Register your product and get support at ... · compuertas de tiro (registros) ... Montaje en la pared o cielorraso - El aparato se debe montar en ... • When stand mounting the

Register your product and get support at

www.philips.com/welcome32PFL3605/77

32PFL3615/77

42PFL3605/77

42PFL3615/77

EN User manual

Dali_77_EN_2.indd Sec3:1 4/6/2010 11:14:31 AM

Ejemplo de conexión a tierra de la

antena según NEC,

Código Eléctrico Nacional

INSTRUCCIONES DE SEGURIDAD IMPORTANTELea antes de operar el equipo

1. Lea estas instrucciones.

2. Guarde estas instrucciones.

3. Preste atención a todas las advertencias.

4. Siga todas las instrucciones.

5. No use este aparato cerca del agua.

6. Límpielo solamente con un paño seco.

7. No bloquee ninguno de los orificios de ventilación. Instálelo de

acuerdo con las instrucciones de los fabricantes.

8. No lo instale cerca de fuentes de calor, tales como radiadores,

compuertas de tiro (registros) de calor, estufas u otros aparatos

(incluidos amplificadores) que generen calor.

9. No anule el objetivo de seguridad del enchufe polarizado o de

conexión a tierra. Un enchufe polarizado tiene dos paletas, una

más ancha que la otra. Un enchufe de conexión a tierra tiene dos

paletas y una tercera espiga de conexión a tierra. La paleta más ancha

o la tercera espiga es entregada para su seguridad. Si el enchufe

suministrado no se ajusta a su tomacorriente, consulte a un electricista

para que reemplace el tomacorriente obsoleto.

10. Evite pisar o apretar el cable de suministro eléctrico, especialmente en

los enchufes, tomacorrientes y el punto en que salen del aparato.

11. Sólo use aditamentos o accesorios especificados por el fabricante.

12. Utilice sólo un carro, soporte, trípode, repisa o mesa

especificados por el fabricante o que se vendan junto

con el aparato. Si usa el carro, tenga precaución cuando

mueva la combinación carro/aparato para evitar lesiones

si éste se vuelca.

13. Desenchufe este aparato durante las tormentas eléctricas o cuando no

se use durante largos períodos.

14. Deje que personal calificado realice todo el servicio. Es necesario

que el aparato reciba servicio si se ha dañado en algún modo, como

cuando se daña el cable o enchufe de suministro de corriente, se ha

derramado líquido u objetos han caído dentro él, cuando el aparato ha

estado expuesto a lluvia o humedad, no opera bien o se ha caído.

15. Es posible que este producto contenga plomo y mercurio. La

eliminación de estos materiales podría estar regulada debido a

consideraciones medioambientales. Para obtener información

acerca de la eliminación o del reciclaje, póngase en contacto con sus

autoridades locales o con la Alianza de Industrias Electrónicas: en

www.eiae.org

16. Daños que requieran servicio - El aparato debe recibir servicio de

personal de servicio calificado cuando:

A. Se ha dañado el cable de alimentación o el enchufe; o

B. Han caído objetos o se ha derramado líquido dentro del aparato; o

C. El aparato ha quedado expuesto a la lluvia; o

D. El aparato parece no funcionar normalmente o su rendimiento ha

cambiado notoriamente; o

E. Se ha dejado caer el aparato o se ha dañado la caja.

17. Inclinación/estabilidad - Todos los televisores deben cumplir con

las normas de seguridad generales recomendadas internacionalmente

en cuanto a las propiedades de inclinación y estabilidad del diseño de

su gabinete.

• No comprometa estas normas de diseño aplicando una fuerza de

tracción excesiva a la parte delantera o superior del gabinete lo que

finalmente puede hacer que el producto se vuelque.

• Además, no se ponga en peligro usted mismo o a sus niños colocando

equipos electrónicos o juguetes sobre el gabinete. Dichos artículos

pueden caer inesperadamente desde la parte superior del producto y

dañar el producto y/o causar lesiones personales.

18. Montaje en la pared o cielorraso - El aparato se debe montar en

una pared o cielorraso únicamente como lo recomienda el fabricante.

19. Líneas de energía eléctrica - Una antena exterior se debe ubicar

lejos de las líneas de energía.

20. Conexión a tierra de la antena exterior - Si se conecta una

antena exterior o un sistema de cable al producto, asegúrese de

que la antena o el sistema de cable estén conectados a tierra para

proporcionar cierta protección contra sobrevoltajes y acumulación de

cargas electrostáticas. En la Sección 810 del Código Eléctrico Nacional,

ANSI/NFPA 70, se proporciona información sobre la adecuada

conexión a tierra de las esteras y estructuras de apoyo, conexión a

tierra del alambre de acometida a una unidad de descarga de antena,

tamaño de los conectores de conexión a tierra, ubicación de la unidad

de descarga de antena, conexión a los electrodos y requerimientos del

electrodo de conexión a tierra. Vea la Figura que aparece más abajo.

21. Entrada de objetos y líquidos - Se debe tener cuidado de que no

caigan objetos dentro de los orificios de la caja ni se derramen líquidos

a través de ellos.

a) Advertencia: Para reducir el riesgo de incendios o de descarga

eléctrica, este aparato no se debe exponer a la lluvia ni a la humedad, y

no se le deben colocar encima objetos llenos de líquido como jarrones.

22. Uso de las baterías PRECAUCIÓN - Para evitar escapes de

las baterías que pueden resultar en lesiones corporales, daño a la

propiedad o a la unidad:

• Instale correctamente todas las baterías, con los polos + y - alineados

como está marcado en la unidad.

• No mezcle las baterías (nuevas con antiguas o de carbono con

alcalinas, etc.).

• Retire las baterías cuando no use la unidad por un largo tiempo.

Nota para el instalador del sistema CATV: Se hace este recordatorio para llamar la atención del instalador del sistema CATV sobre el

Artículo 820-40 de donde se proporcionan instrucciones para la apropiada conexión a tierra y, en particular, se especifica que la tierra de los

cables se conectará al sistema de conexión a tierra del edificio tan cerca del punto de entrada del cable como sea posible.

ABRAZADERAS DE TIERRACONDUCTOR DE ENTRADA DE LA ANTENA

UNIDAD DE DESCARGA DE LA ANTENA

CONDUCTOR DE TIERRA

ABRAZADERAS DE TIERRA

SISTEMA DE ELECTRODO DE PUESTA ATIERRA DEL SUMINISTRO ELECTRICO

CAJA DE LA ENTRADA DELSUMINISTRO ELECTRICO

Dali_77_warranty.indd 2 4/6/2010 11:58:33 AM

1

7 Connect devices 20 Back connector 20 Side connector 21 Connect a computer 22 Use Philips EasyLink 23 Use a Kensington lock 24

8 Product information 25 Supported display resolutions 25 Multimedia 25 Tuner/Reception/Transmission 25 Remote control 25 Power 25 Supported TV mounts 26 Product speci� cation 26

9 Troubleshooting 27 General TV issues 27 TV channel issues 27 Picture issues 27 Sound issues 28 HDMI connection issues 28 Computer connection issues 28 Contact us 28

10 Index 29

Contents 1 Notice 2

2 Important 3

3 Your TV 5 Side controls and indicators 5 Remote control 5

4 Use your TV 7 Switch your TV on/off or to standby 7 Switch channels 7 Watch connected devices 8 Adjust TV volume 8

5 Use more of your TV 9 Access TV menus 9 Remove devices from the home menu 9 Change picture and sound settings 9 Create and use list of favorite channels 11 Use the TV clock 12 Use timers 12 Use TV locks 13 View closed captions (subtitles) 14 View photos and play music from a

USB storage device 14 Update the TV software 16 Change TV preferences 16 Start a TV demo 17 Reset the TV to factory settings 17

6 Install channels 18 Select TV tuner 18 Automatically install channels 18 Manually install channels 18 Rename channels 19 Rearrange channels 19

Engl

ish

EN

Dali_77_EN_2.indd 1 4/6/2010 11:14:31 AM

2

Copyright All other registered and unregistered trademarks are the property of their respective owners. ® Kensington and Micro Saver are registered US trademarks of ACCO World corporation with issued registrations and pending applications in other countries throughout the world. Portions of this software are copyright © The FreeType Project (www.freetype.org).

HDMI, and HDMI logo and High-De� nition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.

1 Notice 2010 © Koninklijke Philips Electronics N.V. All rights reserved. Speci� cations are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly. The material in this manual is believed adequate for the intended use of the system. If the product, or its individual modules or procedures, are used for purposes other than those speci� ed herein, con� rmation of their validity and suitability must be obtained. Philips warrants that the material itself does not infringe any United States patents. No further warranty is expressed or implied. Philips cannot be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible. Pixel characteristics This LCD product has a high number of color pixels. Although it has effective pixels of 99.999% or more, black dots or bright points of light (red, green or blue) may appear constantly on the screen. This is a structural property of the display (within common industry standards) and is not a malfunction. Warranty No components are user serviceable. Do not open or remove covers to the inside of the product. Repairs may only be done by Philips Service Centres and of� cial repair shops. Failure to do so shall void any warranty, stated or implied. Any operation expressly prohibited in this manual, any adjustments, or assembly procedures not recommended or authorised in this manual shall void the warranty.

EN

Dali_77_EN_2.indd 2 4/6/2010 11:14:31 AM

3

Risk of injury or damage to the TV! Two people are required to lift and carry • a TV that weighs more than 55 lbs. When stand mounting the TV, use only • the supplied stand. Secure the stand to the TV tightly. Place the TV on a � at, level surface that can support the combined weight of the TV and the stand. When wall mounting the TV, use only a • wall mount that can support the weight of the TV. Secure the wall mount to a wall that can support the combined weight of the TV and wall mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage.

Risk of injury to children! Follow these precautions to prevent the TV from toppling over and causing injury to children:

Never place the TV on a surface covered • by a cloth or other material that can be pulled away. Ensure that no part of the TV hangs over • the edge of the surface. Never place the TV on tall furniture (such • as a bookcase) without anchoring both the furniture and TV to the wall or a suitable support. Educate children about the dangers of • climbing on furniture to reach the TV.

Risk of overheating! Never install the TV in a con� ned space. • Always leave a space of at least 4 inches or 10 cm around the TV for ventilation. Ensure curtains or other objects never cover the ventilation slots on the TV.

Risk of damage to the TV! Before you connect the TV to the power • outlet, ensure that the power voltage matches the value printed on the back of the TV. Never connect the TV to the power outlet if the voltage is different.

2 Important Read and understand all instructions before you use your TV. If damage is caused by failure to follow instructions, the warranty does not apply.

Safety Risk of electric shock or � re!

Never expose the TV to rain or water. • Never place liquid containers, such as vases, near the TV. If liquids are spilt on or into the TV, disconnect the TV from the power outlet immediately. Contact Philips Consumer Care to have the TV checked before use. Never place the TV, remote control or • batteries near naked � ames or other heat sources, including direct sunlight. To prevent the spread of � re, keep candles or other � ames away from the TV, remote control and batteries at all times.

Never insert objects into the ventilation • slots or other openings on the TV. When the TV is swiveled ensure that • no strain is exerted on the power cord. Strain on the power cord can loosen connections and cause arcing.

Risk of short circuit or � re! Never expose the remote control or • batteries to rain, water or excessive heat. Avoid force coming onto power plugs. • Loose power plugs can cause arcing or � re.

Engl

ish

EN

Dali_77_EN_2.indd 3 4/6/2010 11:14:31 AM

4

Disposal of your old product and batteries

Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.

When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health.

Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste. Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health.

Risk of injury, � re or power cord damage! Never place the TV or any objects on the • power cord. To easily disconnect the TV power cord • from the power outlet, ensure that you have full access to the power cord at all times. When you disconnect the power cord, • always pull the plug, never the cable. Disconnect the TV from the power • outlet and antenna before lightning storms. During lightning storms, never touch any part of the TV, power cord or antenna cable.

Risk of hearing damage! Avoid using earphones or headphones at • high volumes or for prolonged periods of time.

Low temperatures If the TV is transported in temperatures • below 5°C, unpack the TV and wait until the TV temperature matches room temperature before connecting the TV to the power outlet.

Screen care Avoid stationary images as much as • possible. Stationary images are images that remain on-screen for extended periods of time. Examples include: on-screen menus, black bars and time displays. If you must use stationary images, reduce screen contrast and brightness to avoid screen damage. Unplug the TV before cleaning.• Clean the TV and frame with a soft, • damp cloth. Never use substances such as alcohol, chemicals or household cleaners on the TV. Risk of damage to the TV screen! Never • touch, push, rub or strike the screen with any object. To avoid deformations and color fading, • wipe off water drops as soon as possible.

EN

Dali_77_EN_2.indd 4 4/6/2010 11:14:31 AM

5

Remote control

a ( Standby-On )

Switches the TV to standby if it is on.• Switches on the TV if it is in standby.•

b MENU Toggles the main menu on or off.

c INCR. SURR Enables Incredible Surround for stereo sources. Enables spatial mode for mono sources.

1

4

6

910

11

12

13

7

8

23

21

22

17

16

15

14

201918

5

3 Your TV Congratulations on your purchase, and welcome to Philips! To fully bene� t from the support that Philips offers, register your TV at www.philips.com/welcome.

This section gives you an overview of commonly used TV controls and functions.

Side controls and indicators

a +/- : Increases or decreases volume.

b ( Home ): Toggles the home menu on or off.

c P/CH +/- : Switches to the next or previous channel.

d ( Power ): Switches the product on or off. The product is not powered off completely unless it is physically unplugged.

e Standby indicator and remote control sensor.

5

2

1

3

4

Engl

ish

EN

Dali_77_EN_2.indd 5 4/6/2010 11:14:31 AM

6

s TV/PC Toggles between PC mode and previously viewed video mode.

t SLEEP Sets a delay after which the TV switches to standby.

u FORMAT Toggles through available picture formats. Some formats are not available for some picture sources.

v DEMO Toggles the demonstration menu on or off.

Remote control usage When using the remote control, hold it close to the TV and point it at the remote control sensor. Make sure that the line-of-site between the remote control and TV is not blocked by furniture, walls or other objects.

~5m

~30˚

d SOURCE Selects connected devices.

e SAP ( Secondary audio program ) Selects Secondary Audio Program (SAP)/ Stereo/ Mono when SAP and/or Stereo is broadcast.

f OPTIONS Accesses options relating to the current activity or selection.

g OK Con� rms an entry or selection and displays the channel grid, when watching TV.

h ( Navigation buttons ) Navigates menus.

i INFO Displays program information, if available.

j ( Mute ) Mutes or restores volume.

k CH +/- ( CHANNEL +/ - ) Switches to the next or previous channel. When the TV menu is on, this functions as Page Up/Down.

l 0-9 ( Numeric buttons ) Selects a channel or setting.

m PICTURE ( Smart picture ) Launches the picture menu.

n SOUND ( Smart Sound ) Launches the sound menu.

o +/- ( Volume +/- ) Increases or decreases volume.

p BACK A/CH Returns to a previous screen.• Returns to the previously viewed • channel.

q BROWSE Switches between channel grid and program list.

r CC Displays closed captions settings.

EN

Dali_77_EN_2.indd 6 4/6/2010 11:14:32 AM

7

Switch channels Press • CH +/- on the remote control or P/CH +/- on the side of the TV. Enter a channel number using the • Numeric buttons . Press • OK to use the channel grid. Press • BACK A/CH on the remote control to return to the previous channel.

Note

When you use a favourite list, you can only •select those channels in the list (see ‘Select a favorite list’ on page 11 ) .

Switch channels with the channel grid The channel grid allows you to view all available channels in a grid format.

1 Press OK .

The channel grid appears. »

2 Press to browse the channel grid and preview a channel.

The channel content is displayed after »about two seconds.

3 Press OK to select a channel.

4 Use your TV This section helps you perform basic TV operations (see ‘Use more of your TV’ on page 9 ) .

Switch your TV on/off or to standby

To switch on

If the standby indicator is off, press • ( Power ) at the side of the TV. If the standby indicator is red, press • ( Standby-On ) on the remote control.

To switch to standby Press • ( Standby-On ) on the remote control.

The standby indicator switches to red. »

To switch off Press • ( Power ) at the side of the TV.

The standby indicator switches off. »

Tip

Though your TV consumes very little power •when in standby, energy continues to be consumed. When not in use for an extended period of time, disconnect the TV power cable from the power outlet.

Engl

ish

EN

Dali_77_EN_2.indd 7 4/6/2010 11:14:32 AM

8

Adjust TV volume

To increase or decrease volume

Press • +/- . To mute or unmute sound

Press • to mute the sound. Press • again to restore the sound.

Watch connected devices

Note

Switch on the device before selecting it as a •source on the TV.

Use the source button

1 Press SOURCE .

The source list appears. »

2 Press to select a device. 3 Press OK to con� rm your choice.

The TV switches to the selected »device.

EN

Dali_77_EN_2.indd 8 4/6/2010 11:14:32 AM

9

Remove devices from the home menu If a device is no longer connected to the TV, remove it from the home menu. 1 Press MENU . 2 Press to select a device to remove. 3 Press OPTIONS .

The » [Remove device] list appears. 4 Press OK , then select [Remove] to

remove the device. The selected device is removed from »the home menu.

Change picture and sound settings Change picture and sound settings to suit your preferences. You can apply pre-de� ned settings or change settings manually.

Use smart picture Use smart picture to apply pre-de� ned picture settings. 1 Press PICTURE .

The » [Smart picture] menu appears. 2 Press to select from the following

smart picture settings: • [Personal] : Lists customized picture settings. • [Sports] : Applies rich and dynamic settings. • [Standard] : Adjusts picture settings to suit most environments and types of video. • [Movie] : Applies settings for movie viewing. • [Game] : Applies settings for games. • [Energy saving] : Applies low-energy settings.

3 Press OK to con� rm your choice. The selected smart picture setting is »applied.

5 Use more of your TV

Access TV menus Menus help you to install channels, change picture and sound settings and access other features. 1 Press MENU .

The menu screen appears. »

2 Press to select and navigate

through one of the following menus. • [Watch TV] : Switches back to the antenna source if another source is selected. • [Add new device] : Adds new devices to the home menu. • [Setup] : Accesses menus to change picture, sound and other settings.

3 Press OK to con� rm your choice. 4 Press MENU to exit.

Tip

After selecting • [Add new device] , follow the on-screen instructions to select the correct device and connector.

Add new deviceWatch TV Setup

Engl

ish

EN

Dali_77_EN_2.indd 9 4/6/2010 11:14:32 AM

10

Change picture format 1 Press FORMAT .

A picture format bar appears. »

2 Press to select a picture format. The selected picture format is activated. »

3 Press OK to con� rm your choice.

Summary of picture formats The following picture settings can be con� gured.

Note

Depending on the format of the picture •source, some picture settings are not available.

[Super zoom] : (Not for HD and PC mode.) Removes the black bars on the side of 4:3 broadcasts. There is minimal distortion.

[4:3] : Shows the classic 4:3 format.

[Subtitle zoom] : Displays 4:3 pictures over the full area of the screen, with sub-titles visible. Part of the top of the picture is clipped off.

[Movie expand 14:9] : (Not for HD and PC mode.) Scales 4:3 format to 14:9.

[Movie expand 16:9] : (Not for HD and PC mode.) Scales 4:3 format to 16:9.

[Wide screen] : Scales 4:3 format to 16:9.

[Unscaled] : For HD and PC mode only, and in selected models only. Allows maximum sharpness. Some distortion may be present due to the broadcaster’s systems. Set your PC resolution to wide screen mode for best results.

Manually adjust picture settings 1 Press MENU . 2 Press to select [Setup] >

[Picture] . The » [Picture] menu appears.

3 Press to select from the following settings and adjust: • [Smart picture] : Accesses pre-de� ned smart picture settings. • [Backlight] : Adjusts the backlight. • [Contrast] : Adjusts the intensity of bright areas, keeping dark areas unchanged. • [Brightness] : Adjusts the intensity and details of dark areas. • [Color] : Adjusts color saturation. • [Tint] : Adjusts the color balance in an image. • [Sharpness] : Adjusts sharpness in the image. • [Noise reduction] : Filters and reduces noise in an image. • [Color temperature] : Introduces more orange tones ( [Warm] ) or blue tones ( [Cool] ). • [Dig.CrystalClear] : Adjusts picture quality to optimal contrast, color and sharpness.

• [Dynamic contrast] : Enhances contrast. • [Dynamic backlight] : Adjusts brightness of the TV backlight to match lighting conditions. • [Color enhancement] : Makes colors more vivid and improves the details in bright colors. You can switch this feature on or off.

• [PC mode] : Adjusts picture settings when a PC is connected to the TV. • [Picture format] : Changes the picture format. • [Horizontal shift] : Adjusts the picture horizontally for PC-VGA or HD input. • [Vertical shift] : Adjusts the picture vertically for PC-VGA or HD input.

EN

Dali_77_EN_2.indd 10 4/6/2010 11:14:32 AM

11

• [Surround] : Enables spatial sound. • [Auto volume] : Automatically reduces sudden volume changes, for example, when switching channels. • [Delta volume] : Levels out volume differences between channels or connected devices. Switch to the connected device before you change the delta volume.

Create and use list of favorite channels You can create a list of your preferred TV channels so that you can � nd those channels easily.

Select a favorite list 1 When watching TV, press OK to display

the channel grid. 2 Press OPTIONS .

The channel options menu appears. »

3 Press to select [Select list] , then press OK to enter.

The channel list options appear. »

4 Select [Favorite] , then press OK . Only channels in the favorite list »appear in the channel grid.

Note

The favorite channel grid is empty until you •add channels into the favorite lists.

Add a channel to a favorite list 1 When watching TV, press OK .


2 Press to select a channel to add to a favorite list.

3 Press OPTIONS . The channel options menu appears. »

Use smart sound Use smart sound to apply pre-de� ned sound settings. 1 Press SOUND .

The » [Smart sound] menu appears.

2 Press to select a smart sound setting:

• [Standard] : Adjusts sound settings to suit most environments and types of audio. • [News] : Applies settings for spoken audio, such as news. • [Movie] : Applies settings for movies. • [Personal] : Applies the settings that were customized in the sound menu.

3 Press OK to con� rm your choice. The selected smart sound setting is »applied.

Manually adjust sound settings 1 Press MENU . 2 Press to select [Setup] > [Sound] .

The » [Sound] menu appears.

3 Press to select and adjust: • [Smart sound] : Accesses pre-de� ned smart sound settings. • [Bass] : Adjusts the bass level. • [Treble] : Adjusts the treble level. • [Volume] : Adjusts the volume. • [Balance] : Adjusts the balance of the right and left speakers. • [SAP] : Selects a second broadcast audio language. • [Mono/Stereo] : Selects mono or stereo if stereo broadcast is available. • [TV speakers] : Sets the TV speakers on or off, or outputs sound to an EasyLink-compliant device. Easylink must be activated in the preferences menu.

Engl

ish

EN

Dali_77_EN_2.indd 11 4/6/2010 11:14:33 AM

12

Note

To disable the clock, repeat the above •procedure.

Use timers You can set timers to switch the TV to standby at a speci� ed time.

Tip

Set the TV clock before you use timers. •

Automatically switch the TV to standby (sleep timer) Sleep timer switches the TV to standby after a pre-de� ned period of time.

Tip

You can switch off your TV earlier or reset the •sleep timer during the countdown.

1 Press MENU . 2 Press to select [Setup] >

[Features] > [Sleep timer] . The » [Sleep timer] menu appears.

3 Press to set the sleep time. The sleep timer can be up to 180 »minutes in steps of � ve minutes. If set to zero, the sleep timer is switched off.

4 Press OK to switch on the sleep timer. The TV switches to standby after the »speci� ed time.

4 Select [Mark as favorite] , then press OK . The channel is added to the favorite »list.

Note

All favorite channels are marked by an asterisk •in the channel grid.

Remove a channel from a favorite list 1 When watching TV, press OK .


2 Press to select a channel to remove.

3 Press OPTIONS . 4 Select [Unmark as fav.] , then press OK .

The channel is removed. »

Use the TV clock You can display the TV clock. (only available in RF)

Set the TV clock 1 Press MENU . 2 Select [Setup] > [Features] > [Clock]

The » [Clock] menu appears.

3 Press or the Numeric buttons to enter time.

4 Select [Done] and press OK to con� rm. 5 Press MENU to exit.

Display the TV clock 1 When watching TV, press OPTIONS .

The TV option menu appears. »

2 Select [Clock] . 3 Press OK .

EN

Dali_77_EN_2.indd 12 4/6/2010 11:14:33 AM

13

Lock or unlock the TV Lock the TV to prevent access to all channels and connected devices. 1 Press MENU . 2 Press to select [Setup] >

[Features] > [TV lock] . You are prompted to enter your PIN »code.

3 Enter your code with the Numeric buttons .

The » [TV lock] menu appears.

4 Press to select [Lock] or [Unlock] . 5 Press OK to con� rm.

All channels and connected devices are »locked or unlocked.

6 Press MENU to exit.

Note

If you select • [Lock] , you have to enter your code every time you turn on your TV.

Lock or unlock one or more channels 1 When watching TV, press OK to display

the channel grid. 2 Press to select a channel to lock or

unlock. 3 Press OPTIONS . 4 Press to select [Lock channel] or

[Unlock channel] , then press OK . You are prompted to enter your PIN »code.

5 Enter your code and press OK . If the channel is locked, a lock icon »displayed.

6 Repeat the process to lock or unlock more channels.

Automatically switch the TV on (on timer) You can switch on the TV from standby to a speci� c channel at a speci� ed time. 1 Press MENU . 2 Press to select [Setup] >

[Features] > [On timer] . 3 Press to enter the [On timer] menu.

• [Activate] : Selects how often the TV is switched on. • [Time] : Sets the time to switch on the TV. • [Channel no.] : Selects the channel.


Tip

Select • [On timer] > [Activate] > [Off] to disable this feature.

Use TV locks You can prevent your children from watching certain programs or channels by locking the TV controls.

Set or change your PIN code 1 Press MENU . 2 Press to select [Setup] >

[Features] > [Set code] / [Change code] . The » [Set code] / [Change code] menu appears.

3 Enter your code using the Numeric buttons .

Follow the on-screen instructions to »create or change your PIN code.

Tip

If you forget your code, enter ‘8888’ to •override any existing codes.

Engl

ish

EN

Dali_77_EN_2.indd 13 4/6/2010 11:14:34 AM

14

View photos and play music from a USB storage device Use the USB connector to view photos or listen to music stored on a USB storage device.

Note

Your TV only supports USB � ash drives in •FAT/FAT32 format. It does not support other devices that can be connected to the USB port including but not limited to the following: portable storage devices such as external hard drives and mini hard drives, MP3 player, digital camera, phone, portable video player, portable multimedia player.

Connect a USB storage device and enter the content browser 1 Turn on the TV. 2 Connect the USB storage device to the

TV . 3 Press MENU .

The home menu appears. »

4 Press to select [Browse USB] . 5 Press OK to con� rm.

The USB content browser appears. »

Tip

Press • BROWSE to switch between thumbnail and � le browsing views.

Note

Switch the TV off and on again for the change •to take effect. If you access the locked channels, you are •prompted to enter your PIN code.

View closed captions (subtitles) The caption service displays transmitted closed caption text. The captioned text can be displayed permanently or only when the TV is muted.

Note

This television provides a display of television •closed captioning that conforms with the EIA-608 standard and in accordance with Sections 15.119 of the FCCrules. If you connect your set-top box via HDMI or •component video input, you cannot select closed caption through the TV. You can select closed caption through the set-top box only. The captions do not always use correct •spelling and grammar. Not all TV programs and product commercials •include closed caption information. Refer to your area TV program listings for the TV channels and times of closed caption shows. The captioned programs are usually noted in the TV listings with service marks such as ‘CC’.

1 Press MENU . 2 Select [Setup] > [Features] > [Closed

caption] . 3 Press to enter [Closed caption] . 4 Press to select your preference. 5 Press OK . 6 Press MENU to exit.

EN

Dali_77_EN_2.indd 14 4/6/2010 11:14:35 AM

15

Listen to music 1 In USB browser view, select [MUSIC] and

press to enter. 2 Press to select a music track or

album. 3 Press OK to play the selected music.

Button Function OK Pause, resume play or stop

playback. / Go to the previous or next

music.

Music settings When listening music, press OPTIONS to access one of the following music settings.

• [Start playback] / [Stop playback] : Starts or stops the music. • [Play mode] :

• [Play once] : Disables repeat play and plays a song once. • [Repeat] : Repeats a song. • [Shuf� e] : Plays songs randomly.

• [Show info] : Displays the � le name. • [TV speakers] : Sets the TV speakers on or off.

View a slide show with music You can view picture slide show with background music. 1 Select an album of songs. 2 Press OK . 3 Press BACK to return to USB content

browser. 4 Select an album of pictures. 5 Press OK to view photo. 6 Press OK again to start slide show.

View photos 1 In the USB browser, press to enter the

[Picture] folder. 2 Press to select a photo or a photo

album. 3 Press OK to view a full screen image of

the photo.

Tip

When in full screen mode, press • to move between photos.

View a slide show of your photos 1 When a full screen image of a photo is

displayed, press OK . A slide show begins from the selected »photo.

2 Press the following buttons to control the slide show:

• OK to pause the slide show. • to go back or move forward to the next image. • BACK to stop the slide show.

Change slide show settings 1 When viewing a slide show, press

OPTIONS . The slide show options menu appears. »

2 Press to select from the following settings and adjust:

• [Start slideshow] / [Stop slideshow] : Starts or stops a slide show. • [Slideshow transitions] : Displays a list of transition styles. • [Slideshow frequency] : Sets the amount of time that a picture is shown. • [Rotate image] : Rotates a picture. • [Show info] : Displays the picture name, date, size and next picture in the slide show.

3 Press OK to con� rm the setting change.

Engl

ish

EN

Dali_77_EN_2.indd 15 4/6/2010 11:14:35 AM

16

Update using a USB device Connect your USB device to the USB port at the side of your TV. 1 If the software update screen does not

appear automatically, select [Setup] > [Software update] > [Local updates] .

2 Press OK to update the TV software manually.

3 Follow the on-screen instructions to complete the update.

Note

The TV restarts after the software update is •complete.

Change TV preferences Use the preferences menu to customize your TV settings. 1 Press MENU . 2 Select [Setup] > [Installation] >

[Preferences] . • [Location] : Optimizes TV settings for your location - home or shop. • [Volume bar] : Displays the volume bar when you adjust the volume. • [EasyLink] : Enables one-touch play and one-touch standby between EasyLink-compliant devices. • [Pixel Plus Link] : Overrides the settings of connected devices and uses the settings of the TV. • [E-sticker] : For shop mode only. Sets the location of the e-sticker.


Disconnect a USB storage device

Caution

Follow this procedure to avoid damage to your •USB storage device.

1 Press BACK to exit the USB browser. 2 Wait for � ve seconds then disconnect the

USB storage device.

Update the TV software Philips continuously tries to improve its products and we recommend that you update the TV software when updates are available. Check www.philips.com/support for availability.

Check the current software version 1 Press MENU . 2 Select [Setup] > [Software update] >

[Current software] . The TV displays the current software »information.

Download the software 1 On your PC, open a web browser and go

to www.philips.com/support. 2 Download the latest software upgrade

� le to your PC. 3 Decompress the ZIP-� le. 4 Copy the � le to the root directory of the

USB device.

EN

Dali_77_EN_2.indd 16 4/6/2010 11:14:35 AM

17

Start a TV demo You can use demonstrations to better understand the features of your TV. Some demos are not available on certain models. Available demos are displayed in the menu list. 1 Press DEMO on the remote control. 2 Press to select a demo and press OK

to view it. 3 Press BACK to exit.

Reset the TV to factory settings You can restore the default picture and sound settings of your TV. The channel installation settings remain the same. 1 Press MENU . 2 Select [Setup] > [Installation] > [Factory

settings] . 3 Press to enter [Factory settings] . 4 Select [Reset] to start resetting. 5 Press OK . 6 Press MENU to exit.

Engl

ish

EN

Dali_77_EN_2.indd 17 4/6/2010 11:14:35 AM

18

Manually install channels This section describes how to search and store analog TV channels manually.

Select your system

Note

Skip this step if your system settings are •correct.


[Installation] > [Channel install.] > [Manual install] .

The » [Manual install] menu appears.

3 Press to select [Color system] , then press to enter.

4 Select your system, then press OK to con� rm.

5 Repeat the previous steps for [Sound system] .


Fine tune analog channels 1 Press MENU . 2 Press to select [Setup] >



3 Press to select [Fine-tune] , then press to enter.

4 Press to adjust frequency. 5 Press OK to con� rm. 6 Press MENU to exit.

6 Install channels The � rst time you setup your TV, you are prompted to select a menu language and to install TV and digital radio channels (if available). This chapter provides instructions on how to re-install and � ne tune channels.

Select TV tuner

1 Press MENU . 2 Select [Setup] > [Installation] >

[Channel install.] > [Tuner mode] 3 Press to select the source of TV

broadcast, then press OK to con� rm the selection.

4 Press to return to previous menu.

Note

If you are not sure what TV source to use, •select [Auto] .

Automatically install channels This section describes how to search and store channels automatically. 1 Press MENU . 2 Select [Setup] > [Installation] >

[Channel install.] > [Channel assistant] . 3 Press OK . 4 Follow the on-screen instructions to

install channels.

EN

Dali_77_EN_2.indd 18 4/6/2010 11:14:35 AM

19

Tip

The device name can be up to six characters •long. Press • [Aa] to change uppercase letter to lowercase letter and vice versa.

Rearrange channels After you install channels, you can rearrange the order in which they appear. 1 When watching TV, press OK to display

the channel grid. 2 Press OPTIONS .


3 Press to select [Reorder] , then press OK .

4 Select the channel to rearrange, then press OK .

The selected channel is highlighted. »

5 Press to move the highlighted channel to the desired location, then press OK .

6 Press OPTIONS . » [Done reordering] appears on the screen.

7 Press OK to con� rm. 8 Press BACK to exit the channel grid.

Skip channels 1 When watching TV, switch to the channel

you want to skip. 2 Press MENU . 3 Press to select [Setup] >



4 Press to select [Skip channel] , then press to enter.

5 Press to select [Skip] > [Yes] , then press OK to skip current channel.

The selected channel is skipped when »you press CH +/- on your remote control or view the channel grid.

6 Repeat the previous steps to skip more channels.

Tip

Use the • Numeric buttons on the remote control to access the skipped channel. To access the skipped channel, repeat steps •1-5 and select [No] to restore.

Rename channels You can rename channels. The name appears when you select the channel. 1 When watching TV, press OK to display

the channel grid. 2 Select the channel to rename. 3 Press OPTIONS .


4 Press to select [Rename channel] , then press OK .

A text input box appears. »

5 Press to select characters. 6 Press OK to con� rm each characters. 7 Select [Done] , then press OK to � nish

renaming channels.

Engl

ish

EN

Dali_77_EN_2.indd 19 4/6/2010 11:14:35 AM

20

a TV ANTENNA Signal input from an antenna, cable or satellite.

b AUDIO OUT

Analog audio output to home theaters and other audio systems.

c CVI 1 / CVI 2 ( Y Pb Pr and AUDIO L/R )

Analog audio and video input from analog or digital devices such as DVD players or game consoles.

TV ANTENNA

AUDIOOUT AUDIO

IN

7 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start.

Caution

Disconnect the mains cord before connecting •devices.

Note

Different types of connectors may be used to •connect a device to your TV, depending on availability and your needs.

Back connector

EN

Dali_77_EN_2.indd 20 4/6/2010 11:14:35 AM

21

Side connector

a AUDIO L/R

Audio input from analog devices connected to VIDEO .

d PC IN ( VGA / PC and AUDIO IN ) Audio and video input from a computer.

e HDMI 1 / HDMI 2

Digital audio and video input from high-de� nition digital devices such as Blu-ray players.

Connections via DVI or VGA require an additional audio cable .

f SERV. U For use by service personnel only.

VGA

PC AUDIO IN

VGA/PC

Engl

ish

EN

Dali_77_EN_2.indd 21 4/6/2010 11:14:36 AM

22

Connect a computer Before you connect a computer to the TV

Set the monitor refresh rate on your • computer to 60Hz. Press • FORMAT and change the TV picture format to [Unscaled] .

Connect a computer with one of the following connectors:

Note

Connections via DVI or VGA require an •additional audio cable.

• HDMI cable

• DVI-HDMI cable

DVI

PC AUDIO IN/ PC IN(AUDIO)

b VIDEO Composite video input from analog devices such as VCRs.

c S-VIDEO

S-Video (side) to be used with Audio L/R connectors for camcorder, game console, etc. When you use the S-Video (side) for video signals, do not use the Composite video (side) input for video signals.

d USB

Data input from USB storage devices.

EN

Dali_77_EN_2.indd 22 4/6/2010 11:14:36 AM

23

Use Philips EasyLink Your TV supports Philips EasyLink, which uses the HDMI CEC (Consumer Electronics Control) protocol. EasyLink-compliant devices that are connected through HDMI connectors can be controlled by a single remote control.

Note

The EasyLink-compliant device must be •switched on and selected as the source. Philips does not guarantee 100% •interoperability with all HDMI CEC devices.

EasyLink features One-touch play When you connect your TV to devices that support one-touch play, you can control your TV and the devices with one remote control. One-touch standby When you connect your TV to devices that support standby, you can use your TV remote control to put your TV and all connected HDMI devices in standby mode. System audio control When you connect your TV to HDMI CEC compliant devices, your TV can switch automatically to play audio from the connected device. To use one-touch audio, you must map the audio input from the connected device to your TV. You can use the remote control from the connected device to adjust the volume.

• HDMI cable and HDMI-DVI adaptor

• VGA cable

DVI


VGA


VGA

Engl

ish

EN

Dali_77_EN_2.indd 23 4/6/2010 11:14:36 AM

24

Use a Kensington lock There is a Kensington security slot at the back of the TV. Prevent theft by looping a Kensington lock between the slot and a permanent object, such as a heavy table.

Enable or disable EasyLink

Note

Do not enable Philips EasyLink if you do not •intend to use it.


[Installation] > [Preferences] > [EasyLink] .

3 Select [On] or [Off] .

Use one-touch play 1 After enabling EasyLink, press play on

your device. The TV automatically switches to the »correct source.

Use one-touch standby 1 Press ( Standby-On ) on the TV’s or

device’s remote control. The TV and all connected HDMI »devices switch to standby.

Set TV speakers to EasyLink mode When you play content from an EasyLink compliant home theater, the TV speakers are automatically muted. 1 Press MENU . 2 Press to select [Setup] > [Sound]

> [TV speakers] > [Auto EasyLink] . The TV speakers are turned off »automatically when content from an Easylink compliant system is detected.

3 Select [Setup] > [Sound] > [TV speakers] > [On] to disable system audio control and enable the TV speakers.

EN

Dali_77_EN_2.indd 24 4/6/2010 11:14:36 AM

25

Multimedia Supported storage device: USB (Only • FAT 16 or FAT 32 USB storage devices are supported) Supported multimedia � le formats:•

Images: JPEG• Audio: MP3•

Note

Multimedia � le names must not exceed 128 •characters.

Tuner/Reception/Transmission

Antenna input: 75ohm coaxial (IEC75)• TV system: NTSC, PAL-M, PAL-N• Video playback: NTSC, PAL•

Remote control Batteries: 2 x AAA (R03 type)•

Power Mains power: 220-240 V ~, 50-60 Hz• Standby power: < 1 W• Ambient temperature: 5 to 40 degrees • Celsius

8 Product information

Product information is subject to change without notice. For detailed product information, go to www.philips.com/support.

Supported display resolutions Computer formats (HDMI)

Resolution - refresh rate:• 640 x 480 - 60Hz• 800 x 600 - 60Hz• 1024 x 768 - 60Hz• 1280 x 1024 - 60Hz• 1360 x 768 - 60Hz• 1920 X 1080 - 60Hz•

Computer formats (VGA) Resolution - refresh rate:•

640 x 480 - 60Hz• 800 x 600 - 60Hz• 1024 x 768 - 60Hz• 1280 x 1024 - 60Hz• 1360 x 768 - 60Hz•

Video formats Resolution - refresh rate:•

480i - 60Hz• 480p - 60Hz• 576i - 50Hz• 576p - 50Hz• 720p - 50Hz, 60Hz• 1080i - 50Hz, 60Hz• 1080p - 24Hz, 25Hz, 30Hz, 50Hz, • 60Hz

Engl

ish

EN

Dali_77_EN_2.indd 25 4/6/2010 11:14:36 AM

26

Product speci� cation Design and speci� cations are subject to change without notice.

32PFL3605 Without TV stand•

Dimension (WxHxD): 795.6 x 508.3 • x 93 (mm) Weight: 8.3 kg•

With TV stand• Dimension (WxHxD): 795.6 x 556.2 • x 221.5 (mm) Weight: 9.9 kg•


Dimension (WxHxD): 795.6 x 508.3 • x 93 (mm) Weight: 8.3 kg•

With TV stand• Dimension (WxHxD): 795.6 x 556.2 • x 221.5 (mm) Weight: 9.9 kg•


Dimension (WxHxD): 1018.5 x • 635.7 x 83 (mm) Weight: 11.5 kg•

With TV stand• Dimension (WxHxD): 1018.5 x • 683.5 x 236.4 (mm) Weight: 13.5 kg•


Dimension (WxHxD): 1018.5 x • 635.7 x 83 (mm) Weight: 11.5 kg•

With TV stand• Dimension (WxHxD): 1018.5 x • 683.5 x 236.4 (mm) Weight: 13.5 kg•

Supported TV mounts To mount the TV, purchase a Philips TV mount or a VESA-compatible TV mount. To prevent damage to cables and connectors, be sure to leave a clearance of at least 2.2 inches or 5.5cm from the back of the TV.

Warning

Follow all instructions provided with the TV •mount. Koninklijke Philips Electronics N.V. bears no responsibility for improper TV mounting that results in accident, injury or damage.

TV screen size (inches)

Required pitch (mm)

Required mounting bolts

32 200 x 200 4 x M6 42 300 x 200 4 x M6

EN

Dali_77_EN_2.indd 26 4/6/2010 11:14:36 AM

27

Cannot remove ‘e-sticker’ banner displayed on the TV.

To remove the logos and images, set the •location of your TV to home. 1. Press MENU . 2. Select [Setup] > [Installation] > [Preferences] > [Location] . 3. Select [Home] , then press OK .

TV channel issues Previously installed channels do not appear in the channel list:

Check that the correct channel list is •selected.

Picture issues The TV is on, but there is no picture:

Check that the antenna is properly •connected to the TV. Check that the correct device is selected •as the TV source.

There is sound but no picture: Check that the picture settings are •correctly set.

There is poor TV reception from an antenna connection:

Check that the antenna is properly •connected to the TV. Loud speakers, unearthed audio devices, •neon lights, high buildings and other large objects can in� uence reception quality. If possible, try to improve the reception quality by changing the antenna direction or moving devices away from the TV. If reception on only one channel is poor, •� ne tune this channel.

There is poor picture quality from connected devices:

Check that the devices are connected •properly. Check that the picture settings are •correctly set.

9 Troubleshooting This section describes commonly encountered issues and accompanying solutions.

General TV issues The TV does not switch on:

Disconnect the power cable from the •power outlet. Wait for one minute then reconnect it. Check that the power cable is securely •connected.

The remote control is not working properly: Check that the remote control batteries •are correctly inserted according to the +/- orientation. Replace the remote control batteries if •they are � at or weak. Clean the remote control and TV sensor •lens.

The standby light on the TV blinks red: Disconnect the power cable from the •power outlet. Wait until the TV cools down before reconnecting the power cable. If the blinking reoccurs, contact Philips Consumer Care.

You forgot the code to unlock the TV lock feature

Enter ‘8888’. • The TV menu is in the wrong language.

Change the TV menu to your preferred • language .

When turning the TV on/off/to standby, you hear a creaking sound from the TV chassis:

No action is required. The creaking sound •is normal expansion and contraction of the TV as it cools and warms up. This does not impact performance.

Engl

ish

EN

Dali_77_EN_2.indd 27 4/6/2010 11:14:37 AM

28

If there are intermittent sound •disruptions, check that output settings from the HDMI device are correct. If you use an HDMI-to-DVI adapter •or HDMI to DVI cable, check that an additional audio cable is connected to AUDIO IN (mini-jack only).

Computer connection issues The computer display on the TV is not stable:

Check that your PC uses the supported •resolution and refresh rate. Set the TV picture format to unscaled. •

Contact us If you cannot resolve your problem, refer to the FAQs for this TV at www.philips.com/support.

If the problem remains unresolved, contact Philips Consumer Care in your country as listed in this user manual.

Warning

Do not attempt to repair the TV yourself. This •may cause severe injury, irreparable damage to your TV or void your warranty.

Note

Make a note of your TV model and serial •number before you contact Philips. These numbers are printed on the back of the TV and on the packaging.

The TV did not save your picture settings: Check that the TV location is set to the • home setting. This mode offers you the � exibility to change and save settings.

The picture does not � t the screen; it is too big or too small:

Try using a different picture format. • The picture position is incorrect:

Picture signals from some devices may •not � t the screen correctly. Check the signal output of the device.

Sound issues There is picture but no sound from the TV:

Note

If no audio signal is detected, the TV •automatically switches the audio output off — this does not indicate malfunction.

Check that all cables are properly •connected. Check that the volume is not set to 0. • Check that the sound is not muted. •

There is picture but sound quality is poor: Check that the sound settings are •correctly set.

There is picture but sound comes from one speaker only:

Verify that sound balance is set to the •center.

HDMI connection issues There are problems with HDMI devices:

Note that HDCP (High-bandwidth Digital •Content Protection) support can delay the time taken for a TV to display content from a HDMI device. If the TV does not recognize the HDMI •device and no picture is displayed, try switching the source from one device to another and back again.

EN

Dali_77_EN_2.indd 28 4/6/2010 11:14:37 AM

29

D default settings 17 demo 17 devices 8 devices

add to home menu 9 remove 9 watch 8

digital services disconnect USB 16 display

resolution 25 dispose 4

E EasyLink

disable 24 enable 24 one-touch play 24 one-touch standby 24 system audio control 24

end of life 4 environmental care 4 e-sticker 16

F factory settings 17 favorites list

create list 11 view list 11

� ne tune channels 18

H HDMI 28 , 20 home mode 16

I install channels

automatic 18 manual 18

10 Index

A analog

� ne-tune 18

B batteries 25 , 4 bracket for wall mount 26

C care 4 channel grid 7 channels

favorites list 11 � ne-tune 18 grid 7 install

automatic 18 manual 18

list 11 lock 13 , 13 rename 19 reorder/rearrange 19 skip channels 19 switch 7 troubleshooting 27 tune 18

child lock lock channels 13 lock connected devices 13 PIN code 13

clock display 12 , 12

closed captions 14 computer

connect 28 , 22 display resolution 25

connect PC 28 , 22

connectors HDMI 28 , 20 overview 20

Engl

ish

EN

Dali_77_EN_2.indd 29 4/6/2010 11:14:37 AM

30

R rearrange channels 19 reception 27 , 18 recycle 4 register product 5 remote control

batteries 25 , 4 overview 5 technical speci� cations 25

rename channels 19 reorder channels 19 resolution 25 restore default 17

S safety 3 screen care 4 settings

picture 10 sound 11

shop mode 16 skip channels 19 slideshow

view 15 with music 15

smart picture 9 smart settings 9 , 11 smart sound 11 software

version 16 sound settings 11 , 11 speci� cations 25 standby 7 switch

channels 7 on and off 7 source 8

T technical speci� cations 25 timer

on timer 12 , 13 sleep timer 12 standby 12

K Kensington lock 24

L language

troubleshoot 27 list

favorites list 11 location

home or shop 16 lock

Kensington lock 24 lock channels 13 lock connected devices 13 PIN code 13

M menu

main menu 9 MPEG artifact reduction 10 multimedia 25 music

USB 15 with slideshow 15

mute TV speakers 24

O on timer 13 , 12 one-touch play 24 one-touch standby 24

P PC

connect 28 resolution 25

picture format change 10 troubleshooting 27

picture settings 9 PIN code 13 pixel plus link 16 power 25 preferences 16 product speci� cations 25

EN

Dali_77_EN_2.indd 30 4/6/2010 11:14:37 AM

31

transmission 25 , 27 transporting 3 troubleshooting 27 TV lock

lock channels 13 lock connected devices 13 PIN code 13

TV overview 5

U USB

disconnect USB 16 listen to music 15 update software 16 view photos 15

V video format

technical speci� cations 25 volume

adjust 8 automatic leveling 11 delta 11 mute 8 , 24

W wall mount 3 , 26

Engl

ish

EN

Dali_77_EN_2.indd 31 4/6/2010 11:14:37 AM


philips



Documents

Register your product and get support at ... · compuertas de tiro (registros) ... Montaje en la pared o cielorraso - El aparato se debe montar en ... • When stand mounting the