REPAIRING AND RENOVATION OF TOURISM COMPLEX, …

Sl No Description of work Rate in Figure and words Unit Amount

1 125.76 M3

Earth work excavation for foundation in all soils and sub-

soils and to full depth as may be directed except in rock

requiring blasting inclusive of shoring shuttering, bailing

out water wherever necessary and depositing the surplus

earth within the compound in places shown by the

departmental officers with an initial lead of 10 mts and

initial lift of 2 mts. and clearing and levelling the site, etc.,

complete complying with standard specification.

1 M3

(One Cubic

Meter)

2 148.84 M3

Supplying and filling in foundation, basement, etc with

filling sand in layers of not more than 15 cm thick well

watered, rammed and consolidated etc. complete

complying with standard specification and as directed by

the departmental officers.

1 M3

(One Cubic

Meter)

3 123.53 M3


Sand and Quarry rubbish in layers of not more than 15

cm thick well watered, rammed and consolidated etc.

complete complying with standard specification and as

directed by the departmental officers.

1 M3

(One Cubic

Meter)

REPAIRING AND RENOVATION OF TOURISM COMPLEX, POOMPUHAR, NAGAPATTINAM DISTRICT

Construction of New Tourism Complex for provision of following visitor amenities, Interpretation Centre, Restaurant,

Craft Bazaar, Cottages, Plaza and OHT

SCHEDULE-A

Qty

Signature of Contrator PROJECT ENGINEER

Sl No Description of work Rate in Figure and words Unit AmountQty

4 371.39 M2

Providing Pre - construction Anti - termite treatment and

creating a chemical barrier to the building by injecting

chemical emulsion of required concentration under grade

slab and grade beam, all round the Pile Caps, Catch

basins, trenches, pits, tunnels, wall trenches, back fill,

plinth filling, junction of wall and floor. External perimeter

of building, surrounding of pipes, expansion joints, below

U.G. sump and retaining/side walls etc. as per

instructions of chemical manufacturer as directed by the

Department officer/ Architect. The treatment shall be

carried out strictly in accordance with the technical

specification and conforming to IS 6313 or equivalent BS

specification. The chemical to be used as insecticide for

the treatment shall be Biflex Tc, TC stands for

Termiticide Concentrate for Termite Control (Bifenthrin)

and the application shall be diluted 1 part of chemical

Biflex Tc with 49 parts of water to get 0.05% emulsion

and strictly in accordance with the manufacturer’s

specification.Including cost of chemicals labour

charges,transport and storing etc complete and as

directed by the department officers

1 M2

(One Square

Meter)

5

Boring with hydraulic piling rigs with power units,

providing and installing cast in situ single under reamed

piles of specified diameter and length below pile cap in M-

30 cement concrete, to carry a safe working load not less

than specified, excluding the cost of steel reinforcement

but including the cost of boring with bentonite solution

and the length of the pile to be embedded in pile cap etc.

all complete.



a 390.00 RM

500mm dia1 RM

(One Running

Meter)

6 52.97 M3

Cement Concrete 1:5:10 (One Cement, Five sand and

Ten hard broken stone jelly) using 40 mm gauge hard

broken granite stone jelly for foundation including

dewatering wherever necessary and laid in layers of not

more than 15 cm thick well rammed, consolidated and

curing etc. complete complying with standard

specification

1 M3

(One Cubic

Meter)

7 67.64 M3

Plain Cement Concrete 1:3:6 (one cement, three sand

and six hard broken stone jelly) using 20mm jelly for

wearing coat including laying, compacting, finishing and

curing, etc., complete as per standard specificatins and

as directed by the departmental officers.

1 M3

(One Cubic

Meter)



8

Providing and lying in position , standardised Concrete

Mix M30 Grade in accordance with IS 456-2000 using

20mm and down graded hard broken granite stone jelly

for all RCC items of works with minimum cement content

of 325 Kg/M3 and Maximum water cement ratio of 0.55

including admixture (plasticiser/super plasticiser ) in

recommended proportions as per IS 9103 as accelerate ,

retard setting of concrete improve workability without

impairing strength and durability with about )5 cu.m )

7730 kg of 20mm machine crushed stone jelly and with

about (3.3 cu.m) 5156 kg of 10-12mm machine crushed

stone jelly and about (4.79 cu.m 7670 kg of sand , but

excluding cost of reinforcement grill and fabricating

charges centering and shuttering and also including

laying vibrating with mechanical vibrators finishing curing

ect., and providing fixtures like fan clamps in the RCC

floor /roof slabs wherever necessary without claiming

extra etc., complete complying with standard

specification and as directed by the departmental

officers. The coarse and fine aggregates to be used

should comply with the requirements of IS standards.

a 52.69 M3

a) Upto Basement 1 M3

(One Cubic

Meter)

b 19.00 M3

c) GF Column 1 M3

(One Cubic

Meter)

c 37.65 M3

d) Roof Beam GF lvl. 1 M3

(One Cubic

Meter)



d 4.09 M3

d) Beam FF lvl. 1 M3

(One Cubic

Meter)

e 58.79 M3

e)Roof Slab 1 M3

(One Cubic

Meter)

f 7.67 M3

f)Lintels and sunshades 1 M3

(One Cubic

Meter)

g 12.00 M3

g) Rcc Walls 1 M3

(One Cubic

Meter)

9 41.07 MT

Supplying, fabricating and placing in position Mild Steel /

Ribbed Tor Steel grills for all RCC works as per design

given including cost of steel and G.I. binding wire in all

floors etc. complete complying with standard

specification.

1 Mt

(One Metric

Tonne)

10

Supplying and erecting steel centering including

necessary supports for plane surfaces for Reinforced

Cement Concrete works such as column footings,

column pedestals, plinth beams, grade beams, staircase

steps, etc. which require only nominal strutting using mild

steel sheets of size 90cm x 60cm and 10 BG stiffened

with welded mild steel angles of size 25mm x 25mm x 3

mm for boarding, laid over silver oak joists of size 10cm

x 6.5cm spaced at about 75cm centre to centre or at

suitable intervals etc. complete in all floors complying

with standard specifcation.



a 356.58 M2

For column footing, plinth beam and raft slab etc., 1 M2

(One Square

Meter)

b 1,060.64 M2

For plane surfaces such as roof slab, lintel and beams

etc.,1 M

2

(One Square

Meter)

c 313.29 M2

For Rectangular or Square RCC columns, sunshades,

top and bottom slab of RCC boxing, etc..1 M

2

(One Square

Meter)

11

Brick work in following Cement Mortar 1:5 (One cent and

five sand) using best quality II class table moulded

chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" for all

floorsincluding curing, etc., complete complying with

standard specification.

a 17.92 M3

Foundation and basement 1 M3

(One Cubic

Meter)

b 151.81 M3

IN Ground Floor 1 M3

(One Cubic

Meter)

12 16.00 M2

Brick partition walls of 11.50cm thickness using best

quality II class table moulded chamber burnt bricks of

size 9" x 4-3/8" x 2-3/4" in Cement Mortar 1:3 (One

Cement and Three Sand) using hoop iron reinforcement

if found necessary including curing etc. complete and as


1 M2

(One Square

Meter)



13 575.00 M2

Special ceiling plastering with Cement Mortar 1:3 (One

Cement and Three Sand) 10mm thick and finishing the

exposed surface of all RCC items of work such as slabs,

beams, sunshades, facia, canopy slab, staircase waist

slab, landing slab etc., including hacking the surfaces,

providing cement mortar nosing, beading for sunshades,

staircases, steps, landing slabs and curing, etc., in all

floors complying with standard specification and as

directed by the departmental officers

1 M2

(One Square

Meter)

14 1,376.27 M2

Plastering with Cement Mortar 1:5 (One cement and

Five sand), 12mm thick in all floors including curing etc.,



1 M2

(One Square

Meter)

15 116.50 M2


Three sand),20mm thick- mixed with red oxide

including cost and conveyance of all materials and all

labour charges,curing etc., complete complying with

standard specifications.

1 M2

(One Square

Meter)

16

Supply and fixing II class Teak wood scantlings frames

for doors, windows, ventilators and other similar joinery

works including all material and labour charges for teak

wood wrought and put up in position as per the architural

drawings & Specification

a 1.09 M3

Teak Wood Scantlings below 2m in length 1 M3

(One Cubic

Meter)

b 1.05 M3

Teak Wood Scantlings 2m to 3m in length 1 M3

(One Cubic

Meter)



17 5.08 M3

Supply and fixing Country wood scantlings for roofing

timber including all material such as labour charges for

Country wood, wrought and put up in position and the

size and section as per the architural drawings &

Specification

1 M3

(One Cubic

Meter)

18 13.32 M2

Supplying and fixing in postion of 35mm thick solid core

flush door shutters single leaf with TW ply on both sides

and with TW lipping of size 35x12mm on all edges with

necessary adhesives and C.P. Screws Alu. Butt Hinges

(3 nos. 250 x 16 mm Size) Alu. A

1 M2

(One Square

Meter)

19

Supply and fixing T.W panelled door shutter with

ornamental design of required size using 150mmx40mm

scantlings for style and bottom,middle

rails,230mmx40mm scantlings for top rail and 25mm

thick planks for panelling. The rate is including polishing

with melamine polish , supply and fixing furniture fittings

such as 150mmx25mmBrass hinges-3

nos,200mmx12mm Brass tower bolt -2 nos,Brass door

stopper-1 no and Brass ornamental handles for inner

and front etc., as directed by the corporation officers

complying with standard specification. Burma Teak wood

Heritage style

a 12.70 M2 Double leaf shutter1 M

2

(One Square

Meter)

20 67.70 M2

Supplying and fixing Teak Wood Framed Glazed

Window Shuttars including all materials and labour for

wrought and put up in position and brass furniture fittings

such as 3'' hookreye3'' hinges and 3'' Towar bolts with

necessary scrows etc.., Complete.

1 M2

(One Square

Meter)



21 8.40 M2

Supplying and fixing in position of T.W Louvered

Ventilator including cost of 3mm pin headed glass,12mm

of M.S bars and labour charges for making holeand

holdeds on sides etc., complete.

1 M2

(One Square

Meter)

22 139.50 M2

Flooring with following Authankudy tiles of size 10" x 10"

x 3/4" laid over cement mortar 1:3 (One Cement and

Three Sand) 20 mm thick base mortar over the existing

slab / floor including cutting the tiles to the required size

with special cutter wherever necessary, laying in position

and pointing with white cement mixed with colouring

pigment at the rate of 0.3 Kg. / sq.m. etc., complete

complying with standard specification.

1 M2

(One Square

Meter)

23 57.00 M2

Flooring with following ceramic tiles of size 305 x 305 x 6

mm laid over 20 mm thick cement mortar 1:3 (One

Cement and Three Sand) base mortar over the existing

slab / floor including cutting the tiles to the required size

with special cutter wherever necessary, laying in position

and pointing with white cement mixed with colouring

pigment at the rate of 0.3 Kg. / sq.m. etc., complete


1 M2

(One Square

Meter)

24 76.50 M2

Dadooing walls with 300mm x 450mm x 8mm with best

approved quality, white / colour glazed tiles set in

Cement Mortar 1:2 (One Cement and Two sand) 10mm

thick and pointing the joints with white cement mixed with

colouring pigments at the rate of 0.40 Kg. / sq.m. neatly

in all floors, curing, etc., complying with standard


officers.

1 M2

(One Square

Meter)



25 160.32 M2

Paving the floor with Clay tiles (anti-skid tiles) of 20mm

thick of approved quality and colour laid in Cement

Mortar 1:3 (One Cement and Three sand) 20mm thick

and pointing with colour cement at the rate of0.40 Kg. /

sq.m and mixing with colouring pigment at the

rate0.30kg/ sq.m including finishing complete complying

with standard specification and as directed by the

departmental officers.

1 M2

(One Square

Meter)

26 550.00 M2

Supplying and laying of plain Paver Block 80 mm thick,

including compacting with plate compactor (or) Roller

compactor including cost and conveyance of all materials

and all labour charges, curing etc,complete.

1 M2

(One Square

Meter)

27 40.00 M2

Paving the Dry stone floor with Granite slab of size 450 X

450mm and 70mm thick) incluiding cutting and leveling

the earth for Landscapping area stepper over well

compacted earth etc all complete complying with

standarad specification (natural stone).

1 M2

(One Square

Meter)

28 550.98 M2

Finishing the top of slopped roof, sun-shade with

Mangalore Tiles of approved quality laid in cement

mortar 1:3 20mm thick mixed with WPC at 2% by weight

of cement used and top pointed with the same red oxide

mixed mortar etc complete, complying with standard

specifications

1 M2

(One Square

Meter)



29 50.00 M2

Finishing the top of roof with one course of machine

pressed tiles of size 230mm x 230mm x 20mm of

approved quality set in Cement Mortar 1:3 (One Cement

and Three Sand) 12mm thick mixed with water proofing

compound conforming to ISS at 2% by weight of cement

used and the joints pointed neatly to full depth of tiles

with the same cement mortar mixed with red oxide and

water proofing compound including curing etc., complete


the departmental officers

1 M2

(One Square

Meter)

30 6.00 M3

Weathering course in brick jelly lime concrete using

broken brick jelly of size 20mm uniform gauge in pure

slaked lime (no sand to be used) to the proportion of

brick jelly to lime being 32:12.5 by volume and laid over

the RCC roof slab in a single layer of required slope and

finished by beating the concrete with wooden beaters of

approved pattern, keeping the surface constantly wet by

sprinkling lime jaggery water, etc., complete as per

standard specification and as directed by the

deparmental officers.

1 M3

(One Cubic

Meter)

31 2,240.97 KG

Supplying and fixing in position of M.S grills for windows

and ventilators of approved design including cost of

material, labour charges fixing and one coat of primer

etc.,complete.

1 Kg (One

Kilogram)

32 37.00 M2

Supplying and erecting pull and push type rolling shutter

with ISI make of approved size and section using 18 GI

sheet. The shutter shall be painted with one coat of red

oxide primer and the rate is inclusive of hood covers,

transportation charges etc., Manually operated

1 M2

(One Square

Meter)



33 236.00 M2

Providing mangalore tile roofing over one coarse of flat

Ceiling tiles with necessary ridges etc all complet with

out roof timber inclu lime mortar and tw reeper Including

cost all material etc all complete as directed

1 M2

(One Square

Meter)

34 1,262.00 M2

White washing two coats with freshly burnt white shell

lime in all floors including cost of lime, blue powder

fevicol type gum, brushes, scaffolding charges, etc.,


directed.

1 M2

(One Square

Meter)

35 222.50 M2

Painting two coats of newly plastered wall surface with

two coats of approved cement paint over one coat of

white cement of approved colour over a priming coat

including thorough scrapping, clean removal of dirt, and

including necessary touch up wherever required etc.,


1 M2

(One Square

Meter)

36 643.96 M2

Supplying and painting the walls with two coats of oil

bound distemper over one coat of water based cement

primer including cost for distemper, primer, cleaning and

scrapping the walls, rendering the walls smooth with

necessary putty, brushes, scaffolding arrangements,

labour charges, etc., as per standard specification.

1 M2

(One Square

Meter)



37 549.00 M2


ready mixed plastic emulsion paint of first class quality

and of approved colour over a priming coat including

thorough scrapping, clean removal of dirt, and including

necessary plaster of paris putty, wherever required etc.,


1 M2

(One Square

Meter)

38 92.00 M2

Painting new iron works such as steel doors, windows,

ventilators, window bars, balustrades etc., with two coats

of best approved first quality and colour of synthetic

enamel paint over the existing red oxide priming coat in

all floors excluding cost of priming coat etc., complete


1 M2

(One Square

Meter)

39 249.89 M2

Painting new wood work with two finishing coats of

synthetic enamel ready mixed paint of approved quality

and colour over one coat priming coat in all floors

including the cost of primer etc., complete complying with


1 M2

(One Square

Meter)

40 17.00 M2

Polishing the teak wood door with two coats of best

French (Lac) polish with approved quality and brand over

a coat of bee's waxing including preparing the wooden

surface to receive polishing, etc., complete complying as

per the standard specifications.

1 M2

(One Square

Meter)



PLUMBING WORKS

41 6.00 Nos

Supplying and fixing in position White / Colour Special

Delux Model Glazed Cascade Type Parryware /

Hindware /Equivalent Wall Mounted European Water

Closet of best quality and approved make with 100mm

“P” or “S” trap connecting with CI pipe of 100mm dia /

PVC pipe of 110mm dia, double flapped rigid PVC black

seat and seat cover with

CP brass hinges including cost of white cement, cement

for packing, spun yarn, teak wood plugs, brass screws,

etc., including supplying and fixing 10 litres capacity PVC

/ 12.5 litres capacity porcelin low level flushing tank with

a pair of CI brackets, etc., complete with all fittings, such

as, 15mm brass ball valve with polythene float with brass

handle, union coupling connected by means of 40mm

white PVC flush hand

using indian adopter joint including all internal fittings,

such as, 15mm bras connections, 15mm GM wheel

valve, 15mm brass nipple (2 Nos.), 15mm nylon

connection, TW plugs, screws and also giving necessary

connection to the PVC pipe and painting the CI brackets

with 2 coats of approved paint over one coat of red oxide

primer, dismantling the masonry and re-doing the

dismantled masonry to original condition,

etc., complete complying with standard specifications.

(The EWC and flushing tank with all accessories should

be got approved by the Executive Engineer before use

on works) with 10 litres capacity flushing tank with all

internal dual flush fittings with normal seat cover

1 No (One

Number)



42 3.00 Nos

Providing and fixing Lipped mouth flat back urinal of

approx. size 382 x 398 x601 mm having pre & post

flushing with water (250 ml & 500 ml consumption),

having water inlet from back side, including fixing to wall

with suitable brackets all as per manufacturers

specification and direction of Engineer-in-charge.

1 No (One

Number)

43 8.00 Nos

Wash Hand Basin of size 550mm x 400mm with all

accessories such as Cast Iron Brackets, 32mm dia CP

Waste Coupling, Rubber Plug and Chain, 32mm dia 'B'

Class GI Waste Pipe, 15mm dia GM Wheel Valve,

15mm dia Nylon Connection, 15mm dia Brass Nipples,

15mm CP Pillar Tap etc

1 No (One

Number)

44 8.00 Nos

Providing and fixing CP Brass 32mm size Bottle Trap of

approved quality & make and as per the direction of

Engineerin-charge.

1 No (One

Number)

45 8.00 Nos

Special type mirror of size 1000 x 780 mm 1 No (One

Number)

46 6.00 Nos

Providing and fixing toilet paper holder(CP brass)1 No (One

Number)

47 Providing & fixing pipes.

a 35.00 RM Sand cast iron S&S pipe as per IS: 1729

1 RM

(One Running

Meter)

b 70.00 RM Sand cast iron S&S pipe as per IS: 1729

1 RM

(One Running

Meter)



48

Providing and fixing M.S. holder-bat clamps of approved

design to Sand Cast iron/cast iron (spun) pipe embedded

in and including cement concrete blocks 10x10x10 cm of

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone

aggregate 20 mm nominal size), including cost of cutting

holes and making good the walls etc. :

a 18.00 RM For 100 mm dia pipe

1 RM

(One Running

Meter)

b 35.00 RM

For 75 mm dia pipe 1 RM

(One Running

Meter)

49

Providing & fixing sand cast iron S&S trap of self

cleaning design with sand cast iron screwed down or

hinged grating with or without vent arm complete,

including cost of cutting & making good the walls and

floors.

a 10.00 Each

100 mm inlet & 75 mm outlet

Each

50

Providing & fixing plain sand cast iron S & S Bend of

required degree.

a 4.00 Each

100 mm dia

Each



b 5.00 Each

100 x 100 x 100 mm

Each

c 10.00 Each

75 * 75 * 75 mm

Each

51

Providing and fixing Chlorinated Polyvinyl Chloride

(CPVC) pipes,having thermal stability for hot & cold

water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step

CPVC solvent cement and the cost of cutting chases and

making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work, including cutting chases and making

good the walls etc.

a 25.00 RM 25mm dia nominal bore1 RM

(One Running

Meter)

b 20.00 RM 32mm dia nominal bore1 RM

(One Running

Meter)



52

Providing & fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end)

a 1.00 Each

25 mm nominal bore

Each

b 1.00 Each

32 mm nominal bore

Each

53

Providing and fixing wheel valve (brass) of approved

quality complete. (High or low pressure with plastic

floats).

a 1.00 Each25 mm nominal bore

Each

b 1.00 Each32 mm nominal bore

Each

54 8.00 Each

Providing and fixing 15 mm nominal bore C.P brass long

nose bib cock of approved quality conforming to IS

standards and weighing not less than 810 gms.

Each

55 17.00 Each

Providing & fixing 15 mm nominal bore C.P brass angle

valve for basin mixer and geyser points of approved

quality conforming to IS 8931.

Each



56 2.00 Each

Constructing masonry Chamber 60x60x75 cm inside, in

brick work in cement mortar 1:4 (1 cement : 4 coarse

sand) for sluice valve, with C.I. surface box 100mm top

diameter, 160 mm bottom diameter and 180 mm deep (

inside) with chained lid and RCC top slab 1:2:4 mix (1

cement : 2 coarse sand : 4 graded stone aggregate

20mm nominal size ) , i/c necessary excavation,

foundation concrete 1:5:10 (1 cement : 5 fine sand : 10

graded stone aggregate 40 mm nominal size) and inside

plastering with cement mortar 1:3 (1 cement : 3 coarse

sand) 12 mm thick, finished with a floating coat of neat

cement complete as per standard design

Each

57

Excavating trenches in all kind of soil of required width

for pipes. including excavation for sockets and dressing

of sides, ramming of bottoms, including getting out the

excavated soil & then returning the soil as required, in

layers not exceeding 20 cm in depth including

consolidating each deposited layer by ramming,

watering, etc & disposing of surplus excavated soil as

directed within a lead of 50m.

a 40.00 RM Pipes 80 mm to 300 mm diameter1 RM

(One Running

Meter)

58

Providing, laying and jointing glazed stone ware pipes

grade `A' with stiff mixture of cement mortar in the

proportion of 1:1 (1cement :1 fine sand) including

testing of joints etc complete.



a 40.00 RM 150 mm diameter 1 RM

(One Running

Meter)

59

Providing and laying cement concrete 1 : 5 : 10 (1

cement : 5 coarse sand : 10 gradded stone aggregate

40 mm nominal size) alround S.W. Pipes including bed

concrete as per standard design.

a 40.00 RM 150 mm diameter S.W.Pipe1 RM

(One Running

Meter)

60 6.00 Nos

Constructing brick masonry manhole with F.P.S. bricks

in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC

top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4

grade stone aggregate 20mm nominal size); foundation

concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded

stone aggregate 40 mm nominal size) inside

plastering 12 mm thick with cement mortar 1:3

(1cement 3 coarse sand ) finished with a floating coat of

neat cement and making channels in cement concrete

1:2:4 (1cement : 2 coarse sand: 4 graded stone

aggregate 20 mm nominal size) finishd with a floating

coat of neat cement complete as per standard design.

Inside size 90 x 80 cm & 45 cm deep including CI cover

with frame (light duty) 455 x 610mm internal dimension

total wt. of cover & frame to be not less than 38 kg (wt.

of cover 23 kg and wt. of frame 15 kg)

1 No

(One Number)



a 2.00 RMExtra for depth for manhole with F.P.S. bricks size 90 X

80 cm

1 RM

(One Running

Meter)

61

Providing and fixing square mouth S. W. Gully trap

grade `A' complete with C.I. grating brick masonry

chamber with F.P.S bricks and water tight CI cover with

frame of 300 x 300 mm size (inside) the weight of cover

to be not less than 4.50 kg and frame to be not less than

2.70 kg as per standard design

a 2.00 Each

180 x 150 mm. size P type

Each

62 2.00 Each

Making soak-pit 2.5 m. diameter and 3 m. deep with 45 x

45cm dry brick honey comb shaft with F.P.S bricks

and SW drain pipe complete as per standard design. Each

63 5,000.00 Lt

Providing and placing on terrace (at all floor levels)

polyethylene water

storage tank, IS : 12701 marked, with cover and suitable

locking arrangement and making necessary holes for

inlet, outlet and overflow pipes but without fittings and

the base support for tank.

Lit.

(One Liter)

64 130.00 RM

Providing and laying non-pressure NP2 class(light duty)

R.C.C. pipes with collars jointed withstiff mixture of

cement mortar in the proportionof 1:2 (1 cement : 2 fine

sand) including testing of joints etc. complete : 300 mm

dia. R.C.C. Pipe

1 RM

(One Running

Meter)

65 1.00 Each

Making rain water pit 2.5m diametre 3.0 metre deep with

45x45cm dry brick honey. Each



66 2,238.00 RM

Supply and run of 2 of 2.5 sqmm (36/0.3) PVC insulated

SC unsheathed Cu.Conductor of 1100V Grade in

suitable PVC rigid pipe in wall and ceiling with

continuous earth wire connection 1 of 1.5 sqmm (22

/0.3) PVC insulated SC unsheathed Cu.Conductor of

1100V grade and making good of the concealed portion

with suitable colour.

1 RM

(One Running

Meter)

67 700.00 RM

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated

SC unsheathed Cu.Conductor of 1100V Grade in

suitable PVC rigid pipe in wall and ceiling with

continuous earth wire connection 1 of 2.5 sqmm (36

/0.3) PVC insulated SC unsheathed Cu.Conductor of

1100V grade and making good of the concealed portion

with suitable colour.

1 RM

(One Running

Meter)

CABLES

68 80.00 RM

Supply and laying of 4C X 6 sq.mm Al XLPE armoured

LTUG cable in a trench to be excavated at a depth of

0.75 metre putting 0.15 mt. Layer of sand and covering

the cable completely with bricks and sand and refilling

the earth to make good.

1 RM

(One Running

Meter)

CLAMPING

69 30.00 RM

Supply and Clamping of 4C X 10 sqmm Al XLPE LTUG

Armoured LTUG cable on post or on wall and MS Clamp

with necessary accessories etc

1 RM (One

Running

Meter)

CABLE GLAND

70 4.00 Each

Supply and fixing of brass cable gland for4C x 10 sq.mm

PVC LTUG armoured cable with earth connection with

necessary accessories etc Each

ELECTRICAL



EARTHING

71 160.00 RM

Supply and run of 2 of No.8 SWG GI wire for guarding

with cradle with No.8SWG GI wire at the equal interval of

1.5 meter and etc to complete the work

1 RM (One

Running

Meter)

72 1.00 Each

4WAY 3 PHASE HORIZONTAL MCB DB (3 Tier )

Supply and erection of powder coated wall mounting

TPN DB made of 1.6mm thick CRCA sheet steel dust

and vermin proof enclosure with suitable size of bus bar

with suitable bus insulators and sleeve for main and

interconnecting Switchgear, earthing as per requirement

of CEIG and IE regulation. For the provision of following

rated switchgear in the panel.(SD)

Incoming :

40A 4P ISO - 1 No

Outgoing :

30mA RCCB - 3 Nos

10w 20A - 12 Nos

Each

73 26.00 EachSupply,installation and commissioning 4 feet 40W Tube

Fitting with TW round blocks on wall or ceiling Each

74 9.00 EachSupply and fixing Decorative wall light of 15 w (Philips

Havels).(color will be selected by architect)Each

75 13.00 Each

Supply, installation, testing and commissioning of 48"

sweep 250watts 1400 RPM, 2400 CMH ceiling fan with

single phase induction motor for continuous duty suitable

for operation on 230 Volts single phase 50c/s system

complete etc.

Each

76 20.00 Each

Supply,installation and commissioning of 2 nos of 6A 5

pin Modular type wall universal socket with 2 no of 6A

Modular switch concealed in suitable MS box,in flush

with wall and etc to complete the work

Each



77 8.00 Each

Supply,installation and commissioning of 6A / 20A 3 pin

combined Modular type wall socket with 20A modular

type switch on suitable Modular plate and frame with MS

flush box and etc to complete the work

Each

78 1.00 Each

Supply & Fixing of 8 way single pole and neutral MCB

Sheet steel enclosure DB 1 no 40 Amps MCB as

incoming and 6 nos 20 Amps outgoing in flush with wall

and making good of the concealed portion with earth

connection only. The MCB DB and MCB's should be with

ISI mark (Like Standard Make) SD-167

Each

79 25.00 EachSupply and fixing suspended- pendant light of 20w for

decorative purpose Each

80 39.00 EachSupply and fixing of 18w LED 3000k round type

recessed type fitting Each

81 10.00 Each

Supply, Installation, testsing and commissioning of Track

light of 4 nos of 20w focus light in it for display lights Each

82 408.00 M2 Provision for fire safety as per CPWD SOR1 M

2

(One Square

Meter)

83 20.00 EachProvision of cut stone pillars , wall plates and base (1 at

each column location)Each



1 18.00 M3

Earth work excavation for foundation in all soils and sub-

soils and to full depth as may be directed except in rock

requiring blasting inclusive of shoring shuttering, bailing

out water wherever necessary and depositing the surplus

earth within the compound in places shown by the

departmental officers with an initial lead of 10 mts and

initial lift of 2 mts. and clearing and levelling the site, etc.,


1 M3

(One

Cubic Meter)

2 1.00 M3


filling sand in layers of not more than 15 cm thick well

watered, rammed and consolidated etc. complete


the departmental officers.

1 M3

(One

Cubic Meter)

3 3.00 M3

Providing and laying random rubble soling with hard

stone in foundation and plinth in cement mortar 1:6 (1

cement: 6 Sand)

1 M3

(One

Cubic Meter)

4 8.00 M3

Plan Cement Concrete 1:4:8(One Cement Four sand

Eight aggregates) using 40mm gauge HBG jelly

inclusive of shoring strutting and baling out water where

ever necessary ramming curing etc., complete in

respects complying with relevant standard specification

and as directed by the Department Officers.

1 M3

(One

Cubic Meter)

Renovation of work, signages and Drinking water facilities

SCHEDULE - B



5 1.00 M3

Cement Concrete 1:5:10 (One Cement, Five sand and

Ten hard broken stone jelly) using 40 mm gauge hard

broken granite stone jelly for foundation including

dewatering wherever necessary and laid in layers of not

more than 15 cm thick well rammed, consolidated and

curing etc. complete complying with standard

specification

1 M3

(One

Cubic Meter)

6

Providing and lying in position , standardised Concrete

Mix M30 Grade in accordance with IS 456-2000 using

20mm and down graded hard broken granite stone jelly

for all RCC items of works with minimum cement content

of 325 Kg/M3 and Maximum water cement ratio of 0.55

including admixture (plasticiser/super plasticiser ) in

recommended proportions as per IS 9103 as accelerate ,

retard setting of concrete improve workability without

impairing strength and durability with about )5 cu.m )

7730 kg of 20mm machine crushed stone jelly and with

about (3.3 cu.m) 5156 kg of 10-12mm machine crushed

stone jelly and about (4.79 cu.m 7670 kg of sand , but

excluding cost of reinforcement grill and fabricating

charges centering and shuttering and also including

laying vibrating with mechanical vibrators finishing curing

ect., and providing fixtures like fan clamps in the RCC

floor /roof slabs wherever necessary without claiming

extra etc., complete complying with standard


officers. The coarse and fine aggregates to be used

should comply with the requirements of IS standards



a 7.00 M3 a) Upto Basement1 M

3 (One

Cubic Meter)

b 9.00 M3 b) Ground floor1 M

3 (One

Cubic Meter)

7

Supplying and erecting steel centering including

necessary supports for plane surfaces for Reinforced

Cement Concrete works such as column footings,

column pedestals, plinth beams, grade beams, staircase

steps, etc. which require only nominal strutting using mild

steel sheets of size 90cm x 60cm and 10 BG stiffened

with welded mild steel angles of size 25mm x 25mm x 3

mm for boarding, laid over silver oak joists of size 10cm

x 6.5cm spaced at about 75cm centre to centre or at

suitable intervals etc. complete in all floors complying

with standard specifcation.

a 26.00 M2 For column footing, plinth beam and raft slab etc.,1 M

2

(One Square

Meter)

b 193.00 M2For plane surfaces such as roof slab, lintel and beams

etc.,

1 M2

(One Square

Meter)

c 15.96 M2

For Rectangular or Square RCC columns, sunshades,

top and bottom slab of RCC boxing, etc..1 M

2

(One Square

Meter)

8 15.96 M2


Five sand), 12mm thick in all floors including curing etc.,



1 M2

(One Square

Meter)



9 1220.23 M2

Pointing the stone work with cement mortar 1:3 (one

cement and three fine sand) to full depth using riversand

including curing and finishing complying with standard


Officers etc., complete.

1 M2

(One Square

Meter)

10

Supply and fixing II class Teak wood scantlings frames

for doors, windows, ventilators and other similar joinery

works including all material and labour charges for teak

wood wrought and put up in position as per the architural

drawings & specification

a 0.79 M3 Teak Wood Scantlings below 2m in length1 M

3 (One

Cubic Meter)

11

Supply and fixing T.W panelled door shutter with

ornamental design of required size using 150mmx40mm

scantlings for style and bottom,middle

rails,230mmx40mm scantlings for top rail and 25mm

thick planks for panelling. The rate is including polishing

with melamine polish , supply and fixing furniture fittings

such as 150mmx25mm Brass hinges- 3

nos,200mmx12mm Brass tower bolt -2 nos,Brass door

stopper-1 no and Brass ornamental handles for inner

and front etc., as directed by the departmental officers

complying with standard specification. Burma Teak wood

Heritage style

a 14.40 M2 Double leaf shutter1 M

2

(One Square

Meter)



12 12.96 M2

Supplying and fixing Teak Wood Framed Glazed

Window Shuttars including all materials and labour for

wrought and put up in position and brass furniture fittings

such as 3'' hookreye3'' hinges and 3'' Towar bolts with

necessary scrows etc.., Complete.

1 M2

(One Square

Meter)

13 48.48 M2

Paving the floor with C.C.Laminated tiles (Like Dora,

Eurocon tiles etc.,) anti-skid tiles (Required shape and

design) of 20mm thick of approved quality and colour laid

in Cement Mortar 1:3 (One Cement and Three sand)

20mm thick and pointing with colour cement at the rate

of0.40 Kg. / sq.m and mixing with colouring pigment at

the rate0.30kg/ sq.m including finishing complete


the departmental officers. (The make and brand of the

tiles should be got approved by Departmental Officer

before use on works)

1 M2

(One Square

Meter)



14 51.23 M2

providing and laying on the surface with best approved

quality fine polished Granite Stone Slabs for floor 18 /

20mm thick of Rubby Red and similar varieties with

machine cut edges laid over a cement mortar bed of

20mm thick using cement mortar 1:3 (One cement and

three sand) fixing the slabs with required cement slurry

and laid in true right angles with minimum possible width

of joints and pointing the joints with white cement mixed

with mathcing colouring pigments etc., The granite stone

slabs and other materials to be used shall be got

approved by the Departmental Officer concerned before

use on work, etc., complete as per standard

speicification.

1 M2

(One Square

Meter)

15 3.39 M2

Providing and fixing granite circular column with all the

detail as original sculpted out, as per directions of

Conservation architect and engineer in charge

1 M2

(One Square

Meter)

16 36.00 M2

Supply and installation of wall cladding with Glossy finish

granite stones with cutting edges and drilling holes and

fixing the clip with nails of the wall or Column and Install

the granite laid over a clip using required materials and

laid in true right angles with minimum possible width of

joints and pointing the joints with white cement mixed

with mathcing colouring pigments etc., The granite stone

slabs and other materials to be used shall be got

approved by the Departmental Officer concerned before

use on work, etc., complete and complying as per

standard speicification.

1 M2

(One Square

Meter)



17 138.60 M2

Paving the Dry stone floor with Granite slab of size 450 X

450mm and 70mm thick) incluiding cutting and leveling

the earth for Landscapping area stepper over well

compacted earth etc all complete complying with

standarad specification (natural stone).

1 M2

(One Square

Meter)

18 572.00 M2

Finishing the top of roof with one course of machine

pressed tiles of size 230mm x 230mm x 20mm of

approved quality set in Cement Mortar 1:3 (One Cement

and Three Sand) 12mm thick mixed with water proofing

compound conforming to ISS at 2% by weight of cement

used and the joints pointed neatly to full depth of tiles

with the same cement mortar mixed with red oxide and

water proofing compound including curing etc., complete


the departmental officers

1 M2

(One Square

Meter)

19 3360.00 M2


two coats of approved cement paint over one coat of

white cement of approved colour over a priming coat

including thorough scrapping, clean removal of dirt, and

including necessary touch up wherever required etc.,


1 M2

(One Square

Meter)

20 54.72 M2

Painting new wood work with two finishing coats of

synthetic enamel ready mixed paint of approved quality

and colour over one coat priming coat in all floors

including the cost of primer etc., complete complying with

standard specification. (The make, quality and colour of

paint should be got approved by the Departmental

Officer before use on works.)

1 M2

(One Square

Meter)



21 117.96 M2

Clean removal of Cement plaster from walls and racking

out joints 20mm deep, etc., complete complying with


1 M2

(One Square

Meter)

22 8.48 M2

Dismantling tile work in floors and roofs laid in cement

mortar including stacking material within 50 metres lead.

etc., complete complying with standard specification.

1 M2

(One Square

Meter)

23 41.84 M3

Demolishing R.C.C. work manually/ by mechanical

means including stacking of steel bars and disposal of

unserviceable material within 50 metres lead as per

direction of Engineer - in- charge. etc., complete


1 M3

(One

Cubic Meter)

24 387.00 M2

Repairs to plaster of thickness 12 mm to 20 mm in

patches of area 2.5 sq. meters and under, including

cutting the patch in proper shape, raking out joints,

preparing and plastering the surface of the walls

complete, including disposal of rubbish to the dumping

ground, all complete as per direction of Engineer-in-

Charge. 14.1.2 With cement mortar 1:4 (1cement: 4

coarse sand)

1 M2

(One Square

Meter)

25 107.57 M2

Chipping of unsound/weak concrete material from slabs,

beams, columns etc. with manual Chisel and/ or by

standard power driven percussion type or of approved

make including tapering of all edges, making square

shoulders of cavities including cleaning the exposed

concrete surface and reinforcement with wire brushes

etc. and disposal of debris for all lead and lifts all

complete as per direction of Engineer-In-Charge etc.,

complete complying with standard specification.75mm

average thickness

1 M2

(One Square

Meter)



26 260.00 RM

Cleaning of reinforcement from rust from the reinforcing

bars to give it a total rust free steel surface by using

alkaline chemical rust remover of approved make with

paint brush and removing loose particles after 24 hours

of its application with wire brush and thoroughly washing

with water and allowing it to dry, all complete as per

direction of Engineer-In-Charge.etc., complete complying

with standard specification

Bars above 12 mm diameter metre

1 RM

(One

Running

Meter)

27 668.00 M2

Demolishing brick tile covering in terracing including

stacking of serviceable material and disposal of

unserviceable material within 50 metres lead etc.,


1 M2

(One Square

Meter)

28 11999.46 M2

Surface dressing of the ground including removing

vegetation and inequalities not exceeding 15 cm deep

and disposal of rubbish, lead up to 50 m and lift up to 1.5

m. etc., complete complying with standard specification.

1 M2

(One Square

Meter)

29 107.57 M2

Providing, mixing and applying bonding coat of approved

adhesive on chipped portion of RCC as per

specifications and direction of Engineer-In-charge

complete in all respect Epoxy bonding adhesive having

coverage 2.20 sqm/kg of approved make etc., complete


1 M2

(One Square

Meter)



30 107.57 M2

Providing, mixing and applying SBR polymer (of

approved make @ minimum 2% by wt. of cement used)

modified plain/reinforced cement concrete for structural

members having minimum characteristic compressive

strength [with ordinary portland cement, coarse sand and

graded stone aggregate of 10mm maximum size in

proportion as per design criteria] with specified average

thickness.(CPWD 26.33.2 Vol-II) 75mm thick in Grade M

25 with cement content not less than 330 kg per cum

1 M2

(One Square

Meter)

31 1000.00 Kg

Providing and injecting approved grout in proportion

recommended by the manufacturer into cracks/honey-

comb area of concrete/masonry by suitable gun/pump at

required pressure including cutting of nipples after curing

etc. complete as per directions of Engineerin-

Charge.(CPWD 26.35.2 Vol-II). Stirrer mixed SBR

Polymer (of approved make) modified Cement slurry

made with Shrinkage Compensating Cement in

concrete/RCC work.

1 Kg (One

Kilogram)



SIGNAGES

32 16.92 M2

Providing and fixing cultural board madeup of 2mm thick,

304 grade stainless steel sheet powder coated of

required dimensions of Max 900mmx1275mm with given

information painted on it, and made in given profile as

shown in dwg including cost of all Labours and Materials

etc complete.

1 M2

(One Square

Meter)

Informative Signage

33 5.00 M3

Providing stone slab of Sectional Dimension 1000mm x

2500mm x (Tapered from 200mm bottom to 75mm at top

) with cutted to required dimension and fine dressed

above the ground level and 700 mm embeded in

concrete with all lead ,lift loading,unloading and

transportation etc complete.

1 M3

(One

Cubic Meter)

DIRECTIONAL SIGNAGE

34 0.47 M3

Providing stone Pillar of 200mm x 200mm x 2350mm

with cutted to required dimension and fine dressed

above the ground level and 900 mm embeded in

concrete with all lead ,lift loading,unloading and

transportation etc complete.

1 M3

(One

Cubic Meter)

a 0.36 M3

Providing stone Pillar of 150mm x 150mm x 750mm with

cutted to required dimension and fine dressed with all

lead ,lift loading,unloading and transportation etc

complete.

1 M3

(One

Cubic Meter)

b 1.69 M2

Providing Way finding signage board madeup of 2mm

thick, 304 grade powder coated stainless steel sheet of

required dimensions of Max 450mmx750mm with given

information powder coated on it, and made in given

profile as shown in dwg including fixing to the granite

pillar using clamps, cost of all Labours and Materials etc

complete.

1 M2

(One Square

Meter)



c 7.50 RM

Providing and fixing 20mm thick threaded SS rod to join

all the stone blocks to form one assembly as per drawing

and detail.

1 RM

(One

Running

Meter)

CAUTIONARY SIGNAGE

35 0.26 M3

Providing Granite Stone pillar 1 nos of dimension

150mmx150mmx1450 mm with necessary stone

moulding including fine dressing with tongued joining

arragements to support the stone slab with necessary

adhesive as per the design drawing including cost of

arranging the pillar in position with all lead and lift etc

complete.

1 M3

(One

Cubic Meter)

36 6.90 M2

Providing Granite StoneSlab 1nos of dimension

1000mmX750mm mm with necessary stone moulding

including fine dressing with all lead and lift etc complete.

1 M2

(One Square

Meter)

GST 18%

Total

Sub Total


Ground Floor Plan - Cottage

:

Interpr etation Rafter Layout

POOMPUHAR - CRAFT STORE

Restaurant Layout

Poompuhar Shop Layout

Documents

REPAIRING AND RENOVATION OF TOURISM COMPLEX, …