Upload
docong
View
219
Download
1
Embed Size (px)
Citation preview
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.22
RS SERIES
The RS Series motors are the most economical model in the White product line, but are not low-tech. Unlike competitive products using power robbing, two-piece rotor set designs with sliding contact points, RS Series motors utilize the patented Roller Stator® design. Seven precision rollers for the contact points reduce friction, providing more power and longer life for your application. Each output shaft is custom ground to maintain exact tolerances between the housing and shaft, producing high volumetric efficiencies. Industry standard mounting flanges and output shafts allow the RS Series motors to interchange with competitive designs.
Features
High Pressure Viton® Shaft Seal offers superior seal life and performance and eliminates the need for case drain.
Pressure Fed Bearing surface receive positive flow of clean, cool oil.
Roller Stator® Motor Design increases efficiency and life by using roller contact versus solid, sliding contact design.
Match Ground Shaft is matched to housing bore to maintain highest volumetric efficiencies.
Heavy-Duty Drive Link receives full flow lubrication to provide long life.
Code0304
0599
06
081012
14
18
24
Displacementin 3/rev
(cm3/rev)
3.2 (52)4.6 (76)
5.4 (89)6.3 (103)
6.8 (111)
7.7 (127)10.0 (164)12.5 (205)
15.5 (254)
17.9 (293)
24.9 (409)
Max SpeedRPM
� Cont.� Inter.� 400� 490� 460� 540
� 420� 580� 510� 570
� 460� 600
� 410� 530� 370� 460� 300� 370
� 300� 360
� 300� 310
� 190� 220
Max FlowGPM (LPM)
� Cont.� Inter.� 6 (23)� 10 (38)� 10 (38)� 12 (45)
� 10 (38)� 14 (53)� 14 (53)� 16 (61)
� 14 (53)� 18 (68)
� 14 (53)� 18 (68)� 16 (61)� 20 (76)� 16 (61)� 20 (76)
� 20 (76)� 24 (91)
� 20 (76)� 24 (91)
� 20 (76)� 24 (91)
Max Torquelb-in (Nm)
� Cont.� Inter.� *Stall� 730 (82)� 840 (95)� 580 (650)� 1070 (121)� 1230 (138)� 875 (100)
� 1300 (150)� 1480 (167)� 1045 (118)� 1500 (169)� 1725 (194)� 1170 (132)
� 1630 (184)� 1900 (214)� 1320 (149)
� 1600 (180)� 1850 (208)� 1330 (151)� 1970 (222)� 2350 (265)� 1770 (200)� 2640 (297)� 3050 (343)� 2295 (259)
� 2540 (268)� 3040 (342)� 2280 (258)
� 2460 (277)� 3100 (349)� 2110 (238)
� 3350 (377)� 4100 (462)� 3200 (362)
Pressure ∆PSI(∆---Bar)� Cont.� Inter.� Peak� 1750 (121)� 2000 (138)� 2250 (155)� 1750 (121)� 2000 (138)� 2250 (155)
� 1750 (121)� 2000 (138)� 2250 (155)� 1750 (121)� 2000 (138)� 2250 (155)
� 1750 (121)� 2000 (138)� 2250 (155)
� 1500 (103)� 1750 (121)� 2250 (155)� 1500 (103)� 1750 (121)� 2250 (155)� 1500 (103)� 1750 (121)� 2250 (155)
� 1250 (86)� 1500 (103)� 1750 (121)
� 1000 (69)� 1250 (86)� 1500 (103)
� 1000 (69)� 1250 (86)� 1500 (103)
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.23
RSSERIES
050
080
Torque, lb-in (Nm)Speed, RPM?
3.2 in. 3/r (52 cc)
4.6 in. 3/r (76 cc)
090 5.4 in. 3/r (89 cc)
Note: Max Flow and Max Pressure must not occur simultaneously.
Note: Performance data is typical. Performance of production units varies slightly from one motor to another.
Areas within white represent maximum motor efficiencies.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.24
RSSERIES
Note: Performance data is typical. Performance of production units varies slightly from one motor to another.
110
100 6.3 in.3/r (103 cc)
Torque, lb-in Nm)Speed, RPM
Note: Max Flow and Max Pressuremust not occur simultaneously.
6.8 in.3/r (111 cc)
Areas within white represent maximum motor efficiencies.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.25
RSSERIES
Note: Performance data is typical. Performance of production units varies slightly from one motor to another.
160
7.7 in.3/r (127 cc)125
10 in.3/r (164 cc)
Torque, lb-in Nm)Speed, RPM
Note: Max Flow and Max Pressuremust not occur simultaneously.
Areas within white represent maximum motor efficiencies.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.26
RSSERIES
Note: Performance data is typical. Performance of production units varies slightly from one motor to another.
200
250
12.5 in.3/r (205 cc)
15.5 in.3/r (254 cc)Torque, lb-in Nm)Speed, RPM
Note: Max Flow and Max Pressuremust not occur simultaneously.
Areas within white represent maximum motor efficiencies.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.27
RSSERIES
Note: Performance data is typical. Performance of production units varies slightly from one motor to another.
400
300 17.9 in.3/r (293 cc)
24.9 in.3/r (409 cc)Torque, lb-in Nm)Speed, RPM
Note: Max Flow and Max Pressuremust not occur simultaneously.
Areas within white represent maximum motor efficiencies.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.28
RSSERIES
2-Hole Front Offset Manifold Ports 1/2 BSP.F (TP)*
A10
3.249 (82.5)3.242 (82.3)
.12 (3)
1.89 (48)Max.
1.63(41)
A17A67
?? ????
B
A13
1.89 (48)Max.
2.03 (52) for A11, and A19 Housings1.85 (47) for A17 Housing
5.19 (132)Max.
4.187(106.3)
.522 (13.3)
.514 (13.1).05 (1)
Seal Groove Detail
.105 (2.6)
.110 (2.8)
(TP)* These housings have ataller pilot height. Seedimensions below.
A18A68A11
2-Hole Front Ports 1/2 NPT2-Hole Front Aligned Ports 1/2 BSP.F2-Hole Front Aligned Ports 1/2 BSP.F (TP)*2-Hole Front Ports SAE #10
A12A62
2-Hole Front Offset Ports 1.2 BSP.F2-Hole Front Offset Ports 1/2 BSP.F (TP)*
A12 HousingA10,A18,A11Housings
.105 (2.9)
.110 (3.2)
Dim A1.36 (35)
.105 (2.9)
.110 (3.2)
Dim A2.78 (71)
B
.63 (16)
.79 (20)A
.205 (5.2)
.210 (5.3)A62 Housing
A63
Dim A is on page 8.32
B
A
1.82 (46)
.91 (23)
A68 Housingonly
.205 (5.2)
.210 (5.3)
2-Hole Front Manifold Ports2-Hole Front Manifold Ports (TP)*
A17 Housing.105 (2.9).110 (3.2)
1.54 (39)Dim A
.56 (14)
.56 (14)
A
1.25 (32)
A67 Housing .205 (5.2).210 (5.3)
A17A67
(4) 5/16-18 UNC (.50 Deep Min.)(4) M8 x 1.25 (.50 Deep Min.)
(2) 1/2 Dia. Spotface x .073 (19) Deep
2-Hole Front Offset Manifold Ports 1/2 BSP.F
A13 Housing.105 (2.9).110 (3.2)
1.36 (36)
Dim A
1.42 (36).79 (20)
.79 (20)
.63 (16)
.79 (20) A
B
.205 (5.2)
.210 (5.3)A63 Housing
.79 (20)
.79 (20)
(2) 1/2 - 14 BSP.FPorts .55 (14) Deep
(4) M8 x 1.25 .30 (8)Deep Min.
HOUSINGSSAE ‘A’ FLANGE
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.29
RSSERIES
HOUSINGSSAE ‘A’ FLANGE
?? ????
????
B
A70A71A72
2-Hole Side Ports 1/2 NPT2-Hole Side Ports 7/8 O-Ring2-Hole Side Ports 1/2 BSP.F
Dim. A is on page 8.32
Dim A
2.23 (57)
1.63 (41)
.11 (3)
1.22 (31)
.98 (25)
1.76 (45)Max.
1.76 (45)Max.
1.53 (39)Max.
1.53 (39)Max.
1.94 (49)Max. 1.53 (39)
Max.
1.76 (45)Max.
1.53 (39)Max.
3.25 (83)O (4) 3/8-16 UNC-2B Thread.62 (16) Min. Deep
.06 (2)Seal Groove Detail
.12 (3)
2.76 (70)
F30F31
4-Hole Front Ports 1/2 NPT4-Hole Front Ports 7/8 O-Ring
Dim B
B
A
1.69 (43)
.90 (23)
.90 (23)
Dim. B is on page 8.32
F37 4-Hole Front Manifold Ports
Dim B1.70 (43)
0.56 (14)0.56 (14)
A
1.25 (32)
1.25 (32)
.90 (23)
.90 (23)
(2) 1/2 Dia. Port.68 (17) Dia. Spotface x .07 (2) Deep
(4) M8 x 1.25.50 (13) Deep
4-Hole
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.30
RSSERIES
HOUSINGSSAE ‘B’ FLANGE
1.63 (41)
1.80 (46)
.90 (23)
Dim. D
(146.1)5.750
.513 (13.1)
.522 (13.3)
Max.6.96 (176.8)
2.38 (59.5) 2.38 (59.5)2.00 (50.8) .125
3.992 (101.4)3.999 (101.6)
.06 (2).12 (3)
.125 (3)
.98 (25)
1.22 (31)
1.61 (41)2.21 (56)
D
B70B71B72
2-Hole Side Ports 1/2 NPT2-Hole Side Ports 7/8 O-Ring2-Hole Side Ports 1/2 BSP.F
Dim. D is on page 8.32
B18B10B11
2-Hole Aligned Ports 1/2 BSP.F2-Hole Aligned Ports 1/2 NPT2-Hole Aligned Ports 7/8 O-Ring
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.31
RSSERIES
HOUSINGSValve Cavity Housings
A19 2-Hole Front Offset Ports 7/8 O-Ring
1.28(33)
1.58 (40)
3.73 (95)
.63 (16)
.79 (20)
Dim A
1.56 (40)
B
A
1.36 (35)
2.78 (71)
F39 4-Hole Front Offset Ports 7/8 O-Ring
1.31 (33)Optional Relief Cartridge Shown Installed
1.43 (36)
Valve Cavity - 10 Series/2-way (7/8-14 UNF-2B)
Dim B
1.70 (43)
3.26 (83)
.57 (14)
.85 (22)
1.70 (43)
2.97 (75)
A
B
The mounting dimensions are shownon page 8.29.
The mounting dimensions are shownon page 8.28.
Both housings shown on this page areonly available with valve cavities.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.32
RSSERIES
700
600
500
400
300
200
100
RPM0 100 200 300 400 500 600 700 800 900 1000 1100
100 200 300 400 500 ?
500 lbs222 DaN
1000 lbs445 DaN
Disp. Dim. B WeightCode in (mm) lbs (kg)
050 5.36 (136) 13.4 (6,1)080 5.50 (140) 13.9 (6,3)090 5.58 (142) 14.1 (6,4)100 5.72 (145) 14.6 (6,6)110 5.82 (148) 15.1 (6,9)125 5.82 (148) 15.1 (6,9)160 6.04 (153) 15.4 (7,0)200 6.29 (160) 16.0 (7,3)250 6.59 (167) 17.1 (7,8)300 6.83 (173) 17.9 (8,1)400 7.54 (192) 20.2 (9,2)
Disp. Dim. A WeightCode in (mm) lbs (kg)
050 5.29 (134) 16.1 (7,3)080 5.44 (138) 16.5 (7,5)090 5.51 (140) 16.8 (7,6)100 5.65 (144) 17.2 (7,8)110 5.75 (146) 14.4 (6,5)125 5.75 (146) 17.7 (8,0)160 5.97 (152) 18.2 (8,3)200 6.22 (158) 18.8 (8,5)250 6.53 (166) 19.8 (9,0)300 6.76 (172) 20.5 (9,3)400 7.47 (190) 22.7 (10,3)
Disp. Dim. D WeightCode in (mm) lbs (kg)
050 5.29 (134) 18.6 (8,5)080 5.44 (138) 19.0 (8,6)090 5.51 (140) 19.3 (8,8)100 5.65 (144) 19.7 (9,0)110 5.75 (146) 16.9 (7,7)125 5.75 (146) 20.2 (9,2)160 5.97 (152) 20.7 (9,4)200 6.22 (158) 21.3 (9,7)250 6.53 (166) 22.3 (10,1)300 6.76 (172) 23.0 (10,5)400 7.47 (190) 25.2 (11,5)
RS Series Motor
1200 1300
DaN
Thrust Load
Bearing Curve: The bearing curve above represents the side load capacity of the motor at the centreline of the key for various motor speeds.
SAE A Flange
Length and WeightTables
4-Hole Flange
RS motor weights vary +/- 1 lb. (.45 kg) depending upon exact motor configuration.For Speed Sensor motors add .82 (21) to Dim. A
SAE B Flange
RS motor weights vary +/- 1 lb. (.45 kg) depending upon exact motor configuration.For Speed Sensor motors add .67 (17) to Dim. B
RS motor weights vary +/- 1 lb. (.45 kg).
TechnicalAllowable Side LoadOperating conditions within the shaded area will maintain acceptable oil film lubrication with recommended fluids. Operating conditions outside the shaded area are susceptible to motor failure due to oil starvation and/or excessive heat generation. Fluids with low lubricity or low viscosity may require maximum load and speed ratings to be derated to provide acceptable motor life and performance.
lbs
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.33
RSSERIES
SHAFTS
Ø .810
30°1.00-6B Spline (SAE J499 Std.)
5/16”-18 UNC
1.46 (37)
MountingFlange
.63 (16)
.37 (9)
5/16”-18UNC 30°
1.45 (37)
30°5/16”-18 UNC
.70 (18) Min.
.25 (6.4)
1.020 (26.0).970 (24.6)
1.57 (40)
3/4”-28 Slotted Nut 1.125 (29) Across Flats Torque to 150 ft.lbs (203 Nm)
.092(2,3)
.770 (19.6)
.720 (18.3).16 (4)
.67 (17)1.00 (25)
.09 (2) 15°
1:8
Note: A slotted nut is standard on this shaft.
1.86 (47)
30°
1.218 (30.9)1.168 (29.7)
1.70 (43)
M8 x 1.25
.24 (6.1)18 Min.
1216 .21 (5)
1015 .18 (6)
30°13 Tooth 16/32 Pitch Std. ANSI B92.1 - 1996 Spline
5/16”-18 UNC-2B
Dim C
Dim CMountingFlange
Dim C MountingFlange
MountingFlange
Dim C
MountingFlange
Dim C
MountingFlange
Dim C
Max. Torque: 6,000 lb-in680 Nm05 1 Inch Pinhole
.999 (25.4)
.998 (25.3)
Max. Torque: 5,800 lb-in650 Nm10 1 Inch Straight
*15 1 Inch Straight Ext.
.999 (25.4)
.998 (25.3)
.251 (6.4)
.250 (6.4).251 (6.4).250 (6.4)
1.110 (28.2)1.101 (28.0)
Max. Torque: 5,800 lb-in650 Nm13 1 Inch Tapered
Max. Torque: 6,000 lb-in680 Nm01 13 Tooth Spline
Max. Torque: 6,000 lb-in680 Nm02 6-B Spline
Max. Torque: 6,000 lb-in680 Nm12 25mm Straight
1.000 (25.4).999 (25.4)
.189 (4.8)
.188 (4.8).189 (4.8).188 (4.8)
*16 25mm Straight Ext.
.984 (25.0)
.983 (25.0)
.314 (8.0)
.313 (8.0)
1.094 (27.8)1.085 (27.6)
.277 (7.0)
.276 (7.0)
1.00 (25)Min. Spline
.70 (18)Min.
.996 (25.3)
.992 (25.2)
(20.6)
.245 (6.2)
.243 (6.1).71 (18)
.874 (22.2)
.872 (22.1)
ShaftCode
SAE “A” Flange in (mm)
4-Hole Flangein (mm)
SAE “B” Flange in (mm)
05 1.73 (44) 1.66 (42) 1.73 (44)10 1.73 (44) 1.66 (42) 1.73 (44)02 1.73 (44) 1.66 (42) 1.73 (44)12 2.13 (54) 2.08 (53) 2.13 (54)13 2.20 (56) 2.13 (54) 2.20 (56)15 1.56 (40) 1.53 (39) 1.56 (40)16 1.54 (39) 1.55 (39) 1.54 (39)01 1.77 (45) 1.70 (43) 1.77 (45)
Shaft Lengths
Dim C* The #15 and #16 shafts are to be used with speed sensor motors only.
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE Page 8.34
RSSERIES
Code
050
080
090
100
110
125
160
200
250
300
400
Displacements
52 cc3.2 in3/r
76 cc4.6 in3/r
89 cc5.4 in3/r103 cc
6.3 in3/r111 cc
6.8 in3/r
127 cc7.7 in3/r
164 cc10 in3/r
205 cc 12.5 in3/r
254 cc 15.5 in3/r
293 cc17.9 in3/r
409 cc24.9 in3/r
Code
01
02
05
10
12
13
15
16
Shafts
7/8" 13 Tooth
1" 6-B Spline
1" Pinhole
1" Straight
25mm Straight
1" Tapered
1" Straight Ext. (S)
25mm Ext. (S)
Code
OXP
*R1
*R2
**Z
**Z1
**Z2
**Z3
**Z4
**Z5
**Z6
Options
No OptionsSolid NutLock Nut
1000 PSI (69 Bar) Relief Valve Installed2000 PSI (138 Bar) Relief Valve Installed
50 Pulse Sensorw/4pin Connector
50 Pulse Sensor w/Male (tower) Hsg. Weather
Pack Connector30 Pulse Sensorw/4pin Connector
30 Pulse Sensor w/Male (tower) Hsg. Weather
Pack Connector30 Pulse Sensor
w/Female (shroud) Hsg. Weather Pack Connector
100 Pulse Sensorw/4pin Connector 100 Pulse Sensor
w/Male (tower) Hsg. Weather Pack Connector
Code
A10
A11
A12
A13
A17
A18
A19
A62
A63
A67
A68
A70
A71
A72
B10
B11
B18
B70
B71
B72
F30
F31
F37
F39
2-Hole 1/2" NPTAligned Ports (S)
2-Hole 7/8" O-ringAligned Ports (S)
2-Hole 1/2" BSP.F Offset Ports (S)
2-Hole1/2" BSP.F Offset Manifold (S)
2-Hole ManifoldPorts (S)
2-Hole 1/2" BSP.F Aligned (S)
2-Hole 7/8" O-ring With Valve Cavity (S)
2-Hole 1/2" BSP.F Offset w/.200 Pilot
2-Hole 1/2" BSP.F Offset Manifold w/.200
Pilot
2-Hole Manifold Ports w/.200 Pilot
2-Hole 1/2" BSP.F Aligned w/.200 Pilot
2-Hole 1/2" NPT Side Ports
2-Hole 7/8" O-ringSide Ports
2-Hole 1/2" BSP.FSide Ports
2-Hole SAE B Flange1/2" NPT Aligned
2-Hole SAE B Flange7/8" O-ring Aligned
2-Hole SAE B Flange1/2" BSP.F Aligned
2-Hole SAE B Flange1/2" NPT Side Ports
2-Hole SAE B Flange7/8" O-ring Side Ports2-Hole SAE B Flange1/2" BSP.F Side Ports
4-Hole 1/2" NPTAligned Ports (S)
4-Hole 7/8" O-ringAligned Ports (S)4-Hole Manifold
Ports (S)
4-Hole Manifold Ports W/Valve Cavity (S)
* Available with A19 and F39 housings
** Available with A10, A11, A12, A13, A17, A18, A19, F30, F31, F37, and F39 housings and must use the 15 or 16 shaft
(S) Speed sensor components
Housings
DISPLACEMENT
200201
SHAFT OPTIONSHOUSING
SERIES
REVERSED TIMING
200 201
B A B A
RS Rotation SelectionFor applications requiring the motor to rotate in only one direction, shaft seal life may be prolonged by pressurizing the B port of the motor. To obtain the desired direction of shaft rotation, use the graphic at the left to determine the rotation code for the motor. For bidirectional applications, the 200 series is recommended. Preferred rotation is based on rotor timing. Changing preferred direction requires no unique parts.
Ordering Information
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE
RSSERIES
WHITE MOTORS
CROSS HYDRAULICS PTY LTD GREEN CATALOGUE
RSSERIES
LAESTSUDLAESTSUDLAESYDOBGNIRERIWTILPS
GNIRAEBTSURHTMIHSPUKCABLATEMGULPGNILOOCLAESERUSSERPHGIH
ETALPRAEWMIHSPUKCABLATEM.TLPRAEWTNUOMDIMMIHSPUKCABNOLFET
REVOCDNELAESTFAHSEVLAVFEILERISP0001)3(SLAESYDOB
2000 PSI RELIEF VALVE3000 PSI RELIEF VALVE
TUNDETTOLS82-4/3REIRRACLAESTUNKCOL82-4/3REHSAWTSURHT
MANIFOLD SEAL
ROTORS, DRIVE LINKS AND SPACERS, AND BOLTSWHEN CHANGING MOTOR DISPLACEMENTS, A MATCHING DRIVE LINK KIT,DRIVE LINK PIN KIT, AND BOLT SET KIT MUST ALSO BE ORDERED.
HOUSING KITS (EXPLODED VIEW ITEM #20)
F.PSB"2/1/WTNUOMCIRTEMELOH-4-83G#TPN"2/1/WELOH-4-03F#STROPDLOFINAM/W.TNMCIRTEMELOH-2-71G#GNIR-O"8/7/WELOH-4-13F#
TOLIP002.DNAF.PSB41-2/1/WELOH-2-26A#TPN"2/1/WELOH-2-01A#TOLIP002.DNA.DLFNMTESFFO/WELOH-2-36A#GNIR-O"8/7/WELOH-2-11A#
TIVACEVLAV&GNIR-O"8/7TESFFO/WELOH-2-91A#STROPDLOFINAM/WELOH-4-73F# YTIVACEVLAV&GNIR-O"8/7TESFFO/WELOH-4-93F#STROPDLOFINAM/WELOH-2-71A# Y
TOLIP002.DNAF.PSB41-"2/1DENGILA/WELOH-2-86A#F.PSB"2/1TESFFO/WELOH-2-21A#TOLIP002.DNADLOFINAMDENGILA/WELOH-2-76A#F.PSB"2/1/W.DLFNMTESFFO/WELOH-2-31A#
F.PSB"2/1DENGILA/WBEASELOH-2-81B#F.PSB"2/1DENGILA/WELOH-2-A1A#TPN"2/1DENGILA/WBEASELOH-2-01B#GNIR-O"8/7/WELOH-6-15A#
GNIR-O"8/7DENGILA/WBEASELOH-2-11B#TPN"2/1/WELOH-6-05A#STROPEDISTPN"2/1/WBEASELOH-2-07B#STROPEDISTPN"2/1/WELOH-2-07A#
STROPEDISGNIR-O"8/7/WBEASELOH-2-17B#STROPEDISGNIR-O"8/7/WELOH-2-17A#STROPEDISF.PSB"2/1/WBEASELOH-2-87B#STROPEDISF.PSB"2/1/WELOH-2-27A#
#A18- 2-HOLE ALIGNED W/ 1/2" BSP.F
SHAFTS AND RELATED COMPONENTS KITS HOUSING/SHAFT KITS.32&22,12,02SMETIHTIWEMOCSTIKTFAHS/GNISUOH).cte,stun,syek.e.i(STNENOPMOCTFAHSDETALERHTIWEMOCSTIKTFAHS
#05- 1" WITH .373 PINHOLE#53- 1" WITH .406 PINHOLE#10- 1" STRAIGHT#02- 6-B SPLINE#01- 13 TOOTH SPLINE#12- 25MM STRAIGHT (8MM KEY)#13- 1" TAPERED (WITH LOCKNUT)#18- 25MM STRAIGHT (7MM KEY)#03- 6-B EXTENDED NOSE#15- 1" STRAIGHT SPEED SENSOR#16- 25MM STRAIGHT SPEED SENSOR#11- 1" STRAIGHT W/ METRIC THREAD
200229100
200229103---
200229100
---200229101200229102
200229101200229100
EXPLODED VIEW ITEM #DESCRIPTION
TO ORDER A MATCHED HOUSING/SHAFT KIT, PLEASECONTACT A CROSS HYDRAULICS CUSTOMER SERVICEREPRESENTATIVE.
RS (200) SERIES MOTOR COMPONENTSMISCELLANEOUS KITS
DESCRIPTION
9121
910
NOT SHOWNNOT SHOWN
DESCRIPTION
---
200013601
22SHAFT KIT
200011100
23
N/A
NOT SHOWN
200013600200013602
200013201200013101200013501200013700
DRIVE LINK KIT
200047005
300
TIKGNISUOHNOITPIRCSED
BECAUSE THE HOUSING AND SHAFT ARE MATCH GROUND AS A SET TO EXTREMELY TIGHT TOLERANCES AT THE FACTORY, WHITE HYDRAULICS DOES NOTRECOMMEND THAT INDIVIDUAL HOUSINGS OR SHAFTS BE ORDERED TO REPAIR A MOTOR. IT IS RECOMMENDED THAT A MATCHED SET BE ORDERED. TOORDER A MATCHED HOUSING/SHAFT KIT, SEE THE HOUSING/SHAFT KITS LISTING BELOW RIGHT.
400
HOUSING KIT
200247009 200247011 200014003200225018
200160
250
125110100 200997001
200087003200097003
DRIVE LINK PIN KIT15
SEAL KIT
4141STANDARD ROTOR KIT FREETURN ROTOR KIT
NOT SHOWNNOT SHOWN
ITEMS #9 - 10
200067012
200037005
INCLUDED IN
200222003
200067010090080
EXPLODED VIEW ITEM #DISPLACEMENT
050
178 2002220027
NOT SHOWN
13INCLUDED IN
4 21318-1#SMETI5
6
811100222002:TIKLAESNI3
2 ITEMS #1-10 INCLUDED
KIT
1 1
EXPLODED VIEWITEM #
200018012
SEAL KIT 200222001
SEAL KIT
DESCRIPTIONEXP VIEW
ITEM # KIT
200018013200018011200018999200012000200012001200016003500018228500018231500018221200229300200018077200018022
BOLT SET KIT
200147005200187009
200037003200047004
200014002200014002
200224003200224008
200107010200127011
200107009200127009
200224005200224008200224006200224008
200147006
200014001200014001200014001200014001200014003200014003200014003
200087004200097004
200225014
200224010200224012200224014
200225005200225010200225010200225012
200225003200225005200225005200225010
200013403200013702
200014003200225024200224024
200224018200187011
200013401200013301
200013103
200013606200013605
200013612200013203
200013105200013304200013607
KEY KIT
200013202200013204200013108
200013205
200013703
200011101200011103
200013109200013611
200011000 ---
200013610
200011106
---
200011107
200011001
200013604
TO ORDER INDIVIDUAL KEYS, USE THE KEY KIT NUMBER. TO ORDER NUTKITS (FOR #13 SHAFT), SEE MISCELLANEOUS KITS LIST ABOVE.
200013106
200011108
200011600200011700
200011104200011602