Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
OWNER’S MANUAL
Read this manual carefully before operating this vehicle.
MTT850D
B0S-F8199-30
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
EAU46091
EAU46091
EAU46091
Baca buku panduan dengan teliti sebelum mengendalikan motosikal ini. Buku panduan diberi bersama denganpembelian motosikal.
Introduction
EAU10103
Welcome to the Yamaha world of motorcycling!As the owner of the MTT850D, you are benefiting from Yamaha’s vast experience and newest technology regarding thedesign and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.Please take the time to read this manual thoroughly, so as to enjoy all advantages of your MTT850D. The Owner’s Manualdoes not only instruct you in how to operate, inspect and maintain your motorcycle, but also in how to safeguard yourselfand others from trouble and injury.In addition, the many tips given in this manual will help keep your motorcycle in the best possible condition. If you have anyfurther questions, do not hesitate to contact your Yamaha dealer.The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-rent product information available at the time of printing, there may be minor discrepancies between your motorcycle andthis manual. If there is any question concerning this manual, please consult a Yamaha dealer.
WARNING
EWA10032
Please read this manual carefully and completely before operating this motorcycle.
Important manual information
EAU10134
Particularly important information is distinguished in this manual by the following notations:
*Product and specifications are subject to change without notice.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
A NOTICE indicates special precautions that must be taken to avoid damage to the vehicle or other property.
A TIP provides key information to make procedures easier or clearer.
WARNING
NOTICE
TIP
Important manual information
EAU10201
MTT850DOWNER’S MANUAL
©2018 by Yamaha Motor Co., Ltd.1st edition, December 2018
All rights reserved.Any reprinting or unauthorized use without the written permission of
Yamaha Motor Co., Ltd. is expressly prohibited.
Printed in Malaysia.
Safety information............................ 1-1
Description ....................................... 2-1Left view ......................................... 2-1Right view....................................... 2-2Controls and instruments ............... 2-3
Instrument and control functions... 3-1Immobilizer system......................... 3-1Main switch/steering lock............... 3-2Handlebar switches........................ 3-3Indicator lights and warning
lights............................................ 3-5Cruise control system..................... 3-8Display.......................................... 3-11MENU screen ............................... 3-15D-mode (drive mode).................... 3-25Clutch lever .................................. 3-25Shift pedal .................................... 3-26Quick shift system........................ 3-26Brake lever.................................... 3-26Brake pedal .................................. 3-27ABS .............................................. 3-27Traction control system................ 3-28Fuel tank cap................................ 3-30Fuel............................................... 3-31Fuel tank overflow hose ............... 3-33Catalytic converter ....................... 3-33Seats ............................................ 3-34Adjusting the rider seat height...... 3-35Helmet holder ............................... 3-37
Storage compartment ...................3-38Windshield ...................................3-38Adjusting the headlight beams .....3-38Handlebar position .......................3-39Adjusting the front fork .................3-39Adjusting the shock absorber
assembly....................................3-41Auxiliary DC jack ...........................3-43Auxiliary DC connector .................3-44Sidestand ......................................3-44Ignition circuit cut-off system .......3-45
For your safety – pre-operation
checks ...............................................4-1
Operation and important riding
points .................................................5-1Starting the engine..........................5-1Shifting ............................................5-2Tips for reducing fuel
consumption................................5-3Engine break-in ...............................5-3Parking ............................................5-4
Periodic maintenance and
adjustment ........................................6-1Tool kit ............................................6-2Periodic maintenance charts ..........6-3Periodic maintenance chart for the
emission control system..............6-3
General maintenance and lubrication chart .......................... 6-5
Removing and installing the panel............................................ 6-9
Checking the spark plugs............. 6-10Canister ........................................ 6-11Engine oil ...................................... 6-11Coolant ......................................... 6-13Air filter element............................ 6-15Checking the engine idling
speed ........................................ 6-15Checking the throttle grip free
play............................................ 6-15Valve clearance............................. 6-16Tires .............................................. 6-16Cast wheels .................................. 6-18Adjusting the clutch lever free
play............................................ 6-19Checking the brake lever free
play............................................ 6-19Brake light switches ..................... 6-20Checking the front and rear
brake pads ................................ 6-20Checking the brake fluid level ...... 6-21Changing the brake fluid .............. 6-22Drive chain slack........................... 6-23Cleaning and lubricating the
drive chain................................. 6-24Checking and lubricating the
cables........................................ 6-25
Table of contents
Table of contents
Checking and lubricating the throttle grip and cable................6-25
Checking and lubricating the brake and shift pedals ...............6-26
Checking and lubricating the brake and clutch levers..............6-26
Checking and lubricating the centerstand and sidestand ........6-27
Lubricating the swingarm pivots ...6-28Checking the front fork..................6-28Checking the steering ...................6-29Checking the wheel bearings ........6-29Battery ...........................................6-29Replacing the fuses.......................6-31Headlights .....................................6-33Auxiliary lights ...............................6-33Brake/tail light ...............................6-33Replacing a turn signal light
bulb ............................................6-34Replacing the license plate light
bulb ............................................6-34Troubleshooting ............................6-35Troubleshooting charts .................6-36
Motorcycle care and storage ..........7-1Matte color caution .........................7-1Care.................................................7-1Storage............................................7-4
Specifications ................................... 8-1
Consumer information..................... 9-1Identification numbers .................... 9-1Diagnostic connector...................... 9-2Vehicle data recording.................... 9-2
1-1
1
Safety information
EAU1028C
Be a Responsible Owner
As the vehicle’s owner, you are re-sponsible for the safe and proper oper-ation of your motorcycle.Motorcycles are single-track vehicles.Their safe use and operation are de-pendent upon the use of proper ridingtechniques as well as the expertise ofthe operator. Every operator shouldknow the following requirements be-fore riding this motorcycle.He or she should:
Obtain thorough instructions froma competent source on all aspectsof motorcycle operation.Observe the warnings and mainte-nance requirements in this Own-er’s Manual.Obtain qualified training in safeand proper riding techniques.Obtain professional technical ser-vice as indicated in this Owner’sManual and/or when made neces-sary by mechanical conditions.
Never operate a motorcycle with-out proper training or instruction.Take a training course. Beginnersshould receive training from a cer-tified instructor. Contact an autho-rized motorcycle dealer to find outabout the training courses nearestyou.
Safe Riding
Perform the pre-operation checkseach time you use the vehicle to makesure it is in safe operating condition.Failure to inspect or maintain the vehi-cle properly increases the possibility ofan accident or equipment damage.See page 4-1 for a list of pre-operationchecks.
This motorcycle is designed tocarry the operator and a passen-ger.The failure of motorists to detectand recognize motorcycles in traf-fic is the predominating cause ofautomobile/motorcycle accidents.Many accidents have beencaused by an automobile driver
who did not see the motorcycle.Making yourself conspicuous ap-pears to be very effective in reduc-ing the chance of this type ofaccident.Therefore:
Wear a brightly colored jacket.Use extra caution when you areapproaching and passingthrough intersections, since in-tersections are the most likelyplaces for motorcycle accidentsto occur.Ride where other motorists cansee you. Avoid riding in anothermotorist’s blind spot.Never maintain a motorcyclewithout proper knowledge.Contact an authorized motorcy-cle dealer to inform you on ba-sic motorcycle maintenance.Certain maintenance can onlybe carried out by certified staff.
Safety information
1-2
1Many accidents involve inexperi-enced operators. In fact, many op-erators who have been involved inaccidents do not even have a cur-rent motorcycle license.
Make sure that you are qualifiedand that you only lend your mo-torcycle to other qualified oper-ators.Know your skills and limits.Staying within your limits mayhelp you to avoid an accident.We recommend that you prac-tice riding your motorcyclewhere there is no traffic until youhave become thoroughly famil-iar with the motorcycle and all ofits controls.
Many accidents have beencaused by error of the motorcycleoperator. A typical error made bythe operator is veering wide on aturn due to excessive speed or un-dercornering (insufficient lean an-gle for the speed).
Always obey the speed limit andnever travel faster than warrant-
ed by road and traffic condi-tions.Always signal before turning orchanging lanes. Make sure thatother motorists can see you.
The posture of the operator andpassenger is important for propercontrol.
The operator should keep bothhands on the handlebar andboth feet on the operator foot-rests during operation to main-tain control of the motorcycle.The passenger should alwayshold onto the operator, the seatstrap or grab bar, if equipped,with both hands and keep bothfeet on the passenger footrests.Never carry a passenger unlesshe or she can firmly place bothfeet on the passenger footrests.
Never ride under the influence ofalcohol or other drugs.This motorcycle is designed foron-road use only. It is not suitablefor off-road use.
Protective Apparel
The majority of fatalities from motorcy-cle accidents are the result of head in-juries. The use of a safety helmet is thesingle most critical factor in the pre-vention or reduction of head injuries.
Always wear an approved helmet.Wear a face shield or goggles.Wind in your unprotected eyescould contribute to an impairmentof vision that could delay seeing ahazard.The use of a jacket, heavy boots,trousers, gloves, etc., is effectivein preventing or reducing abra-sions or lacerations.Never wear loose-fitting clothes,otherwise they could catch on thecontrol levers, footrests, or wheelsand cause injury or an accident.Always wear protective clothingthat covers your legs, ankles, andfeet. The engine or exhaust sys-tem become very hot during or af-ter operation and can causeburns.A passenger should also observethe above precautions.
Safety information
1-3
1Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbonmonoxide, a deadly gas. Breathingcarbon monoxide can cause head-aches, dizziness, drowsiness, nausea,confusion, and eventually death.Carbon Monoxide is a colorless, odor-less, tasteless gas which may be pres-ent even if you do not see or smell anyengine exhaust. Deadly levels of car-bon monoxide can collect rapidly andyou can quickly be overcome and un-able to save yourself. Also, deadly lev-els of carbon monoxide can linger forhours or days in enclosed or poorlyventilated areas. If you experience anysymptoms of carbon monoxide poi-soning, leave the area immediately, getfresh air, and SEEK MEDICAL TREAT-MENT.
Do not run engine indoors. Even ifyou try to ventilate engine exhaustwith fans or open windows anddoors, carbon monoxide can rap-idly reach dangerous levels.Do not run engine in poorly venti-lated or partially enclosed areassuch as barns, garages, or car-
ports.
Do not run engine outdoors whereengine exhaust can be drawn intoa building through openings suchas windows and doors.
Loading
Adding accessories or cargo to yourmotorcycle can adversely affect stabil-ity and handling if the weight distribu-tion of the motorcycle is changed. Toavoid the possibility of an accident, useextreme caution when adding cargo oraccessories to your motorcycle. Useextra care when riding a motorcyclethat has added cargo or accessories.Here, along with the information aboutaccessories below, are some generalguidelines to follow if loading cargo toyour motorcycle:The total weight of the operator, pas-senger, accessories and cargo mustnot exceed the maximum load limit.Operation of an overloaded vehicle
could cause an accident.
When loading within this weight limit,keep the following in mind:
Cargo and accessory weightshould be kept as low and close tothe motorcycle as possible. Se-curely pack your heaviest items asclose to the center of the vehicleas possible and make sure to dis-tribute the weight as evenly aspossible on both sides of the mo-torcycle to minimize imbalance orinstability.Shifting weights can create a sud-den imbalance. Make sure thataccessories and cargo are se-curely attached to the motorcyclebefore riding. Check accessorymounts and cargo restraints fre-quently.
Properly adjust the suspensionfor your load (suspension-ad-justable models only), andcheck the condition and pres-sure of your tires.Never attach any large or heavyitems to the handlebar, frontfork, or front fender. Theseitems, including such cargo as
Maximum load:
179 kg (395 lb)
Safety information
1-4
1tents, can create unstable han-dling or a slow steering re-sponse.
This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicleis an important decision. GenuineYamaha accessories, which are avail-able only from a Yamaha dealer, havebeen designed, tested, and approvedby Yamaha for use on your vehicle.Many companies with no connectionto Yamaha manufacture parts and ac-cessories or offer other modificationsfor Yamaha vehicles. Yamaha is not ina position to test the products thatthese aftermarket companies produce.Therefore, Yamaha can neither en-dorse nor recommend the use of ac-cessories not sold by Yamaha ormodifications not specifically recom-mended by Yamaha, even if sold andinstalled by a Yamaha dealer.
Aftermarket Parts, Accessories, and
Modifications
While you may find aftermarket prod-ucts similar in design and quality togenuine Yamaha accessories, recog-nize that some aftermarket accesso-ries or modifications are not suitablebecause of potential safety hazards toyou or others. Installing aftermarketproducts or having other modificationsperformed to your vehicle that changeany of the vehicle’s design or operationcharacteristics can put you and othersat greater risk of serious injury ordeath. You are responsible for injuriesrelated to changes in the vehicle.Keep the following guidelines in mind,as well as those provided under “Load-ing” when mounting accessories.
Never install accessories or carrycargo that would impair the per-formance of your motorcycle.Carefully inspect the accessorybefore using it to make sure that itdoes not in any way reduceground clearance or corneringclearance, limit suspension travel,
steering travel or control opera-tion, or obscure lights or reflec-tors.
Accessories fitted to the han-dlebar or the front fork area cancreate instability due to improp-er weight distribution or aerody-namic changes. If accessoriesare added to the handlebar orfront fork area, they must be aslightweight as possible andshould be kept to a minimum.Bulky or large accessories mayseriously affect the stability ofthe motorcycle due to aerody-namic effects. Wind may at-tempt to lift the motorcycle, orthe motorcycle may becomeunstable in cross winds. Theseaccessories may also cause in-stability when passing or beingpassed by large vehicles.Certain accessories can dis-place the operator from his orher normal riding position. Thisimproper position limits thefreedom of movement of the
sleeping bags, duffel bags, or
Safety information
1-5
1operator and may limit controlability, therefore, such accesso-ries are not recommended.
Use caution when adding electri-cal accessories. If electrical ac-cessories exceed the capacity ofthe motorcycle’s electrical sys-tem, an electric failure could re-sult, which could cause adangerous loss of lights or enginepower.
Aftermarket Tires and Rims
The tires and rims that came with yourmotorcycle were designed to matchthe performance capabilities and toprovide the best combination of han-dling, braking, and comfort. Othertires, rims, sizes, and combinationsmay not be appropriate. See page 6-16for tire specifications and for informa-tion on servicing and replacing yourtires.
Transporting the Motorcycle
Be sure to observe following instruc-tions before transporting the motorcy-cle in another vehicle.
Remove all loose items from themotorcycle.Check that the fuel cock (ifequipped) is in the off position andthat there are no fuel leaks.Shift the transmission into gear(for models with a manual trans-mission).Secure the motorcycle with tie-downs or suitable straps that areattached to solid parts of the mo-torcycle, such as the frame or up-per front fork triple clamp (and not,for example, to rubber-mountedhandlebars or turn signals, orparts that could break). Choosethe location for the straps carefullyso the straps will not rub againstpainted surfaces during transport.The suspension should be com-pressed somewhat by the tie-downs, if possible, so that the mo-torcycle will not bounce exces-sively during transport.
Description
2-1
2
EAU10411
Left view
1 2 3 4,5
61011 8 791. Windshield (page 3-38)2. Battery (page 6-29)3. Fuses (page 6-31)4. Storage compartment (page 3-38)5. Tool kit (page 6-2)6. Seat lock (page 3-34)7. Spring preload adjuster (page 3-41)
8. Rebound damping force adjuster (page 3-41)
9. Shift pedal (page 3-26)10.Engine oil drain bolt (page 6-11)
11.Engine oil filter cartridge (page 6-11)
Description
2-2
2
EAU10421
Right view
1 2 3,4,5 6 7
8910111. Rear brake fluid reservoir (page 6-21)2. Fuel tank cap (page 3-30)3. Rebound damping force adjuster (page 3-39)4. Spring preload adjuster (page 3-39)5. Compression damping force adjuster (page 3-39)6. Headlight (page 6-33)7. Fuses (page 6-31)
8. Coolant reservoir (page 6-13)9. Engine oil level check window (page 6-11)10.Engine oil filler cap (page 6-11)11.Brake pedal (page 3-27)
Description
2-3
2
EAU10431
Controls and instruments
1 2 7
8,99 10
653 4
1. Clutch lever (page 3-25)2. Left handlebar switches (page 3-3)3. Auxiliary DC jack (page 3-43)4. Instrument panel (page 3-5, 3-11)5. Front brake fluid reservoir (page 6-21)6. Right handlebar switches (page 3-3)7. Brake lever (page 3-26)
8. Throttle grip (page 6-15)
9. Grip warmer (page 3-14)10.Main switch/steering lock (page 3-2)
Instrument and control functions
3-1
3
EAU10979
Immobilizer system
This vehicle is equipped with an immo-bilizer system to help prevent theft byre-registering codes in the standardkeys. This system consists of the fol-lowing:
a code re-registering keytwo standard keysa transponder (in each key)an immobilizer unit (on the vehicle)an ECU (on the vehicle)a system indicator light (page 3-7)
About the keys
The key with the red bow is used toregister codes in each standard key.Store the code re-registering key in asafe place. When necessary, take thevehicle along with all three keys to aYamaha dealer to have them re-regis-tered.Do not use the key with the red bow fordriving. It should only be used for re-registering the standard keys. Alwaysuse a standard key for driving.
TIP
Keep the standard keys as well askeys of other immobilizer systemsaway from the code re-registeringkey.Keep other immobilizer systemkeys away from the main switchas they may cause signal interfer-ence.
NOTICEECA11823
DO NOT LOSE THE CODE RE-REG-
ISTERING KEY! CONTACT YOUR
DEALER IMMEDIATELY IF IT IS
LOST! If the code re-registering key
is lost, the existing standard keys
can still be used to start the vehicle.
However, registering a new stan-
dard key is impossible. If all keys
have been lost or damaged, the en-
tire immobilizer system must be re-
placed. Therefore, handle the keys
carefully.
Do not submerse in water.
Do not expose to high tempera-
tures.
Do not place near magnets.
Do not place near items that
transmit electrical signals.
Do not handle roughly.
Do not grind or alter.
Do not disassemble.
Do not put two keys of any im-
mobilizer system on the same
key ring.
1. Code re-registering key (red bow)2. Standard keys (black bow)
Instrument and control functions
3-2
3
EAU10474
Main switch/steering lock
The main switch/steering lock controlsthe ignition and lighting systems, and isused to lock the steering. The variouspositions are described below.
TIP
Be sure to use the standard key (blackbow) for regular use of the vehicle. Tominimize the risk of losing the code re-registering key (red bow), keep it in asafe place and only use it for code re-registering.
EAU84031
ON
All electrical circuits are supplied withpower and the vehicle lights are turnedon. The engine can be started. The keycannot be removed.
TIP
The headlight(s) will turn on whenthe engine is started.To prevent battery drain, do notleave the key in the on positionwithout the engine running.
EAU10662
OFF
All electrical systems are off. The keycan be removed.
WARNING
EWA10062
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
EAU1068B
LOCK
The steering is locked and all electricalsystems are off. The key can be re-moved.
To lock the steering
1. Turn the handlebars all the way tothe left.
2. With the key in the “OFF” position,push the key in and turn it to“LOCK”.
3. Remove the key.
P
ONOFF
LOCK
1. Push.2. Turn.
1 2
Instrument and control functions
3-3
3
TIP
If the steering will not lock, try turningthe handlebars back to the right slight-ly.
To unlock the steering
From the “LOCK” position, push thekey in and turn it to “OFF”.
EAU59680
(Parking)
The hazard lights and turn signal lightscan be turned on, but all other electri-cal systems are off. The key can be re-moved.The steering must be locked before thekey can be turned to “ ”.
NOTICEECA20760
Using the hazard or turn signal lights
for an extended length of time may
cause the battery to discharge.
EAU66055
Handlebar switches
Left
1 2
1. Drive mode switch “MODE”2. TCS switch “ / ”3. Cruise control switches4. Hazard switch “ ”5. Horn switch “ ”6. Turn signal switch “ / ”7. Dimmer/Pass switch “ / /PASS”
2
3
45
1
7
6
1. Push.2. Turn.
Instrument and control functions
3-4
3
Right
EAU73921
Dimmer/Pass switch “ / /PASS”
Set this switch to “ ” for the highbeam and to “ ” for the low beam.To flash the high beam, push the passside “PASS” of the switch while theheadlights are on low beam.
EAU66040
Turn signal switch “ / ”
To signal a right-hand turn, push thisswitch to “ ”. To signal a left-handturn, push this switch to “ ”. Whenreleased, the switch returns to the cen-ter position. To cancel the turn signallights, push the switch in after it has re-turned to the center position.
EAU66030
Horn switch “ ”
Press this switch to sound the horn.
EAU84240
TCS switch “ / ”
See page 3-28 for an explanation ofthe traction control system.
EAU66060
Stop/Run/Start switch “ / / ”
To crank the engine with the starter,set this switch to “ ”, and then pushthe switch down towards “ ”. Seepage 5-1 for starting instructions priorto starting the engine.Set this switch to “ ” to stop the en-gine in case of an emergency, such aswhen the vehicle overturns or when thethrottle cable is stuck.
EAU66010
Hazard switch “ ”
With the key in the “ON” or “ ” posi-tion, use this switch to turn on the haz-ard lights (simultaneous flashing of allturn signal lights).The hazard lights are used in case of anemergency or to warn other driverswhen your vehicle is stopped where itmight be a traffic hazard.
NOTICEECA10062
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-
tery may discharge.
EAU84250
Cruise control switches
See page 3-8 for an explanation of thecruise control system.
EAU84260
Drive mode switch “MODE”
See page 3-25 for an explanation ofthe drive mode.
EAU84271
Wheel switch “ ”
When the display is set to the mainscreen, use the wheel switch to scrolland reset the information display itemsand to set the grip warmers.When the display has been changed tothe MENU screen, use the wheelswitch to navigate the setting modulesand make setting changes.Operate the wheel switch as follows.Rotate up - rotate the wheel upward toscroll up or increase a setting value.
1. Stop/Run/Start switch “ / / ”2. Wheel switch “ ”
1
2
Instrument and control functions
3-5
3
Rotate down - rotate the wheel down-ward to scroll down or decrease a set-ting value.Short push - briefly press the switchinward to make and confirm selec-tions.Long push - press the switch inwardfor one second to reset an informationdisplay item or to access and exit theMENU screen.
TIP
The MENU screen can be ac-cessed by long pushing the wheelswitch except when the gripwarmer display is selected or thefuel tripmeter (F-TRIP) is dis-played.See page 3-11 for more informa-tion on the main screen and itsfunctions.See page 3-15 for more informa-tion on the MENU screen and howto make setting changes.
EAU4939F
Indicator lights and warning
lights
EAU11032
Turn signal indicator lights “ ”
and “ ”
Each indicator light will flash when itscorresponding turn signal lights areflashing.
EAU11061
Neutral indicator light “ ”
This indicator light comes on when thetransmission is in the neutral position.
EAU11081
High beam indicator light “ ”
This indicator light comes on when thehigh beam of the headlight is switchedon.
EAU58402
Cruise control indicator lights “ ”
and “SET”
These indicator lights come on whenthe cruise control system is activated.(See page 3-8.)
TIP
When the vehicle is turned on, theselights should come on for a few sec-onds and then go off. If the lights donot come on, have a Yamaha dealercheck the vehicle.
EAU79310
Engine trouble warning light “ ”
This warning light comes on if a prob-lem is detected in the engine. If this oc-curs, have a Yamaha dealer check theon-board diagnostic system.
1. Traction control system indicator light “ ”2. Engine oil and Coolant warning light “ ”3. Cruise control indicator lights “ ” “SET”4. Shift indicator light5. High beam indicator light “ ”6. ABS warning light “ ”7. Engine trouble warning light “ ”8. Right turn signal indicator light “ ”9. Left turn signal indicator light “ ”10.Neutral indicator light “ ”11.Immobilizer system indicator light “ ”
9 810 7 611
1 3 4 52
ABS
Instrument and control functions
3-6
3
The electrical circuit of the warninglight can be checked by turning the ve-hicle power on. The warning lightshould come on for a few seconds,and then go off.If the warning light does not come on atall, or if the warning light remains on,have a Yamaha dealer check the vehi-cle.
EAU69891
ABS warning light “ ”
In normal operation, this warning lightcomes on when the key is turned to“ON”, and goes off after traveling at aspeed of 10 km/h (6 mi/h) or higher.If the ABS warning light:
does not come on when the key isturned to “ON”comes on or flashes while ridingdoes not go off after traveling at aspeed of 10 km/h (6 mi/h) or high-er
The ABS may not work correctly. If anyof the above occurs, have a Yamahadealer check the system as soon aspossible. (See page 3-27 for an expla-nation of the ABS.)
WARNING
EWA16041
If the ABS warning light does not go
off after traveling at a speed of 10
km/h (6 mi/h) or higher, or if the
warning light comes on or flashes
while riding, the brake system re-
verts to conventional braking. If ei-
ther of the above occurs, or if the
warning light does not come on at
all, use extra caution to avoid possi-
ble wheel lock during emergency
braking. Have a Yamaha dealer
check the brake system and electri-
cal circuits as soon as possible.
EAU73272
Traction control system indicator
light “ ”
In normal operation, this indicator lightis off. When traction control has en-gaged, this indicator light will flash fora few seconds and then go off.When the traction control system isturned off, this indicator light will comeon.If the traction control system becomes
disabled while riding, or if a problem isdetected in the traction control system,this indicator light and the engine trou-ble warning light will come on. (Seepage 3-28 for an explanation of thetraction control system.)
EAU67432
Shift indicator light
This indicator light comes on when it istime to shift to the next higher gear.The engine speeds at which it comeson or goes off can be adjusted. (Seepage 3-18.)As a self-check, the light will come onbriefly when the vehicle is first poweredon.
ABS
1. Traction control system indicator light “ ”2. Engine trouble warning light “ ”
1 2
Instrument and control functions
3-7
3
EAU73120
Immobilizer system indicator
light “ ”
When the key is turned to “OFF” and30 seconds have passed, the indicatorlight will flash steadily to indicate theimmobilizer system is enabled. After 24hours have passed, the indicator lightwill stop flashing, however the immobi-lizer system is still enabled.The electrical circuit of the indicatorlight can be checked by turning the keyto “ON”. The indicator light shouldcome on for a few seconds, and thengo off.If the indicator light does not come oninitially when the key is turned to “ON”,if the indicator light remains on, or if theindicator light flashes in a pattern (if aproblem is detected in the immobilizersystem, the immobilizer system indica-tor light will flash in a pattern), have aYamaha dealer check the vehicle.
TIP
If the immobilizer system indicator lightflashes in the pattern, slowly 5 timesthen quickly 2 times, this could becaused by transponder interference. Ifthis occurs, try the following.
1. Make sure there are no other im-mobilizer keys close to the mainswitch. Other immobilizer systemkeys may cause signal interfer-ence and prevent the engine fromstarting.
2. Use the code re-registering key tostart the engine.
3. If the engine starts, turn it off, andtry starting the engine with thestandard keys.
4. If one or both of the standard keysdo not start the engine, take thevehicle and all 3 keys to a Yamahadealer to have the standard keysre-registered.
EAU84281
Engine oil and Coolant warning
light “ ”
This warning light comes on if the en-gine oil level is low or if the coolanttemperature is high. If this occurs, stopthe engine immediately.When the vehicle is turned on, thewarning light should come on for a fewseconds, and then go off. If the warn-ing light does not come on, have aYamaha dealer check the vehicle.
NOTICEECA26391
If the engine oil and coolant warning
light comes on while the engine is
running, stop the vehicle and engine
immediately.
If the engine is overheating, the
coolant temperature warning
icon will come on. Let the en-
gine cool. Check the coolant
level (see page 6-37).
If the engine oil level is low, the
engine oil warning icon will
come on. Check the oil level
(see page 6-11).
Instrument and control functions
3-8
3
If the warning light remains on
after letting the engine cool and
confirming the proper oil level,
have a Yamaha dealer check
the vehicle. Do not continue to
operate the vehicle!
EAU84290
Cruise control systemThis model is equipped with a cruisecontrol system designed to maintain aset cruising speed.The cruise control system operatesonly when riding in 4th, 5th or 6th gearat speeds between about 50 km/h (31mi/h) and 160 km/h (100 mi/h).
WARNING
EWA16341
Improper use of the cruise con-
trol system may result in loss of
control, which could lead to an
accident. Do not activate the
cruise control system in heavy
traffic, poor weather conditions,
or among winding, slippery,
hilly, rough or gravel roads.
When traveling uphill or down-
hill, the cruise control system
may not be able to maintain the
set cruising speed.
To prevent accidentally activat-
ing the cruise control system,
turn it off when not in use. Make
sure that the cruise control sys-
tem indicator light “ ” is off.
1. Cruise control setting indicator light “SET”2. Cruise control system indicator light “ ”
1. Cruise control setting switch “RES+/SET–”2. Cruise control power switch “ ”
1 2
12
Instrument and control functions
3-9
3
Activating and setting the cruise
control system
1. Push the cruise control powerswitch “ ” located on the lefthandlebar. The cruise control sys-tem indicator light “ ” will comeon.
2. Push the “SET–” side of the cruisecontrol setting switch to activatethe cruise control system. Yourcurrent traveling speed will be-come the set cruising speed. Thecruise control setting indicatorlight “SET” will come on.
Adjusting the set cruising speed
While the cruise control system is op-erating, push the “RES+” side of thecruise control setting switch to in-crease the set cruising speed or the“SET–” side to decrease the set speed.
TIP
Pushing the setting switch once willchange the speed in increments of ap-proximately 2.0 km/h (1.2 mi/h). Hold-ing the “RES+” or “SET–” side of thecruise control setting switch down willincrease or decrease the speed contin-uously until the switch is released.
You can also manually increase yourtraveling speed using the throttle. Afteryou have accelerated, you can set anew cruising speed by pushing the“SET–” side of the setting switch. If youdo not set a new cruising speed, whenyou return the throttle grip, the vehiclewill decelerate to the previously setcruising speed.
Deactivating the cruise control sys-
tem
Perform one of the following opera-tions to cancel the set cruising speed.The “SET” indicator light will go off.
Turn the throttle grip past theclosed position in the decelerationdirection.1. Cruise control power switch “ ”
2. Cruise control system indicator light “ ”
2
11. Cruise control setting switch “RES+/SET–”2. Cruise control setting indicator light “SET”
2
1
1. Deceleration direction
1
Instrument and control functions
3-10
3
Apply the front or rear brake.Disengage the clutch.
Push the power switch to turn off thecruise control system. The “ ” indica-tor light and the “SET” indicator lightwill go off.
TIP
Traveling speed decreases as soon asthe cruise control system is deactivat-ed; unless the throttle grip is turned.
Using the resume function
Push the “RES+” side of the cruisecontrol setting switch to reactivate thecruise control system. The travelingspeed will return to the previously setcruising speed. The “SET” indicatorlight will come on.
WARNING
EWA16351
It is dangerous to use the resume
function when the previously set
cruising speed is too high for current
conditions.
TIP
Pushing the power switch while thesystem is operating will turn the sys-tem off completely and erase the previ-ously set cruising speed. You will notbe able to use the resume function untila new cruising speed has been set.
Automatic deactivation of the cruisecontrol systemThe cruise control system for this mod-el is electronically controlled and islinked with the other control systems.The cruise control system will auto-matically become deactivated underthe following conditions:
The cruise control system is notable to maintain the set cruisingspeed.Wheel slip or wheel spin is detect-ed. (If the traction control systemhas not been turned off, the trac-tion control system will work.)The start/engine stop switch is setto the “ ” position.The engine stalls.The sidestand is lowered.
When traveling with a set cruisingspeed, if the cruise control system isdeactivated under the above condi-tions, the “ ” indicator light will go offand the “SET” indicator light will flashfor 4 seconds, and then go off.When not traveling with a set cruisingspeed, if the start/engine stop switch isset to the “ ” position, the enginestalls, or the sidestand is lowered, thenthe “ ” indicator light will go off (the“SET” indicator light will not flash).If the cruise control system is automat-ically deactivated, please stop andconfirm that your vehicle is in good op-erating condition.Before using the cruise control systemagain, activate it using the powerswitch.
TIP
In some cases, the cruise control sys-tem may not be able to maintain the setcruising speed when the vehicle istraveling uphill or downhill.
When the vehicle is traveling up-hill, the actual traveling speed maybecome lower than the set cruis-
Instrument and control functions
3-11
3
ing speed. If this occurs, acceler-ate to the desired traveling speedusing the throttle.When the vehicle is travelingdownhill, the actual travelingspeed may become higher thanthe set cruising speed. If this oc-curs, the setting switch cannot beused to adjust the set cruisingspeed. To reduce the travelingspeed, apply the brakes. Whenthe brakes are applied, the cruisecontrol system will become deac-tivated.
EAU84301
DisplayThe following items can be found onthe display.
SpeedometerTachometerFuel meterInformation displayTransmission gear displayDrive mode displayTCS displayAir temperature displayGrip warmer displayQS indicatorClockRevolution peak hold indicatorEco indicatorFuel level warning iconEngine oil warning iconCoolant temperature warning icon
TIP
This model uses a thin-film-transistorliquid-crystal display (TFT LCD) forgood contrast and readability in vari-ous lighting conditions. However, dueto the nature of this technology, it is
normal for a small number of pixels tobe inactive.
1. Tachometer2. QS indicator3. Speedometer4. Revolution peak hold indicator5. Clock6. Fuel meter7. Eco indicator “ECO”8. Grip warmer display9. Air temperature display10.Transmission gear display11.TCS display12.Drive mode display13.Information display
km
TRIP-2
TRIP-1
1234.51234.5
km 1 N 2
km/h
1000 r/min
QS 12:00
E
ECO
F
2/1
MODE-STD TCS 1 In °C 25
71013 891112
1 642 53
Instrument and control functions
3-12
3
WARNING
EWA18210
Stop the vehicle before making any
setting changes. Changing settings
while riding can distract the opera-
tor and increase the risk of an acci-
dent.
Speedometer
The speedometer shows the vehicle’straveling speed.
TIP
The display can be set to miles or kilo-meters. Use the “Unit” module on theMENU screen.
Tachometer
The tachometer shows the enginespeed, as measured by the rotationalvelocity of the crankshaft, in revolu-tions per minute (r/min). When the ve-hicle is first powered on, thetachometer will sweep across the r/minrange and then return to zero.
TIP
The tachometer can be color-adjustedand has a revolution peak hold indica-tor which can be turned on or off.
NOTICEECA10032
Do not operate the engine in the ta-
chometer red zone.
Red zone: 11250 r/min and above
Fuel meter
The fuel meter indicates the amount offuel in the fuel tank. The display seg-ments of the fuel meter disappear from“F” (full) towards “E” (empty) as the fuellevel decreases.When the last segment starts flashingand the fuel level warning icon comeson, refuel as soon as possible.
TIP
If all the fuel meter display segmentsflash repeatedly, have a Yamaha deal-er check the related circuits.
Clock
The clock uses a 12-hour time system.
Information display
This section of the main screen is usedto show additional riding related infor-mation such as air and coolant temper-ature readings, tripmeters, and fuelconsumption statistics. The informa-tion display items can be set into fourgroups via the MENU screen.The information display items are:A.TEMP: air temperatureC.TEMP: coolant temperatureTRIP-1: tripmeter 1TRIP-2: tripmeter 2F-TRIP: fuel tripmeterODO: odometerFUEL CON: the amount of fuel con-sumedFUEL AVG: average fuel consumptionCRNT FUEL: current fuel consumption
TIP
ODO will lock at 999999.TRIP-1 and TRIP-2 will reset andcontinue counting after 9999.9has been reached.
Instrument and control functions
3-13
3
When the fuel tank reserve levelhas been reached, F-TRIP ap-pears automatically and beginsrecording distance traveled fromthat point.After refueling and traveling somedistance, F-TRIP will automaticallydisappear.See “Unit” on page 3-16 tochange the fuel consumptionunits, set the clock, and switchbetween miles and kilometers,etc.
TRIP-1, TRIP-2, F-TRIP, FUEL CON,and FUEL AVG items can be individu-ally reset.
To reset information display items1. Use the wheel switch to scroll
through the display items until theitem you want to reset appears.
2. Short push the wheel switch andthe item will flash for five seconds.If both items are resettable items,the top item will flash first. Scrolldown to select the bottom item.
3. While the item is flashing, pressand hold the wheel switch for onesecond.
Transmission gear display
This shows which gear the transmis-sion is in. This model has 6 gears and aneutral position. The neutral position isindicated by the neutral indicatorlight “ ” and by the transmission geardisplay “ ”.
Revolution peak hold indicator
This small bar momentarily appearswithin the tachometer to mark the mostrecent peak r/min speed of the engine.
TIP
The indicator comes on momentarilyonly if the peak engine speed is 7000r/min or higher.
QS indicator
When the key is turned to “ON”, thequick shift system (page 3-26) turns onand this indicator comes on.
TIP
If a problem is detected in the quickshift system, this indicator will turn offand the quick shift system will be un-available. Have a Yamaha dealer checkthe vehicle.
Eco indicator
This indicator comes on when the vehi-cle is being operated in an environ-mentally friendly, fuel-efficient manner.The indicator goes off when the vehicleis stopped.
TIP
Consider the following tips to reducefuel consumption:
Avoid high engine speeds duringacceleration.Travel at a constant speed.Select the transmission gear thatis appropriate for the vehiclespeed.
Drive mode display
This display indicates which drivemode has been selected: “STD”, “A” or“B”. (See page 3-25.)
Instrument and control functions
3-14
3
TCS display
This display indicates which tractioncontrol system setting has been se-lected: “1”, “2” or “OFF”. (See page3-28.)
Air temperature display
This display indicates the air tempera-ture from –9 °C to 50 °C in 1 °C incre-ments.
TIP
–9 °C will be displayed even if theair temperature falls below –9 °C.50 °C will be displayed even if theambient temperature climbsabove 50 °C.The temperature displayed mayvary from the actual ambient tem-perature.
Grip warmer display
The grip warmers can be used whenthe engine is running. There are 4 gripwarmer settings.
To change the grip warmer setting1. Select the grip warmer display.2. Short push the wheel switch, and
then rotate the wheel switch up ordown to change the setting whilethe display is flashing. Short pushthe wheel switch to confirm thesetting.
TIP
Each grip warmer setting can be finetuned in “Grip Warmer Setting” (seepage 3-23).
NOTICEECA17932
Be sure to wear gloves when
using the grip warmers.
Do not use the grip warmers in
warm weather.
If the handlebar grip or throttle
grip becomes worn or dam-
aged, stop using the grip warm-
ers and replace the grips.
Coolant temperature warning “ ”
This icon comes on if the coolant tem-perature reaches 117 °C or higher.Stop the vehicle and turn off the en-gine. Allow the engine to cool.
NOTICEECA10022
Do not continue to operate the en-
gine if it is overheating.
Display Setting
Off
Low
Middle
High
1. Coolant temperature warning “ ”2. Engine oil warning “ ”3. Fuel level warning “ ”
1000 r/min
QS 12:00
2 31
Warning icons
Instrument and control functions
3-15
3
Engine oil warning “ ”
This icon comes on when the engine oillevel is low. Stop the vehicle and cor-rect the engine oil level.When the vehicle is turned on, this iconwill come on for a few seconds, andthen go off.If a malfunction is detected, the oil levelwarning icon will flash repeatedly.Have a Yamaha dealer check the vehi-cle.
NOTICEECA26400
Do not continue to operate the en-
gine if the oil level is low.
Fuel level warning “ ”
This icon comes on when approxi-mately 2.6 L (0.69 US gal, 0.57 Imp.gal)of fuel remains in the tank.If a malfunction is detected, the fuellevel warning icon will flash repeatedly.Have a Yamaha dealer check the vehi-cle.
EAU84311MENU screen
The MENU screen contains the follow-ing setting modules. Select a moduleto make related setting changes. Al-though some settings can be changedor reset via the main screen, the MENUscreen offers access to all display andcontrol settings.
MENU access and operation
The following wheel switch operationsare common operations for accessing,selecting, and moving within theMENU screen and its modules.Long push - press and hold the wheelswitch for one second to access theMENU screen or exit MENU entirely.Select - rotate the wheel switch up ordown to highlight the desired moduleor setting item and then short push thewheel switch (briefly press the wheelswitch inward) to confirm the selection.Triangle mark - certain settingscreens have an upward pointing trian-gle mark item. Select the triangle markto exit that screen and move back onescreen (or long push the wheel switchto exit MENU entirely).
Module Description
View and reset three main-tenance item intervals.Set fuel consumption units.
Set background color.
Turn the shift indicator on/off and adjust tachom-eter settings.Set the multi-function dis-play window items.
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
MaintenanceMaintenance
Maintenance
Unit
Wallpaper
Shift Indicator
Display Setting
Set the low, middle, and high settings to 10 tem-perature levels.
Adjust the clock.
Return all settings to fac-tory default settings.
Grip WarmerSetting
Clock
All Reset
Adjust screen brightness.Brightness
Instrument and control functions
3-16
3
TIP
The MENU screen can be ac-cessed by long pushing the wheelswitch, except when the gripwarmer display is selected or thefuel tripmeter (F-TRIP) is dis-played.Should vehicle motion be detect-ed, the screen will automaticallyexit MENU and change to themain screen.
“Maintenance”
This module allows you to record dis-tance traveled between engine oilchanges (use the OIL item), and for twoother items of your choice (use INTER-VAL 1 and INTERVAL 2).
To reset a maintenance item1. From the MENU screen, select
“Maintenance”.
2. Select the item you want to reset.
3. Long push the wheel switch to re-set the item.
TIP
Maintenance item names cannot bechanged.
“Unit”
This module allows you to switch thedisplay between kilometers and miles.When using kilometers, the fuel con-sumption units can be changed be-tween km/L or L/100km. When usingmiles, MPG will be available.
To set the distance or fuel consump-tion units
1. From the MENU screen, select“Unit”.
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
MaintenanceMaintenance
INTERVAL 2
OIL
INTERVAL 1 123456 km
123456 km
123456 km
Maintenancekm/h GPS 12:00
INTERVAL 2
OIL
INTERVAL 1
0 km
123456 km
123456 km
Maintenancekm/h GPS 12:00
Instrument and control functions
3-17
3
2. Select the distance or consump-tion unit item you want to adjust.
TIP
When “km” is selected, “km/L” or“L/100km” can be set as the fuel con-sumption units. To set the fuel con-sumption units, proceed as follows. If“mile” is selected, skip step 3.
3. Select the units you want to use.
4. Select the triangle symbol to exit.
“Wallpaper”
This module allows you to set the mainscreen background color to black orwhite for both the day and night set-tings. A photo sensor equipped in theinstrument panel detects lighting con-ditions and will automatically changethe display between its day and nightsettings. The photo sensor also con-trols a subtle automatic brightness ad-justment function within both the dayand night modes to suit ambient lightconditions.
To set the wallpaper1. From the MENU screen, select
“Wallpaper”.
2. Select the mode you want to ad-just (select DAY for daytime dis-play settings or NIGHT fornighttime display settings).
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
Maintenance
Unit
km/L or L/100km
km or mile km
km/L
Unitkm/h GPS 12:00
km/L or L/100km
km or mile km
km/L
Unitkm/h GPS 12:00
1. Photo sensor
1
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
Maintenance
Wallpaper
Instrument and control functions
3-18
3
3. Select the background color (se-lect BLACK for a black back-ground or WHITE for a whitebackground).
4. Select the triangle symbol to exit.5. To set another background color,
repeat from step 2 or select the tri-angle symbol to exit this module.
“Shift indicator”
The shift indicator module contains thefollowing items.
2. Select “IND Mode”.
3. Select “ON” to have the indicatorlight steadily, “OFF” to turn the in-dicator off, or “Flash” to have theshift indicator flash when the indi-cator start threshold has beenreached.
12:00 Wallpaperkm/h
DAY
NIGHT
STREET MODE (day)
WHITE
Wallpaperkm/h GPS 12:00
BLACK
Display Description
Set the shift indicator pat-tern to “ON”, “Flash”, or “OFF” and adjust at what r/min the indicator will come on and go off.
Adjust the brightness of the shift indicator.
Set the tachometer color display to “ON” or “OFF” and adjust at what r/min the tachometer will be green and orange.Set the tachometer revolu-tion peak hold indicator to “ON” or “OFF”.
Shift INDSetting
Shift INDBrightness
Tach INDSetting
Peak Rev INDSetting
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
Maintenance
Shift Indicator
12:00 Shift Indicatorkm/h
Tach IND Setting
Shift IND Setting
Peak Rev IND Setting
Shift IND Brightness
1000 r/min
12:00
Shift IND Setting
IND Mode
IND Start
IND Stop
ON
6000 r/min
12000 r/min
km/h Shift Indicator
To make setting changes
1. Select “Shift IND Setting”.
Instrument and control functions
3-19
3
4. Select “IND Start”.
5. Rotate the wheel switch to adjustthe r/min at which the shift indica-tor light will come on. “IND Start”operational range is 5000–12800r/min.
6. Select “IND Stop” then rotate thewheel switch to adjust the r/min atwhich the shift indicator will go off.“IND Stop” operational range is5500–13000 r/min.
TIP
The blue area on the tachometer indi-cates the currently set operationalrange of the shift indicator light.
“Shift IND Brightness”
The shift indicator light has six bright-ness levels.
Select “Shift IND Brightness”, then usethe wheel switch to adjust the setting.Short push the wheel switch to confirmthe setting and exit.
“Tach IND Setting”
This module allows you to turn the ta-chometer color display on or off. Whenturned off, the tachometer will displayall r/min levels below the red zone in
1000 r/min
12:00
Shift IND Setting
IND Mode
IND Start
IND Stop
ON
6000 r/min
12000 r/min
km/h Shift Indicator
1000 r/min
12:00
Shift IND Setting
IND Mode
IND Start
IND Stop
ON
7000 r/min
12000 r/min
km/h Shift Indicator
1000 r/min
12:00
Shift IND Setting
IND Mode
IND Start
IND Stop
ON
8000 r/min
13000 r/min
km/h Shift Indicator 12:00 Shift Indicatorkm/h
Tach IND Setting
Shift IND Setting
Peak Rev IND Setting
Shift IND Brightness
12:00 Shift Indicatorkm/h
Shift IND Brightness
3
Instrument and control functions
3-20
3
black or white (depending on wallpa-per settings). When turned on, the midand mid-to-high r/min zones can beset to come on in green and then or-ange colors.
1. Select “Tach IND Setting”.
2. Select “IND Mode”.
3. Select ON to turn the tachometercolor display mode on (or selectOFF to turn this function off).
4. Select “Tach IND 1st” to set thegreen zone starting r/min.
5. Set the starting r/min by rotatingand then short pushing the wheelswitch. All r/min above this value
up to the “Tach IND 2nd” settingvalue (or the red zone), will be dis-played in green.
TIP
Green bar start setting range: 5000–11300 r/min.
6. Select “Tach IND 2nd”.
12:00 Shift Indicatorkm/h
Tach IND Setting
Shift IND Setting
Peak Rev IND Setting
Shift IND Brightness
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
Instrument and control functions
3-21
3
7. Set the orange color starting r/minby rotating and then short pushingthe wheel switch. All r/min abovethis figure until the red zone, willbe displayed in orange.
TIP
Orange bar start setting range: 5000–11300 r/min.
8. Select the triangle symbol to exit.
“Peak Rev IND Setting”
This module allows you to turn the rev-olution peak hold indicator on or off.
1. Select “Peak Rev IND Setting”.
2. Select “IND Mode” and then se-lect ON (to turn on the indicator) orOFF (to turn off the indicator).
3. Select the triangle symbol to exit.
“Display Setting”
This module allows you to set how theinformation display items (like TRIP-1,ODO, C. TEMP, etc.) are grouped onthe main screen. There are four displaygroups.
To set the display groups1. From the MENU screen, select
“Display Setting”.
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
1000 r/min
12:00 km/h Shift Indicator
Tach IND Setting
IND Mode ON
5000 r/min
8000 r/min
Tach IND 1st
Tach IND 2nd
12:00 Shift Indicatorkm/h
Tach IND Setting
Shift IND Setting
Peak Rev IND Setting
Shift IND Brightness
Peak Rev IND Setting
IND Mode ON
Shift Indicatorkm/h GPS 12:00
1. Information display
km
TRIP-2
TRIP-1
1234.51234.5
km 1 N 2
km/h
1000 r/min
QS 12:00
E
ECO
F
2/1
MODE-STD TCS 1 In °C 25
1
Instrument and control functions
3-22
3
2. DISPLAY-1, DISPLAY-2, DIS-PLAY-3 and DISPLAY-4 are dis-played.
3. For example, let’s select DIS-PLAY-1. 1-1 and 1-2 are dis-played.
4. Select 1-1.
5. Select the desired information dis-play item with the wheel switch.
A.TEMP: air temperatureC.TEMP: coolant tempera-tureTRIP-1: tripmeter 1TRIP-2: tripmeter 2ODO: odometerFUEL CON: the amount offuel consumedFUEL AVG: average fuel con-sumptionCRNT FUEL: current fuel con-sumption
6. Select 1-2 to set the remainingDISPLAY-1 group item.
7. Select the triangle symbol to exit.To set the other display groups,repeat from step 3.
“Brightness”
This module allows you to adjust thegeneral brightness level of the displayscreen.
To set the brightness1. From the MENU screen, select
“Brightness”.
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
Maintenance
Display Setting
DISPLAY-1
1 - 1 A.TEMP
1 - 2 C.TEMP
Display Settingkm/h GPS 12:00
DISPLAY-1
1 - 1 A.TEMP
1 - 2 C.TEMP
Display Settingkm/h GPS 12:00
DISPLAY-1
1 - 1 A.TEMP
1 - 2 C.TEMP
Display Settingkm/h GPS 12:00
Instrument and control functions
3-23
3
2. Select the desired brightness levelby rotating the wheel switch, andthen short push the wheel switchto fix the setting.
“Grip Warmer Setting”
This module allows you to set the low,middle, and high settings to 10 tem-perature levels.
To set the grip warmer temperaturelevels
1. From the MENU screen, select“Grip Warmer Setting”.
2. Select “LO”, “MIDDLE”, or“HIGH”.
3. Set the temperature level.
4. To set the temperature level foranother grip warmer setting, re-peat from step 2 or select the tri-angle symbol to exit this module.
“Clock”
This module allows you to set theclock.
To set the clock1. From the MENU screen, select
“Clock”.
12:00 MENUkm/h
Brightness
Display Setting
Shift Indicator
Wallpaper
Unit
Maintenance
Brightness
12:00 km/h Brightness
2
12:00 MENUkm/h
All Reset
Clock
Grip Warmer Setting
Brightness
Display Setting
Shift Indicator
Grip Warmer Setting
HIGH
LO
MIDDLE Level 5
Level 1
Level 10
km/h GPS 12:00 Grip Warmer Setting
HIGH
LO
MIDDLE
km/h GPS 12:00
Level 5
Level 1
Level 10
Grip Warmer Setting
Instrument and control functions
3-24
3
2. When “Clock” is selected, thehours figure will be highlighted.
3. Set the hour by rotating and thenshort push the wheel switch.
4. The minutes figure will becomehighlighted.
5. Set the minutes figure by rotatingand then short push the wheelswitch.
6. Short push the wheel switch againto exit and go back to the MENUscreen.
“All Reset”
This module contains the all reset func-tion which resets everything, exceptthe odometer and clock, to its factorypreset or default setting.Select YES to reset all items. After se-lecting YES, all items will be reset andthe display will automatically return tothe MENU screen.
12:00 MENUkm/h
All Reset
Clock
Grip Warmer Setting
Brightness
Display Setting
Shift Indicator
Clock
12:00 Clockkm/h
11 34:
12:00 Clockkm/h
12 34:
12:00 Clockkm/h
12 34:
12:00 Clockkm/h
12 58:
Instrument and control functions
3-25
3
EAU84420
D-mode (drive mode)D-mode is an electronically controlledengine performance system with threemode selections: “STD”, “A”, and “B”.Push the drive mode switch “MODE”to switch between modes. (See page3-4.)
TIP
Before using D-mode, make sure youunderstand its operation along with theoperation of the drive mode switch.
Mode “STD”
Mode “STD” is suitable for various rid-ing conditions.
This mode allows the rider to enjoysmooth and sporty drivability from thelow-speed range to the high-speedrange.
Mode “A”
Mode “A” offers a sportier engine re-sponse in the low- to mid-speed rangecompared to mode “STD”.
Mode “B”
Mode “B” offers response that issomewhat less sharp compared tomode “STD” for riding situations thatrequire especially sensitive throttle op-eration.
EAU12822
Clutch lever
The clutch lever is located on the leftside of the handlebar. To disengagethe clutch, pull the lever toward thehandlebar grip. To engage the clutch,release the lever. The lever should bepulled rapidly and released slowly forsmooth clutch operation.The clutch lever is equipped with aclutch switch, which is part of the igni-tion circuit cut-off system. (See page3-45.)
1. Drive mode switch “MODE”
11. Clutch lever
1
Instrument and control functions
3-26
3
EAU84320
Shift pedal
The shift pedal is located on the leftside of the motorcycle and is used incombination with the clutch lever whenshifting the gears of the 6-speed con-stant-mesh transmission.When the quick shift system is turnedon, the shift switch senses shift pedalmovement and allows for upshiftingwithout operating the clutch lever. (Seepage 3-26.)
EAU84330
Quick shift systemThe quick shift system (QS) allows forfull-throttle, clutch lever-less, electron-ically-assisted upshifts. When the shiftswitch detects motion in the shift pedal(page 3-26), engine power and drivetorque are momentarily adjusted to al-low the upshift to occur.
TIP
The quick shift system operateswhen traveling at least 20 km/h (12mi/h) with an engine speed of2300 r/min or higher, and onlywhen accelerating.It does not operate when theclutch lever is pulled.
EAU26826
Brake leverThe brake lever is located on the rightside of the handlebar. To apply thefront brake, pull the lever toward thethrottle grip.
The brake lever is equipped with abrake lever position adjusting dial. Toadjust the distance between the brakelever and the throttle grip, slightly pullthe brake lever away from the throttlegrip and rotate the adjusting dial. Makesure the setting number on the adjust-ing dial aligns with the match mark onthe brake lever.
1. Shift pedal2. Shift switch
1
2
1. Brake lever2. Distance3. Brake lever position adjusting dial4. Match mark
23 4
1
Instrument and control functions
3-27
3
EAU12944
Brake pedal
The brake pedal is located on the rightside of the motorcycle. To apply therear brake, press down on the brakepedal.
EAU63040
ABSThe Yamaha ABS (Anti-lock BrakeSystem) features a dual electronic con-trol system, which acts on the front andrear brakes independently.Operate the brakes with ABS as youwould conventional brakes. If the ABSis activated, a pulsating sensation maybe felt at the brake lever or brake ped-al. In this situation, continue to applythe brakes and let the ABS work; donot “pump” the brakes as this will re-duce braking effectiveness.
WARNING
EWA16051
Always keep a sufficient distance
from the vehicle ahead to match the
riding speed even with ABS.
The ABS performs best with
long braking distances.
On certain surfaces, such as
rough or gravel roads, the brak-
ing distance may be longer with
the ABS than without.
The ABS is monitored by an ECU,which will revert the system to conven-
tional braking if a malfunction occurs.
TIP
The ABS performs a self-diagno-sis test each time the vehicle firststarts off after the key is turned to“ON” and the vehicle has traveledat a speed of 10 km/h (6 mi/h) orhigher. During this test, a “click-ing” noise can be heard from thehydraulic control unit, and if thebrake lever or brake pedal is evenslightly applied, a vibration can befelt at the lever and pedal, butthese do not indicate a malfunc-tion.This ABS has a test mode whichallows the owner to experiencethe pulsation at the brake lever orbrake pedal when the ABS is op-erating. However, special tools arerequired, so please consult yourYamaha dealer.
NOTICEECA20100
Be careful not to damage the wheel
1. Brake pedal
1
Instrument and control functions
3-28
3
EAU84341
Traction control systemThe traction control system (TCS)helps maintain traction when acceler-ating on slippery surfaces, such as un-paved or wet roads. If sensors detectthat the rear wheel is starting to slip(uncontrolled spinning), the tractioncontrol system assists by regulatingengine power as needed until tractionis restored.
WARNING
EWA15433
The traction control system is not a
substitute for riding appropriately
for the conditions. Traction control
cannot prevent loss of traction due
to excessive speed when entering
turns, when accelerating hard at a
sharp lean angle, or while braking,
and cannot prevent front wheel slip-
ping. As with any vehicle, approach
surfaces that may be slippery with
caution and avoid especially slip-
pery surfaces.
The “ ” indicator light flashes whentraction control has engaged. You maynotice slight changes in engine and ex-haust sounds when the system has en-gaged.
1. Front wheel sensor2. Front wheel sensor rotor
1. Rear wheel sensor2. Rear wheel sensor rotor
1
2
1
2
1. TCS switch “ / ”
1. Traction control system indicator light “ ”2. TCS display
1
km
TRIP-2
TRIP-1
1234.51234.5
km 1 N 2
km/h
1000 r/min
QS 12:00
E
ECO
F
2/1
MODE-STD TCS 1 In °C 25
1 2
sensor or wheel sensor rotor; other-
wise, improper performance of the
ABS will result.
Instrument and control functions
3-29
3
When the traction control system hasbeen set to “OFF”, the “ ” indicatorlight will come on.The TCS display indicates the currentTCS setting. There are three settings.
TCS “OFF”
TCS “OFF” turns the traction controlsystem off.
TCS “1”
TCS “1” minimizes traction controlsystem assist.
TCS “2”
TCS “2” maximizes traction control as-sist; wheel spin is most strongly con-trolled.
TIP
When the vehicle is turned on,traction control is turned on andset to “1” or “2” (whichever waslast selected).Turn the traction control systemoff to help free the rear wheel if thevehicle gets stuck in mud, sand, orother soft surfaces.
NOTICEECA16801
Use only the specified tires. (See
page 6-16.) Using different sized
tires will prevent the traction control
system from controlling tire rotation
accurately.
Setting the traction control system
WARNING
EWA15441
Be sure to stop the vehicle before
making any setting changes to the
traction control system. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
TCS settings can be changed onlywhen the vehicle is stopped and thethrottle closed.
Push the TCS switch “ ” tochange the TCS setting to TCS“1” and push the TCS switch “ ”to change the TCS setting to TCS“2”.
Push the TCS switch “ ” for twoseconds to turn the traction con-trol system off.Push the TCS switch “ ” to turntraction control back on (TCS willreturn to the previous setting).
Resetting the traction control sys-
tem
The traction control system will auto-matically disable when:
the front wheel or rear wheelcomes off the ground while riding.excessive rear wheel spin is de-tected while riding.either wheel is rotated with the keyturned to “ON” (such as when per-forming maintenance).
If the traction control system is dis-abled, both the “ ” indicator light andthe “ ” warning light will come on.
Instrument and control functions
3-30
3
Should this occur, try resetting the sys-tem as follows.
1. Stop the vehicle and turn the keyto “OFF”.
2. Wait a few seconds and then turnthe key back to “ON”.
3. The “ ” indicator light shouldturn off and the system be en-abled.
TIP
If the “ ” indicator light remains on af-ter resetting, the vehicle may still beridden; however, have a Yamaha deal-er check the vehicle as soon as possi-ble.
4. Have a Yamaha dealer check thevehicle and turn off the “ ”warning light.
EAU13076
Fuel tank cap
To open the fuel tank cap
Open the fuel tank cap lock cover, in-sert the key into the lock, and then turnit 1/4 turn clockwise. The lock will bereleased and the fuel tank cap can beopened.
To close the fuel tank cap
With the key still inserted in the lock,push down the fuel tank cap. Turn thekey 1/4 turn counterclockwise, removeit, and then close the lock cover.
1. Traction control system indicator light “ ”2. TCS display3. Engine trouble warning light “ ”
km
TRIP-2
TRIP-1
1234.51234.5
km 1 N 2
km/h
1000 r/min
QS 12:00
E
ECO
F
2/1
MODE-STD TCS 1 In °C 25
31 2
1. Fuel tank cap lock cover2. Unlock.
1
2
Instrument and control functions
3-31
3
TIP
The fuel tank cap cannot be closed un-less the key is in the lock. In addition,the key cannot be removed if the cap isnot properly closed and locked.
WARNING
EWA11092
Make sure that the fuel tank cap is
properly closed after filling fuel.
Leaking fuel is a fire hazard.
EAU13222
FuelMake sure there is sufficient gasoline inthe tank.
WARNING
EWA10882
Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the en-gine and be sure that no one is sit-ting on the vehicle. Never refuelwhile smoking, or while in the vi-cinity of sparks, open flames, orother sources of ignition such asthe pilot lights of water heatersand clothes dryers.
2. Do not overfill the fuel tank. Whenrefueling, be sure to insert thepump nozzle into the fuel tank fillerhole. Stop filling when the fuelreaches the bottom of the fillertube. Because fuel expands whenit heats up, heat from the engine or
the sun can cause fuel to spill outof the fuel tank.
3. Wipe up any spilled fuel immedi-ately. NOTICE: Immediately
wipe off spilled fuel with a clean,
dry, soft cloth, since fuel may
deteriorate painted surfaces or
plastic parts. [ECA10072]
4. Be sure to securely close the fueltank cap.
WARNING
EWA15152
Gasoline is poisonous and can
cause injury or death. Handle gaso-
line with care. Never siphon gasoline
1. Fuel tank filler tube2. Maximum fuel level
1 2
Instrument and control functions
3-32
3
ately. If gasoline spills on your skin,
wash with soap and water. If gaso-
line spills on your clothing, change
your clothes.
EAU75300
NOTICEECA11401
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.
TIP
This mark identifies the recom-mended fuel for this vehicle asspecified by European regulation(EN228).Check that gasoline nozzle hasthe same identifier when fueling.
Your Yamaha engine has been de-signed to use premium unleaded gas-oline with a research octane number of95 or higher. If knocking (or pinging)occurs, use a gasoline of a differentbrand. Use of unleaded fuel will extendspark plug life and reduce mainte-nance costs.
Gasohol
There are two types of gasohol: gaso-hol containing ethanol and that con-taining methanol. Gasohol containingethanol can be used if the ethanol con-tent does not exceed 10% (E10). Gas-ohol containing methanol is notrecommended by Yamaha because itcan cause damage to the fuel systemor vehicle performance problems.
Recommended fuel:
Premium unleaded gasoline (Gaso-hol [E10] acceptable)
Fuel tank capacity:
18 L (4.8 US gal, 4.0 Imp.gal)Fuel reserve amount:
2.6 L (0.69 US gal, 0.57 Imp.gal)
E5 E10
by mouth. If you should swallow
some gasoline or inhale a lot of gas-
oline vapor, or get some gasoline in
your eyes, see your doctor immedi-
Instrument and control functions
3-33
3
EAU72972
Fuel tank overflow hose
Before operating the vehicle:Check the overflow hose connec-tion and for damage.Confirm the overflow hose is notblocked and is routed through theclamp.
TIP
See page 6-11 for canister information.
EAU13434
Catalytic converterThis model is equipped with a catalyticconverter in the exhaust system.
WARNING
EWA10863
The exhaust system is hot after op-
eration. To prevent a fire hazard or
burns:
Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.
Make sure that the exhaust sys-
tem has cooled down before
doing any maintenance work.
Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.
NOTICEECA10702
Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.
1. Fuel tank overflow hose2. Clamp
2
1
Instrument and control functions
3-34
3
EAU65800
Seats
Passenger seat
To remove the passenger seat1. Insert the key into the seat lock,
and then turn it counterclockwise.
2. Lift the front of the passenger seatand pull it forward.
To install the passenger seat1. Insert the projections on the rear
of the passenger seat into the seatholders as shown, and then pushthe front of the seat down to lockit in place.
2. Remove the key.
Rider seat
To remove the rider seat1. Remove the passenger seat.2. Remove the cap, then push the
rider seat lock lever, located underthe back of the rider seat, to theleft as shown, and then pull theseat off.
To install the rider seat1. Install the cap with the arrow mark
facing forward.2. Insert the projection on the front of
the rider seat into the seat holderas shown, and then push the rearof the seat down to lock it in place.
1. Seat lock2. Unlock.
1
2
1. Projection2. Seat holder
21
1. Cap2. Rider seat lock lever
2
1
Instrument and control functions
3-35
3
3. Install the passenger seat.
TIP
Make sure that the seats are prop-erly secured before riding.The rider seat height can be ad-justed to change the riding posi-tion. (See the following section.)
EAU63050
Adjusting the rider seat heightThe rider seat height can be adjustedto one of two positions to suit the rid-er’s preference.The rider seat height was adjusted tothe lower position at delivery.
To change the rider seat height to
the high position
1. Remove the passenger seat andrider seat. (See page 3-34.)
2. Remove the rider seat height posi-tion adjuster by pulling it upward.
3. Install the rider seat height posi-tion adjuster by inserting the frontprojections into the grommets.
1. Projection2. Seat holder
2
1
1. Low position2. High position
2 1
1. Rider seat height position adjuster
1. Rider seat height position adjuster2. Projection3. Grommet
1
12
3
3
Instrument and control functions
3-36
3
4. Insert the projection on the front ofthe rider seat into seat holder B asshown.
5. Align the projection on the bottomof the rider seat with the “H” posi-tion slot, and then push the rear ofthe seat down to lock it in place asshown.
6. Install the passenger seat.
To change the rider seat height to
the low position
1. Remove the passenger seat andrider seat. (See page 3-34.)
2. Remove the rider seat height posi-tion adjuster by pulling it upward.
3. Install the rider seat height posi-tion adjuster by inserting the rearprojections into the grommets.
4. Insert the projection on the front ofthe rider seat into seat holder A asshown.
1. Projection2. Seat holder B (for high position)
2
12
1. Projection2. “H” position slot
1 2
1. Rider seat height position adjuster2. Projection3. Grommet
1. Projection2. Seat holder A (for low position)
12
3
3
2
12
Instrument and control functions
3-37
3
5. Align the projection on the bottomof the rider seat with the “L” posi-tion slot, and then push the rear ofthe seat down to lock it in place asshown.
6. Install the passenger seat.
TIP
Make sure that the seats are properlysecured before riding.
EAU63060
Helmet holderThe helmet holder is located under thepassenger seat. A helmet holding ca-ble is provided in the owner’s tool kit tosecure a helmet to the helmet holder.
To secure a helmet to the helmet
holder
1. Remove the passenger seat. (Seepage 3-34.)
2. Pass the helmet holding cablethrough the buckle on the helmetstrap as shown, and then hook thecable loops over the helmet hold-er.
3. Place the helmet on the right sideof the vehicle, and then install theseat. WARNING! Never ride with
a helmet attached to the helmet
holder, since the helmet may hit
objects, causing loss of control
and possibly an accident. [EWA10162]
To release the helmet from the hel-
met holder
Remove the passenger seat, removethe helmet holding cable from the hel-met holder and the helmet, and then in-stall the seat.
1. Projection2. “L” position slot
1 2
1. Helmet2. Helmet holding cable3. Helmet holder
32
1
Instrument and control functions
3-38
3
EAU62550
Storage compartment
The storage compartment is locatedunder the passenger seat. (See page3-34.)When storing documents or otheritems in the storage compartment, besure to wrap them in a plastic bag sothat they will not get wet. When wash-ing the vehicle, be careful not to let anywater enter the storage compartment.
WARNING
EWA15401
Do not exceed the maximum load of
179 kg (395 lb) for the vehicle.
EAU83932
Windshield This model is equipped with an adjust-able windshield.
To change the position of the wind-shield, lift up the windshield lock leverand slide the windshield up or down.Release the lock lever when finished.
TIP
Make sure the windshield and lock le-ver are properly secured before riding.
EAU39612
Adjusting the headlight beamsThe headlight beam adjusting knobsare used to raise or lower the height ofthe headlight beams. It may be neces-sary to adjust the headlight beams toincrease visibility and help preventblinding oncoming drivers when carry-ing more or less load than usual. Obeylocal laws and regulations when ad-justing the headlights.To raise the headlight beams, turn theknobs in direction (a). To lower theheadlight beams, turn the knobs in di-rection (b).
1. Storage compartment
1
1. Windshield lock lever2. Windshield
1
2
1. Headlight beam adjusting knob
(a)
(b)
1
(b)
(a)
1
Instrument and control functions
3-39
3
EAU46833
Handlebar position The handlebar can be adjusted to oneof two positions to suit the rider’s pref-erence. Have a Yamaha dealer adjustthe position of the handlebar.
EAU76342
Adjusting the front fork
WARNING
EWA14671
Always adjust the spring preload on
both fork legs equally, otherwise
poor handling and loss of stability
may result.
Each front fork leg is equipped with aspring preload adjusting bolt, the rightfront fork leg is equipped with a re-bound damping force adjusting screwand the left front fork leg with a com-pression damping force adjustingscrew.
NOTICEECA10102
To avoid damaging the mechanism,
do not attempt to turn beyond the
maximum or minimum settings.
Spring preload
To increase the spring preload andthereby harden the suspension, turnthe adjusting bolt on each fork leg in di-rection (a). To decrease the spring pre-
load and thereby soften thesuspension, turn the adjusting bolt oneach fork leg in direction (b).
The spring preload setting is deter-mined by measuring distance A,shown in the illustration. The shorterdistance A is, the higher the spring pre-load; the longer distance A is, the lowerthe spring preload.
1. Handlebar
1
1. Spring preload adjusting bolt
11
(a) (b) (a) (b)
Instrument and control functions
3-40
3
TIP
Be sure to perform this adjustment onthe right front fork leg.
TIP
When adjusting the damping forcesettings, turn the adjuster in direc-tion (a) until it stops, and thencount the clicks in direction (b).
Although a damping force adjust-er may click beyond the statedminimum settings, such adjust-ments are ineffective and maydamage the suspension.
Compression damping force
The compression damping force is ad-justed on the left front fork leg only.To increase the compression dampingforce and thereby harden the com-pression damping, turn the adjustingscrew in direction (a). To decrease thecompression damping force and there-by soften the compression damping,turn the adjusting screw in direction (b).
TIP
Be sure to perform this adjustment onthe left front fork leg.
1
1. Rebound damping force adjusting screw
Rebound damping setting:Minimum (soft):
11 click(s) in direction (b)Standard:
7 click(s) in direction (b)Maximum (hard):
1 click(s) in direction (b)
1(a) (b)
Rebound damping force
The rebound damping force is adjust-ed on the right front fork leg only.To increase the rebound dampingforce and thereby harden the rebounddamping, turn the adjusting screw indirection (a). To decrease the rebounddamping force and thereby soften therebound damping, turn the adjustingscrew in direction (b).
1. Distance A
Spring preload setting:Minimum (soft):
Distance A = 19.0 mm (0.75 in)Standard:
Distance A = 16.0 mm (0.63 in)Maximum (hard):
Distance A = 4.0 mm (0.16 in)
Instrument and control functions
3-41
3
TIP
When adjusting the damping forcesettings, turn the adjuster in direc-tion (a) until it stops, and thencount the clicks in direction (b).
Although a damping force adjust-er may click beyond the statedminimum settings, such adjust-ments are ineffective and maydamage the suspension.When turning a damping force ad-juster in direction (a), the 0 clickposition and the 1 click positionmay be the same.
EAU84350
Adjusting the shock absorber
assemblyThis shock absorber assembly isequipped with a spring preload adjust-ing knob and a rebound damping forceadjusting screw.
NOTICEECA10102
To avoid damaging the mechanism,
do not attempt to turn beyond the
maximum or minimum settings.
Spring preload
To increase the spring preload andthereby harden the suspension, turnthe adjusting knob in direction (a). Todecrease the spring preload and there-by soften the suspension, turn the ad-justing knob in direction (b).
1. Compression damping force adjusting screw
Compression damping setting:Minimum (soft):
11 click(s) in direction (b)Standard:
7 click(s) in direction (b)Maximum (hard):
1 click(s) in direction (b)
1(a) (b)
Instrument and control functions
3-42
3
TIP
When adjusting the spring preload set-ting, turn the adjuster in direction (b)until it stops, and then count the clicksin direction (a).
Rebound damping force
To increase the rebound dampingforce and thereby harden the rebounddamping, turn the adjusting screw in
direction (a). To decrease the rebounddamping force and thereby soften therebound damping, turn the adjustingscrew in direction (b).
TIP
When adjusting the damping forcesettings, turn the adjuster in direc-tion (a) until it stops, and thencount the clicks in direction (b).
Although a damping force adjust-er may click beyond the statedminimum settings, such adjust-ments are ineffective and maydamage the suspension.
WARNING
EWA10222
This shock absorber assembly con-
tains highly pressurized nitrogen
gas. Read and understand the fol-
lowing information before handling
the shock absorber assembly.
Do not tamper with or attempt
to open the cylinder assembly.
Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.
This may cause the unit to ex-
plode due to excessive gas
pressure.
Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.
1. Spring preload adjusting knob
Spring preload setting:Minimum (soft):
1 clicks in direction (a)Standard:
11 clicks in direction (a)Maximum (hard):
24 clicks in direction (a)
(b)
(a)
1
1. Rebound damping force adjusting screw
Rebound damping setting:Minimum (soft):
18 clicks in direction (b)Standard:
7 clicks in direction (b)Maximum (hard):
1 clicks in direction (b)
1 (a)(b)
Instrument and control functions
3-43
3
Do not dispose of a damaged or
worn-out shock absorber as-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.
EAU49454
Auxiliary DC jack
A 12-V accessory connected to theauxiliary DC jack can be used when themain switch is on.
NOTICEECA15432
The accessory connected to the
auxiliary DC jack should not be used
with the engine turned off, and the
load must never exceed 24 W (2 A),
otherwise the fuse may blow or the
battery may discharge.
To use the auxiliary DC jack
1. Turn the main switch off.
2. Remove the auxiliary DC jack cap.3. Turn the accessory off.4. Insert the accessory plug into the
auxiliary DC jack.
5. Turn the main switch on, and startthe engine. (See page 5-1.)
6. Turn the accessory on.
WARNING
EWA14361
To prevent electrical shock or short-
circuiting, make sure that the cap is
installed when the auxiliary DC jack
is not being used.
1. Auxiliary DC jack cap
1
1. Auxiliary DC jack
1
Instrument and control functions
3-44
3
EAU70641
Auxiliary DC connectorThis vehicle is equipped with an auxil-iary DC connector. Consult yourYamaha dealer before installing anyaccessories.
EAU15306
SidestandThe sidestand is located on the leftside of the frame. Raise the sidestandor lower it with your foot while holdingthe vehicle upright.
TIP
The built-in sidestand switch is part ofthe ignition circuit cut-off system,which cuts the ignition in certain situa-tions. (See the following section for anexplanation of the ignition circuit cut-off system.)
WARNING
EWA10242
The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly and have a
Yamaha dealer repair it if it does not
function properly.
Instrument and control functions
3-45
3
EAU57952
Ignition circuit cut-off systemThis system prevents in-gear enginestarts unless the clutch lever is pulledand the sidestand is up. Also, it willstop the running engine should thesidestand be lowered while the trans-mission is in gear.Periodically check this system via thefollowing procedure.
TIP
This check is most reliable if per-formed with a warmed-up engine.See pages 3-2 and 3-3 for switchoperation information.
Instrument and control functions
3-46
3
With the engine turned off:1. Move the sidestand down.2. Set engine stop switch to run position.3. Turn main switch to on position. 4. Shift transmission into neutral.5. Push the start switch.Does the engine start?
With the engine still running:6. Move the sidestand up.7. Pull the clutch lever.8. Shift transmission into gear.9. Move the sidestand down.Does the engine stall?
After the engine has stalled:10. Move the sidestand up.11. Pull the clutch lever.12. Push the start switch.Does the engine start?
The system is OK. The motorcycle can be ridden.
YES NO
YES NO
YES NO
The neutral switch may not be working.The motorcycle should not be ridden untilchecked by a Yamaha dealer.
The clutch switch may not be working.The motorcycle should not be ridden untilchecked by a Yamaha dealer.
The sidestand switch may not be working.The motorcycle should not be ridden untilchecked by a Yamaha dealer.
If a malfunction is found, have the vehicle inspected before riding.
WARNING
For your safety – pre-operation checks
4-1
4
EAU15599
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspectionand maintenance procedures and schedules described in the Owner’s Manual.
WARNING
EWA11152
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
EGAPSKCEHCMETI
Fuel
Check fuel level in fuel tank.Refuel if necessary.Check fuel line for leakage.Check fuel tank overflow hose for obstructions, cracks or damage, and check hose connection.
3-31, 3-33
Engine oil
Check oil level in engine.If necessary, add recommended oil to specified level.Check vehicle for oil leakage.
6-11
Coolant
Check coolant level in reservoir.If necessary, add recommended coolant to specified level.Check cooling system for leakage.
6-13
Front brake
Check operation.If soft or spongy, have Yamaha dealer bleed hydraulic system.Check brake pads for wear.Replace if necessary.Check fluid level in reservoir.If necessary, add specified brake fluid to specified level.Check hydraulic system for leakage.
6-20, 6-21
For your safety – pre-operation checks
4-2
4
Rear brake
Check operation.If soft or spongy, have Yamaha dealer bleed hydraulic system.Check brake pads for wear.Replace if necessary.Check fluid level in reservoir.If necessary, add specified brake fluid to specified level.Check hydraulic system for leakage.
6-20, 6-21
Clutch
Check operation.Lubricate cable if necessary.Check lever free play.Adjust if necessary.
6-19
Throttle grip
Make sure that operation is smooth.Check throttle grip free play.If necessary, have Yamaha dealer adjust throttle grip free play and lubricate ca-ble and grip housing.
6-15, 6-25
Control cablesMake sure that operation is smooth.Lubricate if necessary. 6-25
Drive chain
Check chain slack.Adjust if necessary.Check chain condition.Lubricate if necessary.
6-23, 6-24
Wheels and tires
Check for damage.Check tire condition and tread depth.Check air pressure.Correct if necessary.
6-16, 6-18
Brake and shift pedalsMake sure that operation is smooth.Lubricate pedal pivoting points if necessary. 6-26
Brake and clutch leversMake sure that operation is smooth.Lubricate lever pivoting points if necessary. 6-26
Centerstand, sidestandMake sure that operation is smooth.Lubricate pivots if necessary. 6-27
EGAPSKCEHCMETI
For your safety – pre-operation checks
4-3
4
Chassis fastenersMake sure that all nuts, bolts and screws are properly tightened.Tighten if necessary. —
Instruments, lights, signals
and switches
Check operation.Correct if necessary. —
Sidestand switch Check operation of ignition circuit cut-off system.If system is not working correctly, have Yamaha dealer check vehicle. 3-44
EGAPSKCEHCMETI
Operation and important riding points
5-1
5
EAU15952
Read the Owner’s Manual carefully tobecome familiar with all controls. Ifthere is a control or function you do notunderstand, ask your Yamaha dealer.
WARNING
EWA10272
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accident
or injury.
EAUM3631
TIP
This model is equipped with:a lean angle sensor to stop the en-gine in case of a turnover. In thiscase, the engine trouble warninglight will come on, but this is not amalfunction. Turn the key to“OFF” and then to “ON” to turn offthe warning light. Failing to do sowill prevent the engine from start-ing even though the engine willcrank when pushing the startswitch.an engine auto-stop system. Theengine stops automatically if leftidling for 20 minutes. If the enginestops, simply push the startswitch to restart the engine.
EAU84361
Starting the engineUnder normal conditions, shift thetransmission into neutral before start-ing the engine. To start the engine withthe transmission in gear, the sidestandmust be up and the clutch lever pulled.
To start the engine1. Turn the main switch to “ON”, and
set the engine stop switch to “ ”.2. Confirm the following lights per-
form a circuit check.Engine trouble warning lightABS warning lightTraction control system indi-cator lightCruise control indicator lightsShift indicator lightEngine oil and Coolant warn-ing lightImmobilizer system indicatorlight
TIP
The ABS warning light should gooff after reaching a speed of 10km/h (6 mi/h) or higher.
Operation and important riding points
5-2
5
The neutral position indicator lightshould be on when the transmis-sion is in neutral.
NOTICEECA24110
If a warning or indicator light does
not work as described above, have a
Yamaha dealer check the vehicle.
3. Shift the transmission into neutral.4. Push the start switch “ ” to crank
the engine with the starter.Release the start switch when theengine starts, or after 5 seconds.Wait 10 seconds before pressingthe switch again to allow batteryvoltage to restore.
NOTICEECA11043
For maximum engine life, never ac-
celerate hard when the engine is
cold!
EAU84370
Shifting
Shifting gears lets you control theamount of engine power available forstarting off, accelerating, climbing hills,etc.The gear positions are shown in the il-lustration.
TIP
To shift the transmission into theneutral position ( ), press theshift pedal down repeatedly until itreaches the end of its travel, andthen slightly raise it.
This model is equipped with aquick shift system. (See page3-26.)
NOTICEECA23990
Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
Except when upshifting with the
quick shift system, always use
the clutch while changing gears
to avoid damaging the engine,
transmission, and drive train,
which are not designed to with-
stand the shock of forced shift-
ing.
1. Gear positions2. Shift pedal
2
1
1N23456
Operation and important riding points
5-3
5
EAU16811
Tips for reducing fuel con-
sumptionFuel consumption depends largely onyour riding style. Consider the follow-ing tips to reduce fuel consumption:
Shift up swiftly, and avoid high en-gine speeds during acceleration.Do not rev the engine while shift-ing down, and avoid high enginespeeds with no load on the en-gine.Turn the engine off instead of let-ting it idle for an extended lengthof time (e.g., in traffic jams, at traf-fic lights or at railroad crossings).
EAU16842
Engine break-inThere is never a more important periodin the life of your engine than the periodbetween 0 and 1600 km (1000 mi). Forthis reason, you should read the fol-lowing material carefully.Since the engine is brand new, do notput an excessive load on it for the first1600 km (1000 mi). The various parts inthe engine wear and polish themselvesto the correct operating clearances.During this period, prolonged full-throt-tle operation or any condition thatmight result in engine overheatingmust be avoided.
EAU17094
0–1000 km (0–600 mi)
Avoid prolonged operation above 5600r/min. NOTICE: After 1000 km (600
mi) of operation, the engine oil must
be changed and the oil filter car-
tridge or element replaced. [ECA10303]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 6800r/min.
1600 km (1000 mi) and beyond
The vehicle can now be operated nor-mally.
NOTICEECA10311
Keep the engine speed out of
the tachometer red zone.
If any engine trouble should oc-
cur during the engine break-in
period, immediately have a
Yamaha dealer check the vehi-
cle.
Operation and important riding points
5-4
5
EAU17214
ParkingWhen parking, stop the engine, andthen remove the key from the mainswitch.
WARNING
EWA10312
Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.
Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
Do not park near grass or other
flammable materials which
might catch fire.
Periodic maintenance and adjustment
6-1
6
EAU17246
Periodic inspection, adjustment, andlubrication will keep your vehicle in thesafest and most efficient conditionpossible. Safety is an obligation of thevehicle owner/operator. The most im-portant points of vehicle inspection,adjustment, and lubrication are ex-plained on the following pages.The intervals given in the periodicmaintenance charts should be simplyconsidered as a general guide undernormal riding conditions. However, de-pending on the weather, terrain, geo-graphical location, and individual use,the maintenance intervals may need tobe shortened.
WARNING
EWA10322
Failure to properly maintain the vehi-
cle or performing maintenance ac-
tivities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle ser-
vice, have a Yamaha dealer perform
service.
WARNING
EWA15123
Turn off the engine when performing
maintenance unless otherwise
specified.
A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Running the engine while ser-
vicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-3 for more in-
formation about carbon monox-
ide.
WARNING
EWA15461
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before
touching them.
EAU17303
Emission controls not only function toensure cleaner air, but are also vital toproper engine operation and maximumperformance. In the following periodicmaintenance charts, the services relat-ed to emissions control are groupedseparately. These services requirespecialized data, knowledge, andequipment. Maintenance, replace-ment, or repair of the emission controldevices and systems may be per-formed by any repair establishment orindividual that is certified (if applicable).Yamaha dealers are trained andequipped to perform these particularservices.
Periodic maintenance and adjustment
6-2
6
EAU59911
Tool kit
The tool kit is located under the pas-senger seat. (See page 3-34.)The information included in this manualand the tools provided in the tool kit areintended to assist you in the perfor-mance of preventive maintenance andminor repairs. However, a torquewrench and other tools are necessaryto perform certain maintenance workcorrectly.
TIP
If you do not have the tools or experi-ence required for a particular job, haveyour Yamaha dealer perform it for you.
1. Tool kit
1
1 1
Periodic maintenance and adjustment
6-3
6
EAU71033
Periodic maintenance charts
TIP
Items marked with an asterisk should be performed by your Yamaha dealer because these items require special tools,data, and technical skills.From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (6000 mi).The annual checks must be performed every year, except if a distance-based maintenance is performed in-
stead.
EAU71051
Periodic maintenance chart for the emission control system
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
1 * Fuel line
Check fuel hoses for cracks or damage.Replace if necessary.
√ √ √ √ √
2 * Spark plugs
Check condition.Adjust gap and clean. √√
Replace. √√
3 * Valve clearance )im 00042( mk 00004 yrevE.tsujda dna kcehC
4 * Fuel injection
Check engine idle speed. √ √ √ √ √ √
Check and adjust synchroniza-tion. √ √ √ √ √
5 * Exhaust system
Check for leakage.Tighten if necessary.Replace gaskets if necessary.
√ √ √ √ √
Periodic maintenance and adjustment
6-4
6
6 * Evaporative emis-
sion control system
Check control system for dam-age.Replace if necessary.
√√
7 * Air induction sys-
tem
Check the air cut-off valve, reed valve, and hose for damage.Replace any damaged parts if necessary.
√ √ √ √ √
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
Periodic maintenance and adjustment
6-5
6
EAU71351General maintenance and lubrication chart
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
1 * Diagnostic system
check
Perform dynamic inspection us-ing Yamaha diagnostic tool.Check the error codes.
√ √ √ √ √ √
2 * Air filter element )im 00042( mk 00004 yrevE.ecalpeR
3 ClutchCheck operation.Adjust. √ √ √ √ √
4 * Front brake
Check operation, fluid level, and for fluid leakage.Replace brake pads if necessary.
√ √ √ √ √ √
5 * Rear brake
Check operation, fluid level, and for fluid leakage.Replace brake pads if necessary.
√ √ √ √ √ √
6 * Brake hosesCheck for cracks or damage. √ √ √ √ √
sraey 4 yrevE.ecalpeR
7 * Brake fluid sraey 2 yrevE.egnahC
8 * WheelsCheck runout and for damage.Replace if necessary. √ √ √ √
9 * Tires
Check tread depth and for dam-age.Replace if necessary.Check air pressure.Correct if necessary.
√ √ √ √ √
10 * Wheel bearingsCheck bearing for looseness or damage. √ √ √ √
Periodic maintenance and adjustment
6-6
6
11 * Swingarm pivot
bearings
Check operation and for exces-sive play. √ √ √ √
Lubricate with lithium-soap-based grease. Every 50000 km (30000 mi)
12 Drive chain
Check chain slack, alignment and condition.Adjust and lubricate chain with a special O-ring chain lubricant thoroughly.
Every 1000 km (600 mi) and after washing the motorcycle, riding in the rain or riding in wet areas
13 * Steering bearings
Check bearing assemblies for looseness.
√√√
Moderately repack with lithium-soap-based grease. √√
14 * Chassis fastenersMake sure that all nuts, bolts and screws are properly tightened. √ √ √ √ √
15Brake lever pivot
shaftLubricate with silicone grease. √ √ √ √ √
16Brake pedal pivot
shaft
Lubricate with lithium-soap-based grease. √ √ √ √ √
17Clutch lever pivot
shaft
Lubricate with lithium-soap-based grease. √ √ √ √ √
18Shift pedal pivot
shaft
Lubricate with lithium-soap-based grease. √ √ √ √ √
19Sidestand, center-
stand
Check operation.Lubricate with lithium-soap-based grease.
√ √ √ √ √
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
Periodic maintenance and adjustment
6-7
6
20 * Sidestand switchCheck operation and replace if necessary. √ √ √ √ √ √
21 * Front fork
Check operation and for oil leak-age.Replace if necessary.
√ √ √ √
22 * Shock absorber as-
sembly
Check operation and for oil leak-age.Replace if necessary.
√ √ √ √
23 *
Rear suspension re-
lay arm and con-
necting arm
pivoting points
Check operation. √ √ √ √
24 Engine oil
Change (warm engine before draining).Check oil level and vehicle for oil leakage.
√ √ √ √ √ √
25Engine oil filter car-
tridgeReplace. √√√
26 * Cooling system
Check coolant level and vehicle for coolant leakage. √ √ √ √ √
sraey 3 yrevE.egnahC
27 * Front and rear
brake switchesCheck operation. √ √ √ √ √ √
28 * Moving parts and
cablesLubricate. √ √ √ √ √
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
Periodic maintenance and adjustment
6-8
6
EAU72800
TIP
Air filterThis model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com-pressed air to avoid damaging it.The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake serviceRegularly check and, if necessary, correct the brake fluid level.Every two years replace the internal components of the brake master cylinders and calipers, and change the brakefluid.Replace the brake hoses every four years and if cracked or damaged.
29 * Throttle grip hous-
ing and cable
Check operation and free play.Adjust the throttle cable free play if necessary.Lubricate the throttle grip hous-ing, cable and grip warmer wire.
√ √ √ √ √
30 * Lights, signals and
switches
Check operation.Adjust headlight beam. √ √ √ √ √ √
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READINGANNUAL
CHECK1000 km
(600 mi)
10000 km
(6000 mi)
20000 km
(12000 mi)
30000 km
(18000 mi)
40000 km
(24000 mi)
Periodic maintenance and adjustment
6-9
6
EAU18752
Removing and installing the
panelThe panel shown needs to be removedto perform some of the maintenancejobs described in this chapter. Refer tothis section each time the panel needsto be removed and installed.
EAU63101
Panel A
To remove the panel1. Remove the quick fastener
screws, and then pull the paneloutward and slide it downward asshown.
2. Disconnect the turn signal lightlead coupler.
To install the panel1. Connect the turn signal light lead
coupler.2. Place the panel in the original po-
sition, and then install the quickfastener screws.
1. Panel A
1
1. Quick fastener screw
1. Panel A2. Quick fastener screw
1
2
1
1. Turn signal light lead coupler
1
Periodic maintenance and adjustment
6-10
6
EAU19653
Checking the spark plugsThe spark plugs are important enginecomponents, which should bechecked periodically, preferably by aYamaha dealer. Since heat and depos-its will cause any spark plug to slowlyerode, they should be removed andchecked in accordance with the peri-odic maintenance and lubricationchart. In addition, the condition of thespark plugs can reveal the condition ofthe engine.The porcelain insulator around thecenter electrode of each spark plugshould be a medium-to-light tan (theideal color when the vehicle is riddennormally), and all spark plugs installedin the engine should have the samecolor. If any spark plug shows a dis-tinctly different color, the engine couldbe operating improperly. Do not at-tempt to diagnose such problemsyourself. Instead, have a Yamaha deal-er check the vehicle.If a spark plug shows signs of elec-trode erosion and excessive carbon orother deposits, it should be replaced.
Before installing a spark plug, thespark plug gap should be measuredwith a wire thickness gauge and, ifnecessary, adjusted to specification.
Clean the surface of the spark pluggasket and its mating surface, andthen wipe off any grime from the sparkplug threads.
TIP
If a torque wrench is not availablewhen installing a spark plug, a goodestimate of the correct torque is 1/4–1/2 turn past finger tight. However, thespark plug should be tightened to thespecified torque as soon as possible.
NOTICEECA10841
Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.
Specified spark plug:NGK/CPR9EA9
1. Spark plug gap
Spark plug gap:0.8–0.9 mm (0.031–0.035 in)
Tightening torque:Spark plug:
13 N·m (1.3 kgf·m, 9.6 lb·ft)
Periodic maintenance and adjustment
6-11
6
EAU36112
Canister
This model is equipped with a canisterto prevent the discharging of fuel vaporinto the atmosphere. Before operatingthis vehicle, make sure to check thefollowing:
Check each hose connection.Check each hose and canister forcracks or damage. Replace ifdamaged.Make sure that the canisterbreather is not blocked, and ifnecessary, clean it.
EAU1990EEngine oilThe engine oil level should be checkedregularly. In addition, the oil must bechanged and the oil filter cartridge re-placed at the intervals specified in theperiodic maintenance chart.
NOTICEECA11621
In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
Make sure that no foreign mate-
rial enters the crankcase.
To check the engine oil level
1. After warming up the engine, waita few minutes for the oil to settle.
2. With the vehicle on a level surface,hold it upright for an accuratereading.
3. Look at the check window locatedat the bottom-right side of thecrankcase.
TIP
The engine oil should be between theminimum and maximum level marks.
1. Canister2. Canister breather
1
2Recommended engine oil:
See page 8-1.Oil quantity:
Oil change:2.40 L (2.54 US qt, 2.11 Imp.qt)
With oil filter removal:2.70 L (2.85 US qt, 2.38 Imp.qt)
1. Engine oil filler cap2. O-ring3. Engine oil level check window4. Maximum level mark5. Minimum level mark
2
1
3
45
Periodic maintenance and adjustment
6-12
6
4. If the engine oil is at or below theminimum level mark, remove theoil filler cap and add oil.
5. Check the engine oil filler cap O-ring. Replace if damaged.
6. Install the engine oil filler cap.
To change the engine oil (and filter)
1. Start the engine and allow it to idlefor a few minutes to warm up theoil, and then stop the engine.
2. Place an oil pan under the engineto collect the used oil.
3. Remove the engine oil filler cap,and then the engine oil drain boltand gasket.
TIP
Skip steps 4–6 if the oil filter cartridgeis not being replaced.
4. Remove the oil filter cartridge withan oil filter wrench.
TIP
An oil filter wrench is available at aYamaha dealer.
5. Apply a thin coat of clean engineoil to the O-ring of the new oil filtercartridge.
TIP
Make sure that the O-ring is properlyseated.
6. Install the new oil filter cartridge,and then tighten to the specifiedtorque.
1. Engine oil filler cap2. O-ring
2
1
1. Engine oil drain bolt2. Gasket
1. Oil filter wrench2. Oil filter cartridge
1 2
21
1. O-ring
Periodic maintenance and adjustment
6-13
6
7. Install the engine oil drain bolt witha new gasket, and then tighten thebolt to the specified torque.
8. Pour the specified amount of therecommended oil into the crank-case.
TIP
Using a funnel is recommended.
9. After checking the engine oil fillercap O-ring, install the filler cap.
TIP
Wipe off any spilled oil before startingthe engine.
10. Start the engine and let it idle whilechecking for oil leaks.
TIP
If any oil leaks are found which youcannot fix, have the vehicle inspected.
11. Stop the engine, wait a few min-utes for the oil to settle, and thencheck the oil level one last time.NOTICE: Do not operate the ve-
hicle until you know that the en-
gine oil level is sufficient. [ECA10012]
EAUS1203
CoolantThe coolant level should be checkedregularly. In addition, the coolant mustbe changed at the intervals specified inthe periodic maintenance chart.
TIP
If genuine Yamaha coolant is not avail-able, use an ethylene glycol antifreezecontaining corrosion inhibitors for alu-minum engines and mix with distilledwater at a 1:1 ratio.
EAU20097
To check the coolant level
Since the coolant level varies with en-gine temperature, check when the en-gine is cold.
1. Park the vehicle on a level surface.
1. Torque wrench
Tightening torque:Oil filter cartridge:
17 N·m (1.7 kgf·m, 13 lb·ft)
Tightening torque:Engine oil drain bolt:
43 N·m (4.3 kgf·m, 32 lb·ft)
1Recommended coolant:
YAMALUBE coolantCoolant quantity:
Coolant reservoir (max level mark):0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes):1.93 L (2.04 US qt, 1.70 Imp.qt)
Periodic maintenance and adjustment
6-14
6
2. With the vehicle in an upright posi-tion, look at the coolant level in thereservoir.
3. If the coolant is at or below theminimum level mark, remove thecoolant reservoir cap. WARNING!
Remove only the coolant reser-
voir cap. Never attempt to re-
move the radiator cap when the
engine is hot. [EWA15162]
4. Add coolant to the maximum levelmark. NOTICE: If coolant is not
available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the cooling system will not
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the anti-
freeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced. [ECA10473]
5. Install the coolant reservoir cap.
EAU33032
Changing the coolant
The coolant must be changed at the in-tervals specified in the periodic main-tenance and lubrication chart. Have aYamaha dealer change the coolant.WARNING! Never attempt to remove
the radiator cap when the engine is
hot. [EWA10382]1. Coolant reservoir2. Maximum level mark3. Minimum level mark
2
1
3
1. Coolant reservoir cap
1
Periodic maintenance and adjustment
6-15
6
EAU36765
Air filter elementThe air filter element must be replacedat the intervals specified in the periodicmaintenance and lubrication chart.Have a Yamaha dealer replace the airfilter element.
EAU44735
Checking the engine idling
speedCheck the engine idling speed and, ifnecessary, have it corrected by aYamaha dealer.
EAU21386
Checking the throttle grip free
playMeasure the throttle grip free play asshown.
Periodically check the throttle grip freeplay and, if necessary, have a Yamahadealer adjust it.
Engine idling speed:1100–1300 r/min
1. Throttle grip free play
Throttle grip free play:3.0–5.0 mm (0.12–0.20 in)
1
Periodic maintenance and adjustment
6-16
6
EAU21403
Valve clearanceThe valves are an important enginecomponent, and since valve clearancechanges with use, they must bechecked and adjusted at the intervalsspecified in the periodic maintenancechart. Unadjusted valves can result inimproper air-fuel mixture, enginenoise, and eventually engine damage.To prevent this from occurring, haveyour Yamaha dealer check and adjustthe valve clearance at regular intervals.
TIP
This service must be performed whenthe engine is cold.
EAU64412
TiresTires are the only contact between thevehicle and the road. Safety in all con-ditions of riding depends on a relativelysmall area of road contact. Therefore, itis essential to maintain the tires in goodcondition at all times and replace themat the appropriate time with the speci-fied tires.
Tire air pressure
The tire air pressure should bechecked and, if necessary, adjustedbefore each ride.
WARNING
EWA10504
Operation of this vehicle with im-
proper tire pressure may cause se-
vere injury or death from loss of
control.
The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.
WARNING
EWA10512
Never overload your vehicle. Opera-
tion of an overloaded vehicle could
cause an accident.
Cold tire air pressure:
1 person:Front:
225 kPa (2.25 kgf/cm², 33 psi)Rear:
250 kPa (2.50 kgf/cm², 36 psi)2 persons:
Front:250 kPa (2.50 kgf/cm², 36 psi)
Rear:290 kPa (2.90 kgf/cm², 42 psi)
Maximum load:Vehicle:
179 kg (395 lb)The vehicle’s maximum load is the combined weight of the rider, pas-senger, cargo, and any accessories.
Periodic maintenance and adjustment
6-17
6
Tire inspection
The tires must be checked before eachride. If the center tread depth reachesthe specified limit, if the tire has a nailor glass fragments in it, or if the side-wall is cracked, have a Yamaha dealerreplace the tire immediately.
TIP
The tire tread depth limits may differfrom country to country. Always com-ply with the local regulations.
WARNING
EWA10472
Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the vehi-
cle with excessively worn tires
decreases riding stability and
can lead to loss of control.
The replacement of all wheel
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience to do so.
Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics.
Tire information
This model is equipped with tubelesstires and tire air valves.Tires age, even if they have not beenused or have only been used occasion-ally. Cracking of the tread and sidewallrubber, sometimes accompanied bycarcass deformation, is an evidence ofageing. Old and aged tires shall bechecked by tire specialists to ascertaintheir suitability for further use.
WARNING
EWA10902
The front and rear tires should
be of the same make and de-
sign, otherwise the handling
1. Tire sidewall2. Tire tread depth
Minimum tire tread depth (front and
rear):1.6 mm (0.06 in)
1. Tire air valve2. Tire air valve core3. Tire air valve cap with seal
Periodic maintenance and adjustment
6-18
6
characteristics of the motorcy-
cle may be different, which
could lead to an accident.
Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.
Use only the tire valves and
valve cores listed below to
avoid tire deflation during a ride.
After extensive tests, only the tires list-ed below have been approved for thismodel by Yamaha.
WARNING
EWA10601
This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.
Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.
Brand-new tires can have a rel-
atively poor grip on certain road
surfaces until they have been
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.
The tires must be warmed up
before a high-speed run.
Always adjust the tire air pres-
sure according to the operating
conditions.
EAU21963
Cast wheelsTo maximize the performance, durabil-ity, and safe operation of your vehicle,note the following points regarding thespecified wheels.
The wheel rims should bechecked for cracks, bends, warp-age or other damage before eachride. If any damage is found, havea Yamaha dealer replace thewheel. Do not attempt even thesmallest repair to the wheel. A de-formed or cracked wheel must bereplaced.The wheel should be balancedwhenever either the tire or wheelhas been changed or replaced. Anunbalanced wheel can result inpoor performance, adverse han-dling characteristics, and a short-ened tire life.
Front tire:Size:
120/70ZR17 M/C (58W)Manufacturer/model:
DUNLOP/D222FRear tire:
Size:180/55ZR17 M/C (73W)
Manufacturer/model:DUNLOP/D222
FRONT and REAR:Tire air valve:
TR412Valve core:
#9100 (original)
Periodic maintenance and adjustment
6-19
6
EAU22083
Adjusting the clutch lever free
playMeasure the clutch lever free play asshown.
Periodically check the clutch lever freeplay and, if necessary, adjust it as fol-lows.To increase the clutch lever free play,turn the clutch lever free play adjustingbolt in direction (a). To decrease theclutch lever free play, turn the adjustingbolt in direction (b).
TIP
If the specified free play cannot be ob-tained as described above or if theclutch does not operate correctly, havea Yamaha dealer check the internalclutch mechanism.
EAU37914
Checking the brake lever free
play
There should be no free play at thebrake lever end. If there is free play,have a Yamaha dealer inspect thebrake system.
WARNING
EWA14212
A soft or spongy feeling in the brake
lever can indicate the presence of
air in the hydraulic system. If there is
air in the hydraulic system, have a
Yamaha dealer bleed the system be-
fore operating the vehicle. Air in the
hydraulic system will diminish the
1. Clutch lever free play adjusting bolt2. Clutch lever free play
Clutch lever free play:5.0–10.0 mm (0.20–0.39 in)
21
(b)
(a)
1. No brake lever free play
1
Periodic maintenance and adjustment
6-20
6
braking performance, which may re-
sult in loss of control and an acci-
dent.
EAU36505
Brake light switchesThe brake light should come on justbefore braking takes effect. The brakelight is activated by switches connect-ed to the brake lever and brake pedal.Since the brake light switches arecomponents of the anti-lock brake sys-tem, they should only be serviced by aYamaha dealer.
EAU22393
Checking the front and rear
brake padsThe front and rear brake pads must bechecked for wear at the intervals spec-ified in the periodic maintenance andlubrication chart.
EAU36891
Front brake pads
Each front brake pad is provided withwear indicators, which allows you tocheck the brake pad wear without hav-ing to disassemble the brake. To checkthe brake pad wear, check the positionof the wear indicators while applyingthe brake. If a brake pad has worn tothe point that a wear indicator almost
1. Brake pad wear indicator
11
Periodic maintenance and adjustment
6-21
6
touches the brake disc, have aYamaha dealer replace the brake padsas a set.
EAU46292
Rear brake pads
Each rear brake pad is provided withwear indicator grooves, which allowyou to check the brake pad wear with-out having to disassemble the brake.To check the brake pad wear, checkthe wear indicator grooves. If a brakepad has worn to the point that a wearindicator groove almost appears, havea Yamaha dealer replace the brakepads as a set.
EAU40262
Checking the brake fluid levelBefore riding, check that the brake fluidis above the minimum level mark.Check the brake fluid level with the topof the reservoir level. Replenish thebrake fluid if necessary.
Front brake
Rear brake
WARNING
EWA16011
Improper maintenance can result in
loss of braking ability. Observe
these precautions:
Insufficient brake fluid may al-
low air to enter the brake sys-
tem, reducing braking
performance.
Clean the filler cap before re-
moving. Use only DOT 4 brake
fluid from a sealed container.
1. Brake pad wear indicator groove
11
1. Minimum level mark
1
1. Minimum level mark
Specified brake fluid:
DOT 4
1
Periodic maintenance and adjustment
6-22
6
Use only the specified brake flu-
id; otherwise, the rubber seals
may deteriorate, causing leak-
age.
Refill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
Be careful that water or dust
does not enter the brake fluid
reservoir when refilling. Water
will significantly lower the boil-
ing point of the fluid and may re-
sult in vapor lock, and dirt may
clog the ABS hydraulic unit
valves.
NOTICEECA17641
Brake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
As the brake pads wear, it is normal forthe brake fluid level to gradually godown. A low brake fluid level may indi-cate worn brake pads and/or brakesystem leakage; therefore, be sure to
check the brake pads for wear and thebrake system for leakage. If the brakefluid level goes down suddenly, have aYamaha dealer check the cause beforefurther riding.
EAU22734
Changing the brake fluidHave a Yamaha dealer change thebrake fluid every 2 years. In addition,have the seals of the master cylindersand brake calipers, as well as the brakehoses replaced at the intervals listedbelow or sooner if they are damaged orleaking.
Brake seals: every 2 yearsBrake hoses: every 4 years
Periodic maintenance and adjustment
6-23
6
EAU22762
Drive chain slackThe drive chain slack should bechecked before each ride and adjustedif necessary.
EAU73530
To check the drive chain slack
1. Place the motorcycle on the cen-terstand.
2. Shift the transmission into theneutral position.
3. Measure the drive chain slack asshown.
4. If the drive chain slack is incorrect,adjust it as follows. NOTICE: Im-
proper drive chain slack will
overload the engine as well as
other vital parts of the motorcy-
cle and can lead to chain slip-
page or breakage. If the drive
chain slack is more than 50.0
mm (1.97 in), the chain can dam-
age the frame, swingarm, and
other parts. To prevent this from
occurring, keep the drive chain
slack within the specified limits.
[ECA17791]
EAU63122
To adjust the drive chain slack
Consult a Yamaha dealer before ad-justing the drive chain slack.
1. Take the motorcycle off the cen-terstand, and then put the side-stand down.
2. Loosen the axle nut and the lock-nut on each side of the swingarm.
3. Place the motorcycle on the cen-terstand.
4. To tighten the drive chain, turn thedrive chain slack adjusting bolt oneach side of the swingarm in di-rection (a). To loosen the drivechain, turn the adjusting bolt oneach side of the swingarm in di-rection (b), and then push the rearwheel forward.
1. Drive chain slack
Drive chain slack:
35.0–45.0 mm (1.38–1.77 in)
1
1. Axle nut2. Locknut
21
Periodic maintenance and adjustment
6-24
6
TIP
Using the alignment marks on the drivechain pullers and the notch on eachside of the swingarm, make sure thatboth drive chain pullers are in the sameposition for proper wheel alignment.
5. Take the motorcycle off the cen-terstand, and then put the side-stand down.
6. Tighten the axle nut, then the lock-nuts to their specified torques.
7. Make sure that the drive chainpullers are in the same position,the drive chain slack is correct,
and the drive chain movessmoothly.
EAU23026
Cleaning and lubricating the
drive chainThe drive chain must be cleaned andlubricated at the intervals specified inthe periodic maintenance and lubrica-tion chart, otherwise it will quickly wearout, especially when riding in dusty orwet areas. Service the drive chain asfollows.
NOTICEECA10584
The drive chain must be lubricated
after washing the motorcycle, riding
in the rain or riding in wet areas.
1. Clean the drive chain with kero-sene and a small soft brush.NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents. [ECA11122]
2. Wipe the drive chain dry.
1. Drive chain slack adjusting bolt
(a)
(b)
1
1. Notch2. Alignment mark3. Drive chain puller
Tightening torques:Axle nut:
150 N·m (15 kgf·m, 111 lb·ft)Locknut:
16 N·m (1.6 kgf·m, 12 lb·ft)
31
2
Periodic maintenance and adjustment
6-25
6
may contain substances that
could damage the O-rings.
[ECA11112]
EAU23098
Checking and lubricating the
cablesThe operation of all control cables andthe condition of the cables should bechecked before each ride, and the ca-bles and cable ends should be lubri-cated if necessary. If a cable isdamaged or does not move smoothly,have a Yamaha dealer check or re-place it. WARNING! Damage to the
outer housing of cables may result
in internal rusting and cause inter-
ference with cable movement. Re-
place damaged cables as soon as
possible to prevent unsafe condi-
tions. [EWA10712]
EAU23115
Checking and lubricating the
throttle grip and cableThe operation of the throttle gripshould be checked before each ride. Inaddition, the cable should be lubricat-ed by a Yamaha dealer at the intervalsspecified in the periodic maintenancechart.The throttle cable is equipped with arubber cover. Make sure that the coveris securely installed. Even though thecover is installed correctly, it does notcompletely protect the cable from wa-ter entry. Therefore, use care not topour water directly onto the cover orcable when washing the vehicle. If thecable or cover becomes dirty, wipeclean with a moist cloth.Recommended lubricant:
Yamaha cable lubricant or other suitable cable lubricant
3. Thoroughly lubricate the drivechain with a special O-ring chainlubricant. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as they
Periodic maintenance and adjustment
6-26
6
EAU44276
Checking and lubricating the
brake and shift pedalsThe operation of the brake and shiftpedals should be checked before eachride, and the pedal pivots should be lu-bricated if necessary.
Brake pedal
Shift pedal
EAU23144
Checking and lubricating the
brake and clutch leversThe operation of the brake and clutchlevers should be checked before eachride, and the lever pivots should be lu-bricated if necessary.
Brake lever
Clutch lever
Recommended lubricant:Lithium-soap-based grease
Periodic maintenance and adjustment
6-27
6
EAU23215
Checking and lubricating the
centerstand and sidestand
The operation of the centerstand andsidestand should be checked beforeeach ride, and the pivots and metal-to-metal contact surfaces should be lubri-cated if necessary.
WARNING
EWA10742
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Recommended lubricants:Brake lever:
Silicone greaseClutch lever:
Lithium-soap-based grease
Recommended lubricant:Lithium-soap-based grease
Periodic maintenance and adjustment
6-28
6
EAUM1653
Lubricating the swingarm piv-
ots
The swingarm pivots must be lubricat-ed by a Yamaha dealer at the intervalsspecified in the periodic maintenanceand lubrication chart.
EAU23273
Checking the front forkThe condition and operation of thefront fork must be checked as followsat the intervals specified in the periodicmaintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level sur-face and hold it in an upright posi-tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over. [EWA10752]
2. While applying the front brake,push down hard on the handle-bars several times to check if thefront fork compresses and re-bounds smoothly.
NOTICEECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
Recommended lubricant:Lithium-soap-based grease
Periodic maintenance and adjustment
6-29
6
EAU45512
Checking the steeringWorn or loose steering bearings maycause danger. Therefore, the operationof the steering must be checked as fol-lows at the intervals specified in theperiodic maintenance and lubricationchart.
1. Place the vehicle on the center-stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over. [EWA10752]
2. Hold the lower ends of the frontfork legs and try to move them for-ward and backward. If any freeplay can be felt, have a Yamahadealer check or repair the steer-ing.
EAU23292
Checking the wheel bearings
The front and rear wheel bearings mustbe checked at the intervals specified inthe periodic maintenance and lubrica-tion chart. If there is play in the wheelhub or if the wheel does not turnsmoothly, have a Yamaha dealercheck the wheel bearings.
EAU50212
Battery
The battery is located under the riderseat. (See page 3-34.)This model is equipped with a VRLA(Valve Regulated Lead Acid) battery.There is no need to check the electro-lyte or to add distilled water. However,the battery lead connections need tobe checked and, if necessary, tight-ened.
WARNING
EWA10761
Electrolyte is poisonous and
dangerous since it contains sul-
1. Battery2. Positive battery lead (red)3. Negative battery lead (black)
1
3
2
Periodic maintenance and adjustment
6-30
6
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.
EXTERNAL: Flush with plenty
of water.
INTERNAL: Drink large quan-
tities of water or milk and im-
mediately call a physician.
EYES: Flush with water for 15
minutes and seek prompt
medical attention.
Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.
KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
To charge the battery
Have a Yamaha dealer charge the bat-tery as soon as possible if it seems tohave discharged. Keep in mind that thebattery tends to discharge more quick-ly if the vehicle is equipped with op-tional electrical accessories.
NOTICEECA16522
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (con-
stant-voltage) battery charger is re-
quired. Using a conventional battery
charger will damage the battery.
To store the battery
1. If the vehicle will not be used formore than one month, remove thebattery, fully charge it, and thenplace it in a cool, dry place.NOTICE: When removing the
battery, be sure to turn the main
switch off, then disconnect the
negative lead before discon-
necting the positive lead. [ECA16304]
2. If the battery will be stored formore than two months, check it atleast once a month and fullycharge it if necessary.
3. Fully charge the battery before in-stallation. NOTICE: When install-
ing the battery, be sure to turn
the main switch off, then con-nect the positive lead before
connecting the negative lead.
[ECA16842]
4. After installation, make sure thatthe battery leads are properly con-nected to the battery terminals.
NOTICEECA16531
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
furic acid, which causes severe
Periodic maintenance and adjustment
6-31
6
EAU63134
Replacing the fusesThe fuse boxes and individual fusesare located under the rider seat (seepage 3-34) and behind panel A (seepage 6-9).To access fuse box 1, the main fuse,and the fuel injection system fuse, re-move the rider seat. (See page 3-34.)
TIP
To access the fuel injection systemfuse, remove the starter relay cover bypulling it upward.
To access fuse box 2 and fuse box 3,remove panel A. (See page 6-9.)
1. Fuse box 12. Main fuse3. Fuel injection system fuse4. Fuel injection system spare fuse
1
34
2
1. Radiator fan motor fuse2. Backup fuse (for clock and immobilizer sys-
tem)3. Electronic throttle valve fuse4. ABS solenoid fuse5. ABS motor fuse6. Spare fuse
1 23
45
6
1. Starter relay cover2. Fuel injection system fuse3. Fuel injection system spare fuse
1. Fuse box 22. Fuse box 3
32
1
1
2
Periodic maintenance and adjustment
6-32
6
If a fuse is blown, replace it as follows.1. Turn the key to “OFF” and turn off
the electrical circuit in question.2. Remove the blown fuse, and then
install a new fuse of the specifiedamperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive dam-
age to the electrical system and
possibly a fire. [EWA15132]
3. Turn the key to “ON” and turn onthe electrical circuit in question tocheck if the device operates.
4. If the fuse immediately blowsagain, have a Yamaha dealercheck the electrical system.
1. Parking lighting fuse2. Headlight fuse3. Plug +12V fuse (DC connector, option)4. Plug +12V fuse (DC jack)5. Cruise control fuse6. Brake light fuse7. Signaling system fuse8. Fog lamp fuse (option)9. ABS control unit fuse10.Seat heater fuse (option)11.Spare fuse12.Ignition fuse
1234
11
12
11
10987 6 5
Specified fuses:
Main fuse:50.0 A
Fuel injection system fuse:20.0 A
Specified fuses (fuse box 1):
Radiator fan motor fuse:15.0 A
ABS motor fuse:30.0 A
ABS solenoid fuse:15.0 A
Backup fuse:7.5 A
Electronic throttle valve fuse:7.5 A
Specified fuses (fuse box 2):Fog lamp fuse:
2.0 ABrake light fuse:
1.0 ASignaling system fuse:
7.5 AIgnition fuse:
15.0 AABS control unit fuse:
7.5 ASeat heater fuse:
7.5 A
Specified fuses (fuse box 3):Headlight fuse:
7.5 AParking lighting fuse:
7.5 ACruise control fuse:
1.0 APlug +12V fuse:
2.0 APlug +12V fuse:
2.0 A
Periodic maintenance and adjustment
6-33
6
EAU77470
HeadlightsThis model is equipped with LED-typeheadlights.If a headlight does not come on, checkthe fuses and then have a Yamahadealer check the vehicle.
TIP
When the headlights are set to lowbeam, one headlight will come on.When the headlights are set to highbeam or the passing switch is pushed,both headlights should come on.
NOTICEECA16581
Do not affix any type of tinted film or
stickers to the headlight lens.
EAU54502
Auxiliary lights
This model is equipped with LED-typeauxiliary lights.If an auxiliary light does not come on,have a Yamaha dealer check it.
EAU70540
Brake/tail lightThis model is equipped with an LED-type brake/tail light.If the brake/tail light does not come on,have a Yamaha dealer check it.
1. Auxiliary light
1 1
Periodic maintenance and adjustment
6-34
6
EAU24205
Replacing a turn signal light
bulb1. Remove the turn signal light lens
by removing the screw.
2. Remove the burnt-out bulb bypushing it in and turning it coun-terclockwise.
3. Insert a new bulb into the socket,push it in, and then turn it clock-wise until it stops.
4. Install the lens by installing thescrew. NOTICE: Do not over-
tighten the screw, otherwise the
lens may break. [ECA11192]
EAU58010
Replacing the license plate
light bulb1. Remove the license plate light unit
by removing the nuts and collars,and then remove the license platelight bulb socket (together with thebulb) by pulling it out.
2. Remove the burnt-out bulb bypulling it out.
1. Turn signal light lens2. Screw
1
2
1. Turn signal light bulb
1
1. License plate light unit2. Collar3. Nut4. License plate light bulb socket
1
2
2
4
3
3
Periodic maintenance and adjustment
6-35
6
3. Insert a new bulb into the socket.4. Install the socket (together with
the bulb) by pushing it in, and theninstall the license plate light unit byinstalling the collars and nuts.
EAU25872
TroubleshootingAlthough Yamaha motorcycles receivea thorough inspection before shipmentfrom the factory, trouble may occurduring operation. Any problem in thefuel, compression, or ignition systems,for example, can cause poor startingand loss of power.The following troubleshooting chartsrepresent quick and easy proceduresfor checking these vital systems your-self. However, should your motorcyclerequire any repair, take it to a Yamahadealer, whose skilled technicians havethe necessary tools, experience, andknow-how to service the motorcycleproperly.Use only genuine Yamaha replace-ment parts. Imitation parts may looklike Yamaha parts, but they are ofteninferior, have a shorter service life andcan lead to expensive repair bills.
WARNING
EWA15142
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or prop-
erty damage.
1. License plate light bulb
1
Periodic maintenance and adjustment
6-36
6
EAU42365
Troubleshooting charts
Starting problems or poor engine performance
Check the fuel level inthe fuel tank.
1. FuelThere is enough fuel.
There is no fuel.
Check the battery.
Supply fuel. The engine does not start. Check the battery.
Remove the spark plugsand check the electrodes.
3. Ignition Wipe off with a dry cloth and correct thespark plug gaps, or replace the spark plugs.
Have a Yamaha dealer check the vehicle.
Operate the electric starter.
4. CompressionThere is compression.
There is no compression.
The engine does not start. Have a Yamaha dealer check the vehicle.
Have a Yamaha dealer check the vehicle.
The engine does not start.Check the compression.
Operate the electric starter.
2. Battery The engine turns over quickly.
The engine turns over slowly.
The engine does not start.Check the ignition.
The battery is good.
Check the battery lead connections,and have a Yamaha dealer charge the battery if necessary.
Dry
Wet Operate the electric starter.
Periodic maintenance and adjustment
6-37
6
Engine overheating
WARNING
EWA10401
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hiss-
ing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended cool-ant as soon as possible.
Wait until the engine has cooled.
Check the coolant level in the reservoir and radiator.
The coolant level is OK.
The coolant level is low.Check the cooling systemfor leakage.
Have a Yamaha dealer checkand repair the cooling system.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a Yamaha dealer check and repair the cooling system.
There isleakage.
There is no leakage.
Motorcycle care and storage
7-1
7
EAU37834
Matte color caution
NOTICEECA15193
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-
ished parts.
EAU54661CareWhile the open design of a motorcyclereveals the attractiveness of the tech-nology, it also makes it more vulnera-ble. Rust and corrosion can developeven if high-quality components areused. A rusty exhaust pipe may go un-noticed on a car, however, it detractsfrom the overall appearance of a mo-torcycle. Frequent and proper caredoes not only comply with the terms ofthe warranty, but it will also keep yourmotorcycle looking good, extend itslife and optimize its performance.Before cleaning
1. Cover the muffler outlet with aplastic bag after the engine hascooled down.
2. Make sure that all caps and cov-ers as well as all electrical cou-plers and connectors, includingthe spark plug caps, are tightly in-stalled.
3. Remove extremely stubborn dirt,like oil burnt onto the crankcase,with a degreasing agent and abrush, but never apply such prod-
ucts onto seals, gaskets, sprock-ets, the drive chain and wheelaxles. Always rinse the dirt anddegreaser off with water.
Cleaning
NOTICEECA10773
Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with wa-
ter to clean plastic. However, if
the plastic parts cannot be thor-
oughly cleaned with water, di-
luted mild detergent with water
may be used. Be sure to rinse
Motorcycle care and storage
7-2
7
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake fluid,
antifreeze or electrolyte.
Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.
For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the wind-
shield to make sure that it does
not leave any marks. If the wind-
shield is scratched, use a quality
plastic polishing compound af-
ter washing.
After normal useRemove dirt with warm water, a milddetergent, and a soft, clean sponge,and then rinse thoroughly with cleanwater. Use a toothbrush or bottlebrushfor hard-to-reach areas. Stubborn dirtand insects will come off more easily ifthe area is covered with a wet cloth fora few minutes before cleaning.
After riding in the rain, near the sea oron salt-sprayed roadsSince sea salt or salt sprayed on roadsduring winter are extremely corrosivein combination with water, carry outthe following steps after each ride inthe rain, near the sea or on salt-sprayed roads.
TIP
Salt sprayed on roads in the wintermay remain well into spring.
1. Clean the motorcycle with coldwater and a mild detergent, afterthe engine has cooled down.NOTICE: Do not use warm wa-
ter since it increases the corro-
sive action of the salt. [ECA10792]
2. Apply a corrosion protection sprayon all metal, including chrome-and nickel-plated, surfaces to pre-vent corrosion.
Cleaning the windshieldAvoid using any alkaline or strong acidcleaner, gasoline, brake fluid, or anyother solvent. Clean the windshieldwith a cloth or sponge dampened witha mild detergent, and then wash it offthoroughly with water. For additionalcleaning, use Yamaha WindshieldCleaner or another high-quality wind-shield cleaner. Some cleaning com-pounds for plastics may leavescratches on the windshield. Beforeusing such cleaners, test an area of the
Motorcycle care and storage
7-3
7
windshield which does not affect yourvisibility and which cannot be easilyrecognized.
After cleaning
1. Dry the motorcycle with a chamoisor an absorbing cloth.
2. Immediately dry the drive chainand lubricate it to prevent it fromrusting.
3. Use a chrome polish to shinechrome, aluminum and stainless-steel parts, including the exhaustsystem. (Even the thermally in-duced discoloring of stainless-steel exhaust systems can be re-moved through polishing.)
4. To prevent corrosion, it is recom-mended to apply a corrosion pro-tection spray on all metal,including chrome- and nickel-plat-ed, surfaces.
5. Use spray oil as a universal clean-er to remove any remaining dirt.
6. Touch up minor paint damagecaused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completelybefore storing or covering it.
WARNING
EWA11132
Contaminants on the brakes or tires
can cause loss of control.
Make sure that there is no oil or
wax on the brakes or tires.
If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
NOTICEECA10801
Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
Never apply oil or wax to any
rubber and plastic parts, but
treat them with a suitable care
product.
Avoid using abrasive polishing
compounds as they will wear
away the paint.
TIP
Consult a Yamaha dealer for ad-vice on what products to use.Washing, rainy weather or humidclimates can cause the headlightlens to fog. Turning the headlighton for a short period of time willhelp remove the moisture from thelens.
Motorcycle care and storage
7-4
7
EAU26183
Storage
Short-term
Always store your motorcycle in a cool,dry place and, if necessary, protect itagainst dust with a porous cover. Besure the engine and the exhaust sys-tem are cool before covering the mo-torcycle.
NOTICEECA10811
Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Long-term
Before storing your motorcycle for sev-eral months:
1. Follow all the instructions in the“Care” section of this chapter.
2. Fill up the fuel tank and add fuelstabilizer (if available) to preventthe fuel tank from rusting and thefuel from deteriorating.
3. Perform the following steps toprotect the cylinders, piston rings,etc. from corrosion.a. Remove the spark plug caps
and spark plugs.b. Pour a teaspoonful of engine
oil into each spark plug bore.c. Install the spark plug caps onto
the spark plugs, and thenplace the spark plugs on thecylinder head so that the elec-trodes are grounded. (This willlimit sparking during the nextstep.)
d. Turn the engine over severaltimes with the starter. (This willcoat the cylinder walls with oil.)WARNING! To prevent dam-
age or injury from sparking,
make sure to ground the
spark plug electrodes while
turning the engine over.
[EWA10952]
e. Remove the spark plug capsfrom the spark plugs, and theninstall the spark plugs and thespark plug caps.
4. Lubricate all control cables andthe pivoting points of all levers andpedals as well as of the side-stand/centerstand.
5. Check and, if necessary, correctthe tire air pressure, and then liftthe motorcycle so that both of itswheels are off the ground. Alterna-tively, turn the wheels a little everymonth in order to prevent the tiresfrom becoming degraded in onespot.
6. Cover the muffler outlet with aplastic bag to prevent moisturefrom entering it.
7. Remove the battery and fullycharge it. Store it in a cool, dryplace and charge it once a month.Do not store the battery in an ex-cessively cold or warm place [lessthan 0 °C (30 °F) or more than 30°C (90 °F)]. For more informationon storing the battery, see page6-29.
Motorcycle care and storage
7-5
7
TIP
Make any necessary repairs beforestoring the motorcycle.
Specifications
8-1
8
Dimensions:
Overall length: 2160 mm (85.0 in) Overall width: 850 mm (33.5 in) Overall height: 1375/1430 mm (54.1/56.3 in) Seat height: 850/865 mm (33.5/34.1 in) Wheelbase: 1500 mm (59.1 in) Ground clearance: 135 mm (5.31 in) Minimum turning radius: 3.0 m (9.84 ft)Weight: Curb weight: 215 kg (474 lb)Engine: Combustion cycle: 4-stroke Cooling system: Liquid cooled Valve train: DOHC Cylinder arrangement: Inline Number of cylinders: 3-cylinder Displacement: 847 cm³ Bore × stroke: 78.0 × 59.1 mm (3.07 × 2.33 in)
Compression ratio: 11.5 : 1 Starting system: Electric starter Lubrication system: Wet sumpEngine oil: Recommended brand: YAMALUBE SAE viscosity grades: 10W-40 Recommended engine oil grade: API service SG type or higher, JASO standard MA Engine oil quantity: Oil change: 2.40 L (2.54 US qt, 2.11 Imp.qt) With oil filter removal: 2.70 L (2.85 US qt, 2.38 Imp.qt)Coolant quantity: Coolant reservoir (up to the maximum level mark): 0.25 L (0.26 US qt, 0.22 Imp.qt) Radiator (including all routes): 1.93 L (2.04 US qt, 1.70 Imp.qt)Air filter: Air filter element: Oil-coated paper elementFuel: Recommended fuel: Premium unleaded gasoline (Gasohol [E10] acceptable) Fuel tank capacity: 18 L (4.8 US gal, 4.0 Imp.gal)
Fuel reserve amount: 2.6 L (0.69 US gal, 0.57 Imp.gal)Fuel injection: Throttle body: ID mark: B1J1 00Spark plug(s): Manufacturer/model: NGK/CPR9EA9 Spark plug gap: 0.8–0.9 mm (0.031–0.035 in)Clutch:
Clutch type: Wet, multiple-discDrivetrain:
Primary reduction ratio: 1.681 (79/47) Final drive: Chain Secondary reduction ratio: 2.813 (45/16) Transmission type: Constant mesh 6-speed Gear ratio: 1st: 2.667 (40/15) 2nd: 2.000 (38/19) 3rd: 1.619 (34/21) 4th: 1.381 (29/21) 5th: 1.190 (25/21)
Specifications
8-2
8
6th: 1.037 (28/27)Chassis: Frame type: Diamond Caster angle: 24.0 ° Trail: 100 mm (3.9 in)Front tire: Type: Tubeless Size: 120/70ZR17 M/C (58W) Manufacturer/model: DUNLOP/D222FRear tire: Type: Tubeless Size: 180/55ZR17 M/C (73W) Manufacturer/model: DUNLOP/D222Loading: Maximum load: 179 kg (395 lb) (Total weight of rider, passenger, cargo and accessories)Tire air pressure (measured on cold
tires): 1 person: Front: 225 kPa (2.25 kgf/cm², 33 psi)
Rear: 250 kPa (2.50 kgf/cm², 36 psi) 2 persons: Front: 250 kPa (2.50 kgf/cm², 36 psi) Rear: 290 kPa (2.90 kgf/cm², 42 psi)Front wheel: Wheel type: Cast wheel Rim size: 17M/C x MT3.50Rear wheel: Wheel type: Cast wheel Rim size: 17M/C x MT5.50Front brake: Type: Hydraulic dual disc brake Specified brake fluid: DOT 4Rear brake: Type: Hydraulic single disc brake Specified brake fluid: DOT 4Front suspension: Type: Telescopic fork Spring: Coil spring Shock absorber: Hydraulic damper
Wheel travel: 137 mm (5.4 in)Rear suspension: Type: Swingarm (link suspension) Spring: Coil spring Shock absorber: Gas-hydraulic damper Wheel travel: 142 mm (5.6 in)Electrical system: System voltage: 12 V Ignition system: TCI Charging system: AC magnetoBattery: Model: YTZ10S Voltage, capacity: 12 V, 8.6 Ah (10 HR)Bulb wattage: Headlight: LED Brake/tail light: LED Front turn signal light: 10.0 W Rear turn signal light: 10.0 W Auxiliary light: LED
Specifications
8-3
8
License plate light:5.0 W
Meter lighting:LED
Neutral indicator light:LED
High beam indicator light:LED
Turn signal indicator light:LED
Engine oil and Coolant warning light:LED
Engine trouble warning light:LED
ABS warning light:LED
Cruise control “SET” indicator light:LED
Cruise control “ON” indicator light:LED
Immobilizer system indicator light:LED
Shift timing indicator light:LED
Traction control system indicator light:LED
Fuse(s):
Main fuse:50.0 A
Headlight fuse:7.5 A
Fog lamp fuse:2.0 A
Brake light fuse:1.0 A
Signaling system fuse:7.5 A
Ignition fuse:15.0 A
Parking lighting fuse:7.5 A
Radiator fan motor fuse:15.0 A
Fuel injection system fuse:20.0 A
ABS control unit fuse:7.5 A
ABS motor fuse:30.0 A
ABS solenoid fuse:15.0 A
Cruise control fuse:1.0 A
Backup fuse:7.5 A
Electronic throttle valve fuse:7.5 A
Seat heater fuse:7.5 A
Plug +12V fuse:2.0 A
Plug +12V fuse:2.0 A
Consumer information
9-1
9
EAU53562
Identification numbersRecord the vehicle identification num-ber, engine serial number, and themodel label information in the spacesprovided below. These identificationnumbers are needed when registeringthe vehicle with the authorities in yourarea and when ordering spare partsfrom a Yamaha dealer.
VEHICLE IDENTIFICATION NUMBER:
ENGINE SERIAL NUMBER:
MODEL LABEL INFORMATION:
EAU26401
Vehicle identification number
The vehicle identification number isstamped into the steering head pipe.Record this number in the space pro-vided.
TIP
The vehicle identification number isused to identify your motorcycle andmay be used to register your motorcy-cle with the licensing authority in yourarea.
EAU26442
Engine serial number
The engine serial number is stampedinto the crankcase.
EAU26461
Model label
1. Vehicle identification number
1
1. Engine serial number
1. Model label
1
1
Consumer information
9-2
9
The model label is affixed to the loca-tion shown. Record the information onthis label in the space provided. Thisinformation will be needed when order-ing spare parts from a Yamaha dealer.
EAU69910
Diagnostic connector
The diagnostic connector is located asshown.
EAU74702
Vehicle data recordingThis model’s ECU stores certain vehi-cle data to assist in the diagnosis ofmalfunctions and for research and de-velopment purposes. This data will beuploaded only when a special Yamahadiagnostic tool is attached to the vehi-cle, such as when maintenance checksor service procedures are performed.Although the sensors and recordeddata will vary by model, the main datapoints are:
Vehicle status and engine perfor-mance dataFuel-injection and emission-relat-ed data
Yamaha will not disclose this data to athird party except:
With the consent of the vehicleownerWhere obligated by law For use by Yamaha in litigationFor general Yamaha-conductedresearch purposes when the datais not related to an individual vehi-cle nor owner
1. Diagnostic connector
1
10-1
10
Index
A
ABS.......................................................3-27ABS warning light ...................................3-6Air filter element ....................................6-15Auxiliary DC connector .........................3-44Auxiliary DC jack...................................3-43Auxiliary lights.......................................6-33
B
Battery ..................................................6-29Brake and clutch levers, checking and
lubricating...........................................6-26Brake and shift pedals, checking and
lubricating...........................................6-26Brake fluid, changing ............................6-22Brake fluid level, checking ....................6-21Brake lever ............................................3-26Brake lever free play, checking.............6-19Brake light switches..............................6-20Brake pedal...........................................3-27Brake/tail light .......................................6-33
C
Cables, checking and lubricating .........6-25Canister.................................................6-11Care ........................................................7-1Catalytic converter................................3-33Centerstand and sidestand, checking
and lubricating....................................6-27Clutch lever...........................................3-25Clutch lever free play, adjusting ...........6-19Coolant .................................................6-13Cruise control indicator lights.................3-5Cruise control switches ..........................3-4Cruise control system.............................3-8
D
Data recording, vehicle .......................... 9-2Diagnostic connector ............................. 9-2Dimmer/Pass switch .............................. 3-4Display, main screen ............................ 3-11Display, menu screen ........................... 3-15D-mode (drive mode) ........................... 3-25Drive chain, cleaning and lubricating ... 6-24Drive chain slack .................................. 6-23Drive mode switch.................................. 3-4
E
Engine break-in ...................................... 5-3Engine idling speed, checking ............. 6-15Engine oil .............................................. 6-11Engine oil and Coolant warning light...... 3-7Engine serial number.............................. 9-1Engine trouble warning light................... 3-5
F
Front and rear brake pads, checking ... 6-20Front fork, adjusting ............................. 3-39Front fork, checking ............................. 6-28Fuel....................................................... 3-31Fuel consumption, tips for reducing ...... 5-3Fuel tank cap........................................ 3-30Fuel tank overflow hose ....................... 3-33Fuses, replacing ................................... 6-31
H
Handlebar position, adjusting .............. 3-39Handlebar switches................................ 3-3Hazard switch......................................... 3-4Headlight beams, adjusting.................. 3-38Headlights ............................................ 6-33
Helmet holder ....................................... 3-37High beam indicator light ....................... 3-5Horn switch.............................................3-4
I
Identification numbers ............................9-1Ignition circuit cut-off system ...............3-45Immobilizer system .................................3-1Immobilizer system indicator light ..........3-7Indicator lights and warning lights ..........3-5
L
License plate light bulb, replacing ........6-34M
Main switch/steering lock .......................3-2Maintenance and lubrication, periodic....6-5Maintenance, emission control
system ..................................................6-3Matte color, caution ................................7-1Model label .............................................9-1
N
Neutral indicator light..............................3-5P
Panel, removing and installing ................6-9Parking ....................................................5-4Part locations ..........................................2-1
Q
Quick shift system ................................3-26R
Rider seat height, adjusting ..................3-35S
Safety information...................................1-1Seats .....................................................3-34
Index
10-2
10
Spark plugs, checking.......................... 6-10Specifications ......................................... 8-1Starting the engine ................................. 5-1Steering, checking................................ 6-29Stop/Run/Start switch ............................ 3-4Storage ................................................... 7-4Storage compartment .......................... 3-38Swingarm pivots, lubricating ................ 6-28
T
TCS switch ............................................. 3-4Throttle grip and cable, checking and
lubricating........................................... 6-25Throttle grip free play, checking........... 6-15Tires...................................................... 6-16Tool kit .................................................... 6-2Traction control system........................ 3-28Traction control system indicator light ... 3-6Troubleshooting.................................... 6-35Troubleshooting charts......................... 6-36Turn signal indicator lights ..................... 3-5Turn signal light bulb, replacing ........... 6-34Turn signal switch................................... 3-4
V
Valve clearance .................................... 6-16Vehicle identification number ................. 9-1
W
Wheel bearings, checking .................... 6-29Wheels.................................................. 6-18Windshield ............................................ 3-38
Shift pedal.............................................3-26Shock absorber assembly, adjusting....3-41Sidestand ..............................................3-44
Shift indicator light ..................................3-6Shifting ....................................................5-2