Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
56"
Instruction ManualSAFETY GUIDELINES AND INSTALLATION PROCEDURES
RCF-LE800-5BL
REMOTE CONTROL CEILING FAN WITH LIGHT
13
WHAT YOU HAVE Please checkout following parts after opening the box:
COMPONENTS
PARTS QUANTITY 1.DOWNROD 12.TOP CANOPY 1
4. FAN HOUSING & MOTOR1
7. BLADE HOLDERS
3. COUPLING COVER
5. SWITCH COVER
6. GLASS SHADE
8. BLADES9. BLADE DECORATIVE COVERS
11
5A. LIGHT KIT & LED LAMP(7W) 1
5
55
SCREW PACKAGE
SCREW PACKAGE
13.BLADE HOLDER SCREWS 11
12. S BLADE DECORATIVE COVER CREWS 16
QUANTITY
14.EXPANSION J HOOK
10.PARTS QUANTITY
1
1
1
15.BALANCING KIT 1
15
DIGITAL TOUCH SCREEN REMOTE (COMES WITH 3V BATT X2)
12
14
11. RF RECEIVER 1
Page 1
10A. REMOTE HOLDER WITH 2 MOUNTING SCREWS
FAN SIZE VOLTAGE CARTON WEIGHT
56” 80W 250+-10% 8.13kg 9.13kg
MAX. FAN POWER
MAX SPEED (RPM)
PRODUCT WEIGHT
220 240V/50Hz
2
1
8
3
4
7
5
HI
MED
LOW
OFF
1H
3H
6H 10
9
10A
6
5A
11
LIGHT POWER
7W Led
Double pole single throw switch(Breaker Switch)
Earth
Ceiling Fan
Wall Switch (OFF/ON)
240VAC/50HzPower Supply
Page 2
1 ) Please do not install the ceiling fan at high humidity areas. 2 ) Distance between fan blades and ground must be at least 2.5 meter and above.3 ) Do not touch fan blades with any objects when the ceiling fan is spinning. 4 ) To minimize the chances of electrical shock, power switch must be OFF before installing or dismantling the ceiling fan or any electrical wiring connection. 5 ) All electrical connections must conform to the national electrical safety codes. To prevent electrical shock, earth wire must be installed correctly (suitable for power supply of 240V AC/50Hz). 6 ) To ensure your personal safety and optimize functions of the ceiling fan, assembly and installation by qualified technician is highly recommended. 7 ) Only direct connection to wall switch is allowed. Please refer to diagram below.
WARNING
1 ) Do not bend the blade holders during installation, blades balancing or fan cleaning.2 ) To prevent accidents, power switch must be OFF before ceiling fan installation. 3 ) Ceiling fan installation and electrical wiring must be done by qualified technician in accordance with all applicable codes and air conditioning engineers (ASHRAE) or the local qualified authorities. 4 ) Be cautious when drilling the wall to avoid damaging electrical wiring and other hidden parts. 5 ) Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on plaster ceiling or any types of drywall ceilings. During ceiling fan installation, all screws must be tightened at all allocated parts.
8 ) This product is not provided with cord, plug or other means for disconnection from the supply. Connecting or changing power cord or lead wire, must be done by qualified personnel in order to avoid hazard. 9 ) This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.10 ) Children should be supervised to ensure that they do not play with the appliance.11 )
A). TO ENSURE YOUR PERSONAL SAFETY, PLEASE READ THROUGH THEINSTRUCTION MANUAL BEFORE USE
B). SAFETY GUIDELINES
The ceiling fan must be installed with means for disconnection incorporated in the fixed wiring(wall switch)in accordance with the wiring rules.
Page 3
DIAGRAM 2
1 ) Remove 1st hex-head screw along with the fixings (pin, metal nut, lock washer and metal washer) from the downrod. 2 ) Remove the pin on 2nd hex-head screw and loosen the other fixings.
1 ) Lift the fan until the hanging wheel seat on the mounted J hook.2 ) Install the 1st hex-head screw together with fixings. 3 ) Tighten up the 2nd hex-head screw and fixing.
DIAGRAM 1
DIAGRAM 3
Safety Cable C
Wire
Light Connector
onnector
Top Canopy
Coupling Cover
Screw x 2
Hex-head Screw
Motor Coupling
The 1st Hex-head Screw
PinMetal Nut
Metal Nut
Lock WasherMetal Washer
The 2nd Hex-head Screw
Pin
Terminal Block
Fixings
Screw (Loosen)
(Tighten)
Hook
The 1st Hex-head Screw
The 2nd Hex-head Screw
1 ) Loosen 2 screws on the motor coupling.2 ) Insert the downrod through top canopy and coupling cover. 3 ) Thread the safety cable through the downrod. 4 ) Connect both wire and light connectors from downrod to fan motor.5 ) Lock the downrod to the motor coupling, tighten up with 2 hex-head screws and fixings.6 ) Tighten 2 screws on the motor coupling.7 ) Slide down the coupling cover until it rest on top of the fan housing.
Downrod
Installation without proper procedures as above mentioned might result to fan loosening or falling.
INSTALLATION PROCEDURESBefore ceiling fan installation,please go through the procedures in detail with picture diagram as reference.
STEP 1 (See Diagram 1)
STEP 2 (See Diagram 2)
STEP 3 (See Diagram 3)
WARNING:
Metal Washer
PinMetal NutLock Washer
Fixings
Note:-
2. Hook must be installed on concrete ceiling.
(2.5 Nm torque for hex-head screws and Metal Nut)
1. Remember to lock the pin after tightening hex-head screws.
Page 4
Fit the connected receiver into top canopy. Then, tighten the screw on downrod.
DIAGRAM 5
DIAGRAM 4
Receiver
Ceiling
Ceiling
Ceiling
Receiver
Receiver
Receiver
Receiver
Brown Wire(TO MOTOR L)
Blue W
(Orange Wire)(FOR LIGHT)
ire(TO MOTOR N)
Red / Brown Wire(Incoming LIVE Wire)
Black / Blue Wire(Incoming NEUTRAL Wire)
Green Wire(Incoming EARTH Wire)
Red Wire (AC in L)
Black Wire (AC in N)
Terminal Block (marked )“L”
Terminal Block (marked )“N”
Terminal Block (marked )“ ”
FROM TO
! Connect the Motor Wiring to Receiver first!Connect wiring as below:-
Downrod
Receiver
T
Screw
op Canopy
LIV
E w
ire
(Red
/ B
row
n)
NE
UT
RA
L w
ire
(Bla
ck /
Blu
e )
Terminal Block (marked )“
”
STEP 4 (See Diagram 4)
SUPPLY CIRCUIT
STEP 5 (See Diagram 5)
E
AR
TH w
ire
LN
LN
LN
FOR
LIG
HT
FOR
LIG
HT
OrangeGreen
BrownBlue
Receiver
Page 5
Blade holder
Fan Blade
Decorative Cover
DIAGRAM 7
Switch CoverKey Hole 1
Mounting Ring
Key Hole 2
Fan Motor
Fan Motor
Fan MotorBlade Holder
Fan Blade
Decorative Cover
Screw
Screw
Screw
Orange Blue
Blue
Light kitLed lamp
BLack
ScrewX10
Plastic Block(Must Remove)
DIAGRAM 8
DIAGRAM 9
DIAGRAM 6
1 ) Screw the blade holder onto the fan blade and decorative cover. 2 ) Repeat same step on all the remaining fan blades.
1 ) Rem
to the blue wire from
ove 1 screw from the mounting ring and loosen the other 2 (Do not remove). 2 ) Place the key hole 1 of switch coverthrough the 2 loosen screws and twist to lock in place. 3 ) Tighten u
black wire from light kit.
p all screws including the one removed earlier.
5 ) Tighten up all screws including the o
Install the glass shade by twisting clockwise(To unlock, twist anticlockwise).
ne removed earlier.
4 ) Remove the 1 screws on key hole 2(Do not remove). and loosen the other 2
Connect the blue wireConnect the
from motor housing light kit.
orange wire from motor housing to the
1 ) Remove all the plastic blocks and 10 screws from the motor housing. 2 ) Place assembled fan blades onto the motor housing and tighten up all screws removed previously.
Note:- 1. There are total of 10 screws holding fan blades to the motor housing. 2. Plastic blocks must be removed and discarded.
STEP 6 (See Diagram 6)
STEP 7 (See Diagram 7)
STEP 8 (See Diagram 8)
STEP 9 (See Diagram 9)Switch Cover
Glass shade
Page 6
WARNING!FASTEN THE SAFETY CABLE TO THE MOUNTED J HOOK FOR
SAFETY PURPOSES.
Page 7
FLOOR
MIN 2.5m
SAFETY TIPS
Please ensure the distance between fan blade and ground must be at least 2.5meter and above.