Due to continuous improvements, specifications are subject to change without notice.Conversion factor 0.95 g/cc based on polyethylene. Calculated based on polystyrene.*1) Smaller mold than this size may limit the clamp force.

*2) The maximum injection pressure and maximum pack pressure are not melt pressure but injection unit output. The maximum injection pressure and maximum pack pressure are the maximum values that can be set. The maximum injection pressure and maximum pack pressure might be limited depending on the molding condition.

*3) Maximum injection rate and maimum injection speed are theoretical values. Maximum injection rate and maximum injection speed cannot be guaranteed when the injection pressure is maximum.*4) The machine with 28mm diameter screw and without option.

Injection Unit ENGLISH METRICInjection Capacity, Maximum GPPS ounces 0.78 0.95 1.68 1.95 2.54 Grams 22 27 48 55 72Theoretical Displacement in3 1.4 1.7 3.1 3.6 4.7 Cm3 24 29 50 58 76Maximum Injection Pressure (S2000i 55B) Psi. *2) 40,611 37,710 30,458 27,557 21,756 Bar *2) 2,800 2,600 2,100 1,900 1,500Maximum Pack Pressure (S2000i 55B) Psi. *2) 40,611 34,809 27,557 23,206 18,855 Bar *2) 2,800 2,400 1,900 1,600 1,300Maximum Injection Velocity (S2000i 55B) in/sec *3) 12.99 12.99 12.99 12.99 12.99 Cm/Sec *3) 33 33 33 33 33Maximum Injection Rate (S2000i 55B) in3/sec *3) 6.33 7.65 10.69 12.40 16.19 Cm3/Sec *3) 104 125 175 203 265Maximum Injection Pressure (S2000i 55B-g) Psi. *2) 40,611 37,710 30,458 27,557 21,756 Bar *2) 2,800 2,600 2,100 1,900 1,500Maximum Pack Pressure (S2000i 55B-g) Psi. *2) 40,611 34,809 27,557 23,206 18,855 Bar *2) 2,800 2,400 1,900 1,600 1,300Maximum Injection Velocity (S2000i 55B-g) in/sec *3) 7.87 7.87 7.87 7.87 7.87 cm/Sec *3) 20 20 20 20 20Maximum Injection Rate (S2000i 55B-g) in3/sec *3) 3.83 4.64 6.48 7.51 9.81 Cm3/Sec *3) 63 76 106 123 161Screw Stroke in 2.95 2.95 3.74 3.74 3.74 mm 75 75 95 95 95Screw Diameter in 0.79 0.87 1.02 1.10 1.26 mm 20 22 26 28 32Screw L/D Ratio 20:1 20:1 20:1 20:1 20:1 20:1 20:1 20:1 20:1 20:1Screw Speed, Maximum (S2000i 55B) min-1 450 450 450 450 450 min-1 450 450 450 450 450Screw Speed, Maximum (S2000i 55B-g) min-1 300 300 300 300 300 min-1 300 300 300 300 300Nozzle Touch Force ton US 1.65 1.65 1.65 1.65 1.65 Tons 1.5 1.5 1.5 1.5 1.5Number of Pyrometers (Barrel/Nozzle) 3/1 3/1 3/1 3/1 3/1 3/1 3/1 3/1 3/1 3/1Total Heat Capacity Kw 3.5 3.8 6.5 7.2 8.4 Kw 3.5 3.8 6.5 7.2 8.4Clamping Unit ENGLISH Standard Optional METRIC Standard OptionalClamping Force tons US 55 71.5 kN 500 650Mold Opening Stroke in 9.84 mm 250Clamp Speed in/sec 21.85 18.50 mm/sec 555 470 Dry Cycle Time @ 50% Stroke sec 1.12 sec 1.12Maximum Daylight in 23.62 25.59 mm 600 650Minimum / Maximum Mold Thickness in 5.9~13.8 5.9~15.7 mm 150~330 150~400Minimum Mold Size in *1) 8.1 x 7.3 mm *1) 205 x 185Maximum Mold Weight lbs Consult Factory kgs Consult FactoryPlaten Size ( h x v ) in 19.6 x 18.5 mm 500 x 470Distance Between Tie Rods ( h x v) in 14.2 x 12.6 mm 360 x 320Tie Rod Diameter in 1.97 mm 50Eject Stroke Maximum in 2.76 mm 70Ejector Force tons US 2.2 kN 20Mold Locating Ring Inside Diameter in 4.00 mm 101.6General Data ENGLISH METRICLength Overall in 145.0 mm 3,684Width Overall in 42.5 mm 1,080Height Overall in 70.4 mm 1,789Weight lbs *4) 6,173 Kg *4) 2,800Nominal Input Power Source Ph/Volt 3Phase, 220 -10%, 60Hz +/-1Hz Ph/Volt 3 Phase, 200V-10% 50/60Hz+/-1HzBreaker Size Machine only Amp 50 Amp 50Breaker Size with Outlets or Mold Heater Amp 150 Amp 150 Machine kva 25.6 kva 25.6 External outlet kva 35.0 kva 35.0 Maximum Total Capacity kva 60.6 kva 60.6

ROBOSHOT S2000 i 55B / S2000 i 55B-g

Moving Platen

Die Space

Robot Mounting Plate

ROBOSHOT S2000 i 55B / S2000 i 55B-g

Ejector Pin End Tap Extremo Final del Botador Torneira Extracao de Fim de Alfinete 1/2”- 13 unc-2B

Moving Platen Platina Móvil Placa Móvel

Ejector Stroke Desplazamiento del Botador Curso de Extracao 70mm 2.8

Stationary Platen Platina Fija Placa Fixa

(A) Max. Clamp Stroke / Desplazamiento Max. de la Prensa / Curso Máx. de Fechamento 250mm 9.8

(A)

37.2mm 1.5

Min. Mold / Molde Mín. / Molde Mín. 150mm 5.9 Max. Mold / Molde Máx. / Molde Máx. 350mm 13.8 Optional Min. Mold / Molde Mín. Opcional / Molde Mín. Opcional 200mm 7.8 Optional Max. Mold / Molde Máx. Opcional / Molde Máx. Opcional 400mm 15.7

Operator SideLado del OperadorLado de Operador

10-M12 Depth / Profundidad / Profundidade 28mm

110mm4.3

10mm0.4

40mm1.6

20mm0.8

25mm1.0

60mm2.4

115mm4.5

15mm0.6

115mm4.5

15mm0.6

AA 0.531" - 1.94" Depth / Profundidad / Profundidade (46 Holes / Hoyos / Buracos) 0.625"-11 UNC-2B - 1.38" Depth / Profundidad / Profundidade

BB 30mm dia. thru (5 Holes / Hoyos / Buracos)

L

L 8 203.2

Platen Surface/Superficie de la Platina/

Superfície da Placa43mm 1.7

OVERALL LENGTH / LONGITUD TOTAL / COMPRIMENTO TOTAL

1551mm61

Overall HeightAltura totalAltura Total

1084mm42.7

Nozzle CenterCentro de la Boquilla

Centro de Bico

Plan View

Elevation

ROBOSHOT S2000 i 55B / S2000 i 55B-g

Moving Platen Stationary Platen

Clamp End View Injection End View

ROBOSHOT S2000 i 55B / S2000 i 55B-g

OVERALL WIDTH / ANCHO TOTAL / LARGURA TOTAL

Electrical ConnectionConexión EléctricaConexão Elétrica

(D) 360mm

14.2 (Tie Bar Spacing)

(Espacio entre Barras) (Espacejamento de Coluna)

(A)

(B)

(C)

(D)

(C) 320mm

12.6 (Tie Bar Spacing)

(Espacio entre Barras) (Espacejamento de Coluna)

(B) 240mm

9.5 (Robot Base Height)

(Altura de la Base del Robot) (Altura de Base de Robot)

(A) 466.5mm

18.4 (Die Cover Top Height)

(Altura Superior de la Cubierta del Molde) (Morra Cobertura Altura Superior)