Upload
simplymail
View
217
Download
0
Embed Size (px)
Citation preview
8/8/2019 Rems 4
1/27
Remote Monitoring System
8/8/2019 Rems 4
2/27
About The Product
This version of the RMS is basically dedicatedfor the collection of the data from every slavesconnected to it, i.e. it is now master device of
the whole setup.
Its main function is to collect data from all of
the devices and send it on our server by themean of GPRS link.
8/8/2019 Rems 4
3/27
8/8/2019 Rems 4
4/27
About The Product
It communicates with all of the devices on
RS485.
It gives a command on the 485 bus which isconnected with every devices. The command
consists ofa device ID on its initialbyte and
according to that ID the respective device will
give its response.
8/8/2019 Rems 4
5/27
Main Features :
It provides SMS feature to us so that even inthe link is down we will have the currentstatus of the site.
It gives us the feature of Local storage so thatevery data is stored and safe in any case.
We can configure all of the slaves connected
with DENEB remotely. We can configure some settings of DENEB
with the help of SMS also.
8/8/2019 Rems 4
6/27
Main Features :
To add or to Remove any device from the 485 busis now very simple. The only thing which isrequired is that the new device must supports the
MODBUS protocol. Just by adding its configuration file which
contents its settings we can plug a new device.
It sends the data of every device after a regular
interval. If due to any change in the status ofanydevice packet a new event packet is generatedand instantly transmitted on server.
8/8/2019 Rems 4
7/27
Slaves Connected with The Master:
Digital Input Output Board (DIO).
RF-ID (ASM).
AC Energy Meter. Access Control System (ibutton-ACS).
DC Energy Meter.
Battery Monitoring System (BMS).
Fuel Sensor.
8/8/2019 Rems 4
8/27
MASTER (DENEB)
1. DIO
2. AMS
7. FUEL
SENSOR
6. BMS
5. DC ENERGY
METER
4. ACCESS
CONTROL
SYSTEM
3. AC ENERGY
METER
Connection Sequence of the slaves
8/8/2019 Rems 4
9/27
Masters (Deneb)Description :
THE DENEB FRONT VIEW
Ethernet
SlotUSB Slot
RF Antenna
connector
Slot for SIM
For MMC
Card
8/8/2019 Rems 4
10/27
Masters (Deneb) Description (Front):
Connect Antenna cable properly at RF antennaConnector.
Insert SIM in SIM socket.
The Ethernet slot is used to connect theDeneb with our PC/Lap top.
With USB slot we can attach the CDMA
modem or ant USB device which is supportedby Deneb.
In MMC slot Micro SD card is inserted.
8/8/2019 Rems 4
11/27
Masters (Deneb) Description :
12 V
SupplyRS-485
ConnectorRS-232
Connector
BACK SIDE VIEW
8/8/2019 Rems 4
12/27
Masters Description (Back side) :
There is phone jack a connector for 12V
power supply.
There isa
Red colored LED which indic
ates the
power ON state of the Deneb.
The RS-485 connector is basically used as the
communication connector. All of the
communication wire finally terminates on this
DB-9 Male connector.
8/8/2019 Rems 4
13/27
Slaves Description 1. DIO
Connector for
Communication
16-
DigitalInputs
4-Rela
yOutput
Power Connector
Connector of
Temperature sensor
8/8/2019 Rems 4
14/27
DIO DB-9 Female connector is used to communicate the
DIO with Deneb. This output is given to a 232-485converter which finally this o/p is connected to main485-Bus .
Its device ID is 52.
This device gives the 24-digital alarms i/p and 8digital o/p. Also it senses the temperature and givesthe current room temperature reading.
There is a bit of change in the hardware of the DIO.
Here we have to verify that the o/p of the Relay no. 1must be N & NC instead o f N & O .
8/8/2019 Rems 4
15/27
2. AMS (RF-ID)
Tags Of
RF-ID
For communication
8/8/2019 Rems 4
16/27
RF-ID (AMS)
This device is basically consist ofactive tags
which transmits their dataafter every
configured time interval Its device ID is 55.
With the help of this module we can assure
the presence ofany device in which the tag isattached.
8/8/2019 Rems 4
17/27
3. AC Energy Meter :
8/8/2019 Rems 4
18/27
AC Energy Meter :
This device is used to measure mainly R Y B
voltages and EB Energy and DG Energy.
Its device ID is1
7.
8/8/2019 Rems 4
19/27
4. Access Control System :
I-Button And its Reader
8/8/2019 Rems 4
20/27
Access Control System :
This device controls the access ofa person in
the shelter. Until the i-Button is applied the
door does not opens.
Its device ID is 51.
8/8/2019 Rems 4
21/27
5. DC Energy Meter :
8/8/2019 Rems 4
22/27
DC Energy Meter :
This device is basically used to measure DC
voltage, DC Current and DC energy.
Its device ID is 01.
8/8/2019 Rems 4
23/27
8/8/2019 Rems 4
24/27
Battery Monitoring System :
Its main function is to monitor the status of
the battery of the site.
It gives us the Charging and discharging
current needed by battery.
Its device ID is 65.
8/8/2019 Rems 4
25/27
7. Fuel Sensor :
8/8/2019 Rems 4
26/27
Fuel Sensor :
It senses the level of fuel.
It also communicates on RS485.
Its Device ID is 49.
8/8/2019 Rems 4
27/27
8. Logical Packet
This packet consists of the datalike Fuel Top-
up and Drain-out, Low PP Battery alarm, High
temperature alarm, Low fuelalarm.
Whenever the parameters of this packet
changes this packet is transmitted on the
server.