REPAIR IAQ OF RSPOMISSION SUPPORT BUILDING, MS #262

GSK BUILDING, GSK #204UNITED STATES COAST GUARDTRAINING CENTER CAPE MAY

CAPE MAY, NEW JERSEYSHEET INDEX

CONSTRUCTION NOTES

1. GENERAL SCOPE OF WORK CONSISTS OF RELOCATION OF

ESO TESTING AREA FROM MISSION SUPPORT BUILDING #262

TO THE GSK BUILDING, #204 AND WORK RELATED TO THE

FLOOR PLAN CHANGES IN BOTH BUILDINGS, AS WELL AS A

DUCTWORK/ ATTIC VENTILATION REPAIR TO THE GSK

BUILDING AT TRACEN CAPE MAY. REFER TO THE COMPLETE

SET OF CONSTRUCTION DOCUMENTS FOR ALL WORK TO BE

PERFORMED.

2. ALL FEATURES SHOWN ARE EXISTING, UNLESS OTHERWISE

NOTED AS "NEW," "CONSTRUCTION," OR "PROVIDE AND

INSTALL."

3. ALL MATERIALS FOR THE PROJECT SHALL BE FURNISHED BY

CONTRACTOR AND SHALL BE NEW.

4. REFER TO COMPLETE SET OF CONTRACT DOCUMENTS AND

ARCHITECTURAL PLANS FOR ADDITIONAL INFORMATION AND

CONTRACT REQUIREMENTS NOT SHOWN HERE.

5. CONSTRUCTION DETAILS AND SHOP DRAWINGS UTILIZED BY

THE CONTRACTOR SHALL BE REVIEWED AND APPROVED BY

THE CONTRACTING OFFICER'S REPRESENTATIVE (COR) AND

CONTRACTING OFFICER.

6. ANY VARIATION FROM THE CONTRACT DOCUMENTS MUST BE

AUTHORIZED BY THE CONTRACTING OFFICER.

7. ALL WORK SHALL BE PERFORMED IN A WORKMAN LIKE

MANNER IN ACCORDANCE WITH ALL APPLICABLE CODES,

ORDNANCES, AND MANUFACTURER'S RECOMMENDATIONS

AND STANDARDS.

8. THE CONTRACTOR SHALL VERIFY, IN THE FIELD, ALL

CONDITIONS AS SHOWN ON THE PLANS AND SHALL BE

RESPONSIBLE FOR FIELD MEASUREMENTS FOR ALL NEW

CONSTRUCTION OR RETROFITS.

9. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL

SHORRING, UNDERPINNING, AND STRUCTURAL STABILITY

DURING THE WORK.

10. POLLUTANTS SUCH AS FUELS, LUBRICANTS, BITUMENS, RAW

SEWAGE, WASH WATER OR WASTE FROM CONCRETE MIXING

OPERATIONS, AND OTHER HARMFUL MATERIALS SHALL NOT

BE DISCHARGED INTO OR NEAR RIVERS, STREAMS, STORM

SEWER SYSTEMS AND IMPOUNDMENTS, OR INTO NATURAL

OR MAN-MADE CHANNELS LEADING THERETO.

11. ALL APPLICABLE REGULATIONS OF FISH AND WILDLIFE

AGENCIES AND STATUTES RELATING TO THE PREVENTION

AND ABATEMENT OF POLLUTION SHALL BE COMPLIED WITHIN

THE PERFORMANCE CONTRACT.

12. IN THE EVENT CONDITIONS AT THE SITE ARE NOTABLY

DIFFERENT AT THE TIME OF CONSTRUCTION THAN THE

CONSTRUCTION DOCUMENTS PROVIDED, THE CONTRACTOR

SHALL NOTIFY THE COR AND CONTRACTING OFFICER.

LOCATION MAP

SCALE: NTS

MAIN GATE

SITE

TITLE SHEET 1 OF 21

GENERAL SITE PLAN 2 OF 21

ARCH. EXISTING & DEMO PLANS 3 OF 21

ARCH. PROPOSED PLANS FOR MS BUILDING 4 OF 21

ARCH. PROPOSED PLANS FOR GSK BUILDING 5 OF 21

STRUC. M.S. WALL DETAILS 6 OF 21

FIRST FLOOR MS BUILDING MECH. DEMO PLAN 7 OF 21

FIRST FLOOR MS BUILDING NEW WORK PLAN 8 OF 21

MS BLDG. MECHANICAL ROOF PLAN 9 OF 21

MS BLDG. CRAWL SPACE PLBG. DEMO PLAN 10 OF 21

MS BLDG. CRAWL SPACE PLBG. NEW WORK PLAN 11 OF 21

MS BLDG. NEW WORK PLUMBING PLAN AND RISERS 12 OF 21

GSK MECHANICAL DEMO & NEW WORK PLANS 13 OF 21

MECHANICAL SCHEDULES AND DETAILS 14 OF 21

MECHANICAL CONSTRUCTION DETAILS 15 OF 21

PLUMBING SCHEDULES AND DETAILS 16 OF 21

ELECTRICAL DEMOLITION PLAN 17 OF 21

ELEC. NEW WORK PLANS FOR MS 18 OF 21

ELEC. NEW WORK PLANS FOR GSK 19 OF 21

ELEC. POWER TO HVAC EQUIPMENT 20 OF 21

FIRE ALARM PLANS 21 OF 21

SITE

NEWARK

TRENTON

CAMDEN

ATLANTIC CITY

CAPE MAY

NEW

JERSEY

GARDEN STATE PARKWAY

US ROUTE NO. 9

CAPE MAY CANAL

CITY OF CAPE MAY

WASHINGTON ST.

LAFAYETTE ST.

SUPPORT UNIT

GUARD LORAN

U.S. COAST

CAPE MAY HARBOR

OCEAN DRIVE

ATLANTIC OCEAN

TRAINING CENTER

U.S. COAST GUARD

PENNSYLVANIA AVE.

PITTSBURG AVE.

C

A

P

E

M

A

Y

I

N

L

E

T

MTP_SYMBOL

LOCATION PLAN

SCALE: NTS

LOCATION

OF

WORK

GENERAL NOTES:

PROJECT

AREA

SCALE:

MISSION SUPPORT (#262)

FIRST FLOOR PLAN

1/8"=1'-0"

1

A2

SCALE:

GSK LEAN-TO

FLOOR PLAN

1/8"=1'-0"

3

A2

LUCKY BAG

MAIN STORE AREA

(N.I.C.)

LUCKY BAG

STORAGE

(N.I.C.)

OPEN

OFFICE SPACE

MAIL ROOM

OFFICE AREA

(N.I.C.)

STORAGE

(N.I.C.)

PROJECT

AREA

TRANSPORTATION

OFFICE

ID PROCESSING

OFFICE

RSPO

RETIREE

SERVICE

DESK

EDUCATION

CENTER

OFFICE

EDUCATION

CENTER

ESO

LOCATION

OF

WORK

1. DIMENSIONS SHOWN ARE APPROXIMATE. CONTRACTOR SHALL FIELD VERIFY ALL

MEASUREMENTS.

3. FOR ALL STRUCTURAL DEMOLITION & CONSTRUCTION NOTES, REFER TO STRUCTURAL

DRAWINGS.

4. FOR ALL ELECTRICAL AND FIRE ALARM DEMOLITION & CONSTRUCTION NOTES, REFER TO

ELECTRICAL DRAWINGS.

5. FOR ALL MECHANICAL AND PLUMING DEMOLITION & CONSTRUCTION NOTES, REFER TO

MECHANICAL DRAWINGS.

GENERAL DEMOLITION NOTES:

1. REMOVE AND SALVAGE ALL FLOOR CARPET TILES FROM ALL AREAS TO BE RENOVATED, EXCEPT

WHERE NOTED.

2. REMOVE AND SALVAGE ALL HUNG CEILING SYSTEMS EXCEPT WHERE NOTED.

3. DEMOLISH ALL WALL PARTITIONS, INCLUDING FRAMING, WALL BASE, DOORS, AND DOOR

FRAMES, BETWEEN THE ESO TESTING AREA, THE ESO OFFICE, AND THE VETERAN'S OFFICE.

4. DEMOLISH DOOR, INCLUDING FRAME, BETWEEN ESO TESTING AREA AND GENERAL MS

HALLWAY.

5. CUT AND DEMOLISH DOOR OPENING IN CMU WALL, INCLUDING WALL TILING AND BASE,

BETWEEN ESO TESTING AREA AND GENERAL MS HALLWAY.

6. CUT AND DEMOLISH WINDOW OPENING IN CMU WALL, INCLUDING WALL TILING, BETWEEN ESO

TESTING AREA AND GENERAL MS HALLWAY.

7. CUT OPENING ON CONCRETE CEILING AND ROOF SLABS IN M.S. BUILDING NEW HEAD VENTS.

8. REMOVE AND SALVAGE EXTERIOR WINDOW OF GSK OPEN OFFICE SPACE.

9. CUT AND DEMOLISH EXTERIOR DOOR OPENING IN CMU WALL, INCLUDING EXTERIOR PLASTER

AND INTERIOR WALL FURRING AND PANELING, ON GSK OPEN OFFICE SPACE.

GENERAL CONSTRUCTION NOTES:

1. REMOVE AND SALVAGE ALL FLOOR CARPET TILES FROM ALL AREAS TO BE RENOVATED, EXCEPT

WHERE NOTED.

2. BUILD OUT FEMALE HEAD 002 AND MALE HEAD 001 IN THE PREVIOUS ESO TESTING AREA OF THE

MS BUILDING. REFER TO SHEET A-4 FOR ARCHITECTURAL LAYOUT.

3. BUILD OUT GALLERY 003 TO ACCESS NEW HEADS 001 & 002 IN THE PREVIOUS ESO TESTING

AREA OF THE MS BUILDING. FURNISH & INSTALL NEW ENTRYWAY FRAME TO REPLACE

DEMOLISHED DOOR AND FRAME. REFER TO SHEET A-4 FOR ARCHITECTURAL LAYOUT.

4. FURNISH & INSTALL NEW DOOR AND INTERIOR WINDOW, INCLUDING FRAMES, TILE EDGE, AND

SILL IN NEW OPENINGS BETWEEN ESO TESTING AREA AND GENERAL MS HALLWAY. REFER TO

SHEET A-4 & A-5 FOR ARCHITECTURAL LAYOUT.

5. FURNISH & INSTALL NEW EXTERIOR DOOR INCLUDING DOOR FRAME, WALL EDGE INCLUDING

EXTERIOR PLASTER AND INTERIOR WALL FURRING AND PANELING, AND SALVAGED EXTERIOR

WINDOW INCLUDING WINDOW FRAME ON GSK OPEN OFFICE SPACE TO MATCH EXISTING

EXTERIOR. REFER TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

6. CLOSE OUT DEMOLISHED DOOR OPENING INCLUDING EXTERIOR PLASTER AND INTERIOR WALL

FURRING AND PANELING ON GSK OPEN OFFICE SPACE TO MATCH EXISTING EXTERIOR. REFER

TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

7. BUILD OUT WALL PARTITION WITH WALL BASE, DOOR, AND DOOR FRAME IN THE PREVIOUS OPEN

OFFICE SPACE AREA OF THE GSK BUILDING TO DEFINE THE NEW OPEN OFFICE SPACE 005.

REFER TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

8. BUILD OUT WALL PARTITION WITH WALL BASE, DOOR, AND DOOR FRAME IN THE PREVIOUS OPEN

OFFICE SPACE AREA OF THE GSK BUILDING TO DEFINE THE NEW ESO TESTING AREA 007. REFER

TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

9. BUILD OUT WALL PARTITION WITH WALL BASE, DOOR, DOOR FRAME AND INTERIOR WINDOW IN

NEW ESO TESTING AREA 007 TO DEFINE THE ESO OFFICE SPACE 008 IN THE GSK BUILDING.

REFER TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

10. RECONFIGURE SALVAGED HUNG CEILING SYSTEM TO MATCH NEW LAYOUT IN THE GSK

BUILDING. REFER TO SHEET A-5 FOR ARCHITECTURAL LAYOUT.

SCALE:

MISSION SUPPORT (#262)

SECOND FLOOR PLAN

1/8"=1'-0"

2

A2

PROJECT

AREA

PURCHASING

STORAGE

SPO

COMPTROLLER

PROJECT

AREA

1

A3

SCALE:

EXISTING MS ESO SPACE

FIRST FLOOR PLAN

1/4"=1'-0"

2

SCALE:

DEMO MS SPACE

FIRST FLOOR PLAN

1/4"=1'-0"

4

A3SCALE:

EXISTING GSK OFFICE

FLOOR PLAN

1/4"=1'-0"

5

A3SCALE:

DEMO GSK OFFICE

FLOOR PLAN

1/4"=1'-0"

22'-11"

7'-8

1

2

"1

1'-1

0

1

2

"

ESO

TESTING AREA

458 SF

ESO

OFFICE

120 SF

VETERANS

OFFICE

76 SF

20

'-1

"

10'-2"

TELECOMM

CLOSET

30 SF

OPEN

OFFICE SPACE

702 SF

HEAD

44 SF

20

'-1

"

10'-2"

7

1

2

"

11'-4"3'-4"3'-10"

19

'-6

1

2

"

9'-5"

6'-11

1

2

"21'-3

1

2

"

7'

38'-6"

1'-3"

5'-1"

5'-0

1

2

"

33'-5"

3'-4"

F C

A

A

A

B

B

D E

B

GENERAL DEMOLITION NOTES:

1. DEMOLISH NOTED WALL PARTITIONS,

INCLUDING WALL STUDS, AND WALL

BASES.

2. REMOVE AND SALVAGE ALL FLOOR

CARPET, CARPET TILES, AND VINYL TILES,

EXCEPT WHERE NOTED. STRIP ALL

REMAINING ADHESIVE FROM FLOOR.

3. REMOVE AND SALVAGE ALL ACOUSTIC

HUNG CEILING SYSTEM, INCLUDING HVAC

RETURNS, EXCEPT WHERE NOTED.

LEGEND

CARPET TILES & SUSPENDED

CEILING TILE TO BE

REMOVE AND SALVAGE.

PARTITIONS & WALLS

TO BE DEMOLISHED.

SPECIFIC DEMOLITION NOTES:

A. DEMOLISH WALL PARTITION, INCLUDING

PANELING, STUDS, & WALL BASE WHERE

REQUIRED.

B. DEMOLISH DOOR & DOOR FRAME WHERE

REQUIRED..

C. CUT CMU WALL FOR NEW DOOR WHERE

REQUIRED.

D. OPENING. DEMO INCLUDES PANELING,

FURING, WALL BASE AND WALL TILES

WHERE REQUIRED.

E. CUT CMU WALL ALONG EXISTING MORTAR

JOINT FOR NEW DOOR OPENING. DEMO

INCLUDES PANELING, FURING, WALL BASE

AND WALL TILES WHERE REQUIRED.

F. DEMOLISH CMU WALL ALONG EXISTING

MORTAR JOINT FOR NEW WINDOW

OPENING. DEMO INCLUDES PANELING,

FURING, WALL BASE AND WALL TILES

WHERE REQUIRED.

G. REMOVE & SALVAGE DOUBLE WINDOW TO

REINSTALL AS SINGLE WINDOW.

B

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

3

A3

SCALE:

DEMO MS SPACE

SECOND FLOOR PLAN

1/4"=1'-0"

4" FLOOR SLAB

PENETRATION

FOR VENT,

CENTERED

ON WALL

EQ

.E

Q.

PURCHASING

STORAGE

AREA

A

4'-1

0"

A3

A

A3

SCALE:

DEMO GSK OFFICE

WALL SECTION

1/4"=1'-0"

6'-8

1

2

"

A

A2

A

A3

SCALE:

DEMO GSK OFFICE

WALL SECTION

1/4"=1'-0"

6'-8

1

2

"

A

A2

4'-10"

LOUVER TO

BE REMOVED

SEE MECH. DWG

OUTLET TO

BE REMOVED

SEE ELEC. DWG

MD1

MD1

MD1

1

A4SCALE:

PROPOSED MS ESO SPACE

FIRST FLOOR PLAN

1/4"=1'-0"

4'-4"

7'

12

'-2

"

20

'-1

"

4'-8"

MALE

HEAD

132 SF

FEMALE

HEAD

60 SF

GALLERY

32 SF

RECRUIT

WAITING

AREA

395 SF

11"

3'-10" 3'-4"

1'-4"

10'

6"

3'-4"

8"

12

'-7

1

2

"

7'-5

"

4'-9"

1'-6

"2

'-3

"2

'-3

"1

'-1

0"

1'-3

"2

'-6

"2

'-6

"3

'

2'-6

"2

'-6

"2

'-6

"4

'-8

"

5

1

2

"

4'-8

"

1'-6"

1'-9

"3

'-6

"

11" 4'-8" 4'-7"

1'-9

"

4'

1'-2

"1

'-1

0"

11

"

02

01

03

04

A

-

5

7

4

6

5

-

4

001

002

003

004

2

A4

SCALE:

PROPOSED MS ESO SPACE

FIRST FLOOR CEILING PLAN

1/4"=1'-0"

A

UR

UR

UR

LAV

LAV

LAV

LAV

WC

WC

WC

3'-4"

7

1

2

"

LAV

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

HVAC UNIT

TO REMAIN

A

A2

6

-

- -

7

A4

3

A3SCALE:

MS SECOND FLOOR

VENT DETAILS

1/4"=1'-0"

1

2

" INTERIOR GRADE

GYPSUM BOARD

OVER 3

5

8

" METAL STUDS

AROUND VENT STACK

10"

1'-4

"

EXISTING CLOSED-OUT

SERVICE WINDOWS

EXISTING CLOSED-OUT

SERVICE WINDOWS

7'-1

1"

8'-2

"

1

2

" INTERIOR GRADE

GYPSUM BOARD

OVER 3

5

8

" METAL STUDS

7'-9

"

11

"3

'-1

0"

3'

1

1

2

"

2"

SCALE:

SECTION A

1/2"=1'-0"

A4

FIXED ¼” GLASS

WINDOW WITH

2” ALUMINUM

FRAME

2"

WOOD SILL

A

6'-1

0"

PRE-CAST

REINFORCED

CONCRETE LINTEL,

SEE STRUC DWG

6'-1

0"

SCALE:

INTERIOR

ELEVATION

3/8"=1'-0"

8

A4

A A

3'-6

"

3'

2"

2"

3'-1

0"

1

1

2

"

10'

10'

2" 2"

3'-4"5" 5"1'-4"

A

A4

8"

PRE-CAST REINFORCED

CONCRETE LINTEL,

SEE STRUC DWG

TILE EDGE TO

MATCH EXISTING

EXISTING

HUNG CEILING

SYSTEM

03

04

WALL TILE CUT

TO FIT WINDOW

OPENING

7'-9

"

SCALE:

INTERIOR ELEVATION

1/4"=1'-0"

6

A A

04

03

7'-9

"

3'-1

0"

3'

6'-1

0"

6'-1

0"

6'-1

0"

2'-1

0"

4'-1

0"

1'

1'-5

"

05

02

06

A4

7'-9

"

SCALE:

INTERIOR ELEVATION

1/4"=1'-0"

7

6'

6'-1

0"

1'-9

"

2'-1

0"

6'-1

0"

3'-6

"

1'

4'-1

0"

2'

1'

02

01

06

UR

A4

7'-9

"

SCALE:

INTERIOR ELEVATION

1/4"=1'-0"

4

02

7'-9

"

4"

6'

6'-1

1"

2'-1

0"

3'-4

"2

'-6

"

2'-1

0"

3'-4

"2

'-6

"

06 06 06 07 07

LAV LAV LAV

03 03 04 04

LAV

A4SCALE:

INTERIOR ELEVATION

1/4"=1'-0"

5

6'-1

0"

4'-1

0"

1'

2'

3'-6

"1

'

4'-1

0"

1'

6'-1

0"

7'-9

"

UR UR UR

02

01 0104

0202

A4

01

02

DESCRIPTIONNAMENUM.

URINAL SCREEN

PARTITION

SCREEN

PHENOLIC PARTITION BOARD,

FLOOR & WALL BRACED

PHENOLIC PARTITION BOARD,

WALL BRACED, 18" x 42"

03SOAP

DISPENSER

WALL MOUNTED @ 44" HEIGHT

04PAPER

DISPENSER

WALL MOUNTED @ 52" HEIGHT

05TOILET PAPER

ROLL HOLDER

WALL MOUNTED, DOUBLE ROLL, @ 24"

HEIGHT

SCHEDULE

BATHROOM ACCESSORIES

06MIRROR WALL MOUNTED, 18" X 30", @ 40"

HEIGHT

LAV

DESCRIPTIONNAMETAG

CABINET

MOUNTED

LAVATORY

16" X 13" OVAL WHITE VITREOUS

CHINA, WALL MOUNTED LAVATORY.

SCHEDULE

BATHROOM FIXTURE

URURINAL WHITE VITREOUS CHINA WALL

MOUNTED, LOW CONSUMPTION

SIPHON JET FLUSH ACTION.

WCWATER CLOSET WHITE VITREOUS CHINA WALL

MOUNTED, LOW CONSUMPTION

SIPHON JET FLUSH ACTION.

EXISTING PRECAST

CONCRETE

"DOUBLE T" BEAM

BATHROOM

VENT STACK

4" FLOOR SLAB

PENETRATION

EXISTING

FINISHED

FLOOR LEVEL

EXISTING

HUNG CEILING

LEGEND

2' x 2' COMMERCIAL GRADE

CARPET TILES W/ ADHESIVE

6" X 6" GLAZED TILES

GENERAL NOTES:

1. DIMENSIONS SHOWN ARE APPROXIMATE. CONTRACTOR

SHALL FIELD VERIFY ALL MEASUREMENTS.

3" X 6" GLAZED

WALL TILES

SUBWAY PATTERN

NEW WALL

SECTIONS

1

2

" INTERIOR GRADE

GYPSUM BOARD OVER

3

5

8

" METAL STUDS,

16" O.C. W/ SOUND BATTING

1

2

" INTERIOR GRADE

GYPSUM BOARD OVER

2" X 4" WOOD STUDS,

16" O.C. W/ SOUND BATTING

2' X 4' RECESSED,

LED LIGHT FIXTURE

SUSPENDED CEILING

SYSTEM W/ 2' X 2'

ACOUSTIC TILES

EXISTING

FINISHED

FLOOR LEVEL

FLOOR PLAN:

CEILING PLAN:

INTERIOR ELEVATION:

2' X 2' RECESSED,

LED LIGHT FIXTURE

OPAQUE WINDOW FILM

INSTALLED ON EXISTING

WINDOWS

OPAQUE WINDOW FILM INSTALLED

ON EXISTING WINDOWS

OPAQUE WINDOW FILM INSTALLED

ON EXISTING WINDOWS

15'-6"

PRE-CAST REINFORCED

CONCRETE LINTEL,

SEE STRUC DWG

CEILING PLAN NOTE:

1. SEE MECH. & ELEC. SHEETS FOR DETAILS.

01

DO

OR

NU

M.

DOOR SCHEDULE:

DOOR SIZE

WIDTH HEIGHT

OPENING SIZE

WIDTH HEIGHT

DOOR

MATERIAL

FRAME

MATERIAL

COMMENTS

3'-0" 6'-8"3'-4" 6'-10" METALWOOD

02

03

04

05

06

07

FIXED LOUVER, W/ KICK PLATE

08

3'-0" 6'-8"3'-4" 6'-10" METALWOOD FIXED LOUVER, W/ KICK PLATE

3'-0" 6'-8"3'-4" 6'-10" METALN/A OPEN FRAME, NO DOOR

3'-0" 6'-8"3'-4" 6'-10" METALWOOD

1

4

" GLASS VISION PANEL, FRAME TO MATCH EXISTING DOORS

2'-10" 6'-8"3'-10" 6'-10" METALMETAL

1

4

" GLASS VISION PANEL, W/ BOTTOM DOOR SEAL

3'-0" 6'-10"3'-4" 7'-0" METALMETAL

1

4

" GLASS VISION PANEL, FIXED LOUVER, W/ KICK PLATE

3'-0" 6'-10"3'-4" 7'-0" METALMETAL

1

4

" GLASS VISION PANEL, FIXED LOUVER, W/ KICK PLATE

2'-4" 6'-10"2'-8" 7'-0" METALMETAL

1

4

" GLASS VISION PANEL, FIXED LOUVER, W/ KICK PLATE

2"

2"

7'-1

0"

10

"4

'3

'

SCALE:

SECTION B

1/2"=1'-0"A5

FIXED ¼” GLASS

WINDOW WITH

2” ALUMINUM

FRAME

B

HUNG CEILING

SYSTEM

1

2

" INTERIOR GRADE

GYPSUM BOARD OVER

2" X 4" WOOD STUDS,

16" O.C. W/ SOUND BATTING

1

2

" INTERIOR GRADE

GYPSUM BOARD OVER

2" X 4" WOOD STUDS,

16" O.C. W/ SOUND BATTING

6"

B

A5

B

4'

7'

3'

4'

2"

SCALE:

INTERIOR

ALUM. WINDOW B

3/8"=1'-0"

3

A5

2"

2"

2"

2'-8"

1

A5

SCALE:

PROPOSED ESO TESTING OFFICE

FLOOR PLAN

1/4"=1'-0"

2

A5

SCALE:

PROPOSED ESO TESTING OFFICE

CEILING PLAN

1/4"=1'-0"

OPEN

OFFICE SPACE

217 SF

ESO

TESTING

AREA

702 SF

ESO

OFFICE SPACE

702 SF

GALLERY

170 SF

EXISTING

TELECOMM

CLOSET

30 SF

6'

13

'-1

0"

5'-3

1

2

"

8'-1

1

2

"

3'-4

"2

'-9

"

11

1

2

"

8'-1

"3

'-4

"3

'-6

"

1'-4

1

2

"

9'-10"

13

'-1

1

2

"

17'-9"

4'-3"

15'-8"

1'-8"2'-8"7" 3'-11" 1'

08

07

06

05

B

5"

005

006

008

007

3'-5

1

2

"3'-9

1

2

"

5"

3'-10"

5"

B

A5

3

A5

4'-10"

5'

WOOD PLATFORM

TO MATCH EXISTING

6'-8

"

3'

04

DOOR TYPE

3'

05

DOOR TYPE

6'-8

"

2'-10"

06

DOOR TYPE

6"

3'

07

08

DOOR TYPE

6'-1

0"

SCALE:

DOOR TYPE

ELEVATIONS

3/8"=1'-0"

6" 6"

6"

2'-8

"

6"

6'-1

0"

2'-1

0"

9"

KEYED

LOCK &

HANDLE

TO BE

INSTALLED

KEYED

LOCK &

HANDLE

TO BE

INSTALLED

KEYED

LOCK &

HANDLE

TO BE

INSTALLED

METAL

KICK

PLATE

2'-4"

6" 1'-4"

6"

2'-1

0"

11

"1

'-1

0"

6"1'-4"

FIXED

LOUVERS

1

4

" GLASS

VISION

PANEL

1

4

" GLASS

VISION

PANEL

1

4

" GLASS

VISION

PANEL

01

DOOR TYPE

METAL

KICK

PLATE

11

"1

'-1

0"

6"2'

FIXED

LOUVERS

11

"1

'-1

0"

6"2'

METAL

KICK

PLATE

FIXED

LOUVERS

BOTTOM

DOOR SEAL

6'-8

"

6"

10

1

2

"1

0

1

2

"1

0

1

2

"

2'-8

1

2

"

6" 2'

1

4

" GLASS

VISION

PANEL

METAL

KICK

PLATE

7'

6'-1

0"

6'-9

1

2

"

DOOR FRAME

06 07 08

6'-1

0"

6'-8

"

6'-7

1

2

"

DOOR FRAME

6'-1

0"

6'-8

"

03DOOR FRAME

01 02 04

SCALE:

DOOR FRAME

ELEVATIONS

3/8"=1'-0"

6'-9

1

4

"

6'-8

"

6'-7

1

4

"

7'-1

3

4

"

6'-9

"

6'-8

"

6'-7

1

4

"

7'-2

1

2

"

4

1

2

"

5

1

2

"

05DOOR FRAME

INTERIOR

05DOOR FRAME

EXTERIOR

WOOD FRAMING

TO MATCH EXISTING

WOOD FRAMING

TO MATCH EXISTING

GENERAL NOTE:

1. DIMENSIONS SHOWN ARE APPROXIMATE. CONTRACTOR SHALL FIELD VERIFY ALL MEASUREMENTS.

001

RO

OM

NU

M.

ROOM NAME FLOOR BASE WALLS CEILING COMMENTSHEIGHT

CEILING

FINISHES SCHEDULE:

2 2 1,3,4 1 7'-9"

AREA

132 S.F.MALE HEAD

002 1 7'-9"60 S.F.FEMALE HEAD-

003 132 S.F.GALLERY

004 1395 S.F.

RECRUIT WAITING

AREA

005 1 1 2 1 7'-10"69 S.F.OPEN OFFICE SPACE

006 1 1 1,2 1 7'-10"44 S.F.GALLERY

007 1 1 2 1 7'-10"760 S.F.ESO TESTING AREA

008 1 1 1, 2 1 7'-10"760 S.F.ESO OFFICE SPACE

7'-9"

7'-9"

2 2 3,4

1 1 1,3

1 1 1,3

-

-

-

-

-

-

-

1. 2' x 2' COMMERCIAL GRADE CARPET TILES W/ ADHESIVE

2. 6" X 6" GLAZED TILES

FLOOR

1.

1

8

" RESILIENT VINYL BASE, 4" H, W/ ADHESIVE

2. 3" GLAZED TILE BASE

BASE

1. CMU WALL, PRIMED & 2 COAT PAINTED W/ LATEX

2.

1

2

" INTERIOR GRADE GYPSUM BOARD OVER 2" X 4"

WOOD STUDS,16" O.C., W/ SOUND BATTING;

PLASTERED, PRIMED, & 2 COAT LATEX PAINTED.

3.

1

2

" INTERIOR GRADE GYPSUM BOARD OVER 3

5

8

" METAL

STUDS,16" O.C., W/ SOUND BATTING; PLASTERED,

PRIMED, & 2 COAT LATEX PAINTED.

4. 3" X 6" GLAZED TILE; 6' HEIGHT; SUBWAY TILE LAYOUT.

WALLS

1. SUSPENDED ACOUSTIC CEILING TILE SYSTEM W/ 2' X 2'

ACOUSTIC TILES ON 1

1

2

" CARRIER CHANNELS & 1" X 5"

WOOD CEILING FRAME.

CEILING

02

VINYL BASE

TO MATCH EXISTING

08

VINYL BASE

TO MATCH

EXISTING

HUNG CEILING

SYSTEM

2'-2"

A

A5

6'-8

"

REPAIR

FLUSHED

CEILING

NEW

PARTITION

WALL REPAIR

A

A5SCALE:

SECTION A

3/8"=1'-0"

CEILING PLAN NOTE:

1. SEE MECH. & ELEC. SHEETS FOR DETAILS.

MASONRY NOTES:

1. CONCRETE MASONRY UNITS (CMU) SHALL CONFORM TO ASTM C90 AND MEET THE

FOLLOWING COMPRESSIVE STRENGTH (f'm) REQUIREMENTS:

1.1. HOLLOW CONCRETE MASONRY UNITS: 1,700 PSI.

1.2. SOLID CONCRETE MASONRY UNITS:2,500 PSI.

2. ALL WORK SHALL BE IN ACCORDANCE TO THE REQUIREMENTS OF ACI 53 AND ACI

530.1.

3. MORTAR SHALL BE TYPE N AND CONFORM TO ASTM C 270. TYPE N, COMPRESSIVE

STRENGTH OF 750 PSI.

4. GROUT SHALL CONFORM TO ASTM C476.

5. NON-SHRINK GROUT SHALL CONFORM TO ASTM C1107. COMPRESSIVE STRENGTH OF

7,000 PSI AT 28 DAYS.

6. REINFORCING BARS SHALL BE DEFORMED AND CONFORM TO ASTM A 615, GRADE 60.

7. LAP SPLICES FOR DEFORMED REINFORCING BARS SHALL BE A MINIMUM OF 24 BAR

DIAMETERS OR 12", WHICHEVER IS GREATER.

8. ALL JOINTS SHALL BE CONCAVE.

REINFORCED CONCRETE NOTES:

1. CONCRETE SHALL HAVE A MINIMUM COMPRESSIVE STRENGTH OF 5,000 PSI AT 28

DAYS.

2. ALL CONCRETE WORK SHALL BE IN ACCORDANCE WITH REQUIREMENTS OF ACI 318,

LATEST EDITION.

3. REINFORCING BARS SHALL BE DEFORMED AND CONFORM TO ASTM A615, GRADE 60.

4. LAP SPLICES SHALL BE A MINIMUM OF 42 BAR DIAMETERS.

5. REINFORCING SHOWN IS THE MINIMUM REQUIRED. ADDITIONAL REINFORCING

NECESSARY FOR HANDLING SHALL BE THE OPTION AND RESPONSIBILITY OF THE

CONTRACTOR.

NOTES:

1. ALL MATERIALS FOR THE PROJECT SHALL BE FURNISHED BY THE CONTRACTOR AND

SHALL BE NEW.

2. REFER TO COMPLETE SET OF CONTRACT DOCUMENTS AND ARCHITECTURAL PLANS

FOR ADDITIONAL INFORMATION AND CONTRACT REQUIREMENTS NOT SHOWN HERE.

3. CONSTRUCTION DETAILS AND SHOP DRAWINGS UTILIZED BY THE CONTRACTOR

SHALL BE REVIEWED AND APPROVED BY THE CONTRACTING OFFICER

REPRESENTATIVE (COR).

4. ANY VARIATION FROM THE CONTRACT DOCUMENTS MUST BE AUTHORIZED BY THE

CONTRACTING OFFICER (KO).

5. ALL WORK SHALL BE PERFORMED IN A WORKMAN LIKE MANNER IN ACCORDANCE

WITH ALL APPLICABLE CODES, ORDINANCES AND MANUFACTURER'S

RECOMMENDATIONS AND STANDARDS.

6. THE CONTRACTOR SHALL VERIFY, IN THE FIELD, ALL CONDITIONS AS SHOWN ON THE

PLANS AND SHALL BE RESPONSIBLE FOR FIELD MEASUREMENTS FOR ALL NEW

CONSTRUCTION OR RETROFITS.

7. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL SHORING, UNDERPINNING ANS

STRUCTURAL STABILITY DURING THE WORK.

8. IN THE EVENT CONDITIONS AT THE SITE ARE NOTABLY DIFFERENT AT TIME OF

CONSTRUCTION THAN THE CONSTRUCTION DOCUMENTS PROVIDED, THE

CONTRACTOR SHALL NOTIFY THE COR.

1

S1

SCALE:

PROPOSED MS

WALL ELEVATION

1/2"=1'-0"

A

S1

EXISTING FINISHED

FLOOR LEVEL

EXISTING

HUNG CEILING

EXISTING

DOORWAY

CUT WALL ALONG

EXISTING MORTAR

JOINTS (TYP.)

NEW

DOORWAY

& FRAME

EXISTING TILE

LINE

6" X 16" X 8" CMU,

SEE DETAIL 2/S1

PRECAST

CONCRETE

LINTEL

PRECAST

CONCRETE

LINTEL

NEW

WINDOW FRAME

CUT WALL ALONG

EXISTING MORTAR

JOINTS (TYP.)

EXISTING TILE

LINE

6" X 16" X 8"

CMU (TYP.)

NEW

WINDOW

& FRAME

NEW

DOORWAY

& FRAME

NEW

CONCRETE LINTEL

NEW

CONCRETE LINTEL

6" X 16" X 8"

CMU (TYP.)#4 REBAR

7,000 PSI

NON-SHRINK

GROUT IN CMU

BLOCK CAVITIES,

SEE SECTION B/S1

PORTION

OF EXISTING

CMU WALL

TO REMAIN

2

S1

SCALE:

PROPOSED MS

WALL REINFORCING DETAIL

3/4"=1'-0"

A

S1

SCALE:

TYPICAL LINTEL SECTION A

1 1/2"=1'-0"

6" X 16" X 8"

CMU (TYP.)

6" X 16" X 4"

CMU CAP (TYP.)

#4 REBAR (TYP).

1

1

2

" CLEAR EACH WAY

5,000 PSI

CONCRETE

WINDOW FRAME

7

5

8

"

EXISTING PRECAST

CONCRETE "DBL T" BEAM

B

S1

B

S1

SCALE:

TYPICAL COLUMN SECTION B

3"=1'-0"

DOOR

FRAME

3

8

"-16 X 4" FH MACHINE SCREW WITH

CONCRETE EXPANSION SHIELD AT 24"

O.C. FOUR ANCHORS PER SIDE

7,000 PSI

NON-SHRINK GROUT

#4 REBAR

WINDOW

FRAME

WINDOW FRAME ANCHORS PURSUANT

TO MANUFACTURER'S REQUIREMENTS

CAULK JOINT BETWEEN

DOOR/WINDOW FRAMES

AND CMU (TYP. BOTH SIDES)

EXISTING PRECAST

CONCRETE BEAM

EXISTING PRECAST CONCRETE

"DOUBLE T" BEAM

SCALE:

MS BUILDING

FIRST FLOOR DEMO PLAN

1/8"=1'-0"

M1

ITEM SPECIFIC NOTES:

1. DEMOLISH EXISTING SIDEWALL MOUNTED EXHAUST FAN AND

PREPARE OPENING (ENLARGE) FOR NEW LOUVER INSTALLATION.SEE

ELECTRICAL DRAWINGS FOR ELECTRICAL REQUIREMENTS.

2. DEMOLISH EXISTING PRE-CAST CONCRETE PLANK (SIDING) IN THE

AMOUNT NEEDED TO INSTALL NEW LOUVER ABOVE EXISTING AND

PROPOSED CEILING. COORDINATE LOCATION WITH EXISTING

CONDITIONS AND PROPOSED DUCTWORK LAYOUT.

3. PARTIALLY DEMOLISH EXISTING HCS/HCR SUPPLY AND RETURN

PIPING IN AMOUNT NEEDED IN ORDER TO CONNECT NEW PIPING /

EQUIPMENT AND FITTINGS.

4. EXISTING FCU IS TO BE DEMOLISHED AND DISPOSED, ALL

CONNECTION PIPES CAPPED, WALL AND FLOOR REPAIRED FOR NEW

FINISH. SEE ELECTRICAL & NEW ARCITECTURAL WORK DRAWINGS FOR

MORE INFO.

5. EXISTING FCU IS TO BE DEMOLISHED AND DISPOSED,, ALL

EXISTING PIPING REMOVED FOR FLOOR INSTALLATION AND THEN

REINSTALLED INTO THE SAME LOCATION UPON NEW FLOORING

INSTALLATION. TEMPORARY CAP PIPING AND REINSTALL. SEE

ELECTRICAL & NEW WORK DRAWINGS FOR MORE INFO.

6. DEMOLISH EXISTING CEILINGS REGISTERS AND RELATED

DUCTWORK IN ORDER TO ACCOMMODATE NE DUCTWORK.

7. EXISTING CONDENSATE PUMP AND DISCHARGE THAT IS ROUTED

THROUGH THE CEILING IS TO BE DEMOLISHED. CONTRACTOR TO

REOPEN EXISTING FLOOR DRAIN CONDENSATE AND PREPARE FOR

FUTURE CONNECTION/UNIT REINSTALLATION. SEE NEW WORK

DRAWINGS FOR MORE INFO.

POINT OF CONNECTION

POINT IF DEMOLITION

POINT IF DEMOLITION (CAP)

FLOOR DRAIN

CLEANOUT

TO BE DEMOLISHED

EQUIPMENT TAG WITH

BALANCING INFO

VENT PIPING

UNDERGROUND SANITARY PIPE

SANITARY PIPE

HEATING / COOLING SUPPLY

HEATING / COOLING RETURN

CONDENSATE PIPE

"E-*" EXISTING PIPE OF "*" TYPE

VENT THROUGH ROOF WITH PIPE SIZE

MOTORIZED DAMPER

BACKDRAFT (GRAVITY) DAMPER

VOLUME DAMPER

THERMOSTAT

REMOTE SENSOR WITH STATUS DISPLAY

ACCESS PANEL

BREAK IN DUCTWORK / PIPING

VERTICAL FAN COIL UNIT

C

LEGEND

DEMOLITION WORK NOTES*:

#

M

U-SAN

HCS

HCR

COND

E-*

T

AP

GENERAL EXISTING INSTALLATION AND

DEMOLITION NOTES *:

A. COORDINATE ALL CONTRACT ACTIVITIES, DEMOLITION AND NEW

INSTALLATION WORK WITH COR, MS BUILDING AND GSK BUILDINGS

MANAGEMENT. ALL MAJOR DEMOLITION AND NEW WORK WITHIN

OFFICE AREAS IS TO BE PERFORMED SIMULTANEOUSLY IN ORDER

TO MINIMIZE DOWN TIME AND POSSIBLE RELOCATIONS OF

OCCUPANTS.

B. CONTRACTOR IS TO PERFORM ALL WORK IN WORKMAN LIKE

MANNER WITH PROPER CARE TO THE MS BUILDING AND GSK

BUILDINGS PROPERTY. ALL DAMAGE CAUSED TO THE

GOVERNMENT'S PROPERTY DURING THE CONSTRUCTION IS TO BE

RECTIFIED BY CONTRACTOR. ALL SURFACES AND GROUNDS

AFFECTED BY THE CONSTRUCTION ARE TO BE LEFT AT

PRE-CONSTRUCTION CONDITION UPON THE PROJECT COMPLETION.

C. EXISTING GSK AIR HANDLING UNITS WHOSE DUCTWORK IS TO BE

MODIFIED AND REBALANCED ARE LOCATED UNDER A SLOPED ROOF

CLOSE TO CEILING. (AT 8 FT. ABOVE FINISHED FLOOR (AFF)),

FLOORING IS CARPET AND VINYL TILE.

D. EXISTING MS BUILDING HVAC CONSISTS MOSTLY OF VERTICAL FAN

COIL UNITS WITH 2-PIPE CHANGEOVER WHICH LOUVERS ARE

MOSTLY BLOCKED/CAPPED AND EXHAUST FANS SERVING

BATHROOMS. BUILDING IS SERVED WITH NEAR BUILDING LOCATED

CHILLER FOR COOLING OPERATION. ADJACENT BOILER ROOM

(WITHIN 30 FT. FROM BUILDING EDGE) HOUSES BUILDING

MANAGEMENT PANEL BY " SIEMENS" AND TWO BOILERS FOR

HEATING OPERATION.

E. CONTRACTOR IS TO COORDINATE DEMOLITION OF FANS/LOUVERS

AND NEW LOUVER SELECTION AND INSTALLATION INTO EXISTING

RECONNECTION OF EXISTING REFRIGERATION LINES AND

DUCTWORK TO THE NEW UNITS.

F. ALL UNOPERATIONAL SIDEWALL FANS AND LOUVERS SHOWN TO BE

ABBANDONED ARE TO BE DISCONNECTED FROM ELECTRIC GRID ,

CAPPED FROM INSIDE AND LEFT IN PLACE.

G. FOR ALL ELECTRICAL POWER AND FIRE ALARM DEMOLITION

REQUIREMENTS, REFER TO ELECTRICAL DRAWINGS.

H. BOTH FIRST AND SECOND FLOOR HAVE A 6'-6" WIDE SILL FOR EASY

ACCESS (VIA LADDER) TO EXISTING FANS AND LOUVERS.

SAN

1

GENERAL EXISTING INSTALLATION AND

DEMOLITION NOTES *:

A. IF NOT NOTED DIFFERENTLY, ALL EXISTING CEILINGS ARE

ACOUSTICAL CEILING TILE (ACT). CEILING GRIDS THAT ARE

IMPACTED BY CONSTRUCTION ARE TO BE TAKEN DOWN AND

REINSTALLED/ MODIFIED TO SUIT INSTALLATION.

B. CONTRACTOR IS TO PERFORM THE WORK IN WORKMAN LIKE

MANNER WITH PROPER CARE TO THE MS BUILDING AND GSK

BUILDINGS PROPERTY. ALL DAMAGE CAUSED TO THE

GOVERNMENT'S PROPERTY DURING THE CONSTRUCTION IS TO

BE RECTIFIED BY CONTRACTOR. ALL SURFACES AND GROUNDS

AFFECTED BY THE CONSTRUCTION ARE TO BE LEFT AT

PRE-CONSTRUCTION CONDITION UPON THE PROJECT

COMPLETION.

C. EXISTING MS BUILDING HVAC CONSISTS MOSTLY OF VERTICAL

FAN COIL UNITS WITH 2-PIPE CHANGEOVER WHICH LOUVERS

ARE MOSTLY BLOCKED/CAPPED AND EXHAUST FANS SERVING

BATHROOMS. BUILDING IS SERVED WITH NEAR BUILDING

LOCATED CHILLER FOR COOLING OPERATION. ADJACENT

BOILER ROOM (WITHIN 30 FT. FROM BUILDING EDGE) HOUSES

BUILDING MANAGEMENT PANEL BY " SIEMENS" AND TWO

BOILERS FOR HEATING OPERATION.

D. CONTRACTOR IS TO COORDINATE DEMOLITION OF

FANS/LOUVERS AND NEW LOUVER SELECTION AND

INSTALLATION INTO EXISTING CONCRETE IN REGARDS TO CORE

DRILLING AND REQUIRED SIZING.

E. FOR ALL ELECTRICAL POWER AND FIRE ALARM DEMOLITION

REQUIREMENTS, REFER TO ELECTRICAL DRAWINGS.

CONCRETE

BEAM (TYP.)

(10" CLEARANCE)

EXG. HCS & HCR

IN FIRST FL. CEILING

1

2

3

1

1

2

" VENT UP TO

SEC. FLOOR

EXG. COND. LINE

IN CEILING

(SERVING 2ND FL.)

FCU

1

2

D3

VENT

3

4

5

4

CD

5

RM

5

5

5

D1

D1

#

"*"- APPLICABLE TO ALL DEMOLITION DRAWINGS

D2

D2

D2

D2

6

6

6

7

7

B

S

SCALE:

MS BUILDING

FIRST FLOOR NEW WORK PLAN

1/8"=1'-0"

1

M2

CONNECT TO EXG.

GENERAL NEW WORK NOTES:

A. AT LOCATIONS WHERE EXISTING HCS&R (2-PIPE HEAT-COOL SUPPLY AND RETURN) PIPING IS RECEIVING NEW PIPING CONNECTIONS EXISTING AND NEW PIPING

,FITTINGS AND VALVES ARE TO BE INSULATED.

B . INSTALL VERTICAL FAN COIL UNITS UPON NEW FLOORING AND WALL PAINTING IS DONE. RECONNECT AND INSULATE EXISTING AND NEW 2-PIPE CONNECTIONS

AND CONDENSATE LINES AND RECONNECT INTO EXISTING CRAWL SPACE CONDENSATE PIPING TO COMPLETE INSTALLATION.

C. INSULATE CONDENSATE PIPES AND TRAPS FROM FAN COIL UNITS.

D. INSTALL / PROVIDE LOUVER WITH NEW DOORS THAT ARE SHOWN TO RECEIVE LOUVERS.

E. COORDINATE INSTALLATION OF NEW DIFFUSERS AND FAN COIL UNIT INTO NEW CEILING GRID. PROVIDE ADEQUATE ACCESS FOR FAN COIL UNIT FILTER

REMOVAL AND MAINTENANCE.

F. COORDINATE INSTALLATION OF CEILING MOUNTED IN LINE FANS WITH EXISTING CEILING CONDITIONS AND 30" WIDE PRE-CAST CONCRETE BEAMS SEPARATING

FLOORS.

G. MOUNT NEW CONDENSATE PUMPS AT NEARBY EXISTING/NEW WALL AND COORDINATE DISCHARGE WITH LAVATORY TAILPIECE PIPING.

H. COORDINATE LOUVER SELECTION AND INSTALLATION WITH EXISTING WALL & CEILING CONDITIONS AND PRE-CAST PLANKS AND CONCRETE T-. JOISTS. CAULK

ALL GAPS TO COMPLETE INSTALLATION.

ITEM SPECIFIC NOTES:

1. PROVIDE A NEW ROUND LOUVER AND INSTALL IT INTO EXISTING

CONCRETE PLANK SIDEWALL .SEE ELECTRICAL DRAWINGS FOR

ELECTRICAL REQUIREMENTS.

2. DEMOLISH EXISTING PRE-CAST CONCRETE PLANK (SIDING) IN THE

AMOUNT NEEDED TO INSTALL NEW LOUVER ABOVE EXISTING WINDOW

AND PROPOSED CEILING. COORDINATE LOCATION WITH EXISTING "T"

PRE-CAST SECOND FLOOR CONCRETE SECTIONS.

3. PROVIDE AND INSTALL NEW PIPING HCS&R, CONDENSATE PIPING

AND PUMP AND CONNECT TO NEW PLUMBING PIPING AND CONNECT TO

NEW FAN COIL UNIT.

4. COORDINATE UNIT PLACEMENT AND INSTALLATION WITH CEILING

GRID, PROPOSED LIGHTING AND ABOVE CEILING CLEARANCES. INSTALL

UNIT IN THE WAY TO MAKE FILTER REPLACEMENT AND ROUTINE

MAINTENANCE EASILY ACCESSIBLE.

5. INSTALL NEW VERTICAL FCU AND RECONNECT TO EXISTING

HCS&R AND CONDENSATE PIPING.

1

2

3

4

5

SCALE:

MS BUILDING

MECHANICAL AND PLUMBING NEW WORK ROOF PLAN

1/8"=1'-0"

1

M3

ITEM SPECIFIC NOTES:

1. PROVIDE AND INSTALL NEW 4" VENT THROUGH EXISTING

CONCRETE ROOF. COORDINATE PENETRATION, DRILLING AND VENT

LOCATION WITH EXISTING CRAWL SPACE, FIRST, & SECOND FLOOR

WALL AND CEILING CONDITIONS. PROVIDE FLASHING AND SEAL

OPENING TO MAKE IT WATER TIGHT IN ORDER TO COMPLETE

INSTALLATION. SEE RELATED FLOOR PLAN AND DETAIL DRAWINGS FOR

MORE INFO.

ROOF

ELLIPSE

CENTERLINE (TYP.)

ROOF

ELLIPSE

CENTERLINE (TYP.)

EXISTING

CHILLER

ENCLOSURE

FLAT ROOF

FLAT ROOF

EXISTING

CHILLER

SCALE:

MS BUILDING BUILDING

CRAWL SPACE PLUMBING DEMO PLAN

1/8"=1'-0"

1

M4

ITEM SPECIFIC NOTES:

1. DEMOLISH EXISTING 5" CLEANOUT AND VERTICAL SANITARY PIPE

IN THE AMOUNT NEEDED AND PREPARE FOR A NEW 4" HORIZONTAL PIPE

CONNECTION FITTING AND CLEANOUT INSTALL.

1

1

SCALE:

MS BUILDING BUILDING

CRAWL SPACE NEW WORK PLUMBING PLAN

1/8"=1'-0"

1

M5

ITEM SPECIFIC NOTES:

1. INSTALL NEW VERTICAL 5" PIPE SECTION WITH CLEANOUT AND A

"Y" FITTING THAT WILL ACCOMODATE NEW HORIZONTAL CONNECTION

AND TIE INTO EXISTING PIPE AT SLAB.

2. PROVIDE AND INSTALL NEW 4" VENT/SANITARY PIPE UP THROUGH

EXISTING CONCRETE FLOOR. COORDINATE PENETRATION, DRILLING

AND VENT LOCATION WITH EXISTING CRAWL SPACE, FIRST, & SECOND

FLOOR WALL AND CEILING CONDITIONS. PROVIDE SLEVES AND SEAL

OPENING TO MAKE IT WATER TIGHT IN ORDER TO COMPLETE

INSTALLATION. SEE RELATED FLOOR PLAN, ROOF AND RISER DETAIL

DRAWINGS FOR MORE INFO.

3. PROVIDE AND INSTALL 1 1/2" CW PIPE FROM MECHANICAL ROOM

BELOW CRAWL SPACE CEILING TO A PROPOSED LOCATION.

COORDINATE PIPE PENNETRATION WITH EXISTING CONCRETE BEAMS

AND PROPOSED ARCHITRECTURAL FLOOR PLAN. PROVIDE SLEEVE AND

SEALS.

4. PROVIDE AND INSTALL NEW 1 1/2" SANITARY PIPE UP THROUGH

EXISTING CONCRETE FLOOR. COORDINATE PENETRATION, DRILLING

AND VENT LOCATION WITH EXISTING CRAWL SPACE & FIRST FLOOR

WALL AND CEILING CONDITIONS AND PROPOSED ARCHITECTURAL

PLANS. PROVIDE SLEVES AND SEAL OPENING TO MAKE IT WATER TIGHT

IN ORDER TO COMPLETE INSTALLATION. SEE RELATED FLOOR PLAN AND

DETAIL DRAWINGS FOR MORE INFO.

5. USE EXISTING CRAWL SPACE VENTS OPENINGS (REMOVE AND

REINSTALL VENTS-PREFERRABLY ON THE BACK OF THE BUILDING) AND

EXISTING MECHANICAL ROOM ACCESS HATCH FOR MATERIAL/PIPING

INTRODUCTION INTO CRAWL SPACE AREA.

FIRST FLOOR CW AND HWBPLUMBING PLAN

FIRST FLOOR CW AND HWBPLUMBING PLAN

SCALE:

MS BUILDING

NEW MALE & FEMALE HEADS CW & HW PIPING PLAN

1/8"=1'-0"

1

M8

SCALE:

MS BUILDING

NEW MALE & FEMALE HEADS SANITARY PLAN

1/8"=1'-0"

2

M8

SCALE:

MS BUILDING

NEW MECHANICAL ROOM PIPING PLAN

1/8"=1'-0"

3

M8

MALE

HEAD

FEMALE

HEAD

GALLERY

RECRUIT

WAITING

AREA

001

002

003

004

MALE

HEAD

FEMALE

HEAD

GALLERY

RECRUIT

WAITING

AREA

001

002

004

MECHANICAL

ROOM

004

POINT OF CONNECTION

POINT IF DEMOLITION

POINT IF DEMOLITION (CAP)

INCREASE IN PIPE SIZE

GENERAL NOTES:

1. ALL WORK IS TO BE PERFORMED PER LAST EDITION OF

PLUMBING CODE.

2. RUN ALL PIPING ABOVE CEILING INSULATED.

3. COORDINATE ALL INSTALLATION, ROUGH-IN HEIGHTS WITH ADA

REQUIREMENTS AND ARCHITECTURAL DRAWINGS, ELEVATIONS

AND EXISTING CONDITIONS.

4. CONNECT VENTING PIPING TO ALL FIXTURES THAT REQUIRE

VENT CONNECTIONS.

5. INSTALL SLEEVES AND FIRESTOPPING FOR ALL PIPING

PENETRATIONS THROUGH WALLS.

6. COORDINATE WC FIXTURE ROUGH-IN AND SEWAGE EJECTOR

PLACEMENT AND CONNECTING PIPING LENGTHS WITH

REQUIRED SLOPING AND MAX. SANITARY PIPE LENGTHS.

7. PROVIDE ISOLATION BALL VALVES REQUIRED FOR

FIXTURE MAINTENANCE AND SERVICING FOR ALL

CONNECTION PIPING.

NEW WORK NOTES:

1. RUN SANITARY DISCHARGE AT 1% SLOPE TO PROPOSED

LOCATION. PROVIDE 2 INCH "WYE" FITTING AND INSTALL ABOVE

CEILING INTO AN EXISTING AUXILIARY VENT. ENSURE PROPER

OPERATION UPON COMPLETION OF FORCED SANITARY PIPE UPON

COMPLETION.

2. CONNECT NEW 1 1/2" COLD WATER (CW) PIPE ABOVE CEILING AND RUN

ALONG SANITARY LINE TO WORK AREA.

4. PROVIDE NEW VENT THROUGH ROOF (VTR) INTO EXISTING ROOF

SYSTEM, INSTALL NECESSARY FLASHING, CAULK AND SEAL OPENING

IN ORDER TO PREVENT LEAKS. RESET THE SHINGLES IN ORDER TO

COMPLETE INSTALLATION.

5. RUN 1 " CONDENSATE LINE FROM FCU-2 TO A FUNNEL AND CONNECT

TO A LAVATORY TAIL PIPE.

REQUIRED WALL SUPPORT TO COMPLETE INSTALLATION.

6. COORDINATE INSTALLATION HEIGHT PIPES SUPPORT AND ROUTING

WITH EXISTING CONDITIONS AND UTILITIES.

C

1

M7

SCALE:

DEMOLITION GSK/ESO TESTING OFFICE

MECHANICALDEMOLITION PLAN-GSK BUILDING

3/16"=1'-0"

DEMOLITION NOTES:

1. FAN COIL UNIT CURRENTLY

BALANCED AT 1200 CFM AND ALL EXISTING

CONNECTIONS ARE TO REMAIN AND TO BE

MODIFIED TO SUIT INSTALLATION. SEE NEW

WORK DRAWING AND NOTES FOR MORE

INFO.

2. ALL NEW WALLS ARE TO BE BUILT

BELOW EXISTING DUCTWORK AND TO BE

COORDINATED WITH IT. EXISTING

DUCTWORK INSULATION IS TO BE

REMOVED AND DISPOSED, IN ORDER FOR

DUCT TO BE REPAIRED AND REINSULATED.

SEE NEW WORK NOTES FOR MORE INFO.

3. EXISTING DIFFUSER/REGISTER AND

CONNECTED DUCT TO BE TEMPORARILY

DISCONNECTED FROM EXISTING GRID AND

MODIFIED AS NEEDED TO SUIT THE

INSTALLATION. SEE NEW WORK DRAWING

AND NOTES FOR MORE INFO.

4. EXISTING THERMOSTAT IS TO BE

TEMPORARY DISCONNECTED &

RELOCATED TO A NEW LOCATION. Repair

EXISTING WALL, PATCH AND PAINT TO A

COLOR MATCHING EXISTING. SEE NEW

WORK DRAWING.

NEW WORK NOTES:

1. FAN COIL UNIT IS TO BE BALANCED TO 1000 CFM. MAINTAIN UNIT ACCESS CLEARANCE AND EXISTING OUTSIDE AIR, RS&lL AS NEEDED AND COORDINATE

OVER NEWLY ERECTED WALL. RE-SEAL EXISTING UN IT'S FLEXIBLE CONNECTIONS AND RE-ALLIGN THE UNIT AND IT'S AUXILLIARY DRAIN PAN AND MAKE

CONDENSATE REMOVAL EFFICIENT. RECONNECT RETURN REGISTER TO UNIT UPON NEW WALL CREATION.

2. PROVIDE EXISTING PAS DIFFUSER MATCHING INSULATION ACCESSORY (FOR ATTIC INSTALLATION) AND NEW FLEXIBLE DUCT AND INSTALL IT INTO NEW

CEILING GRID. COORDINATE FLEX DUCTWORK LENGTHS WITH EXISTING DUCTWORK TAKEOFFS. BALANCE DIFFUSER TO VOLUME SHOWN. SEE DEMO DRAWING

AND NOTES FOR MORE INFO.

3. PROVIDE DOOR WITH INTERNAL 24X24 TRANSFER LOUVER.

4. RELOCATE EXISTING THERMOSTAT TO NEW LOCATION.

5. UPON REMOVAL OF EXISTING DUCTWORK INSULATION, SEAL WITH THICK MASTIC COATING ALL EXISTING DUCTWORK CONNECTIONS. REINSULATE

DUCTWORK TO COMPLETE INSTALLATION.

6. REBALANCE THE UNIT TO 1000 CFM AND EXISTING RETURN AND RELOCATED AND INSULATED DIFFUSERS TO SHOWN AIR VOLUME ( CFM).

7. INSTALL EXISTING THERMOSTAT TO A PROPOSED LOCATION. REUSE / EXTEND WIRING TO COMPLETE INSTALLATION. EXISTING INTERLOCK WITH EXHAUST

FAN SERVING THE STORAGE BATHROOM (HEAD 1-013) ARE TO REMAIN.

8. PROVIDE A DUOSTAT (TEMPERATURE AND HUMIDITY CONTROLLER)THAT WILL OPERATE FAN WHEN ATTIC TEMPERATURE REACHES 60% OR 110° F.

1

2

3

4

GENERAL GSK NEW WORK NOTES:

A. ALL EXISITING DUCTWORK IS TO BE REPAIRED AT JOINTS AND UNIT

CONNECTIONS. THICK COATING OF MASTIC IS TO BE APPLIED AT

LOCATIONS WHERE SHEET METAL SCREWS ARE PENETRATING

DUCTWORK.

B. UNIT'S THERMOSTAT IS TO BE RE-INTERLOCKED WITH EXISTING FAN AND

UNIT SERVING LUCKY BAG STORE.

C. EXISTING GSK DUCTWORK IS TO BE REINSULATED WITH 2" THICK

INSULATION UPON MASTIC APPLICATION.

D. PROVIDE INSULATING PLENUM ACCESSORY FOR EXISTING DIFFUSERS

WHICH ARE TO BE REINSTALLED AT PROPOSED LOCATIONS INTO NEW

CEILING GRID.

2

M7

SCALE:

PROPOSED GSK/ESO TESTING OFFICE

PROPOSED MECHANICAL PLAN

3/16"=1'-0"

OPEN AREA

015

HEAD 1

013

HEAD 2

014

015

OPEN AREA

015

HEAD 1

013

HEAD 2

014

IT ROOM

012

TECH CLO.

015

3

1

2 2

33

HEAD 1

013

HEAD 2

014

IT ROOM

012

015

HEAD 1

013

HEAD 2

014

IT ROOM

012

TECH CLO.

015

GENERAL GSK DEMOLITION NOTES:

A. EXISTING UNITS AND DUCTWORK ARE POORLY INSTALLED AND ARE LEAKING AIR AT UNIT, DUCTWORK AND REGISTER CONNECTIONS,

CAUSING EXCESS CONDENSATION OF CURRENT INSULATION JACKETING IN SUMMER AND EXCESSIVE SWEATING AND DRIPPING. GOAL

FOR WORK SHOWN IS TO REPAIR AND SEAL DUCTWORK AND ALL UNIT CONNECTIONS, REINSULATE DUCTS AS WELL AS PROVIDE NEW

FLEX CONNECTIONS AND INSULATION ACCESSORY FOR ALL EXISTING REGISTERS.

B. EXISTING GSK AIR HANDLING UNITS\ WHICH DUCTWORK IS TO BE MODIFIED AND REBALANCED ARE LOCATED UNDER A SLOPED ROOF

CLOSE TO CEILING (AT 8 FT. ABOVE FINISHED FLOOR (AFF).

C. UNIT'S THERMOSTAT IS INTERLOCKED WITH EXISTING FAN AND UNIT SERVING LUCKY BAG STORE. tHESE INTERLOCKS ARE TO REMAIN

UPON THERMOSTAT RELOCATION.

D. EXISTING GSK DUCTWORK IS LEAKING AIR AND INSULATION IS COMPROMISED. CONTRACTOR IS TO DEMOLISH AND DISPOSE EXISTING

INSULATION. IT WAS MANUFACTURED IN 4' SECTIONS.

E. EXISTING DIFFUSERS WHICH ARE TO BE TEMPORARELY DISCONECTED, MODEL PAS BY TITUS ARE TO BE SALVAGED AND REINSTALLED

IN PROPOSED LOCATIONS INTO NEW CEILING GRID.

F. FOR ALL ELECTRICAL POWER AND FIRE ALARM DEMOLITION REQUIREMENTS, REFER TO ELECTRICAL DRAWINGS.

LUCKY BAG

MAIN STORE AREA

011

LUCKY BAG

MAIN STORE AREA

011

011

LUCKY BAG

STORAGE

012

2

2

3

3

011011

011

LUCKY BAG

STORAGE

012

GENERAL NOTES:

1. ALL WORK TO BE INSTALLED PER LATEST NATIONAL STANDARD

PLUMBING CODE EDITION.

4 4

POWER POLE

PROJECTOR

4

SPEAKER,

TYP OF 2

DEMOLISH SURFACE

MOUNT CONDUIT & WIRE

BETWEEN RECEPTACLES

PANEL C

PANEL D

TELECOMMUNICATIONS

DATA PORT, TO BE MOVED

T

V

UNK

C-6

UNK

C-17,23

SC

RE

EN

ESO

TESTING AREA

ESO

OFFICE

VETERANS

OFFICE

SP

SP

FCU

D-25

H-6

PANEL H

OPEN

OFFICE SPACE

TELECOMM

CLOSET

HEAD

HEAD

H-4

PANEL H

EX

S

H-11

EX EX EX EX

EXEXEXEX

EX

SSS

SS

SS

TESTING IN

PROGRESS SIGN

PANEL C

PANEL D

D-12

UNKD-22

MISSION SUPPORT DEMOLITION NOTES:

1. DEMOLISH RECEPTACLES SHOWN ON PLAN UNLESS NOTED OTHERWISE. FOR SURFACE MOUNTED RECEPTACLES, DEMOLISH

SURFACE MOUNTED CONDUIT AND BOXES. FOR FLUSH MOUNTED RECEPTACLES ON WALLS SLATED TO REMAIN, PROVIDE NEW

STAINLESS STEEL BLANK FACEPLATES. DEMOLISH WIRE BACK TO PANEL OR FIRST JUNCTION BOX FEEDING OTHER DEVICES

SLATED TO REMAIN. DEMOLISH ABANDONED CONDUIT.

2. DEMOLISH MC CABLE BACK TO SOURCE FEEDING THE ONE FAN COIL UNIT SHOWN ON THIS DRAWING. MC CABLE IS RUN IN CRAWL

SPACE. PATCH HOLE IN FLOOR. DISCONNECT AND RECONNECT POWER TO THE FOUR FAN COIL UNITS IDENTIFIED ON THE

MECHANICAL DRAWINGS TO BE TEMPORARILY MOVED.

3. DEMOLISH TWO POWER POLES.

4. PROJECTOR IS HARD WIRED TO CIRCUIT IN JUNCTION BOX ABOVE SUSPENDED CEILING. DEMOLISH WIRE FROM JUNCTION BOX TO

PROJECTOR. REMOVE PROJECTOR AND VIDEO CABLE AND REINSTALL AT GSK.

5. REMOVE TWO SPEAKERS AND REINSTALLED AT GSK.

6. MOVE ONE TELECOMMUNICATIONS DATA PORT TO LOCATION SHOWN ON NEW WORK DRAWING.

7. DEMOLISH REMAINING TELECOMMUNICATIONS DATA PORTS SHOWN ON PLAN. DEMOLISH SURFACE MOUNTED CONDUIT AND

BOXES. DEMOLISH CAT 5E CABLE BACK TO PUNCH DOWN BLOCKS LOCATED IN ROOM APPROXIMATELY 100 FEET AWAY.

8. DEMOLISH EXISTING 2X4 RECESSED LIGHT FIXTURES. DEMOLISH WIRE AND ABANDONED CONDUIT BACK TO TOGGLE SWITCHES.

9. REMOVE TESTING IN PROGRESS SIGN TO BE REINSTALLED AT GSK. DEMOLISH WIRE BACK TO SWITCH AND PATCH HOLE IN WALL.

10. DEMOLISH EXISTING TOGGLE SWITCHES. DEMOLISH WIRE BACK TO NEAREST JUNCTION BOX. DEMOLISH ABANDONED CONDUIT.

EXISTING CIRCUITS TO BE REUSED FOR NEW LIGHTS. IF NECESSARY TO CONSTRUCT NEW WALL, REMOVE SWITCH BOX AND

PATCH HOLE IN BLOCK WALL.

GENERAL NOTES:

1. ALL THE EXISTING POWER AND LIGHTING CIRCUITS FEEDING THE

MISSION SUPPORT ESO SPACES ORIGINATE IN ELECTRICAL PANEL "C"

OR "D". ALL POWER AND LIGHTING CIRCUITS FEEDING THE GSK OFFICE

SPACES ORIGINATE IN ELECTRICAL PANEL "H". CONTRACTOR SHALL

TRACE OUT CIRCUITS AS NECESSARY TO IDENTIFY.

2. THE MISSION SUPPORT CRAWL SPACE IS CONSIDERED A CONFINED

SPACE. REFER TO THE SPECIFICATIONS FOR CONFINED SPACE

REQUIREMENTS.

3. ARC FLASH LABELS IDENTIFYING THE ENERGY LEVEL AND APPROPRIATE

CATEGORY ARE INSTALLED ON THE ELECTRICAL EQUIPMENT. THE

CONTRACTOR SHALL WEAR THE APPROPRIATE PPE IN ACCORDANCE

WITH NFPA 70E WHILE WORKING ON ANY ENERGIZED EQUIPMENT.

GSK DEMOLITION NOTES:

1. DEMOLISH TWO RECEPTACLES, BOXES AND CONDUIT. DEMOLISH WIRE BACK TO FIRST JUNCTION BOX

FEEDING OTHER DEVICES SLATED TO REMAIN.

2. REMOVE EXISTING 2X4 RECESSED LIGHT FIXTURES AND REINSTALL IN LOCATIONS SHOWN ON NEW WORK

PLAN. EXISTING WIRE AND CONDUIT MAY BE REUSED PROVIDED IT IS IN GOOD CONDITION.

3. REMOVE EXISTING EXIT SIGN AND REINSTALL IN LOCATION SHOWN ON NEW WORK PLAN. DEMOLISH WIRE

BACK TO NEAREST JUNCTION BOX AND RECONNECT CIRCUIT. PROVIDE STAINLESS STEEL BLANK FACEPLATE

ON EXISTING BOX.

4. DEMOLISH ONE EXISTING TOGGLE SWITCH. DEMOLISH WIRE BACK TO NEAREST JUNCTION BOX AND

RECONNECT CIRCUIT. PROVIDE STAINLESS STEEL BLANK FACEPLATE ON EXISTING BOX. EXISTING CIRCUITS

TO BE REUSED FOR NEW LIGHTS.

SCALE:

MS ESO SPACE, POWER &

COMM DEMOLITION PLAN

1/4"=1'-0"

SCALE:

GSK OFFICE, POWER

DEMOLITION PLAN

1/4"=1'-0"

SCALE:

GSK OFFICE, LIGHTING

DEMOLITION PLAN

1/4"=1'-0"

TELECOMM

CLOSET

SCALE:

MS ESO SPACE, LIGHTING

DEMOLITION PLAN

1/4"=1'-0"

MISSION SUPPORT NEW WORK NOTES:

1. PROVIDE NEW FLUSH MOUNT RECEPTACLES WHERE SHOWN. GFI RECEPTACLES SHALL BE MOUNTED 6"

ABOVE LAVATORIES. PROVIDE NEW BOXES, STAINLESS STEEL FACEPLATES, AND MC CABLE. CONNECT

RECEPTACLES TO EXISTING CIRCUITS.

2. PROVIDE NEW SURFACE MOUNT RACEWAY AND WIRE NEAR NEW DOOR TO RECONNECT EXISTING

RECEPTACLES TO EXISTING CIRCUITS.

3. PROVIDE NEW LOW VOLTAGE TRANSFORMER(S) ABOVE SUSPENDED CEILING AS NEEDED FOR HANDS FREE

FIXTURES. PROVIDE LOW VOLTAGE WIRE (NOT SHOWN) TO SENSOR / ACTUATOR FOR EACH LAVATORY AND

WATER CLOSET IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. REFER TO MECHANICAL

DRAWINGS.

4. PROVIDE NEW #10 AWG MC CABLE HOME RUNS FOR NEW INSTANT HOT WATER HEATERS. CONNECT WIRING

TO EXISTING SPARE 20A CIRCUIT BREAKERS. THE CIRCUIT BREAKER AND WIRE SIZE STATED HEREIN IS BASED

ON A SPECIFIC BASIS OF DESIGN HEATER. IF THE MECHANICAL CONTRACTOR PROVIDES HEATERS THAT

REQUIRE LARGER CIRCUIT BREAKERS / WIRE, THE ELECTRICAL CONTRACTOR SHALL UPGRADE THE BRANCH

CIRCUITS AT NO ADDITIONAL COST TO THE GOVERNMENT. REFER TO DRAWING E4 FOR LOCATION OF PANEL J.

REFER TO MECHANICAL DRAWINGS.

5. MOVE ONE EXISTING TELECOMMUNICATIONS DATA PORT TO LOCATION SHOWN. PROVIDE NEW FLUSH MOUNT

BOX AND 3/4" EMT CONDUIT INSIDE WALL TO A POINT ABOVE THE SUSPENDED CEILING. ROUTE EXISTING CAT

5E CABLES THROUGH NEW CONDUIT. COAST GUARD PERSONNEL WILL TERMINATE AND TEST CABLES.

6. RE-SECURE ONE EXISTING SURFACE MOUNT TELECOMMUNICATIONS CONDUIT TO WALL. PROVIDE NEW BLANK

FACEPLATE ON EXISTING BOX.

7. PROVIDE ONE NEW TOGGLE SWITCH, BOX, AND MC CABLE. CONNECT TO HALLWAY FIXTURE.

8. PROVIDE NEW DUAL TECHNOLOGY OCCUPANCY SENSORS AND POWER PACKS. PROVIDE NEW 2X4 RECESSED

LED LIGHT FIXTURES. PROVIDE NEW MC CABLE AND CONNECT TO EXISTING CIRCUITS. TEST / ADJUST

OCCUPANCY SENSORS FOR PROPER OPERATION. REFER TO REFLECTED CEILING PLAN FOR EXACT LOCATION

OF NEW FIXTURES.

9. PROVIDE IDENTIFICATION LABELS FOR NEW ELECTRICAL CIRCUITS AND DATA PORTS IN ACCORDANCE WITH

THE SPECIFICATIONS.

PANEL C

PANEL D

GFI

GFI

4

TELECOMMUNICATIONS

DATA PORT, RELOCATED

SEE NOTE 5

C-17,23

C-6

UNK

TX

TX

PANEL C

PANEL D

C

B

A

A

A

A

A A

A

B

B

MD1

MD1

S

MD1

PP

PP

D-22

D-12

PP

2x4 RECESSED LIGHT FIXTURE, LETTER INDICATES

FIXTURE TYPE

2x4 RECESSED LIGHT FIXTURE WITH EMERGENCY

BATTERY PACK, LETTER INDICATES FIXTURE TYPE

2x2 RECESSED LIGHT FIXTURE, LETTER INDICATES

FIXTURE TYPE

DOORWAY LIGHT FIXTURE

EXIT SIGN, WALL MOUNTED

SINGLE POLE TOGGLE SWITCH

THREE-WAY TOGGLE SWITCH

MOTOR STARTER SWITCH

TELECOMMUNICATIONS DATA PORT, 4 JACKS

EXISTING TELECOMMUNICATIONS DATA PORT, TO REMAIN

C

S

S

3

DUPLEX RECEPTACLE

EXISTING RECEPTACLE, TO REMAIN

QUAD RECEPTACLE

GFI RECEPTACLE

ELECTRICAL PANEL, PANEL LETTER INDICATED

HOMERUN, PANEL AND CIRCUIT # INDICATED

DISCONNECT SWITCH, NON-FUSED, RATING INDICATED

EXHAUST FAN MOTOR

DUAL TECHNOLOGY, PASSIVE INFRARED AND ULTRASONIC,

OCCUPANCY SENSOR WITH 12' RADIAL COVERAGE, CEILING

MOUNTED

POWER PACK, MOUNTED ABOVE SUSPENDED CEILING

LOW VOLTAGE TRANSFORMER FOR HANDS FREE FIXTURES

PNL A

A-31

EF

A

B

30DW

LUMINAIRE SCHEDULE

C

2x2, LED TYPE, CEILING MOUNTED TROFFER WITH

0.125" THICK ACRYLIC LENS

RECESSED

2x4, LED TYPE, CEILING MOUNTED TROFFER WITH

0.125" THICK ACRYLIC LENSB

TYPE DESCRIPTION

RECESSED

MOUNTING

120 1

120

LAMPS VOLTS

5

QTY

LED, 4300 LUMENS,

39 WATT, 4000K, 110

LPW

LED, 3300 LUMENS,

35 WATT, 4000K, 102

LPW

DW

SURFACE 120 1

DOORWAY WALLPACK LIGHT, LED, UL WET LISTED,

SWIVEL PHOTOCELL, BRONZE ALUMINUM HOUSING,

POLYCARBONATE LENS, -40°F STARTING TEMP, 5 YEAR

WARRANTY

LED, 2508 LUMENS,

18 WATT, 5000K, 124

LPW, 100,000 L70

2x4, LED TYPE, CEILING MOUNTED TROFFER WITH

0.125" THICK ACRYLIC LENSA

RECESSED 120 7

LED, 3000 LUMENS,

32 WATT, 4000K, 115

LPW

EX

EXISTING LIGHT FIXTURE, TO REMAIN

S

M

MD1

PP

LEGEND

SCALE:

MS ESO SPACE, POWER &

COMM NEW WORK PLAN

1/4"=1'-0"

SCALE:

MS ESO SPACE, LIGHTING

NEW WORK PLAN

1/4"=1'-0"

TX

GSK NEW WORK NOTES:

1. PROVIDE NEW FLUSH MOUNT RECEPTACLES IN WALLS WHERE SHOWN. PROVIDE ONE NEW RECEPTACLE

ABOVE SUSPENDED CEILING WHERE SHOWN. PROVIDE NEW BOXES, STAINLESS STEEL FACEPLATES, AND MC

CABLE. CONNECT RECEPTACLES TO CIRCUITS SHOWN. CIRCUIT H-18 IS A NEW CIRCUIT; CONNECT TO SPARE

SINGLE POLE, 20A CIRCUIT BREAKER IN PANEL.

2. PROVIDE NEW TOGGLE SWITCH DISCONNECT FOR EXHAUST FAN LOCATED ABOVE SUSPENDED CEILING.

PROVIDE NEW MC CABLE BACK TO PANEL AND CONNECT TO SPARE SINGLE POLE, 20A CIRCUIT BREAKER.

REFER TO MECHANICAL DRAWINGS FOR EXHAUST FAN CONTROL.

3. MOUNT PROJECTOR AND SPEAKERS IN LOCATIONS SHOWN. PROVIDE NEW PLUG ON PROJECTOR POWER

CORD. PROVIDE NEW SURFACE MOUNT CONDUIT FROM SUSPENDED CEILING TO 12 INCHES ABOVE FLOOR IN

CORNER NEAR SPEAKER. PROVIDE NEW SPEAKER WIRE AND CONNECT SPEAKERS TO COAST GUARD

EQUIPMENT LOCATED IN SAME CORNER AS SURFACE MOUNT CONDUIT. RECONNECT EXISTING VIDEO CABLE

FROM PROJECTOR TO COAST GUARD EQUIPMENT.

4. PROVIDE THREE NEW FLUSH MOUNT, QUAD TELECOMMUNICATIONS DATA PORTS AND CAT 5e CABLE. RUN

BLUE CAT 5e CABLES FOR ONE QUAD DATA PORT BACK TO TELECOMMUNICATIONS CLOSET. COAST GUARD

PERSONNEL WILL TERMINATE THESE CABLES ON THE EXISTING SWITCH. PROVIDE NEW WALL MOUNT, 16

PORT, GIGABIT SWITCH WHERE SHOWN. RUN PINK CAT 5e CABLES FOR TWO QUAD DATA PORTS BACK TO NEW

16 PORT SWITCH AND TERMINATE. TEST CABLES AND JACKS IN ACCORDANCE WITH THE SPECIFICATIONS.

5. RELOCATE EXISTING LIGHT FIXTURES AND EXIT SIGN AS SHOWN.

6. PROVIDE NEW LIGHT FIXTURES AND SWITCHES WHERE SHOWN. PROVIDE NEW BOXES, STAINLESS STEEL

FACEPLATES AND MC CABLE. CONNECT LIGHTING FIXTURES TO EXISTING CIRCUIT. WIRE EXISTING 2X4

EMERGENCY FIXTURES SUCH THAT THEY TURN OFF WITH THE SWITCH.

7. MOUNT TESTING IN PROGRESS SIGN WHERE SHOWN AND CONNECT TO DEDICATED SWITCH.

8. PROVIDE IDENTIFICATION LABELS FOR NEW ELECTRICAL CIRCUITS AND DATA PORTS IN ACCORDANCE WITH

THE SPECIFICATIONS.

H-6

H-18

PANEL H

PROJECTOR

SC

RE

EN

7'

OFFICE

TELECOMM

CLOSET

HEAD

HEAD

TESTING

AREA

OFFICE

HALLWAY

MOUNT ABOVE

SUSPENDED CEILING

SPEAKER,

TYP OF 2

SP

SP

MOUNT THIS RECEPTACLE 6"

BELOW SUSPENDED CEILING

SURFACE CONDUIT

IN THIS CORNER

SWITCH

WALL MOUNT, 16 PORT,

GIGABIT SWITCH

S

M

H-19

PANEL H

EX

H-11

B

EX

EX

EX

EX

B

S

EX

EX

EX

EX

S

S

S

EX

3

3

S

DW

S

TESTING IN

PROGRESS SIGN

ab

S

a

a

b

b

SCALE:

GSK OFFICE, POWER

NEW WORK PLAN

1/4"=1'-0"

SCALE:

GSK OFFICE, LIGHTING

NEW WORK PLAN

1/4"=1'-0"

PANEL I

PANEL J

S

M

J-7

S

M

HVAC POWER CONSTRUCTION NOTES:

1. PROVIDE NEW TOGGLE SWITCH DISCONNECTS FOR HVAC EQUIPMENT. THE FAN

COIL UNIT AND THE EXHAUST FAN ARE LOCATED ABOVE THE SUSPENDED CEILING.

REFER TO MECHANICAL DRAWINGS FOR HVAC EQUIPMENT CONTROL.

2. PROVIDE ONE RECEPTACLE ABOVE SUSPENDED CEILING NEXT TO THE FAN COIL

UNIT FOR THE ASSOCIATED CONDENSATE PUMP.

3. PROVIDE NEW MC CABLE WIRING BACK TO PANEL "J" AND CONNECT TO EXISTING

SPARE SINGLE POLE, 20A CIRCUIT BREAKER.

SCALE:

MS FIRST FLOOR,

POWER TO HVAC EQUIP.

3/32"=1'-0"

E

ESO

TESTING AREA

ESO

OFFICE

VETERANS

OFFICE

1-8

1-10

1-12

1-13

AV4

30CD

AV4

15CD

1-11

HEAD

OPEN

OFFICE SPACE

TELECOMM

CLOSET

HEAD

1-9

1-12

1-8

1-10

1-13

AV4

30CD

AV4

30CD

AV4

30CD

AV4

15CD

1-19

1-20

1-21

HEAD

TELECOMM

CLOSET

HEAD

TESTING

AREA

OFFICE

OFFICE

HALLWAY

1-11

1-9

WAITING AREA

HEAD

HEAD

HALLWAY

GENERAL NOTES:

1. BOTH BUILDINGS WILL BE OCCUPIED THROUGHOUT THE CONTRACT. CONTRACTOR SHALL MAKE EVERY

EFFORT TO MINIMIZE THE AMOUNT OF TIME THE FIRE ALARM SYSTEMS ARE TURNED OFF AND SHALL NOT

LEAVE ANY PORTION OF THE SYSTEMS TURNED OFF OVERNIGHT. IF NECESSARY, CONTRACTOR SHALL

PROVIDE TEMPORARY CONNECTIONS TO RECONNECT EXISTING FIRE ALARM CIRCUITS DURING

CONSTRUCTION.

2. CONTRACTOR SHALL PROVIDE THE SERVICES OF A NJ LICENSED ELECTRICIAN OR A NICET LEVEL II FIRE

ALARM SYSTEMS CERTIFIED TECHNICIAN WITH A MINIMUM OF THREE YEARS RELEVANT EXPERIENCE TO WORK

ON THE FIRE ALARM SYSTEMS.

3. COAST GUARD PERSONNEL WILL PROGRAM THE CONTRACTOR PROVIDED NEW ADDRESSABLE DEVICES AND

THE EXISTING FIRE ALARM CONTROL PANEL. CONTRACTOR SHALL TEST ALL NEW DEVICES AND A SAMPLING

OF THE EXISTING DEVICES. ALL TESTING SHALL BE WITNESSED BY THE CONTRACTING OFFICER'S

REPRESENTATIVE.

4. FIRE ALARM CABLES SHALL BE INSTALLED IN ONE CONTINUOUS LENGTH (NO SPLICES) BETWEEN TERMINATION

POINTS. FIRE ALARM CIRCUITS SHALL NOT BE T-TAPPED. INITIATION CIRCUITS SHALL USE #16 AWG

CONDUCTORS AND NOTIFICATION CIRCUITS SHALL USE #14 AWG CONDUCTORS.

5. CURRENTLY, THERE ARE NO TROUBLE CONDITIONS BEING REPORTED ON THE FIRE ALARM CONTROL PANELS.

CONTRACTOR SHALL TROUBLESHOOT AND CORRECT ANY TROUBLE CONDITIONS THAT APPEAR DURING

CONSTRUCTION.

6. REFER TO REFLECTED CEILING PLAN FOR EXACT LOCATION OF DETECTORS.

GSK CONSTRUCTION NOTES:

1. THE GSK BUILDING USES ADDRESSABLE FIRE ALARM INITIATION DEVICES ON CLASS B (2 WIRE), SIGNALING

LINE CIRCUITS AND NOTIFICATION DEVICES ON CLASS B (2 WIRE) NOTIFICATION APPLIANCE CIRCUITS. FIRE

ALARM RATED MC CABLE IS USED THROUGHOUT. PROTECT EXISTING DEVICES DURING CONSTRUCTION.

2. MOVE ONE EXISTING PULL STATION TO LOCATION SHOWN AND FLUSH MOUNT BOX IN NEW WALL. DEMOLISH

ABANDONED CABLE AND PROVIDE STAINLESS STEEL BLANK FACEPLATE ON EXISTING BOX.

3. MOVE ONE EXISTING HORN / STROBE TO LOCATION SHOWN AND SURFACE MOUNT ON EXISTING BLOCK WALL.

DEMOLISH ABANDONED CABLE AND PROVIDE STAINLESS STEEL BLANK FACEPLATE ON EXISTING BOX.

4. MOVE TWO EXISTING SMOKE DETECTORS (ADDRESSES 1-9 & 1-11) TO LOCATIONS SHOWN IN SUSPENDED

CEILING. IF NECESSARY, PROVIDE NEW CABLES TO REACH NEW LOCATIONS WITHOUT SPLICING.

5. PROVIDE THREE NEW ADDRESSABLE SMOKE DETECTORS AND BASE PLATES. NEW DETECTORS ARE SHOWN

ON DRAWING AS ADDRESSES 1-19, 1-20, AND 1-21.

6. PROVIDE TWO NEW STROBES AND FLUSH MOUNT ON EXISTING WALL.

7. PROVIDE NEW FIRE ALARM RATED MC CABLE AND BOXES. FOR SURFACE MOUNTED HORN / STROBE, PROVIDE

SURFACE MOUNT CONDUIT AND BOX. CONNECT NEW DEVICES TO EXISTING FIRE ALARM CIRCUITS WITHOUT

CREATING ANY T-TAPS.

8. LABEL EACH NEW SMOKE DETECTOR WITH THE CORRECT ADDRESS (IE 1-19). LABEL EACH NEW STROBE WITH

THE AUDIO / VISUAL ZONE NUMBER (IE AV4). INSTALL LABELS SUCH THAT THEY ARE VISIBLE WITH THE DEVICES

INSTALLED. INSTALL ADDRESS LABELS ON BASE PLATES. INSTALL AV ZONE NUMBERS DIRECTLY ON STROBES.

9. TEST NEW DEVICES IN ACCORDANCE WITH SPECIFICATIONS.

MISSION SUPPORT CONSTRUCTION NOTES:

1. THE MISSION SUPPORT BUILDING USES CONVENTION FIRE ALARM DEVICES WITH ZONED, CLASS B (2 WIRE),

INITIATING DEVICE CIRCUITS. PROTECT EXISTING SMOKE DETECTOR DURING CONSTRUCTION.

2. MOVE EXISTING SMOKE DETECTOR TO LOCATION SHOWN.

3. PROVIDE THREE NEW CONVENTIONAL TYPE SMOKE DETECTORS AND BASE PLATES. PROVIDE FIRE ALARM

RATED MC CABLE AND BOXES. CONNECT NEW DETECTORS TO EXISTING FIRE ALARM CIRCUIT WITHOUT

CREATING ANY T-TAPS.

4. TEST SMOKE DETECTORS IN ACCORDANCE WITH SPECIFICATIONS.

SMOKE DETECTOR

HEAT DETECTOR

PULL STATION

STROBE

HORN / STROBE

KEY

SCALE:

MS ESO SPACE, EXISTING

FIRE ALARM PLAN

1/4"=1'-0"

SCALE:

GSK OFFICE, EXISTING

FIRE ALARM PLAN

1/4"=1'-0"

SCALE:

GSK OFFICE, NEW

FIRE ALARM PLAN

1/4"=1'-0"SCALE:

MS ESO SPACE, NEW

FIRE ALARM PLAN

1/4"=1'-0"