#425122)

• 13 Blue ¾" Glass Gems, 9 White ¾" Glass Gems, 1 White 1½" Glass Gem, 1 Blue ½" Glass Gem (included in #427271)

• Clear Silicone (adhesive) (#5690)• 1 String of White Christmas Lights• Mosaic Wheeled Glass Nippers (#2039)• Safety Glasses (#5163)

Instructions:Step 1 - Preparation1. Completely read the directions before starting.2. Cover your work area with newspaper to protect work

surface.3. Collect and place all supplies needed on your work surface.Step 2 – Glass Placement1. Clean the KraftyBlok™ with glass cleaner or a 50/50 solution of vinegar and water. Dry completely with cloth.2. Place the KraftyBlok™ in a horizontal position on newspaper. Slide pattern underneath block as a guide for placement of glass. It is not recommend-

ed to trace the pattern onto the glass as marks may show through.3. Begin by placing glue on the back of 1½" white gem. Adhere to the KraftyBlok™ where indicated on the pattern. Continue by gluing ¾" blue and

white gems, alternating colors around the central gem. Next, apply glue to the back of the ¾" blue and white gems. Adhere to the corners where indicated on pattern. Finish by gluing a ½" blue gem centered and on top of the white gem.

4. Apply adhesive to the back of a dark green cathedral square. Starting in the lower right corner of the KraftyBlok™ secure in place where indicated. Continue to add the dark green squares to form a circle around the gems. Continue this process with both blue and purple cathedral glass squares.

DELPHIGLASS.COM


25

KraftyBlok™ Kaleidoscope Lamp 5. Nip ¾" Green, Blue and Purple glass

squares into smaller pieces. Glue in place to fill the voids between glass squares.

6. When the front has dried, place the KraftyBlok™ on its side with the opening facing up. Starting at the left of the hole glue two rows of ¾" purple chips side by side leaving approximately 1/8" between each piece, until you reach the edge. Allow to dry. Rotate KraftyBlok™ to the right . Glue two more evenly spaced rows of purple cathedral glass squares. Allow to dry. Continue placing two rows of purple glass squares across the side.

7. Rotate block back on its side with the opening facing up. Glue four blue cathedral glass squares to the right of the opening in two rows leaving 1/8" between each piece. Finish the side by adding two green glass squares. Allow to dry.

8. Rotate block to the left. Glue eight dark green glass squares into two rows, 1/8" apart. Add two blue squares on either side of the dark green squares and finish the double rows of glass squares with four purple squares. Glue into place and allow to dry.

9. To finish corners, nip a chip in half, forming two rectangles, and apply pieces to the corner curves.

10. I insert string of white Christmas lights in the block and allow plug to extend out. Plug-in and enjoy!

LEGENDB = Blue W = White P =Purple

KraftyBlok™ Kaleidoscope Lamp pattern.Size to fit KraftyBlok™ surface

DELPHIGLASS.COM


26

Spa Day BankSave money in style with this scrapbook bank. Scrapbooking is fun for crafters of all ages.

Designed by: Morgan Baruth

Project Tip:Cut, embellish & lay out your design on your work surface first. Once you are happy with your design, adhere together, and then glue all panels to your KraftyBlok™.

Materials:• KraftyBlok™ (#425100)Embellishments:• Primas™ – pre-punched assorted flowers• Brads with rhinestones• Rhinestones with self adhesive backsStamps:• Stampin’Up™! Bubble Queen Set, alphabet and single flowerPaper:• Stampin’Up™! Petals & Paisleys Reversible Stripes/dots/

paisley/flowers• Solid card stock in light pink, olive green & aquaTools:• Paper Trimmer • Black Ink Pad• Scissors • Hole Punch• Colored PencilsAdhesive:• Elmer’s spray adhesive• Glue Stick• 3D foam blocks

Instructions:SPA FUND BANK – FRONT1. From a 12" x 12" piece of paisley paper cut a 6¾" x 6¾" square to cover the front of the KraftyBlok™.2. Next cut a 6½" x 6½" square of aqua card stock and center it on top of the paisley paper, glue into place.3. Cut a 2¾" x 6½" strip of pink polka-dot paper and place 7/8" down from the top of the aqua paper, glue into place.4. Cut ½" x 6½" and ½" x 2" strips of the multi-colored striped paper. Arrange shorter strip at the top of the pink polka-dot paper and the longer strip at

the bottom, glue into place. Use image for placement.5. Using a hole punch, create three circles out of the multi-colored striped paper. Place circles next to the shorter strip.6. Cut a 1½" x 2" rectangle from the striped paper. Stamp with “find joy in the little things.” Glue to an olive green tag and embellish tag with a light blue

grosgrain ribbon and a pink rhinestone brad. Affix to the top corner of the design layout.

DELPHIGLASS.COM


27

Spa Day Bank7. Stamp a piece of pink card stock with the “Bubble Queen”

stamp. Using colored pencils lightly color the stamped image. Cut around the perimeter of the stamp leaving a ¼" border. Glue pink stamped paper on top of olive green card stock and glue. Cut around the perimeter of the pink leaving about a ¼" border. Angle and glue to the bottom of the design layout.

8. Stamp or free-hand the words “Spa Day Fund” on the pink polka-dotted paper.

9. Finish the front by stamping a flower in the upper left and lower right hand corners of the design layout.

10. Finish by embellishing with punched flowers and rhinestone brads.

SPA FUND BANK – SIDES & TOP1. Cut two 10" x 1¾" strips (side panels) from the pink flower

paper and two 2½" x 1¾" strips (top panel) from the multi- colored striped paper. These will act as the side and top panels for the bank.

2. Cut one 7¾" x 1¾" strip of aqua card stock and one 7¾" x 1¾" strip of olive green card stock. Place smaller strips on top of the larger strips and glue into place. Embellish with punched flowers and brads.

3. Use foam 3D blocks to add dimension to the flowers.MOUNTING PANELS TO THE KRAFTYBLOK™1. Cover crafting area with newspaper. When working with spray

adhesive make sure the area is well ventilated.2. Place the KraftyBlok™ on top of newspaper with stopper-top

opening facing up.3. Using spray adhesive spray the back of the front panel.

Place front panel on the face of the KaftyBlok™, press gently to secure.

4. Spray the backs of the top and side panels in the same fashion and press into place.

DELPHIGLASS.COM


28

Cute as a Button CanisterFind a sweet home for your wayward buttons in this “Cute as a Button” canister. Simple to create, it’s not only a cleaver button container; it doubles as a pin cushion! It’s a sweet gift for anyone.

Designed by: Morgan Baruth


Time to Complete: 2 hours

Materials:• KraftyBlok™ 4" x 8" Rectangle (#426113)• Glue Sticks• Hot Glue Gun• DCWV, “The Stacks” Scrapbooking Paper• 4 Small Wooden Spools• Ultra Fine Green Glitter• Safety Pin• One 3" x 3" & one 1½" x 1½" circle of cotton fabric• 6 Cotton Balls – large• 6 Assorted and 4 matching flat Buttons for embellishing• 2 Pearl Sewing Pins• 1 Sewing Needle, Threaded• 1 Small Plastic or Cloth Measuring Tape• E6000® Glue (#8919)• “A Thing of Beauty” stamps - Stampin’ Up!• Staz On, Black Permanent Ink - Stampin’ Up!• 1" Circle Punch - Stampin’ Up!• Stampin’ Pastels – Stampin’ Up!Note: To purchase Stampin’ Up! Products Contact [email protected] or your local dealer.

Instructions:1. Clean the KraftyBlok™ with glass cleaner and a lint free cloth. Remove the plastic plug and sit it upright on your work surface so the opening is

facing up.2. Using “A Thing of Beauty” stamp pack, stamp the bonnet, boot, tea cup, hat and hat box combo onto card stock. Use the Stampin’ pastels to add

color to the images. Apply glue and sprinkle with glitter to areas you would like to highlight. Using scissors cut away the image from the cardstock leaving a 1/8" border around each image.

3. Cut the following: Button & Polk A Dot paper: two 21/8" x 9¼" strips (side panel) Olive Green Solid Paper: one 3" x 3" square with a 2" circle cut out of the middle (top panel), one 23/4" x 6¾" (back panel)

4. Punch two 1" circles (front embellishments)5. Affix the large stamp cut-out 3" down from the top of the back paper panel with small mounting tabs. Hot glue a flat button to each corner of this

panel. Apply a dot of hot glue to the face of each button and press paper panel against the back surface of the KraftyBlok™. When finished, you should be able to see the stamped image through the front surface of the glass block.

DELPHIGLASS.COM


29

6. For the side panels (button and polka dot paper), fold over one edge of the paper strip ½" and the opposite edge 2". Place paper so that the 2" fold is at the bottom of the block and hot glue into position along one side of the KraftyBlok™, making sure the paper is taunt as you glue into place. Repeat this process on the opposite side.

6. Hot glue the top panel with the 2" opening to the top of the KraftyBlok™7. Hot glue 4 wooden spools to the bottom of the block to create feet.8. Next, hot glue the bonnet cut-out, a 1" green dot and safety pin into a cluster. Use E6000® to glue it in the upper left corner of the block front.9. Hot glue the boot cut-out and 1" green dot together and affix them to the bottom right front using E6000®.10. Glue clusters of 3 or so buttons to the top right and bottom left of the block front using E6000®.11. To affix the measuring tape to the top of the block, start with a 5" tail. Hot glue tape at the 5" mark to the front left corner. Stretch tape

across the top of the block to the opposite corner, create a miter fold and hot glue into place. Continue this process until you have reached your starting point. Tie a flat bow with the remainder of the measuring tape and secure in place with E6000® to the front left corner.

12. Using ink specially formulated for stamping on glass, stamp the words “A Thing of Beauty is a Joy Forever” to the front of the KraftyBlok™, 4" down from the top edge.

13. To create the Pin Cushion lid, place a 3" x 3" fabric square print side down on your work surface. Fill the center of the KraftyBlok™ lid with cotton balls or fiberfill. Place lid filling-side down on top of the fabric and pull the edges of the fabric around to the flat side of the lid, hot glue into place. To cover raw edges, glue a 1½" fabric circle to the bottom of the stopper. Insert stopper back into the opening at the top of the KraftyBlok™ and stick a few pins and needle into the cushion.

14. Fill with buttons!

Cute as a Button Canister

DELPHIGLASS.COM


30

Decoupage BankMotivate yourself to save money with this Decoupage Bank. Decoupage is fun for crafters of all ages.

Materials:• 1 KraftyBlok™ (#425100)• 1 16 oz or smaller bottle of Plaid’s Mod Podge™ Gloss Lustre Water base sealer• 1" wide foam or latex paint brush• White copy paper and access to color copier (optional)• Paper currency (U.S. or Foreign) in different denominations• Newspaper or craft paper to protect work surface• 6" x 10" black foam core for name plate • Assorted coins • Scissors• Glass cleaner • Paper towel • Craft knife (#5536) • Ruler • Craft glue

Instructions:Step 1 – Material Preparation1. Completely read the directions before starting.2. Cover your work area with newspaper to protect work surface.3. Collect and place all supplies needed on your work surface.Step 2 –Paper Preparation1. Clean the KraftyBlok™ with a glass cleaner. Dry completely with paper towel.2. Make color copies of a variety of different bills. Include foreign currency for added interest. Place several bills together on the copier to maximize the

number of copies per sheet of paper. You may copy just the front of the bills or both front and back for variety.3. Cut your copies to actual size of individual bills.Step 3 – Decoupage “Collage” Process1. Begin by placing the back of the block flat on the work surface with the opening at the top. Brush a thin coating of glue to an area on the front of the

KraftyBlok™, slightly larger than a bill you wish to glue. Place the bill at an angled position (for interest) on the block. Brush over the entire surface of the bill with more glue, pushing out any air bubbles until the bill is smoothly glued in place.

2. Using another bill or special portion of a cut bill, continue to add more currency to the front face of your KraftyBlok™ as instructed above. As you work to the sides, start wrapping the currency around the edges of the KraftyBlok™. Overlapping ensures the surface is completely covered.

3. The corners of the KraftyBlok™ may be difficult to wrap. Continue to Mod Podge™ and place bills so that they cover right up to the corners. Small pieces of bills can be added to cover any exposed areas if needed.

4. Once the entire front face is decoupaged, let it dry for 30 minutes before decoupaging the back.5. Decoupage back and visible sides following steps 1-4.

NOTE - You may wish to leave the bottom of the bank clear or create a clear window on one of the sides so you can see how much “real” money is being saved!

6. To decoupage the top, remove the stopper. Continue to add pieces of currency, overlapping the opening if necessary. Once the top has been completed, use a craft knife to cut the paper completely around the stopper opening so you have a clean, neat hole for the stopper.

7. Allow to dry 24 hours before adding the name plate and coin embellishments.Step 4 – Name Plate & Embellishments1. To personalize your bank, use Word Art, cut-out letters, stencils or even hand draw your special name plate (“College Fund”, “Fun Money”,

“Gas Money”) on a piece of paper approximately 5"-6" across and 1½" tall. Using a ruler and scissors, cut out this rectangle. Cut a piece of the black foam core board the same size, using a craft knife. Glue the name plate to the foam core and let dry. The foam core adds depth and dimension to the surface.

2. Position your personalized name plate on the bank front and glue in place. Glue coin embellishments if desired into place. Viola, your customized bank is ready!

DELPHIGLASS.COM


31

Silly Billy The SnowmanThis snowman is a frosty treat for the eyes. He lights up any room with his whimsical smile. Use him as a centerpiece, lamp, or a mantle decoration.



Time to Complete: 1 day

Materials:• 1 KraftyBlok™ (#425100)• 1 KraftyBlok™ Mini (#426112)• 1 KraftyBlok™ Rectangle (#426113)• 1 Deco Tile• Snow-Tex®

• Clear Pearl Glaze• Wired Garland• Phillips LED Cool White battery operated Snowflake Lights• Googly Eyes• Sculpty Clay – orange• 18" Doll knitted cap, gloves and scarf• Large cotton ball (snowball)• Red Buttons – Three 11/2"• Tree Branch – 1/2" diameter

Instructions:1. Completely read the directions before starting. Cover your work area with newspaper

to protect work surface. Collect and place all supplies needed on your work surface.2. Clean the KraftyBlok™ with a glass cleaner or a 50/50 solution of vinegar and water. Dry completely with paper towel.3. Remove the stoppers and place the KraftyBloks™ opening down on work surface. Apply Snow-Tex® on all sides of the KraftyBlok™, per the

manufacturer’s instruction. Snow-Tex® dries permanently in 2-3 hours. Heavier application may require a slightly longer drying time.4. In a well-ventilated area, spray the KraftyBloks™ with a pearl glaze. Allow them to dry according to the manufacturer’s instruction.5. Pull a doll-sized knitted hat over the top of the Rectangle KraftyBlok™ opposite the opening. Lay block flat and position facial features (eyes and

smile) to the block, hot glue in place. Shape the orange clay into a carrot-like shape. Push securely onto the block creating a nose.6. Place the KraftyBlok™ Mini on the work surface with the opening facing down. Cut the end of each wooden stick (arms) at an angle. Mix epoxy

according to the manufacturer’s instruction. Apply epoxy to each end of each cut stick and to the sides of the KraftyBlok™ Mini and into position. Hold with tape until dry.

7. Stand the large KraftyBlok™ on the table and position the battery pack from the light strand on the table behind it. Place the KraftBlok™ Mini on top of the large KraftyBlok™ with the opening facing down. Tilt block and insert two lights inside the opening. Place the Rectangle KraftyBlok™ on top of the KraftyBlok™ Mini, opening down. Insert two lights into the block. String the remaining light onto the front of the snowman. Place a mitten on each branch and drape wired garland between each mitten hand. Wrap remaining light strand around garland.

8. Glue buttons, snowball, gloves and scarf into place. Light your snowman and enjoy the not-so-frosty glow.

DELPHIGLASS.COM


32

Let It Snow LightboxDesigned by: Grace Santoro


Time to Complete: 30 minutes

Project Tip:For a Chanukah lightbox, use white lights, blue garland and a blue and white wired ribbon. Use glass paints and/or pens to write “Happy Chanukah” or to draw 9 colorful candles on the front of the KraftyBlok™.

Materials:• 1 Rectangle KraftyBlok™ (#426113)• 1 2 oz DecoArt Twinkles Writer

(UPC6621802771)• Merry Minis 8 pc 1" Glitter Snowflakes

(UPC2100189103)• 1 Celebrate It Holiday Ribbon

(UPC0010064044)• 1 String of holiday lights (50 strand),

white or clear• 1 2 ft section of red garland• Aleene’s Tacky Glue (UPC1775415603)• Hot glue gun and glue sticks

Instructions:1. Remove the labels from the KraftyBlok™ and clean all surfaces of the glass. Dry thoroughly.2. Place the KraftyBlok™ on a work surface with the 4" x 8 side facing up. Use a glitter paint writer to create a special holiday message lengthwise on

the side of the KraftyBlok™. Allow to dry following manufacturer’s instructions.3. While paint is drying, remove the hanging threads from Merry Minis Glitter Snowflake ornaments. Use glue to ahere the snowflakes randomly to the

front surface of the KraftyBlok™ making sure you do not cover the words.4. One the paint and glue have dried, remove the stopper from the KraftyBlok™ and insert a string of 50 tree lights into the cavity of the block.5. Use scissors and cut a slit from the edge to the center hole of the cap. Insert the light cord through the slit and slide the cord to the center hole.6. For a festive look, insert a 2 ft piece of red garland into the KraftyBlok™ cavity so it appears behind your special holiday message.7. Next, wrap a length of wired ribbon around the outer perimeter of the KraftyBlok™ and use a glue gun to tack into place. Next, create a multi-looped

bow and hot glue it to the top of the KraftyBlok™ to cover the ends of the ribbon.

DELPHIGLASS.COM


33

“Remember When” BankDesigned by: Jeanne Baruth


Time to Complete: 1 hour to assemble. Allow transfers to dry overnight

Materials:• KraftyBlok™ Mini (#426112) • Image Art Paper (#425878) • White sheet glass (#S20091W)• Small pieces of jewelry, keys, bottle caps, charms, vintage belt buckle, small

squares of mirror, found treasures to use as components. Use similar color themes and genres.

• 20" each of 2" and ½" coordinated ribbon• Wooden Candle Cup 15/8" – 4 (feet)• Gold Spray Paint • Gold Glitter and white or spay glue – optional• Hot Glue Gun • E6000® adhesive (#8919)• Paper Towels • Bowl for water • Scissors

Instructions:1. Find your picture and copy it to any software on your

computer that allows you to manipulate and print images. Change the color setting to sepia. Size the picture to 2" x 6". Cut the image into three 2" x 2" squares. If you have bottle caps, a locket or simply an area you wish to add an additional photo. Measure the area and print similar images to size to accent the larger image.

2. Set up your printer per the instructions on the Image Art packaging.3. Follow printers’ instructions and print transfer. Allow paper to set 10 to 15 minutes to dry.4. Measure and cut three 17/8" x 17/8" squares of white sheet glass (#S20091W). For glass, cutting instructions visit our “Creative Corner” at

www.diamondtechcrafts.com. Clean the glass with water and a clean lint free cloth.5. Place one of the three transfers in a bowl of water and wait approximately 30 seconds.6. On one of the glass squares, line up one of the Image Art transfers. Take care when sliding the image as they are delicate and can tear. The image

is slightly larger than the glass, which allows the image to be wrapped over the edge of the glass square. Gently slide the Image Art transfer from the backing paper onto the surface using a finger to smooth the decal as you peel away from the backing paper.

7. Gently pat and smooth the Image Art transfer from the center out with a moist paper towel eliminating any air pockets and wrinkles. Repeat steps 6 and 7 on the two remaining white pieces of glass.

8. Allow to dry overnight.9. Once dry make the decals more scratch resistant by preheating an oven to 345°F. Place 3 pieces of glass on an oven safe rack or baking sheet with

the decal facing up. Bake for 15 minutes. Turn off oven. Prop door open slightly and leave in the oven for 20 minutes. Remove with heat safe oven mitts or pad.

10. Set the KraftyBlok™ with the opening facing up on the work surface. Fold one end of the one inch ribbon under ½" and glue it next to the opening. Wrap the ribbon around the block and fold the remaining end under ½" and glue it next to the opening. Repeat this process with the ½" ribbon over the 1" ribbon.

11. Using E6000®, glue a vintage belt buckle over the opening.12. Use the photo for inspiration; glue the white glass with the images down the middle of the KraftyBlok™. Continue to embellish the face of the

KraftyBlok™ until the desired look has been reached.13. Spray paint the wooden candle cups gold and allow to dry. Use E6000® to glue the feet to the bottom of the KraftyBlok™.

DELPHIGLASS.COM


34

Nest Egg BankWho would not want to put money in this adorable nest egg bank? Watching your savings grow through this cute glass block couldn’t make saving easier.

Designed by: “The Diamond Tech Team”


Time to Complete: 2 days

Project Tip:• Read all of the KraftyBlok™ Image Art instructions before starting your project.• Large profile decals are fragile, handle with care.• This project requires the use of a laser printer, not an inkjet.

Materials:• KraftyBlok™ Mini (#426112)• Image Art Paper (#425878)• Nest on a Branch• Small Flocked Speckled Eggs• Small Glass Bird Ornament• 20" each of 1" and ½" Coordinating Ribbon• Hot Glue Gun and Glue• Paper Towels• Bowl for water• Scissors

Instructions:1. Find your nest egg picture and copy it to any software on your computer that

allows you to print images. Size the picture to 4" x 4".2. Set up your printer per the instructions on the Image Art.3. Follow printers’ instructions and print transfer. Allow paper to set 10 to 15 minutes to dry.

Trim to size with scissors.4. Place transfer in a bowl of water and wait approximately 1 minute.5. Lay the KraftyBlok™ flat on your work area with the opening at the top. Moisten the face of the block. Position the transfer above the surface; roll a

½" of the backing paper away from the top layer of the Image Art transfer (the decal). Line up the Image Art transfer on the surface. Take extra care when sliding the image as they are delicate and can tear easily. Gently slide the Image Art transfer from the backing paper onto the surface using a finger to smooth the decal as you peel away from the backing paper.

6. Gently pat and smooth the Image Art transfer with a moist paper towel eliminating air pockets and wrinkles.7. Allow to dry over night.8. Use a clear acrylic sealer specifically made for sealing decals onto glass. Mask off around the transfer; this will prevent overspray from getting on the

rest of your project.9. Spray the sealer according to the manufacturer’s directions and allow it to dry.10. Glue the eggs and the glass bird into the nest. Remove the plastic stopper from the KraftyBlok™ and set it on the work surface. Glue the nest to the

stopper.11. Fold the 1" ribbon over ½" and glue it next to the opening. Wrap the ribbon around the block and fold the other end under ½" and glue it next to the

hole. Repeat this process with the ½" ribbon over the 1" ribbon.12. Put the stopper back on top of the block and your bank is complete.

DELPHIGLASS.COM


35

Night Before Christmas Victorian SceneDesigned by: Diana Duvall


Time to Complete: 1 hour

Project Tip:• Read all of the Image Art instructions

before starting your project.• Large profile decals are fragile,

handle with care.• This project requires the use of a laser printer,

not an inkjet.

Materials:• 1 6" x 6" KraftyBlok™ (#426112)• 1 KraftyBlok™ Mini Stand (#426120)• 1 Small Needle Pine Tree (UPC-2816244083)

Lemax• 2 Christmas Harmony Figurines-Carolers

(UPC2816272403) Lemax• 2 lb Bag Decorative Sand White

(UPC - 9343273050) Panacea Products• 1 Spool Wired Edge Ribbon Plaid

(UPC-0010063911) Michaels Stores, Inc.• Aleen’s All Purpose Tacky Glue• 4"- 6" Tweezers (#62602)• Photo of “Night Before Christmas” by

Thomas Kinkade (pg 38), or personalize with any Christmas card image)

• Glass Cleaner and paper towel

Night Before Christmas Victorian Scene Instructions:1. Remove the labels from the KraftyBlok™.

Clean all surfaces with glass cleaner and dry with a paper towel.

2. Remove the plastic stopper, measure 3/4 cup of white sand and pour into the KraftyBlok™ cavity.

3. Using tweezers, carefully lower the pine tree into the KraftyBlok™ and position it to the left side of the block. It may be easier to put it through the opening point first and then turn it upright. Try to cover the base with sand to stabilize it.

4. Next, insert the male Victorian Caroler centering him inside the KraftyBlok™. Place the female Victorian Caroler to the right of the male Caroler so she is positioned across from the pine tree. Adjust the objects for balance. Cover each figurine’s base with sand to secure in place.

5. Use a scissors and cut out the image at right (or supply your own). If choosing to use your own image, cut to a 51/2" x 51/2" size. Place the image on the backside of the KraftyBlok™ so that it appears to be behind the Carolers. If using the Kinkade image, try to place the figurines so they are on either side of the lamp post.

6. When satisfied with placement, add a small dot of glue to the front four corners of the image. Press image up against the back of the KraftyBlok™ so the scene is visible through the front. Hold in place until the glue is set.

7. Replace stopper and wrap a wired ribbon around perimeter of the KraftyBlok™. Bring the ends of the ribbon up and tie them into a bow.

8. Slide the finished KraftyBlok™ into the stand and you are finished with this adorable snowy holiday vignette.

DELPHIGLASS.COM


36

Cut out image along black outline

DELPHIGLASS.COM


37

The First Noel!Noel, Noel, by the light of that same star, three wise men came from country far...The word comes from the French word Noël meaning “Christmas”, which drives from the Old French word noël, a variant of nael. The Latin origin is the word natalis, (birth).




Project Tip:• Carefully read all product instructions before starting your project.

Materials:• 3 KraftyBlok™ Minis (#426112)• 1 KraftyBlok™ Rectangle (#426113)• Armour Etch® (#5530)• Gold Leaf Kit (#165010)• Mini Lights – 100 count white lights with a white cord• Hot Glue Gun & Glue Sticks• Holiday Ribbon 21/2" wide x 8 ft long• Red Glitter Paint or Red Glitter and Glue• Artificial Flora and/or Bird• Paint or Foam Brushes• Scissors

Instructions:1. Cover your work area with newspaper to protect work surface.

Collect and place all supplies needed on your work surface.2. Clean the KraftyBlok™ with glass cleaner or a 50/50 solution of

vinegar and water. Dry completely with cloth. 3. Remove the stoppers and place the KraftyBloks™ on newspaper with the openings

facing down. Work in a well ventilated area and wear safety glasses and rubber gloves to apply and remove etching cream to the front and back faces of the KraftyBloks™. Follow all manufacturer’s instructions. Do not etch the outer edges of the front and back faces (Fig. 1). This process may need to be repeated several times to achieve a consistent etch. Use glass cleaner or vinegar solution to remove etching cream residue. Dry the KraftyBloks™ using lint-free cloth.

4. Choose your favorite font from a word processing program. Enlarge it to fit the face of the KraftyBloks™. Print and cut out your letters and trace them onto the glass with a silver Sharpie® . Fill in the letters with glitter paint or glue with sprinkled glitter. Allow the letters to dry.

5. Following the manufacturer’s instruction, apply gold leaf to the front edges of the KraftyBloks™ (Fig.1)6. Fold the raw edges of a holiday ribbon under 1/4" and tack in place with hot glue. This will create a finished end. Place the edge of the

ribbon on one side of the block opening and tack in place with hot glue. Gently wrap the ribbon around the perimeter of the block using small dots of glue on the rib of the block to hold ribbon in place. Cut a fold the remaining end of the ribbon 1/4" and glue in place leaving the opening free of the ribbon. Repeat of the remaining three blocks.

7. Divide the lights equally into 4 groups; insert one group of light strands into each KraftyBlok™ opening.8. Adorn the decorative KraftyBloks™ with artificial flora and/or birds to complete this festive project.

Edges – do not frost

Face – frost front and back sides

Fig. 1

Painted KraftyBlok™ Designed by: Dayton Allen

Skill Level: (Adult 1-5: 1 being the easiest, 5 being most difficult) The skill level and time to complete will vary depending on the picture you choose to paint.


Project Tip:• Clean and dry the KraftyBlok™ very well prior

to applying the paint.

Materials:• KraftyBlok™ Original (#425100)• Assorted Acrylic Paints• Assorted Paint Brushes• Paint Pallet• Water Cup• Glass Cleaner• Paper Towels• Painter’s Tape• Matte Acrylic Fixative Spray

Instructions:1. Completely read these directions before starting.

Cover your work area with newspaper to protect work surface. Collect and place all supplies needed on your work surface.

2. Clean the KraftyBlok™ with a glass cleaner. Dry completely with paper towel.

3. Chose an image you wish to paint on the block. For inspiration, use a photograph, an illustration, or your own creative idea.

4. Select the acrylic paint colors necessary to paint your chosen image. Craft acrylics are affordable and come in a large variety of colors.

5. Have your brushes cleaned and ready – have your water cup filled in order to clean brushes while painting.6. Use painter’s tape and mask off the paintable area of your KraftyBlok™. This will create a clean, crisp border separating your painted

area from the rest of the glass block.7. Remember you are painting on glass, a non-porus surface. Therefore, paint will not be absorbed. As a result, you will need to paint in

layers and allow sufficient time for each layer to dry. Use water a bit more sparingly when painting on glass, too much water and the base, layers will begin to breakdown. There is no one basic rule to painting – everyone has his or her own style. Have fun!

8. When finished, allow to dry 24 hrs.9. Follow manufacturer’s instructions. Seal your masterpiece with a matte finish, acrylic fixative spray. Allow to dry. Carefully and slowly,

remove the painter’s tape from the KraftyBlok™ surface, making sure not to remove parts of your painting.10. Clean and polish your painted block and display!

DELPHIGLASS.COM


38

Christmas Tree Accent Light This contemporary holiday accent light is the perfect adornment for your mantle, side table or buffet, casting a subtle glow on your celebrations.

Designed by: Diana Duvall

Time to Complete: 11/2 hours

Materials:• KraftyBlok™ Original (#425100)• KraftyBlok™ Large Stand (#426121)• System 96® Glass Pebbles - Medium Green (#XP121)• System 96® Glass Pebbles - Red Striker (#XP151)• System 96® Glass Pebbles - Medium Amber (#XP1108)• 100 Count Strand Christmas Lights Clear Bulbs with White cord

(if not available use clear with green cord)• E6000® Clear Adhesive (#8919)• Ruler• Sharpie® Marker• Plastic Knife or craft stick• Glass cleaner and paper towel

Instructions:1. Gather all materials.2. Remove the labels from the KraftyBlok™ and clean all surfaces

of the glass; dry thoroughly.3. Position the KraftyBlok™ on a work surface, with the

71/2" x 71/2" surface side up and the stopper opening facing down towards you.

4. With ruler and marker, make a small mark at the center top and bottom of the block. This represents the center line and starting point for aligning the glass gems.

5. Use the photo as a guide and place a green gem on the surface of the block directly under the top center mark (within ¼" from top edge of glass). Spread a thin layer of glue over the flat surface of the gem and press firmly into position.

6. To complete row 1, place 4 red gems on either side of the green centered gem and glue into place. Use a ruler to insure the gems are level and straight.

7. Row 2 – Position and glue 2 green gems directly under the top centered green gem. Position and glue 3 red gems on both sides of the green gems, once again checking with a ruler to insure they are level and straight.

8. Row 3 – Position and glue a green gem directly in the center and under the previous two. Place two more green gems on either side. Finish row by adding 3 red gems on both sides. The outer edge will be staggered.

9. Row 4 – Position and glue 4 green gems centered directly under the 3 previous green gems. Add 2 red on either side to complete row 4.10. Row 5 – Center and adhere 5 green gems under the last row and finish with 2 red gems on both sides. Keep checking your center line and

distance from the top on each side to ensure row evenness.

DELPHIGLASS.COM


39

Christmas Tree Accent Light 11. Row 6 – Center and adhere 6 green

gems and finish with 2 red gems on each side.

12. Row 7 – Center and adhere 7 green gems and only 1 red gem on each side.

13. Row 8 – Center and adhere 8 green gems. No red gems are added to the bottom row.

14. For the tree trunk, adhere 6 amber gems in 3 rows of 2, centered directly under the tree (green gems). If you can not fit 3 rows, just add 2. Position and glue 4 red gems on both sides of the amber gems. There should be enough room on the bottom to position a final row of red, directly under the row above. This row will not be staggered. Allow glue to thoroughly dry before inserting lights.

15. Light Assembly – Remove the plastic stopper and insert a strand of 100 lights into the cavity of the KraftyBlok™. If lights are new, stretch the wires to straighten before placing inside the KraftyBlok™. If needed, using a ruler to move the lights around inside the block to evenly distribute. The KraftyBlok™ will be completely filled with the 100 light strand.

16. Use a scissors and cut a slit from the edge to the center hole of the KraftyBlok™ cap. Insert the light cord through the slit and slide the cord to the center hole. Insert the cap back into the KraftyBlok™ opening.

17. Slide the finished KraftyBlok™ into the stand and thread the light cord through the opening in the bottom of the KraftyBlok™ Stand. Plug into an electrical outlet and enjoy this cheerful holiday accent light.

DELPHIGLASS.COM


40

DELPHIGLASS.COM


41

Oriental GardenThis contemporary holiday accent light is the perfect adornment for your mantle, side table or buffet, casting a subtle glow on your celebrations.



Time to Complete: 3 hours (does not include drying or baking time)

Project Tip:• Read all of the Image Art™ instructions before starting your project.• This project requires the use of a LASER PRINTER.

Materials:• Laser Color Printer• KraftyBlok™ Original (#425100)• Image Art™ Paper (#425878)• Garden Image (at right)• Lint Free Cloth or Paper Towels• Bowl for water• Scissors• Small Pebbles• Potting Soil• Long Tweezers (#45151) or Chop Sticks• Assorted Plants• Glass Cleaner

Instructions:1. Copy and resize the image to 6" x 6" using any software that allows you to

manipulate and print images.2. Set up your printer per the instructions on the Image Art™ packaging.3. Follow printers’ instructions and print transfer. Allow transfer to set 10 to 15

minutes to dry, trim decal to size.4. Remove the stopper from your KraftyBlok™, clean with glass cleaner and a

lint-free cloth.5. Place transfer in a bowl of water and wait approximately 1 minute.6. Lay the KraftyBlok™ flat on your work area with the opening at the top. Slightly

moisten the face of the block. Position the transfer above the surface; roll a 1/2" of the backing paper away from the top layer of the Image Art™ transfer (the decal). Line up the Image Art™ transfer on the surface. Take extra care when sliding the image as they are delicate and can tear. Gently slide the Image Art™ transfer from the backing paper onto the surface. Use your fingers to smooth the transfer as you peel away from the backing paper.

7. Gently pat and smooth the Image Art™ transfer with a moist paper towel, eliminating air pockets and wrinkles.

Oriental Garden8. Allow to dry 2 hours.9. To permanently set the transfer, preheat conventional oven to

345°F. Place the KraftyBlok™ on a baking rack Image Art transfer up. Bake for 15 minutes. Turn off oven, prop door slightly, and allow to rest for 20 minutes.

10. Remove with hot mitts and let the block completely cool.11. Hand wash using water, dry with a lint-free cloth.12. Pour approximately 1/2" of small pebbles into the block for

drainage. Fill to proper height with a good draining potting soil. Insert small plants with long tweezers or chop sticks. Water lightly (3 or 4 ounces).

13. Neglect It! Water lightly only after it gets dry once every few weeks, depending on conditions. NEVER OVERWATER! Place in a bright area, but not in direct sunlight. You should have enough light to read by. When plant gets as big as you want, pinch off the newest growth to encourage bushier growth. Then enjoy!

Try adding embellishments as shown in the photo. The Oriental Garden is a delicate balance between earth and water. This peaceful garden includes an authentic Geisha on white fused glass. Fused glass dichroic rounds are used to represent gazing globes. Giving this oriental garden that Feng Shui feel of the “perfect spot” to view beauty and relax. See Fuseworks™ Orient Decals and fusing glass on www.diamondtechcrafts .com.

DELPHIGLASS.COM


42

DELPHIGLASS.COM


43

Summer Song BirdsDesigned by: Karen Embry


Time to Complete: 1 hour (does not include drying or baking time)

Project Tip:• Paint in a well ventilated area and follow the

manufacturer’s instruction.• Clean and dry the KraftyBlok™ very well

prior to applying the paint.

Materials:• KraftyBlok™ Original (#425100)• Martha Stewart Crafts™ Stencil #32256 – Birds & Berries• Martha Stewart Crafts™ Stencil Adhesive Spray• Martha Stewart Crafts™ Foam Pouncers Set - #32243 • Martha Stewart Crafts™ Multi-Surface Satin Craft Paint Colors: Beetle

Black, Sycamore Bark, Spring Pasture, Jacaranda, Wedding Cake and Geranium

• 5 (12 oz.) bags of Clear Glass Marbles• Rubbing alcohol• Small pointed brush• 6 Long Stem Silk Daisies• 1 Leafy-filler Silk Stem• Paper Towels and Newspaper

Instructions:1. Cover the work area with craft or newspaper.2. Position the KraftyBlok™ so that the hole is at the top.

Plan your design. You may use the design pictured or you may want to create your own pattern.

3. Wipe KraftyBlok™ surface with rubbing alcohol to remove any oily residue.4. Spray back of the birds & berries stencil with stencil adhesive spray.5. Place the stencil on KraftyBlok™ surface.6. Pour a small amount of paint colors on your palette. When loading paint on Pouncers, load it sparingly and dab off excess.7. Lightly dab with Pouncer on a thin layer sycamore bark paint and stencil the branches first. Apply a second coat if necessary.

Remove stencil and let dry.8. Follow the same steps for each stenciled part of the design (letting paint dry in between each step). Stencil leaves with spring pasture paint.

Stencil birds with geranium paint. Stencil flowers with jacaranda paint.9. Paint a small dot in the center of each flower using beetle black paint. Let dry. Paint a smaller dot inside of the beetle black dot using

wedding cake paint.10. Pour the glass marbles into the hole at the top of the KraftyBlok™.11. Insert your silk flower stems into the marbles in the KraftyBlok™ and arrange. Enjoy!

Documents

Rudolph The Red Nosed Luminary 13 - Delphi Glass Krafty Blok eBook-219512.pdf · 18. Place the KraftyBlok™ on its back with the “Owl” image facing up. Apply glue to Section