Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
banner stands
rollup 02RU-S2-S-4 Stylish design and proven reliability makes the Rollup 02 a quality banner stand. Available in both black and silver, the Rollup 02 is one of the most feature-rich single-sided retractable banner stands available.
dimensions:Hardware Graphic
Assembled unit: 33.75”(w) x 62.75 - 85.75”(h) x 7.87”(d) approx.857mm(w) x 1594 - 2178mm(h) x 200mm(d) approx.
Base dimensions:33.75”(w) x 3.5”(h) x 7.87”(d) approx.857mm(w) x 89mm(h) x 200mm(d) approx.
additional information:
Graphic materials:anti-curl vinyl, premium opaque fabric, me-linex
Stand-off rectangle counter top is available in black thermoform only.
Stand-off literature rack is available (L112-2 only)
- Variable graphic height = 60” - 83”- Hybrid bungee/ telescoping pole with
toolless quick rail pole- Accessory channel featured on the top of
the unit (to add a literature pocket or arm table accessory)
features and benefits:
Shipping
Shipping dimensions - ships in one box37”(l) x 10”(h) x 5”(d)940mm(l) x 254mm(h) x 127mm(d)
Approximate shipping weight (w/o graphic):11 lbs/ 4.98 kg
Visible dimensions:Refer to related graphic template for more information.
WARNING: Always attach graphic to base and top rail before removing the locking pin. After fitting, the graphic should be left for 24 hours before use to ensure the adhesive bonds sufficiently. Opening the base will invalidate the product warranty.
Graphic tension may be re-applied or added by removing the end cap, then turn the ratchet tensioner clockwise.
- Anodized silver base- Quick slide graphic to leader attachment- Graphic tensioner- Premium padded carry bag included- Lifetime limited warranty against
manufacturer defects
LV4 banner lighting option available
03.01.16 © Nimlok Display and Exhibit Solutions Worldwide. For questions contact your local Nimlok distributor
Banner Stand Accessories:easy connection with cam lock
and channel
arm table accessory addition
Hybrid pole
Carry bag included
Graphic to top rail attachment (metal insert)
Set-up
1 2 3 4
1 2 3 4
1
Quick slide top rail attachment (plastic insert)
5 2
metal insert
metal insert
metal insert
3
top slider
printed side down
Secure pole(s) in the base of stand then add doublerTwist telescopic pole to extend
Gently lean the unit back and pull the graphic up by the toprail
Peel film to expose adhesive; place metal insert from graphic rail on top back side of the graphic point
Loosen each screw from the rail using provided allen key and remove metal insert (do not remove screws)
Press down on the metal insert to make sure adhesive is secure on graphic
Insert the metal insert with graphic attached into the top graphic profile rail
Tighten the screws back in place to hold metal insert and graphic with an allen key
Leveling feet located under unit
Remove top slider from graphic railRemove film to expose adhesive on top slider
Align and apply to top slider on the top front of graphic
4 1
Quick slide base attachment
2 3
4 5 6
slider printed side up
Align and apply to back of graphicInsert graphic onto graphic railPeel film to expose adhesive tape on quick slider
Insert slider with graphic applied into quick slider, then center
Remove pin while holding onto the graphic so the graphic does not retract in quickly
Slide the quick slider off the leader
Slowly retract the graphic back into the base
top rail slider bottom slider
graphic back
graphic frontgraphic back
graphic front
check out these related products:
We continue to improve and modify our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. See Graphic Templates for graphic bleed specifications.
rollup 01
rollup 06 smart banner 01 smart banner 02
rollup 04 rollup 05rollup 02 rollup 03
rollup DS 01 rollup DS 02