Recommended Minimum Performance Standards for … · 3GPP2 C.S0011-C v2.0 CONTENTS v 1 3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power 2 Control Sets

3GPP2 C.S0011-C

Date: February 20, 2006

Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations

Release C, Version 2.0

COPYRIGHT

3GPP2 and its Organizational Partners claim copyright in this document and individual Organizational Partners may copyright and issue documents or standards publications in individual Organizational Partner's name based on this document. Requests for reproduction of this document should be directed to the 3GPP2 Secretariat at [email protected]. Requests to reproduce individual Organizational Partner's documents should be directed to that Organizational Partner. See www.3gpp2.org for more information.

Deleted: December 06

Deleted: 2005

Deleted: 0.91

Copyright © 2006 3GPP2

Formatted: Left

No text

3GPP2 C.S0011-C v2.0

CONTENTS

i

NORMATIVE REFERENCES ............................................................................................ xli 1

1 INTRODUCTION .......................................................................................................1-1 2

1.1 Scope..................................................................................................................1-1 3

1.2 Terms and Definitions.........................................................................................1-1 4

1.3 Test Modes........................................................................................................1-16 5

1.4 CDMA Equations ..............................................................................................1-17 6

1.4.1 Transmit Power of the Base Station.............................................................1-17 7

1.4.2 Received Signal Strength for Mobile Station Not in Handoff .........................1-18 8

1.4.2.1 Single-Path Case ...................................................................................1-18 9

1.4.2.2 Two-Path Case.......................................................................................1-20 10

1.4.2.3 Three-Path Case ....................................................................................1-21 11

1.4.3 Received Signal Strength for Mobile Station in Two-Way Handoff ................1-21 12

1.5 Tolerances ........................................................................................................1-22 13

1.5.1 CDMA System Parameter Tolerances...........................................................1-22 14

1.5.2 Measurement Tolerances.............................................................................1-22 15

1.6 Test Requirements for Mobile Stations Supporting Analog Operation ................1-22 16

1.6.1 Modulated Tone Frequency .........................................................................1-23 17

2 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE.........................2-1 18

2.1 Standard Radiation Test Site ..............................................................................2-1 19

2.2 Search Antenna ..................................................................................................2-1 20

2.3 Field-Strength Measurement...............................................................................2-2 21

2.4 Frequency Range of Measurements.....................................................................2-2 22

2.5 Test Ranges ........................................................................................................2-2 23

2.5.1 30-Meter Test Range .....................................................................................2-2 24

2.5.2 3-Meter Test Range .......................................................................................2-3 25

2.6 Radiated Signal Measurement Procedures ..........................................................2-3 26

3 CDMA RECEIVER MINIMUM STANDARDS...............................................................3-1 27

3.1 Frequency Coverage Requirements .....................................................................3-1 28

3.2 Acquisition Requirements ...................................................................................3-1 29

3.2.1 Idle Handoff Tests .........................................................................................3-1 30

3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel ........................3-1 31

3GPP2 C.S0011-C v2.0

CONTENTS

ii

3.2.1.1.1 Definition............................................................................................3-1 1

3.2.1.1.2 Method of Measurement......................................................................3-1 2

3.2.1.1.3 Minimum Standard.............................................................................3-3 3

3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel ............................... 3-4 4

3.2.1.2.1 Definition............................................................................................3-4 5



3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control 8

Channel .................................................................................................. 3-6 9

3.2.1.3.1 Definition............................................................................................3-6 10



3.2.1.4 Idle Handoff to Another Frequency .......................................................... 3-9 13

3.2.1.4.1 Definition............................................................................................3-9 14


3.2.1.4.3 Minimum Standard...........................................................................3-15 16

3.2.2 Soft Handoff Tests.......................................................................................3-15 17

3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff .... 3-15 18

3.2.2.1.1 Definition..........................................................................................3-15 19

3.2.2.1.2 Method of Measurement....................................................................3-15 20


3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft 22

Handoff ................................................................................................. 3-20 23

3.2.2.2.1 Definition..........................................................................................3-20 24



3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff ...................................... 3-23 27

3.2.2.3.1 Definition..........................................................................................3-23 28



3.2.3 Access and Access Probe Handoff Tests ......................................................3-26 31

3.2.3.1 Access Probe Handoff ............................................................................ 3-26 32

3GPP2 C.S0011-C v2.0

CONTENTS

iii

3.2.3.1.1 Definition ..........................................................................................3-26 1


3.2.3.1.3 Minimum Standard ...........................................................................3-29 3

3.2.3.2 Access Handoff ......................................................................................3-30 4

3.2.3.2.1 Definition ..........................................................................................3-30 5


3.2.3.2.3 Minimum Standard ...........................................................................3-32 7

3.2.4 Candidate Frequency Single Search ............................................................3-33 8

3.2.4.1 Definition ..............................................................................................3-33 9

3.2.4.2 Method of Measurement ........................................................................3-33 10

3.2.4.3 Minimum Standard ...............................................................................3-35 11

3.3 Forward Common Channel Demodulation Performance ....................................3-35 12

3.3.1 Demodulation of Non-Slotted Mode Paging Channel ....................................3-35 13

3.3.1.1 Definition ..............................................................................................3-36 14



3.3.2 Demodulation of Slotted Mode Paging Channel ...........................................3-37 17

3.3.2.1 Definition ..............................................................................................3-37 18



3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel..................3-39 21

3.3.3.1 Definition ..............................................................................................3-39 22



3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading 25

Channel ......................................................................................................3-40 26

3.3.4.1 Definition ..............................................................................................3-40 27



3.3.5 Demodulation of Forward Common Control Channel...................................3-42 30

3.3.5.1 Definition ..............................................................................................3-42 31

3GPP2 C.S0011-C v2.0

CONTENTS

iv

3.3.5.2 Method of Measurement........................................................................ 3-42 1

3.3.5.3 Minimum Standard ............................................................................... 3-43 2

3.3.6 Demodulation of Common Assignment Channel and Reception of 3

Common Power Control Channel ................................................................3-43 4

3.3.6.1 Definition .............................................................................................. 3-43 5



3.3.7 Demodulation of Forward Packet Data Control Channel in Additive White 8

Gaussian Noise ...........................................................................................3-45 9

3.3.7.1 Definition .............................................................................................. 3-45 10



3.3.8 Demodulation of Forward Packet Data Control Channel in Soft and 13

Softer Handoff.............................................................................................3-48 14

3.3.8.1 Definition .............................................................................................. 3-48 15



3.4 Forward Traffic Channel Demodulation Performance ........................................3-54 18

3.4.1 Demodulation of Forward Fundamental Channel in Additive White 19

Gaussian Noise ...........................................................................................3-54 20

3.4.1.1 Definition .............................................................................................. 3-54 21



3.4.2 Demodulation of Forward Fundamental Channel in Multipath Fading 24

Channel ......................................................................................................3-55 25

3.4.2.1 Definition .............................................................................................. 3-55 26



3.4.3 Demodulation of Forward Fundamental Channel During Soft Handoff........3-58 29

3.4.3.1 Definition .............................................................................................. 3-58 30



3GPP2 C.S0011-C v2.0

CONTENTS

v

3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power 1

Control Sets During Soft Handoff ................................................................3-59 2

3.4.4.1 Definition ..............................................................................................3-59 3



3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power 6

Control Set..................................................................................................3-60 7

3.4.5.1 Definition ..............................................................................................3-60 8



3.4.6 Demodulation of Power Control Subchannel During Soft Handoff ...............3-62 11

3.4.6.1 Definition ..............................................................................................3-62 12



3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel 15

with Closed Loop Power Control (FPC_MODE = ‘000’) ..................................3-64 16

3.4.7.1 Definition ..............................................................................................3-64 17




with Closed Loop Power Control (FPC_MODE = ‘010’) ..................................3-66 21

3.4.8.1 Definition ..............................................................................................3-66 22




with Outer Loop Power Control and Closed Loop Power Control 26

(FPC_MODE = ‘000’, ‘001’ and ‘010’)............................................................3-67 27

3.4.9.1 Definition ..............................................................................................3-67 28




with Closed Loop Power Control (FPC_MODE = ‘000’) and Transmit 32

Diversity (OTD or STS).................................................................................3-69 33

3.4.10.1 Definition ..............................................................................................3-69 34

3GPP2 C.S0011-C v2.0

CONTENTS

vi





Diversity (OTD or STS) ................................................................................3-70 5

3.4.11.1 Definition .............................................................................................. 3-70 6



3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot 9

Channel Gating...........................................................................................3-72 10

3.4.12.1 Definition .............................................................................................. 3-72 11



3.4.13 Demodulation of Power Control Subchannel During Reverse 14

Fundamental Channel Gating.....................................................................3-73 15

3.4.13.1 Definition .............................................................................................. 3-73 16



3.4.14 Demodulation of Forward Packet Data Channel in Additive White 19

Gaussian Noise ...........................................................................................3-73 20

3.4.14.1 Definition .............................................................................................. 3-74 21



3.4.15 Demodulation of Forward Packet Data Channel in Multipath Fading 24

Channel with no Power Control...................................................................3-75 25

3.4.15.1 Definition .............................................................................................. 3-75 26



3.5 Receiver Performance .......................................................................................3-76 29

3.5.1 Receiver Sensitivity and Dynamic Range .....................................................3-76 30

3.5.1.1 Definition .............................................................................................. 3-76 31



3GPP2 C.S0011-C v2.0

CONTENTS

vii

3.5.2 Single Tone Desensitization.........................................................................3-77 1

3.5.2.1 Definition ..............................................................................................3-77 2



3.5.3 Intermodulation Spurious Response Attenuation ........................................3-80 5

3.5.3.1 Definition ..............................................................................................3-80 6



3.5.4 Adjacent Channel Selectivity .......................................................................3-84 9

3.5.4.1 Definition ..............................................................................................3-85 10



3.5.5 Receiver Blocking Characteristics................................................................3-87 13

3.5.5.1 Definition ..............................................................................................3-87 14



3.6 Limitations on Emissions..................................................................................3-89 17

3.6.1 Conducted Spurious Emissions...................................................................3-89 18

3.6.1.1 Definition ..............................................................................................3-89 19



3.6.2 Radiated Spurious Emissions......................................................................3-90 22

3.6.2.1 Definition ..............................................................................................3-90 23



3.7 Supervision.......................................................................................................3-92 26

3.7.1 Paging Channel or Forward Common Control Channel................................3-92 27

3.7.1.1 Definition ..............................................................................................3-92 28



3GPP2 C.S0011-C v2.0

CONTENTS

viii

3.7.2 Forward Traffic Channel with Power Control Subchannel on F-FCH or F-1

DCCH .........................................................................................................3-94 2

3.7.2.1 Definition .............................................................................................. 3-94 3



3.7.3 Forward Traffic Channel with Power Control Subchannel on CPCCH ..........3-97 6

3.7.3.1 Definition .............................................................................................. 3-97 7



3.8 Channel Quality Measurement Performance.....................................................3-99 10

3.8.1 Forward Link Channel Quality Measurement Accuracy Test .......................3-99 11

3.8.1.1 Definition .............................................................................................. 3-99 12


3.8.1.3 Minimum Standard ............................................................................. 3-100 14

4 CDMA TRANSMITTER MINIMUM STANDARDS ........................................................4-1 15

4.1 Frequency Accuracy ...........................................................................................4-1 16

4.1.1 Definition......................................................................................................4-1 17

4.1.2 Method of Measurement ...............................................................................4-1 18

4.1.3 Minimum Standard.......................................................................................4-1 19

4.2 Handoff ..............................................................................................................4-2 20

4.2.1 CDMA to CDMA Hard Handoff ......................................................................4-2 21

4.2.1.1 Definition ................................................................................................ 4-2 22

4.2.1.2 Method of Measurement.......................................................................... 4-2 23

4.2.1.3 Minimum Standard ................................................................................. 4-3 24

4.2.2 Transmit Power after Hard Handoff...............................................................4-3 25

4.2.2.1 Definition ................................................................................................ 4-3 26

4.2.2.2 Method of Measurement.......................................................................... 4-5 27

4.2.2.3 Minimum Standard ................................................................................. 4-7 28

4.3 Modulation Requirements...................................................................................4-8 29

4.3.1 Time Reference .............................................................................................4-8 30

4.3.1.1 Definition ................................................................................................ 4-8 31

3GPP2 C.S0011-C v2.0

CONTENTS

ix

4.3.1.2 Method of Measurement ..........................................................................4-9 1


4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance ..............................4-10 3

4.3.2.1 Definition ..............................................................................................4-10 4



4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance.............................4-11 7

4.3.3.1 Definition ..............................................................................................4-11 8



4.3.4 Waveform Quality and Frequency Accuracy.................................................4-11 11

4.3.4.1 Definition ..............................................................................................4-11 12



4.3.5 Code Domain Power ....................................................................................4-14 15

4.3.5.1 Definition ..............................................................................................4-14 16



4.4 RF Output Power Requirements........................................................................4-15 19

4.4.1 Range of Open Loop Output Power..............................................................4-15 20

4.4.1.1 Definition ..............................................................................................4-15 21


4.4.1.2.1 Access Channel .................................................................................4-16 23

4.4.1.2.2 Enhanced Access Channel ................................................................4-17 24


4.4.2 Time Response of Open Loop Power Control ................................................4-23 26

4.4.2.1 Definition ..............................................................................................4-23 27



4.4.3 Access Probe Output Power.........................................................................4-26 30

4.4.3.1 Definition ..............................................................................................4-26 31

3GPP2 C.S0011-C v2.0

CONTENTS

x


4.4.3.2.1 Access Channel Probe.......................................................................4-26 2

4.4.3.2.2 Enhanced Access Channel Probe ......................................................4-27 3


4.4.4 Range of Closed Loop Power Control ...........................................................4-28 5

4.4.4.1 Definition .............................................................................................. 4-28 6



4.4.5 Maximum RF Output Power........................................................................4-32 9

4.4.5.1 Definition .............................................................................................. 4-32 10



4.4.6 Minimum Controlled Output Power.............................................................4-40 13

4.4.6.1 Definition .............................................................................................. 4-40 14



4.4.7 Standby Output Power and Gated Output Power ........................................4-41 17

4.4.7.1 Definition .............................................................................................. 4-41 18



4.4.8 Power Up Function Output Power ...............................................................4-44 21

4.4.8.1 Definition .............................................................................................. 4-44 22



4.4.9 Code Channel to Reverse Pilot Channel Output Power Accuracy .................4-46 25

4.4.9.1 Definition .............................................................................................. 4-46 26


4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel 28

Header, Enhanced Access Channel Data, and Reverse Common 29

Control Channel Data .......................................................................4-46 30

4.4.9.2.2 Code Channel Output Power for the Reverse Traffic Channel ............4-48 31

3GPP2 C.S0011-C v2.0

CONTENTS

xi

4.4.9.2.3 Code Channel Output Power for the Reverse Channel Quality 1

Indicator Channel and the Reverse Acknowledgement Channel .........4-50 2


4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity...................................4-53 4

4.4.10.1 Definition ..............................................................................................4-53 5



4.4.11 Reverse Traffic Channel Output Power During Changes in Data Rate..........4-55 8

4.4.11.1 Definition ..............................................................................................4-55 9



4.5 Limitations on Emissions..................................................................................4-57 12

4.5.1 Conducted Spurious Emissions...................................................................4-57 13

4.5.1.1 Definition ..............................................................................................4-57 14



4.5.1.3.1 Spreading Rate 1...............................................................................4-62 17

4.5.1.3.2 Spreading Rate 3...............................................................................4-66 18

4.5.2 Radiated Spurious Emissions......................................................................4-67 19

4.5.3 Occupied Bandwidth...................................................................................4-67 20

4.5.3.1 Definition ..............................................................................................4-67 21



5 CDMA ENVIRONMENTAL REQUIREMENTS .............................................................5-1 24

5.1 Temperature and Power Supply Voltage ..............................................................5-1 25

5.1.1 Definition ......................................................................................................5-1 26

5.1.2 Method of Measurement................................................................................5-1 27

5.1.3 Minimum Standard .......................................................................................5-2 28

5.2 High Humidity ....................................................................................................5-2 29

5.2.1 Definition ......................................................................................................5-2 30

5.2.2 Method of Measurement................................................................................5-3 31

3GPP2 C.S0011-C v2.0

CONTENTS

xii


5.3 Vibration Stability ..............................................................................................5-3 2

5.3.1 Definition......................................................................................................5-3 3



5.4 Shock Stability ...................................................................................................5-3 6

5.4.1 Definition......................................................................................................5-3 7



6 CDMA STANDARD TEST CONDITIONS ....................................................................6-1 10

6.1 Standard Equipment ..........................................................................................6-1 11

6.1.1 Basic Equipment ..........................................................................................6-1 12

6.1.2 Associated Equipment ..................................................................................6-1 13

6.2 Standard Environmental Test Conditions ...........................................................6-1 14

6.3 Standard Conditions for the Primary Power Supply ............................................6-1 15

6.3.1 General.........................................................................................................6-1 16

6.3.2 Standard DC Test Voltage from Accumulator Batteries .................................6-1 17

6.3.3 Standard AC Voltage and Frequency.............................................................6-2 18

6.4 Standard Test Equipment...................................................................................6-2 19

6.4.1 Standard Channel Simulator ........................................................................6-2 20

6.4.1.1 Channel Model Parameters ..................................................................... 6-2 21

6.4.1.2 Channel Model Parameter Conditions and Tolerances ............................. 6-4 22

6.4.1.3 Channel Simulator Configurations .......................................................... 6-5 23

6.4.2 Waveform Quality Measurement Equipment .................................................6-5 24

6.4.2.1 Rho Meter for Radio Configuration 1 and 2 ............................................. 6-5 25

6.4.2.2 Rho Meter for Radio Configuration 3 through 9 ....................................... 6-7 26

6.4.2.2.1 The Ideal Composite Reference Signal .................................................6-7 27

6.4.2.2.2 The Transmitter Signal-Under-Test .....................................................6-8 28

6.4.2.2.3 Active Code-Channel Identification, Symbol Detection and 29

Parameter Estimation .........................................................................6-9 30

6.4.2.2.4 Rho (ρ) ..............................................................................................6-10 31

3GPP2 C.S0011-C v2.0

CONTENTS

xiii

6.4.2.2.5 Code-domain Power (CDP).................................................................6-11 1

6.4.2.2.6 Power in Undesired Channels............................................................6-12 2

6.4.2.2.7 Code Domain Time Offsets and Phase Offsets Relative to Reverse 3

Pilot Channel.....................................................................................6-12 4

6.4.2.3 Code Domain Measurement Equipment Accuracy .................................6-13 5

6.4.3 Base Station Equipment..............................................................................6-13 6

6.4.3.1 Transmitter Equipment .........................................................................6-13 7

6.4.3.2 Receiver Equipment...............................................................................6-15 8

6.4.3.3 Protocol Support....................................................................................6-15 9

6.4.3.4 Timing Signals.......................................................................................6-15 10

6.4.4 AWGN Generator.........................................................................................6-16 11

6.4.5 CW Generator .............................................................................................6-17 12

6.4.6 Spectrum Analyzer ......................................................................................6-17 13

6.4.7 Average Power Meter ...................................................................................6-18 14

6.4.8 Phase Transient Measuring Equipment .......................................................6-19 15

6.5 Functional System Set-ups ...............................................................................6-19 16

6.5.1 Functional Block Diagrams .........................................................................6-19 17

6.5.2 General Comments......................................................................................6-21 18

6.6 Confidence Limits .............................................................................................6-32 19

6.6.1 Confidence Level of Error Rate ....................................................................6-32 20

6.6.2 Confidence on Power Measurement During Fading......................................6-36 21

6.6.3 Confidence Level of Detection Time .............................................................6-39 22

ANNEX A: SELECTED PERFORMANCE REQUIREMENTS TABLES.............................. A-1 23

A.1 Forward Common Channel Performance Tables ................................................. A-1 24

A.1.1 Non-Slotted Mode Paging Channel Performance Requirements......................A-1 25

A.1.1.1 Method of Measurement Test Parameters .............................................A-1 26

A.1.1.2 Minimum Standards Requirements ......................................................A-1 27

A.1.2 Slotted Mode Paging Channel Performance Requirements .............................A-2 28



A.1.3 Forward Broadcast Control Channel Performance Requirements in 31

AWGN Channel .............................................................................................A-6 32

3GPP2 C.S0011-C v2.0

CONTENTS

xiv



A.1.4 Forward Broadcast Control Channel Performance Requirements in 3

Multipath Fading Channel ..........................................................................A-11 4

A.1.4.1 Method of Measurement Test Parameters ...........................................A-12 5

A.1.4.2 Minimum Standards Requirements ....................................................A-32 6

A.1.5 Forward Common Control Channel Performance Requirements ..................A-41 7



A.1.6 Common Assignment Channel and Common Power Control Channel 10

Performance Requirements .........................................................................A-47 11



A.2 Forward Traffic Channel Demodulation Performance Tables .............................A-51 14

A.2.1 Forward Traffic Channel Performance Requirements in AWGN....................A-51 15



A.2.2 Forward Traffic Channel Performance Requirements in Multipath Fading 18

Channel ......................................................................................................A-91 19


A.2.2.2 Minimum Standards Requirements ..................................................A-101 21

A.2.3 Forward Fundamental Channel Performance Requirements During Soft 22

Handoff.....................................................................................................A-105 23

A.2.3.1 Method of Measurement Test Parameters .........................................A-106 24


A.2.4 Power Control Bit Performance Requirements for Channels Belonging to 26

Different Power Control Sets During Soft Handoff .....................................A-106 27



A.2.5 Power Control Bit Performance Requirements for Channels Belonging to 30

the Same Power Control Set......................................................................A-107 31



3GPP2 C.S0011-C v2.0

CONTENTS

xv

A.2.6 Power Control Subchannel Performance Requirements During Soft 1

Handoff .....................................................................................................A-108 2




Channel with Closed Loop Power Control (FPC_MODE = ‘000’) ..................A-109 6




Channel with Closed Loop Power Control (FPC_MODE = ‘010’) ..................A-120 10




Channel with Outer Loop Power Control and Closed Loop Power Control 14

(FPC_MODE = ‘000’, ‘001’ and ‘010’)..........................................................A-135 15





Diversity (OTD or STS)...............................................................................A-141 20





Diversity (OTD or STS)...............................................................................A-151 25



A.2.12 Power Control Subchannel Performance Requirements During Reverse 28

Pilot Channel Gating .................................................................................A-156 29




Fundamental Channel Gating ...................................................................A-157 33


3GPP2 C.S0011-C v2.0

CONTENTS

xvi


A.2.14 Forward Packet Data Channel Performance Requirements in Additive 2

White Gaussian Noise ...............................................................................A-159 3



A.2.15 Forward Packet Data Channel Performance Requirements in Multipath 6

Fading Channel with no Power Control .....................................................A-199 7



10

3GPP2 C.S0011-C v2.0

FIGURES

xvii

Figure 3.2.1.1.2-1. Idle Handoff in Non-Slotted Mode (Test 1).......................................... 3-3 1

Figure 3.2.1.1.2-2. Idle Handoff in Non-Slotted Mode (Test 2).......................................... 3-3 2

Figure 3.2.1.2.2-1. Slotted Mode Idle Handoff ................................................................. 3-6 3

Figure 3.2.1.3.2-1. Slotted Mode Idle Handoff ................................................................. 3-8 4

Figure 3.2.1.4.2-1. Idle Handoff to Another Frequency (Test 1)...................................... 3-14 5

Figure 3.2.1.4.2-2. Idle Handoff to Another Frequency (Test 2)...................................... 3-14 6

Figure 3.2.2.1.2-1. Neighbor Set Pilot Detection ............................................................ 3-18 7

Figure 3.2.2.1.2-2. Neighbor Set Pilot Incorrect Detection ............................................. 3-19 8

Figure 3.2.2.2.2-1. Candidate Set Pilot Detection (Test 1) .............................................. 3-22 9

Figure 3.2.2.2.2-2. Candidate Set Pilot Incorrect Detection (Test 2) ............................... 3-22 10

Figure 3.2.2.3.2-1. Active Set Pilot Loss Detection (Test 2) ............................................ 3-26 11

Figure 3.2.3.1.2-1. Access Probe Handoff ...................................................................... 3-29 12

Figure 3.2.3.2.2-1. Access Handoff................................................................................ 3-32 13

Figure 3.3.8.2-1. Forward Packet Data Channel Demodulation in Softer and Soft 14

Handoff (Tests 1 and 2) ........................................................................................... 3-51 15

Figure 3.3.8.2-2. Forward Packet Data Channel Demodulation in Softer Handoff 16

(Test 3).................................................................................................................... 3-52 17

Figure 3.3.8-3. Forward Packet Data Channel Demodulation in Soft Handoff (Test 4).... 3-52 18

Figure 3.4.6.2-1. Demodulation of Power Control Subchannel During Soft Handoff....... 3-64 19

Figure 4.4.2.3-1. Upper and Lower Limits for Open Loop Power Control Step 20

Response for ΔPin = 20 dB ...................................................................................... 4-25 21

Figure 4.4.7.3-1. Transmission Envelope Mask (Average Gated-on Power Control 22

Group) .................................................................................................................... 4-44 23

Figure 6.4.1-1. Autocorrelation Coefficient of the Phase .................................................. 6-3 24

Figure 6.5.1-1. Functional Set-up for Traffic Channel Tests in Fading Channel............. 6-19 25

Figure 6.5.1-2. Functional Set-up for Traffic Channel Tests in Soft Handoff .................. 6-20 26

Figure 6.5.1-3. Functional Set-up for Searcher and Traffic Channel Tests in Soft 27

Handoff................................................................................................................... 6-20 28

Figure 6.5.1-4. Functional Set-up for Tests Without Fading .......................................... 6-21 29

Figure 6.5.1-5. Functional Set-up for Tests With Transmit Diversity ............................ 6-21 30

Figure 6.6.1-1. Ratio (Measured/Specified) Bound as a Function of Number of 31

Errors (k) for 95% Confidence ................................................................................. 6-34 32

3GPP2 C.S0011-C v2.0

FIGURES

xviii

Figure 6.6.1-2. Ratio (Measured/Specified) Bound as a Function of Number of 1

Errors (k) for 90% Confidence................................................................................. 6-34 2

Figure 6.6.1-3. Test Requirement for 95% Confidence of FER = 0.01............................. 6-35 3

Figure 6.6.1-4. Test Requirement for 95% Confidence of FER = 0.05............................. 6-35 4

Figure 6.6.1-5. Test Requirement for 95% Confidence of FER = 0.1............................... 6-36 5

Figure 6.6.1-6. Test Requirement for 90% Confidence of FER = 0.1............................... 6-36 6

7

3GPP2 C.S0011-C v2.0

TABLES

xix

Table 1.3-1. Test Configuration Combinations............................................................... 1-16 1

Table 3.2.1.1.2-1. Test Parameters for Idle Handoff in Non-Slotted Mode ........................ 3-2 2

Table 3.2.1.2.2-1. Test Parameters for Slotted Mode Idle Handoff .................................... 3-5 3

Table 3.2.1.3.2-1. Test Parameters for Slotted Mode Idle Handoff .................................... 3-8 4

Table 3.2.1.4.2-1. Test Parameters for Idle Handoff to Another Frequency..................... 3-13 5

Table 3.2.2.1.2-1. Test Parameters for Neighbor Set Pilot Detection (Test 1) .................. 3-17 6

Table 3.2.2.1.2-2. Test Parameters for Neighbor Set Pilot Detection (Test 2) .................. 3-17 7

Table 3.2.2.1.2-3. Test Parameters for Neighbor Set Pilot Incorrect Detection (Test 8

3) ............................................................................................................................ 3-18 9

Table 3.2.2.2.2-1. Test Parameters for Candidate Set Pilot Detection (Test 1) ................ 3-21 10

Table 3.2.2.2.2-2. Test Parameters for Candidate Set Pilot Incorrect Detection (Test 11

2) ............................................................................................................................ 3-21 12

Table 3.2.2.3.2-1. Test Parameters for Active Set Pilot Incorrect Loss Detection (Test 13

1) ............................................................................................................................ 3-25 14

Table 3.2.2.3.2-2. Test Parameters for Active Set Pilot Loss Detection (Test 2) ............... 3-25 15

Table 3.2.3.1.2-1. Test Parameters for Access Probe Handoff......................................... 3-28 16

Table 3.3.7.2-1. Test Parameters for Forward Packet Data Control Channel in 17

AWGN..................................................................................................................... 3-47 18

Table 3.3.7.3-1. Minimum Standards for Radio Configuration 10 Forward Packet 19

Data Control Channel Performance in AWGN.......................................................... 3-48 20

Table 3.3.8.2-1. Test Parameters for Forward Packet Data Channel Demodulation in 21

Soft and Softer Handoff........................................................................................... 3-51 22

Table 3.5.1.2-1. Test Parameters for Receiver Sensitivity and Dynamic Range............... 3-77 23

Table 3.5.2.2-1. Test Parameters for Single Tone Desensitization .................................. 3-79 24

Table 3.5.2.2-2. Minimum Effective Isotropic Radiated Power for Single Tone 25

Desensitization Test for Band Group 1900 ............................................................. 3-79 26

Table 3.5.2.2-3. Minimum Effective Radiated Power for Single Tone Desensitization 27

Test for Band Class 3.............................................................................................. 3-80 28

Table 3.5.3.2-1. Test Parameters for Band Groups 450 and 800 Intermodulation 29

Spurious Response Attenuation (Tests 1 and 2) ...................................................... 3-81 30

Table 3.5.3.2-2. Test Parameters for Band Class 1, 4, 8, 14 and 15 Intermodulation 31

Spurious Response Attenuation (Tests 1 and 2) ...................................................... 3-82 32

Table 3.5.3.2-3. Test Parameters for Band Class 6 Intermodulation Spurious 33

Response Attenuation (Tests 1 and 2) ..................................................................... 3-83 34

3GPP2 C.S0011-C v2.0

TABLES

xx





Table 3.5.4.2-1. Configuration for Interference Source .................................................. 3-86 5

Table 3.5.4.2-2. Test Parameters for Adjacent Channel Selectivity ................................ 3-86 6

Table 3.5.5.2-1. Test Parameters for Receiver Blocking Characteristics (In-Band) ......... 3-88 7

Table 3.5.5.2-2. Test Parameters for Receiver Blocking Characteristics (Out-Of-8

Band) ..................................................................................................................... 3-88 9

Table 3.6.2.3-1. Maximum Allowable Radiated Spurious Emissions for Band 10

Classes 0, 1, 7, 10, 14 and 15 ................................................................................ 3-91 11

Table 3.6.2.3-2. Maximum Allowable Radiated Spurious Emissions for Band 12

Classes 2, 3, 4, 5, 6, 8, 9, 11 and 12 ...................................................................... 3-91 13

Table 3.7.1.2-1. Test Parameters for Supervision of Paging Channel ............................. 3-93 14

Table 3.7.1.2-2. Test Parameters for Supervision of Forward Common Control 15

Channel.................................................................................................................. 3-94 16

Table 3.7.2.2-1. Test Parameters for Supervision of Forward Traffic Channel with 17

Power Control Subchannel on F-FCH or F-DCCH ................................................... 3-96 18


Power Control Subchannel on CPCCH .................................................................... 3-98 20

Table 4.2.1.2-1. Test Parameters for CDMA to CDMA Hard Handoff................................ 4-3 21



Table 4.3.1.2-1. Test Parameters for Time Reference ..................................................... 4-10 24

Table 4.4.1.2.1-1. Test Parameter of Îor for Range of Open Loop Output Power for 25

the Access Channel ................................................................................................ 4-17 26


the Spreading Rate 1 Enhanced Access Channel .................................................... 4-19 28


the Spreading Rate 3 Enhanced Access Channel .................................................... 4-20 30

Table 4.4.1.3-1. Minimum Standards for Range of Open Loop Output Power for the 31

Access Channel ...................................................................................................... 4-21 32


Spreading Rate 1 Enhanced Access Channel .......................................................... 4-22 34

3GPP2 C.S0011-C v2.0

TABLES

xxi


Spreading Rate 3 Enhanced Access Channel .......................................................... 4-23 2

Table 4.4.2.2-1. Test Parameters for Time Response of Open Loop Power Control ......... 4-24 3

Table 4.4.5.2-1. Test Parameters for Maximum RF Output Power with a Single 4

Traffic Code Channel, Spreading Rate 1 .................................................................. 4-36 5

Table 4.4.5.2-2. Test Parameters for Maximum RF Output Power with Multiple 6

Traffic Code Channels, Spreading Rate 1 ................................................................ 4-36 7

Table 4.4.5.2-3. Îor Values for Maximum RF Output Power with Multiple Traffic 8

Code Channels, Spreading Rate 1 ........................................................................... 4-37 9

Table 4.4.5.2-4. Test Parameters for Maximum RF Output Power with a Single 10

Traffic Code Channel, Spreading Rate 3 .................................................................. 4-38 11

Table 4.4.5.2-5. Test Parameters for Maximum RF Output Power with Multiple 12

Traffic Code Channels, Spreading Rate 3 ................................................................ 4-38 13

Table 4.4.5.3-1. Effective Radiated Power at Maximum Output Power ........................... 4-39 14

Table 4.4.5.3-2. Maximum Output Power Backoff Allowances ....................................... 4-40 15

Table 4.4.6.2-1. Test Parameters for Minimum Controlled Output Power ...................... 4-41 16

Table 4.4.7.2-1. Test Parameters for Standby Output Power and Gated Output 17

Power...................................................................................................................... 4-43 18

Table 4.4.9.3-1. Code Channel Accuracy Requirements for the Reverse 19

Fundamental Channel and Reverse Dedicated Control Channel.............................. 4-52 20

Table 4.4.9.3-2. Code Channel Accuracy Requirements for the (Convolutional 21

Coded) Reverse Supplemental Channel ................................................................... 4-52 22

Table 4.4.9.3-3. Code Channel Accuracy Requirements for the (Turbo Coded) 23

Reverse Supplemental Channel............................................................................... 4-52 24

Table 4.4.9.3-4. Code Channel Accuracy Requirements for the 9600 bps Reverse 25

Fundamental Channel (or 9600 bps Reverse Dedicated Control Channel) Being 26

Transmitted in Addition to the (Convolutional Coded) Reverse Supplemental 27

Channel .................................................................................................................. 4-53 28



Transmitted in Addition to the (Turbo Coded) Reverse Supplemental Channel ........ 4-53 31

Table 4.5.1.2-1. Test Parameters for Testing Spurious Emissions with a Single 32

Traffic Code Channel at Maximum RF Output Power .............................................. 4-60 33

Table 4.5.1.2-2. Test Parameters for Testing Spurious Emissions with Multiple 34

Traffic Code Channels at Maximum RF Output Power............................................. 4-60 35

Table 4.5.1.2-3. Îor Values for Testing Spurious Emissions with Multiple Traffic 36

Code Channels at Maximum RF Output Power ....................................................... 4-61 37

3GPP2 C.S0011-C v2.0

TABLES

xxii

Table 4.5.1.3.1-1. Band Groups 450 and 800 Transmitter Spurious Emission Limits 1

for Spreading Rate 1 ............................................................................................... 4-62 2

Table 4.5.1.3.1-2. Band Group 1900 Transmitter Spurious Emission Limits for 3

Spreading Rate 1 .................................................................................................... 4-63 4

Table 4.5.1.3.1-3. Band Class 3 Transmitter Spurious Emission Limits for 5

Spreading Rate 1 .................................................................................................... 4-63 6

Table 4.5.1.3.1-4. Additional Band Class 6 Transmitter Spurious Emission Limits 7


Table 4.5.1.3.1-5. Additional Band Class 11 and 12 Transmitter Spurious Emission 9

Limits for Spreading Rate 1 .................................................................................... 4-65 10

Table 4.5.1.3.2-1. Transmitter Spurious Emission Limits for Spreading Rate 3............. 4-66 11



Table 4.5.3.2-1. Test Parameters for Testing Occupied Bandwidth at Maximum RF 14

Output Power ......................................................................................................... 4-68 15

Table 5.1.1-1. Temperature Ranges................................................................................. 5-1 16

Table 6.4.1.3-1. Standard Channel Simulator Configurations ......................................... 6-5 17

Table 6.4.2.3-1. Accuracy of Code Domain Measurement Equipment............................ 6-13 18

Table A.1.1.1-1. Test Parameters for Non-Slotted Mode Paging Channel Performance 19

in AWGN................................................................................................................... A-1 20

Table A.1.1.2-1. Minimum Standards for Non-Slotted Mode Paging Channel 21

Performance in AWGN .............................................................................................. A-1 22

Table A.1.2.1-1. Test Parameters for Slotted Mode Paging Channel for Spreading 23

Rate 1 (Test 1) .......................................................................................................... A-2 24


Rate 1 (Test 2) .......................................................................................................... A-3 26


Rate 3 (Test 3) .......................................................................................................... A-4 28


Rate 3 (Test 4) .......................................................................................................... A-5 30

Table A.1.2.2-1. Minimum Standards for Slotted Mode Paging Channel Performance 31

for Spreading Rate 1 in AWGN (Test 1)...................................................................... A-5 32





3GPP2 C.S0011-C v2.0

TABLES

xxiii


for Spreading Rate 3 in AWGN (Test 4) ......................................................................A-6 2

Table A.1.3.1-1. Test Parameters for the Broadcast Control Channel in AWGN for 3

Spreading Rate 1 with Rate = 1/4 Code, No Transmit Diversity.................................A-7 4


Spreading Rate 1 with Rate = 1/2 Code, No Transmit Diversity.................................A-7 6


Spreading Rate 3 ......................................................................................................A-8 8

Table A.1.3.2-1. Minimum Standards for Broadcast Control Channel Performance in 9

AWGN for Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity .....................A-9 10


AWGN for Spreading Rate 1 with R = 1/2 Code, No Transmit Diversity ...................A-10 12


AWGN for Spreading Rate 3 ....................................................................................A-11 14

Table A.1.4.1-1. Test Parameters for Broadcast Control Channel for Spreading Rate 15

1 with R = 1/4 Code, No Transmit Diversity ............................................................A-12 16
















1 with R = 1/4 Code, Orthogonal Transmit Diversity...............................................A-20 32

Table A.1.4.1-10. Test Parameters for Broadcast Control Channel for Spreading 33

Rate 1 with R = 1/4 Code, Orthogonal Transmit Diversity.......................................A-21 34


Rate 1 with R = 1/2 Code, Orthogonal Transmit Diversity.......................................A-22 36

3GPP2 C.S0011-C v2.0

TABLES

xxiv


Rate 1 with R = 1/2 Code, Orthogonal Transmit Diversity ...................................... A-23 2


Rate 1 with R = 1/4 Code, Space Time Spreading ................................................... A-24 4








Rate 3..................................................................................................................... A-28 12


Rate 3..................................................................................................................... A-29 14


Rate 3..................................................................................................................... A-30 16


Rate 3..................................................................................................................... A-31 18

Table A.1.4.2-1. Minimum Standards for Broadcast Control Channel Performance 19

for Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity .............................. A-32 20








for Spreading Rate 3 ............................................................................................... A-40 28


for Spreading Rate 3 ............................................................................................... A-41 30

Table A.1.5.1-1. Test Parameters for the Forward Common Control Channel for 31

Spreading Rate 1 with Rate = 1/4 Mode, No Power Control, No Transmit 32

Diversity ................................................................................................................. A-42 33



Diversity ................................................................................................................. A-42 36

3GPP2 C.S0011-C v2.0

TABLES

xxv


Spreading Rate 3 with Rate = 1/4 Mode, No Power Control .....................................A-43 2



Table A.1.5.2-1. Minimum Standards for Forward Common Control Channel for 5


Diversity .................................................................................................................A-44 7



Diversity .................................................................................................................A-45 10





Table A.1.6.1-1. Test Parameters for the Common Assignment Channel for 15

Spreading Rate 1 with Rate = 1/4 mode in AWGN, No Transmit Diversity ...............A-48 16


Spreading Rate 1 with Rate = 1/2 mode in AWGN, No Transmit Diversity ...............A-49 18


Spreading Rate 3 in AWGN .....................................................................................A-49 20

Table A.1.6.2-1. Minimum Standards for Common Assignment Channel for 21

Spreading Rate 1 with Rate = 1/4 Mode in AWGN...................................................A-50 22

Table A.1.6.2-2 Minimum Standards for Common Assignment Channel for 23

Spreading Rate 1 with Rate = 1/2 Mode in AWGN...................................................A-50 24

Table A.1.6.2-3. Minimum Standards for Common Assignment Channel for 25

Spreading Rate 3 in AWGN .....................................................................................A-50 26

Table A.2.1.1-1. Test Parameters for Radio Configuration 1 Forward Fundamental 27

Channel in AWGN...................................................................................................A-51 28


Channel in AWGN...................................................................................................A-52 30


Channel in AWGN...................................................................................................A-52 32


Channel in AWGN...................................................................................................A-53 34


Channel or Forward Dedicated Control Channel with 100% Frame Activity in 36

AWGN.....................................................................................................................A-53 37

3GPP2 C.S0011-C v2.0

TABLES

xxvi



AWGN..................................................................................................................... A-54 3



AWGN..................................................................................................................... A-54 6



AWGN..................................................................................................................... A-55 9



AWGN..................................................................................................................... A-55 12



AWGN..................................................................................................................... A-56 15



AWGN..................................................................................................................... A-56 18



AWGN..................................................................................................................... A-57 21



AWGN..................................................................................................................... A-57 24



AWGN..................................................................................................................... A-58 27



AWGN..................................................................................................................... A-58 30



AWGN..................................................................................................................... A-59 33



AWGN..................................................................................................................... A-59 36



AWGN..................................................................................................................... A-60 39

3GPP2 C.S0011-C v2.0

TABLES

xxvii

Table A.2.1.1-19. Test Parameters for Radio Configuration 1 Forward Supplemental 1

Code Channel in AWGN ..........................................................................................A-60 2


Code Channel in AWGN ..........................................................................................A-61 4


Channel with 100% Frame Activity in AWGN with Convolutional Coding ................A-61 6


Channel with 100% Frame Activity in AWGN with Turbo Coding.............................A-62 8

























Table A.2.1.2-1. Minimum Standards for Radio Configuration 1 Forward 33

Fundamental Channel Performance in AWGN.........................................................A-69 34


Fundamental Channel Performance in AWGN.........................................................A-70 36

3GPP2 C.S0011-C v2.0

TABLES

xxviii


Fundamental Channel or Forward Dedicated Control Channel with 100% Frame 2

Activity Performance in AWGN................................................................................ A-71 3




















Supplemental Code Channel Performance in AWGN ............................................... A-77 23


Supplemental Code Channel Performance in AWGN ............................................... A-78 25


Supplemental Channel Performance with 100% Frame Activity in AWGN with 27

Convolutional Coding ............................................................................................. A-78 28



Turbo Coding.......................................................................................................... A-79 31



Convolutional Coding ............................................................................................. A-80 34



Turbo Coding.......................................................................................................... A-81 37

3GPP2 C.S0011-C v2.0

TABLES

xxix



Convolutional Coding..............................................................................................A-82 3



Turbo Coding ..........................................................................................................A-83 6






Turbo Coding ..........................................................................................................A-85 12






Turbo Coding ..........................................................................................................A-87 18






Turbo Coding ..........................................................................................................A-89 24


Supplemental Channel Performance in with 100% Frame Activity AWGN with 26




Turbo Coding ..........................................................................................................A-91 30

Table A.2.2.1-1. Test Parameters for Forward Fundamental Channel Radio 31

Configuration 1 in Fading Channel (Case 1) ............................................................A-92 32







3GPP2 C.S0011-C v2.0

TABLES

xxx


Configuration 1 in Fading Channel (Case 3)............................................................ A-96 2








Configuration 2 in Fading Channel (Case 6).......................................................... A-100 10

Table A.2.2.2-1. Minimum Standards for Fundamental Channel Performance in 11

Fading Channel (Case 1, Tests 1, 2 and 3) ............................................................ A-101 12


Fading Channel (Case 1, Test 4) ........................................................................... A-101 14


Fading Channel (Case 1, Test 5) ........................................................................... A-101 16


Fading Channel (Case 2)....................................................................................... A-102 18

Table A.2.2.2-5. Minimum Standards for Band Classes 0, 2, 3, 5, 7, 9, 10, 11 and 19

12 Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ........ A-102 20

Table A.2.2.2-6. Minimum Standards for Band Group 1900 Fundamental Channel 21

Performance in Fading Channel (Case 3, Test 12) ................................................. A-102 22

Table A.2.2.2-7. Recommended Minimum Standards for Band Group 450 and 800 23

Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ............. A-103 24

Table A.2.2.2-8. Recommended Minimum Standards for Band Group 1900 25

Fundamental Channel Performance in Fading Channel (Case 3, Test 12) ............. A-103 26

Table A.2.2.2-9. Minimum Standards for Fundamental Channel Radio 27

Configuration 2 Performance in Fading Channel (Case 4, Tests 13 and 14) .......... A-103 28


Configuration 2 Performance in Fading Channel (Case 5) ..................................... A-104 30


Configuration 2 Performance in Fading Channel (Case 6) ..................................... A-104 32


Fundamental Channel Radio Configuration 2 Performance in Fading Channel 34

(Case 6, Tests 20, 21, 22, and 23)......................................................................... A-105 35

3GPP2 C.S0011-C v2.0

TABLES

xxxi


Fundamental Channel Radio Configuration 2 Performance in Fading Channel 2

(Case 6, Tests 20, 21, 22, and 23) .........................................................................A-105 3


Channel During Soft Handoff ................................................................................A-106 5


Fundamental Channel Performance During Soft Handoff ......................................A-106 7

Table A.2.4.1-1. Test Parameters for Decision of Power Control Bit for Different 8

Power Control Sets................................................................................................A-107 9

Table A.2.5.1-1. Test Parameters for Decision of Power Control Bit for the Same 10

Power Control Set .................................................................................................A-108 11

Table A.2.6.1-1. Test Parameters for Demodulation of Power Control Subchannel 12

During Soft Handoff ..............................................................................................A-109 13

Table A.2.7.1-1. Test Parameters for Forward Power Control .......................................A-110 14


Channel or Forward Dedicated Control Channel with 100% Frame Activity...........A-111 16







Table A.2.7.1-6. Test Parameters for Radio Configuration 3 Forward Dedicated 23

Control Channel with 10% Frame Activity.............................................................A-113 24







Table A.2.7.2-1 Minimum Standards for Radio Configuration 3 Forward 31


Activity..................................................................................................................A-115 33



Activity..................................................................................................................A-116 36

3GPP2 C.S0011-C v2.0

TABLES

xxxii



Activity ................................................................................................................. A-117 3



Activity ................................................................................................................. A-118 6

Table A.2.7.2-5 Minimum Standards for Radio Configuration 3 Forward Dedicated 7

Control Channel with 10% Frame Activity ............................................................ A-119 8







Table A.2.8.1-1. Test Parameters for Forward Power Control....................................... A-121 15


Channel with 100% Frame Activity (Part 1 of 2) .................................................... A-122 17








Channel with 100% Frame Activity ....................................................................... A-126 25




Supplemental Channel with 100% Frame Activity (Part 1 of 2).............................. A-128 29









3GPP2 C.S0011-C v2.0

TABLES

xxxiii


Supplemental Channel with 100% Frame Activity (Part 2 of 2) ..............................A-133 2





Table A.2.9.1-1. Test Parameters for Slow Power Control in Fading Channel ...............A-136 7











Activity..................................................................................................................A-139 18



Activity..................................................................................................................A-139 21



Activity..................................................................................................................A-140 24



Activity..................................................................................................................A-140 27

Table A.2.10.1-1. Test Parameters for Forward Power Control .....................................A-141 28


Channel or Forward Dedicated Control Channel (100% Frame Activity) with 30

Orthogonal Transmit Diversity ..............................................................................A-142 31



Space Time Spreading...........................................................................................A-143 34



Orthogonal Transmit Diversity ..............................................................................A-143 37

3GPP2 C.S0011-C v2.0

TABLES

xxxiv



Space Time Spreading .......................................................................................... A-144 3


Control Channel (10% Frame Activity) with Orthogonal Transmit Diversity........... A-144 5


Control Channel (10% Frame Activity) with Space Time Spreading ....................... A-145 7






Fundamental Channel or Forward Dedicated Control Channel (100% Frame 13

Activity) with Orthogonal Transmit Diversity......................................................... A-146 14



Activity) with Space Time Spreading ..................................................................... A-147 17



Activity) with Orthogonal Transmit Diversity......................................................... A-148 20



Activity) with Space Time Spreading ..................................................................... A-149 23

Table A.2.10.2-5. Minimum Standards for Radio Configuration 3 Forward Dedicated 24








Table A.2.11.1-1. Test Parameters for Forward Power Control..................................... A-152 32


Channel (100% Frame Activity) with Orthogonal Transmit Diversity ..................... A-153 34


Channel (100% Frame Activity) with Space Time Spreading.................................. A-153 36

3GPP2 C.S0011-C v2.0

TABLES

xxxv


Channel (100% Frame Activity) with Orthogonal Transmit Diversity......................A-154 2


Channel (100% Frame Activity) with Space Time Spreading ..................................A-154 4


Supplemental Channel (100% Frame Activity) with Orthogonal Transmit 6

Diversity ...............................................................................................................A-155 7


Supplemental Channel (100% Frame Activity) with Space Time Spreading............A-155 9


Supplemental Channel (100% Frame Activity) with Orthogonal Transmit 11

Diversity ...............................................................................................................A-156 12


Supplemental Channel (100% Frame Activity) with Space Time Spreading............A-156 14


during Reverse Pilot Channel Gating.....................................................................A-157 16


during Reverse Fundamental Channel Gating.......................................................A-157 18

Table A.2.14.1-1. Test Parameters for Radio Configuration 10 Forward Packet Data 19

Channel in AWGN.................................................................................................A-159 20


Channel in AWGN.................................................................................................A-160 22


Channel in AWGN.................................................................................................A-161 24


Channel in AWGN.................................................................................................A-162 26


Channel in AWGN.................................................................................................A-163 28


Channel in AWGN.................................................................................................A-164 30


Channel in AWGN.................................................................................................A-165 32


Channel in AWGN.................................................................................................A-166 34


Channel in AWGN.................................................................................................A-167 36


Channel in AWGN.................................................................................................A-168 38

3GPP2 C.S0011-C v2.0

TABLES

xxxvi


Channel in AWGN................................................................................................. A-169 2


Channel in AWGN................................................................................................. A-170 4


Channel in AWGN................................................................................................. A-171 6


Channel in AWGN................................................................................................. A-172 8


Channel in AWGN................................................................................................. A-173 10


Channel in AWGN................................................................................................. A-174 12


Channel in AWGN................................................................................................. A-175 14


Channel in AWGN................................................................................................. A-176 16


Channel in AWGN................................................................................................. A-177 18


Channel in AWGN................................................................................................. A-178 20


Channel in AWGN................................................................................................. A-179 22


Channel in AWGN................................................................................................. A-180 24

Table A.2.14.2-1. Minimum Standards for Radio Configuration 10 Forward Packet 25

Data Channel Performance in AWGN.................................................................... A-181 26











3GPP2 C.S0011-C v2.0

TABLES

xxxvii


Data Channel Performance in AWGN ....................................................................A-187 2

























Table A.2.15.1-1 Test Parameters for Radio Configuration 10 Forward Packet Data 27

Channel in Fading (Part 1 of 6) .............................................................................A-199 28









3GPP2 C.S0011-C v2.0

TABLES

xxxviii


Channel in Fading (Part 6 of 6) ............................................................................. A-204 2

Table A.2.15.2-1 Minimum Standards for Radio Configuration 10 Forward Packet 3

Data Channel in Fading (Part 1 of 3)..................................................................... A-205 4





9

3GPP2 C.S0011-C v2.0

xxxix

NOTES 1

1. “Base station” refers to the functions performed on the land side, which are 2

typically distributed among a cell, a sector of a cell, and a mobile communications 3

switching center. 4

2. This Standard uses the following verbal forms: “Shall” and “shall not” identify 5

requirements to be followed strictly to conform to the standard and from which no 6

deviation is permitted. “Should” and “should not” indicate that one of several 7

possibilities is recommended as particularly suitable, without mentioning or 8

excluding others; that a certain course of action is preferred but not necessarily 9

required; or that (in the negative form) a certain possibility or course of action is 10

discouraged but not prohibited. “May” and “need not” indicate a course of action 11

permissible within the limits of the standard. “Can” and “cannot” are used for 12

statements of possibility and capability, whether material, physical, or causal. 13

3. Unless indicated otherwise, this document presents numbers in decimal form. 14

Binary numbers are distinguished in the text by the use of single quotation marks. 15

4. Those wishing to deploy systems compliant with this Standard should also be 16

compliant with Parts 15, 22, 24, and 27 of [2] and with the applicable rules and 17

regulations of local administrations. 18

5. The following operators define mathematical operations: 19

× indicates multiplication. 20

/ indicates division. 21

+ indicates addition. 22

- indicates subtraction. 23

* indicates complex conjugation. 24

∈ indicates a member of the set. 25

⎣x⎦ indicates the largest integer less than or equal to x: ⎣1.1⎦ = 1, ⎣1.0⎦ = 1. 26

|x| indicates the absolute value of x: |-17|=17, |17|=17. 27

6. All Radio Configuration 1 Eb/Nt requirements for Band Class 0 in this document 28

are based on measured data. For all other band classes, the radio configuration 29

Eb/Nt requirements in this document are based on simulated data with standard 30

margins of 1.3 dB for static and 1.5 dB for fading channel cases. Additional 31

Forward Fundamental Channel rate determination margins of 0.2, 0.3, and 0.4 dB 32

are added for the 1/2, 1/4, and 1/8 rate cases, respectively. An additional Forward 33

Supplemental Channel margin of 0.2 dB is added for Îor/Ioc equal to 6 and 8 dB 34

cases. Additional geometry dependent margins are added in Forward Packet Data 35

Channel test cases. Unless specified otherwise, the Forward Traffic Channel uses 36

20 ms long frame structures. 37

7. This Standard supports testing of mobile stations compliant with [4] and 38

subsequent revisions. 39

8. Tests in this revision reference the General Neighbor List Message, Universal 40

Neighbor List Message and the Universal Handoff Direction Message to maintain 41

3GPP2 C.S0011-C v2.0

xl

consistency with new tests that require the extended capability of these messages. 1

Where needed to test a P_REV six or lower mobile station, the Neighbor List 2

Message, Extended Neighbor List Message, and Extended Handoff Direction Message 3

may be used as specified in [6]. 4

9. For the test parameters tables, Îor is specified in terms of power spectral density in 5

a Spreading Rate 1 bandwidth. For testing applicable to Spreading Rate 3, the total 6

received power in a Spreading Rate 3 bandwidth is effectively 5 dB higher. 7

For the test parameters tables, Ec/Ior is specified in terms of the ratio in dB 8

between the energy accumulated over one PN chip period (Ec) to the total transmit 9

power spectral density in a Spreading Rate 1 bandwidth. For testing applicable to 10

Spreading Rate 3, Ec/Ior in a Spreading Rate 3 bandwidth is effectively 5 dB lower. 11

10. Many tests in this revision specify using the Paging Channel for general test setup 12

requirements. If the mobile station does not support the Paging Channel, then the 13

Broadcast Control Channel and Forward Common Control Channel shall be used in 14

lieu of the Paging Channel. 15

11. The specification applies only to Band Classes 0 (Band Subclasses 0 and 1), 1, 2, 16

(Band Subclasses 0, 1, and 2), 3, 4, 5 (Band Subclasses 0 through 7), 6, 7, 8, 9, 10 17

(Band Subclasses 0 through 4), 11 (Band Subclasses 0 through 5), 12 (Band 18

Subclasses 0 and 1), 14, and 15 as defined in [17]. Operation with other band 19

classes and band subclasses may noy be supported by this specification. 20

21

Formatted: Bullets and Numbering

Deleted: 10.

3GPP2 C.S0011-C v2.0

xli

NORMATIVE REFERENCES 1

The following standards contain provisions which, through reference in this text, constitute 2

provisions of this Standard. At the time of publication, the editions indicated were valid. All 3

standards are subject to revision, and parties to agreements based on this Standard are 4

encouraged to investigate the possibility of applying the most recent editions of the 5

standards indicated below. ANSI and TIA maintain registers of currently valid national 6

standards published by them. 7

8

General References

1. ANSI C63.4-2003, American National Standard for Methods of Measurement of Radio–Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz, 2003.

2. CFR Title 47, Code of Federal Regulations, October 2005.

9

10

3GPP2 Specifications and SDO Standards

3. 3GPP2:

Recommended Minimum Standards for 800-MHz Cellular Subscriber Units, 2000.

4.

3GPP2: C.S0002-D

Physical Layer Standard for cdma2000 Spread Spectrum Systems, 2004.

5.

3GPP2: C.S0004-D

Signaling Link Access Control (LAC) Standard for cdma2000 Spread Spectrum Systems, 2004.

6.

3GPP2: C.S0005-D

Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems, 2004.

7.

3GPP2: C.S0010-C

Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Base Stations, 2004.

8.

3GPP2: C.S0026-A

Test Data Service Option (TDSO) for cdma2000 Spread Spectrum Systems, 2004.

Deleted: 2003

Deleted: ARIB: STD-T64-C.S0002-D v1.0¶

CCSA:TIA: TIA/EIA-690TTA:TTC:

Deleted: ARIB: STD-T64-C.S0002-D v1.0¶

CCSA:TIA: TIA-2000.2-DTTA:TTC:

Deleted: ARIB: ¶CCSA:TIA: TIA-2000.4-DTTA:TTC:


Deleted: ARIB: ¶CCSA:TIA: TIA-97-FTTA:TTC:

Deleted: ARIB:CCSA:TIA: TIA-870-A¶TTA:TTC:

3GPP2 C.S0011-C v2.0

xlii

9.

3GPP2: C.S0025

Markov Service Option (MSO) for cdma2000 Spread Spectrum Systems, 2001.

10.

3GPP2: C.S0013-A

Loopback Service Options (LSO) for cdma2000 Spread Spectrum Systems, 2001.

11.

3GPP2: C.S0057

Band Class Specification for cdma2000 Spread Spectrum Systems, 2004.

12.

3GPP2: C.S0003-D

Medium Access Control (MAC) Standard for cdma2000 Spread Spectrum Systems, 2004.

Deleted: ARIB: STD-T64-C.S0025CCSA:TIA: TIA/EIA/IS-871TTA:TTC:

Deleted: ARIB: STD-T64-C.S0013-A¶CCSA:TIA: TIA/EIA-126-DTTA:TTC:

Deleted: ARIB: STD-T64-C.S0057-0 v1.0¶

CCSA:TIA: TIA-1030TTA:TTC:


3GPP2 C.S0011-C v2.0

1-1

1 INTRODUCTION 1

1.1 Scope 2

This Standard details definitions, methods of measurement, and minimum performance 3

characteristics for Code Division Multiple Access (CDMA) mobile stations. This Standard 4

shares the purpose of [4] (and subsequent revision thereof) by ensuring that a mobile 5

station can obtain service in any cellular system that meets the compatibility requirements 6

of [4]. 7

Compatibility, as used in connection with this Standard and [4], is understood to mean 8

that any mobile station is able to place and receive calls in any CDMA system. Conversely, 9

all CDMA systems are able to place and receive calls with any CDMA mobile station 10

supporting operation in the same band. 11

Test methods are recommended in this document; however, methods other than those 12

recommended may suffice for the same purpose. 13

The performance metrics in this Standard require a mobile station to provide a single 14

antenna connector for testing. Mobile stations having multiple antenna, such as for receive 15

diversity, shall provide a single antenna connector for testing. If a mobile station has more 16

than one antenna connector, only one connector shall be used for testing. Additional 17

requirements specifically for multiple antenna configurations, i.e. receive diversity, are for 18

future study. 19

1.2 Terms and Definitions 20

Access Attempt. A sequence of one or more access probe sequences on the Access 21

Channel or Enhanced Access Channel containing the same message. See also Access 22

Probe, Access Probe Sequence, and Enhanced Access Probe. 23

Access Channel. A Reverse CDMA Channel used by mobile stations for communicating to 24

the base station. The Access Channel is used for short signaling message exchanges, such 25

as call originations, responses to pages, and registrations. The Access Channel is a slotted 26

random access channel. 27

Access Probe. One Access Channel transmission consisting of a preamble and a message. 28

The transmission is an integer number of frames in length, and transmits one Access 29

Channel message. See also Access Probe Sequence and Access Attempt. 30

Access Probe Sequence. A sequence of one or more access probes on the Access Channel 31

or Enhanced Access Channel. The same Access Channel or Enhanced Access Channel 32

message is transmitted in every access probe of an access attempt. See also Access Probe, 33

Enhanced Access Probe, and Access Attempt. 34

ACLR. Adjacent Channel Leakage power Ratio. 35

Active Frame. A frame that contains data and therefore is enabled in terms of traffic 36

power. 37

3GPP2 C.S0011-C v2.0

1-2

Additional Preamble. A preamble sent after the last fractional preamble on the Reverse 1

Pilot Channel prior to transmitting on the Enhanced Access Channel or the Reverse 2

Common Control Channel. 3

Adjacent Channel Leakage power Ratio. The ratio of the on-channel transmit power to 4

the power measured in one of the adjacent channels. 5

AWGN. Additive White Gaussian Noise. 6

Bad Frame. A frame classified with insufficient frame quality, or, for Radio Configuration 1, 7

9600 bps primary traffic only frame with bit errors. See also Good Frame. 8

Band Class (BC). A set of frequency channels and a numbering scheme for these channels. 9

Band Group 450. A collection of band classes that use the 450 MHz simulation results for 10

fading conditions. This group consists of Band Class 5 (450 MHz Band) and Band Class 11 11

(400 MHz European PAMR Band). 12

Band Group 800. A collection of band classes that use the 800 MHz simulation results for 13

fading conditions. This group consists of Band Class 0 (800 MHz Band), Band Class 2 14

(TACS Band), Band Class 3 (JTACS Band), Band Class 7 (700 MHz Band), Band Class 9 15

(900 MHz Band), Band Class 10 (Secondary 800 MHz Band), and 12 (800 MHz European 16

PAMR Band). 17

Band Group 1900. A collection of band classes that use the 1900 MHz simulation results 18

for fading conditions. This group consists of Band Class 1 (1900 MHz Band), Band Class 4 19

(Korean PCS Band), Band Class 6 (2 GHz Band), Band Class 8 (1800 MHz Band), Band 20

Class 14 (US 1900 MHz Band), and Band Class 15 (AWS Band). 21

22

Base Station. A fixed station used for communicating with mobile stations. Depending 23

upon the context, the term base station may refer to a cell, a sector within a cell, an MSC, 24

or other part of the wireless system. 25

Basic Access Mode. A mode used on the Enhanced Access Channel where a mobile station 26

transmits an Enhanced Access Channel preamble and Enhanced Access data in a method 27

similar to that used on the Access Channel. 28

BCCH_Chip_Bit. Number of PN chips per Broadcast Control Channel bit. For Spreading 29

Rate 1, BCCH_Chip_Bit is equal to 64 x v where v equals 1 when the data rate is 19200 30

bps, v equals 2 when the data rate is 9600 bps, and v equals 4 when the data rate is 4800 31

bps. For Spreading Rate 3, BCCH_Chip_Bit is equal to 192 x v where v equals 1 when the 32

data rate is 19200 bps, v equals 2 when the data rate is 9600 bps, and v equals 4 when the 33

data rate is 4800 bps. 34

orc

IEBCCH . The ratio of the average transmit energy per PN chip for the Broadcast Control 35

Channel to the total transmit power spectral density. 36

bps. Bits per second. 37

Broadcast Control Channel (BCCH). A code channel in a Forward CDMA Channel used 38

for transmission of control information from a base station to a mobile station. 39

3GPP2 C.S0011-C v2.0

1-3

CACH_Chip_Bit. Number of PN chips per Common Assignment Channel bit. For Spreading 1

Rate 1, CACH_Chip_Bit is equal to 128 for 9600 bps. For Spreading Rate 3, 2

CACH_Chip_Bit is equal to 384 for 9600 bps. 3

orc

IECACH . The ratio of the average transmit energy per PN chip for the Forward Common 4

Assignment Channel to the total transmit power spectral density. 5

Candidate Frequency. The frequency for which the base station specifies a search set, 6

when searching on other frequencies while performing mobile-assisted handoffs. 7

CDMA. See Code Division Multiple Access. 8

CDMA Channel. The set of channels transmitted between the base station and the mobile 9

stations within a given CDMA frequency assignment. See also Forward CDMA Channel and 10

Reverse CDMA Channel. 11

CDMA Channel Number. An 11-bit number corresponding to the center of the CDMA 12

frequency assignment. 13

CDMA Frequency Assignment. A 1.23 MHz or a 3.69 MHz segment of spectrum. For Band 14

Class 0, the channel is centered on one of the 30 kHz channels. For band classes 1, 4, 6, 7, 15

8 and 9, the channel is centered on one of the 50 kHz channels. For band classes 2, 3, 10, 16

11 and 12, the channel is centered on one of the 25 kHz channels. For Band Class 5, the 17

channel is centered on one of the 20 or 25 kHz channels. 18

CDMA Preferred Set. The set of CDMA channel numbers in a CDMA system corresponding 19

to frequency assignments that a mobile station will normally search to acquire a CDMA 20

Pilot Channel. 21

Chip Rate. Equivalent to the spreading rate of the channel. It is either 1.2288 Mcps or 22

3.6864 Mcps. 23

Code Channel. A subchannel of a Forward CDMA Channel or Reverse CDMA Channel. 24

Each subchannel uses an orthogonal Walsh function or quasi-orthogonal function. 25

Code Division Multiple Access (CDMA). A technique for spread-spectrum multiple-access 26

digital communications that creates channels through the use of unique code sequences. 27

Common Assignment Channel (CACH). A forward common channel used by the base 28

station to acknowledge a mobile station accessing the Enhanced Access Channel, and in 29

the case of Reservation Access Mode, to transmit the address of a Reverse Common Control 30

Channel and associated Common Power Control Subchannel. 31

Common Power Control Channel (CPCCH). A forward common channel which transmits 32

power control bits (i.e., common power control subchannels) to multiple mobile stations. 33

The Common Power Control Channel is used by mobile stations operating in the 34

Reservation Access Mode. 35

Common Power Control Subchannel. A subchannel on the Common Power Control 36

Channel used by the base station to control the power of a mobile station when operating 37

on the Enhanced Access Channel or when operating in the Reservation Access Mode on the 38

Reverse Common Control Channel. 39

3GPP2 C.S0011-C v2.0

1-4

Continuous Transmission. A mode of operation in which Discontinuous Transmission is 1

not permitted. 2

Convolutional Code. A type of error-correcting code. A code symbol can be considered as 3

the convolution of the input data sequence with the impulse response of a generator 4

function. 5

orc

IE CPCCH . The ratio of the average transmit energy per PN chip for the Common Power 6

Control Channel to the total transmit power spectral density. 7

CRC. See Cyclic Redundancy Code. 8

Cyclic Redundancy Code (CRC). A class of linear error detecting codes which generate 9

parity check bits by finding the remainder of a polynomial division. See also Frame Quality 10

Indicator. 11

dBc. The ratio (in dB) of the sideband power of a signal, measured in a given bandwidth at 12

a given frequency offset from the center frequency of the same signal, to the total inband 13

power of the signal. For CDMA, the total inband power of the signal is measured in a 1.23 14

MHz bandwidth around the center frequency of the CDMA signal for a Spreading Rate 1 15

CDMA signal and in a 3.69 MHz bandwidth around the center frequency of the CDMA 16

signal for a Spreading Rate 3 CDMA signal. 17

dBm. A measure of power expressed in terms of its ratio (in dB) to one milliwatt. 18

dBm/Hz. A measure of power spectral density. The ratio, dBm/Hz, is the power in one 19

Hertz of bandwidth, where power is expressed in units of dBm. 20

DCCH_Chip_Bit. The number of PN chips per Dedicated Control Channel bit, equal to 128 21

for Spreading Rate 1 and 384 for Spreading Rate 3. 22

DCCH Ec. Average energy per PN chip for one Forward Dedicated Control Channel. For the 23

case when the Forward Power Control Subchannel is assumed to be transmitted at the 24

same power level that is used for the 9600 bps or 14400 bps data rate, the average energy 25

per PN chip for one Forward Dedicated Control Channel is 1211 × (total Forward Dedicated 26

Control Channel energy per PN chip). The total Forward Dedicated Control Channel is 27

comprised of traffic data and a Forward Power Control Subchannel. 28

orc

IE DCCH . The ratio of the average transmit energy per PN chip for one Forward 29

Dedicated Control Channel to the total transmit power spectral density. 30

Discontinuous Transmission (DTX). A mode of operation in which a base station or a 31

mobile station switches its transmitter or a particular code channel on and off 32

autonomously. For the case of DTX operation on the Forward Dedicated Control Channel 33

when power control bits are carried on that channel, the Forward Power Control 34

Subchannel is still transmitted. 35

dBW. A measure of power expressed in terms of its ratio (in dB) to one watt. 36

Eb. Average energy of an information bit at the mobile station antenna connector. 37

3GPP2 C.S0011-C v2.0

1-5

tb

NE . The ratio in dB of the combined received energy per bit to the effective noise power 1

spectral density at the base station antenna connector (see 1.4). If channel simulator is 2

used, then tb

NE

is referenced at the input of the channel simulator. 3

Ec. Average energy accumulated over one PN chip period (Ec). 4

orc

IE . The ratio in dB between the energy accumulated over one PN chip period (Ec) to the 5

total transmit power spectral density. 6

Effective Isotropic Radiated Power (EIRP). The product of the power supplied to the 7

antenna and the antenna gain in a direction relative to an isotropic antenna. 8

Effective Radiated Power (ERP). The product of the power supplied to the antenna and 9

the antenna gain relative to a half-wave dipole in a given direction. 10

EIB. See Erasure Indicator Bit. 11

EIRP. See Effective Isotropic Radiated Power. 12

Enhanced Access Channel (EACH). A reverse channel used by the mobile for 13

communicating to the base station. The Enhanced Access Channel operates in the Basic 14

Access Mode, Power Controlled Access Mode, and Reservation Access Mode. It is used for 15

transmission of short messages, such as signaling, MAC messages, response to pages, and 16

call originations. It can also be used to transmit moderate-sized data packets. 17

Enhanced Access Channel Preamble. A non-data bearing portion of the Enhanced Access 18

probe sent by the mobile station to assist the base station in initial acquisition and channel 19

estimation. 20

Enhanced Access Data. The data transmitted while in the Basic Access Mode or Power 21

Controlled Access Mode on the Enhanced Access Channel or while in the Reservation Mode 22

on a Reverse Common Control Channel. 23

Enhanced Access Header. A frame containing access origination information transmitted 24

immediately after the Enhanced Access Channel preamble while in the Power Controlled 25

Access Mode or Reservation Access Mode. 26

Enhanced Access Probe. One Enhanced Access Channel transmission consisting of an 27

Enhanced Access Channel preamble, optionally an Enhanced Access header, and 28

optionally Enhanced Access data. See also Enhanced Access Probe Sequence. 29

Enhanced Access Probe Sequence. A sequence of one or more Enhanced Access probes 30

on the Enhanced Access Channel. See also Enhanced Access Probe. 31

ERP. See Effective Radiated Power. 32

F-PDCCH0. Forward Packet Data Control Channel 0. The first Forward Packet Data 33

Control Channel. See also Forward Packet Data Control Channel. 34

3GPP2 C.S0011-C v2.0

1-6

FCH_Chip_Bit. The number of PN chips per Fundamental Channel bit, equal to 1

1228800/rb for Spreading Rate 1 and 3686400/rb for Spreading Rate 3, where rb is the 2

data rate of the Fundamental Channel. 3

FCH Ec. Average energy per PN chip for one Forward Fundamental Channel. For the case 4

when the Forward Power Control Subchannel is assumed to be transmitted at the same 5

power level that is used for the 9600 bps or 14400 bps data rate, the following equations 6

apply: 7

For Radio Configuration 1, it is equal to v11

11+

× (total Forward Fundamental Channel 8

energy per PN chip), where v equals 1 for 9600 bps, v equals 2 for 4800 bps, v equals 4 for 9

2400 bps, and v equals 8 for 1200 bps traffic data rate. For Radio Configuration 2, it is 10

equal to v23

23+

× (total Forward Fundamental Channel energy per PN chip), where v equals 11

1 for 14400 bps, v equals 2 for 7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 12

bps traffic data rate. The total Forward Fundamental Channel is comprised of traffic data 13

and a power control subchannel. For Radio Configurations 3, 4, 6, and 7, it is equal to 14

v1111

+× (total Forward Fundamental Channel energy per PN chip), where v equals 1 for 15

9600 bps, v equals 2 for 4800 bps, v equals 4 for 2700 bps, and v equals 8 for 1500 bps 16

traffic data rate. For Radio Configurations 5, 8, and 9, it is equal to v11

11+

× (total Forward 17

Fundamental Channel energy per PN chip), where v equals 1 for 14400 bps, v equals 2 for 18

7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 bps traffic data rate. The total 19

Forward Fundamental Channel is comprised of traffic data and a Forward Power Control 20

Subchannel. 21

orc

IE FCH . The ratio of the average transmit energy per PN chip for one Forward 22

Fundamental Channel to the total transmit power spectral density. 23

FCCCH_Chip_Bit. Number of PN chips per Forward Common Control Channel bit. For 24

Spreading Rate 1, FCCCH_Chip_Bit is equal to 32 x v where v equals 1 when the data rate 25

is 38400 bps, v equals 2 when the data rate is 19200 bps, and v equals 4 when the data 26

rate is 9600 bps. For Spreading Rate 3, FCCCH_Chip_Bit is equal to 96 x v where v equals 27

1 when the data rate is 38400 bps, v equals 2 when the data rate is 19200 bps, and v 28

equals 4 when the data rate is 9600 bps. 29

orc

IE FCCCH . The ratio of the average transmit energy per PN chip for the Forward 30

Common Control Channel to the total transmit power spectral density. 31

FER. Frame Error Rate of Forward Traffic Channel. The value of FER may be estimated by 32

using Service Option 2, 9, 30, 31, 32, 54 or 55. 33

Forward CDMA Channel. A CDMA Channel from a base station to mobile stations. The 34

Forward CDMA Channel contains one or more code channels that are transmitted on a 35

CDMA frequency assignment using a particular pilot PN offset. 36

3GPP2 C.S0011-C v2.0

1-7

Forward Common Control Channel (FCCCH). A control channel used for the 1

transmission of digital control information from a base station to one or more mobile 2

stations. 3

Forward Dedicated Control Channel (F-DCCH). A portion of a Radio Configuration 3 4

through 9 Forward Traffic Channel used for the transmission of higher-level data, control 5

information, and power control information from a base station to a mobile station. 6

Forward Fundamental Channel (F-FCH). A portion of a Forward Traffic Channel which 7

carries a combination of higher-level data and power control information. 8

Forward Packet Data Channel (F-PDCH). A portion of a Forward Traffic Channel which 9

carries higher-level data. 10

Forward Packet Data Control Channel (F-PDCCH). A control channel used for the 11

transmission of the control information for the subpacket being transmitted on the Forward 12

Packet Data Channel or to transmit control information. 13

Forward Power Control Subchannel. A subchannel on the Forward Fundamental 14

Channel or Forward Dedicated Control Channel used by the base station to control the 15

power of a mobile station when operating on the Reverse Traffic Channel. 16

Forward Supplemental Channel (F-SCH). A portion of a Radio Configuration 3 through 9 17

Forward Traffic Channel which operates in conjunction with a Forward Fundamental 18

Channel or a Forward Dedicated Control Channel in that Forward Traffic Channel to 19

provide higher data rate services, and on which higher-level data is transmitted. 20

Forward Supplemental Code Channel (SCCH). A portion of a Radio Configuration 1 and 2 21

Forward Traffic Channel which operates in conjunction with a Forward Fundamental 22

Channel in that Forward Traffic Channel, and (optionally) with other Forward 23

Supplemental Code Channels to provide higher data rate services, and on which higher-24

level data is transmitted. 25

Forward Traffic Channel. One or more code channels used to transport user and 26

signaling traffic from the base station to the mobile station. See Forward Fundamental 27

Channel, Forward Dedicated Control Channel, Forward Supplemental Channel, Forward 28

Supplemental Code Channel, and Forward Packet Data Channel. 29

FPC_PRI_CHANs. Power Control Subchannel indicator set by the base station to indicate 30

whether the mobile station is to perform the primary inner loop estimation on the received 31

Forward Fundamental Channel or the Forward Dedicated Control Channel. 32

Frame. A basic timing interval in the system. For the Sync Channel, a frame is 26.666... 33

ms long. For the Access Channel, the Paging Channel, the Broadcast Control Channel, the 34

Forward Supplemental Code Channel, and the Reverse Supplemental Code Channel, a 35

frame is 20 ms long. For the Forward Supplemental Channel and the Reverse 36

Supplemental Channel, a frame is 20, 40, or 80 ms long. For the Enhanced Access 37

Channel, the Forward Common Control Channel, and the Reverse Common Control 38

Channel, a frame is 5, 10, or 20 ms long. For the Forward Fundamental Channel, Forward 39

Dedicated Control Channel, Reverse Fundamental Channel, and Reverse Dedicated Control 40

Channel, a frame is 5 or 20 ms long. For the Common Assignment Channel, a frame is 5 41

ms long. 42

3GPP2 C.S0011-C v2.0

1-8

Frame Activity. The ratio of the number of active frames to the total number of frames 1

during channel operation. 2

Frame Offset. A time skewing of Forward Traffic Channel or Reverse Traffic Channel 3

frames from System Time in integer multiples of 1.25 ms. 4

Frame Quality Indicator. The CRC check applied to 9.6 and 4.8 kbps Traffic Channel 5

frames of Radio Configuration 1, all Forward Traffic Channel frames for Radio 6

Configurations 2 through 9, all Reverse Traffic Channel frames for Radio Configurations 2 7

through 6, the Broadcast Control Channel, Common Assignment Channel, Enhanced 8

Access Channel, and the Reverse Common Control Channel. 9

GHz. Gigahertz (109 Hertz). 10

Good Frame. A frame not classified as a bad frame. See also Bad Frame. 11

Good Message. A received message is declared a good message if it is received with a 12

correct CRC. 13

Handoff. The act of transferring communication with a mobile station from one base 14

station to another. 15

Hard Handoff. A handoff characterized by a temporary disconnection of the Traffic 16

Channel. Hard handoffs occur when the mobile station is transferred between disjoint 17

Active Sets, the CDMA frequency assignment changes, the frame offset changes, or the 18

mobile station is directed from a CDMA Traffic Channel to an analog voice channel. See 19

also Soft Handoff. 20

HPSK. Hybrid phase shift keying. 21

I0. The total received power spectral density, including signal and interference, as 22

measured at the mobile station antenna connector. 23

Ioc. The power spectral density of a band-limited white noise source (simulating 24

interference from other cells) as measured at the mobile station antenna connector. For 25

test cases where multiple channels or cells are specified, this power spectral density does 26

not include power from these multiple channels or cells. 27

Ior. The total transmit power spectral density of the Forward CDMA Channel at the base 28

station antenna connector. For transmit diversity test cases, it shall be the total combined 29

transmit power spectral density of the Forward CDMA Channel from both the main and 30

transmit diversity base station antenna connectors. 31

Îor. The received power spectral density of the Forward CDMA Channel as measured at the 32

mobile station antenna connector. 33

kHz. Kilohertz (103 Hertz). 34

Mcps. Megachips per second (106 chips per second). 35

Mean Input Power. The total received calorimetric power measured in a specified 36

bandwidth at the antenna connector, including all internal and external signal and noise 37

sources. 38

3GPP2 C.S0011-C v2.0

1-9

Mean Output Power. The total transmitted calorimetric power measured in a specified 1

bandwidth at the antenna connector when the transmitter is active. 2

MER. Message Error Rate. MER = 1 - dtransmitte messages ofNumber

received messages good ofNumber . 3

MHz. Megahertz (106 Hertz). 4

Mobile Station. A station intended to be used while in motion or during halts at 5

unspecified points. Mobile stations include portable units (e.g., hand-held personal units) 6

and units installed in vehicles. 7

Mobile Station Class. Mobile station classes define mobile station characteristics, such as 8

slotted operation and transmission power. 9

ms. Millisecond (10-3 second). 10

MSC. See Mobile Switching Center. 11

N0. The effective inband noise or interference power spectral density. 12

N/A. Not applicable. 13

Non-Slotted Mode. An operation mode of the mobile station in which the mobile station 14

continuously monitors the Paging Channel. 15

N/S. Not specified. 16

Nt. The effective noise power spectral density at the mobile station antenna connector. 17

OCNS. See Orthogonal Channel Noise Simulator. 18

OCNS Ec. Average energy per PN chip for the OCNS. 19

orc

IEOCNS . The ratio of the average transmit energy per PN chip for the OCNS to the total 20

transmit power spectral density. 21

Orthogonal Channel Noise Simulator. A hardware mechanism used to simulate the users 22

on the other orthogonal channels of a Forward CDMA Channel. 23

Orthogonal Transmit Diversity (OTD). A forward link transmission method which 24

distributes forward link channel symbols among multiple antennas and spreads the 25

symbols with a unique Walsh or quasi-orthogonal function associated with each antenna. 26

OTD. See orthogonal transmit diversity. 27

Packet. Physical Layer protocol data unit. 28

Packet Error Rate (PER). For multiple transmissions, a packet is declared in error if it has 29

insufficient frame quality after the last re-transmission defined for that test. 30

Paging Channel (PCH). A code channel in a Forward CDMA Channel used for transmission 31

of control information and pages from a base station to a mobile station. 32

Paging_Chip_Bit. Number of PN chips per Paging Channel bit, equal to 128 × v where v 33

equals 1 when the data rate is 9600 bps and v equals 2 when the data rate is 4800 bps. 34

3GPP2 C.S0011-C v2.0

1-10

Paging Ec. Average energy per PN chip for the Paging Channel. 1

orc

IEPaging . The ratio of the average transmit energy per PN chip for the Paging Channel 2

to the total transmit power spectral density. 3

orc

IE CCHPD . The ratio of the average transmit energy per PN chip for the Forward Packet 4

Data Control Channel to the total transmit power spectral density. 5

orc

IE CHPD . The ratio of the average transmit energy per PN chip for the Forward Packet 6

Data Channel to the total transmit power spectral density. 7

PDCCH_Chip_Bit. The number of PN chips per Packet Data Control Channel bit, equal to 8

1228800/rb, where rb is the data rate of the Packet Data Control Channel. 9

PDCH_Chip_Bit. The number of PN chips per Packet Data Channel bit, equal to 10

1228800/rb, where rb is the data rate of the Packet Data Channel. 11

PER. See packet error rate. 12

Physical Layer. The part of the communication protocol between the mobile station and 13

the base station that is responsible for the transmission and reception of data. The physical 14

layer in the transmitting station is presented a frame and transforms it into an over-the-air 15

waveform. The physical layer in the receiving station transforms the waveform back into a 16

frame. 17

Piece-wise Linear FER Curve. An FER-versus-Eb/Nt curve in which the FER vertical axis 18

is in log scale and the Eb/Nt horizontal axis is in linear scale expressed in dB, obtained by 19

interpolating adjacent test data samples with straight lines. 20

Piece-wise Linear MER Curve. An MER-versus-Eb/Nt curve in which the MER vertical 21

axis is in log scale and the Eb/Nt horizontal axis is in linear scale expressed in dB, 22

obtained by interpolating adjacent test data samples with straight lines. 23

Pilot Channel. An unmodulated, direct-sequence spread spectrum signal transmitted by a 24

CDMA base station or mobile station. A pilot channel provides a phase reference for 25

coherent demodulation and may provide a means for signal strength comparisons between 26

base stations for determining when to handoff. 27

Pilot Ec. Average energy per PN chip for the Pilot Channel. 28

oc

IE Pilot . The ratio of the combined pilot energy per chip, Ec, to the total received power 29

spectral density (noise and signals), I0, of at most K usable multipath components at the 30

mobile station antenna connector (see 1.4). K is the number of demodulating elements 31

supported by the mobile station. 32

orc

IEPilot . The ratio of the average transmit energy per PN chip for the Pilot Channel to the 33

total transmit power spectral density. 34

3GPP2 C.S0011-C v2.0

1-11

Pilot PN Sequence. A pair of modified maximal length PN sequences used to spread the 1

Forward CDMA Channel and the Reverse CDMA Channel. Different base stations are 2

identified by different pilot PN sequence offsets. 3

PN. Pseudonoise. 4

PN Chip. One bit in the PN sequence. 5

PN Sequence. Pseudonoise sequence. A periodic binary sequence. 6

Power Control Bit. A bit sent on the Forward Power Control Subchannel, Reverse Power 7

Control Subchannel, or Common Power Control Subchannel to signal the mobile station or 8

base station to increase or decrease its transmit power. 9

Power Control Ec. Average energy per PN chip for the Forward Power Control Subchannel. 10

For the case when the Forward Power Control Subchannel is assumed to be transmitted at 11

the same power level that is used for the 9600 bps or 14400 bps data rate, the following 12

equations apply: 13

For Radio Configuration 1, it is equal to v11

v+

× (total Forward Fundamental Channel 14


2400 bps, and v equals 8 for 1200 bps traffic data rate. For Radio Configuration 2, it is 16

equal to v23

v+

× (total Forward Fundamental Channel energy per PN chip), where v equals 17

1 for 14400 bps, v equals 2 for 7200 bps, v equals 4 for 3600 bps, and v equals 8 for 1800 18

bps traffic data rate. For Radio Configurations 3, 4, 6, and 7, it is equal to v11

v+

× (total 19

Forward Fundamental Channel or Forward Dedicated Control Channel energy per PN chip), 20

where v equals 1 for 9600 bps, v equals 2 for 4800 bps, v equals 4 for 2700 bps, and v 21

equals 8 for 1500 bps traffic data rate. For Radio Configurations 5, 8, and 9, it is equal to 22

v11v+

× (total Forward Fundamental Channel or Forward Dedicated Control Channel 23


3600 bps, and v equals 8 for 1800 bps traffic data rate. The total Forward Fundamental 25

Channel or Forward Dedicated Control Channel is comprised of traffic data and a power 26

control subchannel. 27

orc

IEControlPower . The ratio of the average transmit energy per PN chip for the Forward 28

Power Control Subchannel to the total transmit power spectral density. 29

Power Control Group. A 1.25 ms interval on the Forward Traffic Channel, the Reverse 30

Traffic Channel, and the Reverse Pilot Channel. See also Power Control Bit. 31

Power Controlled Access Mode. A mode used on the Enhanced Access Channel where a 32

mobile station transmits an Enhanced Access preamble, an Enhanced Access header, and 33

Enhanced Access data in the Enhanced Access probe using closed loop power control. 34

Power Up Function (PUF). A method by which the mobile station increases its output 35

power to support location services. 36

3GPP2 C.S0011-C v2.0

1-12

ppm. Parts per million. 1

Preamble. See Access Channel preamble, Enhanced Access Channel preamble, Reverse 2

Common Control Channel preamble, and Reverse Traffic Channel Preamble. 3

Primary Paging Channel. The default code channel (code channel 1) assigned for paging 4

on a CDMA Channel. 5

Protocol Data Unit (PDU). Encapsulated data communicated between peer layers on the 6

mobile station and the base station. 7

PS. Pilot Strength. Also see Pilot Ec/I0. 8

PUF. See Power Up Function. 9

PUF Probe. One or more consecutive frames on the Reverse Traffic Channel within which 10

the mobile station transmits the PUF pulse. 11

PUF Pulse. Portion of PUF probe which may be transmitted at elevated output power. 12

PUF Target Frequency. The CDMA frequency to which the base station directs a mobile 13

station for transmitting the PUF probe. 14

QIB. See Quality Indicator Bit. 15

QPSK. Quadrature phase shift keying. 16

Quality Indicator Bit (QIB). A bit used in the Radio Configurations 3, 4, 5, and 6 Reverse 17

Power Control Subchannel to indicate signal quality on the Forward Dedicated Control 18

Channel. When the Forward Fundamental Channel is present, this bit is set the same as 19

the Erasure Indicator Bits. 20

Quick Paging Channel (QPCH). An uncoded, spread, and On-Off-Keying (OOK) modulated 21

spread spectrum signal sent by a base station to inform mobile stations operating in the 22

slotted mode during the idle state whether to receive the Forward Common Control 23

Channel or the Paging Channel starting in the next Forward Common Control Channel or 24

Paging Channel frame. 25

QPCH_Chip_Bit. Number of PN chips per Quick Paging Channel bit. For Spreading Rate 1, 26

Quick Paging_Chip_Bit is equal to 256 x v where v equals 1 when the data rate is 4800 bps 27

and v equals 2 when the data rate is 2400 bps. For Spreading Rate 3, Quick 28

Paging_Chip_Bit is equal to 768 x v where v equals 1 when the data rate is 4800 bps and v 29

equals 2 when the data rate is 2400 bps. 30

orc

IE QPCH . The ratio of the average transmit energy per PN chip for the Quick Paging 31

Channel to the total transmit power spectral density. 32

Radio Configuration (RC). A set of Forward Traffic Channel and Reverse Traffic Channel 33

transmission formats that are characterized by physical layer parameters such as 34

transmission rates, modulation characteristics, and spreading rate. 35

RC. See Radio Configuration. 36

Reservation Access Mode. A mode used on the Enhanced Access Channel and Reverse 37

Common Control Channel where a mobile station transmits an Enhanced Access preamble 38

3GPP2 C.S0011-C v2.0

1-13

and an Enhanced Access header in the Enhanced Access probe. The Enhanced Access data 1

is transmitted on a Reverse Common Control Channel using closed loop power control. 2

Reverse Acknowledgment Channel. A portion of a Reverse CDMA Channel used for the 3

transmission of acknowledgments from the mobile station to the base station in response 4

to the data received on the Forward Packet Data Channel and the Forward Packet Data 5

Control Channel. 6

Reverse CDMA Channel. The CDMA Channel from the mobile station to the base station. 7

From the base station’s perspective, the Reverse CDMA Channel is the sum of all mobile 8

station transmissions on a CDMA frequency assignment. 9

Reverse Channel Quality Indicator Channel. A portion of a Reverse CDMA Channel used 10

by the mobile station to indicate to the base station the quality of the Forward Link Pilot 11

Channel received at the mobile station, and to indicate switching between base stations. 12

Reverse Common Control Channel. A portion of a Reverse CDMA Channel used for the 13

transmission of digital control information from one or more mobile stations to a base 14

station. It can be power and may support soft handoff. 15

Reverse Dedicated Control Channel (R-DCCH). A portion of a Radio Configuration 3 16

through 6 Reverse Traffic Channel used for the transmission of higher-level data and 17

control information from a mobile station to a base station. 18

Reverse Fundamental Channel (R-FCH). A portion of a Reverse Traffic Channel which 19

carries higher-level data and control information from a mobile station to a base station. 20

Reverse Pilot Channel (R-PICH). An unmodulated, direct-sequence spread spectrum 21

signal transmitted continuously by a CDMA mobile station. A reverse pilot channel 22

provides a phase reference for coherent demodulation and may provide a means for signal 23

strength measurement. 24

Reverse Power Control Subchannel. A subchannel on the Reverse Pilot Channel used by 25

the mobile station to control the power of a base station when operating on the Forward 26

Traffic Channel with Radio Configurations 3 through 9. 27

Reverse Supplemental Channel (R-SCH). A portion of a Radio Configuration 3 through 6 28

Reverse Traffic Channel which operates in conjunction with the Reverse Fundamental 29

Channel or the Reverse Dedicated Control Channel in that Reverse Traffic Channel to 30

provide higher data rate services, and on which higher-level data is transmitted. 31

Reverse Traffic Channel. A traffic channel on which data and signaling are transmitted 32

from a mobile station to a base station. The Reverse Traffic Channel is composed of up to 33

one Reverse Dedicated Control Channel, up to one Reverse Fundamental Channel, zero to 34

two Reverse Supplemental Channels, and zero to seven Reverse Supplemental Code 35

Channels. 36

RF Carrier. A direct-sequence spread RF channel. For the Forward CDMA Channel, the 37

number of RF carriers is equal to the Spreading Rate; for the Reverse CDMA Channel, there 38

is one RF carrier. 39

RMS. Root of Mean Square. 40

3GPP2 C.S0011-C v2.0

1-14

SCCH_Chip_Bit. The number of PN chips per Supplemental Code Channel bit, equal to 1


data rate of the Supplemental Code Channel. 3

SCH_Chip_Bit. The number of PN chips per Supplemental Channel bit, equal to 4


data rate of the Supplemental Channel. 6

SCCH Ec. Average energy per PN chip for one Forward Supplemental Code Channel. 7

SCH Ec. Average energy per PN chip for one Forward Supplemental Channel. 8

orc

IE SCCH . The ratio of the average transmit energy per PN chip for one Forward 9

Supplemental Code Channel to the total transmit power spectral density. 10

orc

IE SCH . The ratio of the average transmit energy per PN chip for one Forward 11

Supplemental Channel to the total transmit power spectral density. 12

Service Option 2. Loopback service option for Radio Configuration 1 as specified in [10]. 13

Service Option 9. Loopback service option for Radio Configuration 2 as specified in [10]. 14

Service Option 30. Mobile station data loopback test mode for Multiplex Option 1 15

Supplemental Channel as specified in [10]. 16

Service Option 31. Mobile station data loopback test mode for Multiplex Option 2 17

Supplemental Channel as specified in [10]. 18

Service Option 32. Test data service option for Radio Configurations 3 through 6 on the 19

Reverse Traffic Channel and Radio Configurations 3 through 9 on the Forward Traffic 20

Channel as specified in [8]. 21

Service Option 54. Markov service option for Radio Configurations 1 through 6 on the 22



Service Option 55. Loopback service option for Radio Configurations 1 through 6 on the 25



Serving Frequency. The CDMA frequency on which a mobile station is currently 28

communicating with one or more base stations. 29

Slotted Mode. An operation mode of the mobile station in which the mobile station 30

monitors only selected slots on the Paging Channel. 31

Soft Handoff. A handoff occurring while the mobile station is in the Mobile Station Control 32

on the Traffic Channel State. This handoff is characterized by commencing communications 33

with a new base station on the same CDMA frequency assignment before terminating 34

communications with the old base station. See Hard Handoff. 35

3GPP2 C.S0011-C v2.0

1-15

Space Time Spreading (STS). A forward link transmission method which transmits all 1

forward link channel symbols on multiple antennas and spreads the symbols with 2

complementary Walsh or quasi-orthogonal functions. 3

Spreading Rate (SR). The PN chip rate of the Forward CDMA Channel or the Reverse 4

CDMA Channel, defined as a multiple of 1.2288 Mcps. 5

Spreading Rate 1. Spreading Rate 1 is often referred to as “1X.” A Spreading Rate 1 6

Forward CDMA Channel uses a single direct-sequence spread carrier with a chip rate of 7

1.2288 Mcps. A Spreading Rate 1 Reverse CDMA Channel uses a single direct-sequence 8

spread carrier with a chip rate of 1.2288 Mcps. 9

Spreading Rate 3. Spreading Rate 3 is often referred to as “3X.” A Spreading Rate 3 10

Forward CDMA Channel uses three direct-sequence spread carriers each with a chip rate 11

of 1.2288 Mcps. A Spreading Rate 3 Reverse CDMA Channel uses a single direct-sequence 12

spread carrier with a chip rate of 3.6864 Mcps. 13

SR. See Spreading Rate. 14

STS. See Space Time Spreading. 15

Symbol. See Code Symbol and Modulation Symbol. 16

Sync Channel. Code channel 32 in the Forward CDMA Channel, which transports the 17

synchronization message to the mobile station. 18

Sync_Chip_Bit. Number of PN chips per Sync Channel bit, equal to 1024. 19

Sync Ec. Average energy per PN chip for the Sync Channel. 20

orc

IESync . The ratio of the average transmit energy per PN chip for the Sync Channel to 21

the total transmit power spectral density. 22

Target Frequency. The CDMA frequency assignment to which the base station directs a 23

mobile station in a handoff using an Extended Handoff Direction Message, a General 24

Handoff Direction Message, or a Universal Handoff Direction Message. 25

TD. Transmit Diversity schemes, including OTD and STS. 26

orc

IE Pilot TD . The ratio of the average transmit energy per PN chip for the Transmit 27

Diversity Pilot Channel to the total transmit power spectral density. 28

Time Reference. A reference established by the mobile station that is synchronous with 29

the earliest arriving multipath component used for demodulation. 30

Traffic Channel. A communication path between a mobile station and a base station used 31

for user and signaling traffic. The term Traffic Channel implies a Forward Traffic Channel 32

and Reverse Traffic Channel pair. See also Forward Traffic Channel and Reverse Traffic 33

Channel. 34

Traffic Ec. See DCCH Ec and FCH Ec. 35

3GPP2 C.S0011-C v2.0

1-16

orc

IE Traffic . See

orc

IE DCCH

and or

cI

E FCH . For Radio Configuration 1 and 2, the term 1

applies to the Fundamental Channel. For Radio Configuration 3 through 9, the term 2

applies both to the Fundamental Channel and Dedicated Control Channel. 3

Turbo Code. A type of error-correcting code. A code symbol is based on the outputs of the 4

two recursive convolutional codes (constituent codes) of the Turbo code. 5

Valid Power Control Bit. A valid power control bit is sent on the Forward Power Control 6

Subchannel in the second power control group following the corresponding Reverse Traffic 7

Channel power control group which was not gated off and in which the signal strength was 8

estimated. See 3.1.3.1.10 of [4]. 9

Walsh Function. One of 2N time orthogonal binary functions (note that the functions are 10

orthogonal after mapping ‘0’ to 1 and ‘1’ to -1). 11

1.3 Test Modes 12

The Forward Traffic Channel is verified by invoking Fundamental Channel test modes, 13

Dedicated Control Channel test modes, Supplemental Code Channel test modes, 14

Supplemental Channel test modes, and Packet Data Channel test modes. The Reverse 15

Traffic Channel is verified by invoking Fundamental Channel test modes, Dedicated Control 16

Channel test modes, and Supplemental Channel test modes. Table 1.3-1 lists the test 17

modes and the mapping to radio configurations. 18

19

Table 1.3-1. Test Configuration Combinations 20

Test Mode Forward Traffic Channel Radio Configuration

Reverse Traffic Channel Radio Configuration

1 1 1

2 2 2

3 3 3

4 4 3

5 5 4

6 6 5

7 7 5

8 8 6

9 9 6

10a 10 3

Note: Test Mode 10b will be defined in the next revision of this Standard.

21

Fundamental Channel Test Mode 1 is entered by setting up a call using the Loopback 22

Service Option (Service Option 2 or 55) or the Markov Service Option (Service Option 54). 23

3GPP2 C.S0011-C v2.0

1-17

Fundamental Channel Test Mode 2 is entered by setting up a call using the Loopback 1

Service Option (Service Option 9 or 55) or the Markov Service Option (Service Option 54). 2

Fundamental Channel Test Modes 3 through 9 are entered by setting up a call using the 3

Loopback Service Option (Service Option 55), Markov Service Option (Service Option 54), or 4

Test Data Service Option (Service Option 32). 5

Dedicated Control Channel Test Modes 3 through 9, Supplemental Channel Test Modes 3 6

through 9, and Packet Data Channel Test Mode 10a are entered by setting up a call using 7

the Test Data Service Option (Service Option 32). 8

Supplemental Code Channel Test Mode 1 is entered by setting up a call using the 9

Loopback Service Option (Service Option 30). 10

Supplemental Code Channel Test Mode 2 is entered by setting up a call using the 11

Loopback Service Option (Service Option 31). 12

The mobile station shall support the Loopback Service Option if the mobile station 13

supports a Forward Fundamental Channel, Reverse Fundamental Channel or Forward 14

Supplemental Code Channel. The mobile station shall support the Test Data Service Option 15

if it supports a Forward Dedicated Control Channel, Reverse Dedicated Control Channel, 16

Forward Supplemental Channel, Reverse Supplemental Channel, or Forward Packet Data 17

Channel. The mobile station may support the Markov Service Option if the mobile station 18

supports a Forward Fundamental Channel or a Reverse Fundamental Channel. 19

1.4 CDMA Equations 20

The equations listed below describe the relationship between various test parameters under 21

different conditions. If the Paging Channel is not supported, the Forward Common Control 22

Channel may be substituted. 23

1.4.1 Transmit Power of the Base Station 24

orc

IEPilot +

or

cI

E Pilot TD +

orc

IE Sync +

or

cI

E QPCH +

orc

IEPaging

+ 25

or

cI

E FCCCH +

or

cI

E BCCH +

or

cI

E CACH +

or

cI

E CPCCH +

or

cI

E FCH + 26

or

cI

E DCCH +

orc

IE ControlPower +

or

cI

E SCCH +

or

cI

E SCH +

orc

IE PDCCH + 27

orc

IE PDCH

+ or

cI

E OCNS = 1 28

In the tests defined in this document, the following values are usually used: 29

orc

IEPilot = -7 dB 30

orc

IE Sync = -16 dB 31

3GPP2 C.S0011-C v2.0

1-18

orc

IEPaging

= -12 dB or or

cI

E FCCCH = -12 dB 1

Therefore, if or

cI

E Traffic = -16 dB at 9600 bps data rate, then 2

or

cI

E ControlPower = -26.41 dB 3

orc

IE OCNS = -1.64 dB 4

Otherwise, if or

cI

E Traffic = -16 dB at 1200 bps data rate, then 5

orc

IE ControlPower = -17.38 dB 6

orc

IE OCNS = -1.75 dB 7

1.4.2 Received Signal Strength for Mobile Station Not in Handoff 8

For the purpose of calculating the constant expression ocor

II or its inverse, orI is the long 9

term average over the test interval. For the purpose of calculating the various channel or

cIE

10

ratios, orI is the long term average over the test interval. 11

0

cI

E Pilot =

1II

IE Pilot

or

ocor

c

+ 12

1.4.2.1 Single-Path Case 13

t

bN

E Sync =

or

ocor

c

II

Bit_Chip_SyncI

E Sync×

14

3GPP2 C.S0011-C v2.0

1-19

t

bN

E QPCH =

or

ocor

c

II

Bit_Chip_QPCHI

E QPCH×

1

t

bN

EPaging =

or

ocor

c

II

Bit_Chip_PagingI

EPaging ×

2

t

bN

E BCCH =

or

ocor

c

II

Bit_Chip_BCCHI

E BCCH×

3

t

bN

E FCCCH =

or

ocor

c

II

Bit_Chip_FCCCHI

E FCCCH×

4

t

bN

E FCH =

or

ocor

c

II

Bit_Chip_FCHI

E FCH×

5

t

bN

E DCCH =

or

ocor

c

II

Bit_Chip_DCCHI

E DCCH×

6

t

bN

E SCCH =

or

ocor

c

II

Bit_Chip_SCCHI

E SCCH×

7

t

bN

E SCH =

or

ocor

c

II

Bit_Chip_SCHI

E SCH×

8

3GPP2 C.S0011-C v2.0

1-20

tb

NE PDCCH

=

or

ocor

c

II

Bit_Chip_PDCCHI

E PDCCH×

1

tb

NE PDCH

=

or

ocor

c

II

Bit_Chip_PDCHI

E PDCH×

2

1.4.2.2 Two-Path Case 3

According to Channel Simulator Configuration 1, 2 and 5 (see 6.4.1.3), these two paths 4

have the same average power. 5

t

bN

E BCCH =

or

cI

E BCCH × BCCH_Chip_Bit ×

21

II

1

or

oc + 6

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit ×

21

II

1

or

oc + 7

t

bN

E DCCH =

or

cI

E DCCH × DCCH_Chip_Bit ×

21

II

1

or

oc + 8

t

bN

E SCH =

or

cI

E SCH × SCH_Chip_Bit ×

21

II

1

or

oc + 9

tb

NE PDCCH =

orc

IE PDCCH × PDCCH_Chip_Bit ×

21

II

1

or

oc + 10

tb

NE PDCH =

orc

IE PDCH × PDCH_Chip_Bit ×

21

II

1

or

oc + 11

3GPP2 C.S0011-C v2.0

1-21

1.4.2.3 Three-Path Case 1

According to Channel Simulator Configuration 4 (see 6.4.1.3), the first two paths have the 2

same average power and the third path has half the average power of the first one. 3

t

bN

E BCCH =

orc

IE BCCH × BCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 4

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 5

DCCH tb

NE

= or

cI

E DCCH × DCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 6

t

bN

E SCH =

or

cI

E SCH × SCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 7

tb

NE PDCCH

= or

cI

E PDCCH × PDCCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 8

tb

NE PDCH

= or

cI

E PDCH × PDCH_Chip_Bit × (2 ×

53

II

52

or

oc + +

54

II

51

or

oc +) 9

1.4.3 Received Signal Strength for Mobile Station in Two-Way Handoff 10

According to Channel Simulator Configuration 2 (see 6.4.1.3), which is used in the tests of 11

the Forward Traffic Channel in two-way handoff, there are two paths from each cell and the 12

power received from each cell is Îor. 13

3GPP2 C.S0011-C v2.0

1-22

For the purpose of calculating the constant expression ocor

II

or its inverse, orI is the long 1

term average over the test interval. For the purpose of calculating the various channel or

cIE

2

ratios, orI is the long term average over the test interval. 3

0

cI

E Pilot(for each pilot) =

2II

IEPilot

or

ocor

c

+ 4

t

bN

E FCH =

or

cI

E FCH × FCH_Chip_Bit ×

23

II

23

or

oc + 5

Generally, if the power received from cell 1 and cell 2 are Îor1 and Îor2, respectively, then 6

0

cI

E Pilot1 =

1II

II

IEPilot

1or2or

1oroc

1or

c

++ 7

0

cI

E Pilot2 =

1II

II

IEPilot

2or1or

2oroc

2or

c

++ 8

1.5 Tolerances 9

1.5.1 CDMA System Parameter Tolerances 10

CDMA parameters are specified in [4]. All parameters indicated in Sections 3 and 4 are 11

exact unless an explicit tolerance is stated. 12

1.5.2 Measurement Tolerances 13

Unless otherwise specified, a measurement tolerance, including the tolerance of the 14

measurement equipment, of ±10% is assumed. 15

Unless otherwise specified, the Îor /Ioc value shall be within ±0.1 dB of the value specified, 16

and the Ioc value shall be within ±5 dB of the value specified. 17

1.6 Test Requirements for Mobile Stations Supporting Analog Operation 18

Mobile stations supporting analog operation in the 800 MHz band shall conform to all 19

requirements in [3], with the exception of the test variations included in this section. 20

3GPP2 C.S0011-C v2.0

1-23

1.6.1 Modulated Tone Frequency 1

[3] states that a modulated tone frequency of 1000 Hz should be used in many tests. A 2

1004 Hz modulated tone frequency may be used in lieu of 1000 Hz. 3

Formatted: Left

3GPP2 C.S0011-C v2.0

1-24

No text1

3GPP2 C.S0011-C v2.0

2-1

2 STANDARD RADIATED EMISSIONS MEASUREMENT PROCEDURE 1

The measurement and calibration procedures described are intended to provide an 2

overview of radiated and conducted signal measurements. A detailed description of the 3

required measurement procedures is given in [1]. 4

2.1 Standard Radiation Test Site 5

The test site shall be on level ground that is of uniform electrical characteristics. The site 6

shall be clear of overhead wires and other metallic objects and shall be as free as possible 7

from undesired signals, such as ignition noise and other carriers. Reflecting objects, such 8

as rain gutters and power cables shall lie outside an ellipse measuring 60 meters on the 9

major axis by 52 meters on the minor axis for a 30-meter site, or an ellipse measuring 6 10

meters on the major axis by 5.2 meters on the minor axis for a 3-meter site. The equipment 11

under test shall be located at one focus of the ellipse and the measuring antenna at the 12

other focus. If desired, shelters may be provided at the test site to protect the equipment 13

and personnel. All such construction shall be of wood, plastic, or other non-metallic 14

material. All power, telephone, and control circuits to the site shall be buried at least 0.3 15

meter under ground. 16

A turntable, essentially flush with the ground, shall be provided that can be remotely 17

controlled. A platform 1.2 meters high shall be provided on this turntable to hold the 18

equipment under test. Any power and control cables that are used for this equipment 19

should extend down to the turntable, and any excess cabling should be coiled on the 20

turntable. 21

If the equipment to be tested is mounted in racks and is not easily removed for testing on 22

the above platform, then the manufacturer may elect to test the equipment when it is 23

mounted in its rack (or racks). In this case, the rack (or racks) may be placed directly on 24

the turntable. 25

If a transmitter with an external antenna connection is being tested, then the RF output of 26

this transmitter shall be terminated in a non-radiating load that is placed on the turntable. 27

A non-radiating load is used in lieu of an antenna to avoid interference with other radio 28

users. The RF cable to this load should be of minimum length. The transmitter shall be 29

tuned and adjusted to its rated output value before starting the tests. 30

In order to conduct unintentional radiator tests as specified in Part 15, subpart B of [2], the 31

radiation site must comply with Sections 5.4.6 through 5.5 of [1] as required by Part 2.948 32

of [2]. 33

2.2 Search Antenna 34

For narrow-band dipole adjustable search antennas, the dipole length shall be adjusted for 35

each measurement frequency. This length may be determined from a calibration ruler that 36

is normally supplied with the equipment. 37

The search antenna shall be mounted on a movable non-metallic horizontal boom that can 38

be raised or lowered on a wooden or other non-metallic pole. The cable connected to the 39

search antenna shall be at a right angle to the antenna. The cable shall be dressed at least 40

3GPP2 C.S0011-C v2.0

2-2

3 meters, either through or along the horizontal boom, in a direction away from the 1

equipment being measured. The search antenna cable may then be dropped from the end 2

of the horizontal boom to ground level for connection to the field-strength measuring 3

equipment. 4

The search antenna shall be capable of being rotated 90 degrees on the end of the 5

horizontal boom to allow measurement of both vertically and horizontally polarized signals. 6

When the antenna length of a vertically mounted antenna does not permit the horizontal 7

boom to be lowered to its minimum specified search range, adjust the minimum height of 8

the boom for 0.3 meter clearance between the end of the antenna and the ground. 9

2.3 Field-Strength Measurement 10

A field-strength meter shall be connected to a search antenna. The field-strength meter 11

shall have sufficient sensitivity and selectivity to measure signals over the required 12

frequency ranges at levels at least 10 dB below the levels specified in any document, 13

standard, or specification that references this measurement procedure. The calibration of 14

the measurement instruments (field-strength meter, antennas, etc.) shall be checked 15

frequently to ensure that their accuracy is in accordance with the current standards. Such 16

calibration checks shall be performed at least once per year. 17

2.4 Frequency Range of Measurements 18

When measuring radiated signals from transmitting equipment, the measurements shall be 19

made from the lowest radio frequency (but no lower than 25 MHz) generated in the 20

equipment to the tenth harmonic of the carrier, except for that region close to the carrier 21

equal to ±250% of the authorized bandwidth. 22

When measuring radiated signals from receiving equipment, the measurements shall be 23

made from 25 MHz to at least 6 GHz. 24

2.5 Test Ranges 25

2.5.1 30-Meter Test Range 26

Measurement of radiated signals shall be made at a point 30 meters from the center of the 27

turntable. The search antenna shall be raised and lowered from 1 to 4 meters in both 28

horizontally and vertically polarized orientations. 29

The field-strength measuring meter may be placed on a suitable table or tripod at the foot 30

of the mast. 31

When measuring radiated emissions from receivers, equipment that contains its own 32

receive antenna shall be tested with the antenna in place. Equipment that is connected to 33

an external receive antenna via a cable shall be tested without the antenna, and the receive 34

ports on the equipment under test shall be terminated in a 50Ω non-radiating resistive 35

load. 36

3GPP2 C.S0011-C v2.0

2-3

2.5.2 3-Meter Test Range 1

Measurement of radiated signals may be made at a point 3 meters from the center of the 2

turntable, provided the following three conditions can be met: 3

1. A ground screen that covers an elliptical area at least 6 meters on the major axis 4

by 5.2 meters on the minor axis is used with the measuring antenna and turntable 5

mounted 3 meters apart. The measuring antenna and turntable shall lie on the 6

major axis and shall be equidistant from the minor axis of the elliptical area. 7

2. The maximum dimension of the equipment shall be 3 meters or less. When 8

measuring radiated signals from receivers, the maximum dimension shall include 9

the antenna if it is an integral part of the device. 10

3. The field-strength measuring equipment is either mounted below the ground level 11

at the test site or is located a sufficient distance away from the equipment being 12

tested and from the search antenna to prevent corruption of the measured data. 13

The search antenna shall be raised and lowered over a range from 1 to 4 meters in both 14

horizontally and vertically polarized orientations. When the search antenna is vertically 15

oriented, the minimum height of the center of the search antenna shall be defined by the 16

length of the lower half of the search antenna. 17

When measuring radiated emissions from receivers, equipment that contains its own 18

receive antenna shall be tested with the antenna in place. Equipment that is connected to 19

an external receive antenna via a cable shall be tested without the antenna, and the receive 20

ports on the equipment under test shall be terminated in a 50Ω non-radiating resistive 21

load. The 3-meter test range may be used for determining compliance with limits specified 22

at 30 meters (or other distances), provided that: 23

1. The ground reflection variations between the two distances have been calibrated for 24

the frequencies of interest at the test range, or 25

2. A 5 dB correction factor is added to the specified radiation limit(s) to allow for 26

average ground reflections. 27

Radiated field strength (volts/meter) varies inversely with distance, so that a measurement 28

made on the 3-meter test range divided by 10 gives the equivalent value that would be 29

measured on a 30-meter test range for the same EIRP (effective isotropic radiated power). 30

The 30-meter field strength in volts/meter can be calculated from the EIRP by using the 31

following formula: 32

µV/m @ 30 meters = 5773.5 × 10EIRP(dBm)/20 33

2.6 Radiated Signal Measurement Procedures 34

Radiated signals having significant levels shall be measured on the 30-meter or the 3-meter 35

range by using the following procedure: 36

1. For each observed radiated signal, raise and lower the search antenna to obtain a 37

maximum reading on the field-strength meter with the antenna horizontally 38

polarized. Then rotate the turntable to maximize the reading. Repeat this 39

3GPP2 C.S0011-C v2.0

2-4

procedure of raising and lowering the antenna and rotating the turntable until the 1

highest possible signal has been obtained. Record this maximum reading. 2

2. Repeat step 1 for each observed radiated signal with the antenna vertically 3

polarized. 4

3. Remove the equipment being tested and replace it with a half-wave antenna. The 5

center of the half-wave antenna should be at the same approximate location as the 6

center of the equipment being tested. 7

4. Feed the half-wave antenna replacing the equipment under test with a signal 8

generator connected to the antenna by means of a non-radiating cable. With the 9

antennas at both ends horizontally polarized and with the signal generator tuned 10

to the observed radiated signal, raise and lower the search antenna to obtain a 11

maximum reading on the field-strength measuring meter. Adjust the level of the 12

signal generator output until the previously recorded maximum reading for this set 13

of conditions is obtained. Record the signal generator power output. 14

5. Repeat step 4 above with both antennas vertically polarized. 15

6. Calculate the power into a reference ideal isotropic antenna by: 16

a. First reducing the readings obtained in steps 4 and 5 above by the power loss 17

in the cable between the generator and the source antenna, and 18

b. Then correcting for the gain of the source antenna used relative to an ideal 19

isotropic antenna. The reading thus obtained is the equivalent effective 20

isotropic radiated power (EIRP) level for the spurious signal being measured. 21

7. Repeat steps 1 through 6 above for all observed signals from the equipment being 22

tested. 23

24

3GPP2 C.S0011-C v2.0

3-1

3 CDMA RECEIVER MINIMUM STANDARDS 1

3.1 Frequency Coverage Requirements 2

The RF channel numbers and frequencies are given for base stations and mobile stations in 3

[11]. The mobile station receive CDMA frequency assignments are associated on a one-to-4

one basis with the transmit CDMA frequency assignments. Each CDMA frequency 5

assignment shall be centered at one of the indicated frequencies. 6

3.2 Acquisition Requirements 7

3.2.1 Idle Handoff Tests 8

3.2.1.1 Idle Handoff in Non-Slotted Mode on the Paging Channel 9

These tests shall be performed for mobile stations that can operate in non-slotted mode 10

while in the Mobile Station Idle State. 11

3.2.1.1.1 Definition 12

When in the Mobile Station Idle State, the mobile station continually searches for the 13

strongest Pilot Channel signal on the current CDMA frequency assignment. The mobile 14

station determines that an idle handoff should occur when it detects a Pilot Channel signal 15

sufficiently stronger than the one it is currently monitoring. 16

Test 1 verifies that the mobile station does not perform alternating idle handoffs between 17

two Pilot Channels so frequently that the mobile station cannot receive paging messages on 18

either of the Forward CDMA Channels by checking the number of idle handoffs performed 19

and the Paging Channel message error rate (MER). 20

Test 2 verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 21

pilot in the Neighbor Set exceeds the Ec/I0 of the pilot in the Active Set by 3 dB, as 22

measured at the mobile station antenna connector, for a period longer than one second. 23

This is accomplished by checking the number of idle handoffs performed and the Paging 24

Channel MER. 25

3.2.1.1.2 Method of Measurement 26

1. Connect two base stations and an AWGN generator to the mobile station antenna 27

connector as shown in Figure 6.5.1-3. The Forward Channel from base station 1 28

has an arbitrary pilot PN offset index P1, and is called Channel 1. The Forward 29

Channel from base station 2 has an arbitrary pilot PN offset index P2, and is called 30

Channel 2. 31

2. For each band class that the mobile station supports, configure the mobile station 32

to operate in that band class and perform steps 3 through 9. 33

3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps. 34

3GPP2 C.S0011-C v2.0

3-2

4. Send the overhead messages consecutively in synchronized message capsules on 1

the Primary Paging Channel of both base stations. Overhead message contents 2

shall be as specified in 6.5.2. 3

5. Set the test parameters for Test 1 as specified in Table 3.2.1.1.2-1. As specified in 4

Figure 3.2.1.1.2-1, the Channel 1 and Channel 2 pilot Ec/I0 levels shall transition 5

every 100 ms. 6

6. Set up a call using Fundamental Channel Test Mode 1 or 3 (see 1.3) and retrieve 7

the parameters PAG_1, PAG_2, PAG_4 and PAG_7, and then end the call. 8

7. Immediately after ending the call, run the test for at least 10 cycles (20 pilot Ec/I0 9

transitions). 10


the parameters PAG_1, PAG_2, PAG_4 and PAG_7, and then end the call. 12


Figure 3.2.1.1.2-2, the Channel 1 pilot Ec/I0 level shall transition between state 1 14

and state 2, where the state 1 duration is 5 seconds and the state 2 duration is 10 15

seconds. Repeat steps 6 through 8. 16

17

Table 3.2.1.1.2-1. Test Parameters for Idle Handoff in Non-Slotted Mode 18

Test 1 Test 2

Parameter Unit Channel 1 Channel 2 Channel 1 Channel 2

Îor /Ioc dB 3 for S1

0 for S2

0 for S1

3 for S2

3 for S1

-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7 -7 -7

orc

IEPaging

dB -12 -12 -12 -12

Ioc dBm/1.23 MHz -55 -55

0c

IEPilot

dB -10 for S1

-13 for S2

-13 for S1

-10 for S2

-10 for S1

-25 for S2 -13

Note: The Pilot Ec/I0 value is calculated from the parameters set in the table. It is not 19

a directly settable parameter. S1 and S2 indicate the two states of the power levels. 20

21

3GPP2 C.S0011-C v2.0

3-3

100 100 Time (ms)

Pilot Ec/I0 = -10 dBChannel 1

Pilot

Channel 2Pilot 3 dB

100 1

Figure 3.2.1.1.2-1. Idle Handoff in Non-Slotted Mode (Test 1) 2

3

10 5 Time (s)


PilotChannel 2

Pilot

3 dB

5

12 dB

4

Figure 3.2.1.1.2-2. Idle Handoff in Non-Slotted Mode (Test 2) 5

6

3.2.1.1.3 Minimum Standard 7

The number of idle handoffs during a test is given by ΔPAG_7, where ΔPAG_7 is the 8

increment of the parameter PAG_7 during the test. 9

The Paging Channel MER is estimated by 10

RATE_MSG4_PAG2_PAG1_PAG1MER

×ΔΔ−Δ

−= 11

where ΔPAG_1, ΔPAG_2, and ΔPAG_4 are the increment of parameters PAG_1, PAG_2 and 12

PAG_4 during the test, respectively, and MSG_RATE is the average number of messages 13

3GPP2 C.S0011-C v2.0

3-4

sent consecutively in a period of 20 half-frames1. MSG_RATE is equal to 5/20 when five 1

overhead messages are sent consecutively in synchronized message capsules2. If the base 2

stations cannot be configured to send this specified average message rate, then MSG_RATE 3

shall be the actual average message rate configured for the tests3. 4

Test 1: The mobile station should not perform any idle handoffs. The Paging Channel MER 5

shall be less than or equal to 0.1. 6

Test 2: The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 7

The Paging Channel MER shall be less than or equal to 0.1. 8

3.2.1.2 Idle Handoff in Slotted Mode on the Paging Channel 9

These tests shall be performed for mobile stations that can operate in slotted mode. 10


When in the Mobile Station Idle State, the mobile station searches for the strongest Pilot 12

Channel signal on the current CDMA frequency assignment during the assigned slots. The 13

mobile station determines that an idle handoff should occur when it detects a Pilot 14

Channel signal sufficiently stronger than the one it is currently monitoring. 15

This test verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 16


measured at the mobile station antenna connector, by measuring the number of idle 18

handoffs performed in a fixed period of time. 19






Channel 2. 25



3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps. 28

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the System Parameters Message (each slot 29

cycle is 1.28 seconds long). 30

1 All empty Paging Channel half-frames shall be filled with zeroes.

2 This requires that the General Page Message (see [6]) and Null Message (see [5]) are not sent.

3 In addition to the five overhead messages, up to one General Page Message (see [6]) and one or more Null Message (see [5]) may be sent.

3GPP2 C.S0011-C v2.0

3-5

5. Send the overhead messages consecutively on the Primary Paging Channel of both 1

Channel 1 and Channel 2. Overhead message contents shall be as specified in 2

6.5.2. 3

6. Send a General Page Message with no page records with the CLASS_0_DONE, 4

CLASS_1_DONE, TMSI_DONE, and BROADCAST_DONE fields set to ‘1’ at the 5

beginning of each assigned Paging Channel slot of the mobile station in every slot 6

cycle on the Primary Paging Channel of both Channel 1 and Channel 2. 7

7. Set the test parameters as specified in Table 3.2.1.2.2-1 and Figure 3.2.1.2.2-1. 8

8. Set up a call using Fundamental Channel Test Mode 1 or 3 (see 1.3), retrieve the 9

parameter PAG_7, and then end the call. 10

9. Run the test for exactly 20 Channel 1 pilot Ec/I0 transitions, starting and ending 11

with the Channel 1 pilot Ec/I0 at -25 dB. Allow three seconds after the last 12

transition before performing step 10. 13



16

Table 3.2.1.2.2-1. Test Parameters for Slotted Mode Idle Handoff 17

Parameter Unit Channel 1 Channel 2


-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

dB -12 -12

Ioc dBm/1.23 MHz -55

0c

IEPilot

dB -10 for S1

-25 for S2 -13

Note: The Pilot Ec/I0 value is calculated from the parameters 18

in the table. It is not a directly settable parameter. S1 and S2 19

indicate the two states of the power levels. 20

21

3GPP2 C.S0011-C v2.0

3-6

3 9 Time (s)

Pilot Ec/I0 = -13 dBChannel 1Pilot

Channel 2Pilot

3 dB

9

12 dB

1

Figure 3.2.1.2.2-1. Slotted Mode Idle Handoff 2

3




The number of idle handoffs shall be greater than or equal to 18. 7

3.2.1.3 Idle Handoff in Slotted Mode on the Forward Common Control Channel 8

These tests shall be performed for mobile stations that can operate in slotted mode and can 9

monitor the Forward Common Control Channel. 10



Channel signal on the current CDMA frequency assignment during the assigned slots. The 13

mobile station determines that an idle handoff should occur when it detects a Pilot 14

Channel signal sufficiently stronger than the one it is currently monitoring. 15

This test verifies that the mobile station performs an idle handoff whenever the Ec/I0 of a 16


measured at the mobile station antenna connector, by measuring the number of idle 18

handoffs performed in a fixed period of time. 19






Channel 2. 25



3GPP2 C.S0011-C v2.0

3-7

3. Set the Forward Common Control Channel data rate of Channel 1 and Channel 2 1

to 4800 bps. 2


cycle is 1.28 seconds long). 4

5. Send the overhead messages consecutively on the Forward Broadcast Control 5

Channel of both Channel 1 and Channel 2. Overhead message contents shall be as 6

specified in 6.5.2. 7

6. Send a General Page Message with no page records with the CLASS_0_DONE, 8


beginning of each assigned Forward Common Control Channel slot of the mobile 10

station in every slot cycle on the Forward Common Control Channel of both 11

Channel 1 and Channel 2. 12

7. Set the test parameters as specified in Table 3.2.1.3.2-1 and Figure 3.2.1.3.2-1. 13

8. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) if the mobile 14

station supports Radio Configuration 3 or 4, or set up a call using Fundamental 15

Channel Test Mode 7 (see 1.3) if the mobile station supports Radio Configuration 5 16

or 6, retrieve the parameter PAG_7, and then end the call. 17

9. Run the test for exactly 20 Channel 1 pilot Ec/I0 transitions, starting and ending 18

with the Channel 1 pilot Ec/I0 at -25 dB. Allow three seconds after the last 19

transition before performing continuing with step 10. 20

10. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) if the mobile 21

station supports Radio Configuration 3 or 4, or set up a call using Fundamental 22

Channel Test Mode 7 (see 1.3) if the mobile station supports Radio Configuration 5 23

or 6, retrieve the parameter PAG_7, and then end the call. 24

11. Set up a Quick Paging Channel associated with the Forward Common Control 25

Channel under test if the mobile station supports the Quick Paging Channel. Set 26

up the Sync Channel Message (or MC-MAP Sync Channel Message if 27

DIF_FREQ_PARAMS = ‘1’) and the MC-RR Parameters Message on the Broadcast 28

Control Channel to inform the mobile station of the existence of the Quick Paging 29

Channel with the Forward Common Control Channel. Repeat steps 4 through 10. 30

31

3GPP2 C.S0011-C v2.0

3-8

Table 3.2.1.3.2-1. Test Parameters for Slotted Mode Idle Handoff 1



-16.7 for S2

0 for S1

-4.7 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

dB -12 -12


0c

IEPilot

dB -10 for S1

-25 for S2 -13




5

3 9 Time (s)

Pilot Ec/I0 = -13 dBChannel 1Pilot

Channel 2Pilot

3 dB

9

12 dB

6

Figure 3.2.1.3.2-1. Slotted Mode Idle Handoff 7

8




The number of idle handoffs shall be greater than or equal to 18. 12

3GPP2 C.S0011-C v2.0

3-9

3.2.1.4 Idle Handoff to Another Frequency 1



Channel signal on the current CDMA frequency assignment. The mobile station determines 4

that an idle handoff should occur when it detects a Pilot Channel signal sufficiently 5

stronger than the one it is currently monitoring. However, there are system configurations 6

in which a neighbor base station cannot use the current CDMA frequency assignment. In 7

this case, the Extended Neighbor List Message or General Neighbor List Message may 8

contain the identity of a neighbor base station on a different CDMA frequency assignment. 9

The mobile station also searches this CDMA frequency assignment for this neighbor base 10

station. 11

The first test verifies that the mobile station quickly performs an idle handoff to a pilot in 12

the Neighbor Set which is on other than the current CDMA frequency assignment whenever 13

the Ec/I0 of all pilots in the Active Set and the Neighbor Set which are on the current 14

CDMA frequency assignment are less than some specified Ec/I0. 15

The second test verifies that the mobile station performs an idle handoff to a pilot in the 16

Neighbor Set which is on other than the current CDMA frequency assignment whenever the 17

Ec/I0 of all pilots in the Active Set and the Neighbor Set, which are on the current CDMA 18

frequency assignment, are less than some specified Ec/I0 and are less than the Ec/I0 of a 19

pilot in the Neighbor Set which is on other than the current CDMA frequency assignment. 20

The following tests are directly applicable to mobile stations that operate in the slotted 21

mode. For mobile stations that do not operate in the slotted mode, the same test 22

procedures apply, but the Audit Order shall be sent in any sequence of slots separated by 23

1.28 seconds. 24






Channel 2. Base station 1 uses arbitrary frequency f1, and base station 2 uses an 30

arbitrary but different frequency, f2. The frequency, f2, shall be a preferred 31

frequency with respect to system determination. 32



3. The number of Paging Channels should be the same for both Channel 1 and 35

Channel 2. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 36

bps. 37


cycle is 1.28 seconds long). Set GEN_NGHBR_LIST to 1 in the System Parameters 39

Message. 40

3GPP2 C.S0011-C v2.0

3-10

5. Send the overhead messages consecutively on the Primary Paging Channel of both 1

Channel 1 and Channel 2. Overhead message contents shall be as specified in 2

6.5.2 with the exception of the General Neighbor List Message. For Channel 1, the 3

General Neighbor List Message shall have the following field values: 4

5

Field Value (Decimal)

PILOT_INC 12 (768 chips)

NGHBR_SRCH_MODE 1 (search priorities included)

NGHBR_CONFIG_PN_INCL 1 (PN offsets included)

FREQ_FIELDS_INCL 1 (frequency included)

USE_TIMING 0 (hopping beacon timing off)

NUM_NGHBR 7 (seven neighbors)

NGHBR_CONFIG 0 (same as current)

NGHBR_PN P2

SEARCH_PRIORITY 1 (medium)

FREQ_INCL 1 (frequency included)

NGHBR_BAND x (where x is the band class)

NGHBR_FREQ f2

NGHBR_CONFIG 0

NGHBR_PN P3

SEARCH_PRIORITY 3 (very high)

FREQ_INCL 0 (frequency not included)

NGHBR_CONFIG 0

NGHBR_PN P4



NGHBR_CONFIG 0

NGHBR_PN P5



NGHBR_CONFIG 0

NGHBR_PN P6



NGHBR_CONFIG 0

NGHBR_PN P7

3GPP2 C.S0011-C v2.0

3-11




NGHBR_CONFIG 0

NGHBR_PN P8



1

For Channel 2, the General Neighbor List Message shall have the following field values: 2

3



NGHBR_SRCH_MODE 1 (search priorities included)

NGHBR_CONFIG_PN_INCL 1 (PN offsets included)

FREQ_FIELDS_INCL 1 (frequencies included)

USE_TIMING 0 (hopping beacon timing off)

NUM_NGHBR 7 (seven neighbors)

NGHBR_CONFIG 0 (same as current)

NGHBR_PN P1

SEARCH_PRIORITY 1 (medium)


NGHBR_BAND x (where x is the band class)

NGHBR_FREQ f1

NGHBR_CONFIG 0

NGHBR_PN P3


FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P4

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P5

SEARCH_PRIORITY 3

3GPP2 C.S0011-C v2.0

3-12


FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P6

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P7

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P8

SEARCH_PRIORITY 3

FREQ_INCL 0

1

6. Set the Channel 1 parameters to the maximum values for Test 1 in Table 3.2.1.4.2-2

1 (Îor/Ioc is equal to 0 dB). Set the Channel 2 parameters to the minimum values 3

for Test 1 in Table 3.2.1.4.2-1 (Îor/Ioc is equal to -18 dB). 4

7. Set up a call to the mobile station and retrieve the parameters PAG_3 and PAG_7, 5

and then end the call. 6

8. Send a General Page Message with no page records and with the CLASS_0_DONE, 7


beginning of each assigned Paging Channel slot of the mobile station on the 9

Channel 1 Primary Paging Channel. Send an Audit Order addressed to the mobile 10

station as a message requiring acknowledgement followed by a General Page 11

Message with no page records and with the CLASS_0_DONE, CLASS_1_DONE, 12

TMSI_DONE, and BROADCAST_DONE fields set to ‘1’ at the beginning of each 13

assigned Paging Channel slot of the mobile station on the Channel 2 Primary 14

Paging Channel. 15


Figure 3.2.1.4.2-1, the Channel 1 and Channel 2 levels shall transition every 2.56 17

seconds, which corresponds to every second assigned slot of the mobile station. 18

The levels shall transition after sending the General Page Message and before the 19

beginning of the next assigned slot. 20

10. Run the test for at least 10 cycles (20 pilot Ec/I0 transitions), ending with the 21

Channel 1 pilot Ec/I0 at -10 dB. 22



3GPP2 C.S0011-C v2.0

3-13

12. Set the Channel 1 parameters to the maximum values for Test 2 in Table 3.2.1.4.2-1

1 (Îor/Ioc is equal to 0 dB). Set the Channel 2 parameters to the minimum values 2

for Test 2 in Table 3.2.1.4.2-1 (Îor /Ioc is equal to -6 dB). 3


Figure 3.2.1.4.2-2, the Channel 1 and Channel 2 levels shall transition every 10.24 5

seconds, which corresponds to every eighth assigned slot of the mobile station. The 6

levels shall transition after sending the General Page Message and before the 7

beginning of the next assigned slot. 8

14. Run the test for at least 8 cycles (16 pilot Ec/I0 transitions), ending with the 9

Channel 1 pilot Ec/I0 at -10 dB. 10



13

Table 3.2.1.4.2-1. Test Parameters for Idle Handoff to Another Frequency 14

Test 1 Test 2

Parameter Unit Channel 1 Channel 2 Channel 1 Channel 2

Îor/Ioc dB Max = 0

Min = -18

Max = 0

Min = -18

Max = 0

Min = -6

Max = 0

Min = -6

orc

IEPilot dB -7 -7 -7 -7

orc

IEPaging dB -12 -12 -12 -12

Ioc dBm/1.23 MHz -75 -75

0c

IEPilot

dB Max = -10

Min = -25.1

Max = -10

Min = -25.1

Max = -10

Min = -14.0

Max = -10

Min = -14.0

t

bN

EPaging dB Max = 12.1

Min = -5.9

Max = 12.1

Min = -5.9

Max = 12.1

Min = 6.1

Max = 12.1

Min = 6.1

Note: The Pilot Ec/I0 and Paging Eb/Nt values are calculated from the parameters in 15

the table. These are not directly settable parameters. 16

17

3GPP2 C.S0011-C v2.0

3-14

AssignedPaging

Channel Slots

Mobile StationShould Receive AuditOrder Messages in

These Slots

2.56 2.56 Time (s)


Pilot

Channel 2Pilot 15.1 dB

2.56 1

Figure 3.2.1.4.2-1. Idle Handoff to Another Frequency (Test 1) 2

3

AssignedPaging Channel

Slots

Mobile StationShould ReceiveMessages in All

Slots

10.24 10.24 Time (s)


Pilot

Channel 2Pilot 4 dB

10.24 4

Figure 3.2.1.4.2-2. Idle Handoff to Another Frequency (Test 2) 5

6

3GPP2 C.S0011-C v2.0

3-15




The number of Audit Orders that were correctly received on Channel 2 during a test is given 4

by ΔPAG_3, where ΔPAG_3 is the increment of the parameter PAG_3 during the test. 5

Test 1: Since the change in pilot power level occurs when the mobile station is operating in 6

slotted mode, it is possible that the mobile station will miss messages sent in the first slot 7

after the transition. However, the mobile station shall receive messages in the second slot 8

after the transition. 9

The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 10

The number of Audit Orders that were correctly received shall be at least one half the 11

number of pilot Ec/I0 transitions. If the transition occurs sufficiently before the first slot, 12

then the number of Audit Orders that a mobile station not operating in the slotted mode 13

should have correctly received is equal to the number of pilot Ec/I0 transitions. 14

Test 2: Since the levels are sufficient to correctly receive messages on both Channel 1 and 15

Channel 2, the mobile station shall receive messages in all assigned slots. The mobile 16

station shall perform idle handoffs to the frequency with the stronger pilot. 17

The number of idle handoffs shall be equal to the number of pilot Ec/I0 transitions. 18

The number of Audit Orders that were correctly received shall be equal to four times the 19

number of pilot Ec/I0 transitions. 20

3.2.2 Soft Handoff Tests 21

3.2.2.1 Neighbor Set Pilot Detection and Incorrect Detection in Soft Handoff 22


This test measures the detection time for a pilot in the Neighbor Set at three values of pilot 24

Ec/I0, for the static add threshold test configuration. The detection time of a pilot is defined 25

as the time elapsed from the time when the pilot increases to a given Ec/I0 until the mobile 26

station sends a Pilot Strength Measurement Message or Extended Pilot Strength Measurement 27

Message containing this pilot. The accuracy of the Candidate Set pilot PN phase reported in 28

the corresponding Pilot Strength Measurement Message or Extended Pilot Strength 29

Measurement Message is also examined. 30

The correct detection of a pilot in the Neighbor Set is defined as the acquisition of a pilot 31

with Ec/I0 above the value defined by T_ADD. The value of T_ADD is set to 28 (-14 dB) as 32

specified in 6.5.2. An incorrect detection of a pilot in the Neighbor Set is defined as the 33

acquisition of a pilot with Ec/I0 below the value defined by T_ADD. 34





3GPP2 C.S0011-C v2.0

3-16


Channel 2. 2



3. Set up a call using Fundamental Channel Test Mode 1 or 3 or Dedicated Control 5

Channel Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 4 6

through 10. 7

4. Set the value of T_TDROP in the System Parameters Message to 1 (1 second). 8

5. Set the base station so as to not send any Extended Handoff Direction Message or 9

General Handoff Direction Message as a response to the Pilot Strength Measurement 10

Message or Extended Pilot Strength Measurement Message sent by the mobile 11

station. 12

6. Set the test parameters for Test 1 as specified in Table 3.2.2.1.2-1 and change the 13

pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-1 with T equal to 0.8 14

seconds. 15

7. Send the Pilot Measurement Request Order as specified in Figure 3.2.2.1.2-1. 16

8. Record the transmission time and contents of each Pilot Strength Measurement 17


station. 19


pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-1 with T equal to 0.85 21

seconds. Repeat steps 7 and 8. 22


pilot strength of Channel 2 as specified in Figure 3.2.2.1.2-2 with T equal to 15 24

seconds. Repeat steps 7 and 8 for 20 cycles of Channel 2 Pilot Ec/I0. 25

26

3GPP2 C.S0011-C v2.0

3-17

Table 3.2.2.1.2-1. Test Parameters for Neighbor Set Pilot Detection (Test 1) 1


Îor/Ioc dB 1.4 for S1

-1.8 for S2

0.4 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -12 for S1

−∞ for S2

Note: The Pilot Ec/I0 value is calculated from the parameters in the 2

table. It is not a directly settable parameter. S1 and S2 indicate the two 3

states of the power levels. 4

5

Table 3.2.2.1.2-2. Test Parameters for Neighbor Set Pilot Detection (Test 2) 6


Îor/Ioc dB 0.22 for S1

-1.8 for S2

-2.3 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -13.5 for S1

−∞ for S2




10

3GPP2 C.S0011-C v2.0

3-18

Table 3.2.2.1.2-3. Test Parameters for Neighbor Set Pilot Incorrect Detection 1

(Test 3) 2


Îor/Ioc dB -0.9 for S1

-1.8 for S2

-6.4 for S1

−∞ for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -11 -16.5 for S1

−∞ for S2




6

4 1 T

Pilot Ec/Io

Channel 1 Pilot

T_ADD

Time (s)

T_DROP

Channel 2 Pilot

Pilot MeasurementRequest Order

7

Figure 3.2.2.1.2-1. Neighbor Set Pilot Detection 8

9

3GPP2 C.S0011-C v2.0

3-19

4 1 T

Pilot Ec/Io

Channel 1 Pilot

T_ADD

Time (s)

T_DROP

Channel 2 Pilot

Pilot MeasurementRequest Order

1

Figure 3.2.2.1.2-2. Neighbor Set Pilot Incorrect Detection 2

3


Pilots other than P1 or P2 shall not be reported in any Pilot Strength Measurement Message 5

or Extended Pilot Strength Measurement Message. 6

Test 1: 7

1. The rate of valid detection within 0.8 seconds shall be greater than 90% with 95% 8

confidence (see 6.6). 9

2. All of the transmissions of Pilot Strength Measurement Message or Extended Pilot 10

Strength Measurement Message sent as a response to the Pilot Measurement 11

Request Order shall only contain P1. 12

3. The reported pilot PN phase for P2 in the Pilot Strength Measurement Message or 13

Extended Pilot Strength Measurement Message in which it is contained shall be no 14

greater than ±1 chip from the actual offset. 15

Test 2: 16

The rate of valid detection within 0.85 seconds shall be greater than 50% with 95% 17


Test 3: 19

There shall be no more than one Pilot Strength Measurement Message or Extended Pilot 20

Strength Measurement Message containing P2 during the test. 21

3GPP2 C.S0011-C v2.0

3-20

3.2.2.2 Candidate Set Pilot Detection and Incorrect Detection in Soft Handoff 1


This test measures the detection time for a pilot in the Candidate Set for the static 3

comparison threshold test configuration. The detection time of a pilot is defined as the time 4

elapsed from the time when the pilot increases to a given Ec/I0 until the mobile station 5

sends a Pilot Strength Measurement Message or Extended Pilot Strength Measurement 6

Message containing this pilot. The accuracy of the Active Set pilot PN phase reported in the 7

corresponding Pilot Strength Measurement Message or Extended Pilot Strength Measurement 8

Message is also examined. 9

The correct detection of a pilot in the Candidate Set is defined as the detection of a pilot in 10

the Candidate Set with Ec/I0 at least 0.5 x T_COMP dB above the Ec/I0 of an Active Set 11

pilot. The value of T_COMP is set to 5 (i.e. 0.5 x T_COMP = 2.5 dB) as specified in 6.5.2. An 12

incorrect detection of a pilot in the Candidate Set is defined as the detection of a pilot with 13

Ec/I0 less than 0.5 x T_COMP dB above the Ec/I0 of any Active Set pilot. 14






Channel 2. 20





through 8. 25




station. 29


pilot strength of Channel 2 as specified in Figure 3.2.2.2.2-1. 31

6. Send the Universal Handoff Direction Message listing only pilot P1 as specified in 32

Figure 3.2.2.2.2-1. 33



station. 36


pilot strength of Channel 2 as specified in Figure 3.2.2.2.2-2. 38

9. Set up a call using the current test mode. 39

3GPP2 C.S0011-C v2.0

3-21

10. Send the Universal Handoff Direction Message listing only pilot P1 as specified in 1

Figure 3.2.2.2.2-2. 2



station. 5

6

Table 3.2.2.2.2-1. Test Parameters for Candidate Set Pilot Detection (Test 1) 7



-4.8 for S2

-0.1 for S1

-4.8 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -14 -11 for S1

-14 for S2




11

Table 3.2.2.2.2-2. Test Parameters for Candidate Set Pilot Incorrect Detection 12

(Test 2) 13



-3.0 for S2

-0.5 for S1

-3.0 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -13 -11.5 for S1

-13 for S2




3GPP2 C.S0011-C v2.0

3-22

1

4 1 2.5

Pilot Ec/Io

Pilot ComparisonThreshold

Time (s)

Channel 2 Pilot

Universal HandoffDirection Message

Channel 1 Pilot

0.5 × T_COMP dB

2

Figure 3.2.2.2.2-1. Candidate Set Pilot Detection (Test 1) 3

4

4 1 2.5

Pilot Ec/Io

Time (s)

Channel 2 Pilot

Channel 1 Pilot

4 1


0.5 × T_COMP dB

Pilot ComparisonThreshold

5

Figure 3.2.2.2.2-2. Candidate Set Pilot Incorrect Detection (Test 2) 6

7

3GPP2 C.S0011-C v2.0

3-23


Test 1: 2

1. The rate of correct detection within 2.5 seconds shall be greater than 90% with 3

95% confidence (see 6.6). 4




Test 2: The probability that a Pilot Strength Measurement Message or Extended Pilot Strength 8

Measurement Message will be sent containing P2 within 2.5 seconds is 20% or less with 9


3.2.2.3 Active Set Pilot Loss Detection in Soft Handoff 11


This test measures the loss detection time for a diminishing pilot in the Active Set for the 13

static drop threshold test configuration. The loss detection time for a diminishing pilot in 14

the Active Set is defined as the time elapsed from the time when the pilot decreases to a 15

given Ec/I0 until the mobile station sends a Pilot Strength Measurement Message or 16

Extended Pilot Strength Measurement Message which flags this pilot for deletion from the 17

active set. The accuracy of the PN phase and strength of Active Set pilots reported in the 18

Pilot Strength Measurement Message or Extended Pilot Strength Measurement Message is also 19

examined. 20

The mobile station sends a Pilot Strength Measurement Message or Extended Pilot Strength 21

Measurement Message when the pilot Ec/I0 value of a pilot in the Active Set drops below 22

the value defined by T_DROP for a period of time defined by T_TDROP. The value of 23

T_DROP is set to 32 (i.e. 0.5 x T_DROP = -16 dB) as specified in 6.5.2. The value of 24

T_TDROP is set to 3 (4 seconds) for Test 1, and T_TDROP is set to 2 (2 seconds) for Test 2. 25






Channel 2. 31





through 10. 36



3GPP2 C.S0011-C v2.0

3-24


station. 2

5. Send a Universal Handoff Direction Message to the mobile station, specifying the 3

following pilots in the Active Set: 4

5

Parameter Value (Decimal)

PILOT_PN P1

PILOT_PN P2

6

6. Set the test parameters for Test 1 as specified in Table 3.2.2.3.2-1. Set the value of 7

T_TDROP to 3 (4 seconds) as specified in 6.5.2. 8

7. Record Reverse Traffic Channel messages for 5 minutes. 9

8. Set the test parameters for Test 2 as specified in Table 3.2.2.3.2-2 and Figure 10

3.2.2.3.2-1. Set the value of T_TDROP to 2 (2 seconds). 11

9. Send a Universal Handoff Direction Message to the mobile station as specified in 12

Figure 3.2.2.3.2-1, with the following pilots in the Active Set: 13

14


PILOT_PN P1

PILOT_PN P2

15



station. 18

19

3GPP2 C.S0011-C v2.0

3-25

Table 3.2.2.3.2-1. Test Parameters for Active Set Pilot Incorrect Loss Detection (Test 1

1) 2


Îor/Ioc dB -0.5 -4.5

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 -7


0c

IEPilot

dB -11 -15


table. It is not a directly settable parameter. 4

5

Table 3.2.2.3.2-2. Test Parameters for Active Set Pilot Loss Detection (Test 2) 6



2.9 for S2

-7.0 for S1

2.9 for S2

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 -7


0c

IEPilot

dB -11 -17 for S1

-11 for S2




10

3GPP2 C.S0011-C v2.0

3-26

6 2

Pilot Ec/Io

Time (s)

Channel 1 Pilot


1

T_DROP

T_ADD

Channel 2 Pilot

1

Figure 3.2.2.3.2-1. Active Set Pilot Loss Detection (Test 2) 2

3


Test 1: 5

The mobile station shall not send any Pilot Strength Measurement Message or 6

Extended Pilot Strength Measurement Message during the test. 7

Test 2: 8

1. The rate of loss detection within 6 seconds shall be greater than 80% with 95% 9





3. The reported pilot Ec/I0 value for P1 and P2 in the Pilot Strength Measurement 14

Message or Extended Pilot Strength Measurement Message shall be no greater than 15

±1.5 dB from their set values. 16

3.2.3 Access and Access Probe Handoff Tests 17

3.2.3.1 Access Probe Handoff 18


The mobile station is permitted to perform an access probe handoff when the mobile 20

station is in the Page Response Substate or the Mobile Station Origination Attempt Substate. 21

3GPP2 C.S0011-C v2.0

3-27

The correct detection of a pilot while in the System Access State is defined as the detection 1

of a pilot in the ACCESS_HO_LIST with Ec/I0 above the value defined by T_ADD. The value 2

of T_ADD is set to 28 (-14 dB) as specified in 6.5.2. An incorrect detection of a pilot while in 3

the System Access State is defined as the detection of a pilot in the ACCESS_HO_LIST with 4

Ec/I0 below the value defined by T_ADD. 5


1. Connect two base stations to the mobile station antenna connector as shown in 7

Figure 6.5.1-3. The AWGN source is not used in this test. The Forward Channel 8

from base station 1 has an arbitrary pilot PN offset index P1, and is called Channel 9

1. The Forward Channel from base station 2 has an arbitrary pilot PN offset index 10

P2, and is called Channel 2. 11



3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps for Test 14

1. 15

4. Ensure that P2 is the first pilot listed in the Neighbor List Message, Extended 16

Neighbor List Message, General Neighbor List Message or Universal Neighbor List 17

Message sent on Channel 1. 18

5. Set the following parameters in the Extended System Parameters Message: 19

20

Parameters Value (Binary)

NGHBR_SET_ENTRY_INFO 0 (Access entry handoff is disabled)

NGHBR_SET_ACCESS_INFO 1 (Base station is including info on neighbor set access probe

handoff or access handoff)

ACCESS_HO 0 (Disabled)

ACCESS_PROBE_HO 1 (Enabled)

ACC_HO_LIST_UPD 0 (No access probe handoffs are allowed to pilots not listed in

ACCESS_HO_LIST)

MAX_NUM_PROBE_HO 0 (Only one access probe handoff during this access attempt test is

allowed)

NGHBR_SET_SIZE 1 (P2 is the first and only pilot to be listed)

ACCESS_HO_ALLOWED 1 (An access probe handoff to P2 is allowed)

21

3GPP2 C.S0011-C v2.0

3-28

6. Set the test parameters as specified in Table 3.2.3.1.2-1. 1

2

Table 3.2.3.1.2-1. Test Parameters for Access Probe Handoff 3


Îor dBm/1.23 MHz -55 -58 for S1

-45 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

or

or

cI

E FCCCH

dB -12 -12

0c

IEPilot

dB -8.8 for S1 -17.4 for S2

-11.8 for S1 -7.4 for S2




7

7. Set base station 1 to ignore all access attempts. 8

8. Page the mobile station from base station 1 as specified in Figure 3.2.3.1.2-1. 9

9. After power is detected in an access probe from the mobile station as specified in 10

Figure 3.2.3.1.2-1, adjust the power of channel 2 to –45 dBm/1.23 MHz, the state 11

2 value specified in Table 3.2.3.1.2-1. 12

10. Monitor mobile station transmissions for at least 4 seconds after the adjustment of 13

Channel 2 power to state 2. Perform at least 11 trials. 14

11. If the mobile station supports the Forward Common Control Channel, set the 15

Forward Common Control Channel data rate of Channel 1 and Channel 2 to 9600 16

bps with 20 ms frame length for Test 2. Repeat steps 4 through 10. 17

18

3GPP2 C.S0011-C v2.0

3-29

1

Figure 3.2.3.1.2-1. Access Probe Handoff 2

3


For both Test 1 and Test 2: 5

1. The reported pilot PN phase for P2 in the Page Response Message sent prior to the 6

access probe handoff shall be no greater than ±1 chip from the actual offset for all 7

trials. If the mobile station supports access probe handoff, the reported pilot PN 8

phase for P1 in the Page Response Message sent after the access probe handoff 9

shall also be no greater than ±1 chip from the actual offset for all trials. 10

2. Valid detection of P2 prior to the access probe handoff shall occur in 90% of the 11

trials with 95% confidence (see 6.6). 12

3. If the mobile station supports access probe handoff, the probability that the mobile 13

station sends an access probe to base station 2 no later than 4 seconds after the 14

transition from state 1 to state 2 shall occur in 90% of the trials with 95% 15

confidence (see 6.6). The mobile station shall send all access probes to base station 16

2 using the appropriate coding for base station 2. 17

Pilot Ec/Io

Time (s)

General PageMessage

Channel 1Pilot

Channel 2Pilot

Page ResponseMessage to Base

Station 1

4


Station 2

Base Station 1detects

access probe

3GPP2 C.S0011-C v2.0

3-30

3.2.3.2 Access Handoff 1


The mobile station is permitted to perform an access handoff to receive the Paging Channel 3

or Forward Common Control Channel with the best pilot strength and an associated Access 4

Channel or Enhanced Access Channel, respectively. The mobile station is permitted to 5

perform an access handoff when waiting for a response from the base station or before 6

sending a response to the base station. An access handoff is permitted after an access 7

attempt while the mobile station is in the Page Response Substate or the Mobile Station 8

Origination Attempt Substate. 9

The value of T_ADD is set to 28 (-14 dB) as specified in 6.5.2. 10



Figure 6.5.1-3. The AWGN source is not used in this test. The Forward Channel 13

from base station 1 has an arbitrary pilot PN offset index P1, and is called Channel 14

1. The Forward Channel from base station 2 has an arbitrary pilot PN offset index 15




3. Set the Paging Channel data rate of Channel 1 and Channel 2 to 4800 bps for Test 19

1. 20

4. Ensure that P2 is the first pilot listed in the Neighbor List Message, Extended 21

Neighbor List Message, General Neighbor List Message, or Universal Neighbor List 22

Message sent on Channel 1. 23

5. Set the following parameters in the Extended System Parameters Message: 24

25

3GPP2 C.S0011-C v2.0

3-31

Parameters Value (Binary)

NGHBR_SET_ENTRY_INFO 0 (Access entry handoff is disabled)

NGHBR_SET_ACCESS_INFO 1 (Base station is including information on neighbor set

access probe handoff or access handoff)

ACCESS_HO 1 (Enabled)

ACCESS_HO_MSG_RSP 1 (Mobile station is permitted to perform an access handoff after receiving a message and before

responding to that message)

ACCESS_PROBE_HO 0 (disabled)

NGHBR_SET_SIZE 1 (P2 is the first and only pilot to be listed)

ACCESS_HO_ALLOWED 1 (An access handoff to P2 is allowed)

1

6. Set the test parameters as specified in Table 3.2.3.2.2-1. 2

3

Table 3.2.3.2.2-1. Test Parameters for Access Handoff 4


Îor dBm/1.23 MHz -55 -58 for S1

-45 for S2

orc

IEPilot dB -7 -7

orc

IEPaging

or

or

cI

E FCCCH

dB -12 -12

0c

IEPilot

dB -8.8 for S1 -17.4 for S2

-11.8 for S1 -7.4 for S2




8

3GPP2 C.S0011-C v2.0

3-32

7. Set base station 1 to acknowledge an access attempt without assigning a channel. 1

8. Page the mobile station from base station 1 as specified in Figure 3.2.3.2.2-1. 2

9. After the Page Response Message is received and an acknowledgement is sent on 3

Channel 1 as specified in Figure 3.2.3.2.2-1, adjust the power of channel 2 to –45 4

dBm/1.23 MHz, the state 2 value specified in Table 3.2.3.2.2-1. 5

10. Set base station 2 to send a single Channel Assignment Message or Extended 6

Channel Assignment Message to the mobile station four seconds after the transition 7

from state 1 to state 2. 8

11. Verify the mobile station completes the call on base station 2 for each trial. Perform 9

at least 11 trials. 10

12. If the mobile station supports the Forward Common Control Channel, set the 11

Forward Common Control Channel data rate of Channel 1 and Channel 2 to 9600 12

bps with 20 ms frame length for Test 2. Repeat steps 4 through 11. 13

14

15

Figure 3.2.3.2.2-1. Access Handoff 16

17


For both Test 1 and Test 2: 19

1. The reported pilot PN phase for P2 in the Page Response Message sent prior to the 20

access handoff shall be no greater than ±1 chip from the actual offset for all trials. 21

Pilot Ec/Io

Time (s)

General PageMessage

Channel 1Pilot

Channel 2Pilot


Station 1

4

Base Station 2 sendssingle Channel

Assignment Message

Base Station 1acknowledgesaccess probe

3GPP2 C.S0011-C v2.0

3-33

2. Valid detection of P2 prior to the access handoff shall occur in 90% of the trials with 1


3. The mobile station shall complete the call on base station 2 in 90% of the trials with 3


3.2.4 Candidate Frequency Single Search 5

3.2.4.1 Definition 6

This test measures the correct detection of a pilot in the Candidate Frequency Neighbor 7

Set. Correct detection is defined as the reporting of a pilot with Ec/I0 above the value 8

defined by CF_T_ADD. The value of CF_T_ADD is set to 28 (-14 dB). An incorrect detection 9

of a pilot in the Candidate Frequency Neighbor Set is defined as the reporting of a pilot with 10

Ec/I0 below the value defined by CF_T_ADD. 11

The base station directs the mobile station to perform a single search of the Candidate 12

Frequency Search Set by sending a Candidate Frequency Search Request Message. The 13

mobile station reports the search results to the base station in the Candidate Frequency 14

Search Report Message. The accuracy of the reported pilot PN phases is also examined. 15

3.2.4.2 Method of Measurement 16


Figure 6.5.1-3. The Forward Channel for base station 1 has a CDMA frequency 18

assignment F1 (any valid value), an arbitrary pilot PN offset index P1, and is called 19

Channel 1. The Forward Channel for base station 2 has a CDMA frequency 20

assignment F2 (any valid value other than F1), an arbitrary pilot PN offset index 21




3. If the mobile station supports demodulation of Radio Configuration 1 or 2, set up a 25

call on Channel 1 using Fundamental Channel Test Mode 1 (see 1.3) with 9600 bps 26

data rate only and perform steps 6 through 9. 27

4. If the mobile station supports demodulation of Radio Configuration 3, 4, or 5, set 28

up a call on Channel 1 using Fundamental Channel Test Mode 3 or Dedicated 29

Control Channel Test Mode 3 (see 1.3) with 9600 bps data rate only and perform 30

steps 6 through 9. 31

5. If the mobile station supports demodulation of Radio Configuration 6, 7, 8, or 9, 32

set up a call on Channel 1 using Fundamental Channel Test Mode 7 or Dedicated 33



6. Set the test parameters for Test 1 as specified in Table 3.2.4.2-1. 36

7. Send a Candidate Frequency Search Request Message to the mobile station to set 37

an explicit action time with the following parameters: 38

39

3GPP2 C.S0011-C v2.0

3-34

Parameters Value (Decimal)

USE_TIME 1 (use action time)

SEARCH_TYPE 1 (single search)

SEARCH_MODE 0 (CDMA)

CDMA_FREQ F2

SF_TOTAL_EC_THRESH 31 (disabled)

SF_TOTAL_EC_IO_THRESH 31 (disabled)

CF_SRCH_WIN_N 8 (60 chips)

CF_T_ADD 28 (-14 dB)

NUM_PILOTS 1 (1 pilot)

CF_NGHBR_SRCH_MODE 0 (no search priorities or search windows specified)

NGHBR_PN P2

1

8. Record the transmission time and contents of each Candidate Frequency Search 2

Report Message sent by the mobile station. Perform at least 30 trials. 3

9. Set the test parameters for Test 2 as specified in Table 3.2.4.2-2. 4

10. Send a Candidate Frequency Search Request Message to the mobile station as 5

described in step 7. 6

11. Record the transmission time and contents of each Candidate Frequency Search 7

Report Message sent by the mobile station. Perform at least 60 trials. 8

9

Table 3.2.4.2-1. Test Parameters for Candidate Frequency Neighbor Set Pilot 10

Detection (Test 1) 11


Îor/Ioc dB 0 -2.6

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -10 -11.5



3GPP2 C.S0011-C v2.0

3-35

1

Table 3.2.4.2-2. Test Parameters for Candidate Frequency Neighbor Set Pilot 2

Incorrect Detection (Test 2) 3


Îor/Ioc dB 0 -9.5

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7 N/A


0c

IEPilot

dB -10 -17



6

3.2.4.3 Minimum Standard 7

Test1: 8

1. No pilot other than P2 shall be reported in any Candidate Frequency Search Report 9

Message for all trials. 10

2. Correct detection of P2 shall occur in 90% of the trials with 95% confidence (see 11

6.6). 12

3. The reported pilot PN phase for P2 in the Candidate Frequency Search Report 13

Message shall be no greater than ± 1 chip from the actual offset for all trials. 14

Test 2: 15

Incorrect detection of P2 shall occur in less than 5% of the trials with 95% confidence 16

(see 6.6). 17

3.3 Forward Common Channel Demodulation Performance 18

The mobile station receiver shall be capable of detecting the signal defined in Section 3.1 of 19

[4]. 20

3.3.1 Demodulation of Non-Slotted Mode Paging Channel 21

These tests shall be performed for mobile stations that can operate in non-slotted mode 22

while in the Mobile Station Idle State. 23

3GPP2 C.S0011-C v2.0

3-36


The performance of the demodulation of Paging Channel in an AWGN (no fading or 2

multipath) environment is determined by the message error rate (MER). The MER is 3

measured only for 9600 bps data rate. 4


1. Connect the base station and an AWGN noise source to the mobile station antenna 6

connector as shown in Figure 6.5.1-4. 7



3. Set the Paging Channel data rate to 9600 bps. 10

4. Set the test parameters as specified in Table A.1.1.1-1. 11

5. Send the overhead messages consecutively in synchronized message capsules on 12

the Primary Paging Channel. Overhead message contents shall be as specified in 13

6.5.2. 14


the parameters PAG_1, PAG_2 and PAG_4 and then end the call. 16

7. Run the test for at least 5 seconds and until sufficient confidence is ensured. 17


the parameters PAG_1, PAG_2 and PAG_4. 19


The actual Eb/Nt used in the test shall be within ±0.2 dB of the value indicated in Table 21

A.1.1.2-1. 22

The Paging Channel MER is estimated by 23

RATE_MSG4_PAG2_PAG1_PAG1MER

×ΔΔ−Δ

−= 24

where ΔPAG_1, ΔPAG_2, and ΔPAG_4 are the increment of parameters PAG_1, PAG_2 and 25

PAG_4 during the test, respectively, and MSG_RATE is the average number of messages 26

sent consecutively in a period of 10 half-frames4. MSG_RATE is equal to 5/10 when five 27

overhead messages are sent consecutively in synchronized message capsules5. If the base 28

stations cannot be configured to send this specified average message rate, then MSG_RATE 29

shall be the actual average message rate configured for the tests6. 30

4 All empty Paging Channel half-frames shall be filled with zeroes.

5 This requires that the General Page Message (see [6]) and Null Message (see [5]) are not sent.

6 In addition to the five overhead messages, up to one General Page Message (see [6]) and one or more Null Message (see [5]) may be sent.

3GPP2 C.S0011-C v2.0

3-37

The MER shall not exceed the piece-wise linear MER curve specified by the points in Table 1

A.1.1.2-1 with 95% confidence (see 6.6). 2

3.3.2 Demodulation of Slotted Mode Paging Channel 3

This test shall be performed for mobile stations that can operate in slotted mode. If the 4

mobile station supports the Quick Paging Channel, then this test shall be performed with 5

the Quick Paging Channel enabled. 6


When operating in the slotted mode, the mobile station starts monitoring the Paging 8

Channel at the beginning of the assigned slots. If the mobile station supports the Quick 9

Paging Channel, the mobile station checks its assigned paging indicators in the Quick 10

Paging Channel slot immediately preceding its assigned Paging Channel slot. If the paging 11

indicators are set to “ON”, the mobile station is to receive the Paging Channel in the 12

assigned Paging Channel slot following its assigned Quick Paging Channel slot. 13

These tests verify that the mobile station wakes up in time so that it does not miss the 14

beginning of its assigned slots. If the mobile station supports the Quick Paging Channel, 15

these tests verify that when the mobile station receives its Quick Paging Channel indicators 16

in strong or weak channel test conditions, the mobile station still monitors its assigned 17

Paging Channel slot. 18

This test also examines the demodulation performance of the Paging Channel in an AWGN 19

(no fading or multipath) environment. The demodulation performance of the Paging 20

Channel is determined by the message error rate (MER). The MER is measured only for 21

9600 bps data rate. 22



connector as shown in Figure 6.5.1-4. Set the Paging Channel data rate to 9600 bps. 25

2. For each band class that the mobile station supports, configure the mobile station to 26

operate in that band class and perform steps 3 through 15. 27

3. For each Paging Channel spreading rate that the mobile station supports, perform steps 28

4 through 15. 29

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the ANSI-41 System Parameters Message (each 30

slot cycle is 1.28 seconds long). 31

5. If the mobile station supports the Quick Paging Channel, set the following values in the 32

Extended System Parameters Message: 33

34

3GPP2 C.S0011-C v2.0

3-38


QPCH_SUPPORTED 1 (QPCH enabled)

NUM_QPCH 1 (1 QPCH supported)

QPCH_RATE 0 (4800 bps)

QPCH_POWER_LEVEL_PAGE 2 (3 dB below the Pilot Channel Transmit Power)

1

6. If the mobile station supports the Quick Paging Channel, set both of the mobile 2

station’s paging indicators to “ON” for its assigned Quick Paging Channel slot in 3

every slot cycle. Set all other paging indicator bits to “OFF”, including all reserved 4

indicators. 5

7. Send the overhead messages consecutively on the Primary Paging Channel. 6

Overhead message contents shall be as specified in 6.5.2. 7

8. Send an Audit Order that does not require a layer 2 acknowledgment, addressed to 8

the mobile station, only at the beginning of each assigned Paging Channel slot of 9

the mobile station in every slot cycle. The order shall be part of an Order Message 10

with a length of 82 bits. Within the same slot as the Order Message, send a General 11

Page Message with no page records addressed to the mobile station and with the 12

CLASS_0_DONE, CLASS_1_DONE, TMSI_DONE, and BROADCAST_DONE fields 13

set to ‘1’. 14

9. Set the parameters for Test 1 as specified in Table A.1.2.1-1. 15



11. Run the test for at least two minutes and until sufficient confidence is ensured. 18


parameter PAG_3 and calculate the Paging Channel MER. 20

13. Set the parameters for Test 2 as specified in Table A.1.2.1-2 and repeat steps 10 21

through 12. 22


through 12. 24


through 12. 26


The actual Quick Paging and Paging Eb/Nt values used in the test shall be within ±0.2 dB 28

of the values indicated in Table A.1.2.1-1 through A.1.2.1-4. 29

The Paging Channel MER can be estimated by 30

3GPP2 C.S0011-C v2.0

3-39

PCH MER = 1 - 28.1/T

3_PAGΔ 1

where ΔPAG_3 is the increment of parameter PAG_3 during the test, and T is the length of 2

the test in seconds. 3

Alternatively, the Paging Channel MER can be measured by 4

PCH MER = 1 - N

3_PAGΔ 5

where ΔPAG_3 is the increment of parameter PAG_3 during the test, and N is the exact 6

number of paging channel messages sent by the base station that were addressed to the 7

mobile station under test. 8

If the mobile station supports the Spreading Rate 1 Paging Channel, the Paging Channel 9

MER shall not exceed the piece-wise linear MER curve specified by the points in Table 10

A.1.2.2-1 (for Test 1) and Table A.1.2.2-2 (for Test 2) with 95% confidence (see 6.6). 11

If the mobile station supports the Spreading Rate 3 Paging Channel, the Paging Channel 12

MER shall not exceed the piece-wise linear MER curve specified by the points in Table 13

A.1.2.2-3 (for Test 3) and Table A.1.2.2-4 (for Test 4) with 95% confidence (see 6.6). 14

3.3.3 Demodulation of Broadcast Control Channel in AWGN Channel 15

These tests shall be performed for mobile stations that support the Broadcast Control 16

Channel. 17


This test examines the demodulation performance of the Broadcast Control Channel in an 19

AWGN (no fading or multipath) environment. The demodulation performance of the 20

Broadcast Control Channel is determined by the frame error rate (FER). 21






3. For each Broadcast Control Channel spreading rate and code rate that the mobile 27

station supports, perform steps 4 through 11. 28

4. Send continuous messages on the Broadcast Control Channel in 40ms broadcast 29

slots (19200 bps). Overhead message contents shall be as specified in 6.5.2. 30

5. Set the test parameter values for each test as specified in Table A.1.3.1-1 through 31

A.1.3.1-3. 32

6. Set up a call using Fundamental Channel Test Mode 3 (see 1.3), retrieve the 33

parameters BCCH_6 and BCCH_9, and then end the call. 34

3GPP2 C.S0011-C v2.0

3-40

7. Have the base station increment either the CONFIG_MSG_SEQ or the 1

ACC_MSG_SEQ in the General Page Message sent on the F-CCCH on each paging 2

slot of the MS under test. 3

8. Run the test for at least seven minutes and 41 seconds and until sufficient 4

confidence is ensured. 5



10. Send continuous messages on the Broadcast Control Channel (see 6.5.2) in 80ms 8

broadcast slots (9600 bps) and repeat steps 5 through 9 using BCCH_7 instead of 9

BCCH_6. 10



BCCH_6. 13


The actual BCCH Eb/Nt values used in the test shall be within ±0.2 dB of the values 15

indicated in Table A.1.3.1-1 through A.1.3.1-3. 16

The Broadcast Control Channel FER is calculated by: 17

BCCH FER = 9_BCCHN_BCCH

9_BCCHΔ+Δ

Δ , 18

where ΔBCCH_9 is the increment of parameter BCCH_9 (i.e. insufficient physical layer 19

frame quality) during the test, and ΔBCCH_N is the increment of parameter BCCH_6, 20

BCCH_7, or BCCH_8 which is the appropriate counter for the successful demodulation of 21

the frame and coding structure being tested, and when added to the erased frames is the 22

total number of Broadcast Control Channel frames sent in the mobile station broadcast 23

slot during the test interval. 24

For each spreading rate and rate mode the mobile stations supports, the FER for each test 25

shall not exceed the piecewise linear FER curve specified by the points in Tables A.1.3.2-1 26

through A.1.3.2-3 with 95% confidence (see 6.6). 27

3.3.4 Demodulation of Broadcast Control Channel in Multipath Fading Channel 28


The performance of the demodulation of Broadcast Control Channel in multipath fading 30

channel with and without transmit diversity is determined by the frame error rate (FER). 31




3GPP2 C.S0011-C v2.0

3-41



3. For each Broadcast Control Channel spreading rate and code rate that the mobile 3

station supports, perform steps 4 through 12. 4

4. Send continuous messages on the Broadcast Control Channel in 40ms broadcast 5

slots (19200 bps). Overhead message contents shall be as specified in 6.5.2. 6

5. Set the test parameter values for each test as specified in Table A.1.4.1-1 through 7

A.1.4.1-20. 8



7. Have the base station increment either the CONFIG_MSG_SEQ or the 11

ACC_MSG_SEQ in the General Page Message sent on the F-CCCH on each paging 12

slot of the MS under test. 13






BCCH_6. 19



BCCH_6. 22

12. Repeat the test for each transmit diversity scheme (e.g. OTD or STS) supported by 23

the mobile station and set the following parameters in the Sync Channel Message: 24

25

Parameter Value (Binary)

SR1_TD_INCL ‘1’ (Transmit Diversity enabled)

SR1_TD_POWER_LEVEL ‘10’ (3 dB below the Forward Pilot Channel transmit power)

26


The actual power measurement uncertainty shall be less than or equal to 0.2 dB (see 6.6.2) 28

with the minimum test duration meeting the requirements specified in Table 6.6.2-1. Test 29

durations must be sufficient to meet confidence level requirements. 30

The actual BCCH Eb/Nt values used in the test shall be within ±0.2 dB of the values 31

indicated in Table A.1.4.1-1 through A.1.4.1-20. 32

The Broadcast Control Channel FER is calculated by: 33

3GPP2 C.S0011-C v2.0

3-42

BCCH FER = 9_BCCHN_BCCH

9_BCCHΔ+Δ

Δ , 1

where ΔBCCH_9 is the increment of parameter BCCH_9 (i.e. insufficient physical layer 2

frame quality) during the test, and ΔBCCH_N is the increment of parameter BCCH_6, 3

BCCH_7, or BCCH_8 and represents the appropriate counter for the successful 4

demodulation of the frame and coding structure being tested, and when added to the 5

erased frames is the total number of Broadcast Control Channel frames sent in the mobile 6

station broadcast slot during the test interval. 7

The FER for each test shall not exceed the piecewise linear FER curve specified by the 8

points in Tables A.1.4.2-1 through A.1.4.2-10 with 95% confidence (see 6.6). 9

3.3.5 Demodulation of Forward Common Control Channel 10

These tests shall be performed for mobile stations that support the Broadcast Control 11

Channel and the Forward Common Control Channel. The Quick Paging Channel shall be 12

disabled during these tests. 13


The performance of the demodulation of the Forward Common Control Channel in an 15

AWGN (no fading or multipath) environment is determined by the frame error rate (FER). 16






3. For each Forward Common Control Channel spreading rate and code rate that the 22

mobile station supports, perform steps 4 through 10. 23

4. Set MAX_SLOT_CYCLE_INDEX to 0 in the ANSI-41 System Parameters Message 24

(each slot cycle is 1.28 seconds long). 25

5. Send a General Page Message with no Page Records in the mobile station’s 26

assigned Forward Common Control Channel slot in every slot cycle. 27

6. Set the test parameters for each test as specified in Tables A.1.5.1-1 through 28

A.1.5.1-4. 29

7. Set up a call using Fundamental Channel Test Mode 3 (see 1.3) and retrieve the 30

parameters FCCCH_5 (tests 2, 5, 8, and 11), FCCCH_6 (tests 1, 4, 7, and 10), or 31

FCCCH_7 (tests 3, 6, 9, and 12), and FCCCH_11, and then end the call. 32

8. Run the test for at least seven minutes and 41 seconds and until sufficient 33

confidence is ensured. 34

3GPP2 C.S0011-C v2.0

3-43


parameters FCCCH_5 (tests 2, 5, 8, and 11), FCCCH_6 (tests 1, 4, 7, and 10), or 2

FCCCH_7 (tests 3, 6, 9, and 12), and FCCCH_11. 3


The actual power measurement uncertainty shall be less than or equal to 0.2 dB with the 5

minimum test duration meeting the power measurement uncertainty requirement. Test 6


The actual F-CCCH Eb/Nt used in each test shall be within ±0.2 dB of the value indicated 8

in A.1.5.1-1 through A.1.5.1-4. 9

The Forward Common Control Channel FER is calculated by: 10

F-CCCH FER = 11_FCCCHN_FCCCH

11_FCCCHΔ+Δ

Δ , 11

where ΔFCCCH_11 is the increment of parameter FCCCH_11 (i.e. insufficient physical layer 12

frame quality) during the test, and ΔFCCCH_N is the increment of the appropriate counter 13

for the successful demodulation of the frame and coding structure being tested, and when 14

added to the erased frames is the total number of Forward Common Control Channel 15

frames sent to the mobile station during the test. 16



3.3.6 Demodulation of Common Assignment Channel and Reception of Common Power 19

Control Channel 20

These tests shall be performed for mobile stations that support the Common Assignment 21

Channel and Common Power Control Channel. 22


When operating in the Reservation Access Mode, the mobile station monitors the Common 24

Assignment Channel after transmitting the preamble on the Enhanced Access Channel. 25

Once the Early Acknowledgement Channel Assignment Message is received, the mobile 26

station starts transmitting the access message on the Reverse Common Control Channel, 27

which is power controlled by the Common Power Control Channel. The following tests verify 28

that the mobile station has proper demodulation performance of the Common Assignment 29

Channel and reception of the Common Power Control Channel in an AWGN environment. 30

The performance of the demodulation of the Common Assignment Channel in an AWGN (no 31

fading or multipath) environment is determined by the frame error rate (FER). The 32

performance of the reception of the Common Power Control Channel is determined by the 33

compliance of the mobile station transmit power with the assigned power control 34

subchannel power control bits. 35

3GPP2 C.S0011-C v2.0

3-44






3. For each Common Assignment Channel spreading rate and code rate that the 6

mobile station supports, perform steps 4 through 13. 7

4. Set the following values in the Enhanced Access Parameters Message: 8

9


ACCESS_MODE 1 (Reservation Access Mode)

APPLICABLE_MODES 2 (Parameters are for Reservation Access Mode)

CACH_CODE_RATE As specified in the test

RA_PC_DELAY 4 (MS to ignore 4 PC bits after start of RCCCH transmission)

RCCCH_HO_SUPPORTED 0 (RCCCH handoff disabled)

CPCCH_RATE 2 (800 bps CPCCH power control rate)

RA_CPCCH_STEP_UP 2 (up step size is 1 dB)

RA_CPCCH_STEP_DN 2 (down step size is 1 dB)

NUM_PCSCH_RA 24 (24 Power Control Subchannels)

10

5. Send a Status Request Order on the Forward Common Control Channel. 11

6. Once the end of the header on the Enhanced Access Channel is detected, send an 12

Early Acknowledgement Channel Assignment Message on the Common Assignment 13

Channel addressed to the mobile station. 14

7. Send a periodic pattern of twenty ‘0’ power control bits followed by twenty ‘1’ power 15

control bits on the Common Power Control Subchannel assigned to the mobile 16

station. 17

8. Set the test parameter values as specified in Table A.1.6.1-1 through A.1.6.1-3. 18


parameter CACH_2, and then end the call. 20

10. Count, at the base station, the number of frames transmitted to the mobile station 21

on the Common Assignment Channel. 22

11. Monitor the mobile station transmission and its power level on the Reverse 23

Common Control Channel. 24

3GPP2 C.S0011-C v2.0

3-45



parameter CACH_2. 3





The actual CACH Eb/Nt and CPCCH Eb/Nt values used in the test shall be within ±0.2 dB 8

of the values indicated in Table A.1.6.1-1 through A.1.6.1-3. 9

The Common Assignment Channel FER is calculated by: 10

CACH FER = ansmitted_Frames_TrTotal_CACH

2_CACHΔ , 11

where ΔCACH_2 is the increment of parameter CACH_2 (i.e. insufficient physical layer 12

frame quality) during the test, and Total_CACH_Frames_Transmitted is the total number of 13

Common Assignment Channel frames sent to the mobile station during the test. 14



For all tests, the mobile station output power on the Reverse Common Control Channel, 17

measured at the mobile station antenna connector, shall have a periodic pattern. In each 18

period the power shall increase monotonically for a duration of 20 power control groups 19

and then decrease monotonically for a duration of 20 power control groups. 20

3.3.7 Demodulation of Forward Packet Data Control Channel in Additive White Gaussian 21

Noise 22

This test shall be performed on the Forward Packet Data Control Channel, if the Forward 23

Packet Data Control Channel is supported by the mobile station. 24


The demodulation performance of Forward Packet Data Control Channel in AWGN is 26

determined by the frame error rate (FER). The FER is calculated for each individual data 27

rate. 28

If the mobile station supports the Forward Fundamental Channel, then the base station 29

shall transmit the Forward Fundamental Channel, which will contain the power control 30

subchannel. Otherwise, the base station shall transmit the Forward Dedicated Control 31

Channel, which will contain the power control subchannel. The forward link closed loop 32

power control shall be disabled in the base station. The base station shall set the Forward 33

Packet Data Control Channel transmission format independent of the data received on the 34

Reverse Channel Quality Indicator Channel and the Reverse Acknowledgment Channel. 35

3GPP2 C.S0011-C v2.0

3-46


1. Connect the base station and an AWGN generator to the mobile station antenna 2




3. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). Configure the 6

base station to send fixed duration messages on the Forward Packet Data Control 7

Channel. Configure the base station to send the Forward Packet Data Control 8

Channel messages on the maximum number of ARQ Channels supported by the 9

mobile station with a duty cycle on those channels equal to 100%. Configure the 10

base station so that it sets the MAC_ID field to the value assigned to the mobile 11

station in all messages sent on the Forward Packet Data Control Channel. 12

4. Configure the base station to map the Layer 3 Signaling messages only onto the 13

Forward Fundamental Channel or Forward Dedicated Control Channel. 14

5. Set up the test parameters for each test as specified in 3.3.7.2-1. 15

6. Count, at the base station, the number of Forward Packet Data Control Channel 16

frames transmitted, and the number of Forward Packet Data Control Channel good 17

frames received at the mobile station. A good frame is one that passes the CRC 18

check and matches the mobile station’s assigned MAC_ID. 19

20

3GPP2 C.S0011-C v2.0

3-47

Table 3.3.7.2-1. Test Parameters for Forward Packet Data Control Channel in AWGN 1

Parameter Units Test 1 Test 2 Test 3

Îor/Ioc dB -1

orc

IE Pilot

dB -7

orc

IE Sync

dB -16

orc

IEPaging

dB -12

orc

IE FCH dB -16.2

orc

IE PDCCH dB

-11.2 -15.2 -18.5

Ioc dBm/1.23MHz -54

Data Rate bps 29600 (1.25ms) 14800 (2.5ms) 7400 (5ms)

tb

NE PDCCH dB

3.9 3.0 2.7

2





The actual Forward Packet Data Control Channel Eb/Nt used in each test shall be within 7

±0.2 dB of the value indicated in Table 3.3.7.2-1. 8


points in Table 3.3.7.3-1 with 95% confidence. 10

11

3GPP2 C.S0011-C v2.0

3-48

Table 3.3.7.3-1. Minimum Standards for Radio Configuration 10 Forward Packet Data 1

Control Channel Performance in AWGN 2

Test Data Rate [bps]

F-PDCCH Eb/Nt [dB] FER

3.0 0.05

1 29600 3.9 0.01

4.2 0.005

2.1 0.05

2 14800 3.0 0.01

3.2 0.005

1.9 0.05

3 7400 2.7 0.01

3.1 0.005

3

3.3.8 Demodulation of Forward Packet Data Control Channel in Soft and Softer Handoff 4


The mobile station indicates the selected serving sector with the R-CQICH cover. The 6

mobile station selects the serving sector based on the estimated pilot signal-to-noise ratio. 7

There are four tests. Test 1 and Test 2 verify the mobile station switches serving sector to 8

maintain data throughput. Test 1 verifies switching between co-located sectors (softer 9

switch). Test 2 verifies switching between non co-located sectors (soft switch). Tests 3 and 10

4 verify the mobile station does not switch serving sectors so fast that it does not receive 11

packets from any sector. Test 3 verifies switching between co-located sectors (softer 12

switch). Test 4 verifies handoff between non co-located sectors (soft switch). The 13

parameters PDCH_SOFT_SWITCHING_DELAY and PDCH_SOFTER_SWITCHING_DELAY 14

determine the time the base station will take to redirect data from one serving sector to 15

another. 16


1. Connect two base stations (two sectors) to the mobile station as shown in Figure 18

6.5.1.3. The Forward Channel from sector 1 has an arbitrary pilot PN offset index 19

P1, and is called Channel 1. The Forward Channel from sector 2 has an arbitrary 20

pilot PN offset index P2, and is called Channel 2. 21

2. Configure the mobile station to operate in a band class it supports. 22

3. Set the base station so as not to send any Extended Handoff Direction Message or 23

General Handoff Direction Message or Universal Handoff Direction Message as a 24

response to the Pilot Strength Measurement Message or Extended Pilot Strength 25

Measurement Message sent by the mobile station. 26

3GPP2 C.S0011-C v2.0

3-49

4. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). Set the test 1

parameters as specified in Table 3.3.8.2-1 and Figure 3.3.8.2-1. Configure each 2

base station to send one slot length messages on the Forward Packet Data Control 3

Channel. Configure each base station to send the Forward Packet Data Control 4

Channel messages on the maximum number of ARQ Channels supported by the 5

mobile station with a duty cycle on those channels equal to 100%. Configure each 6

base station to set the MAC_ID field to the value assigned to the mobile station in 7

all messages sent on the Forward Packet Data Control Channel while it is in state 8

S1; and to set the MAC_ID field to a value other than that assigned to the mobile 9

station in all messages sent on the Forward Packet Data Control Channel while it 10

is in state S2. 11

5. For Test 1, perform Steps 6 and 7. 12

6. Send an Extended Channel Assignment Message to the mobile station, specifying 13

the following parameters: 14

15


NUM_SOFT_SWITCHING_FRAMES 0 (1 frames)

NUM_SOFTER_SWITCHING_FRAMES 0 (1 frames)

PDCH_SOFT_SWITCHING_DELAY 15 (160 ms)

PDCH_SOFTER_SWITCHING_DELAY 0 (10 ms)

PILOT_PN P1

PWR_COMB_IND 0

PDCH_GROUP_IND 0

PILOT_PN P2

PWR_COMB_IND 1 (softer handoff)

PDCH_GROUP_IND 1 (softer reselection parameters)

16

7. Measure the Forward Packet Data Control Channel frame error rate. The duration 17

of the test shall be at least 1 minute. 18

8. For Test 2, perform Steps 9 and 10. 19

9. Send an Extended Channel Assignment Message to the mobile station, specifying 20

the following parameters: 21

22

3GPP2 C.S0011-C v2.0

3-50


NUM_SOFT_SWITCHING_FRAMES 0 (1 frames)

NUM_SOFTER_SWITCHING_FRAMES 0 (1 frames)

PDCH_SOFT_SWITCHING_DELAY 15 (160 ms)

PDCH_SOFTER_SWITCHING_DELAY 0 (10 ms)

PILOT_PN P1

PWR_COMB_IND 0

PDCH_GROUP_IND 0

PILOT_PN P2

PWR_COMB_IND 1 (softer handoff)

PDCH_GROUP_IND 0 (soft reselection parameters)

1

10. Measure the Forward Packet Data Control Channel frame error rate. The duration 2

of the test shall be at least 1 minute. 3

11. For Test 3, set the test parameters as specified in Table 3.3.8.2-1 and Figure 4

3.3.8.2-2 and repeat step 6. 5

12. Count at the mobile station, the number of cell switches performed. The duration 6

of the test shall be at least 5 seconds and no more than 30 seconds. 7

13. For Test 4, set the test parameters as specified in Table 3.3.8.2-1 and Figure 8

3.3.8.2-3, and repeat step 9. 9

14. Count at the mobile station, the number of cell switches performed. The duration 10

of the test shall be at least 30 seconds and no more than 90 seconds. 11

3GPP2 C.S0011-C v2.0

3-51

Table 3.3.8.2-1. Test Parameters for Forward Packet Data Channel Demodulation in 1

Soft and Softer Handoff 2

Test 1 and Test 2 Test 3 and Test 4 Parameter Units

Channel 1 Channel 2 Channel 1 Channel 2

ocor I/I dB 7 for S1

3 for S2

3 for S1

7 for S2

7 for S1

3 for S2

3 for S1

7 for S2

ocI dBm/1.23 MHz -55

orc

IE Pilot

dB -7 -7

oc

IE Pilot

dB -9 for S1

-13 for S2

-13 for S1

-9 for S2

-9 for S1

-13 for S2

-13 for S1

-9 for S2

orc

IE

PDCCH dB -7 -7

Note: The Pilot Ec/I0 value is calculated from the parameters set in the table. It is not a settable parameter itself. S1 and S2 indicate the two states of the power levels.

3

5 5 Time (s)

Pilot Ec/I0 = -9 dB

Channel 1Pilot

Channel 2Pilot 4 dB

5

4

5

Figure 3.3.8.2-1. Forward Packet Data Channel Demodulation in Softer and Soft 6

Handoff (Tests 1 and 2) 7

8

3GPP2 C.S0011-C v2.0

3-52

10 10 Time (ms)

Pilot Ec/I0 = -9 dB

Channel 1Pilot

Channel 2Pilot 4 dB

10

1

2

Figure 3.3.8.2-2. Forward Packet Data Channel Demodulation in Softer Handoff 3

(Test 3) 4

5

160 160 Time (ms)

Pilot Ec/I0 = -9 dB

Channel 1Pilot

Channel 2Pilot 4 dB

160

6

7

Figure 3.3.8-3. Forward Packet Data Channel Demodulation in Soft Handoff (Test 4) 8

9


For Test 1 and Test 2 calculate the Reverse Packet Data Control Channel FER. The FER 11

shall be calculated, for active frames only, as follows:

12

3GPP2 C.S0011-C v2.0

3-53

dtransmitteframesPDCCHofNumbercorrectlyreceivedframesPDCCHofNumber1FER −= 1

2

Test 1: 3

The average Forward Packet Data Control Channel FER shall be less than 7%7. 4

Test 2: 5

The average Forward Packet Data Control Channel FER shall be less than 15%8. 6

Test 3 and Test 4: 7

The mobile station shall not perform more than one cell switch during the test. 8

7 In the next revision of this Standard, a lower FER limit may be specified.

8 In the next revision of this Standard, a lower FER limit may be specified.

3GPP2 C.S0011-C v2.0

3-54

3.4 Forward Traffic Channel Demodulation Performance 1

The mobile station receiver shall be capable of detecting the signal defined in Section 3.1 of 2

[4]. 3

3.4.1 Demodulation of Forward Fundamental Channel in Additive White Gaussian Noise 4

This test shall be performed on the Forward Fundamental Channel, if the Forward 5

Fundamental Channel is supported by the mobile station. Otherwise, this test shall be 6

performed on the Forward Dedicated Control Channel. This test shall also be performed on 7

the Forward Supplemental Channel and the Forward Supplemental Code Channel if they 8

are supported. Forward Traffic Channel closed loop power control in the base station shall 9

be disabled during this test. 10


The performance of the demodulation of Forward Traffic Channel in an AWGN (no fading or 12

multipath) environment is determined by the frame error rate (FER). The FER is calculated 13

for each individual data rate. For Radio Configuration 2 Fundamental Channel, the 14

accuracy of the Erasure Indicator bits sent by the mobile station is verified in this test. 15






3. For each radio configuration supported on the Forward Fundamental Channel or 21

Forward Dedicated Control Channel, perform steps 4 through 7. 22

4. Set up a call using Fundamental Channel or Dedicated Control Channel test mode 23

(see 1.3) with frame activity equal to 100%. 24


A.2.1.1-18. 26

6. Count, at the base station, the number of frames transmitted and the number of 27

good frames received at the mobile station. 28

7. For Radio Configuration 2, check the accuracy of the received Erasure Indicator 29

bits at the base station against the corresponding frames received at the mobile 30

station. 31

8. For each radio configuration supported on the Forward Supplemental Code 32

Channel or Forward Supplemental Channel, perform steps 9 through 11. 33

9. Set up a call using the appropriate Supplemental Code Channel Test Mode (see 34

1.3) or Supplemental Channel Test Mode (see 1.3) with frame activity equal to 35

100%. 36

3GPP2 C.S0011-C v2.0

3-55


A.2.1.1-34. If the mobile station supports turbo coding on the Forward 2

Supplemental Channel, perform all the turbo coding tests for the supported 3

Forward Supplemental Channel data rates and only the convolutional coding test 4

for the maximum supported Forward Supplemental Channel data rate. If the 5

mobile station only supports convolutional coding on the Forward Supplemental 6

Channel, perform all the convolutional coding tests for the supported Forward 7

Supplemental Channel data rates. 8


good frames received at the mobile station on the Forward Supplemental Code 10

Channel or Forward Supplemental Channel. 11


The actual power measurement uncertainty shall be less than or equal to 0.2 dB. Test 13


The actual Eb/Nt used in each test shall be within ±0.2 dB of the value indicated in Tables 15

A.2.1.1-1 through A.2.1.1-34. 16

For Radio Configuration 2 Fundamental Channels, the mobile station shall set the Erasure 17

Indicator Bit to ‘1’ in the second transmitted frame following the reception of any bad frame 18

on the Forward Fundamental Channel (see Section 2.2.2.2 of [4]). The value of the Erasure 19

Indicator bits corresponding to all other frames received at the mobile station shall be ‘0’. 20



3.4.2 Demodulation of Forward Fundamental Channel in Multipath Fading Channel 23

This test shall be performed on the Forward Fundamental Channel with Radio 24

Configuration 1 or 2, if the Forward Fundamental Channel with Radio Configuration 1 or 2 25

is supported by the mobile station. 26


The performance of the demodulation of Forward Traffic Channel in multipath fading 28

channel is determined by the frame error rate (FER) or the error rate in each frame 29

category. The FER is calculated for each individual data rate. The following table 30

summarizes the fading tests to be performed: 31

32

3GPP2 C.S0011-C v2.0

3-56

Case

Radio Configuration

Channel Simulator Configuration Number

1 1 1 (8 km/h, 2 paths)

2 1 3 (30 km/h, 1 path)

3 1 4 (100 km/h, 3 paths)

4 2 1 (8 km/h, 2 paths)

5 2 3 (30 km/h, 1 path)

6 2 4 (100 km/h, 3 paths)

1

Cases 1 and 4 test the demodulation performance for the 8 km/h, two-path case by 2

checking the full rate FER. Cases 2 and 5 test the demodulation performance for the 30 3

km/h, single-path case by checking the FER at all four possible data rates. Cases 3 and 6 4

test the demodulation performance and the rate determination for the 100 km/h, three-5

path case by checking the FER and the error rate in each frame category. 6






3. If the mobile station supports demodulation of Radio Configurations 1 or 2, set up 12

a call using Fundamental Channel Test Mode 1 or 2 (see 1.3). 13


A.2.2.1-9. 15


good frames received at the mobile station. For Cases 3 and 6, count, at the base 17

station, the number of frames received in each category at the mobile station. 18

3GPP2 C.S0011-C v2.0

3-57





A minimum confidence level of 95% shall be obtained for the following FER requirements 5

(see 6.6). 6

Case 1: 7


A.2.2.1-1 and A.2.2.1-2. 9

The FER for each test at 9600 bps shall not exceed the piece-wise linear FER curve 10

specified by the points in Tables A.2.2.2-1 through A.2.2.2-3. 11

Case 2: 12


A.2.2.1-3 and A.2.2.1-4. 14

The FER for each test shall not exceed the piece-wise linear FER curve specified by the 15

points in Table A.2.2.2-4. 16

Case 3: 17

The actual Eb/Nt used shall be within ±0.2 dB of the value indicated in Table A.2.2.1-5. 18

The FER for each data rate shall not exceed the line specified by the points in Tables 19

A.2.2.2-5 and A.2.2.2-6. The error rate of each frame category should not exceed the 20

corresponding error rate value specified in Tables A.2.2.2-7 and A.2.2.2-8. 21

Case 4: 22

The actual Eb/Nt used in each test shall be within ±0.5 dB of the value indicated in Table 23

A.2.2.1-6. 24

The FER for each test at 14400 bps shall not exceed the piece-wise linear FER curve 25

specified by the points in Table A.2.2.2-9. 26

Case 5: 27

The actual Eb/Nt used in each Band Class 0 test shall be within ±0.5 dB of the value 28

indicated in Tables A.2.2.1-7 and A.2.2.1-8. 29


points in Table A.2.2.2-10. 31

Case 6: 32


A.2.2.1-9. 34

The FER for each data rate shall not exceed the line specified by the points in Table 35

A.2.2.2-11. The error rate of each frame category should not exceed the corresponding 36

error rate value specified in Tables A.2.2.2-12 and A.2.2.2-13. 37

3GPP2 C.S0011-C v2.0

3-58

3.4.3 Demodulation of Forward Fundamental Channel During Soft Handoff 1

This test shall be performed on the Forward Fundamental Channel with Radio 2

Configuration 1, if the Forward Fundamental Channel with Radio Configuration 1 is 3



The performance of the demodulation of Forward Traffic Channel during a two-way soft 6

handoff is determined by the frame error rate (FER). 7



connector as shown in Figure 6.5.1-2, with both channel simulators set to 10

configuration 2 (see Table 6.4.1.3-1). The Forward Channel from base station 1 has 11

an arbitrary pilot PN offset index P1, and is called Channel 1. The Forward 12


Channel 2. 14



3. If the mobile station supports demodulation of Radio Configurations 1, set up a 17

call using Fundamental Channel Test Mode 1 (see 1.3) with 9600 bps data rate 18

only and perform steps 4 through 6. 19

4. Set the test parameters for each test as specified in Table A.2.3.1-1 for both base 20

stations. 21



24


PILOT_PN P1

PILOT_PN P2

25








A.2.3.1-1. 33

3GPP2 C.S0011-C v2.0

3-59


points in Table A.2.3.2-1 with 95% confidence (see 6.6). 2

3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power Control 3

Sets During Soft Handoff 4


When simultaneously receiving channels belonging to different power control sets, the 6

mobile station shall increase its transmit power if all valid power control bits received from 7

all power control sets indicate an increment and shall reduce its transmit power if any valid 8

power control bit received indicates a decrement. This test verifies the above “or of downs” 9

logic. 10



Figure 6.5.1-3. The AWGN generator is not applicable in this test. The Forward 13


Channel 1. The Forward Channel from base station 2 has an arbitrary pilot PN 15

offset index P2, and is called Channel 2. 16










call using Fundamental Channel Test Mode 3 or Dedicated Control Channel Test 26

Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 9 through 14. 27

6. If the mobile station supports demodulation of Radio Configuration 5, set up a call 28

using Fundamental Channel Test Mode 5 or Dedicated Control Channel Test Mode 29

5 (see 1.3) with 14400 bps data rate only and perform steps 9 through 14. 30







9. Set the test parameters as specified in Table A.2.4.1-1 for both base stations. 37

Ensure that both Reverse Pilot Channel gating and Reverse Fundamental Channel 38

gating modes of operation are disabled during the test. 39

3GPP2 C.S0011-C v2.0

3-60



3


USE_TIME 0 (no action time)

PILOT_PN P1

PWR_COMB_IND 0

PILOT_PN P2

PWR_COMB_IND 0 (no combining with P1)

FPC_SUBCHAN_GAIN 0 (0 dB offset)

4

11. After waiting a minimum of 160 ms, synchronously send a periodic pattern of 5

twenty ‘0’ power control bits followed by twenty ‘1’ power control bits on both 6

Channel 1 and Channel 2. 7

12. Measure the output power at the mobile station antenna connector for a duration 8

of 80 power control groups (100 ms). 9

13. Send a periodic pattern of twenty ‘0’ power control bits followed by twenty ‘1’ power 10

control bits on Channel 1. Send continuously ‘0’ power control bits on Channel 2. 11

14. Measure the output power at the mobile station antenna connector for a duration 12

of 80 power control groups (100 ms). 13


The mobile station output power, measured at the mobile station antenna connector, shall 15

have a periodic pattern. In each period the power shall increase monotonically for a 16

duration of 20 power control groups (25 ms) and then decrease monotonically for a 17

duration of 20 power control groups. 18

3.4.5 Decision of Power Control Bit for Channels Belonging to the Same Power Control Set 19


In each power control group containing valid power control bits, the mobile station should 21

provide diversity combining of identical power control subchannels and shall obtain at 22

most one power control bit from each set of identical power control subchannels. This test 23

partially verifies the diversity combining of power control bits belonging to identical power 24

control subchannels and the diversity combining of power control bits belonging to 25

different paths of the same power control subchannel. 26



Figure 6.5.1-3. The AWGN generators and channel simulator for Channel 2 are not 29

3GPP2 C.S0011-C v2.0

3-61

applicable in this test. The Forward Channel from base station 1 has an arbitrary 1

pilot PN offset index P1, and is called Channel 1. The Forward Channel from base 2

station 2 has an arbitrary pilot PN offset index P2, and is called Channel 2.9 3




call using Fundamental Channel Test Mode 1 (see 1.3) and perform steps 9 7

through 12. 8


call using Fundamental Channel Test Mode 2 (see 1.3) and perform steps 9 10

through 12. 11













9. Set the test parameters as specified in Table A.2.5.1-1 for both base stations. 24

Ensure that both Reverse Pilot Channel gating and Reverse Fundamental Channel 25

gating modes of operation are disabled during the test. 26



29

9 Channel 2 may be connected through a channel simulator configured to generate one ray with no fading and no delay in order to time match the no delay setting for Channel 1.

3GPP2 C.S0011-C v2.0

3-62



PILOT_PN P1

PWR_COMB_IND 0

PILOT_PN P2

PWR_COMB_IND 1 (combine with P1)


1

11. After waiting a minimum of 160 ms, begin sending a periodic pattern of one ‘0’ 2

power control bit followed by one ‘1’ power control bit on Channel 1 and a 3

sequence of ‘1’ power control bits on Channel 2. 4

12. Measure the output power at the mobile station antenna connector for at least 40 5

power control groups (50 ms) for each trial. Perform at least 11 trials. 6


In 90% of the trials (each with at least 40 power control groups), the mobile station output 8

power, measured at the mobile station antenna connector, shall follow the power control 9

bit pattern of alternating ‘0’ and ‘1’ sent on Channel 1, with the exception of at most one bit 10

per trial. 11

3.4.6 Demodulation of Power Control Subchannel During Soft Handoff 12


The mobile station shall not use a power control subchannel when the pilot Ec/I0 of the 14

corresponding CDMA Channel is low. This test verifies that the mobile station stops using a 15

power control subchannel in the “or of downs” when the pilot Ec/I0 of the corresponding 16

CDMA Channel is low. 17





Channel 1. The Forward Channel from base station 2 has an arbitrary pilot PN 22

offset index P2, and is called Channel 2. 23






3GPP2 C.S0011-C v2.0

3-63


call using Fundamental Channel Test Mode 2 (see 1.3) ) with 14400 bps data rate 2














9. Set the test parameters as specified in Table A.2.6.1-1 and Figure 3.4.6.2-1 for 16

both base stations. Ensure that both Reverse Pilot Channel gating and Reverse 17

Fundamental Channel gating modes of operation are disabled during the test. 18



21



PILOT_PN P1

PWR_COMB_IND 0

PILOT_PN P2

PWR_COMB_IND 0 (no combining with P1)


22

11. After waiting a minimum of 160 ms, synchronously send a periodic pattern of one 23

‘0’ power control bit followed by one ‘1’ power control bit on both Channel 1 and 24

Channel 2. 25

12. Measure the mobile station output power at the mobile station antenna connector 26

for at least 22 seconds, which does not have to be contiguous. The 22-second 27

period must contain at least 11 transitions from the state where Channel 2 Pilot 28

Ec/I0 changes from -10 dB to -20 dB. 29

30

3GPP2 C.S0011-C v2.0

3-64

10 dB

Channel 1 Pilot

Channel 2 Pilot

Pilot Ec/Io = -10 dB

1 1 1 1 Time (s) 1

Figure 3.4.6.2-1. Demodulation of Power Control Subchannel During Soft Handoff 2



be in a steady state, defined as steady state 1, when the pilot Ec/I0 value of Channel 2 is 5

-10 dB, and it shall follow the power control bit pattern of alternating ‘0’ and ‘1’ in 85% of 6

the 1-second steady state 1 segments with 90% confidence. The mobile station output 7

power shall be in a steady state, defined as steady state 2, no later than 40 ms after the 8

pilot Ec/I0 value of Channel 2 drops to -20 dB in 90% of the trials, and shall follow the 9

power control bit pattern of alternating ‘0’ and ‘1’. The mobile station output power in 10

steady state 2 shall be no greater than the mobile station output power in steady state 1, 11

and shall be greater than the mobile station output power in steady state 1 minus 12 dB. 12

3.4.7 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Closed 13

Loop Power Control (FPC_MODE = ‘000’) 14



performed on the Forward Dedicated Control Channel. Forward Traffic Channel closed loop 17

power control in the base station shall be enabled during this test. 18


When FPC_MODE equals ‘000’, the mobile station uses the 800 bps Primary Reverse Power 20

Control Subchannel to support Forward Traffic Channel power control. 21

The performance of forward power control is measured by the mobile station received FER 22

while not exceeding the specified Traffic Eb/Nt limits. The FER is calculated for each 23

individual data rate. The FER is calculated for active frames only. 24




3GPP2 C.S0011-C v2.0

3-65





Mode 3 with 100% frame activity (see 1.3) and perform steps 7 through 11. 5



5 with 100% frame activity (see 1.3) and perform steps 7 through 11. 8


up a call using Fundamental Channel Test Mode 7 or Dedicated Control Channel 10

Test Mode 7 with 100% frame activity (see 1.3) and perform steps 7 through 11. 11




7. Set the parameters of each test as specified in Tables A.2.7.1-1 through A.2.7.1-9. 15

Note that the values of signaling parameters FPC_FCH_INIT_SETPT or 16

FPC_DCCH_INIT_SETPT are not directly specified. Tests that are not supported by 17

the mobile station may be omitted. 18

8. When performing the test on the Fundamental Channel, transmit random data to 19

the mobile station on the Forward Fundamental Channel at a fixed data rate. 20

When performing the test on the Dedicated Control Channel, transmit random data 21

to the mobile station on the Forward Dedicated Control Channel at one fixed data 22

rate. 23

9. Activate the Forward Traffic Channel power control and command the base station 24

to respond to the power control bits received on the Reverse Power Control 25

Subchannel. Set the base station to limit its output traffic channel power to the 26

maximum Traffic Ec/Ior value specified in Table A.2.7.1-1. 27

10. Adjust the mobile station transmission power so that no bit errors on the Reverse 28

Power Control Subchannel are expected at the base station receiver. 29

11. Count at the base station the number of Forward Traffic Channel frames 30

transmitted and the number of good Forward Traffic Channel frames received at 31

the mobile station. 32





The actual FCH Eb/Nt or DCCH Eb/Nt used in each test shall be within ±0.5 dB of the 37

value indicated in Tables A.2.7.1-2 through A.2.7.1-9. 38

The FER for each test should not exceed the piecewise linear FER curve specified by the 39


3GPP2 C.S0011-C v2.0

3-66


Loop Power Control (FPC_MODE = ‘010’) 2

This test shall be performed on the Forward Supplemental Channel, if the Forward 3

Supplemental Channel is supported by the mobile station. Forward Traffic Channel closed 4

loop power control in the base station shall be enabled during this test. 5


When FPC_MODE equals ‘010’, the mobile station uses the 600 bps Secondary Reverse 7

Power Control Subchannel to support Forward Supplemental Channel power control. 8

The performance of forward power control is measured by the mobile station received FER 9

while not exceeding the specified Supplemental Eb/Nt limits. The FER is calculated for the 10

lowest fixed data rate and highest fixed data rate supported by the mobile station. The FER 11

is calculated for active frames only. 12







call using Supplemental Channel Test Mode 3 with 100% frame activity (see 1.3) 19

and perform steps 7 through 12. 20


using Supplemental Channel Test Mode 5 with 100% frame activity (see 1.3) and 22

perform steps 7 through 12. 23


up a call using Supplemental Channel Test Mode 7 with 100% frame activity (see 25

1.3) and perform steps 7 through 12. 26




7. Transmit random data to the mobile station on the Forward Supplemental Channel 30

at the lowest fixed data rate, as specified in Tables A.2.8.1-2 through A.2.8.1-5, 31



Note that the value of signaling parameter FPC_SCH_INIT_SETPT is not directly 34

specified. Tests that are not supported by the mobile station may be omitted. 35




maximum Supplemental Ec/Ior value shown in Table A.2.8.1-1. 39

3GPP2 C.S0011-C v2.0

3-67



11. Count at the base station the number of Forward Supplemental Channel frames 3

transmitted and the number of good Forward Supplemental Channel frames 4

received at the mobile station. 5


at the highest fixed data rate supported by the mobile station and repeat steps 8 7

through 11. 8





The actual Supplemental Eb/Nt used in each test shall be within ±0.5 dB of the value 13

indicated in Tables A.2.8.1-2 through A.2.8.1-5. 14

The FER for each test should not exceed the piecewise linear FER curve specified by the 15


3.4.9 Demodulation of Forward Traffic Channel in Multipath Fading Channel with Outer 17

Loop Power Control and Closed Loop Power Control (FPC_MODE = ‘000’, ‘001’ and 18

‘010’) 19



performed on the Forward Dedicated Control Channel. Forward Traffic Channel closed loop 22

power control in the base station shall be enabled during this test. 23


When operating with radio configurations greater than or equal to 3, the mobile station 25

supports both inner power control loop and outer power control loop for Forward Traffic 26

Channel power control. To maintain the Frame Error Rate (FER) of the Forward Traffic 27

Channel, the mobile station inner power control loop measures the Eb/Nt of the received 28

Forward Traffic Channel, and compares it with the corresponding outer power control loop 29

setpoint. The power control bits are transmitted to the base station on the Reverse Power 30

Control Subchannel. 31

The performance of the forward power control is measured by the difference between the 32

mobile station received FER and the assigned target FER while also checking the average 33

Traffic Eb/Nt at the base station under a given channel simulator configuration. 34




3GPP2 C.S0011-C v2.0

3-68
















Tests that are not supported by the mobile station may be omitted. 16





rate. 21




maximum Traffic Ec/Ior value specified in Table A.2.9.1-1. 25










For Tests 1-3, 5-7, 9-11, 13-15, 17-19, 21-23, 25-27, and 29-31, the mobile station 35

received FER on the Forward Fundamental Channel or the Forward Dedicated Control 36

Channel shall be within the range 1% ±0.5% with 90% confidence (see 6.6). 37

For Tests 4, 8, 12, 16, 20, 24, 28 and 32, the mobile station received FER on the Forward 38

Fundamental Channel or the Forward Dedicated Control Channel shall be within the range 39

10% ±1% with 90% confidence (see 6.6). 40

3GPP2 C.S0011-C v2.0

3-69

The required Traffic Eb/Nt to achieve the specified FER shall not exceed the values 1

specified in Tables A.2.9.2-1 through A.2.9.2-4. 2


Loop Power Control (FPC_MODE = ‘000’) and Transmit Diversity (OTD or STS) 4

Forward Traffic Channel closed loop power control in the base station shall be enabled 5

during this test. 6


The performance of the demodulation of Forward Traffic Channel with closed loop power 8

control and transmit diversity is tested. 9


1. Connect the base station, channel simulators and AWGN noise generator to the 11

mobile station antenna connector as shown in Figure 6.5.1-5. 12






4. If the mobile station supports demodulation of Radio Configuration 3 or 4, and the 18

Forward Dedicated Control Channel, set up a call using Dedicated Control Channel 19





6. If the mobile station supports demodulation of Radio Configuration 5 and the 24

Forward Dedicated Control Channel, set up a call using Dedicated Control Channel 25


7. Set the following parameters in the Sync Channel Message: 27

28




29


A.2.10.1-9. Tests that are not supported by the mobile station may be omitted. 31



3GPP2 C.S0011-C v2.0

3-70



rate. Control the enabling and disabling of frame transmission according to the 3

frame activity. 4




maximum Traffic Ec/Ior values shown in Table A.2.10.1-1. 8












The actual FCH Eb/Nt or DCCH Eb/Nt used in each test shall be within ±0.5 dB of the 20

value indicated in Tables A.2.10.1-2 through A.2.10.1-9. 21




Loop Power Control (FPC_MODE = ‘010’) and Transmit Diversity (OTD or STS) 25

Forward Traffic Channel closed loop power control in the base station shall be enabled 26

during this test. 27


The performance of the demodulation of Forward Supplemental Channel with closed loop 29

power control and transmit diversity is tested. 30


1. Connect the base station, channel simulators and AWGN noise generator to the 32

mobile station antenna connector as shown in Figure 6.5.1-5. 33



3GPP2 C.S0011-C v2.0

3-71


up a call using Supplemental Channel Test Mode 3 with 100% frame activity (see 2

1.3) and perform steps 5 through 11. 3




5. Set the following parameters in the Sync Channel Message: 7

8




9


A.2.11.1-5. Tests that are not supported by the mobile station may be omitted. 11


at one fixed data rate. 13




maximum Supplemental Ec/Ior value shown in Table A.2.11.1-1. 17



10. Count at the base station the number of Forward Supplemental Channel frames 20

transmitted and the number of good Forward Supplemental Channel frames 21

received at the mobile station. 22







The actual SCH Eb/Nt used in each test shall be within ±0.5 dB of the value indicated in 29

Tables A.2.11.1-2 through A.2.11.1-5. 30



3GPP2 C.S0011-C v2.0

3-72

3.4.12 Demodulation of Power Control Subchannel During Reverse Pilot Channel Gating 1

This test shall be performed on the Forward Dedicated Control Channel, if supported by 2



The mobile station shall not use a power control bit that corresponds to a gated off period 5

on the reverse link during Reverse Pilot Channel gating. This test verifies that the mobile 6

station does not use these invalid power control bits. 7


1. Connect the base station to the mobile station antenna connector as shown in 9

Figure 6.5.1-4. 10



3. If the mobile station supports Reverse Radio Configuration 3 or 4, and if the mobile 13

station supports Reverse Pilot Channel gating, set up a call using Dedicated 14

Control Channel Test Mode 3 (see 1.3). Send Non-Negotiable Service Configuration 15

information record messages to the mobile station, so that 16

PILOT_GATING_USE_RATE = ‘1’ and PILOT_GATING_RATE = ‘10’ (1/4 rate). The 17

base station shall not transmit on the Forward Dedicated Control Channel to the 18

mobile station under test during the test. Perform steps 5 through 7. 19





PILOT_GATING_USE_RATE = ‘1’ and PILOT_GATING_RATE = ‘10’ (1/4 rate). The 24

base station shall not transmit on the Forward Dedicated Control Channel to the 25

mobile station under test during the test. Perform steps 5 through 7. 26

5. Set the test parameters as specified in Table A.2.12.1-1. Set the reverse power 27

control delay test parameter, REV_PWR_CNTL_DELAY, to what the base station is 28

using. 29

6. After waiting a minimum of 160 ms, send a periodic pattern of four ‘0’ power 30

control bits followed by four ‘1’ power control bits on the Forward Power Control 31

Subchannel regardless of whether these bits would be considered by the mobile 32

station as valid or not. 33


for at least 5 seconds. 35



follow the valid power control bit pattern in 85% of the trials. 38

3GPP2 C.S0011-C v2.0

3-73

3.4.13 Demodulation of Power Control Subchannel During Reverse Fundamental Channel 1

Gating 2


The mobile station shall not use a power control bit that corresponds to a gated off period 4

on the reverse link during Reverse Fundamental Channel gating. This test verifies that the 5

mobile station does not use these invalid power control bits. 6



Figure 6.5.1-4. 9



3. If the mobile station supports Reverse Radio Configuration 3 or 4, set up a call 12

using Fundamental Channel Test Mode 3 (see 1.3). Send an Extended Channel 13

Assignment Message to the mobile station with REV_FCH_GATING_MODE equal to 14

‘1’ (50% R-FCH transmission duty cycle). The base station shall transmit 15

continuous 20 ms frames at 1500 bps on the Forward Fundamental Channel to 16

the mobile station under test during the test. Perform steps 5 through 7. 17

4. If the mobile station supports Reverse Radio Configuration 5 or 6, set up a call 18

using Fundamental Channel Test Mode 7 (see 1.3). Send an Extended Channel 19

Assignment Message to the mobile station with REV_FCH_GATING_MODE equal to 20

‘1’ (50% R-FCH transmission duty cycle). The base station shall transmit 21

continuous 20 ms frames at 1500 bps on the Forward Fundamental Channel to 22

the mobile station under test during the test. Perform steps 5 through 7. 23

5. Set the test parameters as specified in A.2.13.1-1. Set the reverse power control 24

delay test parameter, REV_PWR_CNTL_DELAY, to what the base station is using. 25

6. After waiting a minimum of 160 ms, send a periodic pattern of one ‘0’ power 26

control bit followed by one ‘1’ power control bit on the Forward Power Control 27

Subchannel, regardless of whether these bits would be considered by the mobile 28

station as valid or not. 29


for at least 5 seconds 31



follow the valid power control bit pattern in at least 85% of the trials. 34

3.4.14 Demodulation of Forward Packet Data Channel in Additive White Gaussian Noise 35

This test shall be performed on the Forward Packet Data Channel, if the Forward Packet 36

Data Channel and Forward Packet Data Control Channel are supported by the mobile 37

station. 38

3GPP2 C.S0011-C v2.0

3-74


The performance of the demodulation of Forward Packet Data Channel in an AWGN (no 2

fading or multipath) environment is determined by the packet error rate (PER). The PER is 3

calculated for each individual data rate. 4




Channel, which will contain the power control subchannel. The forward link closed loop 8

power control shall be disabled in the base station. The base station shall set the 9

transmission format, the number of retransmissions and power level of the Forward Packet 10

Data Channel independent of the data received on the Reverse Channel Quality Indicator 11

Channel and the Reverse Acknowledgment Channel. 12






3. For each radio configuration supported on the Forward Packet Data Channel and 18

Forward Packet Data Control Channel, perform steps 4 through 7. 19

4. Set up a call using Packet Data Channel Test Mode 10a (see 1.3) with 100% packet 20

data channel activity on the maximum number of ARQ Channels supported by the 21

mobile station. Make sure that all subpackets sent on the Forward Packet Data 22

Channel are addressed to the mobile station. 23

5. Configure the base station to set the SPID field to ‘00’ in every message sent on the 24

Forward Packet Data Control Channel. 25


A.2.14.1-22. 27

7. Count, at the base station, the number of packets transmitted, and at the mobile 28

station the number of good packets received on the Forward Packet Data Channel. 29

A good packet is one that passes the CRC check after any of the subpacket 30

transmissions. 31





The actual Forward Packet Data Channel Eb/Nt used in each test shall not exceed the 36

range specified in tables A.2.14.2-1 through A.2.14.2-19 and shall not be more than 0.2 dB 37

from the value specified in the tables A.2.14.1-1 through A.2.14.1-22. Note that when 38

retransmissions occur, the Forward Packet Data Channel Eb/Nt is determined without 39

summing the received F-PDCH energy across individual retransmissions. 40

3GPP2 C.S0011-C v2.0

3-75

The PER for each test shall not exceed the piecewise linear PER curve specified by the 1


3.4.15 Demodulation of Forward Packet Data Channel in Multipath Fading Channel with 3

no Power Control 4

This test shall be performed on the Forward Packet Data Channel if the Forward Packet 5

Data Channel and the Forward Packet Data Control Channel are supported by the mobile 6

station. Forward Traffic Channel closed loop power control in the base station shall be 7

disabled during this test. 8


The performance of the demodulation of Forward Packet Data Channel in multipath fading 10

environments is determined by the packet error rate (PER). The PER is calculated 11

individually for each tested Forward Packet Data Channel configuration. 12




Channel, which will contain the power control subchannel. The Forward Traffic Channel 16

closed loop power control in the base station shall be disabled. The base station shall set 17

the transmission format, the number of retransmissions and power level of the Forward 18

Packet Data Channel independent of the data received on the Reverse Channel Quality 19

Indicator Channel and the Reverse Acknowledgment Channel. 20






3. For each radio configuration supported on the Forward Packet Data Channel and 26

Forward Packet Data Control Channel, perform steps 4 through 7. 27

4. Set up a call using Packet Data Channel Test Mode 10a (see 1.3) with 100% packet 28

data channel activity on the maximum number of ARQ Channels supported by the 29

mobile station. Make sure that all subpackets sent on the Forward Packet Data 30

Channel are addressed to the mobile station. 31


A.2.15.1-6. 33

6. Configure the base station to increment the SPID field included in the Forward 34

Packet Data Control message by one between subsequent retransmissions of the 35

same packet on the Forward Packet Data Channel. 36

7. Count, at the base station, the number of encoder packets transmitted, and at the 37

mobile station the number of good packets received on the Forward Packet Data 38

3GPP2 C.S0011-C v2.0

3-76

Channel. A good packet is one that passes the CRC check after any of the 1

subpacket transmissions. 2





The actual Forward Packet Data Channel Eb/Nt used in each test shall not exceed the 7

range specified in table A.2.15.2-1 through A.2.15.2-3 and shall not be more than 0.5 dB 8

from the value specified in the tables A.2.15.1-1 through A.2.15.1-6. Note that when 9

retransmissions occur, the Forward Packet Data Channel Eb/Nt is determined without 10

summing the received F-PDCH energy across individual retransmissions. 11

The PER for each test shall not exceed the piecewise linear PER curve specified by the 12

points in Table A.2.15.2-1 through A.2.15.2-3 with 95% confidence (see 6.6). 13

3.5 Receiver Performance 14

3.5.1 Receiver Sensitivity and Dynamic Range 15


The RF sensitivity of the mobile station receiver is the minimum received power, measured 17

at the mobile station antenna connector, at which the frame error rate (FER) does not 18

exceed a specified value. The receiver dynamic range is the input power range at the mobile 19

station antenna connector over which the FER does not exceed a specific value. 20



Figure 6.5.1-4. The AWGN generator and the interference generator are not 23

applicable in this test. 24

2. For all tests, Forward Traffic Channel closed loop power control should be disabled 25

in the base station. 26

3. For each band class that the mobile station supports, configure the base station to 27


4. If the mobile station supports demodulation of Radio Configuration 1, 2, 3, 4, or 5, 29

set up a call using Fundamental Channel Test Mode 1 or 3 or Dedicated Control 30

Channel Test Mode 3 (see 1.3) with 9600 bps data rate only, or Fundamental 31

Channel Test Mode 2 or 5, or Dedicated Control Channel Test Mode 5 (see 1.3) with 32

14400 bps data rate only and perform steps 6 through 8. 33


set up a call using Fundamental Channel Test Mode 7 or Dedicated Control 35


through 8. 37

3GPP2 C.S0011-C v2.0

3-77

6. Set the test parameters for Test 1 as specified in Table 3.5.1.2-1 and perform step 1

8. 2


8. 4



7

Table 3.5.1.2-1. Test Parameters for Receiver Sensitivity and Dynamic Range 8

Parameter Units Test 1 Test 2

Îor dBm/1.23 MHz -104 -25

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (RC 1 and 3) -12.3 (RC 2 and 5)

-20.6 (RC 7)

For the case of a Spreading Rate 3 system, Îor is the received power on each carrier.

9


The FER in each test shall not exceed 0.5% with 95% confidence (see 6.6). 11

3.5.2 Single Tone Desensitization 12


Single tone desensitization is a measure of a receiver’s ability to receive a CDMA signal at 14

its assigned channel frequency in the presence of a single tone spaced at a given frequency 15

offset from the center frequency of the assigned channel. The receiver desensitization 16

performance is measured by the frame error rate (FER). 17

This test is applied to all band classes except Band Class 6, where no narrow-band 18

interferers are currently known. 19


1. Connect the base station and an interfering CW tone to the mobile station antenna 21




3GPP2 C.S0011-C v2.0

3-78

3. For each band class that the mobile station supports, except Band Class 6, 1

configure the base station to operate in that band class and perform steps 4 2

through 11. 3




through 11. 7




through 11. 11

6. Set the test parameters for Test 1 as specified in Table 3.5.2.2-1 and perform steps 12

10 and 11. 13


10 and 11. 15

8. If the mobile station is operating in Band Class 1, 3, 4, 8, 14 or 15 with Radio 16

Configuration 3 or 7, set the test parameters for Test 3 and perform steps 10 and 17

11. 18

9. If the mobile station is operating in Band Class 1, 3, 4, 8, 14 or 15 with Radio 19

Configuration 3 or 7, set the test parameters for Test 4 and perform steps 10 and 20

11. 21

10. If the mobile station is operating in Band Class 1, 3, 4, 8, 14 or 15 use closed loop 22

power control commands to adjust the mobile station transmit power, as measured 23

at the mobile station antenna connector. For Band Class 1, 4, and 8, using the 24

antenna gain recommended by the mobile station manufacturer, set the EIRP to a 25

level higher than the minimum specified in Table 3.5.2.2-2 for the current test. For 26

Band Class 3, set the ERP to a level higher than the minimum specified in Table 27

3.5.2.2-3 for the current test. 28



31

Deleted: or

Deleted: or

Deleted: or

3GPP2 C.S0011-C v2.0

3-79

Table 3.5.2.2-1. Test Parameters for Single Tone Desensitization 1

Parameter Units Tests 1 and 3 Tests 2 and 4

Tone Offset from Carrier

SR 1 kHz +900 (Band Groups 450 and 800)

+1250 (BC 1, 4, 8, 14 and 15)

-900 (Band Groups 450 and 800)

–1250 (BC 1, 4, 8, 14 and 15)

SR 3 kHz +250010 -2500

Tone Power dBm -30 (Tests 1 and 2) -40 (Tests 3 and 4)

Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)


2

Table 3.5.2.2-2. Minimum Effective Isotropic Radiated Power for Single Tone 3

Desensitization Test for Band Classes 1, 4, and 8 4

Minimum Mobile Station EIRP Mobile Station Class Tests 1 and 2 Tests 3 and 4

I -10 dBW (100 mW) -5 dBW (320 mW)

II -15 dBW (32 mW) -10 dBW (100 mW)

III -18 dBW (16 mW) -15 dBW (32 mW)

IV -21 dBW (8 mW) -20 dBW (10 mW)

V -24 dBW (4 mW) -25 dBW (3.2 mW)

5

10 When a Spreading Rate 3 system is overlaid on either of the Primary CDMA Channels for Band Class 0, the position of the closest interferer (AMPS paging channel) is 2.13 MHz away from the center of the Spreading Rate 3 signal. To minimize the potential for interference, a base station operating in a Spreading Rate 3 mode should not overlay the Primary CDMA Channel when operating in Band Class 0 unless the CDMA base station is co-located with the AMPS base station.

Deleted: BC 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: BC 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: and

Deleted: and

3GPP2 C.S0011-C v2.0

3-80

Table 3.5.2.2-3. Minimum Effective Radiated Power for Single Tone Desensitization 1

Test for Band Class 3 2

Minimum Mobile Station ERP Mobile Station Class Tests 1 and 2 Tests 3 and 4

I -7 dBW (200 mW) -2 dBW (630 mW)

II -11 dBW (80 mW) -6 dBW (250 mW)

III -15 dBW (32 mW) -10 dBW (100 mW)

3



3.5.3 Intermodulation Spurious Response Attenuation 6


The intermodulation spurious response attenuation is a measure of a receiver's ability to 8

receive a CDMA signal on its assigned channel frequency in the presence of two interfering 9

CW tones. These tones are separated from the assigned channel frequency and are 10

separated from each other such that the third order mixing of the two interfering CW tones 11

can occur in the non-linear elements of the receiver, producing an interfering signal in the 12

band of the desired CDMA signal. The receiver performance is measured by the frame error 13

rate (FER). 14


1. Connect the base station and two interfering CW tones to the mobile station 16

antenna connector as shown in Figure 6.5.1-4. 17



3. For each band class that the mobile station supports, configure the base station to 20





through 12. 25




through 12. 29

6. Set the test parameters for Test 1 as specified in Table 3.5.3.2-1, 3.5.3.2-2, or 30

3.5.3.2-3 and perform step 12. 31

3GPP2 C.S0011-C v2.0

3-81

7. Set the test parameters for Test 2 as specified in Table 3.5.3.2-1, 3.5.3.2-2, or 1

3.5.3.2-3 and perform step 12. 2

8. If the mobile station is operating in Band Class 0, set the test parameters for Test 3 3

as specified in Table 3.5.3.2-4 and perform step 12. 4









13

Table 3.5.3.2-1. Test Parameters for Band Groups 450 and 800 Intermodulation 14

Spurious Response Attenuation (Tests 1 and 2) 15

Mobile Station Class I

Mobile Station Class II and III

Parameter Units Test 1 Test 2 Test 1 Test 2

SR 1 kHz +900 -900 +900 -900 Tone 1 Offset from Carrier SR 3 MHz +2.50 -2.50 +2.50 -2.50

Tone Power 1 dBm -40 -43

SR 1 kHz +1700 -1700 +1700 -1700 Tone 2 Offset from Carrier SR 3 MHz +3.30 -3.30 +3.30 -3.30


Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)


When operating a Spreading Rate 3 system that is overlaid on a Spreading Rate 1carrier, the Spreading Rate 1 intermodulation tests shall not apply.

16

Deleted: Band Classes 0, 2, 3, 5, 7, 9, 10, 11 and 12

3GPP2 C.S0011-C v2.0

3-82

Table 3.5.3.2-2. Test Parameters for Band Class 1, 4, 8, 14 and 15 Intermodulation 1

Spurious Response Attenuation (Tests 1 and 2) 2


Mobile Station Class II through Class

V


SR 1 MHz +1.25 -1.25 +1.25 -1.25 Tone 1 Offset from Carrier SR 3 MHz +2.50 -2.50 +2.50 -2.50




Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)



3

Deleted: and

3GPP2 C.S0011-C v2.0

3-83

Table 3.5.3.2-3. Test Parameters for Band Class 6 Intermodulation Spurious Response 1

Attenuation (Tests 1 and 2) 2


Mobile Station Class II through Class

V


SR 1 MHz +2.5 -2.5 +2.5 -2.5 Tone 1 Offset from Carrier SR 3 MHz +5 -5 +5 -5

SR 1 dBm -48 -48 Tone 1 Power

SR 3 dBm -46 -46


SR 1 dBm -48 -48 Tone 2 Power

SR 3 dBm -46 -46

Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)



3

3GPP2 C.S0011-C v2.0

3-84




Tone 1 Offset from Carrier kHz +900 -900

Tone Power 1 dBm -32



Îor dBm/1.23 MHz -90

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6

3









orc

IEPilot dB -7

orc

IE Traffic

dB -15.6

6


The FER in Tests 1, 2, 5, and 6 shall not exceed 1.0% with 95% confidence (see 6.6). 8

The FER in Tests 3 and 4 should not exceed 1.0% with 95% confidence (see 6.6). 9

3.5.4 Adjacent Channel Selectivity 10

This test is applicable to Band Class 6 mobile stations only. 11

3GPP2 C.S0011-C v2.0

3-85


Adjacent channel selectivity is a measure of the ability to receive a CDMA signal on the 2

assigned channel frequency in the presence of another CDMA signal that is offset from the 3

center frequency of the assigned channel by ± 2.5 MHz for Spreading Rate 1 or ± 5 MHz for 4

Spreading Rate 3. 5


1. Connect the base station and an interfering modulated signal to the mobile station 7

antenna connector as shown in Figure 6.5.1-4. The modulated interference shall be 8

a signal modulated with a combination of Pilot, Sync, Paging and Traffic Channels 9

as specified in Table 3.5.4.2-1. The source shall be Radio Configuration 3 with full 10

rate traffic channels for Spreading Rate 1 tests, and Radio Configuration 6 with full 11

rate traffic channels for Spreading Rate 3 tests. 12



3. Configure the base station to operate in Band Class 6 and perform steps 4 through 15

9. 16





up a call using Fundamental Channel Test Mode 1 or 3 or Dedicated Control 21


through 9. 23




and 8. 27


9. 29


9. 31



34

3GPP2 C.S0011-C v2.0

3-86

Table 3.5.4.2-1. Configuration for Interference Source 1

Channel Type

Number of Channels

Fraction of Power (linear)

Fraction of Power (dB)

Comments

Forward Pilot 1 0.2000 -7.0 Code channel 1280W

Sync 1 0.0471 -13.3 Code channel 6432W ;

always 1/8 rate

Paging 1 0.1882 -7.3 Code channel 641W ;

full rate only

Traffic 6 0.09412 -10.3 Variable code channel assignments; full rate

only

2

Table 3.5.4.2-2. Test Parameters for Adjacent Channel Selectivity 3

Parameter Units Tests 1 Tests 2

SR 1 MHz +2.5 -2.5 Adjacent CDMA

Channel Offset from Carrier

SR 3 MHz +5.0 -5.0

dBm/1.23 MHz

-37 (SR 1)

Interference Source, modulated source

dBm / 3.69 MHz

-46 (SR 3)

dBm/ 1.23 MHz

-101 (SR1) Îor

dBm/ 3.69 MHz

-96 (SR3)

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)


4



3GPP2 C.S0011-C v2.0

3-87

3.5.5 Receiver Blocking Characteristics 1

This test is applicable to Band Class 6 mobile stations only. 2


The receiver blocking characteristic is a measure of the receiver’s ability to receive a CDMA 4

signal at its assigned channel frequency in the presence of a single tone on frequencies 5

other than those of the adjacent channels, without this unwanted input signal causing a 6

degradation of the performance of the receiver beyond a specified limit. 7


1. Connect the base station and an interfering CW tone to the mobile station antenna 9


2. For all tests, Forward Power Control should be disabled in the base station. 11

3. Configure the base station to operate in Band Class 6. 12





up a call using Fundamental Test Mode 1 or 3 or Dedicated Control Channel Test 17



set up a call using Fundamental Test Mode 7 or Dedicated Control Channel Test 20



15. 23


15. 25


15. 27


15. 29


14 and 15 using the Default CW Tone Power. 31





14. Step the CW tone frequency through each inclusive range of frequencies given for 36

the current test in Table 3.5.5.2-2 at 1 MHz intervals and perform step 15. 37

3GPP2 C.S0011-C v2.0

3-88



16. If spurious responses occurred in tests 6 or 7 repeat step 15 for each spurious 3

response frequency using the Alternate CW Tone Power given in Table 3.5.5.2-2. 4

5

Table 3.5.5.2-1. Test Parameters for Receiver Blocking Characteristics (In-Band) 6

Parameter Units Test 1 Tests 2 Tests 3 Tests 4

CW Tone Offset SR 1 kHz +5000 -5000 +7500 -7500

from Carrier SR 3 kHz +10000 -10000 +15000 -15000

CW Tone Power dBm -56 -44

Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)


7

Table 3.5.5.2-2. Test Parameters for Receiver Blocking Characteristics (Out-Of-Band) 8


CW Tone Frequency

MHz 2051 – 2095

2185 – 2230

2026 – 2050

2231 – 2255

1 – 2025

2255 – 12750

Default

CW Tone Power dBm -44 -30 -15

Alternate

CW Tone Power dBm – -44 -44

Îor dBm/ 1.23 MHz

-101

orc

IEPilot dB -7

orc

IE Traffic

dB -15.6 (SR 1) -20.6 (SR 3)


9

Deleted: s

3GPP2 C.S0011-C v2.0

3-89


The following requirements apply independently for each supported test mode. The FER in 2

tests 1 through 5 shall not exceed 10% with 90% confidence (see 6.6). With up to a 3

combined total between tests 6 and 7 of twenty-four (24) exceptions at spurious response 4

frequencies in each assigned frequency channel, the FER in tests 6 and 7 shall not exceed 5

10% with 90% confidence (see 6.6). For each spurious response exception, the FER shall 6

not exceed 10% with 90% confidence (see 6.6) when using the Alternate CW Tone Power for 7

interference at the one or more spurious response frequencies. 8

3.6 Limitations on Emissions 9

3.6.1 Conducted Spurious Emissions 10


Conducted spurious emissions are spurious emissions generated or amplified in a receiver 12

that appear at the mobile station antenna connector. 13


1. Connect a spectrum analyzer (or other suitable test equipment) to the mobile 15

station antenna connector. 16


to operate in that band class and perform steps 3 and 4. 18

3. Enable the mobile station receiver for CDMA-only mode, so that the mobile station 19

continuously cycles between the System Determination Substate and the Pilot 20

Channel Acquisition Substate of the Mobile Station Initialization State. Since there is 21

no Forward CDMA Channel for this configuration, the mobile station should not 22

pass the Pilot Channel Acquisition Substate. 23

4. For all band classes measure the spurious emission levels. For all band classes, 24

except Band Class 6, begin the spectrum analyzer sweep from the lowest 25

intermediate frequency, the lowest oscillator frequency used in the receiver, or 1 26

MHz, whichever is lowest. For Band Classes 0, 2, 5, 7, 9, 10, 11, and 12 sweep to 27

at least 2600 MHz. For Band Class 3 sweep to at least 3 GHz. or For Band Classes 28

1, 4, 8, 14, and 15 sweep to at least 6 GHz. For Band Class 6, sweep the spectrum 29

analyzer over a frequency range from 30 MHz to at least 12.75 GHz. 30


The mean conducted spurious emissions with ten or more averages for a mobile station 32

shall be: 33

1. Less than -76 dBm for all band classes except Band Class 3, or –81 dBm for Band 34

Class 3, measured in a 1 MHz resolution bandwidth at the mobile station antenna 35

connector, for frequencies within the mobile station receive band (see 3.1) 36

associated with each band class that the mobile station supports. 37

Formatted: Font: Bookman OldStyle



Deleted: 0, 1, 2, 3, 4, 5, 7, 8, 9, 10, 11 and 12,

Deleted: sweep

Deleted: over a frequency range

Deleted: or

Deleted: ,

Deleted: for band classes 0, 2, 5, 7, 9, 10, 11 and 12, 3 GHz for

Deleted: or

Deleted: for band classes 1, 4 and 8, and measure the spurious emission levels

Deleted: and measure the spurious emissions levels

Deleted: band classes 0, 1, 2, 4, 5, 6, 7, 8, 9, 10, 11 and 12

3GPP2 C.S0011-C v2.0

3-90

2. Less than -61 dBm, measured in a 1 MHz resolution bandwidth at the mobile 1

station antenna connector, for frequencies within the mobile station transmit band 2

(see 3.1) associated with each band class that the mobile station supports. 3

3. Less than –57 dBm for Band Class 6, measured in a 100 kHz resolution bandwidth 4

at the mobile station antenna connector (see 3.1), for frequencies from 30 MHz to 1 5

GHz. 6

4. Less than -47 dBm for all band classes except Band Class 3 and 6, or –54 dBm for 7

Band Class 3, measured in a 30 kHz resolution bandwidth at the mobile station 8

antenna connector (see 3.1), for all other frequencies. Less than –47 dBm for Band 9

Class 6, measured in a 1 MHz resolution bandwidth at the mobile station antenna 10

connector (see 3.1), for all other frequencies in the range from 1 GHz to 12.75 GHz. 11

Current region-specific radio regulation rules shall also apply. 12

For example, a Band Class 6 mobile station operating under Japan regional 13

requirements shall limit conducted emissions less than -41 dBm, measured in a 14

300 kHz resolution bandwidth at the mobile station antenna connector, for 15

frequencies within the PHS band from 1884.5 to 1919.6 MHz. 16

3.6.2 Radiated Spurious Emissions 17


Radiated spurious emissions are those spurious emissions generated or amplified in a 19

receiver and radiated by the antenna, housing and all power, control, and audio leads 20

connected to the receiver. 21




2. Enable the mobile station receiver for CDMA-only mode, so that the mobile station 25

continuously cycles between the System Determination Substate and the Pilot 26

Channel Acquisition Substate of the Mobile Station Initialization State. Since there is 27

no Forward CDMA Channel, the mobile station should not pass the Pilot Channel 28

Acquisition Substate. 29

3. Use the measurement procedure defined in Section 2 to measure the radiated 30

spurious emissions of the mobile station receiver. 31


The mean radiated spurious power levels from the receiver, when measured using the 33

procedure in Section 2, shall not exceed the levels specified in Tables 3.6.2.3-1 and 34

3.6.2.3-2. 35

36

Deleted: band classes 0, 1, 2, 4, 5, 7, 8, 9, 10, 11 and 12

Deleted: 1893.5

3GPP2 C.S0011-C v2.0

3-91

Table 3.6.2.3-1. Maximum Allowable Radiated Spurious Emissions 1

for Band Classes 0, 1, 7, 10, 14 and 15 2

Frequency Range Maximum Allowable EIRP

30 to 88 MHz -55 dBm

88 to 216 MHz -52 dBm

216 to 960 MHz -49 dBm

960 MHz to 5 GHz (Band Classes 0,7, and 10) -41 dBm

960 MHz to 10 GHz (Band Class 1, 14 and 15) -41 dBm

3

Table 3.6.2.3-2. Maximum Allowable Radiated Spurious Emissions 4

for Band Classes 2, 3, 4, 5, 6, 8, 9, 11 and 12 5

Frequency Range Maximum Allowable EIRP

25 to 70 MHz -45 dBm

70 to 130 MHz -41 dBm

130 to 174 MHz -41 to -32 dBm*

174 to 260 MHz -32 dBm

260 to 470 MHz -32 to -26 dBm*

470 MHz to 5 GHz (Band Classes 2, 3, 5, 9, 11, and 12)

-21 dBm

470 MHz to 10 GHz (Band Classes 4, 6, and 8)

-21 dBm

1 GHz to 12.75 GHz (Band Class 6)

-6 dBm

*Interpolate linearly on a log frequency scale. 6

7


For example, a Band Class 7 mobile station operating under US regional requirements 9

shall limit radiated mean spurious emissions to less than –70 dBW/MHz EIRP in the GPS 10

band from 1559 to 1610 MHz. 11

Formatted Table

Deleted: and

Deleted: 960 to 2200 MHz

Deleted: -41 dBm

Deleted: 470 to 1000 MHz(band classes 2, 5, 9, 11and 12)

Deleted: -21 dBm

Deleted: 470 to 2200 MHz (band classes 4, 6 and 8)

Deleted: -21 dBm

Deleted: 470 to 3000 MHz (Band Class 3)

Deleted: -21 dBm

3GPP2 C.S0011-C v2.0

3-92

3.7 Supervision 1

3.7.1 Paging Channel or Forward Common Control Channel 2


These tests verify mobile station supervision when in the System Access State, where the 4

mobile station shall monitor the Paging Channel or Forward Common Control Channel at 5

all times per 2.6.3.1.8 of [6]. The mobile station shall set a timer for T72m seconds 6

whenever a valid message is received on the Paging Channel or Forward Common Control 7

Channel, whether addressed to the mobile station or not. For these tests, no valid 8

messages are sent after disabling of the Paging Channel or Forward Common Control 9

Channel. For Test 2, the Broadcast Control Channel is also disabled to ensure no valid 10

messages are received, even though the supervision requirement only applies to the 11

Forward Common Control Channel when in the System Access State. 12







3. Set the base station to ignore all access attempts. 19

4. Set the base station to disable access entry handoff, access probe handoff and 20

access handoff. 21

5. Set the test parameters as specified in Table 3.7.1.2-1. 22

6. Set the following parameters of the Access Parameters Message to the value 23

specified below: 24

25


NUM_STEP 15 (16 probes/sequence)

MAX_RSP_SEQ 15 (15 sequences)

26

7. Set the base station to send at least one valid message in every Paging Channel 27

slot. 28

8. Send a page to the mobile station on the Paging Channel. 29

9. Wait for two seconds and then disable the Paging Channel. 30

10. Monitor the mobile station output power (Test 1). 31

32

3GPP2 C.S0011-C v2.0

3-93

Table 3.7.1.2-1. Test Parameters for Supervision of Paging Channel 1

Parameter Units Value


orc

IEPilot dB -7

orc

IEPaging dB -16

PCH Data Rate bps 9600

2

11. If the mobile station supports the Forward Common Control Channel, perform 3



13. Set the following parameters of the Enhanced Access Parameters Message to the 6

value specified below: 7

8


EACH_NUM_STEP 15 (16 probes/sequence)


9

14. Set the base station to send at least one valid message in every Forward Common 10

Control Channel slot. 11

15. Send a page to the mobile station on the Forward Common Control Channel. 12

16. Wait for two seconds and then disable both the Forward Common Control Channel 13

and Broadcast Control Channel. 14


16

3GPP2 C.S0011-C v2.0

3-94

Table 3.7.1.2-2. Test Parameters for Supervision of Forward Common Control 1

Channel 2



or

cI

E Pilot dB -7

or

cI

E BCCH dB -15.7 (Rate = 1/4)

or

-15.2 (Rate = 1/2)

or

cI

E FCCCH dB -13.0 (Rate = 1/4)

or

-12.6 (Rate = 1/2)

BCCH Data Rate bps 9600 (80 ms)

FCCCH Data Rate bps 19200 (20 ms)

3


The mobile station shall transmit access attempts as a response to the page. The mobile 5

station shall stop transmitting access attempts between 0.92 seconds and 1.3 seconds 6

after the Paging Channel or Forward Common Control Channel is disabled. 7

3.7.2 Forward Traffic Channel with Power Control Subchannel on F-FCH or F-DCCH 8

This test shall be performed on the Forward Fundamental Channel and the Forward 9

Dedicated Control Channel if they are supported. The test shall be performed separately for 10

each supported channel. 11


During this test PUF, CDMA Candidate Frequency searches, Analog searches, and GPS 13

measurements shall be disabled. 14

Test 1a and Test 1b verify that the mobile station monitoring the Forward Traffic Channel 15

disables its transmitter after receiving a period of (N2m × 20) ms with insufficient signal 16

quality and re-enables its transmitter after receiving a period of (N3m × 20) ms with 17

sufficient signal quality and the mobile station does not declare a loss of the Forward 18

Traffic Channel if insufficient signal quality is received for a period of less than T5m 19

seconds. 20

Test 2 verifies that the mobile station monitoring the Forward Traffic Channel disables its 21

transmitter and declares a loss of the Forward Traffic Channel after receiving insufficient 22

signal quality for a period of T5m seconds. 23

3GPP2 C.S0011-C v2.0

3-95

Test 3 verifies that the mobile station does not disable its transmitter while receiving a 1

period of 2 seconds with sufficient signal quality with power control bits only, but no data. 2







3. If the mobile station supports demodulation of Radio Configuration 1 or 2 and does 9

not support demodulation of Radio Configuration 3, set up a call using 10

Fundamental Channel Test Mode 1 (see 1.3) with 9600 bps data rate only and 11


4. If the mobile station supports the Fundamental Channel and demodulation of 13

Radio Configuration 3, 4, or 5, set up a call using Fundamental Channel Test Mode 14


5. If the mobile station supports the Dedicated Control Channel and demodulation of 16

Radio Configuration 3, 4, or 5, set up a call using Dedicated Control Channel Test 17

Mode 3 (see 1.3) with 9600 bps data rate and 20 ms frame length and perform 18


6. If the mobile station supports the Fundamental Channel and demodulation of 20

Radio Configuration 6, 7, 8, or 9, set up a call using Fundamental Channel Test 21


7. If the mobile station supports the Dedicated Control Channel and demodulation of 23

Radio Configuration 6, 7, 8, or 9, set up a call using Dedicated Control Channel 24

Test Mode 7 (see 1.3) with 9600 bps data rate and 20 ms frame length and perform 25


8. Set the base station so as to not drop a call. 27

9. Set the test parameters as specified in Table 3.7.2.2-1. Forward Traffic Channel 28

open loop power control should be effectively disabled in the base station by setting 29

identical the outer loop setpoint values while achieving the specified test 30

conditions. 31

10. Send the Forward Fundamental Channel with 9600 bps data rate only or the 32

Forward Dedicated Control Channel with power control bits but no data (i.e. DCCH 33

frame activity = 0%). 34

11. Disable the transmission on the Forward Fundamental Channel or the Forward 35

Dedicated Control Channel starting at a frame boundary for exactly N2m × 0.02 36

seconds. When transmission is re-enabled, send the Forward Fundamental 37

Channel with 9600 bps data rate only or the Forward Dedicated Control Channel 38

with 9600 bps data rate (i.e. DCCH frame activity = 100%). 39

12. Monitor the mobile station output power (Test 1a). 40

3GPP2 C.S0011-C v2.0

3-96



Forward Dedicated Control Channel with power control bits but no data (i.e. DCCH 3

frame activity = 0%). 4

15. Disable the transmission of the Forward Fundamental Channel or the Forward 5

Dedicated Control Channel starting at a frame boundary for exactly (T5m - 0.2) 6




16. Monitor the mobile station output power (Test 1b). 10



Forward Dedicated Control Channel with 9600 bps data rate (i.e. DCCH frame 13

activity = 100%). 14

19. Disable the transmission of the Forward Fundamental Channel or the Forward 15

Dedicated Control Channel starting at a frame boundary for exactly (T5m + 0.2) 16





21. If the mobile station supports the Dedicated Control Channel, set up a call using 21

the same Dedicated Control Channel test mode used in Test 1 and 2. 22


23. Send 100 frames with power control bits only, but no data on the Forward 24

Dedicated Control Channel (i.e. frame activity = 0%), starting at a Forward Traffic 25

Channel frame boundary. 26


28


Power Control Subchannel on F-FCH or F-DCCH 30



orc

IEPilot dB -7

orc

IE Traffic

dB -16

31

3GPP2 C.S0011-C v2.0

3-97


Test 1a and Test 1b: 2

The mobile station shall disable its transmitter between N2m × 0.02 seconds and N2m 3

× 0.02 + 0.02 seconds after the Forward Traffic Channel is disabled. The mobile station 4

shall re-enable its transmitter between N3m × 0.02 seconds and N3m × 0.02 + 0.02 seconds 5

after the start of the first re-enabled Forward Traffic Channel frame. 6

Test 2: 7

The mobile station shall disable its transmitter after the Forward Traffic Channel is 8

disabled. In 90% of the trials with 95% confidence, the mobile station transmitter shall 9

remain disabled after Forward Traffic Channel is re-enabled. 10

Test 3: 11

The mobile station shall not disable its transmitter during the 2 seconds. 12

3.7.3 Forward Traffic Channel with Power Control Subchannel on CPCCH 13

This test shall be performed on the Forward Packet Data Channel, if supported. 14


During this test PUF, CDMA Candidate Frequency searches, Analog searches, and GPS 16

measurements shall be disabled. 17


transmitter after receiving a period of (N16m × 1.25) ms with insufficient signal quality and 19

re-enables its transmitter after receiving a period of (N17m × 1.25) ms with sufficient signal 20

quality and the mobile station does not declare a loss of the Forward Traffic Channel if 21

insufficient signal quality is received for a period of less than T5m seconds. 22


transmitter and declares a loss of the Forward Traffic Channel after receiving insufficient 24

signal quality for a period of T5m seconds. 25

Test 3 verifies that the mobile station does not disable its transmitter while receiving a 26

period of 4 seconds with sufficient signal quality with power control bits only, but no data. 27







3. Set up a call using Packet Data Channel Test Mode 10a (see 1.3) with CPCCH 34

subchannel assigned at 800 Hz. 35

4. Set the base station so as to not drop a call. 36

3GPP2 C.S0011-C v2.0

3-98

5. Set the test parameters as specified in Table 3.7.3.2-1. Forward Traffic Channel 1

open loop power control should be effectively disabled in the base station by setting 2

identical the outer loop setpoint values while achieving the specified test 3

conditions. 4


Power Control Subchannel on CPCCH 6



orc

IEPilot dB -7

orc

IE Traffic

dB -16

or

cI

E Control Power dB -16

7

6. Send power control bits on the subchannel of the Common Power Control Channel 8

assigned to the mobile station. 9

7. Disable the transmission on the Common Power Control Channel starting at a 10

power control bit assigned to the mobile station for exactly (T5m - 0.2) seconds. 11

When transmission is re-enabled, send the Common Power Control Channel. 12



10. Send power control bits on the subchannel of the Common Power Control Channel 15

assigned to the mobile station. 16

11. Disable the transmission on the Common Power Control Channel starting at a 17

power control bit assigned to the mobile station for exactly (T5m + 0.2) seconds. 18

When transmission is re-enabled, send power control bits on the subchannel of the 19

Common Power Control Channel assigned to the mobile station. 20


13. Set up a call using the same Packet Data Channel Test Mode 10a used in Test 1 22

and 2. 23


15. For 4 seconds, send power control bits only, but no data on the Forward Packet 25

Data Channel. 26


3GPP2 C.S0011-C v2.0

3-99


Test 1: 2

The mobile station shall disable its transmitter between N16m × 0.00125 seconds and N16m 3

× 0.00125 + 0.02 seconds after the Common Power Control Channel is disabled. The mobile 4

station shall re-enable its transmitter between N17m × 0.00125 seconds and N17m 5

× 0.00125 + 0.02 seconds after the Common Power Control Channel is re-enabled. 6

Test 2: 7

The mobile station shall disable its transmitter after the Common Power Control Channel is 8

disabled. In 90% of the trials with 95% confidence, the mobile station transmitter shall 9

remain disabled after Common Power Control Channel is re-enabled. 10

Test 3: 11

The mobile station shall not disable its transmitter during the 4 seconds. 12

3.8 Channel Quality Measurement Performance 13

3.8.1 Forward Link Channel Quality Measurement Accuracy Test 14

This test shall be performed on the Reverse Channel Quality Indicator Channel if the 15

Reverse Channel Quality Indicator Channel is supported by the mobile station. 16


The mobile station transmits Forward Pilot Channel C/I reports on the Reverse Channel 18

Quality Indicator Channel to indicate the quality of the forward link received from the 19

serving sector. The performance of the forward link pilot measurement accuracy is 20

determined by the bias and variance of the reported C/I values. 21



connector as shown in Figure 6.5.1.4. 24



3. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). 27

4. Configure the mobile station to use differential reporting mode 28

(FULL_CI_FEEDBACK_IND = ‘0’) and no repetition (REV_CQICH_REPS = ‘00’) on 29

the Reverse Channel Quality Indicator Channel. 30

3GPP2 C.S0011-C v2.0

3-100

5. Set the test parameters as specified below: 1

2



Îor /Ioc dB 0

orc

IE Pilot

dB -7

occ

IE Pilot

dB -7

Note: The Pilot Ec/Ioc value is calculated from the parameters in the table. It is not a directly settable parameter.

3

6. By setting the reverse power control bits, adjust the mobile station transmission 4

power so that no decoding errors on the Reverse Channel Quality Indicator 5

Channel are expected at the base station receiver. 6

7. Record the C/I values, as specified in [12], reported by the mobile station in every 7

Reverse Channel Quality Indicator Channel frame for at least 20 seconds. 8


The actual Ec/Io used in the test shall be within ±0.2 dB of the specified value. 10

Calculate the mean and standard deviation of the set of recorded C/I values. The input of 11

the statistical computation will be the recorded C/I value for every Reverse Channel 12

Quality Indicator Channel frame, expressed in units of dB. 13

The calculated mean C/I value shall be in the range from −8.1 dB to −6.3 dB. 14

The calculated standard deviation of the reported C/I values shall be no more than 1 dB. 15

16

17

3GPP2 C.S0011-C v2.0

4-1

4 CDMA TRANSMITTER MINIMUM STANDARDS 1

4.1 Frequency Accuracy 2

4.1.1 Definition 3

Frequency accuracy is the ability of a mobile station transmitter to transmit at an assigned 4

carrier frequency. 5

4.1.2 Method of Measurement 6

The method of measurement specified in 4.3.4.2 may be used to perform this test. 7

4.1.3 Minimum Standard 8

The mobile station output carrier frequency while transmitting in Band Class 0 shall be 9

within ±300 Hz of 45 MHz below the carrier frequency of the Forward CDMA Channel. 10






within ±300 Hz of 55 MHz above the carrier frequency of the Forward CDMA Channel. 16













The mobile station output carrier frequency while transmitting in Band Class 10 for CDMA 29

channel numbers, N, between 0 ≤ N ≤ 719 shall be within ±300 Hz of 45 MHz below the 30

carrier frequency of the Forward Channel. The mobile station output carrier frequency 31

while transmitting in Band Class 10 for CDMA channel numbers, N, between 720 ≤ N ≤ 32

919 shall be within ±300 Hz of 39 MHz below the carrier frequency of the Forward Channel. 33



3GPP2 C.S0011-C v2.0

4-2







7

4.2 Handoff 8

4.2.1 CDMA to CDMA Hard Handoff 9


The base station directs the mobile station to perform a CDMA to CDMA hard handoff by 11

sending a Universal Handoff Direction Message in which the mobile station is transitioned 12

between disjoint sets of base stations, different frequency assignments, or different frame 13

offsets. Hard handoff is characterized by a temporary disconnection of the Traffic Channel. 14

This test measures the time to execute a CDMA to CDMA hard handoff between Traffic 15

Channels belonging to different base stations (different pilot PN offset indices) with different 16

CDMA frequency assignments in the same band class. This test also verifies that the 17

mobile station disables its transmitter before changing frequency. 18




Channel from base station 1 has an arbitrary pilot PN offset index P1, a CDMA 22

frequency assignment f1(any valid value), and is called Channel 1. The Forward 23


frequency assignment f2 (any valid value other than f1in the same band class), and 25

is called Channel 2. Channel 2 shall be available at the action time specified in the 26

Universal Handoff Direction Message sent in step 7. 27








Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 6 through 8. 35



3GPP2 C.S0011-C v2.0

4-3


through 8. 2


7. Send a Universal Handoff Direction Message to the mobile station to set an explicit 4

action time and the following parameters: 5

6



PILOT_PN P2


CDMA_FREQ f2

7

8. Measure T1, the time elapsed from the action time to the instant the mobile station 8

transmit power, as measured at the mobile station antenna connector, on the old 9

CDMA frequency assignment drops below -61 dBm/MHz. Measure T2, the time 10

elapsed from the action time to the instant the mobile station transmitter is 11

enabled on the new CDMA frequency assignment. 12

13

Table 4.2.1.2-1. Test Parameters for CDMA to CDMA Hard Handoff 14


Îor dBm/1.23 MHz -75 -75

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7.4 -7.4

15


The mobile station transmit power shall remain under open loop and closed loop power 17

control until the action time. T1 shall be less than 2 ms. 18

T2 shall be less than T61m + (N11m + 2) × 20 ms = 140 ms. 19

4.2.2 Transmit Power after Hard Handoff 20


For RC1 and RC2, the mobile station output power is given by the following equation: 22

3GPP2 C.S0011-C v2.0

4-4

Pout = offset power – Pin + NOM_PWR – 16 × NOM_PWR_EXT + INIT_PWR 1

+ step number × PWR_STEP + Σpcb + interference correction. 2

For RC3 through RC6, the mobile station Pilot Channel output power is given by the 3

following equation: 4

R-Pilot-Pout = offset power – Pin + NOM_PWR – 16 × NOM_PWR_EXT + INIT_PWR 5

+ step number × PWR_STEP + Σpcb + interference correction. 6

Use the following nomenclature:: 7

Pout is the mobile transmit power in dBm, 8

R-Pilot-Pout is the mobile transmit power in dBm of the Pilot signal, 9

Pin is the mobile receiver power in dBm, 10

offset power is specified according to the following parameters 11

12

Band Class Spreading Rate Offset Power

3 1 (Access Channel) -73

1 (Enhanced Access Channel) -81.5

1 (Access Channel) -73


0, 2, 5, 7, 9, 10, 11 and 12

3 -76.5

1 (Access Channel) -76


1, 4, 6, 8, 14 and 15

3 -79.5

13

step number is the number of power steps needed in the access probe, 14

Σpcb is the summation of all Power Control Bits since starting transmission on the 15

traffic channel, and 16

interference correction is the noise floor correction (see 2.1.2.3.1 of [4]). 17

When changing channels from a serving frequency (f1) to a target frequency (f2), the 18

nominal transmit power should be the following for RC1 and RC2: 19

Pout(target) = Offset power(target) – Pin(target) + NOM_PWR(target) – 16 × 20

NOM_PWR_EXT(target) + INIT_PWR(serving) + step number × 21

PWR_STEP(serving) + Σpcb(serving) + interference correction (serving). 22

When changing channels from a serving frequency (f1) to a target frequency (f2), the 23

nominal transmit power should be the following for RC3 through RC6: 24

Deleted: and

3GPP2 C.S0011-C v2.0

4-5

R-Pilot-Pout(target) = Offset power(target) – Pin(target) + NOM_PWR(target) – 1

16 × NOM_PWR_EXT(target) + INIT_PWR(serving) + step number × 2

PWR_STEP(serving) + Σpcb(serving) + interference correction (serving) 3

The total power of the mobile is the sum of the Pilot Channel plus the R-FCH, which is at 4

full rate 9600 bps only for this test. In this case, the R-FCH is 3.75 dB above the Pilot 5

Channel, giving a total transmit power that is 5.28 dB above the Pilot Channel alone. See 6

2.1.2.3.3.2 of [4]. 7


Test 1 9




frequency assignment f1 (any valid value), and is called Channel 1. The Forward 13


frequency assignment f2 (any valid value other than f1), and is called Channel 2. 15

Channel 2 shall be available at the action time specified in the Universal Handoff 16

Direction Message sent in step 7. 17

















34

3GPP2 C.S0011-C v2.0

4-6



PILOT_PN P2


CDMA_FREQ f2

1

8. Measure the power, P, when the phone enables its transmitter on Channel 2. 2

3



Îor dBm/1.23 MHz -95 -65

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7.4 -7.4

INIT_PWR dB 0 0

NOM_PWR dB 0 0

NOM_PWR_EXT dB 0 0

PWR_STEP dB 0 0

5

Test 2 6




frequency assignment f1(any valid value), and is called Channel 1. The Forward 10


frequency assignment f2 (any valid value other than f1), and is called Channel 2. 12

Channel 2 shall be available at the action time specified in the Universal Handoff 13

Direction Message sent in step 7. 14




call on Channel 1 using Fundamental Channel Test Mode 1 (see 1.3) with 9600 bps 18

data rate only and perform steps 6 through 8. 19



3GPP2 C.S0011-C v2.0

4-7










10



PILOT_PN P2


CDMA_FREQ f2

11

8. Measure the power, P, when the phone enables its transmitter on Channel 2. 12

13



Îor dBm/1.23 MHz -75 -75

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7.4 -7.4

INIT_PWR dB 0 0

NOM_PWR dB +7 -8

NOM_PWR_EXT dB 0 0

PWR_STEP dB 0 0

15


Test 1 17

For Reverse RC1: 18

For Band Groups 450 and 800, the mobile transmit power, P, on Channel 2 shall be –8 19

dBm ± 10 dB. 20

Deleted: Band Classes 0, 2, 3, 5, 7, 9 and 10

3GPP2 C.S0011-C v2.0

4-8

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –11 dBm ± 10 1

dB. 2

For Reverse RC3: 3

For Band Groups 450 and 800, the mobile transmit power, P, on Channel 2 shall be –11.2 4

dBm ± 10 dB. 5

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –14.2 dBm ± 6

10 dB. 7

For Reverse RC5: 8


dBm ± 10 dB. 10

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –9.2 dBm ± 10 11

dB. 12

Test 2 13

For Reverse RC1: 14

For Band Groups 450 and 800, the mobile transmit power, P, on Channel 2 shall be –6 15

dBm ± 10 dB. 16

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –9 dBm ± 10 17

dB. 18

For Reverse RC3: 19


dBm ± 10 dB. 21

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –12.2 dBm ± 22

10 dB. 23

For Reverse RC5: 24


dBm ± 10 dB. 26

For Band Group 1900, the mobile transmit power, P, on Channel 2 shall be –7.2 dBm ± 10 27

dB. 28

4.3 Modulation Requirements 29

4.3.1 Time Reference 30


The mobile station time reference is derived from the earliest arriving multipath component 32

being used for demodulation. When receiving the Forward Traffic Channel, the mobile 33

station time reference shall be used as the transmit time of the Reverse Traffic Channel. 34

This test checks the accuracy of the mobile station time reference in static conditions as 35

well as the mobile station time reference slew rate in dynamic conditions. 36

Deleted: Band Classes 1, 4, 6 and 8


Deleted: Band classes 1, 4, 6 and 8




Deleted: Band Classes 1, 4, 6, and 8





3GPP2 C.S0011-C v2.0

4-9









only and perform steps 6 and 7. 9



Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 6 and 7. 12




and 7. 16


7. Determine the mobile station transmit time error at the mobile station antenna 18

connector using the ρ-meter described in 6.4.2. 19


Figure 6.5.1-1. The AWGN generator is not applicable in this test. The channel 21

simulator periodically generates two alternating paths which are 10 chips apart for 22

Spreading Rate 1 or 30 chips apart for Spreading Rate 3. Each of the two paths 23

lasts for 20 seconds and the alternating period is 40 seconds. 24



only and perform step 12. 27



Test Mode 3 (see 1.3) with 9600 bps data rate only and perform step 12. 30



Channel Test Mode 7 (see 1.3) with 9600 bps data rate only and perform step 12. 33

12. Determine the mobile station transmit time at the mobile station antenna 34

connector for a period of at least two minutes, and calculate the time reference 35

slew rate. 36

37

3GPP2 C.S0011-C v2.0

4-10

Table 4.3.1.2-1. Test Parameters for Time Reference 1



orc

IEPilot dB -7

orc

IE Traffic

dB -14

2


The mobile station time reference in steady state conditions shall be within ±1 μs of the 4

time of occurrence, as measured at the mobile station antenna connector, of the earliest 5

arriving multipath component being used for demodulation. 6

If a mobile station time reference correction is needed, it shall be corrected no faster than 7

203 ns in any 200 ms period and no slower than 305 ns per second when using Radio 8

Configuration 1 or 2. 9

If a mobile station time reference correction is needed, it shall be corrected no faster than 10

203 ns in any 200 ms period and no slower than 460 ns per second when using Radio 11

Configuration 3 through 9. 12

4.3.2 Reverse Pilot Channel to Code Channel Time Tolerance 13


When operating with Radio Configurations 3 through 6, the Reverse Pilot Channel to code 15

channel time tolerance is the permissible error in timing between the radiated Reverse Pilot 16

Channel and the other code channels. 17













3GPP2 C.S0011-C v2.0

4-11

5. Monitor the transmitter output with the code domain power test equipment as 1

described in 6.4.2.2 and measure the relative timing of the active channels. 2


When operating with Radio Configurations 3 through 6, the time error between the Reverse 4

Pilot Channel and all other code channels sharing the same Reverse CDMA Channel shall 5

be less than ±10 ns. 6

4.3.3 Reverse Pilot Channel to Code Channel Phase Tolerance 7


Reverse Pilot Channel to code channel phase tolerance is the permissible error in RF phase 9

between the radiated Reverse Pilot Channel and the other channels. 10













5. Monitor the transmitter output with the code domain power test equipment as 23

described in 6.4.2.2 and measure the relative phase of the active channels. 24


The phase differences between the Reverse Pilot Channel and all other code channels 26

sharing the same Reverse CDMA Channel should not exceed 0.05 radians and shall not 27

exceed 0.15 radians. 28

4.3.4 Waveform Quality and Frequency Accuracy 29


The waveform quality factor, ρ (see 6.4.2), is measured in this test. The measurement also 31

returns values for Δˆ f and τ , which are used to provide estimates of carrier frequency offset 32

and transmit time offset, respectively. 33

3GPP2 C.S0011-C v2.0

4-12









only and perform steps 4 and 5. 9


11



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

12

5. Measure the waveform quality factor, ρ, frequency error, Δˆ f , and transmit time 13

error, τ , at the mobile station antenna connector using the ρ-meter described in 14

6.4.2. 15



Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 8 through 18

11. 19




through 11. 23


25

3GPP2 C.S0011-C v2.0

4-13



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

1

9. Send a Universal Handoff Direction Message with a change to either the frame offset 2

or the PN offset, using the rest of the following parameters, to the mobile station to 3

force a hard handoff: 4

5



EXTRA_PARMS 1

FRAME_OFFSET may change

PILOT_PN may change

NOM_PWR_EXT 0 (0 dB correction)

NOM_PWR 0 (0 dB correction)

NUM_PREAMBLE 7 (20 ms preamble)

BAND_CLASS same as current

CDMA_FREQ same as current

6

10. Begin sending a periodic pattern of one ‘0’ power control bit followed by one ‘1’ 7

power control bit. 8

11. Measure the waveform quality factor, ρ, frequency error, Δˆ f , and transmit time 9

error, τ , at the mobile station antenna connector using the ρ-meter described in 10

6.4.2 on the preamble following the explicit action time of the Universal Handoff 11

Direction Message. 12


The waveform quality factor, ρ, shall be greater than 0.944 (excess power is less than 0.25 14

dB). The frequency error, Δˆ f , shall be within ±300 Hz while transmitting in Band Groups 15

450 and 800. The frequency error, Δˆ f , shall be within ±150 Hz while transmitting in Band 16

Group 1900. The transmit time error, τ , shall be within ±1 μs. 17

Deleted: band classes 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: band classes 1, 4, 6, and 8

3GPP2 C.S0011-C v2.0

4-14

4.3.5 Code Domain Power 1

The code domain power requirements for this test are applicable to inactive code channels 2

only. 3


Code domain power is a measure of the power in each code channel of a CDMA Channel. 5

The CDMA time reference used in the code domain power test is derived from the Pilot 6

Channel and is used as the reference for demodulation of all other code channels. 7









Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 5 and 6. 16




and 6. 20


22



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

23

6. Measure the mobile station transmitter output at the antenna connector with a 24

Code Domain Power Analyzer described in 6.4.2.2.5, with Walsh function length, 25

N, set to 16. 26


Both the real and imaginary components of code domain power in each inactive code 28

channel shall be 23 dB or more below the total output power measured on both the I and Q 29

carrier phase components combined. When either component of a code channel is active, 30

the whole code channel is considered active, and this requirement shall not apply. 31

3GPP2 C.S0011-C v2.0

4-15

4.4 RF Output Power Requirements 1

4.4.1 Range of Open Loop Output Power 2


The mobile station estimates its open loop mean output power from its mean input power, 4

which is referenced to the nominal CDMA Channel bandwidth of 1.23 MHz for Spreading 5

Rate 1 or 3.69 MHz for Spreading Rate 3. 6

When transmitting on the Access Channel, the estimate is defined as 7

mean output power (dBm) = - mean input power (dBm) 8

+ offset power 9

+ interference correction 10

+ NOM_PWR - 16 × NOM_PWR_EXT 11

+ INIT_PWR. 12

where the offset power is summarized below: 13

14

Band Groups Offset Power

450 and 800 -73

1900 -76

15

When transmitting on the Enhanced Access Channel, the estimate is defined as 16

mean pilot channel output power (dBm) = - mean input power (dBm) 17

+ offset power 18

+ interference correction 19

+ NOM_PWR_EACH 20

+ INIT_PWR_EACH. 21

where the offset power is summarized below: 22

23

Band Groups Spreading Rate Offset Power

1 -81.5 450 and 800

3 -76.5

1 -84.5 1900

3 -79.5

note: SR3 is not defined for BC 3 (in Band Group 800). 24

This test measures the range of the estimated open loop output power. 25

Deleted: Band Class

Deleted: 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: 1, 4, 6 and 8

Deleted: Band Class

Deleted: 3

Deleted: 1

Deleted: -81.5

Deleted: 0, 2, 5, 7, 9, 10, 11 and 12


3GPP2 C.S0011-C v2.0

4-16


4.4.1.2.1 Access Channel 2

1. Configure the base station so that the mobile station uses the Access Channel. 3






4. Set the parameter values in the Access Parameters Message to the values specified 9

below. 10

11


PAM_SZ 15 (16 frames)

MAX_RSP_SEQ 1 (1 sequence)

12

5. Set the test parameter for Test 1 as specified in Table 4.4.1.2.1-1 and perform 13







9. Send a page to the mobile station. 20

10. Measure the output power of the mobile station at the antenna connector during 21

transmission of a probe. 22

23

3GPP2 C.S0011-C v2.0

4-17

Table 4.4.1.2.1-1. Test Parameter of Îor for Range of Open Loop Output Power 1

for the Access Channel 2

Band Class

Mobile Station Class

Unit Test 1 Test 2 Test 3

Class I dBm -25 -65 -103.0

Class II dBm -25 -65 -98.3 0, 3, 9 and 12

Class III dBm -25 -65 -93.5

Class I dBm -25 -65 -103.0

Class II dBm -25 -65 -97.0


Class IV dBm -25 -65 -86.1

1, 4, 6, 8, 14 and

15

Class V dBm -25 -65 -81.0

Class II dBm -25 -65 -103.0


2

Class IV dBm -25 -65 -93.5

Class I dBm -25 -65 -99.7

Class II dBm -25 -65 -98.3


5 and 11

Class IV dBm -25 -65 -88.1

7 and 10 Class I dBm -25 -65 -98.3

Class II dBm -25 -65 -93.5

3

4.4.1.2.2 Enhanced Access Channel 4






3. For each Enhanced Access Channel spreading rate that the mobile station 10

supports, perform steps 4 through 13. 11

4. Set the parameter values in the Enhanced Access Parameters Message to the values 12

specified below. 13

14

Deleted: and

3GPP2 C.S0011-C v2.0

4-18


REACH_RATE_MODE 0 (9600 bps, 20 ms frame size)

REACH_MODE 0 (Basic Access Mode - no CACH or CPCCH)

EACH_PREAMBLE_NUM_FRAC 0 (no preamble)

EACH _PREAMBLE_ADD_DURATION 0 (no additional preamble)

EACH_MAX_RSP_SEQ 1 (1 sequence)

1















13. Measure the output power of the mobile station at the antenna connector during 16

transmission of a probe. 17

18

3GPP2 C.S0011-C v2.0

4-19

Table 4.4.1.2.2-1. Test Parameter of Îor for Range of Open Loop Output Power for the 1

Spreading Rate 1 Enhanced Access Channel 2

Band Class



Class I dBm -25 -65 -103.0

Class II dBm -25 -65 -98.3 0, 3, 9 and 12


Class I dBm -25 -65 -103.0

Class II dBm -25 -65 -97.0


Class IV dBm -25 -65 -86.1

1, 4, 6, 8, 14 and

15

Class V dBm -25 -65 -81.0

Class II dBm -25 -65 -103.0


2

Class IV dBm -25 -65 -93.5

Class I dBm -25 -65 -99.7

Class II dBm -25 -65 -98.3


5 and 11

Class IV dBm -25 -65 -88.1

7 and 10 Class I dBm -25 -65 -98.3

Class II dBm -25 -65 -93.5

3

Deleted: and

3GPP2 C.S0011-C v2.0

4-20

Table 4.4.1.2.2-2. Test Parameter of Îor for Range of Open Loop Output Power for the 1


Band Class



Class I dBm -20 -60 -98.0

Class II dBm -20 -60 -93.3 0, 9 and

12 Class III dBm -20 -60 -88.5

Class I dBm -20 -60 -98.0

Class II dBm -20 -60 -92.0


Class IV dBm -20 -60 -81.1

1, 4, 6, 8, 14 and

15

Class V dBm -20 -60 -76.0

Class II dBm -20 -60 -98.0

2 Class III dBm -20 -60 -93.3

Class IV dBm -20 -60 -88.5

Class I dBm -20 -60 -94.7

5 and 11 Class II dBm -20 -60 -93.3


Class IV dBm -20 -60 -83.1

7 and 10 Class I dBm -20 -60 -93.3

Class II dBm -20 -60 -88.5

3


If the mobile station supports the Access Channel, the mobile station output power shall 5

satisfy the range specified in Table 4.4.1.3-1. 6

If the mobile station supports the Spreading Rate 1 Enhanced Access Channel, the mobile 7

station output power shall satisfy the range specified in Table 4.4.1.3-2. 8

If the mobile station supports the Spreading Rate 3 Enhanced Access Channel, the mobile 9

station output power shall satisfy the range specified in Table 4.4.1.3-3. 10

11

Deleted: and

3GPP2 C.S0011-C v2.0

4-21


Access Channel 2

Band Class


Units Test 1 Test 2 Test 3

Class I dBm -48 ± 9.5 -8 ± 9.5 27 ± 9.5

Class II dBm -48 ± 9.5 -8 ± 9.5 24 ± 9.5 0, 3, 9 and 12

Class III dBm -48 ± 9.5 -8 ± 9.5 20 ± 9.5

Class I dBm -51 ± 9.5 -11 ± 9.5 24 + 9/- 9.5

Class II dBm -51 ± 9.5 -11 ± 9.5 20 ± 9.5

Class III dBm -51 ± 9.5 -11 ± 9.5 15 ± 9.5

Class IV dBm -51 ± 9.5 -11 ± 9.5 10 ± 9.5

1, 4, 6, 8, 14 and

15

Class V dBm -51 ± 9.5 -11 ± 9.5 5 ± 9.5

Class II dBm -48 ± 9.5 -8 ± 9.5 27 ± 9.5

Class III dBm -48 ± 9.5 -8 ± 9.5 24 ± 9.5

2

Class IV dBm -48 ± 9.5 -8 ± 9.5 20 ± 9.5

Class I dBm -48 ± 9.5 -8 ± 9.5 25 ± 9.5

Class II dBm -48 ± 9.5 -8 ± 9.5 24 ± 9.5

Class III dBm -48 ± 9.5 -8 ± 9.5 20 ± 9.5

5 and 11

Class IV dBm -48 ± 9.5 -8 ± 9.5 15 ± 9.5

7 and 10 Class I dBm -48 ± 9.5 -8 ± 9.5 24 ± 9.5

Class II dBm -48 ± 9.5 -8 ± 9.5 20 ± 9.5

3

Deleted: and

3GPP2 C.S0011-C v2.0

4-22



Band Class



Class I dBm -51.2 ± 9.5 -11.2 ± 9.5 23.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5 0, 3, 9 and 12

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

Class I dBm -54.2 ± 9.5 -14.2 ± 9.5 20.8 ± 9.5

Class II dBm -54.2 ± 9.5 -14.2 ± 9.5 16.8 ± 9.5

Class III dBm -54.2 ± 9.5 -14.2 ± 9.5 11.8 ± 9.5

Class IV dBm -54.2 ± 9.5 -14.2 ± 9.5 6.8 ± 9.5

1, 4, 6, 8, 14 and

15

Class V dBm -54.2 ± 9.5 -14.2 ± 9.5 1.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 23.8 ± 9.5

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

2

Class IV dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

Class I dBm -51.2 ± 9.5 -11.2 ± 9.5 21.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

5 and 11

Class IV dBm -51.2 ± 9.5 -11.2 ± 9.5 11.8 ± 9.5

7 and 10 Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

3

Deleted: and

3GPP2 C.S0011-C v2.0

4-23



Band Class



Class I dBm -51.2 ± 9.5 -11.2 ± 9.5 23.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5 0, 9 and

12 Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

Class I dBm -54.2 ± 9.5 -14.2 ± 9.5 20.8 ± 9.5

Class II dBm -54.2 ± 9.5 -14.2 ± 9.5 16.8 ± 9.5

Class III dBm -54.2 ± 9.5 -14.2 ± 9.5 11.8 ± 9.5

Class IV dBm -54.2 ± 9.5 -14.2 ± 9.5 6.8 ± 9.5

1, 4, 6, 8, 14 and

15

Class V dBm -54.2 ± 9.5 -14.2 ± 9.5 1.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 23.8 ± 9.5

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

2

Class IV dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

Class I dBm -51.2 ± 9.5 -11.2 ± 9.5 21.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

Class III dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

5 and 11

Class IV dBm -51.2 ± 9.5 -11.2 ± 9.5 11.8 ± 9.5

7 and 10 Class I dBm -51.2 ± 9.5 -11.2 ± 9.5 20.8 ± 9.5

Class II dBm -51.2 ± 9.5 -11.2 ± 9.5 16.8 ± 9.5

3

4.4.2 Time Response of Open Loop Power Control 4


Following a step change in the mean input power, the mean output power of the mobile 6

station changes as a result of the open loop power control. This test measures the open 7

loop power control time response to a step change in the mean input power. 8







Deleted: and

3GPP2 C.S0011-C v2.0

4-24






Test Mode 3 (see 1.3) with 9600 bps data rate only and perform steps 6 through 6

11. 7




through 11. 11


7. Send alternating ‘0’ and ‘1’ power control bits on the Forward Power Control 13

Subchannel. 14

8. Change the input power by a step of +20 dB and measure the transmitted output 15

power as a function of time after the step change for 100 ms. 16

9. Change the input power by a step of -20 dB and measure the transmitted output 17


10. Change the input power by a step of -20 dB and measure the transmitted output 19


11. Change the input power by a step of +20 dB and measure the transmitted output 21


23

Table 4.4.2.2-1. Test Parameters for Time Response of Open Loop Power Control 24



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

25

3GPP2 C.S0011-C v2.0

4-25


Following a step change in mean input power, ΔPin, the mean output power of the mobile 2

station shall transition to its final value in a direction opposite in sign to ΔPin, with 3

magnitude contained between mask limits11 defined by: 4

(a) upper limit: 5

for 0 < t < 24 ms: max [1.2 × |ΔPin| × (t/24), |ΔPin| × (t/24) + 2.0 dB] + 1.5 dB, 6

for t ≥ 24 ms: max [1.2 × |ΔPin|, |ΔPin| + 0.5 dB] + 1.5 dB; 7

(b) lower limit: 8

for t > 0: max [0.8 × |ΔPin| × [1 - e(1.25 - t)/36] - 2.0 dB, 0] - 1 dB; 9

where t is expressed in units of milliseconds, ΔPin is expressed in units of dB, and max 10

[x,y] is the maximum of x and y. Figure 4.4.2.3-1 shows the limits for ΔPin = 20 dB. The 11

absolute value of the change in mean output power due to open loop power control shall be 12

a monotonically increasing function of time. If the change in mean output power consists of 13

discrete increments, no single increment due to open loop power control shall exceed 1.2 14

dB. 15

16

-

0

5

10

15

20

25

30

0 10 20 30 40 50 60 70 80 90 100

t (ms)

OutputPowerChange[dB]

17

18

Figure 4.4.2.3-1. Upper and Lower Limits for Open Loop Power Control Step Response 19

for ΔPin = 20 dB 20

21

11 The mask limits can be approximated by a piece-wise linear approximation. The mask limits allow for the effect of alternating closed loop power control bits.

3GPP2 C.S0011-C v2.0

4-26

4.4.3 Access Probe Output Power 1

These tests shall be performed for each of the Access Channel, Spreading Rate 1 Enhanced 2

Access Channel and Spreading Rate 3 Enhanced Access Channel that the mobile station 3

supports. 4


This test verifies the following Access Channel and Enhanced Access Channel parameters: 6

nominal power offset, initial power offset, power increment from the estimated open loop 7

output power, number of access probes in one probe sequence, and the number of probe 8

sequences in one mobile station page response access attempt. 9


4.4.3.2.1 Access Channel Probe 11






3. Set Îor to -65 dBm /1.23 MHz and Pilot Ec/Ior to –5 dB. 17

4. Set the parameter MAX_RSP_SEQ in the Access Parameters Message to one. 18


6. Send a page to the mobile station on the Paging Channel. 20

7. Measure and record the mobile station mean output power for each probe at the 21

antenna connector. Note that the mean output power is the average power of the 22

access probe measured over the entire access probe duration. 23

8. Change the parameter values in the Access Parameters Message to the values 24

specified below. Repeat steps 6 and 7. 25

26


NOM_PWR 3 (3 dB)

INIT_PWR 3 (3 dB)

PWR_STEP 3 (3 dB/step)

NUM_STEP 2 (3 probes/sequence)


27

3GPP2 C.S0011-C v2.0

4-27

4.4.3.2.2 Enhanced Access Channel Probe 1




2. For each Enhanced Access Channel spreading rate supported by the mobile 5

station, perform steps 3 through 9. 6



4. Set Îor to -65 dBm /1.23 MHz and Pilot Ec/Ior to –5 dB. 9

5. Set the parameter MAX_RSP_SEQ in the Enhanced Access Parameters Message to 10

one. 11


7. Send a page to the mobile station on the Forward Common Control Channel. 13

8. Measure and record the mobile station mean output power for each Enhanced 14

Access Channel access probe at the antenna connector. Note that the mean output 15

power is the average power of the access probe measured over the entire access 16

probe duration. 17

9. Change the parameter values in the Enhanced Access Parameters Message to the 18

values specified below. Repeat steps 6 through 8. 19

20


EACH_NOM_PWR 3 (3 dB)

EACH_INIT_PWR 3 (3 dB)

EACH_PWR_STEP 3 (3 dB/step)

EACH_NUM_STEP 2 (3 probes/sequence)


21


For each Access Channel, Spreading Rate 1 Enhanced Access Channel and Spreading Rate 23

3 Enhanced Access Channel supported by the mobile station, the mobile station shall meet 24

the following requirements: 25

In the first access attempt: 26

(a) The mean power of the first access probe shall be within ±9.5 dB of the expected 27

value. 28

(b) The mean power of the subsequent access probes shall be within a range of ±1.2 dB 29

of the first probe. 30

3GPP2 C.S0011-C v2.0

4-28

(c) The number of access probes in an access probe sequence shall be five. 1

(d) There shall be one access probe sequence in the page response access attempt. 2

In the second access attempt: 3

(a) The mean power of the first access probe of each access probe sequence shall be 6 ± 4

2.4 dB above the power of the access probes in the first access scenario. 5

(b) The difference in the value of the mean output power of the second probe of the 6

sequence and the first probe of the sequence shall be 3 ± 1.8 dB. The difference in 7

the value of the mean output power of the third probe of the sequence and the first 8

probe of the sequence shall be 6 ± 2.4 dB. 9

(c) The number of access probes in each access probe sequence shall be three. 10

(d) The number of access probe sequences in the page response access attempt shall be 11

three. 12

(e) The Access Channel probes shall be randomized as specified in Section 2.1.1.2.2 of 13

[5] and Section 2.2.4.4.2.1.4 of [6]. 14

4.4.4 Range of Closed Loop Power Control 15


The mobile station provides a closed loop adjustment to its open loop estimate. 17

Adjustments are made in response to valid received power control bits. The range of the 18

adjustment is defined by the difference between the maximum mobile station output power 19

and the open loop estimate, and the difference between the minimum mobile station output 20

power and the open loop estimate. 21



Figure 6.5.1-4. The AWGN generator and the interference generator are not applicable in 24

this test. 25



3. Set the power control step size to 1 dB. Perform steps 6 through 23. 28

4. If the mobile station supports a power control step size of 0.5 dB, set the power 29

control step size to 0.5 dB and perform steps 6 through 23. 30

5. If the mobile station supports a power control step size of 0.25 dB, set the power 31

control step size to 0.25 dB and perform steps 6 through 23. 32

6. If the mobile station supports demodulation of Radio Configuration 1 or 2, perform 33

steps 7 through 17 using Fundamental Channel Test Mode 1 (see 1.3). 34

7. Set up a call using the Fundamental Channel test mode or Dedicated Control 35

Channel test mode (see 1.3) with 9600 bps data rate only. 36

3GPP2 C.S0011-C v2.0

4-29

8. Set the attenuation in the Forward CDMA Channel to yield an open loop output 1

power, measured at the mobile station antenna connector, of -15 dBm and perform 2

step 10. Tests 1, 6 and 10 specify the power control step size to be equal to 1 dB, 3

0.5 dB, and 0.25 dB, respectively. 4

9. If the power control step size is 1 dB, set the attenuation in the Forward CDMA 5

Channel to yield an open loop output power, measured at the mobile station 6

antenna connector, of 19 dBm (Test 2) and perform step 10. 7

10. Measure the mobile station output power while transmitting alternating ‘0’ and ‘1’ 8

power control bits (the last bit is a ‘1’ bit), followed by 100 consecutive ‘0’ power 9

control bits, followed by 100 consecutive ‘1’ power control bits, and followed by 100 10

consecutive ‘0’ power control bits. 11

11. Set up a call using the Fundamental Channel test mode (see 1.3) with 4800 bps 12

data rate only. 13


power, measured at the mobile station antenna connector, of -15 dBm when the 15

mobile station transmitter is gated on and perform step 17. Tests 3, 7 and 11 16

specify the power control step size to be equal to 1 dB, 0.5 dB, and 0.25 dB, 17

respectively. 18


data rate only. 20





respectively. 25


data rate only. 27



mobile station transmitter is gated on and perform steps 17. Tests 5, 9 and 13 30


respectively. 32

17 Measure the mobile station output power while transmitting alternating ‘0’ and ‘1’ 33

valid power control bits (the last bit is a ‘1’ bit), followed by 100 consecutive ‘0’ 34

valid power control bits, followed by 100 consecutive ‘1’ valid power control bits, 35

and followed by 100 consecutive ‘0’ valid power control bits. Set all invalid power 36

control bits to ‘0’. 37

18. If the mobile station supports the demodulation of Radio Configuration 3, 4, or 5, 38

perform steps 20 through 23 using Fundamental Channel Test Mode 3 or if the 39

Forward Fundamental Channel is not supported, perform steps 20 through 23 40

using the Dedicated Control Channel Test Mode 3 (see 1.3). 41

3GPP2 C.S0011-C v2.0

4-30


perform steps 20 through 23 using Fundamental Channel Test Mode 7 or if the 2

Forward Fundamental Channel is not supported, perform steps 20 through 23 3

using the Dedicated Control Channel Test Mode 7 (see 1.3). 4

20. Perform steps 7 through 10. 5

21. If the mobile station supports Reverse Fundamental Channel gating, set up a call 6

using the Fundamental Channel test mode (see 1.3) with 1500 bps data rate only. 7





respectively. 12

23. Measure the mobile station output power while transmitting alternating ‘0’ and ‘1’ 13

valid power control bits (the last bit is a ‘1’ bit), followed by 100 consecutive ‘0’ 14

valid power control bits, followed by 100 consecutive ‘1’ valid power control bits, 15

and followed by 100 consecutive ‘0’ valid power control bits. Set all invalid power 16

control bits to ‘0’. 17


The average rate of change in mean output power requirement specified below applies to 19

mobile station output power up to 3 dB below the lower limit of the maximum output 20

power specified in Table 4.4.5.3-1. 21

Test 1: 22

(a) The closed loop power control range shall be at least ±24 dB around the open loop 23

estimate. 24

(b) The interval from the end of the first valid ‘1’ power control bit after the 100 25

consecutive ‘0’ valid power control bits to the time the mobile station output power 26

starts to decrease shall be no longer than 2.5 ms. 27

(c) The average rate of change in mean output power for 9600 bps data rate shall be 28

greater than 12.8 dB per 20 ms and less than 19.2 dB per 20 ms. 29

(d) Following the reception of any valid power control bit that occurs 2.5 ms after the 30

100 consecutive '0' valid power control bits, the mean output power of the mobile 31

station shall be within 0.3 dB of its final value in less than 500 μs. 32

Test 2: 33

(a) The interval from the end of the first valid ‘1’ power control bit after the 100 34

consecutive ‘0’ valid power control bits until the time the mobile station output 35

power starts to decrease shall be no longer than 2.5 ms. 36

Test 3: 37


estimate. 39

3GPP2 C.S0011-C v2.0

4-31



power starts to decrease shall be no longer than 5 ms. 3



Test 4: 6


estimate. 8






Test 5: 14


estimate. 16






Test 6: 22

(a) The average rate of change in mean output power for 9600 bps data rate shall be 23

greater than 12 dB per 40 ms and less than 20 dB per 40 ms. 24

(b) Following the reception of any valid power control bit that occurs 2.5 ms after the 25



Test 7: 28


greater than 6.0 dB per 40 ms and less than 10 dB per 40 ms. 30

Test 8: 31



Test 9: 34



Test 10: 37

3GPP2 C.S0011-C v2.0

4-32



(b) Following the reception of any valid power control bit bit that occurs 2.5 ms after the 3



Test 11: 6



Test 12: 9



Test 13: 12



Test 14: 15


estimate. 17






Test 15: 23


greater than 6.0 dB per 40 ms and less than 10 dB per 40 ms. 25

Test 16: 26



4.4.5 Maximum RF Output Power 29


For each Reverse Traffic Channel Radio Configuration that the mobile station supports, the 31

maximum radiated RF output power is determined by the measurement of the maximum 32

power that the mobile station transmits as measured at the mobile station antenna 33

connector plus the antenna gain recommended by the mobile station manufacturer. The 34

antenna gain is determined from the Radiated Signal Measurement Procedures (see 2.6) 35

and calculating the antenna gain for EIRP or ERP as appropriate. 36

3GPP2 C.S0011-C v2.0

4-33







3. If the mobile station supports Reverse Traffic Channel Radio Configuration 1 and 7

Forward Traffic Channel Radio Configuration 1, set up a call using Fundamental 8


through 8 (Test 1). 10

4. If the mobile station supports the Radio Configuration 3 Reverse Fundamental 11

Channel and demodulation of Radio Configuration 3, 4, or 5, set up a call using 12


perform steps 6 through 8 (Test 2). 14

5. If the mobile station supports the Radio Configuration 3 Reverse Dedicated Control 15


Dedicated Control Channel Test Mode 3 (see 1.3) with 9600 bps data rate and 17

100% frame activity and perform steps 6 through 8 (Test 3). 18


7. Send continuously ‘0’ power control bits to the mobile station. 20

8. Measure the mobile station output power at the mobile station antenna connector. 21


Channel, Radio Configuration 3 Reverse Dedicated Control Channel and 23

demodulation of Radio Configuration 3, 4, or 5, set up a call using Fundamental 24

Channel Test Mode 3 (see 1.3) with 1500 bps Fundamental Channel data rate only 25

and 9600 bps Dedicated Control Channel with 100% frame activity, and perform 26

steps 12 through 19 or steps 20 through 27 (Test 4). 27


Channel, Radio Configuration 3 Reverse Supplemental Channel 0 and 29

demodulation of Radio Configuration 3, 4, or 5, set up a call using Supplemental 30

Channel Test Mode 3 (see 1.3) with 9600 bps Fundamental Channel and 9600 bps 31

Supplemental Channel 0 data rate, and perform steps 12 through 19 or steps 20 32





Channel Test Mode 3 (see 1.3) with 9600 bps Dedicated Control Channel with 37

100% frame activity and 9600 bps Supplemental Channel 0 data rate, and perform 38


12. Set the test parameters as specified in Table 4.4.5.2-2 and Table 4.4.5.2-3. 40

3GPP2 C.S0011-C v2.0

4-34

13. Send alternating ‘0’ and ‘1’ power control bits to the mobile station using the 1

smallest supported closed loop power control step size supported by the mobile 2

station. 3

14. Determine the active channel configuration (the channel configuration observed 4

during the measurement). If the desired channel configuration (the channel 5

configuration specified for the test) is not the active channel configuration, increase 6

Îor by 1 dB and repeat the verification. Repeat this step until the desired channel 7

configuration becomes active. 8


16. Decrease Îor by 0.5 dB. 10

17. Determine the active channel configuration. If the active channel configuration is 11

the desired channel configuration, measure the mobile station output power at the 12


18. Repeat steps 16 and 17 until the output power no longer increases or the desired 14

channel configuration is no longer active. Record the highest output power 15

achieved with the desired channel configuration active. 16

19. Repeat steps 12 through 18 ten times and average the results. 17


21. Set the base station to use normal power control using the smallest supported 19

closed loop power control step size supported by the mobile station. 20

22. Determine the active channel configuration. If the desired channel configuration is 21

not the active channel configuration, decrease the power control set point at the 22

base station in 1 dB steps until the desired channel configuration is the active 23

channel configuration. The power control set point is the desired mobile station 24

output power level set at the base station simulator. 25


24. Increase the power control set point at the base station by 0.5 dB. 27









Channel and demodulation of Radio Configuration 6, 7, 8, or 9, set up a call using 36



3GPP2 C.S0011-C v2.0

4-35










demodulation of Radio Configuration 6, 7, 8, or 9, set up a call using Fundamental 10



steps 36 through43 (Test 9). 13



demodulation of Radio Configuration 6, 7, 8, or 9, set up a call using Supplemental 16


Supplemental Channel 0 data rate, and perform steps 36 through 43 (Test 10). 18






steps 36 through 43 (Test 11). 24




station. 28


not active, increase Îor by 1 dB. Repeat this step until the desired channel 30











3GPP2 C.S0011-C v2.0

4-36

1

Table 4.4.5.2-1. Test Parameters for Maximum RF Output Power with a Single Traffic 2

Code Channel, Spreading Rate 1 3



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

4

Table 4.4.5.2-2. Test Parameters for Maximum RF Output Power with Multiple Traffic 5

Code Channels, Spreading Rate 1 6


orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

7

3GPP2 C.S0011-C v2.0

4-37

Table 4.4.5.2-3. Îor Values for Maximum RF Output Power with Multiple Traffic Code 1

Channels, Spreading Rate 1 2

Îor (dBm/1.23 MHz) Band Class Mobile Station Class

Test 4 Test 5 Test 6

Class I -95.4 -93.4 -93.9

Class II -91.4 -89.4 -89.9 0, 3, 9 and

12 Class III -87.4 -85.4 -85.9

Class I -95.4 -93.4 -93.9

Class II -90.4 -88.4 -88.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

1, 4, 8, 14 and 15

Class V -75.4 -73.4 -73.9

Class I -95.4 -93.4 -93.9

Class II -90.4 -88.4 -88.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

6 (outside Japan)

Class V -75.4 -73.4 -73.9

Class I and II -84.4 -82.4 -82.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

6 (in Japan)

Class V -75.4 -73.4 -73.9

Class II -95.4 -93.4 -93.9

2 Class III -91.4 -89.4 -89.9

Class IV -87.4 -85.4 -85.9

Class I -97.4 -95.4 -95.9

Class II -92.4 -90.4 -90.9

Class III -87.4 -85.4 -85.9

5 and 11

Class IV -82.4 -80.4 -80.9

7 and 10 Class I -91.4 -89.4 -89.9

Class II -87.4 -85.4 -85.9

3

Deleted: and

3GPP2 C.S0011-C v2.0

4-38

Table 4.4.5.2-4. Test Parameters for Maximum RF Output Power with a Single Traffic 1

Code Channel, Spreading Rate 3 2



orc

IEPilot dB -10

orc

IE Traffic

dB -12.4

3

Table 4.4.5.2-5. Test Parameters for Maximum RF Output Power with Multiple Traffic 4

Code Channels, Spreading Rate 3 5



orc

IEPilot dB -10

orc

IE Traffic

dB -12.4

6


For each radio configuration that the mobile station supports, the maximum output power 8

of each mobile station class shall be such that the maximum radiated power for the mobile 9

station class using the antenna gain recommended by the mobile station manufacturer is 10

within the limits specified in Table 4.4.5.3-1. The antenna gain is determined using the 11

Radiated Signal Measurement Procedures (see 2.6) and calculating the antenna gain for 12

EIRP or ERP as appropriate. When the mobile station is transmitting using one of the test 13

mode channel configurations specified in Table 4.4.5.3-2, the maximum output power 14

requirements of the mobile station specified in Table 4.4.5.3-1 may be reduced by the 15

applicable output power backoff allowance specified in Table 4.4.5.3-2. 16

17

3GPP2 C.S0011-C v2.0

4-39

Table 4.4.5.3-1. Effective Radiated Power at Maximum Output Power 1

Band Class Mobile Station Class

Radiating Measurement

Lower Limit Upper Limit

Class I ERP 1 dBW (1.25 W) 8 dBW (6.3 W)

Class II ERP -3 dBW (0.5 W) 4 dBW (2.5 W) 0, 3, 9 and

12 Class III ERP -7 dBW (0.2 W) 0 dBW (1.0 W)

Class I EIRP -2 dBW (0.63 W) 3 dBW (2.0 W)

Class II EIRP -7 dBW (0.2 W) 0 dBW (1.0 W)

Class III EIRP -12 dBW (63 mW) -3 dBW (0.5 W)

Class IV EIRP -17 dBW (20 mW) -6 dBW (0.25 W)

1, 4, 8, 14 and 15

Class V EIRP -22 dBW (6.3 mW) -9 dBW (0.13 W)

Class I EIRP -2 dBW (0.63 W) 3 dBW (2.0 W)

Class II EIRP -7 dBW (0.2 W) 0 dBW (1.0 W)



6 (outside Japan)


Class I and II EIRP -10 dBW (0.1 W) -6 dBW (0.25 W)



6 (in Japan)


Class II ERP 1 dBW (1.25 W) 8 dBW (6.3 W)

2 Class III ERP -3 dBW (0.5 W) 4 dBW (2.5 W)

Class IV ERP -7 dBW (0.2 W) 0 dBW (1.0 W)

Class I ERP 3 dBW (2.0 W) 10 dBW (10 W)

Class II ERP -2 dBW (0.63 W) 5 dBW (3.2 W)

Class III ERP -7 dBW (0.2 W) 0 dBW (1.0 W)

5 and 11

Class IV ERP -12 dBW (63 mW) -5 dBW (320 mW)

7 and 10 Class I ERP -3 dBW (0.5 W) 4 dBW (2.5 W)

Class II ERP -7 dBW (0.2 W) 0 dBW (1.0 W)

For Band Class 6 operation, the mobile station should use country code information in the overhead messages to determine the correct maximum radiated power allowed.

2

Deleted: and

3GPP2 C.S0011-C v2.0

4-40

Table 4.4.5.3-2. Maximum Output Power Backoff Allowances 1

Test Mode Configuration Output Power Reduction

R-PICH + R-DCCH 2.5 dB

R-PICH + R-DCCH + R-FCH (1500 bps) 2 dB

R-PICH + R-FCH (9600 bps) + R-SCH0 (9600 bps)

2 dB

R-PICH + R-DCCH + R-SCH0 (9600 bps) 1.5 dB

2

4.4.6 Minimum Controlled Output Power 3


The minimum controlled output power of the mobile station is the output power, measured 5

at the mobile station antenna connector, when both closed loop and open loop power 6

control indicate minimum output. 7





2. For each band class that the mobile station supports, configure the base station 12

and mobile station to operate in that band class and perform steps 3 through 7. 13




through 7. 17


set up a call using Fundamental Channel Test Mode 7 or Control Channel Test 19





24

3GPP2 C.S0011-C v2.0

4-41

Table 4.4.6.2-1. Test Parameters for Minimum Controlled Output Power 1



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

2


With both closed loop and open loop power control set to minimum, the mean output 4

power of the mobile station shall be less than -50 dBm/1.23 MHz for Spreading Rate 1 or -5

50 dBm/3.69 MHz for Spreading Rate 3 centered at the CDMA Channel frequency. 6

4.4.7 Standby Output Power and Gated Output Power 7


The standby output power is the mobile station output power when its transmit functions 9

are disabled (e.g., during the Mobile Station Initialization State, Mobile Station Idle State and 10

during the System Access State when the mobile station does not transmit access probes). 11

When operating in the variable data rate transmission mode in Radio Configurations 1 and 12

2, or when operating with the Reverse Pilot Channel gating or Reverse Fundamental 13

Channel gating enabled, the mobile station transmits at nominal controlled power level 14

only during gated-on periods, each defined as a power control group. The transmitted 15

power level is suppressed during gated-off periods. This test measures the time response of 16

the mean output power for a gated-on power control group (1.25 ms). 17








4. Measure the output power, at the mobile station antenna connector, during the 25

Mobile Station Initialization State or during the Mobile Station Idle State. 26

5. Send a page to the mobile station and measure the output power, at the mobile 27

station antenna connector, during the time periods between transmission of access 28

probes. 29

3GPP2 C.S0011-C v2.0

4-42

6. If the mobile station supports Radio Configuration 1 or 2, set up a call using 1


perform steps 11 and 12. 3





PILOT_GATING_USE_RATE = ‘1’ and PILOT_GATING_RATE = ‘01’ (1/2 rate) or ‘10’ 8

(1/4 rate). The base station shall not transmit on the Forward Dedicated Control 9

Channel to the mobile station under test during the test. Perform steps 11 through 10

15. 11





PILOT_GATING_USE_RATE = ‘1’ and PILOT_GATING_RATE = ‘01’ (1/2 rate) or ‘10’ 16

(1/4 rate). The base station shall not transmit on the Forward Dedicated Control 17

Channel to the mobile station under test during the test. Perform steps 11 through 18

15. 19


station supports Reverse Fundamental Channel gating, set up a call using 21

Fundamental Channel Test Mode 3 (see 1.3). Send an Extended Channel 22

Assignment Message with REV_FCH_GATING_MODE equal to ‘1’ (50% Reverse 23

Fundamental Channel transmission duty cycle). Send continuous 20 ms frames at 24

1500 bps data rate to the mobile station. Perform steps 11 through 15. 25


station supports Reverse Fundamental Channel gating, set up a call using 27

Fundamental Channel Test Mode 7 (see 1.3). Send an Extended Channel 28

Assignment Message with REV_FCH_GATING_MODE equal to ‘1’ (50% Reverse 29

Fundamental Channel transmission duty cycle). Send continuous 20 ms frames at 30

1500 bps data rate to the mobile station. Perform steps 11 through 15. 31

11. Send alternating ‘0’ and ‘1’ valid power control bits on the Forward Traffic Channel 32

or the Forward Power Control Subchannel. 33

12. Measure the time response of the mobile station output power, averaged over at 34

least 100 transitions to and 100 transitions from gated-on power control groups. 35

The power is measured at the mobile station antenna connector. 36

13. If gating is enabled, perform steps 14 and 15. 37

14. Send alternating ‘0’ and ‘1’ valid power control bits on the Forward Power Control 38

Subchannel. 39

15. Measure the ratio of the Reverse Fundamental Channel and the Reverse Pilot 40

Channel, averaged over at least 100 gated-on power control groups. The power is 41

measured at the mobile station antenna connector. 42

3GPP2 C.S0011-C v2.0

4-43

1

Table 4.4.7.2-1. Test Parameters for Standby Output Power and Gated Output Power 2



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

3


Standby Output Power: 5

When the transmitter is disabled, the output noise power spectral density of the mobile 6

station shall be less than -61 dBm, measured in a 1 MHz resolution bandwidth at the 7

mobile station antenna connector, for frequencies within the mobile station transmit band. 8

Gated Output Power: 9

Given an ensemble of power control groups, all with the same mean output power, the time 10

response of the ensemble average shall be within the limits shown in Figure 4.4.7.3-1. The 11

mean output power of the ensemble average is the mean value of gated-on output power 12

measured within a 1.25 ms time window. The measured width of response between points 13

3 dB below the mean output power shall be at least 1.25 × K − 0.003 ms and within the 14

range shown in Figure 4.4.7.3-1, where K is 1 for Radio Configurations 1, 2, or Reverse 15

Pilot Channel gating and 2 for Reverse Fundamental Channel gating. The output power 16

level outside of a 1.25 × K + 0.014 ms time window shall be at least 20 dB below the mean 17

output power of the ensemble average as shown in Figure 4.4.7.3-1. 18

The ratio of the Reverse Fundamental Channel and the Reverse Pilot Channel shall be 19

within 0.25 dB of –1.25 dB. 20

21

3GPP2 C.S0011-C v2.0

4-44

(1.25 × K - 0.003) ms

20 dB or tonoise floor

Time response of theensemble average

(average power control group)

Mean output power ofthe ensemble average

(reference line)

μs 7 μs 7

3 dB

1

Figure 4.4.7.3-1. Transmission Envelope Mask (Average Gated-on Power Control 2

Group) 3

4

4.4.8 Power Up Function Output Power 5

The tests in this section shall be performed if the mobile station supports the power up 6

function using Radio Configuration 1 or 2. 7


This test verifies the following power up function parameters: probe duration, initial power 9

offset, power increment between consecutive probes, time interval between consecutive 10

probes, the total number of PUF probes in one PUF attempt, and the maximum number of 11

full power PUF probes. 12







3. Set up a call using Fundamental Channel Test Mode 1 (see 1.3). 19

4. Send alternating ‘0’ and ‘1’ power control bits on the Forward Power Control 20

Subchannel. 21

5. Set the base station to ignore all PUF attempts. 22

3GPP2 C.S0011-C v2.0

4-45

6. Send a Power Up Function Message to the mobile station with the values specified 1

below: 2

3


PUF_SETUP_SIZE 0 (1 power control group)

PUF_PULSE_SIZE 15 (16 power control groups)

PUF_INTERVAL 2 (2 frames between start of subsequent PUF probes)

PUF_INIT_PWR 8 (8 dB)

PUF_PWR_STEP 1 (1 dB/step)

TOTAL_PUF_PROBES 3 (4 probes)

MAX_PWR_PUF 0 (1 pulse at max power)

PUF_FREQ_INCL 0 (same as current)

4

7. Measure the mobile station output power for each PUF probe at the antenna 5

connector. 6

8. Send a Power Up Function Message with the values specified below. Repeat step 7. 7

8


PUF_SETUP_SIZE 0 (1 power control group)

PUF_PULSE_SIZE 15 (16 power control groups)

PUF_INTERVAL 2 (2 frames between start of subsequent PUF probes)

PUF_INIT_PWR 16 (16 dB)

PUF_PWR_STEP 4 (4 dB/step)

TOTAL_PUF_PROBES 7 (8 probes)

MAX_PWR_PUF 2 (3 pulses at max power)

PUF_FREQ_INCL 0 (same as current)

9


In the first PUF probe attempt: 11

(a) The power increment between consecutive access probes in each PUF probe 12

attempt shall be 1 ± 0.33 dB. 13

3GPP2 C.S0011-C v2.0

4-46

(b) The duration of each PUF probe shall be between 20 ms and 22.5 ms, including 1

the setup time. 2

(c) There shall be two frames between the start of subsequent PUF probes. 3

(d) The number of PUF probes in the PUF probe attempt shall be four. 4

In the second PUF probe attempt: 5

(a) The power of the first PUF probe of each PUF probe attempt shall be 8 ± 2.67 dB 6

above the power of the PUF probes in the first PUF probe attempt. 7

(b) The power increment between consecutive PUF probes in each PUF probe attempt 8

shall be 4 ± 1.33 dB. 9

(c) The duration of each PUF probe shall be between 20 ms and 22.5 ms, including 10

the setup time. 11

(d) There shall be two frames between the start of subsequent PUF probes. 12

(e) The number of PUF probes in each PUF probe attempt shall be less than eight. 13

(f) The mobile station shall not transmit more than three PUF probes at full power. 14

4.4.9 Code Channel to Reverse Pilot Channel Output Power Accuracy 15


Code channel to Reverse Pilot Channel output power accuracy is the permissible error in 17

mobile station mean output power between each of the code channels and the Reverse Pilot 18

Channel during steady state operation. 19

The tests shall be performed for mobile stations that support the Reverse Pilot Channel. 20

Note that the test configuration parameters ensure that when testing a code channel other 21

than the Enhanced Access Channel or the Reverse Common Control Channel, then the 22

power of the tested code channel is not less than 1/30 of the total output power of the 23

mobile station. See 2.1.2.3.3.2 through 2.1.2.3.3.4 in [4]. 24


4.4.9.2.1 Code Channel Output Power for the Enhanced Access Channel Header, 26

Enhanced Access Channel Data, and Reverse Common Control Channel Data 27






3. Set the Reverse Link Attribute Adjustment Gain Table and Reverse Channel 33

Adjustment Gain Table maintained by the mobile station to 0. 34


3GPP2 C.S0011-C v2.0

4-47

1



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

2

5. Configure the base station so that the mobile station uses the Spreading Rate 1 or 3

Spreading Rate 3 Enhanced Access Channel. 4

6. Set the parameter values in the Enhanced Access Parameters Message to the values 5

specified below. 6

7


REACH_RATE_MODE 0 (9600 bps, 20 ms frame size)

REACH_MODE 0 (Basic Access Mode - no CACH or CPCCH)

EACH_PREAMBLE_NUM_FRAC 0 (no preamble)

EACH _PREAMBLE_ADD_DURATION 0 (no additional preamble)

EACH_MAX_RSP_SEQ 1 (1 sequence)

8


8. Monitor the mobile station transmitter output at the antenna connector with a 10

Code Domain Power Analyzer described in 6.4.2.2 during transmission of a probe 11

and measure the relative mean output power of the Enhanced Access Channel 12

Data to the Reverse Pilot Channel. 13

9. Configure the base station so that the mobile station monitors the Forward 14

Common Control Channel for Spreading Rate 1 (or Spreading Rate 3) and the 15

Common Assignment Channel. 16

10. Set the following values in the Enhanced Access Parameters Message: 17

18

3GPP2 C.S0011-C v2.0

4-48


RCCCH_RATE_MODE 0 (9600 bps, 20 ms frame size)

ACCESS_MODE 2 (Reservation Access Mode)

APPLICABLE_MODES 1 (Parameters are for Reservation Access Mode)

RA_PC_DELAY 4 (MS to ignore 4 PC bits after start of R-CCCH transmission)

RA_CPCCH_STEP_UP 1 (up step size is 0.5 dB)

RA_CPCCH_STEP_DN 1 (down step size is 0.5 dB)

CPCCH_RATE 2 (800 Hz power control rate)

NUM_PCSCH_RA 24 (24 Power Control Subchannels)

1

11. Send a Status Request Order on the Forward Common Control Channel. 2

12. Once the end of the header on the Enhanced Access Channel is detected at the 3

base station, send an Early Acknowledgement Channel Assignment Message on the 4

Common Assignment Channel addressed to the mobile station. 5

13. Send alternating ‘0’ and ‘1’ power control bits on the Common Power Control 6

Subchannel assigned to the mobile station. 7


Code Domain Power Analyzer described in 6.4.2.2 and measure the relative mean 9

output power of the Enhanced Access Channel Header and Reverse Common 10

Control Channel to the Reverse Pilot Channel. 11

4.4.9.2.2 Code Channel Output Power for the Reverse Traffic Channel 12








4. If the mobile station supports operation on the Reverse Fundamental Channel, set 20

up a call using Fundamental Channel Test Mode 3 (or 7) (see 1.3) with 9600 bps 21

data rate only, 20 ms frame length Radio Configuration 3 (or 7) Reverse 22

Fundamental Channel and perform steps 13 through 15. 23





3GPP2 C.S0011-C v2.0

4-49









8. If the mobile station supports operation on the Reverse Dedicated Control Channel, 9

set up a call using Dedicated Control Channel Test Mode 3 (or 7) (see 1.3) with 10

9600 bps data rate, 20 ms frame length Radio Configuration 3 (or 7) Reverse 11

Dedicated Control Channel and perform steps 13 through 15. 12

9. If the mobile station supports convolutional coding on the Reverse Supplemental 13

Channel, set up a call using Supplemental Channel Test Mode 3 (or 7) (see 1.3) 14

with 9600 bps data rate only, 20 ms frame length with convolutional coding of the 15

Radio Configuration 3 (or 7) Reverse Supplemental Channel and perform steps 13 16

through 15. 17

10. If the mobile station supports convolutional coding on the Reverse Supplemental 18

Channel, set up a call using Supplemental Channel Test Mode 3 (or 7) (see 1.3) 19

with both the highest data rate supported by the mobile station using a 20 ms 20

frame length with convolutional coding of the Radio Configuration 3 (or 7) Reverse 21

Supplemental Channel, and either a Radio Configuration 3 (or 7) 9600 bps, 20 ms 22

frame length Reverse Fundamental Channel or 9600 bps, 20 ms frame length 23

Reverse Dedicated Control Channel with 100% duty cycle and perform steps 13 24

through 15. 25

11. If the mobile station supports turbo coding on the Reverse Supplemental Channel, 26

set up a call using Supplemental Channel Test Mode 3 (or 7) (see 1.3) with 19200 27

bps data rate only, 20 ms frame length with turbo coding of the Radio 28

Configuration 3 (or 7) Reverse Supplemental Channel and perform steps 13 29

through 15. 30

12. If the mobile station supports operation on the Reverse Supplemental Channel 31

using turbo coding, set up a call using Supplemental Channel Test Mode 3 (or 7) 32

(see 1.3) with both the highest data rate supported by the mobile station using a 20 33

ms frame length with turbo coding of the Radio Configuration 3 (or 7) Reverse 34

Supplemental Channel, and either a Radio Configuration 3 (or 7) 9600 bps, 20 ms 35

frame length Reverse Fundamental Channel or 9600 bps, 20 ms frame length 36

Reverse Dedicated Control Channel with 100% duty cycle and perform steps 13 37

through 15. 38


40

3GPP2 C.S0011-C v2.0

4-50



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

1

14. Send alternating ‘0’ and ‘1’ power control bits on the Forward Traffic Channel. 2


Code Domain Power Analyzer described in 6.4.2.2 and measure the relative mean 4

output power of each active code channel to the Reverse Pilot Channel. 5

4.4.9.2.3 Code Channel Output Power for the Reverse Channel Quality Indicator Channel 6

and the Reverse Acknowledgement Channel 7




2. Configure the base station to use a single Forward Packet Data Control Channel. 11





5. Set up a call using Packet Data Channel Test Mode 10a (see 1.3). 16

6. Configure the mobile station to use differential reporting mode and repetition factor 17

two on the Reverse Channel Quality Indicator Channel (REV_CQICH_REPS = ’01’). 18

Configure the mobile station to use repetition factor four on the Reverse 19

Acknowledgment Channel (REV_ACKCH_REPS = ’10’). 20


22



orc

IE Pilot dB -7

orc

IE PDCCH dB -7.4

23

3GPP2 C.S0011-C v2.0

4-51

8. Configure the base station to transmit on the Forward Packet Data Control 1

Channel four slot length messages addressed to the mobile station with a duty 2

cycle equal to 100%. 3

9. Send alternating ‘0’ and ‘1’ bits on the Forward Power Control Subchannel. 4


Code Domain Power Analyzer described in 6.4.2.2 and measure the mean output 6

power of the Reverse Channel Quality Indicator Channel and the Reverse 7

Acknowledgment Channel relative to the Reverse Pilot Channel. For the Reverse 8

Channel Quality Indicator Channel, the 3200 bps (full C/I value) and the 800 bps 9

(differential C/I value) frames are recorded separately. 10


The mean output power difference between the Enhanced Access Channel Header and 12

Reverse Pilot Channel shall be 6.75 ± 0.25 dB. 13

The mean output power difference between either the Enhanced Access Channel Data or 14

Reverse Common Control Channel and the Reverse Pilot Channel shall be 3.75 ± 0.25 dB. 15

For tests not involving the Reverse Supplemental Channel, the mean output power 16

difference between each Reverse Traffic Channel code channel and the Reverse Pilot 17

Channel shall be the code channel accuracy specified in Table 4.4.9.3-1. 18

For tests involving the Reverse Supplemental Channel, the mean output power difference 19

between the Reverse Supplemental Channel code channel and the Reverse Pilot Channel 20

shall be the code accuracy specified in Table 4.4.9.3-2 and 4.4.9.3-3 for the convolutional 21

coded and turbo coded cases, respectively. For the Reverse Fundamental Channel (or 22

Reverse Dedicated Control Channel, whichever is the configuration) being transmitted in 23

addition to the Supplemental Channel, the mean output power difference between the 24

Reverse Fundamental Channel (or Reverse Dedicated Control Channel) code channel and 25

the Reverse Pilot Channel shall be the code accuracy specified in Table 4.4.9.3-4 and 26

4.4.9.3-5 for the convolutional coded and turbo coded cases, respectively. 27

The mean output power difference between the Reverse Channel Quality Indicator Channel 28

and the Reverse Pilot Channel shall be 2 ± 0.25 dB when the Reverse Channel Quality 29

Indicator Channel is operating at 3200 bps (transmitting a full C/I value) and it shall be -7 30

± 0.25 dB when the Reverse Channel Quality Indicator Channel is operating at 800 bps 31

(transmitting a differential C/I value). 32

The mean output power difference between the Reverse Acknowledgement Channel and the 33

Reverse Pilot Channel shall be 0 ± 0.25 dB. 34

35

3GPP2 C.S0011-C v2.0

4-52

Table 4.4.9.3-1. Code Channel Accuracy Requirements for the Reverse Fundamental 1

Channel and Reverse Dedicated Control Channel 2

Data Rate (bps)

Code Channel Accuracy (dB)

1500 -5.88 ± 0.25

2700 -2.75 ± 0.25

4800 -0.25 ± 0.25

9600 3.75 ± 0.25

3

Table 4.4.9.3-2. Code Channel Accuracy Requirements for the (Convolutional Coded) 4

Reverse Supplemental Channel 5

Data Rate (bps)


9600 3.75 ± 0.25

19200 6.25 ± 0.25

38400 7.5 ± 0.25

76800 9 ± 0.25

153600 10.5 ± 0.25

307200 12 ± 0.25

614400 14 ± 0.25

6

Table 4.4.9.3-3. Code Channel Accuracy Requirements for the (Turbo Coded) Reverse 7

Supplemental Channel 8

Data Rate (bps)


19200 5.5 ± 0.25

38400 7 ± 0.25

76800 8.5 ± 0.25

153600 9.5 ± 0.25

307200 11 ± 0.25

614400 14 ± 0.25

1036800 15.63 ± 0.25

9

3GPP2 C.S0011-C v2.0

4-53



Transmitted in Addition to the (Convolutional Coded) Reverse Supplemental Channel 3

R-SCH Data Rate (bps)

R-FCH (or R-DCCH) Code Channel Accuracy (dB)

9600 3.75 ± 0.25

19200 3.63 ± 0.25

38400 2.38 ± 0.25

76800 1.13 ± 0.25

153600 -0.75 ± 0.25

307200 -3 ± 0.35

614400 -4.75 ± 0.6

4



Transmitted in Addition to the (Turbo Coded) Reverse Supplemental Channel 7

R-SCH Data Rate (bps)

R-FCH (or R-DCCH) Code Channel Accuracy (dB)

19200 3.5 ± 0.25

38400 2.5 ± 0.25

76800 1.375 ± 0.25

153600 -0.375 ± 0.25

307200 -2.5 ± 0.25

614400 -3.5 ± 0.35

1036800 -6 ± 0.6

8

4.4.10 Reverse Pilot Channel Transmit Phase Discontinuity 9


This test measures the mobile station Reverse Pilot Channel phase over the total range of 11

mobile station output power levels. 12

The tests shall be performed for mobile stations that support the Reverse Pilot Channel. 13

3GPP2 C.S0011-C v2.0

4-54


1. Connect the base station to the mobile station antenna connector as shown in Figure 2

6.5.1-4. The AWGN generator and the interference generator are not applicable in this 3

test. 4

2. Set the power control step size to 1 dB. 5

3. For each band class that the mobile station supports, configure the base station and 6

mobile station to operate in that band class and perform steps 4 through 13. 7

4. If the mobile station supports operation on the Reverse Fundamental Channel, set up a 8

call using Fundamental Channel Test Mode 3 (see 1.3) with 9600 bps data rate only 9

Radio Configuration 3 Reverse Fundamental Channel. Otherwise, set up a call using 10

Dedicated Control Channel Test Mode 3 (see 1.3) with 9600 bps data rate Radio 11

Configuration 3 Reverse Dedicated Control Channel with 100% duty cycle. Perform 12


5. If the mobile station supports operation on the Reverse Fundamental Channel, set up a 14

call using Fundamental Channel Test Mode 7 (see 1.3) with 9600 bps data rate only 15

Radio Configuration 5 Reverse Fundamental Channel. Otherwise, set up a call using 16

Dedicated Control Channel Test Mode 7 (see 1.3) with 9600 bps data rate Radio 17

Configuration 5 Reverse Dedicated Control Channel with 100% duty cycle. Perform 18


6. Set the attenuation in the Forward CDMA Channel to yield a Reverse CDMA Channel 20

output power level, measured at the mobile station antenna connector, of -50 dBm and 21












output power level, measured at the mobile station antenna connector, of + 10 dBm 33

and perform steps 11 through 13. 34

11. Measure the Reverse Pilot Channel phase at the mobile station antenna connector 35

while transmitting an arbitrary number of alternating ‘0’ and ‘1’ valid power control bits 36

(the last bit is a ‘1’ bit), followed by ten contiguous 37

3GPP2 C.S0011-C v2.0

4-55

‘00011000110001110101010101010101’ valid power control bit sequences12, and 1

followed by ten contiguous ‘11100111001110000101010101010101’ valid power 2

control bit sequences. Ensure that the mobile station output power level changes 3

within the requirements of this document for each closed loop power control command 4

sent to the mobile station. 5



(the last bit is a ‘1’ bit), followed by ten contiguous 8

‘00000000011111110101010101010101’ valid power control bit sequences, and 9

followed by ten contiguous ‘11111111100000000101010101010101’ valid power 10

control bit sequences. Ensure that the mobile station output power level changes 11

within the requirements of this document for each closed loop power control command 12

sent to the mobile station. 13



(the last bit is a ‘1’ bit), followed by sixteen consecutive ‘0’ valid power control bits, and 16

followed by sixteen consecutive ‘1’ valid power control bits. Ensure that the mobile 17

station output power level changes within the requirements of this document for each 18

closed loop power control command sent to the mobile station. 19


For all tests, the mobile station shall meet the following requirements on transmitted 21

Reverse Pilot Channel phase: 22

a) not to exceed more than one ‘type one’ phase discontinuity in any 5 ms period over the 23

full range of mobile station output power, and 24

b) not to exceed more than one ‘type two’ phase discontinuity in any 20 ms period over the 25

full range of mobile station output power, 26

where a ‘type one’ phase discontinuity is defined as a phase change of greater than 56 27

degrees in less than 0.5 ms, and a ‘type two’ phase discontinuity is a phase change of 28

greater than 90 degrees in less than 1 ms. 29

4.4.11 Reverse Traffic Channel Output Power During Changes in Data Rate 30


This test verifies the time response of the Reverse Traffic Channel output power at data rate 32

transition boundaries. 33

This test shall be performed for mobile stations that support the Reverse Supplemental 34

Channel. 35

12 The last sixteen power control bits of each sequence, i.e. ‘0101010101010101’, are included to assist with phase transient test equipment pilot tracking loop reacquisition.

3GPP2 C.S0011-C v2.0

4-56



Figure 6.5.1-4. The AWGN generator and interference generator are not applicable 3

in this test. 4





4. If the mobile station supports the Radio Configuration 3 Reverse Supplemental 9

Channel, set up a call using either Fundamental Channel Test Mode 3 or 10

Dedicated Control Channel Test Mode 3 with 9600 bps data rate only (see 1.3) and 11


5. If the mobile station supports the Radio Configuration 5 Reverse Supplemental 13

Channel, set up a call using either Fundamental Channel Test Mode 7 or 14

Dedicated Control Channel Test Mode 7 with 9600 bps data rate only (see 1.3) and 15



18



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4 (SR 1)

-12.4 (SR 3)

19

7. Configure the base station to direct the mobile station to periodically start and stop 20

transmission using the lowest supported data rate on the Reverse Supplemental 21

Channel and perform steps 9 and 10. 22

8. Configure the base station to direct the mobile station to periodically start and stop 23

transmission using the highest supported data rate on the Reverse Supplemental 24

Channel and perform steps 9 and 10. 25

9. Send alternating ‘0’ and ‘1’ power control bits on the Forward Traffic Channel. 26

10. Measure the mobile station output power at the data rate transition frame 27

boundary for at least 100 transitions in data rate. 28


The mean output power of the mobile station shall be within ±0.5 dB of its final value 30

within 200 μs of the data rate transition frame boundary. 31

3GPP2 C.S0011-C v2.0

4-57

4.5 Limitations on Emissions 1

4.5.1 Conducted Spurious Emissions 2


Conducted spurious emissions are emissions at frequencies that are outside the assigned 4

CDMA Channel, measured at the mobile station antenna connector. This test measures the 5

spurious emissions during continuous transmission. 6



Figure 6.5.1-4. The AWGN and interference generators are not applicable in this 9

test. Connect a spectrum analyzer (or other suitable test equipment) to the mobile 10

station antenna connector. 11

2. For each band class and radio configuration that the mobile station supports, 12

configure the base station and mobile station to operate in that band class and 13


3. If the mobile station supports Reverse Traffic Channel Radio Configuration 1 and 15

Forward Traffic Channel Radio Configuration 1, set up a call using Fundamental 16













demodulation of Radio Configuration 3, 4, or 5, set up a call using Fundamental 29








Supplemental Channel 0 data rate, and perform steps 17 through 26 or steps 27 37




3GPP2 C.S0011-C v2.0

4-58















demodulation of Radio Configuration 6, 7, 8, or 9, set up a call using Fundamental 15








Supplemental Channel 0 data rate, and perform steps 17 through 26 (Test 10). 23









16. Measure the spurious emission levels. 32




station. 36


not active, increase Îor by 1 dB. Repeat this step until the desired channel 38



3GPP2 C.S0011-C v2.0

4-59






channel configuration is no longer active. 6

24. Set Îor to the value at which the highest mobile station output power was achieved 7

with the desired channel configuration active. Verify the desired channel 8

configuration is active. 9




28. Set the base station to use normal power control using the smallest supported 13

closed loop power control step size supported by the mobile station. 14


not the active channel configuration, decrease the power control set point at the 16

base station in 1 dB steps until the desired channel configuration is the active 17

channel configuration. The power control set point is the desired mobile station 18

output power level set at the base station simulator. 19


31. Increase the power control set point at the base station by 0.5 dB. 21





channel configuration is no longer active. 26

34. Set the power control set point at the base station to the value at which the highest 27

mobile station output power was achieved with the desired channel configuration 28

active. Verify that the desired channel configuration is active. 29



32

33

3GPP2 C.S0011-C v2.0

4-60

Table 4.5.1.2-1. Test Parameters for Testing Spurious Emissions with a Single Traffic 1

Code Channel at Maximum RF Output Power 2



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

3

Table 4.5.1.2-2. Test Parameters for Testing Spurious Emissions with Multiple Traffic 4

Code Channels at Maximum RF Output Power 5


orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

6

3GPP2 C.S0011-C v2.0

4-61

Table 4.5.1.2-3. Îor Values for Testing Spurious Emissions with Multiple Traffic Code 1

Channels at Maximum RF Output Power 2

Îor (dBm/1.23 MHz) Band Class Mobile Station

Class Test 4 Test 5 Test 6

Class I -95.4 -93.4 -93.9

0, 3, 9 and 12 Class II -91.4 -89.4 -89.9

Class III -87.4 -85.4 -85.9

Class I -95.4 -93.4 -93.9

Class II -90.4 -88.4 -88.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

1, 4, 8, 14 and 15

Class V -75.4 -73.4 -73.9

Class I -95.4 -93.4 -93.9

Class II -90.4 -88.4 -88.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

6 (outside Japan)

Class V -75.4 -73.4 -73.9

Class I and II -84.4 -82.4 -82.9

Class III -85.4 -83.4 -83.9

Class IV -80.4 -78.4 -78.9

6 (in Japan)

Class V -75.4 -73.4 -73.9

Class II -95.4 -93.4 -93.9

2 Class III -91.4 -89.4 -89.9

Class IV -87.4 -85.4 -85.9

Class I -97.4 -95.4 -95.9

Class II -92.4 -90.4 -90.9

Class III -87.4 -85.4 -85.9

5 and 11

Class IV -82.4 -80.4 -80.9

7 and 10 Class I -91.4 -89.4 -89.9

Class II -87.4 -85.4 -85.9

3

Deleted: and

3GPP2 C.S0011-C v2.0

4-62


Depending on local radio regulations, the mobile station shall meet ITU Category A or B 2

emissions rules as appropriate. For Band Class 5, 6, 8, 9, 11 and 12, a mobile station shall 3

meet ITU Category B emission rules. 4

The spurious emissions in the mobile station’s receive band shall be less than -76 dBm 5

measured in a 1 MHz resolution bandwidth for Band Classes 0, 1, 2, 4, 5, 6, 7, 8, 9, 10, 6

11, 12, 14 and 15. For band class 3, the spurious emissions in the mobile station’s receive 7

band shall be less than -81 dBm measured in a 1 MHz resolution bandwidth. 8

4.5.1.3.1 Spreading Rate 1 9

When transmitting in Band Class 0, 2, 5, 7, 9, 10, 11 or 12 with Spreading Rate 1, the 10

mean spurious emissions with ten or more averages shall be less than all limits specified in 11

Table 4.5.1.3.1-1. 12

13

Table 4.5.1.3.1-1. Band Groups 450 and 800 Transmitter Spurious Emission Limits 14

for Spreading Rate 1 15

For |Δf| Within the Range Emission Limit

885 kHz to 1.98 MHz Less stringent of -42 dBc/30 kHz or -54 dBm/1.23 MHz

1.25 to 4.00 MHz

(Band Class 10 only)

-13 dBm/30 kHz

1.98 MHz to 4.00 MHz Less stringent of -54 dBc/30 kHz or -54 dBm/1.23 MHz

> 1.98 MHz (Band Class 3 only)

-54 dBc/30 kHz

2.25 MHz to 4.00 MHz (Band Class 7 only)

-35 dBm/6.25 kHz

> 4.00 MHz (ITU Category A only)

-13 dBm / 1 kHz; -13 dBm / 10 kHz; -13 dBm/100 kHz; -13 dBm / 1 MHz;

9 kHz < f < 150 kHz 150 kHz < f < 30 MHz 30 MHz < f < 1 GHz 1 GHz < f < 5 GHz

> 4.00 MHz (ITU Category B only)


9 kHz < f < 150 kHz 150 kHz < f < 30 MHz 30 MHz < f < 1 GHz

1 GHz < f < 12.75 GHz

Note: All frequencies in the measurement bandwidth shall satisfy the 16

restrictions on |Δf| where Δf = center frequency - closer measurement edge 17

frequency (f). Compliance with the -35 dBm / 6.25 kHz limit is based on the 18

use of measurement instrumentation such that the reading taken with any 19

resolution bandwidth setting should be adjusted to indicate spectral power in 20

Deleted: b

Deleted: c

Deleted: and

Deleted: 3,

Deleted: Band Class 0, 2, 3, 5, 7, 9, 10, 11 and 12

3GPP2 C.S0011-C v2.0

4-63

a 6.25 kHz segment. ITU Category B is intended to apply to only Band Class 5, 1

9, 11 and 12. The -13 dBm/30 kHz requirement for Band Class 10 is based on 2

CFR 47 Part 90.691(a)(2). 3

4

When transmitting in Band Class 1, 4, 6 or 8 with Spreading Rate 1, the spurious 5

emissions shall be less than all limits specified in Table 4.5.1.3.1-2. 6

7

Table 4.5.1.3.1-2. Band Group 1900 Transmitter Spurious Emission Limits 8



1.25 MHz to 1.98 MHz less stringent of -42 dBc/30 kHz or -54 dBm/1.23 MHz

1.98 MHz to 4.00 MHz less stringent of -50 dBc/30 kHz or -54 dBm/1.23 MHz

2.25 MHz to 4.00 MHz (Band Class 6 only)

-[13 + 1 × (Δf – 2.25 MHz)] dBm / 1 MHz

> 4.00 MHz (ITU Category A)



> 4.00 MHz (ITU Category B)



1 GHz < f < 12.75 GHz



frequency (f). ITU Category B is intended to apply to only Band Class 6 and 12

8. 13

14

When transmitting in Band Class 3, mean spurious emissions with ten or more averages 15

shall be less than the limits specified in Table 4.5.1.3.1-3. 16

17

Table 4.5.1.3.1-3. Band Class 3 Transmitter Spurious Emission Limits for Spreading 18

Rate 1 19

20

Deleted: For Band Class 3, the lower and upper limits of the frequency measurement are currently 10 MHz and 3 GHz in Japan radio measurement documents.

Deleted: Band Class 1, 4, 6 and 8

Deleted: also

Deleted: Additional Band Class 3 Transmitter Spurious Emission Limits

Deleted: Measurement Frequency ... [1]

3GPP2 C.S0011-C v2.0

4-64

Measurement Frequency

For |Δf| Within the

Range Emission Limit

≥ 900kHz and

< 1.98MHz -42 dBc / 30 kHz > 815 MHz and

≤ 850 MHz, > 887 MHz and

≤ 889 MHz, > 893 MHz and

≤ 901 MHz, > 915 MHz and

≤ 925 MHz

≥ 1.98 MHz 25 μW (-16 dBm) / 100 kHz; Pout ≤ 30 dBm

-54 dBc / 100 kHz; Pout > 30 dBm

< 1.98 MHz 25 μW (-16 dBm) / 30 kHz; Pout ≤ 30 dBm

Less stringent of -60 dBc / 30 kHz or 2.5 μW (-26 dBm) / 30 kHz; Pout > 30 dBm

> 885 MHz and ≤ 958 MHz,

except > 887 MHz and

≤ 889 MHz, > 893 MHz and

≤ 901 MHz, > 915 MHz and

≤ 925 MHz

≥ 1.98 MHz 25 μW (-16 dBm) / 100 kHz; Pout ≤ 30 dBm


< 1.98 MHz 25 μW (-16 dBm) / 30 kHz; Pout ≤ 30 dBm


≤ 885 MHz and

> 958 MHz, except

815-850MHz ≥ 1.98 MHz 25 μW (-16 dBm) / 1 MHz; Pout ≤ 44 dBm

More stringent of -60 dBc / 1 MHz and 20 mW (13 dBm) / 1 MHz; Pout > 44 dBm

Note: All frequencies in the measurement bandwidth shall satisfy the restrictions on |Δf| where Δf = center frequency - closer measurement edge frequency (f). The lower and upper

limits of the frequency measurement are currently 10 MHz and 3 GHz in Japan radio measurement documents.

1

When transmitting in Band Class 6 with Spreading Rate 1, the mean spurious emissions 2

with ten or more averages shall also be less than the requirements in Table 4.5.1.3.1-4. 3

4

3GPP2 C.S0011-C v2.0

4-65




Emission Limit Victim Band

1884.5 to 1919.6 MHz -41 dBm / 300 kHz PHS

925 to 935 MHz -67 dBm / 100 kHz GSM 900

935 to 960 MHz -79 dBm / 100 kHz GSM 900

1805 to 1880 MHz -71 dBm / 100 kHz DCS 1800

Note: Measurements apply only when the measurement frequency is 3

at least 5.625 MHz from the CDMA center frequency. The non-PHS 4

band measurements are made on frequencies which are integer 5

multiples of 200 kHz. As exceptions, up to five measurements with a 6

level up to the spurious emission limits in Table 4.5.1.3.1-2 are 7

allowed. 8

9

When transmitting in Band Class 11 or 12 with Spreading Rate 1, the mean spurious 10

emissions with ten or more averages shall also be less than the requirements in Table 11

4.5.1.3.1-5. 12

13

Table 4.5.1.3.1-5. Additional Band Class 11 and 12 Transmitter Spurious Emission 14

Limits for Spreading Rate 1 15

For |Δf| Within the Range

Emission Limit

885 kHz to 1.125 MHz

-47 – 7 × (|Δf| – 885) / 240 dBc in 30 kHz

1.125 MHz to 1.98 MHz

-54 – 13 × (|Δf| – 1125) / 855 dBc in 30 kHz

1.98 MHz to 4.00 MHz

-67 – 15 × (|Δf| – 1980) / 2020 dBc in 30 kHz

4.00 MHz to 10.0 MHz

-51 dBm in 100 kHz

Note: All frequencies in the measurement bandwidth shall satisfy the restrictions on |Δf| 16

where Δf = center frequency - closer measurement edge frequency (f). Δf is positive offset 17

from the highest valid CDMA channel in the band subclass or negative offset from the 18

lowest valid CDMA channel in the band subclass. The emission limits for Band Class 11 19

and 12 (European PAMR bands) are designed to allow co-existence with incumbent services 20

in Europe and are tighter than ITU Category B requirements. 21


Deleted: 1893.5

3GPP2 C.S0011-C v2.0

4-66

4.5.1.3.2 Spreading Rate 3 1

When transmitting with Spreading Rate 3, the mean spurious emissions with ten or more 2

averages shall be less than the limits specified in Table 4.5.1.3.2-1. 3

4

Table 4.5.1.3.2-1. Transmitter Spurious Emission Limits for Spreading Rate 3 5


2.5 MHz to 2.7 MHz -14 dBm / 30 kHz

2.7 MHz to 3.5 MHz -[14 + 15 × (Δf – 2.7 MHz)] dBm / 30 kHz

3.08 MHz (Band Class 6 only) -33 dBc / 3.84 MHz

3.5 MHz to 7.5 MHz -[13 + 1 × (Δf – 3.5 MHz)] dBm / 1 MHz

7.5 MHz to 8.5 MHz -[17 + 10 × (Δf – 7.5 MHz)] dBm / 1 MHz

8.08 MHz (Band Class 6 only) -43 dBc / 3.84 MHz

8.5 MHz to 12.5 MHz -27 dBm / 1 MHz

> 12.5 MHz (ITU Category A) -13 dBm / 1 kHz; -13 dBm / 10 kHz; -13 dBm/100 kHz; -13 dBm / 1 MHz;


> 12.5 MHz (ITU Category B)



1 GHz < f < 12.75 GHz



frequency (f). The requirements at offsets of 3.08 and 8.08 MHz are equivalent 8

to ACLR requirements of 33 and 43 dB from a Spreading Rate 3 mobile station 9

transmitter into a Spreading Rate 3 or IMT-DS mobile station receiver offset by 10

5 and 10 MHz respectively. ITU Category B is intended to apply to only Band 11

Class 5, 6, 8, 9, 11 and 12. 12

13

A Band Class 6 mobile station with Spreading Rate 3 shall also meet the requirements in 14

Table 4.5.1.3.2-2. 15

16

3GPP2 C.S0011-C v2.0

4-67




Emission Limit Victim Band

1884.5 to 1919.6 MHz -41 dBm / 300 kHz PHS

925 to 935 MHz -67 dBm / 100 kHz GSM 900

935 to 960 MHz -79 dBm / 100 kHz GSM 900

1805 to 1880 MHz -71 dBm / 100 kHz DCS 1800

Note: Measurements apply only when the measurement frequency is 3

at least 12.5 MHz from the CDMA center frequency. The non-PHS 4

band measurements are made on frequencies which are integer 5

multiples of 200 kHz. As exceptions, up to five measurements with a 6

level up to the spurious emission limits in Table 4.5.1.3.2-1 are 7

allowed. 8

9


4.5.2 Radiated Spurious Emissions 11

Current region-specific radio regulation rules shall apply. 12

For example, a Band Class 7 mobile station operating under US regional requirements 13

shall limit mean radiated spurious emissions with ten or more averages to less than –70 14

dBW/MHz EIRP in the GPS L1 band from 1559 to 1610 MHz. 15

4.5.3 Occupied Bandwidth 16

This test is applicable to Band Class 3 and 6 mobile stations only. 17


The occupied bandwidth is defined as the frequency range, whereby the power of emissions 19

averaged over the frequency above and under the edge frequency are 0.5% each of the total 20

radiation power of a modulated carrier. 21




applicable in this test. Connect a spectrum analyzer to the mobile station antenna 25

connector. 26




and 5. 30

Deleted: 1893.5

3GPP2 C.S0011-C v2.0

4-68

3. If the mobile station supports Band Class 6 and demodulation of Radio 1

Configuration 6, 7, 8, or 9, set up a call using Fundamental Channel Test Mode 7 2

or Control Channel Test Mode 7 (see 1.3) with 9600 bps data rate only and perform 3

steps 4 and 5. 4



6. Set the resolution bandwidth of the spectrum analyzer to 30 kHz. The value of the 7

occupied bandwidth is calculated by an external or internal computer by summing 8

all samples stored as “total power”. 9

10

Table 4.5.3.2-1. Test Parameters for Testing Occupied Bandwidth at Maximum RF 11

Output Power 12



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

13


The occupied bandwidth shall not exceed 1.48 MHz for Spreading Rate 1 and 4.6 MHz for 15

Spreading Rate 3 (Band Class 6 only). 16

3GPP2 C.S0011-C v2.0

4-69

No text1

3GPP2 C.S0011-C v2.0

5-1

5 CDMA ENVIRONMENTAL REQUIREMENTS 1

5.1 Temperature and Power Supply Voltage 2

5.1.1 Definition 3

The temperature and voltage ranges denote the ranges of ambient temperature and power 4

supply input voltages over which the mobile station will operate and meet the requirements 5

of these standards. The ambient temperature is the average temperature of the air 6

surrounding the mobile station. The power supply voltage is the voltage applied at the 7

input terminals of the mobile station. The manufacturer shall specify the temperature 8

range and the power supply voltage over which the equipment is to operate. In order to 9

provide a convenient means for the manufacturer to express the temperature range under 10

which the mobile station conforms to these recommended minimum standards, 11

temperature ranges designated by letters are defined in Table 5.1.1-1. 12

13

Table 5.1.1-1. Temperature Ranges 14

Designator Range

A -40°C to +70°C

B -30°C to +60°C

C -20°C to +50°C

D 0°C to +45°C

15


The mobile station shall be installed in its normal configuration (i.e., in its normal 17

mounting arrangement fully assembled) and placed in a temperature chamber. The 18

temperature chamber shall be stabilized at the manufacturer's highest specified operating 19

temperature, and the mobile station shall be operated over the power supply input voltage 20

range13 specified by the manufacturer or ±10% if the range is not specified. With the 21

mobile station operating, the temperature shall be maintained at the specified test 22

temperature without forced circulation of air from the temperature chamber being directly 23

applied to the mobile station. The measurements specified in 5.1.3 shall then be 24

performed. 25

Turn the mobile station off, stabilize the mobile station in the chamber at room 26

temperature, and repeat the measurements specified in 5.1.3. 27

13 In general, the voltage range will be the useful operating range of the battery used in the mobile station.

3GPP2 C.S0011-C v2.0

5-2

Turn the mobile station off, stabilize the mobile station in the chamber at the coldest 1

operating temperature specified by the manufacturer, and repeat the measurements 2

specified in 5.1.3. 3

The overall temperature range may be reduced to a lesser range than -30°C to +60°C if the 4

manufacturer uses circuitry that automatically inhibits RF transmission when the 5

temperature falls outside the lesser range specified. Measurements shall be made at the 6

specified extremes of the manufacturer’s temperature range. The manufacturer shall verify 7

that RF transmission is inhibited outside of the specified temperature range. 8


The mobile station equipment shall meet all of the minimum standards specified in 10

Sections 3 and 4 under the standard environmental test conditions specified in 6.2 for all 11

supported band classes. Over the ambient temperature and power supply ranges specified 12

by the manufacturer, the operation of the mobile station equipment shall meet the 13

following minimum standards for all supported band classes unless noted otherwise: 14

1. Receiver sensitivity and dynamic range as specified in 3.5.1.3. The received CDMA 15

power, Îor, used to measure receiver sensitivity may be increased 2 dB at 60°C and 16

higher. 17

2. Frequency accuracy as specified in 4.1.3. 18

3. Waveform quality as specified in 4.3.4.3. 19

4. Range of estimated open loop output power as specified in 4.4.1.3. For 20

temperatures outside of the range +15°C to +35°C, the test tolerance lower limit 21

may be relaxed to -12.5 dB. 22

5. Range of closed loop correction as specified in 4.4.4.3. 23

6. Maximum RF output power as specified in 4.4.5.3. For Temperature Range 24

Designators A and B, the ERP for a Band Group 450 or 800 mobile station may 25

drop by 2 dB at 60°C and higher. For Temperature Range Designators A and B, the 26

EIRP for a Band Group 1900 Class II through V mobile station may drop by 2 dB 27

at 60°C and higher. These temperature range backoff allowances are in addition to 28

the test mode configuration backoff allowances specified in 4.4.5.3-2. These 29

requirements do not apply other than for coldest, room and highest operating 30

temperature test points. 31

7. Minimum controlled output power as specified in 4.4.6.3. 32

9. Conducted spurious emissions as specified in 4.5.1.3. 33

5.2 High Humidity 34

5.2.1 Definition 35

The term “high humidity” denotes the relative humidity at which the mobile station will 36

operate with the specified performance. 37

Deleted: band classes 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: band classes 1, 4, 6 and 8

3GPP2 C.S0011-C v2.0

5-3


The mobile station, after having operated normally under standard test conditions, shall be 2

placed, inoperative, in a humidity chamber with the humidity maintained at 0.024/gm 3

H2O/gm Dry Air at 50°C (40% Relative Humidity) for a period of not less than eight hours. 4

The measurements specified in 3.5.1 (receiver sensitivity and dynamic range) and 4.3.2 5

(waveform quality) shall then be performed. No readjustment of the mobile station shall be 6

allowed during this test. 7

Turn the mobile station off, stabilize the mobile station in the chamber at standard 8

conditions within six hours, and perform the measurements specified in Sections 3 and 4 9

of this Standard. 10


The mobile station equipment shall meet the minimum standards specified in 3.5.1.3 and 12

4.3.2.3 under the high humidity conditions. Once stabilized in standard conditions, the 13

mobile station shall meet all the minimum standards specified in Sections 3 and 4 of this 14

Standard. 15

5.3 Vibration Stability 16

5.3.1 Definition 17

Vibration stability is the ability of the mobile station to maintain specified mechanical and 18

electrical performance after being vibrated. 19


Sinusoidal vibration at 1.5 g acceleration swept through the range of 5 to 500 Hz at the 21

rate of 0.1 octave/second shall be applied to the mobile station in three mutually 22

perpendicular directions (sequentially) for a single sweep rising in frequency followed by a 23

single sweep falling in frequency. 24


The mobile station equipment shall meet all the minimum standards specified in Sections 3 26

and 4 after being subjected to the above vibration tests. 27

5.4 Shock Stability 28

5.4.1 Definition 29

Shock stability is the ability of the mobile station to maintain specified mechanical and 30

electrical performance after being shocked. 31


The mobile station shall be subjected to three test table impacts, in three mutually 33

perpendicular directions and their negatives, for a total of 18 impacts. In all cases, the 34

mobile station shall be secured to the test table by its normal mounting hardware. Each 35

3GPP2 C.S0011-C v2.0

5-4

impact shall be a half sine wave, lasting from 7 to 11 ms, with at least 20 g peak 1

acceleration. 2


The mobile station equipment shall meet all the minimum standards specified in Sections 3 4

and 4 of this Standard and shall not suffer any mechanical damage after being subjected to 5

the above shock tests. 6

7

3GPP2 C.S0011-C v2.0

6-1

6 CDMA STANDARD TEST CONDITIONS 1

6.1 Standard Equipment 2

6.1.1 Basic Equipment 3

The equipment shall be assembled, and any necessary adjustments shall be made in 4

accordance with the manufacturer's instructions for the mode of operation required. When 5

alternative modes are available, the equipment shall be assembled and adjusted in 6

accordance with the relevant instructions. A complete series of measurements shall be 7

made for each mode of operation. 8

6.1.2 Associated Equipment 9

The mobile station equipment may include associated equipment during tests, provided 10

that the associated equipment is normally used in the operation of the equipment under 11

test. For mobile station equipment, this may include power supplies, handsets, cradles, 12

charging stands, control cables, and battery cables. 13

6.2 Standard Environmental Test Conditions 14

Measurements under standard atmospheric conditions shall be carried out under any 15

combination of the following conditions: 16

• Temperature: +15°C to +35°C 17

• Relative humidity: 45% to 75% 18

• Air pressure: 86,000 Pa to 106,000 Pa (860 mbar to 1060 mbar) 19

If desired, the results of the measurements can be corrected by calculation to the standard 20

reference temperature of 25°C and the standard reference air pressure of 101,300 Pa 21

(1013 mbar). 22

6.3 Standard Conditions for the Primary Power Supply 23

6.3.1 General 24

The standard test voltages shall be those specified by the manufacturer, or an equivalent 25

type that duplicates the voltage, impedance, and ampere hours (if relevant for the 26

measurement) of the recommended supply. 27

6.3.2 Standard DC Test Voltage from Accumulator Batteries 28

The standard (or nominal) DC test voltage specified by the manufacturer shall be equal to 29

the standard test voltage of the type of accumulator to be used, multiplied by the number 30

of cells minus an average DC power cable loss value that the manufacturer determines as 31

being typical (or applicable) for a given installation. Since accumulator batteries may or 32

may not be under charge or may be in a state of discharge when the equipment is being 33

operated, the manufacturer shall also test the equipment at anticipated voltage extremes 34

above and below the standard voltage. The test voltages shall not deviate from the stated 35

3GPP2 C.S0011-C v2.0

6-2

values by more than ±2% during a series of measurements carried out as part of a single 1

test on the same equipment. 2

6.3.3 Standard AC Voltage and Frequency 3

For equipment that operates from the AC mains, the standard AC test voltage shall be 4

equal to the nominal voltage specified by the manufacturer. If the equipment is provided 5

with different input taps, the one designated “nominal” shall be used. The standard test 6

frequency and the test voltage shall not deviate from their nominal values by more than 7

±2%. 8

The equipment shall operate without degradation with input voltage variations of up to 9

±10%, and shall maintain its specified transmitter frequency stability for input voltage 10

variations of up to ±15%. The frequency range over which the equipment is to operate shall 11

be specified by the manufacturer. 12

6.4 Standard Test Equipment 13

6.4.1 Standard Channel Simulator 14

6.4.1.1 Channel Model Parameters 15

The channel simulator shall support the following channel model parameters: 16

• All paths are independently faded. 17

• The fading is Rayleigh. The probability distribution function of power, F(P), of the 18

signal power level P is: 19

⎪⎭

⎪⎬⎫

⎪⎩

⎪⎨⎧

≤>−=

−

0 P 0, 0P,e1)P(F

aveP/P, 20

where Pave is the mean power level. 21

• The level crossing rate, L(P) is: 22

⎪⎭

⎪⎬⎫

⎪⎩

⎪⎨⎧

≤

>⋅⋅π=

−

0P 0,

0P,efP/P2)P(LaveP/P

dave , 23

where fd is the Doppler frequency offset associated with the simulated vehicle speed 24

given by 25

cd fcvf ⎟

⎠⎞

⎜⎝⎛= , 26

where fc is the carrier frequency, v is the vehicle speed, and c is the speed of light in 27

a vacuum. 28

3GPP2 C.S0011-C v2.0

6-3

• The power spectral density, S(f), is: 1

⎪⎪

⎭

⎪⎪

⎬

⎫

⎪⎪

⎩

⎪⎪

⎨

⎧ +≤≤−

⎟⎟⎠

⎞⎜⎜⎝

⎛ −−=

otherwise 0,

,

1

1

)(2

dcdc

dc

fffff

ffffS 2

• The autocorrelation coefficient of the unwrapped phase14, ρ(t), is: 3

( )[ ] ( )[ ] ( )[ ]∑∞

=

−− π

π−

⎭⎬⎫

⎩⎨⎧ π

π+π

π=ρ

1n2

n2d0

2

2

d01

d01

n

tf2J

43tf2Jsin

216tf2Jsin

23)t( , 4

where J0( ) is a zero-order Bessel function of the first kind. 5

This autocorrelation coefficient is shown in Figure 6.4.1-1. 6

-0.2

0.0

0.2

0.4

0.6

0.8

1.0

1.2

0 0.5 1 1.5 2 2.5 3

Lag t in units of 1 / Doppler Frequency

ρ(t)

7

Figure 6.4.1-1. Autocorrelation Coefficient of the Phase 8

14 The term “unwrapped” refers to the continuous nature of the phase, that is, with no discontinuities of 2π.

3GPP2 C.S0011-C v2.0

6-4

6.4.1.2 Channel Model Parameter Conditions and Tolerances 1

The following standard conditions and tolerances on the channel model parameters shall 2

be supported by the channel simulator: 3

• Vehicle speed, v: 3 km/h for Band Classes 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 14 4

and 15. 5


and 15. 7

• Vehicle speed, v: 14 km/h for Band Classes 1, 4, 6 and 8. 8


and 15. 10

• Vehicle speed, v: 100 km/h for Band Classes 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 11

14 and 15. 12

• Power distribution function, F(P): 13

1. The tolerance15 shall be within ±1 dB of calculated, for power levels from 10 dB 14

above to 20 dB below the mean power level. 15

2. The tolerance shall be within ±5 dB of calculated, for power levels from 20 dB 16

below to 30 dB below the mean power level. 17

• Level crossing rate, L(P): 18

The tolerance16 shall be within ±10% of calculated, for power levels from 3 dB 19

above to 30 dB below the mean power level. 20

• Measured power spectral density, S(f), around the carrier, fc: 21

1. At frequency offsets |f - fc| = fd, the maximum power spectral density S(f) shall 22

exceed S(fc) by at least 6 dB. 23

2. For frequency offsets |f - fc| > 2fd, the maximum power spectral density S(f) 24

shall be less than S(fc) by at least 30 dB. 25

• Simulated Doppler frequency, fd, shall be computed from the measured S(f) as 26

( )2/12

cd

df)f(S

dffS)ff(2f

⎥⎥⎥

⎦

⎤

⎢⎢⎢

⎣

⎡ −=

∫∫ 27

• Measured autocorrelation function of the unwrapped phase, ρ(t): 28

15 The tolerance is defined as the error in power expressed in dB, i.e. 10×log10(actual/calculated).

16 The tolerance is defined as the error in level crossing rate expressed as the ratio between actual and calculated values.

Deleted: b

Deleted: c

Deleted: and

Deleted: b

Deleted: c

Deleted: and

Deleted: b

Deleted: c

Deleted: b

Deleted: c

Deleted: and

Deleted: b

Deleted: c

Deleted: and

3GPP2 C.S0011-C v2.0

6-5

1. At a lag of 0.05/fd, ρ(t) shall be 0.8 ± 0.1. 1

2. At a lag of 0.15/fd, ρ(t) shall be 0.5 ± 0.1. 2

6.4.1.3 Channel Simulator Configurations 3

The standard channel simulator shall support all the configurations specified in Table 4

6.4.1.3-1. 5

6

Table 6.4.1.3-1. Standard Channel Simulator Configurations 7

8

For transmit diversity tests, all base station transmit antennas shall be passed through 9

independent but identically configured channel simulators. See Figure 6.5.1-5 for 10

applicable test setup. 11

6.4.2 Waveform Quality Measurement Equipment 12

6.4.2.1 Rho Meter for Radio Configuration 1 and 2 13

When operating in Radio Configuration 1 and 2, the mobile station transmitter generates 14

O-QPSK signals as described in Section 2.1.3.1 of [4]. 15

The ideal, complex, transmitter signal is given as 16

tj 0e)t(R)t(s ω= , 17

where R(t) is the complex envelope of the transmitter signal and ω0 is the radian carrier 18

frequency. 19

The samples of R(t) at t = kTs are given as 20

Channel Simulator Configuration

Parameters 1 2 3 4 5 6

Vehicle Speed [km/h]

Band Groups 450 and 800

8 30 30 100 0 3

Band Group 1900 8 14 30 100 0 3

Number of Paths 2 2 1 3 2 1

Path 2 Power (Relative to Path 1) [dB] 0 0 N/A 0 0 N/A

Path 3 Power (Relative to Path 1) [dB] N/A N/A N/A -3 N/A N/A

Delay from Path 1 to Input [μs] 0 0 0 0 0 0

Delay from Path 2 to Input [μs] 2 2 N/A 2 2 N/A

Delay from Path 3 to Input [μs] N/A N/A N/A 14.5 N/A N/A

3GPP2 C.S0011-C v2.0

6-6

( ) ( ) ( ) ( ) ( )∑ ∑ φ−−+φ−=n n

nccsncss sin2/TnTkTgjcosnTkTgkTR , 1

where g(kTs) is the unit impulse response of the baseband filter described in Section 2

2.1.3.1.13 of [4]. Tc is the duration of a PN chip, and φn is the phase corresponding to the 3

nth chip, occurring at time tn = nTc , as specified in [4]. The chip rate, 1/Tc , is 1.2288 4

Mcps. The sample rate 1/Ts equals 4/Tc . 5

Modulation accuracy is the ability of the transmitter to generate the ideal signal, s(t). 6

The actual, complex, transmitter waveform is given as 7

( ) ( )[ ] ( )( )τ+ωΔ+ω+τ+= tj0 0etE)t(RCtx , 8

where τ is the time offset of the actual transmit signal referenced to the time coordinate of 9

R(t); 0j00 eAC θ= is a complex constant representing the magnitude of the transmitter 10

signal, A0, and arbitrary phase, θ0; Δω is the radian frequency offset of the actual carrier 11

relative to the frequency of the ideal carrier; and E(t) is the complex envelope of the error of 12

the actual transmitter signal with respect to the ideal transmitted signal. 13

The time and frequency offset of the actual transmitter signal is corrected by multiplying by 14

a complex factor to produce 15

( ) ( ) ( )[ ]tˆ j 0e ˆtxty ωΔ+ωτ−= , 16

in which τ and ωΔˆ are estimates, to the accuracy specified below, of the transmit time 17

offset and the frequency offset of the actual transmitter signal. The radian frequency offset, 18

ωΔˆ , is converted to frequency offset in Hertz by πωΔ=Δ 2/ˆf . 19

The parameters τ , Δ ˆ ω and θ 0 shall be determined such that the sum-square-error 20

between the reference signal and the signal-under-test is minimized. 21

The ρ-meter shall contain a band-limiting filter. This filter should have less than ±0.1 dB 22

ripple in the passband, and a minimum corner frequency (0.1 dB) of 700 kHz. At 23

frequencies greater than 1.2 MHz, the filter shall have at least 40 dB rejection. The 24

implementation of this filter shall be determined by the ρ-meter manufacturer, consistent 25

with the accuracy requirements specified below. 26

Z(t) denotes the actual output of the filter. 27

Modulation accuracy is measured by determining the fraction of power at the filter output, 28

Z(t), that correlates with the ideal waveform, R(t), sampled at the ideal decision points tk = 29

2(k-1)Ts = (k-1)Tc/2. Modulation accuracy is given in terms of the transmitter waveform 30

quality factor, ρ, defined as 31

3GPP2 C.S0011-C v2.0

6-7

∑ ∑

∑

= =

==ρ M

1k

M

1k

2k

2k

2M

1k

*kk

ZR

ZR

, 1

where Zk = Z(tk) is the kth sample of the compensated transmit signal in the measurement 2

interval; Rk = R(tk) is the kth sample of the ideal signal in the measurement interval; and M 3

is the measurement interval in half-chips comprising at least 500 μs for Spreading Rate 1 4

and 167 μs for Spreading Rate 3. 5

The value of Δ ˆ ω found in minimizing the mean-squared-error for E(t) is the carrier 6

frequency error in radians-Hz. 7

The value of τ found in minimizing the mean-squared-error for E(t) is the transmit time 8

error in μs. 9

The accuracy of the waveform quality measurement equipment shall be as follows: 10

Waveform quality factor (ρ): ± 0.003 over the range of 0.90 to 1.00. 11

Frequency offset: ± 30 Hz. 12

Transmit time offset: ± 135 ns. 13

The equipment shall be tunable over the applicable bands and be operational over the 14

amplitude range of -50 to +40 dBm. External attenuators and/or amplifiers may be used to 15

meet these power requirements and may be considered as part of the equipment. 16

6.4.2.2 Rho Meter for Radio Configuration 3 through 9 17

When operating in Radio Configuration 3 through 9, the mobile station transmitter 18

generates HPSK signals as described in Section 2.1.3.1 of [4]. 19

6.4.2.2.1 The Ideal Composite Reference Signal 20

A code-channel is established by the Walsh function for that channel, denoted as [ ]kWNm . 21

This represents a Walsh function of length N that is serially constructed from the mth row 22

of a N × N Hadamard matrix. For additional details of the recursive procedure for 23

constructing Walsh functions from Hadamard matrices, see 2.1.3.1.8.1 of [4]. 24

The reference signal for the ( )thN,m code-channel is written as17 25

17 The convention is to use round brackets, ( ), for continuous time and square brackets, [ ], for discrete time. The function ⎣ ⎦x is equal to the largest integer less than or equal to x, and the function

k mod N is equal to the remainder when k is divided by N. { }xRe denotes the real part of x, and

{ }xIm denotes the imaginary part of x.

3GPP2 C.S0011-C v2.0

6-8

⎣ ⎦[ ] [ ]NmodkWN/kd]k[R Nm

Nm

Nm = 1

where the integer k corresponds to time; t = kTc, where Tc is the chip interval. [ ]ndNm is the 2

complex data symbol, where [ ]{ }ndRe Nm and [ ]{ }ndIm N

m take on values ± 1, or null (when 3

[ ]ndNm is either purely real or purely imaginary). 4

The ideal, composite, reference signal is given as 5

[ ] [ ]{ } [ ]{ }[ ]∑ β+α=N,m

Nm

Nm

Nm

Nm kRImjkRRekR 6

where the summation is over the values of m,N corresponding to the active code-channels. 7

Nmα and N

mβ correspond to the relative magnitudes of the signals sent to the I and Q-8

channels of the modulator, respectively, for the (m,N)th code-channel. Either Nmα or N

mβ 9

may equal zero, when only the I or Q component of the (m,N)th code-channel is used, and 10

Nmα = N

mβ , when a balanced QPSK signal is transmitted on the code-channel. The range of 11

the time variable, k, extends over a multiple of Nmax, where Nmax is the maximum length of 12

the Walsh functions, and starts and stops at the beginning and end of maximal length 13

Walsh intervals. 14

6.4.2.2.2 The Transmitter Signal-Under-Test 15

The complex envelope, R[k], is scrambled by a complex, pseudo-noise, sequence, P[k], to 16

produce the complex envelope of the ideal, spread-spectrum, signal given as 17

W[k] = P[k] R[k] 18

The ideal transmitter signal is obtained by passing W[k] through a transmitter filter 19

followed by a digital-to-analog converter, reconstruction filter, and upconverter. The filtered 20

and reconstructed baseband signal is written as 21

( ) [ ] ( )ck

kTthkWtS −=∑ 22

where h(t) is the unit-impulse response of a filter for which h[k], specified in Table 23

2.1.3.1.13.1-1 of [4] for Spreading Rate 1 and Table 2.1.3.1.13.2-1 of [4] for Spreading Rate 24

3, is impulse-invariant with values h(k Tc/4) = h(k). 25

The complex transmitter signal-under-test is given as18 26

( ) ( )[ ] ( )( )[ ]0c tff2j0 e)t(EtStx θ+τ+Δ+πτ++τ+= 27

18 The actual transmitter signal is the real-part of x(t).

3GPP2 C.S0011-C v2.0

6-9

where cf is the nominal carrier frequency, fΔ is the carrier frequency error, 0θ is the 1

arbitrary carrier phase, τ is the time-offset of the signal-under-test relative to the ideal 2

signal, and ( )tEo is the complex envelope of the error (deviation from ideal) of the 3

transmitter signal-under-test. x(t) is time aligned with the reference signal, and 4

compensated in frequency and phase, by introducing a time correction and a complex 5

multiplicative factor to produce 6

( ) ( ) ( )[ ]θ+Δ+π−τ−=ˆtff2j ceˆtxty 7

The parameters θΔτ ˆand,f,ˆ shall be determined such that the sum-square-error between 8

the reference signal and the signal-under-test is minimized. 9

y(t) shall be passed through a complementary filter to remove the interchip interference 10

(ICI) introduced by the transmitter filter. The impulse response of the filter resulting from 11

cascading the complementary filter with the ideal transmitter filter shall satisfy Nyquist’s 12

criterion for zero ICI approximated by filter null levels at least 50 dB below the on-time 13

response at the appropriate sample times. The complementary filter will determine the 14

bandwidth of the measurement equipment, and shall have a noise bandwidth not greater 15

than cT2

1 . 16

6.4.2.2.3 Active Code-Channel Identification, Symbol Detection and Parameter Estimation 17

In the identification of active channels, symbol detection, and in the measurement of 18

modulation accuracy described below, it is implied that synchronization is performed so 19

that the time record of the baseband signal-under-test is coincident with the ideal reference 20

signal. 21

The identification of active code-channels provides the set of m,N necessary for generating 22

the composite reference signal. Active code-channels can be identified by employing a test 23

signal or by measuring the code-domain power (CDP), to be defined below, of the signal-24

under-test and identifying channels as active if their CDP is above a predetermined 25

threshold. It is suggested that a test signal be specified to reduce the degree of uncertainty 26

in the measurement. 27

Detection of the symbols, [ ]ndNm , is necessary for generating a reference signal. The 28

symbols can be detected using a conventional detection procedure. The probability of 29

symbol detection error shall be negligibly small. 30

For the measurement of modulation quality (ρ and CDP defined below), the parameters 0Λ , 31

Nmα , N

mβ , τ , fΔ , and θ shall be determined such as to minimize the sum-square-difference 32

between the signal at the output of the complementary filter, [ ]kV , and the spread-33

spectrum signal, [ ]kW , given as 34

[ ] [ ]∑ −Λ−=εk

20

2 kWˆkV 35

3GPP2 C.S0011-C v2.0

6-10

where the range of k is over a multiple of maxN as defined above. 0Λ is a complex number 1

representing the I/Q origin-offset of [ ]kV given as 2

[ ] [ ][ ]∑ −=ΛkN

0 kWkVNL

1ˆ 3

where maxNN NLNL max= , in which maxNL is the number of maximal length Walsh intervals 4

of length maxN in the measurement interval (range of k). 5

0Λ shall be estimated jointly with the other parameters, Nmα , N

mβ , τ , fΔ and 0θ to improve 6

the accuracy in the estimates of these other parameters; however, 0Λ shall not be removed 7

from [ ]kV when calculating modulation accuracy. 0Λ will be an output of the measuring 8

equipment, reported in dB relative to the RMS value of the reference signal. 9

6.4.2.2.4 Rho (ρ) 10

Modulation accuracy is measured by determining the fraction of power at the filter output, 11

Z(t), that correlates with the ideal waveform, R(t), sampled at the ideal decision points tk = 12

(k-1)Tc, when the transmitter is modulated only by the Pilot Channel (the 0th code channel). 13

Modulation accuracy is given in terms of the transmitter waveform quality factor, ρ, defined 14

as 15

∑ ∑

∑

= =

==ρM

1k

M

1k

2k

2k,0

2M

1k

*kk,0

ZR

ZR

16

where Zk = Z(tk) is the kth sample of the compensated transmit signal in the measurement 17

interval; R0,k = R0(tk) is the kth sample of the ideal pilot-only signal in the measurement 18

interval; and M is the measurement interval in chips comprising at least 500 μs for 19

Spreading Rate 1 and 167 μs for Spreading Rate 3. 20

The value of fΔ found in minimizing the mean-squared-error for ( )tEo is the carrier 21

frequency error in Hertz. 22

The value of τ found in minimizing the mean-squared-error for ( )tEo is the transmit time 23

error in microseconds. The accuracy of the waveform quality measurement equipment shall 24

be as follows: 25

Waveform quality factor (ρ): ± 0.003 over the range of 0.90 to 1.00. 26

Frequency offset: ± 30 Hz. 27

Transmit time offset: ± 135 ns. 28

3GPP2 C.S0011-C v2.0

6-11

The equipment shall be tunable over the applicable bands and be operational over the 1

amplitude range of -50 to +40 dBm. External attenuators and/or amplifiers may be used to 2

meet these power requirements and may be considered as part of the equipment. 3

6.4.2.2.5 Code-domain Power (CDP) 4

CDP can be computed for any of the signals, such as [ ]kR or [ ]kZ considered above, or for 5

the error signal E[k] = Z[k] – R[k]. 6

CDP gives the distribution of signal energy among the code-channels, normalized by the 7

total signal energy. Since CDP is a measure of relative energy levels, it is also a measure of 8

relative average power levels over the measurement interval. The energy of the projection of 9

the real and imaginary parts of [ ]kZ on Walsh function [ ]kWNm are19 10

[ ]{ } [ ]∑ ∑−

=

−

= ⎥⎥⎦

⎤

⎢⎢⎣

⎡+

1L

0n

21N

0k

Nm

NkWnNkZRe

N1 11

and 12

[ ]{ } [ ]∑ ∑−

=

−

= ⎥⎥⎦

⎤

⎢⎢⎣

⎡+

1L

0n

21N

0k

Nm

NkWnNkZIm

N1 , 13

respectively, and the total energy of [ ]kZ is 14

[ ]∑−

=

1NL

0k

2N

kZ 15

where NL is the number of Walsh intervals of length N in the measurement interval. 16

The ratio of these energy terms are the components of the CDP of [ ]kZ on the ( )thN,m 17

channel given as 18

[ ]{ } [ ]

[ ]∑

∑ ∑−

=

−

=

−

= ⎥⎥⎦

⎤

⎢⎢⎣

⎡+

=ρ 1NL

0k

2

1L

0n

21N

0k

Nm

NRm

N

N

kZN

kWnNkZRe

; m=0, 1, …, N-1 19

20

19 At this point, the time axis is labeled so that k = 0 corresponds to the first chip sample in the measurement interval.

3GPP2 C.S0011-C v2.0

6-12

and 1

[ ]{ } [ ]

[ ]∑

∑ ∑−

=

−

=

−

= ⎥⎥⎦

⎤

⎢⎢⎣

⎡+

=ρ 1NL

0k

2

1L

0n

21N

0k

Nm

NIm N

N

kZN

kWnNkZIm

; m=0, 1, …, N-1 2

The total CDP of Z[k] on the (m,N)th channel is 3

NIm

NRm

Nm ρ+ρ=ρ 4

6.4.2.2.6 Power in Undesired Channels 5

Rho is a global, quantitative, measure of modulation quality; however, it does not provide a 6

measure of how error power is distributed among code-channels. A measure of the code-7

domain distribution of error power is provided by the CDP of the error signal. This gives 8

rise to the concept of a peak code-domain error limit, where the relative power in the error 9

must not exceed a certain value in any of the inactive code channels. Inactive code 10

channels include only those Walsh functions that are inactive on both the I and Q carrier 11

phase components. 12

As an example, suppose that the modulation quality (Rho) is 0.97. Then the power ratio, 13

implicit in this value, is –15.23 dB. If it is further assumed that the error and reference 14

signals are uncorrelated, then the total relative power in the error is 15

03.0|1N

0mError

Nm =ρ∑

−

=

16

Assuming this error power were distributed uniformly across the code-domain (at N = 16, 17

with real and imaginary parts), then the fractional error power projected on each phase 18

component of each code channel would be 0.0009375, corresponding to an error floor of –19

30.3 dB relative to the total signal power level. In practice, there is no reason to believe that 20

error power will be spread uniformly. 21

6.4.2.2.7 Code Domain Time Offsets and Phase Offsets Relative to Reverse Pilot Channel 22

The reference signal, [ ]kRNm , for the (m, N)th code channel given in 6.4.2.2.1, is resampled 23

in time and shifted in phase to produce 24

[ ] ( )Nmc

Nm

jNm kTRekR

~~ Nm τ+= θ 25

[ ]kRNm is replaced by [ ]kR

~~Nm in the expression for the composite reference signal in 26

6.4.2.2.1. [ ]kR~~N

m is used in place of [ ]kRNm only for measuring time and phase offsets. 27

3GPP2 C.S0011-C v2.0

6-13

The parameters Nmτ and N

mθ are determined by finding the values of Nmτ and N

mθ that 1

minimize the sum-square difference between the signal-under-test and the composite 2

reference signal as described in 6.4.2.2.3. The time and phase offset parameters are 3

estimated jointly with the other parameters as described in 6.4.2.2.3. 4

The time and phase offsets are given as 5

N0

Nm

Nm ˆˆ τ−τ=τΔ 6

and 7

N0

Nm

Nm ˆˆ θ−θ=θΔ 8

where N0τ and N

0θ are the time and phase offset parameters , respectively, of the reverse 9

pilot channel. 10

6.4.2.3 Code Domain Measurement Equipment Accuracy 11

The accuracy of the code domain measurement equipment shall be as shown in Table 12

6.4.2.3-1. 13

14

Table 6.4.2.3-1. Accuracy of Code Domain Measurement Equipment 15

Parameter Symbol Accuracy Requirement

Code domain power coefficients ρi ±5×10-4 from 5×10-4 to 1.0

Frequency Error (exclusive of test equipment time base errors)

Δf ±10 Hz

Code domain time offset relative to Reverse Pilot Channel

Δτi ±2 ns

Code domain phase offset relative to Reverse Pilot Channel

Δθi ±0.01 radians

Code domain power offset relative to Reverse Pilot Channel

ΔPi ±0.05 dB

16

6.4.3 Base Station Equipment 17

6.4.3.1 Transmitter Equipment 18

The base station transmitter shall be capable of generating the following channels at the 19

specified output power (relative to the total power): 20

• Forward Pilot Channel: -5 to -10 dB or off. 21

• Forward Transmit Diversity Pilot Channel: -5 to -19 dB or off. 22

3GPP2 C.S0011-C v2.0

6-14

• Sync Channel: -7 to -20 dB or off. 1

• Quick Paging Channel: -3 to -15 dB or off. 2

• Paging Channel: -7 to -20 dB or off. 3

• Broadcast Control Channel: -7 to -30 dB or off. 4

• Forward Common Control Channel: -7 to -20 dB or off. 5

• Common Power Control Channel: -7 to -20 dB or off. 6

• Forward Common Assignment Channel: -7 to -20 dB or off. 7

• Forward Packet Data Control Channel: -7 to -21 dB or off. 8

• Forward Dedicated Control Channel: -7 to -20 dB or off. 9

• Forward Fundamental Channel: -7 to -20 dB or off for full rate power output. Lower 10

rates will reduce the Forward Fundamental Channel power so as to maintain a 11

constant energy per bit. 12

• Forward Power Control Subchannel: This subchannel is always transmitted at the 13

same power as the full rate speech bits, except when a common power control 14

subchannel of the Common Power Control Channel is assigned, without a Forward 15

Fundamental Channel or a Forward Dedicated Control Channel. 16

• Forward Supplemental Channel: -7 to -20 dB or off. 17

• Forward Packet Data Control Channel: -7 to -20 dB or off. 18

• Forward Packet Data Channel: -1 to -14 dB for 3.0912 Mbps rate operation. Lower 19

rates will reduce the Forward Packet Data Channel power as appropriate. 20

• OCNS: 0 to -30 dB or off. The OCNS may, as an option, be composed of Paging, 21

Sync, or Traffic Channels operating on different Walsh channels than the channel(s) 22

being used for test. For transmit diversity tests, the OCNS power shall be allocated 23

equally between the non-transmit diversity and transmit diversity antennas. 24

In addition, the base station transmitter shall meet the following requirements: 25

• Frequency range: base station frequencies as specified in [4]. 26

• Frequency accuracy: ±0.2 ppm 27

• Frequency resolution: 10 Hz 28

• Output range: 0 to -110 dBm/1.23 MHz 29

• Amplitude resolution: 0.1 dB for all channels 30

• Output accuracy: 31

1.Relative amplitude: ±0.25 dB (Step ≤ 1 dB) 32

2. Relative levels between any two channels: ±0.1 dB 33

(External calibration may be required for this.) 34

• Absolute output accuracy: ±2.0 dB 35

3GPP2 C.S0011-C v2.0

6-15

• Minimum waveform quality factor (ρ): greater than 0.966 (excess power is less than 1

0.15 dB) 2

• Source VSWR: 2.0:1 3

• ACLR (Band Class 6): 74 dB for Spreading Rate 1 and 66 dB for Spreading Rate 3 4

Forward Power Control 5

• The base station shall have means to enable or disable Forward Power Control. 6

• The base station shall have means to select the power control format, with Forward 7

Power Control mode (FPC_MODE) choices equal to: 8

• ‘000’ (800 bps primary) 9

• ‘001’ (400 bps primary, 400 bps secondary) 10

• ‘010’ (200 bps primary, 600 bps secondary) 11

• When enabled, Forward Power Control shall adjust the power of the Forward 12

Fundamental Channel, the Forward Supplemental Channel, and the Forward Dedicated 13

Control Channel if they are enabled. 14

• The reverse link delay shall be 1/2 power control group or less between the end of the 15

power control group with an active power control bit and the corresponding change in 16

the base station power for the Forward Traffic Channel under test. 17

• When Forward Power Control is enabled, the OCNS power shall be adjusted to maintain 18

nearly constant base station power. The OCNS power adjustments should be made 19

such that the base station power varies by no more than ±0.5 dB and shall be made 20

such that the base station power varies by no more than ±1.0 dB. 21

The OCNS adjustments should be made in the same power control group as the 22

response to Power Control Bits and shall occur no more than two power control groups 23

later than the response to Power Control Bits. 24

6.4.3.2 Receiver Equipment 25

Input Range -50 to +40 dBm. External attenuators and/or amplifiers may be used to meet 26

these power requirements and may be considered as part of the equipment. 27

Reporting capability of time of arrival with a resolution of 1/8 chip or shorter in duration. 28

6.4.3.3 Protocol Support 29

The base station shall be capable of supplying the protocols required by this document. 30

6.4.3.4 Timing Signals 31

The base station shall provide the following system timing signals referenced to the base 32

station antenna port for use as triggers by other measurement equipment: 33

• 20 ms frame clock. 34

• 26.67 ms clock: Short sequence rollover. 35

3GPP2 C.S0011-C v2.0

6-16

• 80 ms clock: Alignment of frame clock and zero PN offset 26.67 ms clock. 1

• Even second time mark. 2

• 1.25 ms power control group clock. 3

Signals synchronized to the following events: 4

• Insertion of bad frames (or frames deleted). 5

• Start of power control bit sequences. 6

6.4.4 AWGN Generator 7

The AWGN generator shall meet the following minimum performance requirements: 8

• Minimum bandwidth: 1.8 MHz for Spreading Rate 1 or 5.4 MHz for Spreading Rate 3 9

• Frequency ranges20: 10

11

Band Class Frequency Range (MHz)

0 864 to 899

1 1925 to 1995

2 912 to 965

3 827 to 875

4 1835 to 1875

5 416 to 499

6 2105 to 2175

7 741 to 769

8 1800 to 1885

9 920 to 965

10 846 to 945

11 457 to 471

12 910 to 926

12

• Frequency resolution: 1 kHz. 13

• Output accuracy: ±2 dB for outputs greater than or equal to -80 dBm/1.23 MHz. 14

• Amplitude resolution: 0.1 dB. 15

20 The frequency ranges are based on covering the receive band and frequencies as great as 5 MHz outside the band.

3GPP2 C.S0011-C v2.0

6-17

• Output range: -20 to -95 dBm/1.23 MHz. 1

• The AWGN generator shall be uncorrelated to the ideal transmitter signal. See 2

6.4.3.1. 3

6.4.5 CW Generator 4

The CW generator shall meet the following minimum performance requirements: 5

• Output frequency range: Tunable over applicable range of radio frequencies. 6

• Frequency accuracy: ±1 ppm. 7

• Frequency resolution: 100 Hz. 8

• Output range: -50 dBm to -10 dBm, and off. 9

• Output accuracy: ±1.0 dB for above output range and frequencies. 10

• Amplitude resolution: 0.1 dB. 11

• Output phase noise: As required. 12

• Output Phase Noise at –20 dBm Power: 13

-144 dBc/Hz at a frequency of 1 GHz as measured at a 285 kHz offset for Band 14

Groups 450 and 800. 15

-144 dBc/Hz at a frequency of 2 GHz as measured at a 635 kHz offset for Band 16

Groups 1900. 17

6.4.6 Spectrum Analyzer 18

The spectrum analyzer shall provide the following functionality: 19

• General purpose frequency domain measurements. 20

• Integrated channel power measurements (power spectral density in 1.23 MHz). 21

The spectrum analyzer shall meet the following minimum performance requirements: 22

• Frequency range: Tunable over the applicable radio frequency range. 23

• Frequency resolution: 1 kHz. 24

• Frequency accuracy: ±0.2 ppm. 25

• Displayed dynamic range: 70 dB. 26

• Display log scale fidelity: ±1 dB over the above displayed dynamic range. 27

• Amplitude measurement range for signals from 10 MHz to either 2.6 GHz for Band 28

Classes 0, 2, 3, 5, 7, 9, 10, 11 and 12, 6 GHz for Band Classes 1, 4, 8, 14 and 15 or 29

12.75 GHz for Band Class 6: 30

1. Power measured in 30 kHz resolution bandwidth: -90 to +20 dBm. 31

2. Integrated 1.23 MHz channel power: -70 to +40 dBm. 32

3. Noise floor: -140 dBm/Hz. 33

Deleted: (band classes 0, 2, 3, 5, 7, 9, 10, 11 and 12)

Deleted: (band classes 1, 4, 6 and 8)

Deleted: b

Deleted: c

Deleted: b

Deleted: c

Deleted: and

3GPP2 C.S0011-C v2.0

6-18

4. External attenuation may be used to meet the high power end of the range and 1

may be considered as part of the equipment. 2

• Absolute amplitude accuracy in the CDMA transmit and receive bands (for integrated 3

channel power measurements): 4

1. ±1 dB over the range of -40 dBm to +20 dBm. 5

2. ±1.3 dB over the range of -70 dBm to +20 dBm. 6

• Relative flatness: ±1.5 dB over frequency range 10 MHz to either 2.6 GHz for Band 7

Classes 0, 2, 3, 5, 7, 9, 10, 11 and 12, 6 GHz for Band Classes 1, 4, 8, 14 and 15 or 8

12.75 GHz for Band Class 6. 9

• Resolution bandwidth filter: Synchronously tuned or Gaussian (at least 3 poles) with 10

3 dB bandwidth selections of 1 MHz, 300 kHz, 100 kHz, and 30 kHz. 11

• Post detection video filters: Selectable in decade steps from 100 Hz to at least 1 MHz. 12

• Detection modes: Average detection mode. 13

• RF input impedance: Nominal 50 ohms. 14

The spectrum analyzer may also provide the functionality of time domain (zero span) 15

measurements with true average power determination. If this functionality is provided, the 16

spectrum analyzer shall meet the following additional minimum performance requirements: 17

• Time domain sweep time: Selectable from 50 μs to 100 ms. 18

• Delayed sweep trigger: Selectable from 5 μs to 40 ms. 19

• External sweep trigger. 20

• Sufficient bandwidths to make the time domain measurements. 21

6.4.7 Average Power Meter 22

The power meter shall provide the following functionality: 23

• Average power measurements. 24

• True RMS detection for both sinusoidal and non-sinusoidal signals. 25

• Absolute power in linear (watt) and logarithmic (dBm) units. 26

• Relative (offset) power in dB and percentage units. 27

• Automatic calibration and zeroing. 28

• Averaging of multiple readings. 29

The power meter shall meet the following minimum performance requirements: 30

• Frequency range: 10 MHz to either 1 GHz for Band Classes 0, 2, 3, 5, 7, 9, 10, 11 31

and 12, 2 GHz for Band Classes 1, 4 and 8, or 12.75 GHz for Band Class 6. 32

• Power range: -70 dBm (100 pW) to + 40 dBm (10 W). 33

Deleted: band classes


Deleted: and



3GPP2 C.S0011-C v2.0

6-19

Different sensors may be required to optimally provide this power range. External 1

attenuation may be used to meet the high power end of the range and may be 2

considered as part of the equipment. 3

• Absolute and relative power accuracy: ±0.2 dB (5%, in Watts). 4

Excludes sensor and source mismatch (VSWR) errors, zeroing errors (significant at 5

bottom end of sensor range), and power linearity errors (significant at top end of 6

sensor range). 7

• Power measurement resolution: Selectable between 0.1 or 0.01 dB. 8

• Sensor VSWR: 1.15:1. 9

6.4.8 Phase Transient Measuring Equipment 10

The phase tracking equipment shall be capable of measuring the phase of the mobile 11

station transmission under the follow conditions: 12

• The power may be between –50 dBm and +30 dBm. 13

• The power transient for this measurement may be as large as 24 dB. 14

• The accuracy of the phase transient measuring equipment shall be better than 0.1 15

radians for a transient of 20 ms. 16

6.5 Functional System Set-ups 17

6.5.1 Functional Block Diagrams 18

Figures 6.5.1-1 through 6.5.1-5 show the functional block diagrams of the set-up for 19

different tests: 20

21

Base Station Mobile StationUnder Test

Tx

Rx

AWGNGenerator

Rx/Tx

ChannelSimulator

Ioc

Ior IoIor^Σ

22

Figure 6.5.1-1. Functional Set-up for Traffic Channel Tests in Fading Channel 23

24

3GPP2 C.S0011-C v2.0

6-20

Mobile StationUnder Test

AWGNGenerator

Rx/Tx

Ioc

Io

Base Station1

Tx

Rx

Base Station2

Tx

Rx

ChannelSimulator 1

Ior1

ChannelSimulator 2

Ior2 Ior2^

Ior1^Σ

1

Figure 6.5.1-2. Functional Set-up for Traffic Channel Tests in Soft Handoff 2

3

Mobile StationUnder Test

AWGNGenerator

Rx/Tx

Ioc

Io

Base Station1

Tx

Rx

Base Station2

Tx

Rx

Ior1

Ior2 Ior2^

Ior1^Σ

4

Figure 6.5.1-3. Functional Set-up for Searcher and Traffic Channel Tests in Soft 5

Handoff 6

3GPP2 C.S0011-C v2.0

6-21

1

2


Tx

Rx

Rx/Tx

Ior IoIor^

AWGNGenerator

Ioc

Interference Generator:(1 or 2 CW tones,

or 1 modulated signal )

Power

Σ

3

Figure 6.5.1-4. Functional Set-up for Tests Without Fading 4

5

Figure 6.5.1-5. Functional Set-up for Tests With Transmit Diversity 6

7

6.5.2 General Comments 8

The following comments apply to all CDMA tests: 9

1. The Forward CDMA Channel may be comprised of a Pilot Channel, a Sync 10

Channel, a Paging Channel or Primary Broadcast Control Channel and Common 11

Control Channel, a Traffic Channel (either Fundamental Channel or Dedicated 12

Control Channel for Radio Configuration 3 through 9, or Packet Data Channel for 13

Radio Configuration 10), and other orthogonal channels (OCNS). 14

2. Whenever a Sync channel is needed to perform a test and its power ratios is not 15

specified in the test parameters table, use Sync Ec/Ior equal to -16 dB. Whenever a 16

Paging Channel is needed to perform a test and its power ratio is not specified in 17


Tx1

Rx

Rx/Tx

ChannelSimulator 1

Ioc

Ior1 Io1Ior1^Σ

Tx2

AWGNGenerator

ChannelSimulator 2

Ior2 Ior2^Σ

ΣIo2

Io

3GPP2 C.S0011-C v2.0

6-22

the test parameters table, use Paging Ec/Ior equal to -12 dB with Paging Channel 1

data rate at 4800 bps. Whenever Broadcast Control and Forward Common Control 2

Channels are needed to perform a test, and their data rates or power ratios are not 3

specified in the test parameters table, use BCCH at 9600 bps with 1/4 rate coding 4

and BCCH Ec/Ior equal to –12 dB and F-CCCH at 9600 bps with 1/4 rate coding 5

and F-CCCH Ec/Ior equal to –12 dB. 6

3. Adjust the OCNS gain such that the power ratios (Ec/Ior) of all specified forward 7

channels add up to one. 8

4. During handoff tests, Channel 2 from base station 2 always has a relative delay of 9

12 μs from Channel 1 from base station 1 at the mobile station antenna connector. 10

The transmission of Forward Traffic Channel frames on Channel 2 shall be enabled 11

prior to sending the Universal Handoff Direction Message on Channel 1 to initiate 12

the handoff with Channel 2. 13

5. Pilot PN sequence offset indices are denoted by Pi (i = 1, 2, 3, ...). The following 14

assumptions hold unless otherwise specified: 15

• 0 ≤ Pi ≤ 511 16

• Pi ≠ Pj if i ≠ j 17

• Pi mod PILOT_INC = 0 18

6. Base stations should be configured for normal operation as specified in [4] unless 19

specifically stated differently in a specific test. 20

7. Unless otherwise specified, the Reverse Traffic Channel should be operated at a 21

sufficiently high Eb/N0 to ensure insignificant (for example, less than 10-5) frame 22

error rate. 23

8. For a mobile station with an integral antenna, the manufacturer shall provide a 24

calibrated RF coupling fixture to provide connection to the standard test 25

equipment. 26

10. Overhead message fields should be those needed for normal operation of the base 27

station unless stated differently below or in a specific test. 28

11. Unless otherwise specified, the Nominal Reverse Common Channel Attribute Gain 29

Table and Reverse Link Nominal Attribute Gain Table values specified in Section 30

2.1.2.3.3.1 and 2.1.2.3.3.2 of [4], respectively, shall apply. 31

12. Unless specified otherwise in test procedures, if the mobile station supports turbo 32

coding on the Reverse Supplemental Channel, the test shall be performed with 33

turbo coding of the Reverse Supplemental Channel; otherwise, the mobile station 34

shall use convolutional coding of the Reverse Supplemental Channel. 35

13. If F-PDCCH is used in a test, the base station shall not send any message with the 36

MAC_ID field set to ‘00000000’ on the F-PDCCH except during initialization. 37

14. Values of time limits and other constants should be as specified in [6]. Values of 38

some time limits and constants are listed below for reference. 39

3GPP2 C.S0011-C v2.0

6-23

1

Constant Value Unit N2m 12 20 ms

N3m 2 20 ms

N11m 1 20 ms

N16m 384 1.25 ms

N17m 64 1.25 ms

T1b 1.28 seconds

T5m 5 seconds

T61m 0.08 seconds

T72m 1 seconds

2

15. On each Primary Paging Channel that the base station transmits, the base station 3

shall send each of the following messages at least every T1b seconds as specified in 4

3.6.2.2 of [6], unless specified otherwise in test procedures: 5

1. Access Parameters Message 6

2. CDMA Channel List Message 7

3. System Parameters Message 8

4. Extended System Parameters Message 9

5. 10

• Neighbor List Message when operating in Band Class 0 and 11

MIN_P_REV is less than seven; or 12

• Extended Neighbor List Message when operating in Band Class 1, 13

Band Class 3, or Band Class 4 and MIN_P_REV is less than seven; 14

otherwise, 15

• General Neighbor List Message. 16

16. On each Broadcast Control Channel that the base station transmits, the base 17

station shall send each of the following system overhead messages at least every 18

T1b seconds on a continuous basis, consecutively as specified in 3.6.2.2 of [6].: 19

1. Extended CDMA Channel List Message 20

2. ANSI-41 System Parameters Message 21

3. MC-RR Parameters Message 22

4. Enhanced Access Parameters Message 23

5. Universal Neighbor List Message 24

17. Special field values for some messages are listed below. 25

3GPP2 C.S0011-C v2.0

6-24

1

Access Parameters Message: 2

3


NOM_PWR 0 (0 dB)

NOM_PWR_EXT 0 (0 dB)

INIT_PWR 0 (0 dB)

PWR_STEP 0 (0 dB)

NUM_STEP 4 (5 probes per sequence)

4

Enhanced Access Parameters Message: 5

6


NOM_PWR_EACH 0 (0 dB)

INIT_PWR_EACH 0 (0 dB)

PWR_STEP_EACH 0 (0 dB)

NUM_STEP_EACH 4 (5 probes per sequence)

RLGAIN_COMMON_PILOT 0 (0 dB)

NUM_MODE_SELECTION_ENTRIES 0 (only one access mode specified)

ACCESS_MODE 0 (Basic Access Mode)

NUM_MODE_PARAM_REC 0 (only Basic Access Mode specific parameter records)

APPLICABLE_MODES 1 (Parameters are for Basic Access Mode)

EACH_NOM_PWR 0 (0 dB)

EACH_INIT_PWR 0 (0 dB)

EACH_PWR_STEP 0 (0 dB)

EACH_NUM_STEP 4 (5 probes per sequence)

NUM_EACH_BA 1 (one Enhanced Access Channel)

EACH_BA_RATES_SUPPORTED 0 (9600 bps, 20 ms frame size)

7

3GPP2 C.S0011-C v2.0

6-25

System Parameters Message: 1

2


REG_PRD 0 (timer-based registration off)

SRCH_WIN_A 8 (60 chips)

SRCH_WIN_N 8 (60 chips)

SRCH_WIN_R 8 (60 chips)

NGHBR_MAX_AGE 0 (minimum amount of Neighbor Set aging)

PWR_THRESH_ENABLE 0 (threshold reporting off)

PWR_PERIOD_ENABLE 0 (periodic reporting off)

T_ADD 28 (-14 dB Ec/I0)

T_DROP 32 (-16 dB Ec/I0)

T_COMP 5 (2.5 dB)

T_TDROP 3 (4 sec)

QPCH_SUPPORTED 0 (QPCH disabled)

3

Extended System Parameters Message and MC-RR Parameters Message: 4

5


SOFT_SLOPE 0 (0)

RLGAIN_TRAFFIC_PILOT 0 (0 dB)

FOR_PDCH_SUPPORTED 1 (supported)

PDCH_CHM_SUPPORTED 0 (not supported)

NUM_PDCCH 0 (1)

RLGAIN_ACKCH_PILOT 0 (0 dB)

RLGAIN_CQICH_PILOT 0 (0 dB)

6

3GPP2 C.S0011-C v2.0

6-26

Neighbor List Message for base station 1: 1

Note that pilot PN offset index P1 is listed in the Neighbor List Message for base 2

station 2. 3

4


PILOT_INC 12

NGHBR_CONFIG 0

NGHBR_PN P2

NGHBR_CONFIG 0

NGHBR_PN P3

NGHBR_CONFIG 0

NGHBR_PN P4

NGHBR_CONFIG 0

NGHBR_PN P5

NGHBR_CONFIG 0

NGHBR_PN P6

NGHBR_CONFIG 0

NGHBR_PN P7

NGHBR_CONFIG 0

NGHBR_PN P8

NGHBR_CONFIG 0

NGHBR_PN P9

5

3GPP2 C.S0011-C v2.0

6-27

Neighbor List Message for base station 2: 1

Note that pilot PN offset index P2 is listed in the Neighbor List Message for base 2

station 1. 3

4


PILOT_INC 12

NGHBR_CONFIG 0

NGHBR_PN P1

NGHBR_CONFIG 0

NGHBR_PN P3

NGHBR_CONFIG 0

NGHBR_PN P4

NGHBR_CONFIG 0

NGHBR_PN P5

NGHBR_CONFIG 0

NGHBR_PN P6

NGHBR_CONFIG 0

NGHBR_PN P7

NGHBR_CONFIG 0

NGHBR_PN P8

NGHBR_CONFIG 0

NGHBR_PN P9

5

3GPP2 C.S0011-C v2.0

6-28

Extended Neighbor List Message for base station 1: 1

Note that pilot PN offset index P1 is listed in the Extended Neighbor List Message for 2

base station 2. 3


PILOT_INC 12

NGHBR_CONFIG 0

NGHBR_PN P2

SEARCH_PRIORITY 1

FREQ_INCL 1

NGHBR_BAND 1

NGHBR_FREQ f2

NGHBR_CONFIG 0

NGHBR_PN P3

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P4

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P5

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P6

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P7

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P8

SEARCH_PRIORITY 3

FREQ_INCL 0

4

3GPP2 C.S0011-C v2.0

6-29

Extended Neighbor List Message for base station 2: 1

Note that pilot PN offset index P2 is listed in the Extended Neighbor List Message for 2

base station 1. 3


PILOT_INC 12

NGHBR_CONFIG 0

NGHBR_PN P1

SEARCH_PRIORITY 1

FREQ_INCL 1

NGHBR_BAND 1

NGHBR_FREQ f1

NGHBR_CONFIG 0

NGHBR_PN P3

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P4

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P5

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P6

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P7

SEARCH_PRIORITY 3

FREQ_INCL 0

NGHBR_CONFIG 0

NGHBR_PN P8

SEARCH_PRIORITY 3

FREQ_INCL 0

3GPP2 C.S0011-C v2.0

6-30

1

Universal Neighbor List Message for base station 1: 2

Note that pilot PN offset index P1 is listed in the Universal Neighbor List Message for 3

base station 2. 4

5



NGHBR_SRCH_MODE 0 (no priorities or windows)

NUM_NGHBR 8 (8 neighbors)

NGHBR_CONFIG 0

NGHBR_PN P2

NGHBR_CONFIG 0

NGHBR_PN P3

NGHBR_CONFIG 0

NGHBR_PN P4

NGHBR_CONFIG 0

NGHBR_PN P5

NGHBR_CONFIG 0

NGHBR_PN P6

NGHBR_CONFIG 0

NGHBR_PN P7

NGHBR_CONFIG 0

NGHBR_PN P8

NGHBR_CONFIG 0

NGHBR_PN P9

6

3GPP2 C.S0011-C v2.0

6-31

Universal Neighbor List Message for base station 2: 1

Note that pilot PN offset index P2 is listed in the Universal Neighbor List Message for 2

base station 1 3

. 4



NGHBR_SRCH_MODE 0 (no priorities or windows)

NUM_NGHBR 8 (8 neighbors)

NGHBR_CONFIG 0

NGHBR_PN P1

NGHBR_CONFIG 0

NGHBR_PN P3

NGHBR_CONFIG 0

NGHBR_PN P4

NGHBR_CONFIG 0

NGHBR_PN P5

NGHBR_CONFIG 0

NGHBR_PN P6

NGHBR_CONFIG 0

NGHBR_PN P7

NGHBR_CONFIG 0

NGHBR_PN P8

NGHBR_CONFIG 0

NGHBR_PN P9

5

Extended Supplemental Channel Assignment Message: 6

7


RLGAIN_SCH_PILOT 0 (0 dB)

8

3GPP2 C.S0011-C v2.0

6-32

Extended Channel Assignment Message when the Forward Packet Data Channel is 1

used: 2

3


EXT_CH_IND 3 (F-PDCH + F-FCH + R-FCH)

REV_ACKCH_REPS 0 (1)

NUM_PDCCH 0 (1)

4

18. Values of counters maintained by the mobile station are listed below for reference. 5

6

Counter Identifier

Description

PAG_1 Number of Paging Channel encapsulated PDUs the mobile station attempted to receive, see 2.1.2.4.3 of [5].

PAG_2 Number of Paging Channel encapsulated PDUs received by the mobile station with a CRC that does not match, see 2.1.2.4.3 of [5].

PAG_3 Number of Paging Channel messages or records received by the mobile station that were addressed to it, see 2.1.2.2 of [5].

PAG_4 Number of Paging Channel half-frames received by the mobile station, see 2.1.2.4.3 of [5].

PAG_5 Number of Paging Channel half-frames that contain any part of a message with a CRC that matches, see 2.1.2.4.3 of [5].

PAG_7 Number of mobile station idle handoffs, see 2.4.2 of [6].

7

6.6 Confidence Limits 8

6.6.1 Confidence Level of Error Rate 9

When it is required that an error rate (e.g. FER or MER) of a given test be less than a 10

specified value with confidence level C, the procedure for a one-sided confidence limit is 11

applied. This procedure assumes that all errors occur independently, resulting in a Poisson 12

distribution of errors during the test. Since test procedures do not specify either the test 13

duration or the number of errors that are allowed, the error rate at the specified confidence 14

level is computed after the test is completed. Alternatively, if sufficiently few errors occur 15

during the test, the test may be halted when the desired confidence level on the error rate 16

is achieved. 17

In order to have a confidence level C that the true error rate is less than the specified error 18

rate, the measured error rate shall be less than 19

3GPP2 C.S0011-C v2.0

6-33

p’ = 2pk/χ2(1−C,2k), 1

where p’ is the measured error rate, p is the specified error rate, and k is the number of 2

errors that occur during the test. In this expression, χ2(α, n) is the value x such that P(X > 3

x) = α, where X is a chi-squared distributed random variable with n degrees of freedom. 4

Values for χ2(α, n) can be found in various tables. Equivalently stated, satisfying this 5

expression means that the true error rate has probability C of being less than the specified 6

error rate. 7

Figures 6.6.1-1 and 6.6.1-2 provide curves of the demonstrated performance as a fraction 8

of the targeted specification versus the number of errors measured in the tests for 9

confidence levels of 95% and 90%, respectively. The test duration can be determined by 10

dividing the number of errors by the demonstrated error rate. From the figure, as the 11

number of errors becomes large, the measured error rate becomes very close to the 12

specified error rate. This means that if the true error rate is close to the specified error rate, 13

the test time can become increasingly long. 14

Figure 6.6.1-3 through 6.6.1-5 provide curves of maximum FER as a function of the 15

number of frames tested for specified frame error rates of 0.01, 0.05 and 0.1 with 95% 16

confidence level, respectively. Figure 6.6.1-6 provides a curve of maximum FER as a 17

function of the number of frames tested for the specified frame error rate of 0.1 with 90% 18

confidence level. 19

If no errors occur during a test, the test may be terminated when the test time is sufficient 20

to ensure that the confidence level has been demonstrated for the specified error rate. This 21

is done by assuming one error could have occurred at the end of the test, and by applying 22

the criteria stated above with k = 1 23

24

3GPP2 C.S0011-C v2.0

6-34

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1 10 100 1000

Number of Errors, k

Mea

sure

d/Sp

ecif

ied

FER

Rat

io

1

Figure 6.6.1-1. Ratio (Measured/Specified) Bound as a Function of Number of Errors 2

(k) for 95% Confidence 3

4

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1 10 100 1000

Number of Errors, k

Mea

sure

d/Sp

ecif

ied

FER

Rat

io

5

Figure 6.6.1-2. Ratio (Measured/Specified) Bound as a Function of Number of Errors 6

(k) for 90% Confidence 7

8

3GPP2 C.S0011-C v2.0

6-35

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

100 1000 10000 100000

Test duration (Frames)

Max

imu

m A

llow

able

Tes

t FE

R (%

)

1

Figure 6.6.1-3. Test Requirement for 95% Confidence of FER = 0.01 2

3

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

10 100 1000 10000 100000


Max

imu

m A

llow

able

Tes

t FE

R (%

)

4


6

3GPP2 C.S0011-C v2.0

6-36

0.0

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0

10 100 1000 10000 100000


Max

imu

m A

llow

able

Tes

t FE

R (%

)

1


3

0.0

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0

10 100 1000 10000


Max

imu

m A

llow

able

Tes

t FE

R (%

)

4


6

6.6.2 Confidence on Power Measurement During Fading 7

During fading tests, the average power over the test can be estimated based on the 8

assumption that fade samples spaced about one half wavelength apart are independent. 9

Under this assumption, the standard deviation of power decreases as the square root of the 10

3GPP2 C.S0011-C v2.0

6-37

number of independent samples in the test. Then at a given speed the time between 1

independent samples is computed as (3600/1000) × (λ/2×ν), where λ is the wavelength in 2

meters and ν is the vehicle speed in kilometers per hour. 3

Figures 6.6.2-1 through 6.6.2-3 show the standard deviation of average power as a 4

function of both band class and test duration (in seconds) for four fading cases (Channel 5

Simulator Configuration 1, 3, 4 and 6 as specified in Table 6.4.1.3-1). In these cases the 6

standard deviation of the individual samples depends on the number and amplitudes of the 7

paths specified for each test, and the time between independent samples was determined 8

from the speed specified for the test. The minimum test duration requirements based on a 9

power measurement uncertainty requirement of 0.2 dB are summarized in Table 6.6.2-1. 10

11

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

1.1

1.2

1.3

1.4

1.5

1.6

1.7

1.8

1.9

1 10 100 1000

Time Duration (s)

Mea

sure

d M

ean

Pow

er S

td D

ev (d

B)

2-paths, 8km/h1-path, 30km/h3-paths, 100km/h1-path, 3km/h

12

Figure 6.6.2-1. Uncertainty in Power Measurement in Rayleigh Fading for Band Group 13

800 14

15

Deleted: Band Classes 0, 2, 3, 7, 9 and 10

3GPP2 C.S0011-C v2.0

6-38

0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1

1.1

1.2

1.3

1 10 100 1000

Time Duration (s)

Mea

sure

d M

ean

Pow

er S

td D

ev (d

B)


1

Figure 6.6.2-2. Uncertainty in Power Measurement in Rayleigh Fading for Band group 2

1900 3

4

00.10.20.30.40.50.60.70.80.9

11.11.21.31.41.51.61.71.81.9

22.12.22.32.42.52.6

1 10 100 1000

Time Duration (s)

Mea

sure

d M

ean

Pow

er S

td D

ev (d

B)


5

Figure 6.6.2-3. Uncertainty in Power Measurement in Rayleigh Fading for Band group 6

450 7

8


Deleted: Band Class 5

3GPP2 C.S0011-C v2.0

6-39

Table 6.6.2-1. Minimum Test Duration Requirements 1


1 2 3 4 6

Band Group

Time (s)

frames Time (s)

frames Time (s)

frames Time (s)

frames Time (s)

frames

450 50 2500 14 700 30 1500 3 150 300 15000

800 30 1500 8 400 20 1000 2 100 200 10000

1900 10 500 6 300 7 350 2 100 70 3500

The minimum test duration specified in frames is based on a frame length of 20ms. 2

3

6.6.3 Confidence Level of Detection Time 4

Several tests involve the successful detection of a strong pilot, or the successful loss 5

detection of a weak pilot. Tests of this type require that the time to have a successful 6

outcome be less than a specified value, T, with probability, p, and confidence level, C. One 7

method to establish a confidence level from the measurements is to declare an error if the 8

time to success exceeds the specified time, T. Assume that k errors occur during N 9

repeated tests. The method used in 6.6.1 can be used to determine the confidence level of 10

the test by replacing p' with k/N. The resulting requirement on k, in order to have a 11

confidence level C that the true error rate is less than the specified error rate, is that k 12

satisfy the relationship: 13

χ2(1−C,2k) = 2Np. 14

15

Deleted: Band Class

Deleted: 5 and 11

Deleted: 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

6-40

No text.1

3GPP2 C.S0011-C v2.0

A-1

ANNEX A: SELECTED PERFORMANCE REQUIREMENTS TABLES 1

This annex is normative. 2

A.1 Forward Common Channel Performance Tables 3

A.1.1 Non-Slotted Mode Paging Channel Performance Requirements 4

These requirements are referenced by 3.3.1. 5

A.1.1.1 Method of Measurement Test Parameters 6

Table A.1.1.1-1. Test Parameters for Non-Slotted Mode Paging Channel Performance 7

in AWGN 8

Parameter Unit Value

Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Sync

dB -16

orc

IEPaging dB -16.2


t

bN

EPaging dB 3.9

Note: The Paging Eb/Nt value is calculated from the parameters 9

in the table. It is not a directly settable parameter. 10

A.1.1.2 Minimum Standards Requirements 11

Table A.1.1.2-1. Minimum Standards for Non-Slotted Mode Paging Channel 12

Performance in AWGN 13

PCH Eb/Nt [dB]

MER

3.5 0.055

3.9 0.035

4.1 0.03

14

3GPP2 C.S0011-C v2.0

A-2

A.1.2 Slotted Mode Paging Channel Performance Requirements 1



Table A.1.2.1-1. Test Parameters for Slotted Mode Paging Channel for Spreading Rate 4

1 (Test 1) 5

Parameter Unit Value Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Sync

dB -16

or

cI

EPaging Quick dB -10

or

cI

EPaging dB -16.2


Quick Paging Data Rate bps 4800

Paging Data Rate bps 9600

t

bN

E QPCH dB 13.1

t

bN

EPaging dB 3.9

Note: The Quick Paging Eb/Nt and Paging Eb/Nt values 6

are calculated from the parameters in the table. They are 7

not directly settable parameters. 8

9

3GPP2 C.S0011-C v2.0

A-3


1 (Test 2) 2


Îor/Ioc dB -6.5

orc

IEPilot dB -7

orc

IE Sync

dB -16

or

cI

EPaging Quick dB -10

orc

IEPaging dB -10.7

Ioc dBm/1.23 MHz -48.5

Quick Paging Data Rate bps 4800

Paging Data Rate bps 9600

t

bN

E QPCH dB 7.6

t

bN

EPaging dB 3.9




6

3GPP2 C.S0011-C v2.0

A-4


3 (Test 3) 2

Parameter Unit Value Îor/Ioc dB Not specified

orc

IEPilot dB Not specified

orc

IE Sync

dB Not specified

or

cI

EPaging Quick dB Not specified

orc

IEPaging dB Not specified

Ioc dBm/1.23 MHz Not specified

Quick Paging Data Rate bps Not specified

Paging Data Rate bps Not specified

t

bN

E QPCH dB Not specified

t

bN

EPaging dB Not specified




6

3GPP2 C.S0011-C v2.0

A-5


3 (Test 4) 2


Îor/Ioc dB Not specified

orc

IEPilot dB Not specified

orc

IE Sync

dB Not specified

or

cI

EPaging Quick dB Not specified

orc

IEPaging dB Not specified

Ioc dBm/1.23 MHz Not specified

Quick Paging Data Rate bps Not specified

Paging Data Rate bps Not specified

t

bN

E QPCH dB Not specified

t

bN

EPaging dB Not specified




6



for Spreading Rate 1 in AWGN (Test 1) 9

PCH Eb/Nt [dB]

MER

3.5 0.055

3.9 0.035

4.1 0.03

10

3GPP2 C.S0011-C v2.0

A-6



PCH Eb/Nt [dB]

MER

3.5 Not specified

3.9 Not specified

4.1 Not specified

3



PCH Eb/Nt [dB]

MER

Not specified Not specified



6



PCH Eb/Nt [dB]

MER




9

A.1.3 Forward Broadcast Control Channel Performance Requirements in AWGN Channel 10


3GPP2 C.S0011-C v2.0

A-7



Spreading Rate 1 with Rate = 1/4 Code, No Transmit Diversity 3


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E BCCH dB -18.7 -15.7 -12.7

or

cI

E CCCH-F dB -7


Data Rate bps 4800 (160 ms) 9600 (80 ms) 19200 (40 ms)

t

bN

E BCCH dB 4.4 4.3 4.3

Note: The BCCH Eb/Nt values are calculated from the parameters in the table. They are 4


6


Spreading Rate 1 with Rate = 1/2 Code, No Transmit Diversity 8


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E BCCH dB -18.3 -15.2 -12.3

or

cI

E CCCH-F dB -7



t

bN

E BCCH dB 4.8 4.8 4.8



11

3GPP2 C.S0011-C v2.0

A-8


Spreading Rate 3 2


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E BCCH dB Not specified Not specified Not specified

or

cI

E CCCH-F dB Not specified



t

bN




5

3GPP2 C.S0011-C v2.0

A-9



AWGN for Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity 3

Test Data Rate BCCH Eb/Nt [dB] FER

3.8 0.05

4.0 0.03

1 4800 (160 ms) 4.4 0.01

4.7 0.005

4.8 0.003

3.8 0.05

4.0 0.03

2 9600 (80 ms) 4.3 0.01

4.6 0.005

4.7 0.003

3.7 0.05

3.9 0.03

3 19200 (40 ms) 4.3 0.01

4.6 0.005

4.8 0.003

4

3GPP2 C.S0011-C v2.0

A-10


AWGN for Spreading Rate 1 with R = 1/2 Code, No Transmit Diversity 2


BCCH Eb/Nt [dB] FER

4.3 0.05

4.4 0.03

4 4800 (160 ms) 4.8 0.01

5.0 0.005

5.2 0.003

4.2 0.05

4.4 0.03

5 9600 (80 ms) 4.8 0.01

5.1 0.005

5.3 0.003

4.2 0.05

4.4 0.03

6 19200 (40 ms) 4.8 0.01

5.0 0.005

5.2 0.003

3

3GPP2 C.S0011-C v2.0

A-11


AWGN for Spreading Rate 3 2


BCCH Eb/Nt [dB] FER

Not specified 0.05

Not specified 0.03

7 4800 (160 ms) Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

3

A.1.4 Forward Broadcast Control Channel Performance Requirements in Multipath 4

Fading Channel 5


3GPP2 C.S0011-C v2.0

A-12


Table A.1.4.1-1. Test Parameters for Broadcast Control Channel for Spreading Rate 1 2

with R = 1/4 Code, No Transmit Diversity 3

Parameter Unit Test 1 Test 2 Test 3

Îor/Ioc dB 8

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -14.5

(2): -14.8

(3): -15.4

(1): -17.9

(2): -18.5

(3): -18.9

(1): -21.5

(2): -21.9

(3): -22.2

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 5.4

(2): 5.1

(3): 4.5

(1): 5.0

(2): 4.4

(3): 4.0

(1): 4.4

(2): 4.0

(3): 3.7


1

(1): Band Group 450; (2): Band Group 800; (3): Band Group 1900.

Note: The BCCH Eb/Nt values are calculated from the parameters in the 4

table. They are not directly settable parameters. 5

6

Formatted Table

Deleted: 20.7

Deleted: 24.1

Deleted: 27.7

Deleted: 21.0

Deleted: 24.7

Deleted: 28.1

Deleted: 21.6

Deleted: 25.1

Deleted: 28.4

Deleted: BC 5 and 11

Deleted: BC 0, 2, 3, 7, 9, 10 and 12

Deleted: BC 1, 4, 6 and 8

3GPP2 C.S0011-C v2.0

A-13




Îor/Ioc dB 4

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -11.2

(2): -12.8

(3): -13.9

(1): -16.0

(2): -17.0

(3): -17.9

(1): -20.1

(2): -20.9

(3): -21.5

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-59

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 10.9

(2): 9.3

(3): 8.2

(1): 9.1

(2): 8.1

(3): 7.2

(1): 8.0

(2): 7.2

(3): 6.6


3


Note: The BCCH Eb/Nt values are calculated from the parameters in the table. 3

They are not directly settable parameters. 4

5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-14




Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -12.4

(2): -12.6

(3): -12.7

(1): -15.8

(2): -15.9

(3): -15.9

(1): -19.0

(2): -19.1

(3): -19.0

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-57

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 4.6

(2): 4.4

(3): 4.3

(1): 4.2

(2): 4.1

(3): 4.1

(1): 4.1

(2): 4.0

(3): 4.1


4




5

Formatted Table

Deleted: 15.5

Deleted: 18.9

Deleted: 22.0

Deleted: 15.7

Deleted: 19.0

Deleted: 22.1

Deleted: 15.8

Deleted: 19.0

Deleted: 22.0


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-15




Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -8.4

(2): -9.2

(3): -11.0

(1): -12.2

(2): -14.0

(3): -16.1

(1): -17.0

(2): -18.8

(3): -20.4

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-61

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 15.7

(2): 14.9

(3): 13.1

(1): 14.9

(2): 13.1

(3): 11.0

(1): 13.1

(2): 11.3

(3): 9.7


6




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-16




Îor/Ioc dB 8

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -13.7

(2): -14.1

(3): -14.7

(1): -17.3

(2): -17.9

(3): -18.3

(1): -20.8

(2): -21.3

(3): -21.6

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 6.2

(2): 5.8

(3): 5.2

(1): 5.6

(2): 5.0

(3): 4.6

(1): 5.1

(2): 4.6

(3): 4.3


1




5

Formatted Table

Deleted: 19.9

Deleted: 23.5

Deleted: 27.0

Deleted: 20.3

Deleted: 24.1

Deleted: 27.5

Deleted: 20.9

Deleted: 24.5

Deleted: 27.8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-17




Îor/Ioc dB 4

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -9.8

(2): -11.2

(3): -12.4

(1): -15.0

(2): -16.1

(3): -16.9

(1): -19.4

(2): -20.1

(3): -20.6

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-59

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 12.3

(2): 10.9

(3): 9.7

(1): 10.1

(2): 9.0

(3): 8.2

(1): 8.7

(2): 8.0

(3): 7.5


3




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-18




Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -11.7

(2): -12.0

(3): -12.0

(1): -15.2

(2): -15.4

(3): -15.4

(1): -18.4

(2): -18.5

(3): -18.5

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-57

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 5.3

(2): 5.0

(3): 5.0

(1): 4.9

(2): 4.7

(3): 4.7

(1): 4.7

(2): 4.6

(3): 4.6


4




5

Formatted Table

Deleted: 14.8

Deleted: 18.2

Deleted: 21.4

Deleted: 15.1

Deleted: 18.4

Deleted: 21.5

Deleted: 15.1

Deleted: 18.4

Deleted: 21.5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-19




Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -7.4

(2): -8.0

(3): -9.6

(1): -11.5

(2): -13.2

(3): -15.3

(1): -16.4

(2): -18.3

(3): -19.9

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-61

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 16.7

(2): 16.1

(3): 14.5

(1): 15.6

(2): 13.9

(3): 11.8

(1): 13.7

(2): 11.8

(3): 10.2


6




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-20


with R = 1/4 Code, Orthogonal Transmit Diversity 2


Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -12.6

(2): -12.7

(3): -12.6

(1): -16.0

(2): -16.0

(3): -15.9

(1): -19.1

(2): -19.1

(3): -19.0

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 4.4

(2): 4.3

(3): 4.4

(1): 4.1

(2): 4.1

(3): 4.2

(1): 4.0

(2): 4.0

(3): 4.1


4




5

Formatted Table

Deleted: 8

Deleted: 15.7

Deleted: 19.0

Deleted: 22.1

Deleted: 15.8

Deleted: 19.0

Deleted: 22.1

Deleted: 15.7

Deleted: 18.9

Deleted: 22.0


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-21


1 with R = 1/4 Code, Orthogonal Transmit Diversity 2


Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -13.4

(2): -13.5

(3): -14.1

(1): -16.6

(2): -17.2

(3): -18.4

(1): -20.1

(2): -21.3

(3): -22.4

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 10.7

(2): 10.6

(3): 10.0

(1): 10.5

(2): 9.9

(3): 8.7

(1): 10.0

(2): 8.8

(3): 7.7


6




5

Deleted: 8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-22




Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -11.8

(2): -11.9

(3): -11.7

(1): -15.4

(2): -15.3

(3): -15.2

(1): -18.5

(2): -18.5

(3): -18.4

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 5.2

(2): 5.1

(3): 5.3

(1): 4.7

(2): 4.8

(3): 4.9

(1): 4.6

(2): 4.6

(3): 4.7


4




5

Deleted: 8

Deleted: 14.9

Deleted: 18.4

Deleted: 21.5

Deleted: 15.0

Deleted: 18.3

Deleted: 21.5

Deleted: 14.8

Deleted: 18.2

Deleted: 21.4


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-23




Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -11.6

(2): -11.8

(3): -12.4

(1): -14.8

(2): -15.9

(3): -17.4

(1): -18.9

(2): -20.2

(3): -21.5

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 12.5

(2): 12.3

(3): 11.7

(1): 12.3

(2): 11.2

(3): 9.7

(1): 11.2

(2): 9.9

(3): 8.6


6




5

Deleted: 8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-24


1 with R = 1/4 Code, Space Time Spreading 2


Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -12.8

(2): -12.9

(3): -12.8

(1): -16.0

(2): -16.1

(3): -16.0

(1): -19.1

(2): -19.1

(3): -19.0

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 4.2

(2): 4.1

(3): 4.2

(1): 4.1

(2): 4.0

(3): 4.1

(1): 4.0

(2): 4.0

(3): 4.1


4




5

Formatted Table

Deleted: 8

Deleted: 15.9

Deleted: 19.0

Deleted: 22.1

Deleted: 16.0

Deleted: 19.1

Deleted: 22.1

Deleted: 15.9

Deleted: 19.0

Deleted: 22.0


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-25




Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -13.7

(2): -13.9

(3): -14.5

(1): -16.7

(2): -17.4

(3): -18.6

(1): -20.3

(2): -21.5

(3): -22.5

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 10.4

(2): 10.2

(3): 9.6

(1): 10.4

(2): 9.7

(3): 8.5

(1): 9.8

(2): 8.6

(3): 7.6


6




5

Deleted: 8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-26




Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -12.1

(2): -12.2

(3): -12.1

(1): -15.5

(2): -15.5

(3): -15.4

(1): -18.6

(2): -18.6

(3): -18.4

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN

E BCCH dB (1): 4.9

(2): 4.8

(3): 4.9

(1): 4.6

(2): 4.6

(3): 4.7

(1): 4.5

(2): 4.5

(3): 4.7


4




5

Formatted Table

Deleted: 8

Deleted: 15.2

Deleted: 18.5

Deleted: 21.6

Deleted: 15.3

Deleted: 18.5

Deleted: 21.6

Deleted: 15.2

Deleted: 18.4

Deleted: 21.4


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-27




Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI

E BCCH dB (1): -13.2

(2): -13.2

(3): -13.4

(1): -16.2

(2): -16.6

(3): -18.0

(1): -19.8

(2): -20.8

(3): -21.9

or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate Bps 19200 9600 4800

t

bN

E BCCH dB (1): 10.9

(2): 10.9

(3): 10.7

(1): 10.9

(2): 10.5

(3): 9.1

(1): 10.3

(2): 9.3

(3): 8.2


6




5

6

Deleted: 8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-28


3 2


Îor/Ioc dB 8

orc

IEPilot dB -7

or

cI


or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-63

Data Rate bps 19200 9600 4800

t

bN



1




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-29


3 2


Îor/Ioc dB 4

orc

IEPilot dB -7

or

cI


or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-59

Data Rate bps 19200 9600 4800

t

bN



3




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-30


3 2


Îor/Ioc dB 2

orc

IEPilot dB -7

or

cI


or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-57

Data Rate bps 19200 9600 4800

t

bN



4




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-31


3 2


Îor/Ioc dB 6

orc

IEPilot dB -7

or

cI


or

cI

E CCCH-F dB -7

Ioc dBm/1.23 MHz

-61

Data Rate bps 19200 9600 4800

t

bN



6




5


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-32


Table A.1.4.2-1. Minimum Standards for Broadcast Control Channel Performance for 2

Spreading Rate 1 with R = 1/4 Code, No Transmit Diversity 3

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.4 4.3 3.9 0.10

1 19200 5.4 5.1 4.5 0.05

7.9 6.9 5.9 0.01

4.3 3.8 3.5 0.10

2 9600 5.0 4.4 4.0 0.05

6.8 5.8 5.0 0.01

3.8 3.6 3.3 0.10

3 4800 4.4 4.0 3.7 0.05

5.7 5.0 4.4 0.01

9.2 8.2 7.3 0.10

4 19200 10.9 9.3 8.2 0.05

14.5 12.0 10.0 0.01

7.9 7.2 6.7 0.10

5 9600 9.1 8.1 7.2 0.05

11.6 9.8 8.5 0.01

7.2 6.6 6.2 0.10

6 4800 8.0 7.2 6.6 0.05

9.6 8.4 7.5 0.01

4

Deleted: Band Classes¶5 and 11

Deleted: Band Classes¶0, 2, 3, 7, 9, 10 and 12

Deleted: Band Classes¶1, 4, 6 and 8

3GPP2 C.S0011-C v2.0

A-33



BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.1 4.0 4.0 0.10

7 19200 4.6 4.4 4.3 0.05

5.4 5.1 5.0 0.01

3.9 3.8 3.8 0.10

8 9600 4.2 4.1 4.1 0.05

5.0 4.8 4.8 0.01

3.8 3.7 3.8 0.10

9 4800 4.1 4.0 4.1 0.05

4.7 4.6 4.7 0.01

13.0 12.2 11.0 0.10

10 19200 15.7 14.9 13.1 0.05

22.2 20.4 17.6 0.01

12.4 11.2 9.4 0.10

11 9600 14.9 13.1 11.0 0.05

19.7 17.6 14.7 0.01

11.2 9.7 8.4 0.10

12 4800 13.1 11.3 9.7 0.05

17.1 14.9 12.1 0.01

3




3GPP2 C.S0011-C v2.0

A-34



BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

5.2 4.9 4.6 0.10

13 19200 6.2 5.8 5.2 0.05

8.7 7.7 6.6 0.01

4.8 4.4 4.2 0.10

14 9600 5.6 5.0 4.6 0.05

7.3 6.3 5.5 0.01

4.5 4.2 3.9 0.10

15 4800 5.1 4.6 4.3 0.05

6.3 5.6 5.0 0.01

10.5 9.6 8.8 0.10

16 19200 12.3 10.9 9.7 0.05

16.4 13.8 11.8 0.01

8.8 8.1 7.6 0.10

17 9600 10.1 9.0 8.2 0.05

12.6 10.8 9.4 0.01

7.9 7.4 7.0 0.10

18 4800 8.7 8.0 7.5 0.05

10.5 9.2 8.3 0.01

3




3GPP2 C.S0011-C v2.0

A-35



BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.9 4.7 4.7 0.10

19 19200 5.3 5.0 5.0 0.05

6.2 5.8 5.6 0.01

4.5 4.4 4.4 0.10

20 9600 4.9 4.7 4.7 0.05

5.6 5.4 5.3 0.01

4.3 4.3 4.3 0.10

21 4800 4.7 4.6 4.6 0.05

5.3 5.1 5.2 0.01

13.7 13.2 12.3 0.10

22 19200 16.7 16.1 14.5 0.05

23.8 22.1 19.5 0.01

12.9 11.9 10.1 0.10

23 9600 15.6 13.9 11.8 0.05

20.4 18.2 15.5 0.01

11.7 10.1 9.1 0.10

24 4800 13.7 11.8 10.2 0.05

18.0 15.5 12.6 0.01

3




3GPP2 C.S0011-C v2.0

A-36


Spreading Rate 1 with R = 1/4 Code, Orthogonal Transmit Diversity 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.1 4.0 4.1 0.10

25 19200 4.4 4.3 4.4 0.05

5.1 4.9 5.0 0.01

3.8 3.8 3.9 0.10

26 9600 4.1 4.1 4.2 0.05

4.8 4.8 4.9 0.01

3.7 3.8 3.8 0.10

27 4800 4.0 4.0 4.1 0.05

4.6 4.7 4.8 0.01

9.1 9.0 8.7 0.10

28 19200 10.7 10.6 10.0 0.05

14.4 13.9 12.7 0.01

9.0 8.6 7.8 0.10

29 9600 10.5 9.9 8.7 0.05

13.9 12.7 10.7 0.01

8.7 7.8 7.0 0.10

30 4800 10.0 8.8 7.7 0.05

12.6 10.9 9.2 0.01

3




3GPP2 C.S0011-C v2.0

A-37


Spreading Rate 1 with R = 1/2 Code, Orthogonal Transmit Diversity 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.9 4.8 4.9 0.10

31 19200 5.2 5.1 5.3 0.05

5.9 5.8 5.9 0.01

4.4 4.5 4.6 0.10

32 9600 4.7 4.8 4.9 0.05

5.3 5.3 5.5 0.01

4.3 4.3 4.5 0.10

33 4800 4.6 4.6 4.7 0.05

5.3 5.1 5.3 0.01

10.9 10.4 10.2 0.10

34 19200 12.5 12.3 11.7 0.05

16.5 16.0 14.7 0.01

10.7 10.0 8.6 0.10

35 9600 12.3 11.2 9.7 0.05

15.4 13.9 12.0 0.01

9.9 8.8 7.9 0.10

36 4800 11.2 9.9 8.6 0.05

14.1 12.1 10.3 0.01

3




3GPP2 C.S0011-C v2.0

A-38


Spreading Rate 1 with R = 1/4 Code, Space Time Spreading 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

3.9 3.8 3.9 0.10

37 19200 4.2 4.1 4.2 0.05

4.9 4.8 4.8 0.01

3.8 3.7 3.8 0.10

38 9600 4.1 4.0 4.1 0.05

4.6 4.7 4.8 0.01

3.7 3.7 3.8 0.10

39 4800 4.0 4.0 4.1 0.05

4.6 4.6 4.7 0.01

8.8 8.6 8.4 0.10

40 19200 10.4 10.2 9.6 0.05

14.1 13.6 12.4 0.01

8.8 8.4 7.5 0.10

41 9600 10.4 9.7 8.5 0.05

13.7 12.4 10.5 0.01

8.4 7.6 6.8 0.10

42 4800 9.8 8.6 7.6 0.05

12.5 10.7 9.2 0.01

3




3GPP2 C.S0011-C v2.0

A-39


for Spreading Rate 1 with R = 1/2 Code, Space Time Spreading 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

4.5 4.5 4.6 0.10

43 19200 4.9 4.8 4.9 0.05

5.5 5.4 5.5 0.01

4.3 4.3 4.5 0.10

44 9600 4.6 4.6 4.7 0.05

5.2 5.1 5.2 0.01

4.2 4.3 4.4 0.10

45 4800 4.5 4.5 4.7 0.05

5.1 5.1 5.2 0.01

9.4 9.4 9.4 0.10

46 19200 10.9 10.9 10.7 0.05

14.7 14.5 13.5 0.01

9.4 9.0 8.1 0.10

47 9600 10.9 10.5 9.1 0.05

14.4 13.0 11.1 0.01

9.0 8.3 7.5 0.10

48 4800 10.3 9.3 8.2 0.05

13.1 11.2 9.8 0.01

3




3GPP2 C.S0011-C v2.0

A-40


Spreading Rate 3 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

Not specified Not specified Not specified 0.10

49 19200 Not specified Not specified Not specified 0.05

















3




3GPP2 C.S0011-C v2.0

A-41


Spreading Rate 3 2

BCCH Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER



















3

A.1.5 Forward Common Control Channel Performance Requirements 4





3GPP2 C.S0011-C v2.0

A-42



Spreading Rate 1 with Rate = 1/4 Mode, No Power Control, No Transmit Diversity 3


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E FCCCH dB -13.3 -10.2 -10.0



t

bN

E FCCCH dB 3.8 3.9 4.1

Note: The FCCCH Eb/Nt value is calculated from the parameters in the table. It is not a 4

directly settable parameter. 5

6




Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E FCCCH dB -12.8 -9.8 -9.5



t

bN

E FCCCH dB 4.3 4.3 4.6



11

3GPP2 C.S0011-C v2.0

A-43


Spreading Rate 3 with Rate = 1/4 Mode, No Power Control 2


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E FCCCH dB Not specified Not specified Not specified



t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI




t

bN




10

3GPP2 C.S0011-C v2.0

A-44





FCCCH Eb/Nt [dB] FER

3.1 0.05

3.3 0.03

1 19200 (10 ms) 3.8 0.01

4.1 0.005

4.3 0.003

3.2 0.05

3.4 0.03

2 38400 (5 ms) 3.9 0.01

4.1 0.005

4.3 0.003

3.5 0.05

3.7 0.03

3 38400 (10 ms) 4.1 0.01

4.4 0.005

4.6 0.003

4

3GPP2 C.S0011-C v2.0

A-45





3.7 0.05

3.9 0.03

4 19200 (10 ms) 4.3 0.01

4.5 0.005

4.7 0.003

3.8 0.05

4.0 0.03

5 38400 (5 ms) 4.3 0.01

4.5 0.005

4.6 0.003

4.0 0.05

4.2 0.03

6 38400 (10 ms) 4.6 0.01

4.8 0.005

5.0 0.003

3

3GPP2 C.S0011-C v2.0

A-46





Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

3

3GPP2 C.S0011-C v2.0

A-47





Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03


Not specified 0.005

Not specified 0.003

3

A.1.6 Common Assignment Channel and Common Power Control Channel Performance 4

Requirements 5


3GPP2 C.S0011-C v2.0

A-48


Table A.1.6.1-1. Test Parameters for the Common Assignment Channel for Spreading 2

Rate 1 with Rate = 1/4 mode in AWGN, No Transmit Diversity 3


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E CACH dB -17

or

cI

E CPCCH dB -17.8


CACH Data Rate bps 9600

t

bN

E CACH dB 3.1

Note: The CACH Eb/Nt value is calculated from the 4

parameters in the table. It is not a directly settable 5

parameter. 6

7

3GPP2 C.S0011-C v2.0

A-49


Rate 1 with Rate = 1/2 mode in AWGN, No Transmit Diversity 2


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E CACH dB -16.5

or

cI

E CPCCH dB -17.8



t

bN

E CACH dB 3.6



parameter. 5

6


Rate 3 in AWGN 8


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E CACH dB Not specified

or

cI

E CPCCH dB Not specified



t

bN

E CACH dB Not specified



parameter. 11

12

3GPP2 C.S0011-C v2.0

A-50


Table A.1.6.2-1. Minimum Standards for Common Assignment Channel for Spreading 2

Rate 1 with Rate = 1/4 Mode in AWGN 3

CACH Eb/Nt [dB]

FER

2.3 0.05

2.6 0.03

3.1 0.01

3.5 0.005

3.7 0.003

4

Table A.1.6.2-2 Minimum Standards for Common Assignment Channel for Spreading 5

Rate 1 with Rate = 1/2 Mode in AWGN 6

CACH Eb/Nt [dB]

FER

2.8 0.05

3.1 0.03

3.6 0.01

3.9 0.005

4.1 0.003

7

Table A.1.6.2-3. Minimum Standards for Common Assignment Channel for Spreading 8

Rate 3 in AWGN 9

CACH Eb/Nt [dB]

FER

Not Specified 0.05

Not Specified 0.03

Not Specified 0.01

Not Specified 0.005

Not Specified 0.003

10

3GPP2 C.S0011-C v2.0

A-51

A.2 Forward Traffic Channel Demodulation Performance Tables 1

A.2.1 Forward Traffic Channel Performance Requirements in AWGN 2




Channel in AWGN 6


Îor/Ioc dB -1

or

cI

E Pilot dB -7

or

cI

E Traffic dB -16.3 -15.8 -15.6


Data Rate bps 9600 9600 9600

t

bN

E Traffic dB 3.8 4.3 4.5

Note: The Traffic Eb/Nt value is calculated from the parameters in the table. It is not a 7


9

3GPP2 C.S0011-C v2.0

A-52


Channel in AWGN 2


Îor/Ioc dB -1

or

cI

E Pilot dB -7

or

cI

E Traffic dB -19.1 -21.6 -24.5


Data Rate bps 4800 2400 1200

t

bN




5


Channel in AWGN 7


Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -13.0 (2): -12.9

(1): -12.7 (2): -12.5

(1): -12.4 (2): -12.3

Ioc dBm/ 1.23 MHz

-54

Data Rate bps 14400 14400 14400

t

bN

E Traffic dB (1): 5.3

(2): 5.4 (1): 5.6 (2): 5.8

(1): 5.9 (2): 6.0

(1): Band Group 450 and 800; (2): BC 1, 4, 6, 8, 14 and 15.



10

Deleted: BC 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: and

3GPP2 C.S0011-C v2.0

A-53


Channel in AWGN 2


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E Traffic dB (1): -17.3

(2): -17.2 (1): -20.8 (2): -20.7

(1): -24.4 (2): -24.3

Ioc dBm/ 1.23 MHz

-54

Data Rate bps 7200 3600 1800

t

bN


(2): 4.1 (1): 3.5 (2): 3.6

(1): 2.9 (2): 3.0

(1): Band Group 450 and 800; (2): BC 1, 4, 6, 8, 14 and 15.



5


Channel or Forward Dedicated Control Channel with 100% Frame Activity in AWGN 7

Parameter Units Test 13 Test 14 Test 15 Test 16 Test 17 Test 18

Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -17.5 -16.9 -16.7 -16.6 -16.2 -15.9

Ioc dBm/1.23 MHz

-54

Data Rate bps 9600 (5 ms) 9600

t

bN

E Traffic dB 2.6 3.2 3.4 3.5 3.9 4.2



10

Deleted: BC 0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: and

3GPP2 C.S0011-C v2.0

A-54




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -19.3 -21.9 -24.9


Data Rate bps 4800 2700 1500

t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -16.9 -16.4 -16.1 -15.9 -15.4 -15.1

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB 3.2 3.7 4.0 4.2 4.7 5.0



10

3GPP2 C.S0011-C v2.0

A-55




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -18.8 -21.5 -24.6


Data Rate bps 4800 2700 1500

t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -17.5 -17.0 -16.7 -14.2 -13.8 -13.6

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB 2.6 3.1 3.4 4.1 4.5 4.7



10

3GPP2 C.S0011-C v2.0

A-56




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB -17.2 -20.6 -24.1


Data Rate bps 7200 3600 1800

t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB Not specified

Not specified

Not specified

Not specified

Not specified

Not specified

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-57




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB Not specified Not specified Not specified


Data Rate bps 4800 2700 1500

t

bN

E Traffic dB Not specified Not specified Not specified



5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB Not specified

Not specified

Not specified

Not specified

Not specified

Not specified

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-58




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic



Data Rate bps 4800 2700 1500

t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB Not specified

Not specified

Not specified

Not specified

Not specified

Not specified

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-59




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic



Data Rate bps 7200 3600 1800

t

bN




5




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic

dB Not specified

Not specified

Not specified

Not specified

Not specified

Not specified

Ioc dBm/1.23 MHz

-54


t

bN

E Traffic dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-60




Îor/Ioc dB -1

orc

IEPilot dB -7

orc

IE Traffic



Data Rate bps 7200 3600 1800

t

bN




5


Code Channel in AWGN 7


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E SCCH dB -17.0 -16.7 -16.1

orc

IE Traffic

dB -12


Data Rate bps 9600 9600 9600

t

bN

E SCCH dB 3.1 3.4 4.0

Note: The Supplemental Code Channel Eb/Nt value is calculated from the parameters 8

in the table. It is not a directly settable parameter. 9

10

3GPP2 C.S0011-C v2.0

A-61


Code Channel in AWGN 2


Îor/Ioc dB -1

orc

IEPilot dB -7

or

cI

E SCCH dB -13.7 -13.5 -13.0

orc

IE Traffic

dB -12


Data Rate bps 14400 14400 14400

t

bN

E SCCH dB 4.6 4.8 5.3

Note: The Supplemental Code Channel Eb/Nt value is calculated from the parameters in 3

the table. It is not a directly settable parameter. 4

5


Channel with 100% Frame Activity in AWGN with Convolutional Coding 7


Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -13.6 -10.3 -7.0 -3.7

orc

IE Traffic

dB -7


Data Rate bps 19200 38400 76800 153600

t

bN

E SCH dB 3.5 3.8 4.0 4.3

Note: The Supplemental Channel Eb/Nt value is calculated from the parameters in the 8


10

3GPP2 C.S0011-C v2.0

A-62


Channel with 100% Frame Activity in AWGN with Turbo Coding 2


Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -14.8 -12.1 -9.1 -6.1

orc

IE Traffic

dB -7


Data Rate bps 19200 38400 76800 153600

t

bN

E SCH dB 2.2 2.0 1.9 1.9

Note: The Supplemental Eb/Nt value is calculated from the parameters in the table. It is 3

not a directly settable parameter. 4

5



Parameter Units Test 90 Test 91 Test 92 Test 93 Test 94

Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -13.1 -9.8 -6.5 -3.3 Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200

t

bN

E SCH dB 4.0 4.3 4.5 4.7 Not

specified



10

3GPP2 C.S0011-C v2.0

A-63




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -14.0 -11.2 -8.2 -5.3 Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200

t

bN

E SCH dB 3.1 2.9 2.8 2.7 Not

specified



5




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -11.4 -8.1 -4.9 -1.6

orc

IE Traffic

dB -7


Data Rate bps 28800 57600 115200 230400

t

bN

E SCH dB 3.9 4.2 4.4 4.7



10

3GPP2 C.S0011-C v2.0

A-64




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB -12.8 -9.9 -7.0 -4.0

orc

IE Traffic

dB -7


Data Rate bps 28800 57600 115200 230400

t

bN

E SCH dB 2.6 2.4 2.3 2.2



5




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-65




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified



5




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200 614400

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-66




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 19200 38400 76800 153600 307200 614400

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



5




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 28800 57600 115200 230400 460800

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-67




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 28800 57600 115200 230400 460800

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified



5




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 28800 57600 115200 230400 460800 1036800

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



10

3GPP2 C.S0011-C v2.0

A-68




Îor/Ioc dB -1

orc

IEPilot

dB -7

or

cI

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified

orc

IE Traffic

dB -7

Ioc dBm/1.23 MHz

-54

Data Rate bps 28800 57600 115200 230400 460800 1036800

t

bN

E SCH dB Not

specified Not

specified Not

specified Not

specified Not

specified Not

specified



5

3GPP2 C.S0011-C v2.0

A-69


Table A.2.1.2-1. Minimum Standards for Radio Configuration 1 Forward Fundamental 2

Channel Performance in AWGN 3

Test(s) Data Rate [bps]

Traffic Eb/Nt [dB]

FER

3.6 0.05

3.8 0.03

1, 2, 3 9600 4.3 0.01

4.5 0.005

4.7 0.003

3.6 0.03

4 4800 4.0 0.01

4.2 0.005

4.0 0.03

5 2400 4.5 0.01

4.8 0.005

3.9 0.03

6 1200 4.6 0.01

4.9 0.005

4

3GPP2 C.S0011-C v2.0

A-70


Channel Performance in AWGN 2


Traffic Eb/Nt [dB]

FER

5.2 0.05

5.5 0.03

7, 8, 9 14400 5.8 0.01

6.0 0.005

6.2 0.003

3.7 0.03

10 7200 4.1 0.01

4.4 0.005

3.1 0.03

11 3600 3.6 0.01

3.9 0.005

2.5 0.03

12 1800 3.0 0.01

3.4 0.005

3

3GPP2 C.S0011-C v2.0

A-71


Channel or Forward Dedicated Control Channel with 100% Frame Activity 2



Traffic Eb/Nt [dB]

FER

2.3 0.05

2.6 0.03

13, 14, 15 9600 (5 ms) 3.2 0.01

3.4 0.005

3.6 0.003

3.3 0.05

3.5 0.03

16, 17, 18 9600 3.9 0.01

4.2 0.005

4.4 0.003

3.2 0.03

19 4800 3.8 0.01

4.2 0.005

3.1 0.03

20 2700 3.7 0.01

4.0 0.005

2.5 0.03

21 1500 3.2 0.01

3.5 0.005

4

3GPP2 C.S0011-C v2.0

A-72





Traffic Eb/Nt [dB]

FER

2.9 0.05

3.2 0.03

22, 23, 24 9600 (5 ms) 3.7 0.01

4.0 0.005

4.2 0.003

4.0 0.05

4.2 0.03

25, 26, 27 9600 4.7 0.01

5.0 0.005

5.1 0.003

3.8 0.03

28 4800 4.3 0.01

4.5 0.005

3.6 0.03

29 2700 4.1 0.01

4.4 0.005

2.9 0.03

30 1500 3.5 0.01

3.9 0.005

4

3GPP2 C.S0011-C v2.0

A-73





Traffic Eb/Nt [dB]

FER

2.3 0.05

2.6 0.03

31, 32, 33 9600 (5 ms) 3.1 0.01

3.4 0.005

3.6 0.003

3.9 0.05

4.1 0.03

34, 35, 36 14400 4.5 0.01

4.7 0.005

4.8 0.003

3.5 0.03

37 7200 4.1 0.01

4.4 0.005

3.2 0.03

38 3600 3.7 0.01

4.0 0.005

2.6 0.03

39 1800 3.2 0.01

3.6 0.005

4

3GPP2 C.S0011-C v2.0

A-74





Traffic Eb/Nt [dB]

FER

Not specified 0.05

Not specified 0.03

40, 41, 42 9600 (5 ms) Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03

43, 44, 45 9600 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.03

46 4800 Not specified 0.01

Not specified 0.005

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

4

3GPP2 C.S0011-C v2.0

A-75





Traffic Eb/Nt [dB]

FER

Not specified 0.05

Not specified 0.03

49, 50, 51 9600 (5 ms) Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03

52, 53, 54 9600 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

4

3GPP2 C.S0011-C v2.0

A-76





Traffic Eb/Nt [dB]

FER

Not specified 0.05

Not specified 0.03

58, 59, 60 9600 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03

61, 62, 63 14400 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

4

3GPP2 C.S0011-C v2.0

A-77





Traffic Eb/Nt [dB]

FER

Not specified 0.05

Not specified 0.03

67, 68, 69 9600 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.05

Not specified 0.03

70, 71, 72 14400 Not specified 0.01

Not specified 0.005

Not specified 0.003

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

Not specified 0.03


Not specified 0.005

4


Supplemental Code Channel Performance in AWGN 6

Tests Data Rate [bps]

SCCH Eb/Nt [dB]

FER

3.1 0.1

76, 77, 78 9600 3.4 0.05

4.0 0.01

7

3GPP2 C.S0011-C v2.0

A-78


Supplemental Code Channel Performance in AWGN 2

Tests Data Rate [bps]

SCCH Eb/Nt [dB]

FER

4.6 0.1

79, 80, 81 14400 4.8 0.05

5.3 0.01

3



Convolutional Coding 6


SCH Eb/Nt [dB] FER

3.1 0.1

82 19200 3.5 0.05

4.1 0.01

3.5 0.1

83 38400 3.8 0.05

4.4 0.01

3.7 0.1

84 76800 4.0 0.05

4.6 0.01

4.0 0.1

85 153600 4.3 0.05

4.8 0.01

7

3GPP2 C.S0011-C v2.0

A-79


Supplemental Channel Performance with 100% Frame Activity in AWGN with Turbo 2

Coding 3


SCH Eb/Nt [dB] FER

2.1 0.1

86 19200 2.2 0.05

2.5 0.01

1.9 0.1

87 38400 2.0 0.05

2.3 0.01

1.8 0.1

88 76800 1.9 0.05

2.1 0.01

1.8 0.1

89 153600 1.9 0.05

1.9 0.01

4

3GPP2 C.S0011-C v2.0

A-80





SCH Eb/Nt [dB] FER

3.7 0.1

90 19200 4.0 0.05

4.5 0.01

4.0 0.1

91 38400 4.3 0.05

4.8 0.01

4.3 0.1

92 76800 4.5 0.05

5.0 0.01

4.5 0.1

93 153600 4.7 0.05

5.2 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-81



Coding 3


SCH Eb/Nt [dB] FER

2.9 0.1

95 19200 3.1 0.05

3.4 0.01

2.8 0.1

96 38400 2.9 0.05

3.2 0.01

2.7 0.1

97 76800 2.8 0.05

3.0 0.01

2.7 0.1

98 153600 2.7 0.05

2.8 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-82





SCH Eb/Nt [dB] FER

3.7 0.1

100 28800 3.9 0.05

4.5 0.01

3.9 0.1

101 57600 4.2 0.05

4.7 0.01

4.2 0.1

102 115200 4.4 0.05

5.0 0.01

4.4 0.1

103 230400 4.7 0.05

5.2 0.01

4

3GPP2 C.S0011-C v2.0

A-83



Coding 3


SCH Eb/Nt [dB] FER

2.4 0.1

104 28800 2.6 0.05

2.8 0.01

2.3 0.1

105 57600 2.4 0.05

2.6 0.01

2.2 0.1

106 115200 2.3 0.05

2.4 0.01

2.2 0.1

107 230400 2.2 0.05

2.3 0.01

4

3GPP2 C.S0011-C v2.0

A-84





SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-85



Coding 3


SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-86





SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-87



Coding 3


SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-88





SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-89



Coding 3


SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-90


Supplemental Channel Performance in with 100% Frame Activity AWGN with 2



SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

3GPP2 C.S0011-C v2.0

A-91



Coding 3


SCH Eb/Nt [dB] FER

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

Not specified 0.1


Not specified 0.01

4

A.2.2 Forward Traffic Channel Performance Requirements in Multipath Fading Channel 5


3GPP2 C.S0011-C v2.0

A-92



Configuration 1 in Fading Channel (Case 1) 3


Îor/Ioc dB 8

orc

IEPilot dB -7

or

cI

E Traffic dB (1): -16.1

(2): -16.1 (3): -17.2

(1): -13.5

(2): -13.5 (3): -16.0

(1): -11.5

(2): -11.5 (3): -15.2

Îoc dBm/ 1.23 MHz

-63

Data Rate bps 9600

t

bN


(2): 6.8 (3): 5.7

(1): 9.4

(2): 9.4 (3): 6.9

(1): 11.4

(2): 11.4 (3): 7.7

Channel Simulator

Configuration

1



directly settable parameter. The channel simulator configurations are found in Table 5

6.4.1.3-1 (Note: For Band Class 5 and 11, use 15 km/h vehicle speed). 6

7


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-93




Îor/Ioc dB 0 -4

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -6.2

(2): -6.2

(1): -7.6

(2): -7.6

Îoc dBm/1.23 MHz -55 -51

Data Rate bps 9600

t

bN


(2): 13.1

(1): 8.7

(2): 8.7


1





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-94




Îor/Ioc dB 4

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -12.3

(2): -12.3 (3): -14.4

(1): -9.5

(2): -9.5 (3): -12.4

(1): -7.5

(2): -7.5 (3): -11.3

Îoc dBm/ 1.23 MHz

-59

Data Rate bps 9600

t

bN


(2): 12.8 (3): 10.7

(1): 15.6

(2): 15.6 (3): 12.7

(1): 17.6

(2): 17.6 (3): 13.8

Channel Simulator

Configuration

3





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-95




Îor/Ioc dB 4

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -14.4

(2): -14.4 (3): -17.0

(1): -17.5

(2): -17.5 (3): -20.3

(1): -21.3

(2): -21.3 (3): -23.9

Îoc dBm/ 1.23 MHz

-59

Data Rate bps 4800 2400 1200

t

bN


(2): 13.7 (3): 11.1

(1): 13.6

(2): 13.6 (3): 10.8

(1): 12.8

(2): 12.8 (3): 10.2

Channel Simulator

Configuration

3





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-96



Parameter Units Test 12

Îor/Ioc dB 2

orc

IEPilot dB -7

orc

IE Traffic

(for 9600 bps)

dB (1): -14.7

(2): -14.7 (3): -14.6

Îoc dBm/ 1.23 MHz

-57

Data Rate bps Variable

t

bN


(2): 5.3 (3): 5.5


4





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-97




Îor/Ioc dB 8

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -13.1

(2): -13.1 (3): -13.3

(1): -9.4

(2): -9.4 (3): -10.6

Îoc dBm/ 1.23 MHz

-63

Data Rate bps 14400

t

bN


(2): 8.0 (3): 7.8

(1): 11.7

(2): 11.7 (3): 10.5

Channel Simulator

Configuration

1





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-98




Îor/Ioc dB 12

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -14.3

(2): -14.3

(1): -9.3

(2): -9.3

Îoc dBm/1.23 MHz -67

Data Rate bps 14400

t

bN

E Traffic

dB (1): 17.0

(2): 17.0

(1): 22.0

(2): 22.0


3

(1): Band Group 450; (2): Band Group 800.




6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12

3GPP2 C.S0011-C v2.0

A-99




Îor/Ioc dB 12

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -18.9

(2): -18.9

(1): -23.1

(2): -23.1

(1): -27.2

(2): -27.2

Îoc dBm/1.23 MHz -67

Data Rate bps 7200 3600 1800

t

bN


(2): 15.4

(1): 14.2

(2): 14.2

(1): 13.1

(2): 13.1


3

(1): Band Group 450; (2): Band Group 800.




6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12

3GPP2 C.S0011-C v2.0

A-100




Îor/Ioc dB 2

orc

IEPilot dB -7

orc

IE Traffic

dB (1): -10.3

(2): -10.3

(3): -10.6

(1): -15.7

(2): -15.7

(3): -16.0

(1): -19.6

(2): -19.6

(3): -19.8

(1): -23.4

(2): -23.4

(3): -23.5

Îoc dBm/1.23 MHz

-57

Data Rate bps 14400 7200 3600 1800

t

bN

E Traffic

dB (1): 8.0

(2): 8.0

(3): 7.7

(1): 5.6

(2): 5.6

(3): 5.3

(1): 4.7

(2): 4.7

(3): 4.5

(1): 3.9

(2): 3.9

(3): 3.8

Channel Simulator

Configuration

4





6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-101



Fading Channel (Case 1, Tests 1, 2 and 3) 3

Traffic Eb/Nt [dB]

Band Group 450 and 800

Band Classes

1, 4, 6, 8, 14 and 15

FER

6.0 5.4 0.04

6.8 5.7 0.03

9.4 6.9 0.01

11.4 7.7 0.005

11.9 7.9 0.004

4


Fading Channel (Case 1, Test 4) 6

Traffic Eb/Nt [dB]

FER

10.2 0.03

13.1 0.01

15.1 0.005

7


Fading Channel (Case 1, Test 5) 9

Traffic Eb/Nt

[dB]

FER

5.3 0.3

8.7 0.1

11.1 0.05

10

Deleted: Band Classes ¶0, 2, 3, 5, 7, 9, 10, 11 and 12

Deleted: and

3GPP2 C.S0011-C v2.0

A-102


Fading Channel (Case 2) 2

Traffic Eb/Nt [dB]



Band Classes

1, 4, 6, 8, 14 and 15

FER

12.1 10.1 0.04

12.8 10.7 0.03

6, 7, 8 9600 15.6 12.7 0.01

17.6 13.8 0.005

18.2 14.1 0.004

11.3 9.4 0.03

9 4800 13.7 11.1 0.01

15.3 12.1 0.005

11.1 9.3 0.03

10 2400 13.6 10.8 0.01

15.2 11.7 0.005

10.3 8.7 0.03

11 1200 12.8 10.2 0.01

14.3 11.1 0.005

3

Table A.2.2.2-5. Minimum Standards for Band Classes 0, 2, 3, 5, 7, 9, 10, 11 and 12 4

Fundamental Channel Performance in Fading Channel (Case 3, Test 12) 5

Eb/Nt [dB] FER

(9600 bps)

FER

(4800 bps)

FER

(2400 bps)

FER

(1200 bps)

5.1 2.58 × 10-2 1.18 × 10-2 1.09 × 10-2 1.16 × 10-2

5.6 8.82 × 10-3 4.15 × 10-3 4.45 × 10-3 3.49 × 10-3

6

Table A.2.2.2-6. Minimum Standards for Band Group 1900 Fundamental Channel 7

Performance in Fading Channel (Case 3, Test 12) 8

Eb/Nt [dB] FER (9600 bps) FER (4800 bps) FER (2400 bps) FER (1200 bps)

5.2 1.92 × 10-2 5.50 × 10-2 1.41 × 10-2 1.62 × 10-2

5.7 5.71 × 10-3 1.92 × 10-3 4.22 × 10-3 6.72 × 10-3

9


Deleted: and


3GPP2 C.S0011-C v2.0

A-103



Received Frame Category Band Classes

Transmit

Data Rate [bps]

9600 bps

4800 bps

2400 bps

1200 bps

9600 bps with bit errors

Undetected Bit Errors

9600 N/A 1.67 × 10-5 1.56 × 10-4 4.67 × 10-4 1.71 × 10-2 1.67 × 10-5

4800 1.67 × 10-5 N/A 6.70 × 10-5 6.70 × 10-5 1.34 × 10-4 1.67 × 10-5

2400 1.67 × 10-5 2.44 × 10-4 N/A 3.84 × 10-4 2.44 × 10-4 6.98 × 10-5

0, 2, 3, 5, 7, 9, 10, 11 and 12

1200 3.95 × 10-5 1.67 × 10-5 7.89 × 10-5 N/A 1.97 × 10-4 3.95 × 10-5

3



Received Frame Category

Transmit

Data Rate [bps]

9600 bps

4800 bps

2400 bps

1200 bps

9600 bps with bit errors


9600 N/A 1.67 × 10-5 1.41 × 10-4 1.73 × 10-4 8.80 × 10-3 1.67 × 10-5

4800 1.67 × 10-5 N/A 6.66 × 10-5 2.70 × 10-4 2.23 × 10-4 1.67 × 10-5

2400 1.67 × 10-5 1.67 × 10-5 N/A 1.78 × 10-4 1.17 × 10-4 1.67 × 10-5

1200 1.67 × 10-5 1.67 × 10-5 1.42 × 10-4 N/A 1.67 × 10-5 1.67 × 10-5

6

Table A.2.2.2-9. Minimum Standards for Fundamental Channel Radio Configuration 2 7

Performance in Fading Channel (Case 4, Tests 13 and 14) 8

Traffic Eb/Nt [dB]


Band Group 1900 FER

7.5 7.3 0.04

8.0 7.8 0.03

10.0 9.4 0.01

11.7 10.5 0.005

12.1 10.8 0.004

9



Deleted: Band Classes ¶1, 4, 6, and 8


3GPP2 C.S0011-C v2.0

A-104

Table A.2.2.2-10. Minimum Standards for Fundamental Channel Radio Configuration 1

2 Performance in Fading Channel (Case 5) 2

Traffic Eb/Nt [dB]


Band Group 450

Band Group 800

FER

16.4 16.4 0.04

17.0 17.0 0.03

15, 16 14400 20.0 20.0 0.01

22.0 22.0 0.005

22.6 22.6 0.004

13.7 13.7 0.03

17 7200 15.4 15.4 0.01

16.5 16.5 0.005

12.6 12.6 0.03

18 3600 14.2 14.2 0.01

15.2 15.2 0.005

11.6 11.6 0.03

19 1800 13.1 13.1 0.01

14.1 14.1 0.005

3

Table A.2.2.2-11. Minimum Standards for Fundamental Channel Radio Configuration 4

2 Performance in Fading Channel (Case 6) 5

Traffic Eb/Nt [dB]


Band Group 450

Band Group 800

Band Group 1900

FER

20 14400 7.3 7.3 7.2 0.03

8.5 8.5 8.1 0.005

21 7200 5.0 5.0 4.8 0.03

5.9 5.9 5.6 0.005

22 3600 4.1 4.1 3.9 0.03

5.0 5.0 4.8 0.005

23 1800 3.2 3.2 3.1 0.03

4.3 4.3 4.1 0.005

6






3GPP2 C.S0011-C v2.0

A-105


Fundamental Channel Radio Configuration 2 Performance in Fading Channel (Case 6, 2

Tests 20, 21, 22, and 23) 3

Received Frame Category Transmit

Data Rate

[bps]

14400 bps

7200 bps

3600 bps

1800 bps Undetected Bit Errors

14400 N/A 5.00 × 10-5 3.26 × 10-5 2.28 × 10-4 5.00 × 10-5

7200 4.66 × 10-5 N/A 1.19 × 10-4 8.58 × 10-3 4.00 × 10-5

3600 1.35 × 10-5 7.74 × 10-6 N/A 4.72 × 10-5 1.35 × 10-5

1800 1.44 × 10-5 1.13 × 10-5 1.24 × 10-4 N/A 5.64 × 10-5

4


Fundamental Channel Radio Configuration 2 Performance in Fading Channel (Case 6, 6

Tests 20, 21, 22, and 23) 7

Received Frame Category

Transmit

Data Rate

(bps)

14400 bps

7200 bps

3600 bps

1800 bps


14400 N/A 1.67 × 10-5 2.38 × 10-4 2.73 × 10-4 1.67 × 10-5

7200 1.67 × 10-5 N/A 6.14 × 10-5 1.67 × 10-5 1.67 × 10-5

3600 1.67 × 10-5 1.67 × 10-5 N/A 2.81 × 10-4 1.67 × 10-5

1800 1.43 × 10-4 7.16 × 10-5 7.76 × 10-5 N/A 1.67 × 10-5

8

A.2.3 Forward Fundamental Channel Performance Requirements During Soft Handoff 9



Deleted: Band Class 1, 4, 6 and 8

3GPP2 C.S0011-C v2.0

A-106



Channel During Soft Handoff 3


Îor1/Ioc and Îor2/Ioc dB 10

orc

IEPilot dB -7

orc

IE Traffic

dB -15.3 -13.9 -13.0


t

bN



2



6.4.1.3-1. 6

7



Channel Performance During Soft Handoff 10

Traffic Eb/Nt [dB]

FER

5.1 0.04

5.5 0.03

6.9 0.01

7.8 0.005

8.1 0.004

11

A.2.4 Power Control Bit Performance Requirements for Channels Belonging to Different 12

Power Control Sets During Soft Handoff 13


3GPP2 C.S0011-C v2.0

A-107


Table A.2.4.1-1. Test Parameters for Decision of Power Control Bit for Different 2

Power Control Sets 3


Îor1 dBm/1.23 MHz -55

Îor2 dBm/1.23 MHz -55

orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

orc

IE ControlPower

dB -17.8 (RC 1, 3 and 7)

-21.0 (RC 2, 5 and 9)

4


No text. 6

A.2.5 Power Control Bit Performance Requirements for Channels Belonging to the Same 7

Power Control Set 8


3GPP2 C.S0011-C v2.0

A-108


Table A.2.5.1-1. Test Parameters for Decision of Power Control Bit for the Same 2

Power Control Set 3

Parameter Units Channel 1 Channel 2

Îor dBm/1.23 MHz -55 -58

orc

IEPilot dB -7

orc

IE Traffic

dB -7.4 -7.4 (RC 1, 3 and 7)

-12.5 (RC 2, 5 and 9)

orc

IE ControlPower

dB -17.8 (RC 1, 3 and 7)

-21.0 (RC 2, 5 and 9)

-17.8 (RC 1, 3 and 7)

-26.1 (RC 2, 5 and 9)


5 N/A

Note: The channel simulator configurations are found in Table 6.4.1.3-1. 4


No text. 6

A.2.6 Power Control Subchannel Performance Requirements During Soft Handoff 7


3GPP2 C.S0011-C v2.0

A-109



During Soft Handoff 3

Parameter Units Channel 1 Channel 2

Îor dBm/1.23 MHz Max = -52.2

Min = -55

Max = -55

Min = -65

orc

IEPilot dB -7 -7

orc

IE Traffic

dB -7.4 -12.4 (RC 1, 3 and 7)

-9.2 (RC 2, 5 and 9)

orc

IE ControlPower

dB -17.8 (RC 1, 3 and 7)

-21.0 (RC 2, 5 and 9)

-22.8

0c

IEPilot

dB Max = -7.2

Min = -10

Max = -10

Min = -20

Note: The Pilot Ec/I0 value is calculated from the parameters in the table. It is not a 4


6


No text. 8


with Closed Loop Power Control (FPC_MODE = ‘000’) 10



Note: The Traffic Eb/Nt values specified in this section are calculated from the parameters 13

in Tables A.2.7.1-2 through A.2.7.1-9. Traffic Eb/Nt is not a directly settable parameter. 14

The channel simulator configurations are found in Table 6.4.1.3-1. 15

16

3GPP2 C.S0011-C v2.0

A-110

Table A.2.7.1-1. Test Parameters for Forward Power Control 1


orc

IEPilot

dB -7

Maximum or

cI

E FCHor

or

cI

E DCCH

dB -3

FPC_MODE ‘000’ (800 bps Primary)

FPC_PRI_CHAN 0 (for FCH testing) or

1 (for DCCH testing)

FPC_FCH_INIT_SETPT or FPC_DCCH_INIT_SETPT

FPC_FCH_MIN_SETPT or FPC_DCCH_MIN_SETPT

FPC_FCH_MAX_SETPT or FPC_DCCH_MAX_SETPT

dB

These setpoint values shall be set identical to effectively disable the outer loop. They should be set to

achieve the specified FCH Eb/Nt or DCCH Eb/Nt for each individual test specified in Table A.2.7.1-2

through A.2.7.1-9.

PWR_CNTL_STEP dB 0.5

Reverse Link Delay ms 0.625

FPC_THRESH_INCL 0 (disable FCH/DCCH outer loop report message transmission by

MS)

The initial FCH Ec/Ior or DCCH Ec/Ior transmitted by the base station shall be 2

set to the Ec/Ior value specified in Table A.2.7.1-2 through A.2.7.1-9. 3

Note that the values of the signaling parameters FPC_FCH_INIT_SETPT or 4

FPC_DCCH_INIT_SETPT do not in general correspond to the Eb/Nt values 5

specified in Table A.2.7.1-2 through A.2.7.1-9 or to the Eb/Nt values specified in 6

Table A.2.7.2-1 through A.2.7.2-8. These signaling parameters may be set to 7

any appropriate value in order to achieve the required conditions of this test. 8

The reverse link delay is the time between the end of the power control group 9

with a valid power control bit and the corresponding change in the base station 10

power for the channel under test. 11

12

3GPP2 C.S0011-C v2.0

A-111



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior [dB]

Traffic Eb/Nt [dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 1

9600 (1): -15.6

(2): -16.4

(3): -16.1

(1): 11.5

(2): 10.7

(3): 11.0

2

3 4 -59 9600 (5 ms) N/S N/S 3

9600 (1): -11.7

(2): -13.0

(3): -14.8

(1): 13.4

(2): 12.1

(3): 10.3

4

4 2 -57 9600 (5 ms) N/S N/S 5

9600 (1): -14.1

(2): -14.3

(3): -14.3

(1): 5.9

(2): 5.7

(3): 5.7

6


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-112



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 7

14400 (1): -13.8

(2): -13.7

(3): -14.0

(1): 11.5

(2): 11.6

(3): 11.3

8

3 4 -59 9600 (5 ms) N/S N/S 9

14400 (1): -9.3

(2): -10.2

(3): -12.1

(1): 14.0

(2): 13.1

(3): 11.2

10

4 2 -57 9600 (5 ms) N/S N/S 11

14400 (1): -12.1

(2): -12.2

(3): -12.2

(1): 6.2

(2): 6.1

(3): 6.1

12


3



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 13

9600 N/S N/S 14

3 4 -59 9600 (5 ms) N/S N/S 15

9600 N/S N/S 16

4 2 -57 9600 (5 ms) N/S N/S 17

9600 N/S N/S 18


6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-113



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 19

14400 N/S N/S 20

3 4 -59 9600 (5 ms) N/S N/S 21

14400 N/S N/S 22

4 2 -57 9600 (5 ms) N/S N/S 23

14400 N/S N/S 24


3


Control Channel with 10% Frame Activity 5

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

9600 (5 ms) N/S N/S 25 6 6 -61

9600 N/S N/S 26


6



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

9600 (5 ms) N/S N/S 27 6 6 -61

9600 N/S N/S 28


9


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-114



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

9600 (5 ms) N/S N/S 29 6 6 -61

9600 N/S N/S 30


3



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

9600 (5 ms) N/S N/S 31 6 6 -61

14400 N/S N/S 32


6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-115


Table A.2.7.2-1 Minimum Standards for Radio Configuration 3 Forward Fundamental 2


Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER


1 9600 (5 ms) Not specified Not specified Not specified 0.1


11.0 9.7 9.9 0.2

2 9600 11.5 10.7 11.0 0.1

12.0 11.7 12.0 0.05




11.4 9.9 8.7 0.05

4 9600 13.4 12.1 10.3 0.01

14.2 13.0 10.9 0.005




4.9 4.7 4.7 0.05

6 9600 5.9 5.7 5.7 0.01

6.3 6.0 6.0 0.005

4




3GPP2 C.S0011-C v2.0

A-116



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER




11.0 11.3 10.3 0.2

8 14400 11.5 11.6 11.3 0.1

12.1 12.0 12.3 0.05




12.0 10.7 9.5 0.05

10 14400 14.0 13.1 11.2 0.01

15.0 14.2 12.1 0.005




5.2 5.2 5.2 0.05

12 14400 6.2 6.1 6.1 0.01

6.7 6.5 6.4 0.005

3




3GPP2 C.S0011-C v2.0

A-117



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER



















3




3GPP2 C.S0011-C v2.0

A-118



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER



















3




3GPP2 C.S0011-C v2.0

A-119



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







3



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







6







3GPP2 C.S0011-C v2.0

A-120



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







3



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







6


with Closed Loop Power Control (FPC_MODE = ‘010’) 8



Note: The SCH Eb/Nt values specified in this section are calculated from the parameters in 11

Tables A.2.8.1-2 through A.2.8.1-5. SCH Eb/Nt is not a directly settable parameter. The 12

channel simulator configurations are found in Table 6.4.1.3-1. 13







3GPP2 C.S0011-C v2.0

A-121



orc

IEPilot

dB -7

or

cI

E FCH or

or

cI

E DCCH

dB -7

Maximum or

cI

E SCH dB -3

FPC_MODE ‘010’ (200 bps for FCH/DCCH,

600 bps for SCH)



FPC_FCH_FER or FPC_DCCH_FER

% 1




dB

Not specified

FPC_SCH_INIT_SETPT

FPC_SCH_MIN_SETPT

FPC_SCH_MAX_SETPT

dB


achieve the specified SCH Eb/Nt for each individual test specified in

Table A.2.8.1-2 through A.2.8.1-5.




MS)

FPC_THRESH_SCH_INCL 0 (disable SCH outer loop report message transmission by MS)

3GPP2 C.S0011-C v2.0

A-122

The initial SCH Ec/Ior transmitted by the base station shall be set to the Ec/Ior 1

value specified in Table A.2.8.1-2 through A.2.8.1-5. 2

Note that the value of the signaling parameter FPC_SCH_INIT_SETPT does not in 3

general correspond to the Eb/Nt values specified in Table A.2.8.1-2 through 4

A.2.8.1-5 or to the Eb/Nt values specified in Table A.2.8.2-1 through A.2.8.2-4. 5

This signaling parameter may be set to any appropriate value in order to achieve 6

the required conditions of this test. 7

The reverse link delay is the time between the end of the power control group 8

with a valid power control bit and the corresponding change in the base station 9

power for the channel under test. 10

11


Channel with 100% Frame Activity (Part 1 of 2) 13

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Coding Data Rate [bps]

SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

1 8 -63 Conv. 19200 (1): -15.7

(2): -15.4

(3): -15.2

(1): 4.2

(2): 4.5

(3): 4.6

1

38400 (1): -12.3

(2): -12.1

(3): -12.0

(1): 4.6

(2): 4.8

(3): 4.9

2

153600 (1): -5.6

(2): -5.5

(3): -5.3

(1): 5.2

(2): 5.3

(3): 5.5

3

Turbo 19200 (1): -16.4

(2): -16.2

(3): -16.0

(1): 3.5

(2): 3.7

(3): 3.9

4

38400 (1): -13.5

(2): -13.3

(3): -13.0

(1): 3.4

(2): 3.6

(3): 3.9

5

153600 (1): -7.4

(2): -7.1

(3): -6.9

(1): 3.4

(2): 3.7

(3): 3.9

6


14


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-123



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 38400

(40 ms)

(1): -13.4

(2): -13.8

(3): -18.5

(1): 7.7

(2): 7.3

(3): 2.6

7

38400

(80 ms)

(1): -16.0

(2): -16.5

(3): -17.2

(1): 5.1

(2): 4.6

(3): 3.9

8

Turbo 38400

(40 ms)

(1): -14.5

(2): -15.0

(3): -14.7

(1): 6.6

(2): 6.1

(3): 6.4

9

38400

(80 ms)

(1): -17.3

(2): -17.6

(3): -13.6

(1): 3.8

(2): 3.5

(3): 7.5

10


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-124



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

1 8 -63 Conv. 28800 (1): -13.5

(2): -13.3

(3): -13.1

(1): 4.6

(2): 4.8

(3): 5.0

11

57600 (1): -10.2

(2): -10.0

(3): -9.8

(1): 4.9

(2): 5.1

(3): 5.3

12

230400 (1): -4.0

(2): -4.0

(3): -3.8

(1): 5.1

(2): 5.1

(3): 5.3

13

Turbo 28800 (1): -14.6

(2): -14.3

(3): -14.0

(1): 3.5

(2): 3.8

(3): 4.1

14

57600 (1): -11.6

(2): -11.4

(3): -11.1

(1): 3.5

(2): 3.8

(3): 4.0

15

230400 (1): -5.8

(2): -5.8

(3): -5.5

(1): 3.3

(2): 3.3

(3): 3.6

16


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-125



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 57600

(40 ms)

(1): -11.4

(2): -11.7

(3): -11.2

(1): 7.9

(2): 7.6

(3): 8.1

17

57600

(80 ms)

(1): -13.8

(2): -14.1

(3): -14.7

(1): 5.5

(2): 5.2

(3): 4.6

18

Turbo 57600

(40 ms)

(1): -12.7

(2): -13.1

(3): -12.3

(1): 6.6

(2): 6.2

(3): 7.0

19

57600

(80 ms)

(1): -15.2

(2): -15.5

(3): -16.2

(1): 4.1

(2): 3.8

(3): 3.1

20


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-126


Channel with 100% Frame Activity 2

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

1 8 -63 Conv. 19200 N/S N/S 21

38400 N/S N/S 22

76800 N/S N/S 23

153600 N/S N/S 24

307200 N/S N/S 25

614400 N/S N/S 26

Turbo 19200 N/S N/S 27

38400 N/S N/S 28

76800 N/S N/S 29

153600 N/S N/S 30

307200 N/S N/S 31

614400 N/S N/S 32

6 6 -61 Conv. 38400

(40 ms)

N/S N/S 33

38400

(80 ms)

N/S N/S 34

Turbo 38400

(40 ms)

N/S N/S 35

38400

(80 ms)

N/S N/S 36


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-127



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

1 8 -63 Conv. 28800 N/S N/S 37

57600 N/S N/S 38

115200 N/S N/S 39

230400 N/S N/S 40

460800 N/S N/S 41

1036800 N/S N/S 42

Turbo 28800 N/S N/S 43

57600 N/S N/S 44

115200 N/S N/S 45

230400 N/S N/S 46

460800 N/S N/S 47

1036800 N/S N/S 48

6 6 -61 Conv. 57600

(40 ms)

N/S N/S 49

57600

(80 ms)

N/S N/S 50

Turbo 57600

(40 ms)

N/S N/S 51

57600

(80 ms)

N/S N/S 52


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-128


Table A.2.8.2-1 Minimum Standards for Radio Configuration 3 Forward Supplemental 2


SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

3.7 4.0 4.1 0.1

1 19200 4.2 4.5 4.6 0.05

5.3 5.6 5.7 0.01

4.3 4.3 4.3 0.1

2 38400 4.6 4.8 4.9 0.05

5.6 5.8 6.2 0.01

4.8 4.9 5.0 0.1

3 153600 5.2 5.3 5.5 0.05

6.6 6.7 6.7 0.01

3.1 3.2 3.2 0.1

4 19200 3.5 3.7 3.9 0.05

4.5 4.8 5.0 0.01

3.1 3.2 3.3 0.1

5 38400 3.4 3.6 3.9 0.05

4.3 4.7 5.0 0.01

3.1 3.2 3.3 0.1

6 153600 3.4 3.7 3.9 0.05

4.3 4.7 5.1 0.01

4




3GPP2 C.S0011-C v2.0

A-129



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

7.0 6.5 2.1 0.2

7 38400 (40 ms) 7.7 7.3 2.6 0.1

8.2 8.2 3.2 0.05

4.7 4.0 3.4 0.2

8 38400 (80 ms) 5.1 4.6 3.9 0.1

5.4 5.2 4.4 0.05

5.7 4.9 5.3 0.2

9 38400 (40 ms) 6.6 6.1 6.4 0.1

7.2 7.3 7.4 0.05

3.3 2.6 6.5 0.2

10 38400 (80 ms) 3.8 3.5 7.5 0.1

4.2 4.2 8.4 0.05

3




3GPP2 C.S0011-C v2.0

A-130



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

4.3 4.3 4.5 0.1

11 28800 4.6 4.8 5.0 0.05

5.5 5.9 6.3 0.01

4.6 4.6 4.8 0.1

12 57600 4.9 5.1 5.3 0.05

5.8 6.1 6.6 0.01

4.5 4.6 4.8 0.2

13 230400 5.1 5.1 5.3 0.1

5.5 5.6 5.8 0.05

3.2 3.4 3.6 0.1

14 28800 3.5 3.8 4.1 0.05

4.5 5.0 5.6 0.01

3.2 3.3 3.5 0.1

15 57600 3.5 3.8 4.0 0.05

4.3 4.9 5.3 0.01

2.8 2.8 3.1 0.2

16 230400 3.3 3.3 3.6 0.1

3.5 3.7 5.7 0.05

3




3GPP2 C.S0011-C v2.0

A-131



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

7.2 6.8 7.1 0.2

17 57600 (40 ms) 7.9 7.6 8.1 0.1

8.3 8.5 8.9 0.05

4.9 4.6 4.1 0.2

18 57600 (80 ms) 5.5 5.2 4.6 0.1

5.8 5.7 5.1 0.05

6.2 5.0 6.1 0.2

19 57600 (40 ms) 6.6 6.2 7.0 0.1

7.1 7.4 7.8 0.05

3.5 3.1 2.7 0.2

20 57600 (80 ms) 4.1 3.8 3.1 0.1

4.6 4.4 3.7 0.05

3




3GPP2 C.S0011-C v2.0

A-132



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

























3




3GPP2 C.S0011-C v2.0

A-133



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

























3




3GPP2 C.S0011-C v2.0

A-134



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

























3




3GPP2 C.S0011-C v2.0

A-135



SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

























3


with Outer Loop Power Control and Closed Loop Power Control (FPC_MODE = ‘000’, ‘001’ 5

and ‘010’) 6





3GPP2 C.S0011-C v2.0

A-136


Note: The channel simulator configurations are found in Table 6.4.1.3-1. 2

3

Table A.2.9.1-1. Test Parameters for Slow Power Control in Fading Channel 4


orc

IEPilot

dB -7

Maximum or

cI

E Traffic dB -3




dB 6


dB 0


dB 31.75



FPC_THRESH_INCL 1 (enable FCH/DCCH outer loop report message transmission by

MS)

The initial FCH Ec/Ior or DCCH Ec/Ior transmitted by the base station shall 5

correspond to the minimum performance requirement in Eb/Nt. The reverse link 6

delay is the time between the end of the power control group with a valid power 7

control bit and the corresponding change in the base station power for the 8

channel under test. 9

10

Deleted: 31.875

3GPP2 C.S0011-C v2.0

A-137



Chn. Sim. Config.

Data Rate [bps]

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

FPC_MODE FPC_FCH-_FER

or

FPC_DCCH-_FER

[%]

Test

1 9600 (5 ms) 8 -63 ‘000’ 1 1

‘001’ 1 2

‘010’ 1 3

0 -55 ‘000’ 10 4

9600 8 -63 ‘000’ 1 5

‘001’ 1 6

‘010’ 1 7

0 -55 ‘000’ 10 8

3



Chn. Sim. Config.

Data Rate [bps]

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


or

FPC_DCCH-_FER

[%]

Test

1 9600 (5 ms) 8 -63 ‘000’ 1 9

‘001’ 1 10

‘010’ 1 11

0 -55 ‘000’ 10 12

14400 8 -63 ‘000’ 1 13

‘001’ 1 14

‘010’ 1 15

0 -55 ‘000’ 10 16

6

3GPP2 C.S0011-C v2.0

A-138



Chn. Sim. Config.

Data Rate [bps]

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


or

FPC_DCCH-_FER

[%]

Test

1 9600 (5 ms) 8 -63 ‘000’ 1 17

‘001’ 1 18

‘010’ 1 19

0 -55 ‘000’ 10 20

9600 8 -63 ‘000’ 1 21

‘001’ 1 22

‘010’ 1 23

0 -55 ‘000’ 10 24

3



Chn. Sim. Config.

Data Rate [bps]

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


or

FPC_DCCH-_FER

[%]

Test

1 9600 (5 ms) 8 -63 ‘000’ 1 25

‘001’ 1 26

‘010’ 1 27

0 -55 ‘000’ 10 28

14400 8 -63 ‘000’ 1 29

‘001’ 1 30

‘010’ 1 31

0 -55 ‘000’ 10 32

6

3GPP2 C.S0011-C v2.0

A-139




Traffic Eb/Nt [dB]

Test FPC_MODE FPC_FCH_FER

or

FPC_DCCH_FER

[%]

Band Group 450

Band Group 800

Band Group 1900

1 ‘000’ 1 N/S N/S N/S

2 ‘001’ 1 N/S N/S N/S

3 ‘010’ 1 N/S N/S N/S

4 ‘000’ 10 N/S N/S N/S

5 ‘000’ 1 5.7 6.0 6.0

6 ‘001’ 1 6.0 6.4 6.1

7 ‘010’ 1 6.6 7.0 6.2

8 ‘000’ 10 6.3 6.3 6.2

4



Traffic Eb/Nt [dB]


or

FPC_DCCH_FER

[%]

Band Group 450

Band Group 800

Band Group 1900

9 ‘000’ 1 N/S N/S N/S

10 ‘001’ 1 N/S N/S N/S

11 ‘010’ 1 N/S N/S N/S

12 ‘000’ 10 N/S N/S N/S

13 ‘000’ 1 5.9 6.2 6.5

14 ‘001’ 1 6.3 6.7 6.7

15 ‘010’ 1 7.0 7.4 6.8

16 ‘000’ 10 6.6 6.6 6.7

7







3GPP2 C.S0011-C v2.0

A-140



Traffic Eb/Nt [dB]


or

FPC_DCCH_FER

[%]

Band Group 450

Band Group 800

Band Group 1900

17 ‘000’ 1 N/S N/S N/S

18 ‘001’ 1 N/S N/S N/S

19 ‘010’ 1 N/S N/S N/S

20 ‘000’ 10 N/S N/S N/S

21 ‘000’ 1 N/S N/S N/S

22 ‘001’ 1 N/S N/S N/S

23 ‘010’ 1 N/S N/S N/S

24 ‘000’ 10 N/S N/S N/S

3



Traffic Eb/Nt [dB]


or

FPC_DCCH_FER

[%]

Band Group 450

Band Group 800

Band Group 1900

25 ‘000’ 1 N/S N/S N/S

26 ‘001’ 1 N/S N/S N/S

27 ‘010’ 1 N/S N/S N/S

28 ‘000’ 10 N/S N/S N/S

29 ‘000’ 1 N/S N/S N/S

30 ‘001’ 1 N/S N/S N/S

31 ‘010’ 1 N/S N/S N/S

32 ‘000’ 10 N/S N/S N/S

6







3GPP2 C.S0011-C v2.0

A-141

A.2.10 Forward Traffic Channel Performance Requirements in Multipath Fading with 1

Closed Loop Power Control (FPC_MODE = ‘000’) and Transmit Diversity (OTD or STS) 2






8



orc

IEPilot

dB -7

or

cI

E Pilot TD dB -10

Maximum or

cI

E FCH or

or

cI

E DCCH

dB -3

FPC_MODE ‘000’ (800 bps Primary)






dB


achieve the specified FCH Eb/Nt or DCCH Eb/Nt for each individual test specified in Table A.2.10.1-2

through A.2.10.1-9.




MS)

The initial FCH Ec/Ior or DCCH Ec/Ior transmitted by the base station shall 10

correspond to the minimum performance requirement in Eb/Nt and represent 11

the combined output from all base station RF output ports. The reverse link 12

3GPP2 C.S0011-C v2.0

A-142

delay is the time between the end of the power control group with a valid power 1

control bit and the corresponding change in the base station power for the 2

channel under test. 3

4



Orthogonal Transmit Diversity 7

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 1

9600 (1): -19.5

(2): -19.6

(3): -19.3

(1): 7.6

(2): 7.5

(3): 7.8

2

4 2 -57 9600 (5 ms) N/S N/S 3

9600 (1): -14.3

(2): -14.5

(3): -14.2

(1): 5.7

(2): 5.5

(3): 5.8

4


8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-143


Channel or Forward Dedicated Control Channel (100% Frame Activity) with Space 2

Time Spreading 3

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 5

9600 (1): -19.5

(2): -19.9

(3): -19.6

(1): 7.6

(2): 7.2

(3): 7.5

6

4 2 -57 9600 (5 ms) N/S N/S 7

9600 (1): -14.4

(2): -14.5

(3): -14.4

(1): 5.6

(2): 5.5

(3): 5.6

8


4



Orthogonal Transmit Diversity 7

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 9

14400 (1): -16.9

(2): -17.0

(3): -16.7

(1): 8.4

(2): 8.3

(3): 8.6

10

4 2 -57 9600 (5 ms) N/S N/S 11

14400 (1): -12.0

(2): -12.2

(3): -12.0

(1): 6.3

(2): 6.1

(3): 6.3

12


8


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-144


Channel or Forward Dedicated Control Channel (100% Frame Activity) with Space 2

Time Spreading 3

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 13

14400 (1): -17.9

(2): -17.8

(3): -17.4

(1): 7.4

(2): 7.5

(3): 7.9

14

4 2 -57 9600 (5 ms) N/S N/S 15

14400 (1): -12.4

(2): -12.4

(3): -12.3

(1): 5.9

(2): 5.8

(3): 6.0

16


4


Control Channel (10% Frame Activity) with Orthogonal Transmit Diversity 6

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 17

9600 N/S N/S 18


7


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-145


Control Channel (10% Frame Activity) with Space Time Spreading 2

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 19

9600 N/S N/S 20


3



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 21

14400 N/S N/S 22


6



Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]

Data Rate [bps]

Traffic Ec/Ior

[dB]

Traffic Eb/Nt

[dB]

Test

6 6 -61 9600 (5 ms) N/S N/S 23

14400 N/S N/S 24


9


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-146



Fundamental Channel or Forward Dedicated Control Channel (100% Frame Activity) 3

with Orthogonal Transmit Diversity 4

Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER




7.2 6.9 7.2 0.2

2 9600 7.6 7.5 7.8 0.1

8.1 8.2 8.4 0.05




4.9 4.7 4.9 0.05

4 9600 5.7 5.5 5.8 0.01

6.0 5.9 6.2 0.005

5




3GPP2 C.S0011-C v2.0

A-147



with Space Time Spreading 3

Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER




7.2 6.7 6.9 0.2

6 9600 7.6 7.2 7.5 0.1

8.1 7.7 8.0 0.05




4.8 4.7 4.7 0.05

8 9600 5.6 5.5 5.6 0.01

5.9 5.9 6.0 0.005

4




3GPP2 C.S0011-C v2.0

A-148



with Orthogonal Transmit Diversity 3

Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER




7.8 7.6 7.9 0.2

10 14400 8.4 8.3 8.6 0.1

9.1 9.0 9.2 0.05




5.2 5.3 5.5 0.05

12 14400 6.3 6.1 6.3 0.01

6.5 6.4 6.5 0.005

4




3GPP2 C.S0011-C v2.0

A-149



with Space Time Spreading 3

Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER




7.0 7.0 7.4 0.2

14 14400 7.4 7.5 7.9 0.1

8.0 8.0 8.4 0.05




5.1 5.1 5.2 0.05

16 14400 5.9 5.8 6.0 0.01

6.2 6.1 6.3 0.005

4



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Classes

5 and 11

Band Classes

0, 2, 3, 7, 9, 10 and 12

Band Classes

1, 4, 6 and 8

FER







7




3GPP2 C.S0011-C v2.0

A-150



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







3



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







6







3GPP2 C.S0011-C v2.0

A-151



Traffic Eb/Nt [dB]

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER







3

A.2.11 Forward Traffic Channel Performance Requirements in Multipath Fading with 4

Closed Loop Power Control (FPC_MODE = ‘010’) and Transmit Diversity (OTD or STS) 5






11




3GPP2 C.S0011-C v2.0

A-152



orc

IEPilot

dB -7

or

cI

E Pilot TD dB -10

or

cI

E FCH or

or

cI

E DCCH dB -7

Maximum or

cI

E SCH dB -3

FPC_MODE ‘010’ (200 bps for FCH/DCCH,

600 bps for SCH)



FPC_FCH_FER or FPC_DCCH_FER

% 1




dB

Not specified

FPC_SCH_INIT_SETPT

FPC_SCH_MIN_SETPT

FPC_SCH_MAX_SETPT

dB


achieve the specified SCH Eb/Nt for each individual test specified in

Table A.2.11.1-2 through A.2.11.1-5.




MS)

FPC_THRESH_SCH_INCL 0 (disable SCH outer loop report message transmission by MS)

3GPP2 C.S0011-C v2.0

A-153

The initial SCH Ec/Ior transmitted by the base station shall correspond to the 1

minimum performance requirement in Eb/Nt and represent the combined 2

output from all base station RF output ports. The reverse link delay is the time 3

between the end of the power control group with a valid power control bit and 4

the corresponding change in the base station power for the channel under test. 5

6


Channel (100% Frame Activity) with Orthogonal Transmit Diversity 8

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 38400 (1): -13.5

(2): -13.5

(3): -13.2

(1): 7.6

(2): 7.6

(3): 7.9

1

Turbo 38400 (1): -14.6

(2): -14.5

(3): -14.2

(1): 6.5

(2): 6.6

(3): 6.9

2


9


Channel (100% Frame Activity) with Space Time Spreading 11

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 38400 (1): -13.8

(2): -13.8

(3): -13.5

(1): 7.3

(2): 7.3

(3): 7.6

3

Turbo 38400 (1): -15.0

(2): -15.0

(3): -14.6

(1): 6.1

(2): 6.1

(3): 6.5

4


12


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-154


Channel (100% Frame Activity) with Orthogonal Transmit Diversity 2

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 57600 (1): -11.1

(2): -11.1

(3): -10.7

(1): 8.2

(2): 8.2

(3): 8.6

5

Turbo 57600 (1): -12.1

(2): -12.0

(3): -11.7

(1): 7.2

(2): 7.3

(3): 7.6

6


3


Channel (100% Frame Activity) with Space Time Spreading 5

Chn. Sim.

Config.

Îor/Ioc [dB]

Ioc [dBm/ 1.23 MHz]


SCH Ec/Ior [dB]

SCH Eb/Nt [dB]

Test

6 6 -61 Conv. 57600 (1): -11.8

(2): -11.7

(3): -11.2

(1): 7.5

(2): 7.6

(3): 8.1

7

Turbo 57600 (1): -13.1

(2): -13.0

(3): -12.7

(1): 6.2

(2): 6.3

(3): 6.6

8


6


Deleted: BC 0, 2, 3, 7, 9, 10 and 12



Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-155



Supplemental Channel (100% Frame Activity) with Orthogonal Transmit Diversity 3

SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

7.1 7.1 7.3 0.2

1 38400 7.6 7.6 7.9 0.1

8.0 8.1 8.5 0.05

6.1 6.2 6.4 0.2

2 38400 6.5 6.6 6.9 0.1

6.9 7.0 7.5 0.05

4


Supplemental Channel (100% Frame Activity) with Space Time Spreading 6

SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

6.9 6.9 7.1 0.2

3 38400 7.3 7.3 7.6 0.1

7.6 7.7 8.2 0.05

5.7 5.7 5.9 0.2

4 38400 6.1 6.1 6.5 0.1

6.5 6.6 7.1 0.05

7







3GPP2 C.S0011-C v2.0

A-156


Supplemental Channel (100% Frame Activity) with Orthogonal Transmit Diversity 2

SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

7.6 7.7 8.0 0.2

5 57600 8.2 8.2 8.6 0.1

8.7 8.8 9.2 0.05

6.7 6.7 6.9 0.2

6 57600 7.2 7.3 7.6 0.1

7.7 7.9 8.2 0.05

3


Supplemental Channel (100% Frame Activity) with Space Time Spreading 5

SCH Eb/Nt (dB)

Test Data Rate

[bps]

Band Group 450

Band Group 800

Band Group 1900

FER

7.2 7.2 7.6 0.2

7 57600 7.5 7.6 8.1 0.1

7.9 8.0 8.6 0.05

5.9 5.9 6.1 0.2

8 57600 6.2 6.3 6.6 0.1

6.6 6.7 7.2 0.05

6

A.2.12 Power Control Subchannel Performance Requirements During Reverse Pilot 7

Channel Gating 8








3GPP2 C.S0011-C v2.0

A-157



during Reverse Pilot Channel Gating 3



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

orc

IE ControlPower

dB -17.8



6


No text. 8


Fundamental Channel Gating 10




during Reverse Fundamental Channel Gating 14



orc

IEPilot dB -7

orc

IE Traffic

dB -7.4

orc

IE ControlPower

dB -17.8



3GPP2 C.S0011-C v2.0

A-158

1


No text. 3

3GPP2 C.S0011-C v2.0

A-159

A.2.14 Forward Packet Data Channel Performance Requirements in Additive White 1

Gaussian Noise 2




Channel in AWGN 6


Retransmission No No One One No One

Packet Size Bits 2328 3864 3096 3864 1560 2328

Walsh Channels Number of 28 27 26 26 25 25

Number of Slots 1 2 1 1 1 1

Modulation Order 3 2 4 4 2 3

Îor/Ioc dB 13 10 16.5 20.5 8.5 13

orc

IEPilot

dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -2.4 -2.4 -3.9 -2.1 -2.9 -4.6

Ioc dBm/1.23

MHz -54

Data Rate kbps 1862.4 1545.6 2476.8 3091.2 1248.0 1862.4

t

bN

E PDCH dB 8.8 6.6 9.6 14.4 5.5 6.6

Note: The Packet Data Eb/Nt value is calculated from the parameters in the table. It is not 7

a directly settable parameter. The Data Rate value is also calculated from the parameters in 8


10

3GPP2 C.S0011-C v2.0

A-160


Channel in AWGN 2


Retransmission No No No No One No

Packet Size Bits 3096 3864 2328 2328 3096 3864




Îor/Ioc dB 8.5 12.5 6.5 16.5 18 12.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.1 -3.4 -3.6 -3.1 -3.5 -3.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 1238.4 1545.6 931.2 1862.4 2476.8 1545.6

t

bN

E PDCH dB 5.4 8.1 4.2 11.6 11.4 8.5




6

3GPP2 C.S0011-C v2.0

A-161


Channel in AWGN 2


Retransmission No No No No One No

Packet Size Bits 1560 3096 1560 3096 3096 3864




Îor/Ioc dB 8.5 8.5 11 10.5 19.5 12.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E 0 PDCCH dB -16

or

cI

E PDCH dB -2.4 -2.5 -3.7 -3.6 -3.1 -2.5

Ioc dBm/1.23

MHz -54

Data Rate kbps 1248.0 1238.4 1248.0 1238.4 2476.8 1545.6

tb

NE PDCH

dB 6.1 6.0 7.3 6.9 13.3 9.0




6

3GPP2 C.S0011-C v2.0

A-162


Channel in AWGN 2


Retransmission No No No No No No

Packet Size Bits 1560 2328 2328 2328 3096 408




Îor/Ioc dB 5 2.5 6.5 16.5 4.5 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.4 -4.0 -3.1 -2.4 -4.2 -5.6

Ioc dBm/1.23

MHz -54

Data Rate kbps 624.0 465.6 931.2 1862.4 619.2 326.4

tb

NE PDCH

dB 3.5 2.7 4.6 12.3 3.3 2.7




6

3GPP2 C.S0011-C v2.0

A-163


Channel in AWGN 2



Packet Size Bits 792 792 1560 3096 3864 3864




Îor/Ioc dB 2.5 5.5 11 10.5 6 16

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -5.8 -4.7 -3.2 -3.1 -4.0 -3.8

Ioc dBm/1.23

MHz -54

Data Rate kbps 316.8 633.6 1248.0 1238.4 772.8 1545.6

tb

NE PDCH

dB 2.6 3.7 7.7 7.33 4.0 11.2




6

3GPP2 C.S0011-C v2.0

A-164


Channel in AWGN 2


Retransmission One No No No No One

Packet Size Bits 2328 1560 2328 3096 3864 2328




Îor/Ioc dB 16.5 11 6.5 10.5 16 16.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.7 -2.6 -2.5 -2.5 -3.2 -4.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 1862.4 1248.0 931.2 1238.4 1545.6 1862.4

tb

NE PDCH

dB 10.0 8.3 5.2 8.0 11.8 10.7




6

3GPP2 C.S0011-C v2.0

A-165


Channel in AWGN 2



Packet Size Bits 3096 3864 792 1560 1560 2328




Îor/Ioc DB 4.5 6 5.5 5 13.5 8.5

or

cI

E Pilot DB -7

or

cI

E Sync DB -16

or

cI

EPaging DB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.9 -3.4 -4.2 -3.9 -3.7 -3.3

Ioc dBm/1.23

MHz -54

Data Rate kbps 619.2 772.8 633.6 624 1248.0 931.2

tb

NE PDCH

dB 3.6 4.6 4.2 4.0 9.7 6.4




6

3GPP2 C.S0011-C v2.0

A-166


Channel in AWGN 2



Packet Size Bits 3096 3864 1560 2328 3864 3864




Îor/Ioc dB 13.5 16 2.5 2.5 6 16

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.9 -2.5 -5.7 -3.5 -2.9 -2.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 1238.4 1545.6 312.0 465.6 772.8 1545.6

tb

NE PDCH

dB 9.6 12.5 2.7 3.2 5.2 13.0




6

3GPP2 C.S0011-C v2.0

A-167


Channel in AWGN 2



Packet Size Bits 792 1560 1560 2328 3096 3096




Îor/Ioc dB 5.5 5 13.5 8.5 4.5 13.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.7 -3.5 -3.0 -2.5 -3.3 -3.1

Ioc dBm/1.23

MHz -54

Data Rate kbps 633.6 624 1248.0 931.2 619.2 1238.4

tb

NE PDCH

dB 4.7 4.5 10.5 7.2 4.2 10.4




6

3GPP2 C.S0011-C v2.0

A-168


Channel in AWGN 2


Retransmission One No No No No No

Packet Size Bits 3864 1560 3096 3864 408 792




Îor/Ioc dB 16 13.5 13.5 8 2.5 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.5 -2.5 -2.6 -3.7 -5.0 -8.8

Ioc dBm/1.23

MHz -54

Data Rate kbps 1545.6 1248.0 1238.4 772.8 326.4 158.4

tb

NE PDCH

dB 10.5 10.9 10.9 6.3 3.2 2.6




6

3GPP2 C.S0011-C v2.0

A-169


Channel in AWGN 2



Packet Size Bits 792 792 1560 1560 2328 2328




Îor/Ioc dB 2.5 5.5 5 13.5 2.5 11.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -5.3 -2.9 -2.8 -1.9 -3.0 -4.1

Ioc dBm/1.23

MHz -54

Data Rate kbps 316.8 633.6 624 1248.0 465.6 931.2

tb

NE PDCH

dB 3.1 5.4 5.2 11.5 3.7 8.6




6

3GPP2 C.S0011-C v2.0

A-170


Channel in AWGN 2



Packet Size Bits 3096 3096 3864 792 1560 2328




Îor/Ioc dB 4.5 13.5 8 6.5 6.5 11.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -2.5 -2.1 -3.2 -3.4 -3.6 -3.6

Ioc dBm/1.23

MHz -54

Data Rate kbps 619.2 1238.4 772.8 633.6 624.0 931.2

tb

NE PDCH

dB 4.9 11.4 6.8 6.0 5.8 9.1




6

3GPP2 C.S0011-C v2.0

A-171


Channel in AWGN 2



Packet Size Bits 3096 792 1560 1560 2328 2328




Îor/Ioc dB 6 6.5 2.5 6.5 2.5 11.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.3 -2.9 -5.2 -3.1 -2.3 -3.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 619.2 633.6 312.0 624.0 465.6 931.2

tb

NE PDCH

dB 5.7 6.5 3.3 6.4 4.4 9.7




6

3GPP2 C.S0011-C v2.0

A-172


Channel in AWGN 2



Packet Size Bits 3096 3864 408 408 792 792




Îor/Ioc dB 6 10 2.5 2.5 2.5 8.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -2.8 -4.0 -8.4 -4.5 -4.8 -4.2

Ioc dBm/1.23

MHz -54

Data Rate kbps 619.2 772.8 163.2 326.4 316.8 633.6

tb

NE PDCH

dB 6.2 8.0 2.9 3.8 3.6 7.2




6

3GPP2 C.S0011-C v2.0

A-173


Channel in AWGN 2



Packet Size Bits 1560 2328 2328 3096 3864 408




Îor/Ioc dB 8.5 4.5 11.5 8 10 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.4 -3.6 -2.2 -4.2 -3.4 -4.1

Ioc dBm/1.23

MHz -54

Data Rate kbps 624.0 465.6 931.2 619.2 772.8 326.4

tb

NE PDCH

dB 7.1 5.1 10.5 6.8 8.7 4.2




6

3GPP2 C.S0011-C v2.0

A-174


Channel in AWGN 2



Packet Size Bits 792 792 1560 1560 2328 3096




Îor/Ioc dB 2.5 8.5 2.5 8.5 4.5 8

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.4 -3.5 -4.6 -3.8 -3.0 -3.6

Ioc dBm/1.23

MHz -54

Data Rate kbps 316.8 633.6 312.0 624.0 465.6 619.2

tb

NE PDCH

dB 4.0 7.9 3.9 7.7 5.7 7.4




6

3GPP2 C.S0011-C v2.0

A-175


Channel in AWGN 2


Retransmission Bits No No No No No No

Packet Size Bits 3864 408 792 792 792 1560




Îor/Ioc dB 10 2.5 2.5 2.5 8.5 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -2.5 -3.4 -8.4 -3.8 -2.6 -4.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 772.8 326.4 158.4 316.8 633.6 312.0

tb

NE PDCH

dB 9.5 4.8 3.0 4.6 8.8 4.4




6

3GPP2 C.S0011-C v2.0

A-176


Channel in AWGN 2



Packet Size Bits 1560 2328 3096 408 408 792




Îor/Ioc dB 8.5 8 8 2.5 2.5 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -2.9 -5.4 -2.7 -7.9 -2.6 -3.0

Ioc dBm/1.23

MHz -54

Data Rate kbps 624.0 465.6 619.2 163.2 326.4 316.8

tb

NE PDCH

dB 8.6 6.8 8.3 3.4 5.6 5.4




6

3GPP2 C.S0011-C v2.0

A-177


Channel in AWGN 2



Packet Size Bits 1560 2328 408 408 408 792




Îor/Ioc dB 2.5 8 2.5 2.5 6 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -3.2 -4.5 -11.4 -7.5 -5.0 -7.8

Ioc dBm/1.23

MHz -54

Data Rate kbps 312.0 465.6 81.6 163.2 326.4 158.4

tb

NE PDCH

dB 5.2 7.7 2.9 3.8 6.7 3.6




6

3GPP2 C.S0011-C v2.0

A-178


Channel in AWGN 2



Packet Size Bits 792 1560 2328 408 408 408




Îor/Ioc dB 5 5 8 2.5 2.5 6

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -4.5 -4.7 -3.1 -11.2 -6.5 -3.4

Ioc dBm/1.23

MHz -54

Data Rate kbps 316.8 312.0 465.6 81.6 163.2 326.4

tb

NE PDCH

dB 6.4 6.2 9.1 3.1 4.8 8.4




6

3GPP2 C.S0011-C v2.0

A-179


Channel in AWGN 2



Packet Size Bits 792 792 1560 408 408 792




Îor/Ioc dB 2.5 5 5 2.5 2.5 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -6.8 -3.0 -3.2 -10.5 -5.0 -5.3

Ioc dBm/1.23

MHz -54

Data Rate kbps 158.4 316.8 312.0 81.6 163.2 158.4

tb

NE PDCH

dB 4.6 7.9 7.7 3.8 6.3 6.1




6

3GPP2 C.S0011-C v2.0

A-180


Channel in AWGN 2

Parameter Units Test 127

Retransmission No

Packet Size Bits 408

Walsh Channels Number of 1

Number of Slots 4

Modulation Order 4

Îor/Ioc dB 2.5

or

cI

E Pilot dB -7

or

cI

E Sync dB -16

or

cI

EPaging dB -12

or

cI

E FCH dB -16

or

cI

E PDCCH0 dB -16

or

cI

E PDCH dB -7.9

Ioc dBm/1.23

MHz -54

Data Rate kbps 81.6

t

bN

E PDCH dB 6.4




6

3GPP2 C.S0011-C v2.0

A-181



Data Channel Performance in AWGN 3

Test Data Rate [kbps]

F-PDCH Eb/Nt [dB] PER

8.6 0.3

1 1862.4 8.8 0.1

8.9 0.05

6.5 0.3

2 1545.6 6.6 0.1

6.7 0.05

9.5 0.3

3 2476.8 9.6 0.1

9.7 0.05

14.2 0.3

4 3091.2 14.4 0.1

14.5 0.05

5.3 0.3

5 1248.0 5.5 0.1

5.6 0.05

6.4 0.3

6 1862.4 6.6 0.1

6.7 0.05

5.3 0.3

7 1238.4 5.4 0.1

5.5 0.05

4

3GPP2 C.S0011-C v2.0

A-182





8.0 0.3

8 1545.6 8.1 0.1

8.2 0.05

4.0 0.3

9 931.2 4.2 0.1

4.3 0.05

11.4 0.3

10 1862.4 11.6 0.1

11.7 0.05

11.3 0.3

11 2476.8 11.4 0.1

11.5 0.05

8.4 0.3

12 1545.6 8.5 0.1

8.6 0.05

5.9 0.3

13 1248.0 6.1 0.1

6.2 0.05

5.8 0.3

14 1238.4 6.0 0.1

6.1 0.05

3

3GPP2 C.S0011-C v2.0

A-183





7.1 0.3

15 1248.0 7.3 0.1

7.4 0.05

6.8 0.3

16 1238.4 6.9 0.1

7.0 0.05

13.1 0.3

17 2476.8 13.3 0.1

13.4 0.05

8.9 0.3

18 1545.6 9.0 0.1

9.1 0.05

3.3 0.3

19 624.0 3.5 0.1

3.6 0.05

2.6 0.3

20 465.6 2.7 0.1

2.8 0.05

4.4 0.3

21 931.2 4.6 0.1

4.7 0.05

3

3GPP2 C.S0011-C v2.0

A-184





12.1 0.3

22 1862.4 12.3 0.1

12.4 0.05

3.2 0.3

23 619.2 3.3 0.1

3.4 0.05

2.4 0.3

24 326.4 2.7 0.1

2.9 0.05

2.4 0.3

25 316.8 2.6 0.1

2.7 0.05

3.5 0.3

26 633.6 3.7 0.1

3.8 0.05

7.5 0.3

27 1248.0 7.7 0.1

7.8 0.05

7.2 0.3

28 1238.4 7.3 0.1

7.4 0.05

3

3GPP2 C.S0011-C v2.0

A-185





3.9 0.3

29 772.8 4.0 0.1

4.1 0.05

11.1 0.3

30 1545.6 11.2 0.1

11.3 0.05

9.8 0.3

31 1862.4 10.0 0.1

10.1 0.05

8.1 0.3

32 1248.0 8.3 0.1

8.4 0.05

5.1 0.3

33 931.2 5.2 0.1

5.3 0.05

7.8 0.3

34 1238.4 8.0 0.1

8.1 0.05

11.6 0.3

35 1545.6 11.8 0.1

11.9 0.05

3

3GPP2 C.S0011-C v2.0

A-186





10.5 0.3

36 1862.4 10.7 0.1

10.9 0.05

3.5 0.3

37 619.2 3.6 0.1

3.7 0.05

4.5 0.3

38 772.8 4.6 0.1

4.7 0.05

4.0 0.3

39 633.6 4.2 0.1

4.3 0.05

3.9 0.3

40 624.0 4.0 0.1

4.1 0.05

9.5 0.3

41 1248.0 9.7 0.1

9.8 0.05

6.2 0.3

42 931.2 6.4 0.1

6.5 0.05

3

3GPP2 C.S0011-C v2.0

A-187





9.5 0.3

43 1238.4 9.6 0.1

9.7 0.05

12.3 0.3

44 1545.6 12.5 0.1

12.6 0.05

2.6 0.3

45 312.0 2.7 0.1

2.8 0.05

3.1 0.3

46 465.6 3.2 0.1

3.3 0.05

5.0 0.3

47 772.8 5.2 0.1

5.3 0.05

12.8 0.3

48 1545.6 13.0 0.1

13.1 0.05

4.4 0.3

49 633.6 4.7 0.1

4.8 0.05

3

3GPP2 C.S0011-C v2.0

A-188





4.3 0.3

50 624.0 4.5 0.1

4.6 0.05

10.2 0.3

51 1248.0 10.5 0.1

10.6 0.05

7.0 0.3

52 931.2 7.2 0.1

7.3 0.05

4.1 0.3

53 619.2 4.2 0.1

4.3 0.05

10.2 0.3

54 1238.4 10.4 0.1

10.5 0.05

10.4 0.3

55 1545.6 10.5 0.1

10.6 0.05

10.7 0.3

56 1248.0 10.9 0.1

11.1 0.05

3

3GPP2 C.S0011-C v2.0

A-189





10.7 0.3

57 1238.4 10.9 0.1

11.0 0.05

6.2 0.3

58 772.8 6.3 0.1

6.4 0.05

2.9 0.3

59 326.4 3.2 0.1

3.4 0.05

2.4 0.3

60 158.4 2.6 0.1

2.7 0.05

2.9 0.3

61 316.8 3.1 0.1

3.2 0.05

5.2 0.3

62 633.6 5.4 0.1

5.6 0.05

5.0 0.3

63 624.0 5.2 0.1

5.3 0.05

3

3GPP2 C.S0011-C v2.0

A-190





11.3 0.3

64 1248.0 11.5 0.1

11.6 0.05

3.5 0.3

65 465.6 3.7 0.1

3.7 0.05

8.4 0.3

66 931.2 8.6 0.1

8.7 0.05

4.8 0.3

67 619.2 4.9 0.1

5.0 0.05

11.2 0.3

68 1238.4 11.4 0.1

11.5 0.05

6.6 0.3

69 772.8 6.8 0.1

6.9 0.05

5.7 0.3

70 633.6 6.0 0.1

6.1 0.05

3

3GPP2 C.S0011-C v2.0

A-191





5.6 0.3

71 624.0 5.8 0.1

5.9 0.05

8.9 0.3

72 931.2 9.1 0.1

9.2 0.05

5.5 0.3

73 619.2 5.7 0.1

5.8 0.05

6.2 0.3

74 633.6 6.5 0.1

6.7 0.05

3.1 0.3

75 312.0 3.3 0.1

3.4 0.05

6.1 0.3

76 624.0 6.4 0.1

6.5 0.05

4.2 0.3

77 465.6 4.4 0.1

4.5 0.05

3

3GPP2 C.S0011-C v2.0

A-192





9.5 0.3

78 931.2 9.7 0.1

9.8 0.05

6.0 0.3

79 619.2 6.2 0.1

6.3 0.05

7.8 0.3

80 772.8 8.0 0.1

8.1 0.05

2.6 0.3

81 163.2 2.9 0.1

3.0 0.05

3.5 0.3

82 326.4 3.8 0.1

3.9 0.05

3.4 0.3

83 316.8 3.6 0.1

3.7 0.05

6.9 0.3

84 633.6 7.2 0.1

7.4 0.05

3

3GPP2 C.S0011-C v2.0

A-193





6.9 0.3

85 624.0 7.1 0.1

7.2 0.05

5.0 0.3

86 465.6 5.1 0.1

5.2 0.05

10.3 0.3

87 931.2 10.5 0.1

10.7 0.05

6.6 0.3

88 619.2 6.8 0.1

6.9 0.05

8.5 0.3

89 772.8 8.7 0.1

8.8 0.05

3.9 0.3

90 326.4 4.2 0.1

4.4 0.05

3.8 0.3

91 316.8 4.0 0.1

4.1 0.05

3

3GPP2 C.S0011-C v2.0

A-194





7.6 0.3

92 633.6 7.9 0.1

8.0 0.05

3.7 0.3

93 312.0 3.9 0.1

4.0 0.05

7.5 0.3

94 624.0 7.7 0.1

7.8 0.05

5.5 0.3

95 465.6 5.7 0.1

5.8 0.05

7.2 0.3

96 619.2 7.4 0.1

7.5 0.05

9.3 0.3

97 772.8 9.5 0.1

9.6 0.05

4.5 0.3

98 326.4 4.8 0.1

5.0 0.05

3

3GPP2 C.S0011-C v2.0

A-195





2.7 0.3

99 158.4 3.0 0.1

3.1 0.05

4.3 0.3

100 316.8 4.6 0.1

4.7 0.05

8.5 0.3

101 633.6 8.8 0.1

8.9 0.05

4.2 0.3

102 312.0 4.4 0.1

4.5 0.05

8.4 0.3

103 624.0 8.6 0.1

8.7 0.05

6.6 0.3

104 465.6 6.8 0.1

6.9 0.05

8.1 0.3

105 619.2 8.3 0.1

8.4 0.05

3

3GPP2 C.S0011-C v2.0

A-196





3.1 0.3

106 163.2 3.4 0.1

3.5 0.05

5.3 0.3

107 326.4 5.6 0.1

5.8 0.05

5.1 0.3

108 316.8 5.4 0.1

5.5 0.05

5.0 0.3

109 312.0 5.2 0.1

5.3 0.05

7.5 0.3

110 465.6 7.7 0.1

7.8 0.05

2.5 0.3

111 81.6 2.9 0.1

3.0 0.05

3.5 0.3

112 163.2 3.8 0.1

3.9 0.05

3

3GPP2 C.S0011-C v2.0

A-197





6.3 0.3

113 326.4 6.7 0.1

6.9 0.05

3.4 0.3

114 158.4 3.6 0.1

3.7 0.05

6.1 0.3

115 316.8 6.4 0.1

6.5 0.05

6.0 0.3

116 312.0 6.2 0.1

6.3 0.05

8.9 0.3

117 465.6 9.1 0.1

9.2 0.05

2.8 0.3

118 81.6 3.1 0.1

3.3 0.05

4.5 0.3

119 163.2 4.8 0.1

5.0 0.05

3

3GPP2 C.S0011-C v2.0

A-198





8.0 0.3

120 326.4 8.4 0.1

8.6 0.05

4.3 0.3

121 158.4 4.6 0.1

4.7 0.05

7.6 0.3

122 316.8 7.9 0.1

8.1 0.05

7.5 0.3

123 312.0 7.7 0.1

7.9 0.05

3.5 0.3

124 81.6 3.8 0.1

4.0 0.05

5.9 0.3

125 163.2 6.3 0.1

6.5 0.05

5.8 0.3

126 158.4 6.1 0.1

6.2 0.05

3





6.0 0.3

127 81.6 6.4 0.1

6.6 0.05

6

3GPP2 C.S0011-C v2.0

A-199

A.2.15 Forward Packet Data Channel Performance Requirements in Multipath Fading 1

Channel with no Power Control 2




Channel in Fading (Part 1 of 6) 6

Parameters Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Test 7 Test 8

Chan. Sim. Config.

6 3

No. of Re-Tx 3 2

Îor/Ioc

[dB]

6.5 8.5 6.5 8.5

Ioc

[dBm/1.23 MHz]

-61 -59

EP size (bits)

408 792 408 792 408 792 408 792

Walsh Ch 4 11 1 2 4 11 1 2

No. of Slots 4

Modulation Order

2 4 2 4

Data Rate

[kbps]

81.6 158.4 81.6 158.4 81.6 158.4 81.6 158.4

Pilot Ec/Ior

[dB]

-7

Sync Ec/Ior

[dB]

-16

Paging Ec/Ior

[dB]

-12

F-FCH Ec/Ior

[dB]

(1): -12.6

(2): -7.7

(3): -8.6

(1): -14.6

(2): -9.8

(3): -10.6

(1): -11.07

(2): -13.47

(3): -16.17

(1): -13.07

(2): -15.07

(3): -17.87

7

3GPP2 C.S0011-C v2.0

A-200



Parameters Test 1 Test 2 Test 3 Test 4 Test 5 Test 6 Test 7 Test 8

F-PDCCH0 Ec/Ior

[dB]

(1): -8.2

(2): -8.6

(3): -8.7

(1): -10.7

(2): -10.7

(3): -10.9

(1): -10.70

(2): -11.50

(3): -14.70

(1): -12.70

(2): -13.70

(3): -16.60

F-PDCH Ec/Ior

[dB]

(1):

-5.4

(2):

-7.1

(3):

-9.9

(1):

-10.2

(2):

-7.3

(3):

-7.1

(1):

-5.3

(2):

-7.0

(3):

-9.7

(1):

-5.8

(2):

-7.2

(3):

-6.9

(1):

-10.4

(2):

-11.8

(3):

-12.9

(1):

-7.5

(2):

-9.0

(3):

-10.0

(1):

-10.0

(2):

-11.4

(3):

-12.4

(1):

-7.2

(2):

-8.6

(3):

-9.6

F-PDCH Eb/Nt

[dB]

(1):

12.9

(2):

11.1

(3):

8.3

(1):

8.1

(2):

8.1

(3):

8.3

(1):

15.0

(2):

13.3

(3):

10.6

(1):

11.6

(2):

10.2

(3):

10.5

(1):

7.9

(2):

6.4

(3):

5.4

(1):

7.9

(2):

6.4

(3):

5.4

(1):

10.3

(2):

8.8

(3):

7.9

(1):

10.2

(2):

8.8

(3):

7.8


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-201



Parameters Test 9 Test 10

Test 11

Test 12

Test 13

Test 14

Test 15

Test 16

Chan. Sim. Config.

1

No. of Re-Tx

1 (1): 2

(2): 1

(3): 1

(1): 2

(2): 2

(3): 1

Îor/Ioc

[dB]

6.5 8.5 10 8.5

Ioc

[dBm/1.23MHz]

-63

EP size (bits)

408 792 408 792 1560 2328 1560 1560

Walsh Ch 4 11 1 2 7 11 5 4

No. of Slots 4

Modulation Order

2 4 2 3 4

Data Rate

[kbps]

81.6 158.4 81.6 158.4 312 465.6 312 312

Pilot Ec/Ior

[dB]

-7

Sync Ec/Ior

[dB]

-16

Paging Ec/Ior

[dB]

-12

F-FCH Ec/Ior

[dB]

(1): -13.6

(2): -14.4

(3): -15.8

(1): -15.3

(2): -15.7

(3): -17.0

(1): -16.5

(2): -16.8

(3): -18.0

(1): -15.3

(2): -15.7

(3): -17.0

F-PDCCH0 Ec/Ior

[dB]

(1): -16.5

(2): -16.6

(3): -16.6

(1): -18.1

(2): -18.1

(3): -18.2

(1): -19.4

(2): -19.6

(3): -19.6

(1): -18.1

(2): -18.1

(3): -18.2

3GPP2 C.S0011-C v2.0

A-202



Parameters Test 9 Test 10

Test 11

Test 12

Test 13

Test 14

Test 15

Test 16

F-PDCH Ec/Ior

[dB]

(1):

-7.7

(2):

-9.0

(3):

-10.3

(1):

-4.8

(2):

-6.1

(3):

-7.5

(1):

-7.1

(2):

-8.2

(3):

-9.1

(1):

-4.3

(2):

-5.4

(3):

-6.5

(1):

-4.1

(2):

-4.9

(3):

-5.9

(1):

-4.6

(2):

-3.1

(3):

-4.0

(1):

-4.7

(2):

-2.9

(3):

-4.1

(1):

-4.2

(2):

-5.3

(3):

-3.5

F-PDCH Eb/Nt

[dB]

(1):

5.5

(2):

4.2

(3):

2.9

(1):

5.5

(2):

4.2

(3):

2.8

(1):

6.6

(2):

5.5

(3):

4.6

(1):

6.5

(2):

5.4

(3):

4.4

(1):

4.1

(2):

3.3

(3):

2.3

(1):

1.8

(2):

3.3

(3):

2.4

(1):

3.1

(2):

5.0

(3):

3.8

(1):

3.7

(2):

2.6

(3):

4.4


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-203



Parameters Test 17

Test 18

Test 19

Test 20

Test 21

Test 22

Test 23

Chan. Sim. Config.

4

No. of Re-Tx

1

Îor/Ioc

[dB]

6.5 8.5 10 8.5

Ioc

[dBm/1.23MHz]

-57

EP size (bits)

408 792 408 792 1560 2328 1560

Walsh Ch 4 11 1 2 7 11 5

No. of Slots 4

Modulation Order

2 4 2 3

Data Rate

[kbps]

81.6 158.4 81.6 158.4 312 465.6 312

Pilot Ec/Ior

[dB]

-7

Sync Ec/Ior

[dB]

-16

Paging Ec/Ior

[dB]

-12

F-FCH Ec/Ior

[dB]

(1): -16.9

(2): -17.2

(3): -17.3

(1): -17.8

(2): -17.9

(3): -17.8

(1): -18.2

(2): -18.2

(3): -18.2

(1): -17.8

(2): -17.9

(3): -17.8

3

3GPP2 C.S0011-C v2.0

A-204



Parameters Test 17

Test 18

Test 19

Test 20

Test 21

Test 22

Test 23

F-PDCCH0 Ec/Ior

[dB]

(1): -18.8

(2): -19.0

(3): -19.5

(1): -19.8

(2): -19.8

(3): -20.0

(1): -20.4

(2): -20.5

(3): -20.5

(1): -19.8

(2): -19.8

(3): -20.0

F-PDCH Ec/Ior

[dB]

(1):

-11.2

(2):

-11.5

(3):

-11.7

(1):

-8.3

(2):

-8.7

(3):

-9.0

(1):

-9.7

(2):

-10.1

(3):

-10.0

(1):

-7.0

(2):

-7.4

(3):

-7.3

(1):

-6.2

(2):

-6.6

(3):

-6.7

(1):

-4.4

(2):

-4.8

(3):

-4.9

(1):

-4.7

(2):

-5.1

(3):

-5.2

F-PDCH Eb/Nt

[dB]

(1):

1.3

(2):

0.9

(3):

0.7

(1):

1.3

(2):

0.9

(3):

0.6

(1):

3.2

(2):

2.8

(3):

2.9

(1):

3.0

(2):

2.6

(3):

2.7

(1):

1.1

(2):

0.7

(3):

0.6

(1):

1.1

(2):

0.8

(3):

0.7

(1):

2.3

(2):

2.0

(3):

1.8


3


Deleted: BC 0, 2, 3, 7, 9, 10 and 12


3GPP2 C.S0011-C v2.0

A-205



Data Channel in Fading (Part 1 of 3) 3

Traffic Eb/Nt (dB)

Test

Data Rate

(kbps) Band Class 5 and 11

Band Class 0, 2, 3, 7, 9, 10 and 12

Band Class 1, 4, 6 and

8

PER

9.7 8.2 5.9 0.03

12.9 11.1 8.3 0.01

1

81.6

14.6 13.0 9.9 0.005

5.5 NS NS 0.10

8.1 6.7 NS 0.05

9.7 8.1 5.9 0.03

NS 11.0 8.3 0.01

2

158.4

NS NS 9.8 0.005

11.7 10.4 8.1 0.03

15.0 13.3 10.6 0.01

3

81.6

16.6 15.2 12.2 0.005

9.7 8.8 NS 0.05

11.6 10.2 8.0 0.03

14.9 13.2 10.5 0.01

4

158.4

NS NS 12.0 0.005

5.9 4.8 4.1 0.03

7.9 6.4 5.4 0.01

5

81.6

9.2 7.4 6.1 0.005

5.8 4.8 4.1 0.03

7.9 6.4 5.4 0.01

6

158.4

9.1 7.3 6.1 0.005

8.2 7.3 6.6 0.03

10.3 8.8 7.9 0.01

7

81.6

11.6 9.9 8.7 0.005

8.2 7.3 6.5 0.03

10.2 8.8 7.8 0.01

8

158.4

11.5 9.7 8.6 0.005

3GPP2 C.S0011-C v2.0

A-206



Traffic Eb/Nt (dB)

Test

Data Rate


Band Class 0, 2, 3, 7, 9, 10 and 12


8

PER

3.5 2.8 1.9 0.03

5.5 4.2 2.9 0.01

9

81.6

6.7 5 3.6 0.005

3.5 2.7 1.8 0.03

5.5 4.2 2.8 0.01

10

158.4

6.6 5.0 3.5 0.005

4.7 4.2 3.5 0.03

6.6 5.5 4.6 0.01

11

81.6

7.7 6.4 5.2 0.005

4.6 4.1 3.4 0.03

6.5 5.4 4.4 0.01

12

158.4

7.6 6.1 5.0 0.005

2.4 2.0 1.4 0.03

4.1 3.3 2.3 0.01

13

312.0

5.2 4.0 2.8 0.005

0.5 2.1 1.5 0.03

1.8 3.3 2.4 0.01

14

465.6

2.7 4.1 3.0 0.005

1.6 3.6 2.8 0.03

3.1 5.0 3.8 0.01

15

312.0

4.1 5.8 4.4 0.005

2.2 1.5 3.4 0.03

3.7 2.6 4.4 0.01

16

312.0

4.7 3.3 5.0 0.005

0.8 0.5 0.4 0.03

1.3 0.9 0.7 0.01

17

81.6

1.6 1.2 0.9 0.005

3

3GPP2 C.S0011-C v2.0

A-207



Traffic Eb/Nt (dB)

Test

Data Rate


Band Class 0, 2, 3, 7, 9, 10 and 12


8

PER

0.7 0.4 0.3 0.03

1.3 0.9 0.6 0.01

18

158.4

1.6 1.1 0.8 0.005

2.6 2.4 2.5 0.03

3.2 2.8 2.9 0.01

19

81.6

3.4 3.0 3.1 0.005

2.5 2.2 2.3 0.03

3.0 2.6 2.7 0.01

20

158.4

3.4 2.9 2.9 0.005

0.6 0.4 0.4 0.03

1.1 0.7 0.6 0.01

21

312.0

1.3 0.8 0.7 0.005

0.7 0.5 0.4 0.03

1.1 0.8 0.7 0.01

22

465.6

1.4 1 0.8 0.005

1.9 1.6 1.5 0.03

2.3 2.0 1.8 0.01

23

312.0

2.7 2.2 2.0 0.005

3

Page 4-63: [1] Deleted Raqibul Mostafa 11/15/2005 9:46:00 PM


Emission Limit

885-958 MHz, except 887-889 MHz 893-901 MHz 915-925 MHz

More stringent of -60 dBc / 30 kHz and 2.5μW (-26 dBm) / 30 kHz;

25μW (-16 dBm) / 30 kHz; Pout ≤ 30 dBm

< 885 MHz and

> 958 MHz

-16 dBm / 1 MHz; Pout ≤ 44 dBm

More stringent of -60 dBc / 1 MHz and -13 dBm / 1 MHz; Pout > 44 dBm

The lower and upper limits of the frequency measurement are currently 10 MHz and 3 GHz in Japan radio measurement documents.

Documents

Recommended Minimum Performance Standards for … · 3GPP2 C.S0011-C v2.0 CONTENTS v 1 3.4.4 Decision of Power Control Bit for Channels Belonging to Different Power 2 Control Sets