Request for Bid

For

GE ENDURIS HIGH SOLIDS ROOF COATING SYSTEM The Donley Center

718 Hamilton Street Allentown, PA 18102

Prevailing Wage Serial Number: 18-04899

Advertised: July 6, 2018 Pre-bid Mandatory Meeting: July 18, 2018 10:30 AM @site with the Director of

Facilities & Maintenance-Carl Peckitt Bid Due Date: July 30, 2018

Installation & Certification must be completed by October 15, 2018

4525 EDUCATION PARK DRIVE SCHNECKSVILLE, PA 18078

610-799-2121

1

Table of Contents

Page

Cover Page 1

Table of Contents 2

Introduction 3

General Instructions for Bid 3

Project Scope 4-6

Vendor Bid Form 7

Lehigh Carbon Community College Bid Instructions 8-11

Noncollusion Affadavit 12

Attachment A-Ariel View of Roof 13

Attachment B-GE Enduris Roof Coating Brochure 14-17

Attachment C-Roof Details & Elevations, Installation Details 18-39

Attachment D-Momentive Specification 40-45

2

Introduction

Lehigh Carbon Community College is soliciting bids for GE Enduris 3500 High Solids Silicone Roof Coating System at the Donley Center located in Allentown.

Vendors are required to submit written bids that present the vendor’s qualifications and understanding of work to be performed. The vendor’s bid should be prepared simply and economically and should provide all information it considers pertinent to its qualifications for the specifications listed herein. Emphasis should be placed on completeness of services offered and clarity of content.

A pre-bid mandatory meeting will be held at the site on July 18, 2018 at 10:30 AM. All vendors interested in submitting a bid must attend the mandatory meeting.

Questions regarding the project should be emailed to slindenmuth@lccc.edu until July 20, 2018.

The bid shall be enclosed in a sealed envelope identified as follows: “Sealed bid for GE Enduris Roof Coating-Donley.”

The bid must be submitted no later than 2:00PM on July 30, 2018, directly to the Purchasing & Contract Manager at the following address:

Attn: Susan Lindenmuth, Purchasing & Contract Manager Lehigh Carbon Community College 4525 Education Park Dr. Schnecksville, PA 18078

General Instructions for Bid

A. Bid Content-A completed bid must contain the following:

• Bid Form & Signature Page of Bidding Instructions-the bid form and signaturepage must be completed and signed by an individual authorized to bind thevendor. All bids submitted without the bid form and signature page may bedeemed inadequate.

• Bid Bond• Certificate of Insurance-All vendors must be fully insured per bidding

instructions.• Noncollusion Affidavit

B. Bid Award-It is to be understood by the bidder that the Board of Trustees of theLehigh Carbon Community College may make its award for one or for more than oneof the articles set forth in these specifications. The Board will accept the bid of thelowest responsible bidder when the kinds and quality of supplies and equipment offeredare the same or are equal, but they reserve the right to reject any and all bids or select asingle item from any bid.

C. Basis of Payment-Payment will be made to the vendor within 30 days upon receivingthe invoice.

3

PROJECT SCOPE

SCOPE OF WORK

Applying GE Enduris 3500 High Solids Silicone Roof Coating over existing rubber roof using GE specifications by a licensed and certified contractor of the product.

WORK DESCRIPTION

This work shall include all labor, demolition, material equipment, and qualified services to completely furnish, deliver and erect all work specified hereinafter.

• Supply owner with thermal imaging scan of the existing roof. Anomalies will be markedin paint on the roof and the owner will receive a report of the findings.

• Remove and infill bad areas of existing non-asbestos roofing system.• Clean and prepare existing roof surface in accordance with manufacturers

recommendations and requirements.• Supply and install primer as recommended by the manufacturer to the remaining roof

surface.• Prepare existing seams at all necessary locations per the manufacturer’s specifications.• Supply and install GE SCM 3500 Series construction coating over the entire existing roof

system.• All walls and curbs shall have double thickness of silicone as per manufacturer’s

specifications and recommendations.• Follow the manufacturer’s installation guide included in this spec.• Seal off all air intakes to prevent fumes from entering the building. The building will be

occupied during the course of the project.• Provide a method of installation and protection of existing communication equipment on

roof.• Provide owner with a method of installation for both roof levels and areas to be protected.

FIELD MEASUREMENTS

All accurate field measurements will be the responsibility of the bidder.

FAMILIARITY WITH PROPOSED WORK

The Contract will be entered into by the Owner with the understanding that the contractor, prior to submission of the bid, acquainted himself/herself with the requirements of the drawings and specifications, conditions of the site, all utilities in existence to which connections are to be made and all other requirements of the Contract, and that he obtained all information necessary for the completion of the work on or before the date specified. The Contractor shall not at any time after execution of the Contract set up any claims whatever based upon insufficient data or incorrectly assuming conditions, nor shall the Contractor claim any misunderstanding in regard to the nature, conditions or character of the work to be performed under the Contract, and the Contractor shall assume all risks resulting from any changes to the conditions which may occur during the progress of the work.

4

DELIVERY/PACKAGING

• All materials shall be delivered in suitable packages, boxes or crates and beproperly marked and designated. Bidder is responsible for all damages andpackaging prior to delivery on work site.

• All fixtures and accessories will be shipped together.• Owner will provide suitable storage for materials.

ACCEPTABLE MATERIALS/PRODUCTS

GE Enduris 3500 High Solids Silicone Roof Coating

SAMPLES

Supply owner with a cured sample of product on a small piece of rubber membrane.

INSTALLATION

All workmanship will be in compliance with International Building Codes and of a high quality standard.

CLEAN-UP AND PROTECTION

Upon completion and at bidder’s expenses, all work shall be cleaned as required by the manufacturer and a representative of the College. Protect installation and surrounding area against damages until completion of the project. Work area will be cordoned off at all times during construction and no pedestrian traffic allowed in proximity of job site.

FIELD TEST AND REPORTS A field test with written reports will be supplied prior to final payment. A college representative will inspect each unit when notified of completion.

.DAMAGES/REPAIR

Bidder will be responsible for all damages incurred by them and will make proper repairs upon approval of said repairs by a college representative.

WARRANTIES

Bidder will supply in writing to owner a GE 10 year manufacturer’s warranty.

STANDARD OF QUALITY

The bidder’s proposal must be based on the exact equipment, manufacturer, fabricator, processes, etc., specifically named or described in the specifications without substitutions, unless the names are suffixed with the phrase “or approved equal” in which case the bidder may quote on other equipment, manufacturers, fabricators, processes, etc. of equivalent quality, workmanship and performance, subject however to the approval of a representative of the college who will be the sole judge of the substituted product or service and whose decision will be final.

5

PROJECT COMPLETION AND ACCEPTANCE

The project shall be completed in its entirety no longer than 6 weather permitting working days from its commencement date. Final project acceptance will be made at the sole discretion of a college representative. A 10% project cost retainage will be held by the College until such acceptance.

NOTICE TO BIDDERS

A. The bid you specify will provide a high quality of product type andqualified service upon review of a college representative.

B. Installation of bidder’s product will be verified with a college representative.C. A performance bond will be issued by the awarded bidder.D. The bidder will be responsible to Act 442 – Prevailing Wage Act.E. Reviewed Project Scope yes _____ no_____ initials ______F. Fees and local permits are responsibility of the bidder.G. Invoices will need to be submitted on a AIA Document G702.

6

Vendor Bid Form

TO: LEHIGH CARBON COMMUNITY COLLEGE

We, the Undersigned, having examined the specifications and all other documents and, being familiar with the various conditions under which these services and/or supplies are to be used, agree to furnish, install, and warrant all labor, materials, equipment, and any other required services to fulfill the requirements of the Request for Proposal.

COMPANY NAME:

ADDRESS:

AUTHORIZED SIGNATURE:

PRINTED NAME:

TITLE:

FEDERAL I.D.#:

Bid Amount for project: $__________________________________________________

Verify receipt of: Addendum No. ____ Date Received___________ Addendum No. ____ Date Received___________ Addendum No. ____ Date Received___________

Checklist: Vendor Bid Form Signed Bidding Instructions Bid Bond Non collusion Affidavit

7

LEHIGH CARBON COMMUNITY COLLEGE 4525 EDUCATION PARK DRIVE

SCHNECKSVILLE, PENNSYLVANIA 18078-2598 GENERAL BIDDING INSTRUCTIONS

All bids must be signed and submitted in a sealed, opaque envelope plainly marked on the outside “GE Enduris Roof Coating-Donley” to Ms. Susan Lindenmuth, Purchasing & Contracts Manager, Lehigh Carbon Community College, 4525 Education Park Drive, Schnecksville, Pennsylvania, on or before July 30, 2018 at 2PM Eastern Time.

BIDS ARE TO BE SUBMITTED IN ACCORDANCE WITH THE FOLLOWING GENERAL BIDDING SPECIFICATIONS:

1. Bids will not be considered unless properly made and signed by the bidder.

2. Bids should be either typewritten or written in ink. Bids submitted in pencil may be rejected.

3. Changes, alterations, or interlineations in the bid by the bidder may, at the discretion of the Board of Trusteesof the Lehigh Carbon Community College, void this bid entirely or that part which has been changed, altered,or interlined.

4. (a) Bids must show unit price and total price for each item specified (if applicable). The total pricebid must be stated on the “Calculation Bid Form” which is provided with the bid pack. Where the figures are irreconcilable, awards will be made on the basis of unit prices.

(b) It is to be understood by the bidder that the Board of Trustees of the Lehigh Carbon CommunityCollege may make its award for one or for more than one of the articles set forth in thesespecifications. The Board will accept the bid of the lowest responsible bidder when the kinds andquality of supplies and equipment offered are the same or are equal, but they reserve the right to rejectany and all bids or select a single item from any bid.

(c) The quantities specified are only indicative of the probable amount to be required by the LehighCarbon Community College for the current fiscal year and the Board of Trustees hereby grants to thesuccessful bidder who is awarded a contract under this schedule, the privilege of furnishing additionalitems needed throughout the same fiscal year for which bidder was awarded contract at the same orcurrent market price whichever is lower.

5. (a) All bids for construction, reconstruction, repair, demolition, and/or alteration shall beaccompanied by a bond with corporate surety or certified check in the amount of ten (10) percent of the amount of the bid, as set by the Board of Trustees.

(b) The bidder to whom the construction, reconstruction, repair, demolition, and/or alterationcontract is awarded shall furnish bonds to guarantee the performance of the contract and payment oflabor and materials. Such bonds shall be in compliance with Public Works Contractors' Bond Law of1967 (3 P.S. 191-202). Failure to furnish such bonds shall automatically void the contract award.

(c) All bids for construction, reconstruction, repair, demolition, and/or alteration shall be bid atPennsylvania Prevailing Wages. Pennsylvania Prevailing Wage Act of 1961, P.L. 987, No 442.

(d) All bids for construction, reconstruction, repair, demolition, and/or alteration where theestimated cost of the total project is in excess of $25,000, shall be required to provide a verificationform (EVP) to the College acknowledging compliance with the Public Works EmploymentVerification Act signed into law on July 5, 2012. The verification form (EVP) is provided by the

8

Secretary of General Services of the Commonwealth, acknowledging their responsibilities under and compliance with the Act.

6. INSURANCE REQUIREMENTS for construction, reconstruction, repair, demolition, and/oralteration.

Effective as of the date Contractor is to commence Services to be performed under the contract and continuing until all authorized Services have been fully and completely performed by Contractor, Contractor shall provide and maintain in full force and affect the following minimum insurance coverage as evidenced by Insurance certificates, which shall be furnished to Lehigh Carbon Community College in advance of beginning the Services. Such insurance coverage shall be placed with or carried by insurance carrier or carriers with an A.M. Best Rating of “A” or better, and Lehigh Carbon Community College may elect to require certified copies of the policies in lieu of, or in addition to, certificates of insurance.

a) Pennsylvania Statutory Workers Compensation and Occupational Disease Insurancea. Also Employers Liability Insurance in the minimum amount of $500,000 EachAccident /$500,000 Disease – Each Employee / $500,000 Disease – Policy Limit.

b) Business Automobile Liability Insurance including all owned, hired and non-ownedautomobiles used by or on behalf of Contractor. Minimum $1,000,000 combined single limit foreach occurrence, including bodily injury and property damage.c) Commercial General Liability Insurance against claims for bodily injury, death of and/orproperty damage to third parties with a minimum of $3,000,000 each occurrence. At a minimum,such insurance shall provide coverage for premises-operations, products-completed operations,and contractual liability.d) Excess/Umbrella Liability coverage may be used in conjunction with primary coverage to attainrequired limits of this contract.

Contractor shall assume the risk of loss or damage to all property or equipment furnished by Contractor. Contractor waives Contractor’s right of recovery against Lehigh Carbon Community College and agrees that all insurance policies covering such property or equipment shall be endorsed to affect such waiver.

Contractor’s commercial general liability insurance policy shall be primary and non-contributory to Lehigh Carbon Community College’s insurance. Lehigh Carbon Community College shall be named as an Additional Insured under Contractor’s commercial general liability insurance policy.

Contractor shall waive any rights of subrogation it may have, either at law or in equity, related to or resulting from Lehigh Carbon Community College and hereby agrees as part of the award of the contract, to obtain the same waiver of any rights of subrogation, either at law or in equity, related to or resulting from Lehigh Carbon Community College, from each insurance company issuing Contractor an insurance policy pursuant to the terms hereof.

For all applicable purposes herein, Contractor shall also mean and include Sub-Contractor(s).

7. The bidder agrees, if awarded the contract, to furnish and deliver the said articles at such times, at suchplaces, and in such quantities as directed by the designated representative of the Lehigh CarbonCommunity College and shall be subject to the inspection and approval of the said designatedrepresentative. The awarding of bids by the Board of Trustees of Lehigh Carbon Community College shallauthorize the Vice President for Finance & Administrative Services to execute necessary contracts; butsuch awards are, nonetheless, qualified by the needs of the College and shall not become final as to anyitem or amount until purchase orders are issued by the College, the College reserving the right to decide onitems and amounts needed after the bid is awarded. In the event any of said articles shall be rejected asunsuitable or not in conformity with these specifications such articles shall at once be removed and otherarticles of proper quality as set forth in these specifications shall be furnished in place thereof at theexpense of the successful bidder.

8. As part of the award of the contract, in the event that the successful bidder shall neglect or refuse tofurnish and deliver the said articles or any part thereof as provided in these specifications or to replaceany which are rejected as stated in the preceding paragraph, the bidder authorizes and empowers the

9

Board of Trustees of the Lehigh Carbon Community College to purchase articles in conformity with the contract from such party or parties in such quantities and in such manner as it shall select at the expense of the successful bidder, or to cancel the contract, reserving to itself nevertheless all rights for damages which may be incurred by the Board.

9. The bidder agrees that if awarded the contract, bidder will not assign, transfer, or sublet it.

10. The bidder agrees that if awarded the contract, bidder will not assign or transfer in whole or in part any rightsor privileges which may accrue to bidder under the terms of the contract or any money which may becomedue to bidder there under.

11. Inasmuch as the Community College is not subject to Federal or State taxes, the bid shall not include thesetaxes. A Commonwealth of Pennsylvania, Department of Revenue, Bureau of Sales and Use Tax, "BlanketExemption Certificate" will be furnished by the College upon request of the bidder.

12. Where the invitation for bids describes or specifies a particular article, alternate bids covering articles equalin all respects are permitted, unless otherwise stated. Where an invitation specifies an article by name andthe bidder intends to furnish another article which bidder considers equal thereto, in every such instance thename and grade of the equivalent must be specified in the bid, otherwise no substitution will be allowed.

13. If requested by the College, samples must be furnished to the College for evaluation when an alternate item isbid. All samples must be supplied and returned at the bidder's expense.

14. The bidder does hereby agree that, if awarded the contract under these specifications, bidder will indemnifyand save harmless the Lehigh Carbon Community College, it’s officers, members of the Board of Trustees,and their respective assistants from all suits and actions of every nature and description brought against themor any of them growing out of any contract or contracts, written or verbal, entered into between the LehighCarbon Community College and the successful bidder, and further that upon the awarding of the contract tothe undersigned bidder in accordance with these specifications this agreement of indemnification shallautomatically become effective.

15. Vendors submitting bids for construction, reconstruction, repair, demolition, and/or alteration may berequired to read and sign a Contractor's Waiver of Liens if awarded the contract. However, failure to readand sign Contractor's Waiver of Liens, if required, will void the contract award."

16. The Board of Trustees of the Lehigh Carbon Community College reserves the right to accept or reject any orall bids and to award the bid in the best interest of the Lehigh Carbon Community College as judged by theBoard of Trustees.

17. The singular as used herein shall include the plural, the masculine shall include the feminine and neuter;"articles" as used herein shall include supplies, materials and equipment, and all incidental work and labor ifthe same is contemplated in these specifications.

18. Security PoliciesAlcoholic Beverage and Narcotics PolicyAlcoholic beverages are prohibited on campus at all times regardless of your age. If you are caught withalcohol on campus, it will be confiscated, and you will be asked to leave the campus. Students caught withalcohol on campus will have their I.D. taken. They will then pick up their I.D. at the Student Services Office.The Dean of Students will issue the necessary sanctions which may include fines, community service work,suspension or expulsion from all college activities, along with the possibility of criminal charges.

All illegal narcotics are prohibited on campus and at all college-sponsored events. Anyone caught possessing,transporting, or selling a controlled substance is in violation of both college and state laws. College sanctionsinclude fines, community service work, and expulsion from all college activities, along with the possibility ofcriminal charges. The Pennsylvania State Police may also be summoned. As a result, criminal charges arepossible.

10

Firearms/Weapons Policy Firearms, or any type of weapons, are prohibited on college property. This includes the main campus as well as our satellite sites. Any violators to this policy will be turned over to the Dean of Students and the Pennsylvania State Police. As a result, criminal charges are possible.

The general bidding instructions consist of four (4) pages as noted in lower right page footer. The undersigned bidder certifies to have read every page and offers to furnish the articles specified and to perform all incidental work contemplated herein, to the Lehigh Carbon Community College in exact accordance with these specifications and at the prices stated.

Name of Vendor___________________________________________________________________________

Authorized Signature__________________________________________________Date:_________________

Address__________________________________________________________________________________

Email____________________________________________________________________________________

Phone____________________________________________________________________________________

Fax______________________________________________________________________________________

11

NONCOLLUSION AFFIDAVIT

State of : County of : s.s.

I state that I am the (Title) of (Name of Firm) and that I am authorized to make this

affidavit on behalf of my firm, and its owners, directors, and officers. I am the person responsible in my firm for the prices(s) and the amount of this proposal.

I state that:

1. The price(s) and amount of this proposal have been arrived at independently and without consultation,communication or agreement with any other contractor, proposer or potential proposer.

2. Neither the price(s) nor the amount of this proposal, and neither the approximate price(s) norapproximate amount of this proposal, have been disclosed to any other firm or person who is aproposer or potential proposer, and they will not be disclosed before the proposal submission date.

3. No attempt has been made or will be made to induce any firm or person to refrain from proposing on thiscontract, or to submit a proposal higher than this proposal, or to submit any intentionally high ornoncompetitive proposal or other form of complementary proposal.

4. The proposal of my firm is made in good faith and not pursuant to any agreement or discussion with, orinducement from, any firm or person to submit a complementary or other noncompetitive proposal.

5. (Name of Firm) its affiliates, subsidiaries, officers, directors, and employees are not currently under investigation by any governmental agency and have not in the last four years been convicted or found liable for any act prohibited by state or federal law in any jurisdiction, involving conspiracy or collusion with respect to proposing and/or bidding on any public contract, except as follows:

I state that (Name of Firm) understands and acknowledges that the above representations are material and important, and will be relied upon by the Department of General Services in awarding the contract(s) for which this proposal is submitted. I understand and my firm understands that any misstatement in this affidavit is and shall be treated as fraudulent concealment from the Department of General Services of the true facts relating to the submission of this proposal.

SWORN TO AND SUBSCRIBED (Signature) BEFORE ME THIS DAY OF

, 20 .

(Signatory’s Printed Name) Notary Public

(Signatory’s Title) My Commission Expires

12

Attachment A-Ariel View of Roof outlined in Red

13

GE Enduris*

Silicone Roof Coating

14

Attachment B

2 |

Silicone remains stable, flexible and virtually unaffected by daily and seasonal temperature extremes. It will not become brittle or harden as the system ages. The GE Enduris system provides exceptional, long-term performance.

• Ponding waterWhile acrylic coatings tend to fail at the seams,penetrations and edges, especially where waterponds, Enduris coatings stand up to ponding water.

• Life cycle costPrimerless, single-coat application brings efficiencyand cost savings to the installation process. Long-term durability promotes a lower total life cycle cost.

• Energy savingsEnergy savings versus a black roof can be as great as35% on summer cooling costs. GE Enduris coatingsoffer excellent color retention and reflectivity with asilicone polymer that is UV stable.

• Full compatibilityUsing only 100% silicone components that arechemically and adhesively compatible, Enduris helpsprevent water leakage, mold/mildew, wood rot andmetal rust.

• Best-in-class elongationBy remaining flexible with daily and seasonaltemperatures throughout the life of the building,this system offers best-in-class elongation, bothinitially and after decades of exposure.

Roofs have it hard. On an 89° day, a typical black roof can experience a 100° variation from 175° at the hottest peak to 75° ambient temperature at night. This constant temperature fluctuation and UV exposure can create tremendous strain over time. Most commonly, roofs fail where dissimilar materials meet at penetrations, seams and edges. Minor structural issues can cause additional challenges such as poor drainage and ponding water.

For over 50 years, professionals have trusted GE to deliver durable, long-lasting building solutions. The GE Enduris* roof coating system is a fast, efficient and economical alternative to replacement. Based on GE-heritage technology, the GE Enduris system is backed by world-class technical support and a 10-, 15- or 20-year warranty.

Restore with SiliconeA seamless, stable and energy-efficient coating can dramatically extend roof life expectancy, delaying the need for a costly, time-consuming replacement project.

Silicone is inherently durable and permanently flexible. Unlike acrylic, polyolefin, asphaltic and carbon-based polymer chains, silicone is completely UV stable, providing the maximum long-term performance against weather and atmospheric conditions. The entire GE roof coating system is made from the same 100% silicone, allowing it to expand and contract at the same rate, helping prevent leaks that may result in mold, mildew, wood rot and rust. A white silicone coating also reflects the sun’s rays to better control inside temperatures.

Add Decades to Roof Life in Days Restore with Confidence

R E S T O R E V I R T U A L LY A N Y E X I S T I N G R O O F T Y P E

GE Enduris restoration systems are appropriate over most structurally sound existing roofing systems including:

• Single-ply membranes(TPO, EPDM, PVC)

• Asphaltic and mod bit

Contact us for application to additional substrates

GE Enduris Silicone Roof Coating *Enduris is a trademark of Momentive Performance Materials Inc.

• Metal

• Concrete

• Foam

15

*Enduris is a trademark of Momentive Performance Materials Inc. | 3

GE Enduris* Three-Component System

GE Enduris Silicone Roof Coating

GE Enduris Seam SealantLow-VOC 100% silicone, single-component liquid sealant for joints, seams, gaps and splices, offering long-term performance in sealing out water and withstanding weather and atmospheric conditions without degradation. Currently available in 2-gallon pails.

GE RF100 Reinforcing Fabric This flexible, easy-to-use reinforcing fabric embedded between layers of sealant or coating is acceptable for sealing virtually all seams, curbs and penetrations. Currently available in 4", 6" and 12" widths in 100' rolls. Larger sizes may be available.

• Metal

• Concrete

• Foam

GE Enduris Roof CoatingHigh-solids, low-VOC, 100% silicone liquid coating applied in a single coat. While a primer is not required, an asphalt bleed-blocking base coat can promote energy savings, and an EPDM wash can help optimize adhesion. Currently available in totes, drums and pails and in standard colors white, tan, medium gray and dark gray. Custom colors may be requested.

16

† Inspection of the completed project by a third-party engineering firm is required for warranty validation. See individual product labels for additional information, including specific warranty terms, product application conditions and/or other use requirements or specifications with respect to our claims.

Copyright 2015 Momentive Performance Materials Inc. GE is a trademark of General Electric Company and is used under license by Momentive Performance Materials Inc.

BRO-ROOF-EN(10/15) 12/2015 Printed in USA

In addition to a proven roofing system from a trusted leader, the coatings team offers technical assistance from a project’s inception to completion. With decades of experience on some of the world’s most innovative structures, the team provides a wealth of knowledge and support to help deliver results including:

1. Project Review – Review of project details to assistwith product selection and application based onusage criteria, specifications and customer needs.

2. Drawing Details – Assist in developing drawingdetails that address project-specific terminations,transitions and penetrations.

3. Project Testing – On-site testing for substrateadhesion or compatibility with other buildingmaterials if necessary.

4. Project Warranty† – Extended warranties areoffered for long-term assurance.

Time and labor savings With no primer required on coated and uncoated roofing membranes, this system can offer significant cost savings associated with labor, primer and time delays.

Full compatibility Can be applied to most existing roof types including asphaltics (BUR and Mod Bit), single-ply (TPO, PVC, EPDM), SPF foam, concrete and metal.

Cold weather application GE Enduris* 3500 coating can be rolled or sprayed in temperatures as low as 0° F without freezing, helping to extend the roofing season and avoid project delays.

Made in the USA

To order, call Momentive Customer Service toll-free at 866-275-4372.Fax orders to Customer Service at 614-986-2489.For additional information visit www.ge.com/silicones.

Benefit Now and Later We Stay on Top of It All

SIMPLICIT Y AND INTEGRIT Y FROM A TRUS TED BR ANDWith over five decades of superior product performance, the GE Enduris 100% silicone roof coating system can bring confidence and compliance to roof restorations and repairs. Simplified installation promotes safety and improves efficiency, helping to ensure that the job is done right every time. To learn more about GE-branded coatings, visit www.ge.com/silicones or contact your local distributor today.

*Momentive and the Momentive logo are trademarks of Momentive Performance Materials Inc.

Title 24 Compliant

RATEDPRODUCT

17

18

Attachment C

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

GE Enduris* 3500High Solids Silicone Roof CoatingINSTALLATION GUIDE SPECIFICATION FOR GRANULATED OR SMOOTH MODIFIED BITUMEN / BUR (15 YEAR WARRANTY)

PART 1–GENERAL

1.01 SUMMARY A. This specification provides a remedial coating system for

application over smooth and mineral surfaced modified bitumenroof covers and smooth built-up roof membranes(BUR). The use is restricted to circumstances where the roofsurface is in sound condition, but requires a renewal of themembrane surface due to the normal effect of aging and use.

B. Enduris 3500 silicone roof coating, manufactured by MomentivePerformance Materials, Inc. (MPM), is a high solids, solvent-free,alkoxy-based silicone roof coating which moisture cures to adurable, breathable, waterproof barrier which is highly resistant todegradation from UV and natural weathering. Enduris 3500silicone roof coating may be used to top coat existing granulatedor smooth modified bitumen roofs, for restoration and longevity.

C. Scope: Installation of Enduris 3500 silicone roof coating, labor andaccessory materials.

D. Exclusions: This guide specification does not include: repair orreplacement of roof accessory items such as vents, expansionjoints, drains, penetrations and mechanical equipment;evaluation and correction of roof load capacity or wind upliftresistance.

1.02 SUBMITTALS

A. Product Data: Technical Data Sheets (TDS) and SafetyData Sheets (SDS) for all products used on project.

B. Shop Drawings: Drawings indicating scope of work androofing details.

C. Sample Warranty (optional; see Section 1.06).

1.03 QUALITY ASSURANCE

A. Manufacturer Qualifications: Enduris 3500 high solids, siliconeroof coating supplied and manufactured by MPM areapproved for and shall be used on this project. Upon request,MPM will provide certification that all MPM materials meet thephysical properties required by the specification.

GE is a registered trademark of General Electric Company and is used under license by Momentive Performance Materials Inc. *Enduris is a trademark of Momentive Performance Materials Inc.

40

Attachment D

B. Adhesion Test: Prior to estimating coating restoration project,conduct an adhesion test in accordance with MPM adhesiontesting procedures to determine if a primer or other specificsurface preparation is required.

C. The silicone coating manufacturer shall have a minimum of 20years’ experience in the manufacture of silicone roof coatingsand be ISO 9001 certified. The coating shall have an UnderwritersLaboratories (UL) Listing, Factory Mutual (FM) Class 1, 4470Approval and a Miami-Dade NOA (Notice of Acceptance).

D. Contractor Qualifications: The contractor shall be approved byMPM and eligible to offer a GE Enduris Silicone Labor & MaterialWarranty.

E. Deviations: Any deviation from this specification must beapproved in writing by MPM.

F. Field Quality Control: Upon completion of the roof coatingproject, an inspection by MPM’s designated third-partyinspection agency may be required. Consult with MPM forspecific requirements.

1.04 DELIVERY, STORAGE AND PROTECTION OF MATERIALSA. Delivery: All products shall be delivered in the original, factory-

sealed drums, pails or other containers. All product containersshall be labeled with the manufacturer’s name and address,product name and description, product date/expiration dateand batch/lot number.

B. Materials damaged during shipment, delivery or storage shall notbe used on this project without approval of MPM.

C. Handling and Storage: Store Enduris 3500 silicone roof coatingcontainers between 15°F and 109°F (-9°C to 43°C). Othermaterials shall be stored in accordance with the appropriatematerial’s TDS. Keep all products out of direct sunlight andprotected from extreme temperatures.

D. SDSs and TDSs for all materials used on this project will be kept onsite and reviewed by appropriate personnel before use.

1.05 GENERAL SITE CONDITIONS

A. All mechanical units, skylights, vents and other protrusionsand other rooftop accessories should be in place prior tosurface preparation and coating application.

B. All mechanical units should be adjusted or shut down toprevent fumes and odors from entering the facility.

C. Mask or otherwise protect all surfaces not to be preparedand/or coated to prevent overspray damage. Use windscreens as appropriate.

D. Review existing and imminent weather conditions(including potential for extreme temperatures, relativehumidity, frost, dew, and precipitation) to assure thatcoating and accessory material will have sufficient curingtime.

Warranty Program for GE Enduris Silicone Coatings

GE Enduris High Solids Silicone

Roof Coating

*Enduris is a trademark of Momentive Performance Materials Inc.

41

D.

E. Temperature at the time of application of the Enduris 3500silicone roof coating application should be above 0°F (-18°C) toallow coating to cure properly. Contact manufacturer if applyingto substrates over 120°F (49°C).

F. Apply Enduris 3500 roof coatings only to clean, dry and securesurfaces.

G. Protect Enduris 3500 roof coating from foot traffic or otherpotential abuse during the curing process. The coating isconsidered cured when it is tack free and sufficiently durable towithstand roof traffic.

H. All work performed under this specification must be inaccordance with all appropriate local, state and federalregulations.

I. While cured Enduris 3500 roof coating is unaffected by pondingwater conditions, various professional roofing associations(including NRCA) consider ponding water undesirable andrecommend that roofs be designed for positive drainage.Corrective action should be considered, prior to application ofEnduris 3500 roof coating, to correct existing ponding conditionsand/or drainage deficiencies.

1.06 WARRANTY INFORMATION

A. A manufacturer’s limited labor & material warranty is availableon eligible projects. Contact MPM Technical Support for details.

B. Limited warranties are not available for continuous immersionservice; cryogenic, freezer or cold storage facilities; or overexisting wet roofing materials. Other limitations may apply.

C. Inspections: Warranted projects are subject to:

1.Pre-job inspection and adhesion test.2. Final quality control inspection.3. Inspections may be performed by MPM or its designated third-

party inspectors at MPM’s discretion.D. Warranty submittals

1.MPM Warranty Pre-Approval Application2.Adhesion test results

PART 2 — PRODUCTS

2.01 SILICONE COATING

A. Enduris 3500 high solids, solvent-free, alkoxy-based, moisture-

Warranty Program for GE Enduris Silicone Coatings

GE Enduris 3500 High Solids Silicone

Roof Coating

*Enduris is a trademark of Momentive Performance Materials Inc.

cured, silicone roof coating supplied andmanufactured by Momentive Performance Materials,Inc., Waterford, NY.

B. Physical Properties shall be tested in accordance with ASTMD6694 as indicated in the table below.Property ASTM ValueTensile Strength D2370 200 psi minElongation at Break (73°F) 500% minVolume Solids D2697 90% minWeight Solids D1644 90% min

D2370

42

2.02 ASPHALT BLEED BLOCKER

A. GE Asphalt Bleed Blocker, Momentive Performance Materials,Waterford, NY. Refer to the GE Asphalt Bleed BlockerTechnical Data Sheet for physical property information.

2.03 SEAM TREATMENT MATERIALSA. GE Enduris Silicone Seam Sealant, Momentive Performance

Materials, Waterford, NY. Refer to the Enduris Seam SealantTechnical Data Sheet for physical property information.

B. GE UltraSpan* UST / USM pre-cured silicone transition sheets andmolded corners, Momentive Performance Materials, Waterford, NY.Refer to the UltraSpan Technical Data Sheet for physical propertyinformation.

C. Reinforcement Fabric: GE RF100 series is a 100% polyester spun-laced textile reinforcing fabric that is available in 4”, 6” or 12”widths. Refer to the RF100 Technical Data Sheet for physicalproperty information.

Warranty Program for GE Enduris Silicone Coatings

GE Enduris 3500 High Solids Silicone

Roof Coating

2.04 ACCESSORY MATERIALSA.

B. YellowWalkwayCoating:GESEC2400ProtectionYellowsiliconecoating.

Traffic Mats: Yellow Spaghetti (manufactured by Western Plastics, Inc. 800-325-3605) pressure bonded, non-woven pads (or in rolls) made of spaghetti-like strands of flexible polyvinyl chloride (PVC), nominal thickness 5/16".

PART 3 — EXECUTION

3.01 SURFACE PREPERATION BUR

A. The surface must be clean, sound, dry and free of any materials thatwould inhibit proper adhesion of the coating or sealant.Achievement of this condition may require the use of cleaner,scraping, power brooming, vacuuming or other means, and shallalways be performed observing responsible trade practices.

B. Rinse entire roof with power washer.

C. Any poorly adhered existing coating must be removed with apressure washer and clean tap water. Any coating that remainsthat is well adhered is allowable.

D. Required repairs to be executed in accordance with “RepairManual for Low-Slope Membrane Roof Systems”, published byNational Roofing Contractors Association, NCRA.

E. Coat entire roof with GE Asphalt Bleed Blocker at a rate of minimumone (1) gallon per 100 square feet.

*Enduris and Ultraspan are trademarks of Momentive Performance Materials Inc. 43

A. The surface must be clean, sound, dry and free of any materials that would inhibit proper adhesion of the coating or sealant. Achievement of this condition may require the use of cleaner, scraping, power brooming, vacuuming or other means, and shall always be performed observing responsible trade practices.

B. Any poorly adhered existing coating must be removed with a pressure washer and clean tap water. Any coating that remainsthat is well adhered is allowable.

C. Required repairs to be executed in accordance with “RepairManual for Low-Slope Membrane Roof Systems”, published byNational Roofing Contractors Association, NCRA.

D. Coat entire roof with GE Asphalt Bleed Blocker at a rate of minimumone (1) gallon per 100 square feet.

E. All blisters shall be cut, dried out, re-adhered and sealed withappropriate Enduris Seam Sealant or approved equal. Afterallowing sealant to dry, apply Enduris 3500 silicone roof coating andGE RF100 polyester reinforcing fabric as described below.

F. Reseal around all mechanical equipment and roof penetrationswith GE Enduris Silicone Seam Sealant or Enduris 3500 basecoat andRF100 polyester reinforcing fabric.

G. All loose seams, ridges and other membrane deficiencies of existingroof system shall be fastened down and sealed. Sealant must sealfasteners as well.

3.02 COATING APPLICATION

Warranty Program for GE Enduris Silicone Coatings

GE Enduris 3500 High Solids Silicone

Roof Coating

3.03 FINISHED COATING CHARACTERISTICS

A. The cured Enduris 3500 silicone roof coating should be monolithicand seamless, encapsulating the entire existing surface. Thecoating should be free of holidays, voids, pinholes and cracks.Apply additional coating as necessary to correct defects.

B. Minimum cured coating thickness is 28 mils DFT.

3.04 SAFETY REQUIREMENTS

A. Refer to appropriate SDSs for additional safety information.

B. Before starting to apply coating, primers or other materials, anypotential sources of air entry into the building must be sealedoff.

*Enduris is a trademark of Momentive Performance Materials Inc.

A. The Enduris 3500 roof coating shall be applied uniformly in one ormore coats at a theoretical application rate of 2.0 gallons/100 ft2 toachieve a WFT (wet film thickness) of 32 mils and a minimum total DFT(dry film thickness) of 28 mils. NOTE: Theoretical coating applicationrate is based strictly on minimum wet film thickness requirements andmust be increased for site-specific conditions such as surface texture,overspray loss, container and other residues, application techniqueand environmental conditions.

B. Required final DFT is 28 mils minimum on any given area of the roofsurface. Apply additional coating as needed to meet thisrequirement.

C. Additional coats: When additional applications of coating areneeded, allow sufficient cure time between applications to provide astable working surface. Subsequent coating should be applied in aspray, roller or brush pattern perpendicular to the previousapplication.

D. Equipment: Enduris 3500 silicone roof coating may be applied byspray equipment, roller, brush or gauge rake.

E. Cure: Enduris 3500 silicone roof coating cures by reacting withambient moisture. Cure time will be reduced at elevated ambienthumidity and temperatures.

44

3.05 CLEANUP

A. Keep all work areas clean, clear and free of debris at all times.

B. Do not allow trash, waste or debris to accumulate on the roof.Remove these items from the roof on a daily basis.

C. Collect and properly store all tools and unused materials at the endof each workday.

D. Dispose of or recycle all trash and excess material in a mannerconforming to current EPA regulations and local laws.

E. Properly clean the finished roof surface after completion and makesure the drains and gutters are not clogged.

F. Clean and restore all damaged surfaces to their original condition.

3.06 QUALITY CONTROL

A. Enduris 3500 silicone roof coating restoration projects are subject topre-job,progress and final inspections by MPM, its designated third-party inspectors, or others subject to warranty requirements andcontract documents.

Warranty Program for GE Enduris Silicone Coatings

GE Enduris 3500 High Solids Silicone

Roof Coating

DISCLAIMER:THE MATERIALS, PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC. AND ITS SUBSIDIARIES AND AFFILIATES (COLLECTIVELY “SUPPLIER”), ARE SOLD SUBJECT TO SUPPLIER’S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH, SUPPLIER MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (i) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS, OR (ii) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING ITS PRODUCTS, MATERIALS, SERVICES, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN SUPPLIER’S STANDARD CONDITIONS OF SALE, SUPPLIER AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS, PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user bears full responsibility for making its own determination as to the suitability of Supplier’s materials, services, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating Supplier’s products, materials, or services will be safe and suitable for or waive any provision of Supplier’s standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by Supplier. No statement contained herein concerning a possible or suggested use of any material, product, service or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of Supplier covering such use or design, or as a recommendation for the use of such material, product, service or design in the infringement of any patent or other intellectual property right.

GE is a trademark of General Electric Company and is used under license by Momentive Performance Materials Inc.Momentive and the Momentive logo are trademarks of Momentive Performance Materials Inc.*Enduris and UltraSpan are trademarks of Momentive Performance Materials Inc.Copyright 2016 Momentive Performance Materials Inc. All rights reserved.

WNT3500BUR15316

45