RE927S 3G GSM Communicator - Resolution Productsresolutionproducts.com/.../2015/03/RE927S_3G-GSM-Communicator.pdfON when the unit is registered with the local GSM network CS ... RE927S_3G

RE927S_3G GSM Communicator Page 1 of 6 16-May-14 24-Hour Tech Support Line: (715)808-0164

www.ResolutionProducts.com

Wireless Security Solutions

RE927S-03-00 3G GSM Communicator with Z-wave

Features

• Connects panels to GSM Network

• Compatible with: o GE Simon XT

o GE Simon XT

• Enables: o Alarm Reporting o Interactive Control Functions o Ethernet data reliability o Z-Wave Communicator included Key Instructions

• The same unit works for GE Simon XT & GE Simon XTi.

• The RE927S mounts inside the GE Simon XT panel and communicates with the GE Simon XT and GE Simon XTi via the Expansion Connector.

• The antenna should be mounted in a location that will optimize cellular signal strength. Mount as high in the building as possible. Mount the Antenna as far as possible from large metal objects and sources of interference.

Operation

Event Reporting:

Events are reported to both the CMS monitoring receiver and the Securenet interactive server. The following events are reported by default:

Alarms Alarm cancels Openings Closings System Low Battery System Low Battery Restoral AC Power Fail AC Power Restoral

Interactive Control:

The system may be controlled remotely through the Securenet interactive platform.

Z-Wave

Z-Wave devices can be controlled via the Interactive function.

Siren (RE116-C)

Can be used with a Simon XT Future: Simon XTi

Revert to Factory Default Button Press and hold for 5 seconds: Resets the board and keeps all settings Press and hold for 10 seconds: Reverts board back to the factory default settings



Picture

LEDs

Ethernet LEDs Indication

Power (Green)

ON and flashing once per second when the board is powered and running

GSM (Red)

ON when the unit is registered with the local GSM network

CS (Red)

ON when the connection to the CMS central station is established

Platform (Amber)

On when the connection to the Panel, and connection to the SiteControl interactive server is established

Z-Wave

Module

Revert to Factory

Default Button

GSM Antenna

Connector

Z-Wave

Antenna

GSM Card

Status LEDs



Programming:

1) Refer to server setup instructions and set up the account on the Site Control Dealer Portal.

2) Disarm the System.

3) Power down the GE Simon XT system.

4) Plug RE927S into the back of the GE Simon XT control panel. (Picture below) board communicates via the Expansion Connector.

5) String the GSM antenna to mount in a location for best GSM signal.

6) Apply power to the GE Simon XT system.

7) The keypad should display “Resolution GSM Module”.

8) Installation is complete.

GSM Communicator in the

Expansion Connector



Specifications

Current Draw: 230 mA Nominal Temperature Range: 0F to 120F Housing dimensions: 2x4x1/2 inches Specifications subject to change without notice.

GE Simon XT Firmware Version Compatibility 1.3 (minimum) Notices “GE”, “Honeywell”, “DSC”, “2GIG” and “Napco” are trademarks owned by General Electric Company, Honeywell International Inc., Tyco Safety Products Canada LTD, 2GIG Technologies Inc., and NAPCO Security Systems, Inc., respectively. Resolution Products, Inc. products will function with one of either GE, Honeywell, DSC or Napco systems. However, no Resolution product is produced by, endorsed by, nor is officially associated with GE, Honeywell, DSC or Napco. Resolution recommends verifying proper enrollment and operation, per control panel installation instructions, at installation. Warranty Resolution Products, Inc. will replace products that are defective in their first five (5) years.



FCC Notice

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference. (2)This device must accept any interference that may be received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the Resolution Engineering, Inc. could void the user's authority to operate this equipment. FCC ID: U5X-RE927 This device contains FCC ID: QISMU509C RF Exposure: To satisfy FCC RF Exposure requirements for mobile and base station transmission devices, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during operation. To ensure compliance, operation at closer than this distance is not recommended.

The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.



IC Notice This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)l'appareil ne doit pas produire de brouillage, et (2)l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Model: RE927S IC: 8310A-RE927 This device contains IC: 6369A-MU509C Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.

Documents

RE927S 3G GSM Communicator - Resolution Productsresolutionproducts.com/.../2015/03/RE927S_3G-GSM-Communicator.pdfON when the unit is registered with the local GSM network CS ... RE927S_3G