SK140-3 SIZE STICK TIP AND LINKAGE.

RECOMMENDED BUCKET CAPACITY - 0.90 CUBIC YARDS HEAPED.

REVISIONS

ZONE REV. DESCRIPTION DATE APPROVED

D

C

B

AA

B

C

D

12345678

8 7 6 5 4 3 2 1

.

4805 SCOOBY LANE NWCARROLL, OHIO 43112740-654-5304

The Cutting Edge of Customer Service

THE INFORMATION CONTAINED IN THISDRAWING IS THE SOLE PROPERTY OFCOMPANY WRENCH LTD. ANY REPRODUCTION IN PART OR AS A WHOLEWITHOUT THE WRITTEN PERMISSION OFCOMPANY WRENCH LTD IS PROHIBITED.

PROPRIETARY AND CONFIDENTIALDECIMAL: 0.015"FRACTIONAL: 1/16"ANGULAR: 1

MATERIAL:

DRAWN

APPROVED

MFG. APPR.

DATENAME

TITLE:

SIZE

BDWG./PART NO.

WEIGHT:

SCALE: NTS

UNLESS OTHERWISE SPECIFIEDDIMENSION TOLERANCES AREAS FOLLOWS:

ET 8/4/2014

SK350LC-9 - 72' LONG REACH RANGE

SHEET 1 OF 1

LIFTING CAPACITIES MACHINE : KOBELCO SK350LC‐9DOC No: 21061119 EQUIPMENT : 72' LONG REACHISS: 3  ‐ 28/10/14

2844* 2844* 50ft2688* 2688* 40ft2665* 2665* 4519* 4519* 30ft2744* 2744* 4706* 4706* 5396* 5396* 20ft2925* 2925* 4957* 4474 5865* 5865* 7292* 7292* 9817* 9817* 15423* 15423* 10ft3232* 2894 5207* 3973 6324* 5624 8095* 8052 11308* 11308* 18541* 18541* 5547* 5547* 0ft3716* 2862 5366* 3571 6664* 4916 8700* 6878 12206* 10068 17137* 16965 9019* 9019* ‐10ft4497* 3048 5298* 3359 6757* 4491 8861* 6221 12357* 9217 19017* 16359 12725* 12725* ‐20ft4947* 3557 6407* 4408 8501* 6063 11687* 9139 17296* 16804 16827* 16827* ‐30ft4973* 4688 7282* 6397 9965* 9675 13470* 13470* 21502* 21502* ‐40ft4437* 4437* 6478* 6478* 8774* 8774* ‐50ft

REACH

RADIUS

39.2ft50.8ft58.5ft63.8ft67.2ft68.9ft69.2ft

10ft

HEIGHT

RATING OVER FRONT RATING OVER‐SIDE OR 360 DEGREES

68.0ft65.3ft60.8ft54.1ft

LIFT CAPACITIES CALCULATED AT ATTACHMENT PIVOT POINT ON STICK (lbs)NO ATTACHMENT ON STICK. ATTACHMENT WEIGHT MUST BE SUBTRACTED.

AT MAX REACH 60ft 50ft 40ft 30ft 20ft

THE FOLLOWING NOTES PERTAIN TO THIS MACHINE EQUIPPED WITH 7,920# ADDITIONAL COUNTERWEIGHT.

1. DO NOT ATTEMPT TO LIFT OR HOLD ANY LOAD THAT EXCEEDS THESE RATED VALUES.2. THE OPERATOR SHOULD BE FULLY ACQUAINTED WITH MACHINE OPERATION BEFORE OPERATING THE MACHINE.3. LIFTING CAPACITIES ASSUME MACHINE STANDING ON LEVEL, FIRM AND UNIFORM SUPPORTING SURFACE. OPERATOR MUST MAKE ALLOWANCE FOR JOB CONDITIONS SUCH AS SOFT UNEVEN GROUND, OUT OF LEVEL CONDITIONS, SIDE LOADS, SUDDEN STOPPING OF LOADS, HAZARDOUS CONDITIONS, INEXPERIENCED PERSONNEL, ECT.4. THE ABOVE THEORETICAL RATINGS ARE BASED ON CALCULATIONS DERIVED FROM STANDARD O.E.M LIFT CHARTS BASED ON SAE STANDARD No J1097. THEY DO NOT EXCEED 87% HYDRAULIC LIFTING CAPACITY OR 75% OF TIPPING CAPACITY. RATED LOADS MARKED WITH A (*) ARE LIMITED HYDRAULICALLY.

PAGE 2 OF 2