Upload
dinhhanh
View
218
Download
0
Embed Size (px)
Citation preview
IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Regutec
2
RegutecThe Regutec lockshield is used in pumped warm water heating and air conditioning systems.
Key features
> Easy to operate with an allan key size 5 AF
> Presettable by means of shut-off and regulation cone
> Body made of corrosionresistant gunmetal
> Also available in Press version with Viega SC-Contur
Technical description
Radiator lockshield for shut-off and regulation. Operation of the shut-off/regulation cone with an allan key size 5 AF.
Versions with female thread DN 10 to DN 20, with male thread G3/4 / DN 15 and Viega press connection with SC-Contur 15 mm / DN 15 in angle and straight form. Length according to DIN 3842.
Sealing on stems by means of EPDM O-rings. Body made of corrosion-resistant gunmetal.
With the model with a female thread, it is possible to make a connection to a threaded pipe. With the model with compression fittings, a connection can be made to a copper, precision steel or multi-layer pipe. With the model with a male thread, it is also possible to make
a connection to a plastic pipe using compression fittings. Versions with Viega press connection (15 mm) with SC-Contur are suitable for copper, Viega Sanpress stainless steel and Prestabo steel pipes.
Permitted operating temperature TB 120°C (248°F), with press connection TB 110 °C (230°F).
Permitted operating pressure PB 10 bar.
Contruction
Regutec
1. Closing cap2. EPDM O-ring3. Shut-off/regulation cone4. Body made of corrosion resistant
nickel plated gunmetal
3
Application
The Regutec lockshield is used in pumped warm water heating and air conditioning systems.Versions with female thread from DN 10 to DN 20, male thread G3/4 / DN 15 and Viega press connection 15 mm / DN 15 in angle and straight form make the threadedconnection suitable for versatile and varied applications.It enables individual shut-off, for example of radiators, so that decorating and service work can be carried out without interruption to the operation of other radiators.A special combination of shut-off/regulation cone and valve seat enables it to be used as a shut-off fitting as well as for hydraulic balance. At the same time, the aim is met of supplying all heaters with hot water according to their requirement.
Sample application
1. Regutec2. Thermostatic valve
Press-Line Connection with Viega SC-ConturRegutec radiator lockshields with 15 mm Viega press connec-tion are suitable for copper pipes conforming to EN 1057 as well as Viega Sanpress stainless steel and Prestabo steel pipes.All press connections as well as the valve bodies are made of corrosion-resistant, dezincification-free gunmetal. Since this is a Viega press connection, all suitable Viega press-fitting jaws can be used. This means there is no need to purchase costly press-fitting tools and jaws.The pressing action is produced by a formed hexagon recess before and after the beading of the connector and gives the press-fitted joint the necessary strength. In addition, the press-fitting beading is specifically formed such as to give the highgrade EPDM sealing element its defined shape.In the interest of safety, the press connections are equipped with SC-Contur (SC = safety connection) which makes it possible to detect non-pressed joints by visible leaks when filling the system. During the press-fitting operation, the SC-Contur is
practically reformed and looses its effect in the process, thus producing a permanent, tight and positive joint connection.Initially, press-fitting joints that do not feature SC-Contur can appear to be tight in the non-pressed state, however, they can slide apart during subsequent operation of the system.The hexagon on the valve bodies is a particularly practical feature for holding the fittings while tightening the union nut.The following press-fitting tools can be used, e.g.– Viega: Type 2, PT3-H, PT3-EH, PT3-AH, battery-powered
Presshandy, Pressgun 4E/4B– Geberit: PWH 75– Geberit /Novopress: Type N 230V, Type N battery-powered– Mapress/Novopress: EFP 2, ACO 1/ ECO 1– Klauke: UAP 2The suitability of other press-fitting tools should be verified with the respective manufacturer. We recommend using only Viega press-fitting jaws to make Viega press connections.
NoteTo avoid damage and the formation of stones in hot water systems the composition of the heating medium should comply to VDI guidelines 2035. For industrial and long distance energy systems the VdTÜV-Explanatory Leaflet 1466/AGFW-Explanatory Leaflet 5/15 must be observed.Mineral oils, or greases of all types containing mineral oil, in the
heating medium lead to severe swelling and, in most cases, to failure of the EPDM seals. When using nitrite-free frost and corrosion protective substances based on ethylene glycol, the appropriate information, especially about the concentration of individual additives, is to be taken from the manufacturer’s documentation for frost and corrosion protection.
Operation
Shut-offThe Regutec lockshield is operated with an allan key size 5 AF. By turning clock-wise the lockshield is closed. If the lockshield has been set for hydraulic balancing, the appropriate number of revolutions during closing has to be determined. It can then be ensured that the initial setting can be set again.
RegulationFor continuously variable regulation the lockshield is closed with the allan key size 5 AF and then opened by the required number of revolutions. The number of revolutions to set can be determined from the diagrams/technical data. The factory setting as delivered is fully open.
IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Regutec
4
Technical data
Diagram DN 10 (3/8”)Angle / Straight*) Revolution setting
Diagram DN 15 (1/2”)Angle / Straight*) Revolution setting
5
Diagram DN 20 (3/4”)Angle / Straight*) Revolution setting
DN Kv-valueRevolution setting [U]
Kvs ζ-value(open)
Permitted operatingtemperatureTB [°C]
PermittedoperatingpressurePB [bar]
0,25 0,5 1 1,5 2 2,5 3 3,5
10 (3/8”) 0,22 0,37 0,62 0,92 1,19 1,36 1,47 1,58 1,68 13,8 120 10
15 (1/2”) 0,22 0,37 0,62 0,92 1,22 1,43 1,57 1,68 1,74 34,6 120 10
20 (3/4”) 0,22 0,37 0,62 0,92 1,27 1,55 1,72 1,85 1,93 93,2 120 10
*) referred to threaded pipe according to DIN 2440.
Calculation exampleRequired: revolution setting DN 20
Given: differential pressure to choke off Δp = 34 mbarheat flow Q = 2440 W temperature spread Δt = 15 K (70/55°C)
Solution: mass flow m = Q / (c · Δt) = 2440 / (1,163 · 15) = 140 kg/hrevolution setting = 1,25 (from diagram)
Cv =
Kv = Cv · 0,86
Kv
0,86
IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Regutec
6
Articles
Angle
DN Kvs EAN Article No
10 (3/8”) 1,68 4024052416028 0355-01.00015 (1/2”) 1,74 4024052416127 0355-02.00020 (3/4”) 1,93 4024052416226 0355-03.000
Anglewith Viega press connection 15 mm
DN Kvs EAN Article No
15 (1/2”) 1,74 4024052545322 0345-15.000
Anglewith male thread G 3/4
DN Kvs EAN Article No
15 (1/2”) 1,74 4024052499526 0365-02.000
Straight
DN Kvs EAN Article No
10 (3/8”) 1,68 4024052416325 0356-01.00015 (1/2”) 1,74 4024052416424 0356-02.00020 (3/4”) 1,93 4024052416523 0356-03.000
Straightwith Viega press connection 15 mm
DN Kvs EAN Article No
15 (1/2”) 1,74 4024052545414 0346-15.000
Straightwith male thread G 3/4
DN Kvs EAN Article No
15 (1/2”) 1,74 4024052499625 0366-02.000
7
Accessories
Compression fittingfor copper or precision steel pipes.Female thread connection Rp 3/8 – Rp 3/4.Metal-to-metal joint.Brass nickel-plated.Support sleeves should be used for a pipe wall thickness of 0.8 – 1 mm. Follow the specifications of the pipe manufacturer.
Ø Pipe DN EAN Article No
12 10 (3/8”) 4024052174614 2201-12.35115 15 (1/2”) 4024052175017 2201-15.35116 15 (1/2”) 4024052175116 2201-16.35118 20 (3/4”) 4024052175215 2201-18.351
Compression fittingfor copper or precision steel pipes.Male thread connection G 3/4.Metal-to-metal joint. Nickel-plated brass.Support sleeves should be used for a pipe wall thickness of 0.8 – 1 mm. Follow the specifications of the pipe manufacturer.
Ø Pipe EAN Article No
12 4024052214211 3831-12.35115 4024052214617 3831-15.35116 4024052214914 3831-16.35118 4024052215218 3831-18.351
Support sleevefor copper or precision steel pipe with a 1 mm wall thickness. Brass.
L Ø EAN Article No
25,0 12 4024052127016 1300-12.17026,0 15 4024052127917 1300-15.17026,3 16 4024052128419 1300-16.17026,8 18 4024052128815 1300-18.170
Compression fittingfor copper or precision steel pipes. Male thread connection G 3/4.Soft sealed. Nickel-plated brass.
Ø Pipe EAN Article No
15 4024052515851 1313-15.35118 4024052516056 1313-18.351
Compression fittingfor plastic pipes.Male thread connection G 3/4.Nickel plated brass.
Ø Pipe EAN Article No
14x2 4024052134618 1311-14.35116x2 4024052134816 1311-16.35117x2 4024052134915 1311-17.35118x2 4024052135110 1311-18.35120x2 4024052135318 1311-20.351
Compression fittingfor multi-layer pipes.Nickel-plated brass.
Ø Pipe EAN Article No
Male thread connection G 3/416x2 4024052137312 1331-16.351Female thread connection Rp 1/216x2 *) 4024052138616 1335-16.351
*) can be used for valve from 04.1995
IMI HEIMEIER / Thermostatic Heads & Radiator Valves / Regutec
Dimensions
Dimensions according to DIN 3842 range 1
angle form straight form
DN D d2 l2 l3 l4 l5 H H1 SW1 SW2 SW3
10 Rp3/8 R3/8 75 52 22 43 26 22 27 1915 Rp1/2 R1/2 80 88 58 26 47 26 27 30 1920 Rp3/4 R3/4 90,5 65,5 28,5 49,5 26 32 37 19
SW = Spanner opening
1 mm = 0,0394 inch
The products, texts, photographs, graphics and diagrams in this document may be subject to alteration by IMI Hydronic Engineering without prior notice or reasons being given. For the most up
to date information about our products and specifications, please visit www.imi-hydronic.com.
4230-18.483 ed.2 10.2017
SW3
H
L5
SW2
G 3/4
L4
d2
SW3
H
L5
SW2
D
L4
d2
SW1
SW3
D
H1
SW2SW1
L2
d2
0355
0365
SW3
G 3 /
4
H1
SW 2
L3
d2
52
73
L4
d2
15
22
SW2SW3
SW1
0345
0356
0366
0346
d 2
106
H1
15
22
SW3SW2SW1