16
R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING DEPARTMENT Subject: Environment Conservation and Hazard Management Subject Code: 3300003 Assignment: - 1 Que.1 Write advantages of energy plantation. Que.2 Explain Primary and Secondary effects of earthquake. Que.3 List advantages of waste recycling. Que.4 Explain in brief Need for Renewable energy. Que.5 Write the uses of wind map and wind tables. Que.6 Explain food chain. Que.7 Explain layer of atmosphere. Que.8 Write component and characteristics of Biogas. Que.9 Write need of energy Conservation. Que.10 List effects of Acid rain. Que.11 Explain disaster management including all main point concern it. Que.12 Write short note on Energy Plants. Que.13 Write a short note on Greenhouse gases. Que.14 Suggestion for new construction in earthquake sensitive area. Que.15 List the advantages of flat plate collector.

R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

  • Upload
    others

  • View
    2

  • Download
    0

Embed Size (px)

Citation preview

Page 1: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R.C. TECHNICAL INSTITUTE SOLA

MECHANICAL ENGINEERING DEPARTMENT

Subject: Environment Conservation and Hazard Management

Subject Code: 3300003

Assignment: - 1

Que.1 Write advantages of energy plantation.

Que.2 Explain Primary and Secondary effects of earthquake.

Que.3 List advantages of waste recycling.

Que.4 Explain in brief Need for Renewable energy.

Que.5 Write the uses of wind map and wind tables.

Que.6 Explain food chain.

Que.7 Explain layer of atmosphere.

Que.8 Write component and characteristics of Biogas.

Que.9 Write need of energy Conservation.

Que.10 List effects of Acid rain.

Que.11 Explain disaster management including all main point concern it.

Que.12 Write short note on Energy Plants.

Que.13 Write a short note on Greenhouse gases.

Que.14 Suggestion for new construction in earthquake sensitive area.

Que.15 List the advantages of flat plate collector.

Page 2: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R.C. TECHNICAL INSTITUTE SOLA

MECHANICAL ENGINEERING DEPARTMENT

Subject: Environment Conservation and Hazard Management

Subject Code: 3300003

Assignment: - 2

Que.1 Explain causes & effects of acid rain. Also explain control of acid rain.

Que.2 How can you save fuel in domestic energy consumption?

Que.3 Compare horizontal axis wind mill with vertical axis wind mill.

Que.4 Explain construction of a solar cooker with neat sketch.

Que.5 List the advantages of biogas plant.

Que.6 Write the characteristics of biomass.

Que.7 Explain pyranometer with neat sketch.

Que.8 Explain in detail about various energy plants to obtain biomass energy.

Que.9 Write about general instructions for protection of people during and after

Earthquake.

Que.10 Explain how cyclone occurs? What are the effects of the cyclone?

Que.11 Explain waste recycling methods.

Que.12 What is air pollution? Explain the causes responsible for Air Pollution.

Que.13 Explain layers of atmosphere.

Que.14 Enlist the types of Vertical Axis Wind Turbine and explain anyone with a neat

sketch.

Que.15 Explain concept of Sustainable Development.

Page 3: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R.C. TECHNICAL INSTITUTE SOLA

MECHANICAL ENGINEERING DEPARTMENT

Subject: Environment Conservation and Hazard Management

Subject Code: 3300003

Assignment: - 3

Que.1 Describe Biotic and Abiotic Natural Resources in detail.

Que.2 Discuss the Potential of Renewable Energy Sources in India?

Que.3 Explain Noise as pollution. What are negative effects of noise pollution?

Que.4 Explain the principles of measurements of solar radiations.

Que.5 Write short note on P-N Junction.

Que.6 Explain function of Biogas plant with sketch in detail.

Que.7 Write steps for energy conservation in Transportation.

Que.8 Discuss the reasons for environmental pollution.

Que.9 Explain Horizontal axis Wind turbines.

Que.10 Explain Wind farms.

Que.11 Explain effects of atmosphere on solar radiations.

Que.12 Explain causes of Earthquake

Que.13 Explain basic functions of disaster management department.

Que.14 Write short note on Urbanization.

Que.15 Explain greenhouse effect.

Page 4: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R.C.Technical Institute –Sola, Ahmedabad

Mechanical Department

Mechanical Engineering for Printing-(3335801)

Assignment -01

Sr

No. Question

1 Give list and also define all the mechanical properties.

2 Give the Name Of physical and thermal Properties.

3 List materials used for engineering application.

4 Draw neat Sketch Of Vernier caliper and micrometer .

5 What do you mean by foundry?

6 Explain selection of pattern material.

7 Explain L.C.M. of Vernier

caliper and micrometer.

8 Write the modes of power transmission also define (1) slip (2) speed ratio

(3) power transmission

9 Draw the Neat Sketch of Compound Belt Drive and

Compound Gear train.

10 List advantages and disadvantages of belt drive.

11 Enlist types of core and explain any two in detail.

12 Give the advantages of sheet metal process.

13 Enlist types of pattern material and explain any two in detail.

14 Write short note on fasteners.

15 In a power transmission of flat belt drive the tension in slack side (T2) is

3000N Whereas initial tension (To ) is 5000N. Find the tension in tight

side (T1 ).

Page 5: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

Assignment -02

Sr No. Question

1 Draw the displacement diagram of simple harmonic motion with proper

nomenclature 2 Give advantages and disadvantages of casting process.

3 Enlist types of followers.

4 Give differences between Hot and cold working process

5 Draw the displacement diagram of uniform velocity with proper

nomenclature. 6 Draw neat sketch of horizontal milling machine and name the parts.

7 Draw neat sketch of lathe machine with nomenclature.

8 List the operations which can be performed on lathe machine and draw

any two operation with nomenclatures.

9 Explain construction and working of single stage reciprocating air

compressor with figure.

10 Why filters are required in machine?

11 Explain Applications of Pumps in Printing Industry.

12 Explain the applications of Air compressor.

13 Draw neat sketch of centrifugal pump.

14 What is the function of drilling machine? List any two use of drilling

machine. 15 List types of rolling mills.

Page 6: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

Assignment -03

Sr

No. Question

1 List the methods used for power transmission.

2

Describe function of inter cooler and after cooler used

in air cooler.

3

As a printing student, why you need to understand mechanical

fundamentals?

4 Draw neat sketch of rolling contact bearing. List any two places where is

used.

5 Draw neat sketch of rope drive and list its advantages and applications.

6 Explain simple gear train by neat sketch and give its application.

7 What is cam? Explain in detail. Which type of cams and followers are

used in various machineries?

8 List any six types of tools and spanners used in general maintenance.

9 What are the types of gears used in printing industries in various

machines? Draw neat sketch of spur gear.

10 Explain reverted gear train with neat sketch.

11 Explain operations which can be performed on drilling machine with neat

sketch.

12 What is priming? Explain with respect to pumps. Which pump requires

frequent priming after stoppage?

13 What is the function of idler pulley used in belt drive? Explain with neat

sketch.

14 Give detailed classification the air compressor.

15 Enlist types of pattern allowances

Page 7: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R. C. TECHNICAL INSTITUTE, SOLA

Name of Department- MECHANICAL

SEMESTER – 1

Subject Name: Basic Engg. Drg. Subject Code: 3300007

Assignment – 1

Chapter name: 1)Engineering drawing aids,2)Planning,layout and scaling of

drawing,3)Lines,lettering and dimensioning

(1) Why Engineering Drawing is called Engineer’s language?

(2) Prepare a list of equipments useful to engineering drawing and their uses.

(3) Write cautions in the use of Instruments.

(4) Write the standard size of Drawing Board.

(5) List the various size of drawing sheets are according to BIS.

(6) Prepare a list of equipments used for tracing.

(7) Draw a specimen Title Block with information.

(8) List types of Lettering.

(9) Why margins are kept?

(10) What are folding marks? Why they are necessary?

(11) Differentiate with the help of sketches “ Aligned System” and “Unidirectional System”.

(12) Explain rules and guidelines for Dimensioning.

(13) Explain with the help of sketches dimension methods for different sizes of circles.

(14) Explain with the help of sketches the difference between chain dimensioning and parallel

dimensioning .

(15) Why should an engineering student study engineering drawing?

(16) Explain planning in engineering drawing?

(17) Explain care and storage of original drawing?

(18) Why scale is required for preparing drawing? List recommended scales for engineering drawing.

Page 8: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

Chapter name: Geometric construction

(19)To Construct a perpendicular at a given point P on a line from O1 to30mm to the line O1O2. =100mm.

(19 a) Draw a regular Pentagon of side length 50mm by special methods.

(20) Construct a regular Pentagon with the distance from its centre to one of its corner is 45mm.

(21) To Construct a common interior (cross) tangent to the given equal circle of radius 25mm.

(22) To Construct an arc of circle through three nonlinear given points O1, O2, O3 .

(23) Construct a regular Pentagon having side of 35mm using three circle method.

(24)Draw an arc of 20mm radius touching sides of angles (i) 60° (ii) 140°

Chapter name: Engineering curves

(25) List out the types of Engg. Curves.

(26) Define: Eccentricity, Vertex or Apex.

(27) Define w.r.t Spiral: Pole, Radius, Vector, Convolution.

(28) Construct an ellipse with the distance between focus and the directrix is 80mm and e=3/5. 8

(29) Draw an ellipse having major axis 140mm and minor axis 100mm by Half- Concentric method and the

other half by rectangle method.

(30) Draw Hyperbolla passing through point Po whose X and Y co-ordinates are (50,60) respectively.

(31) A ball is thrown up into the air, reaches a height of 80 M and falls 140M away from the point of throw.

Draw the path of ball, assuming it to be Parabolic. Take suitable scale.

(32) Major axis of an ellipse an ellipse is 100mm. Distance of foci from each end is 15mm.Draw an ellipse by

intersecting arc method.

(33)Draw Archimedean Spiral for750°.The smallest and greatest radii are 30mm and 200mm respectively.

(34) State the uses of Spiral , Cycloid group curves.

(35) A circle of 60mm diameter rolls along a straight path, without slipping. Draw the curve traced by point “P”

on the circumference for one revolution of the circle. Name the curve.

(36) Draw an involute for a circle of 30 mm diameter

Chapter name: Orthographic projection

(37) Explain system of Orthographic Projection.

(38) Draw symbols of first and third angle projection method.

(39) What are the various important types of projection.

Page 9: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

(40) Which projection method is preferably used in Indian industries?

(41) A pictorial view of an object is shown in fig given below. Draw its following views by using Third Angle

Projection Method. Give necessary dimensions as per Aligned method. Draw the symbol of Third Angle

projection method.

(i) Front View looking from direction X (ii) Top View (iii) Left hand side View

(42) A pictorial view of an object is shown in fig given below. Draw its following views by using First Angle

Projection Method. Give necessary dimensions as per Aligned method. Draw the symbol of first Angle projection

method.

(i) Front View looking from direction X (ii) Top View (iii) Right hand side View

Page 10: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

Assignment – 2

Chapter name: Projection of points,lines and planes

(1) Write name of projections, corresponding projections plane and notation system.

(2) What are the three different co-ordinates planes?

(3) Write nine types of (positions) of Points ?

(4) Draw the projections of the following points taking a common reference line, keeping the distance between

any two consecutive points is 25mm.

(i) P,30mm in front of VP and 40mm behind HP.

(ii) Q, in HP and 25mm in front of HP.

(iii) R,25mm above HP and 40mm behind VP.

(iv) S, in VP and 40mm above HP.

(v) T,30mm below HP and 50mm behind VP.

(vi) U,in HP and 40mm behind VP.

(vii) V,40mm below HP and 25mm in front of VP.

(Viii) W,in VP and 40mm below HP.

(5) Define notation w.r.t Proj. of lines: α, β, γ ,θ, μ,

(6) A line AB 90mm long is inclined 30° to HP and 45° to VP. Point A is 15mm above HP and 10mm in

front of VP. Draw its projections.

(7) A line PQ, 100mm long is inclined 30° to HP and 45° to VP. Point A is 15mm above HP and 25mm in front

of VP. Draw its projections.

(8) The top view and front of a line AB 100mm long measures 75mm and 85mm respectively. . Point A is

10mm below HP and 20mm behind VP. Draw its projections and find inclination of line with HP & VP.

(9) The distance between end projector of line PQ is 80mm .One end P is 20mm above the HP and 30mm in

front of VP while other end Q is 60mm above HP50 mm in front of VP. Draw the projection of line. Find true

inclination.

(10)A regular hexagonal plate of 50mm sides has corner in the HP. Its surfaces is inclined at 60° to HP and the

top of view diagonals through the which is in the HP is at 45° with VP. Draw the projections.

(11)A semi circular plate of 60mm diameter has its straight edge (diameter) in the VP inclined at 45° to

HP. The surface of the plate makes 30° to VP. Draw the projections

.

Page 11: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

Assignment – 3

Chapter name: Isometric projection

(1) Draw an Isometric Scale. Take Maximum dimension on True (normal) scale 100 mm.

What is an Isometric Lines? Write their proportion.

(2) By a simple sketch illustrate how an arc of a circle is drawn in an isometric

view?

(3) Explain the difference between isometric drawing and isometric projection

(4) Draw an Isometric Projection from view given below.

Page 12: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

(5) Figure shows two views of an object. Draw an Isometric Projection.

.

(6) Draw an isometric drawing from the views given in figure 2.

Page 13: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R. C. TECHNICAL INSTITUTE, SOLA

MECHANICAL DEPARTMENT

SEMESTER – 1

Subject Name: Fundamental of Mechanical Engineering Subject Code: 3300015

Assignment – 1

1) Explain Use of mechanical engineering in day to day life.

2) Give the types of (1) Bolts (2) nuts (3) washers.

3) Give the types of (1) bearings (2) screws (3) rivets.

4) Explain uses of (1) bearings (2) screws (3) rivets.

5) Explain uses of (1) Bolts (2) nuts (3) washers.

6) Define shafts and axles.

7) Give the types of pipe materials.

8) Explain plumbing and plumber.

9) Give the names of different pipe fittings and explain any 3 with figure in detail.

10) Explain Types, specifications and uses of spanners.

11) Explain Types, specifications and uses of hand tools.

12) Give the names of different power tools.

13) Give the names of different hand tools.

14) What is power transmission and explain modes of power transmission.

15) Explain applications of power transmission.

16) Explain types of flat belt drive.

17) Explain with fig. Compound belt drive.

18) Give the types of gear train

19) Explain compound Gear train with fig.

20) Explain Epicyclic Gear Train with fig.

21) Explain applications of couplings in power transmission.

22) Explain Causes and remedies of general accidents in power transmission.

23) Define (1) Speed ratio (2) Train Value.

24) Explain Safety norms to be followed in mechanical based industries / shop floors.

25) Explain Safety norms to be followed for preventing accidents and damage in power

transmission.

Page 14: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

26) What is Welding and give names of different types of welding.

27) Explain Arc welding with fig.

28) Explain gas welding with fig.

29) Give the names of various parts used in gas welding.

30) Explain Precautions and safety during arc and gas welding.

31) Explain Brazing in Detail

32) Explain soldering in detail

33) Give the difference between (1) Soldering (2) brazing and (3) welding

34) Explain concept of Gas cutting

35) What do you mean by foundry and explain Process of getting cast material.

36) Give the names of basic machine tools

37) Explain Working principle of lathe.

38) Explain Working principle of drilling machine.

39) Explain Working principle of milling machines.

40) Explain Types of operation which can be performed on lathe machine.

41) Explain Types of operation which can be performed on milling machine

Page 15: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R. C. TECHNICAL INSTITUTE, SOLA

MECHANICAL DEPARTMENT

SEMESTER – 1

Subject Name: Fundamental of Mechanical Engineering Subject Code: 3300015

Assignment-2

1) Explain Steam generation process.

2) Give the properties of steam.

3) Give the classification of boilers.

4) Explain working principle of cochran boiler.

5) Explain working principle of bebcock wilcox boiler.

6) Give the accessories and mountings of boiler.

7) Give the Application of boilers.

8) Explain classification and working of prime mover.

9) Explain common troubles and remedies for prime mover.

10) Draw the figure of cochran boiler.

11) Draw the figure of bebcock Wilcox boiler.

12) Explain the meaning and classification of I.C.ENGINE.

13) Explain the working of petrol engine.

14) Explain the working of diesel engine

15) Explain main parts and their functions of i.c.engine.

16) EXplain performance parameters for i.c.engine.

17) GIve the different applications of i.c.engine.

18) Explain troubles and remedies for petrol and diesel engine.

19) Give the difference between s.i. engine and c.i. engine.

20) Give the difference between two stroke engine and four stroke engine.

Page 16: R.C. TECHNICAL INSTITUTE SOLA MECHANICAL ENGINEERING ...€¦ · Assignment -02 Sr No. Question 1 Draw the displacement diagram of simple harmonic motion with proper nomenclature

R. C. TECHNICAL INSTITUTE, SOLA

MECHANICAL DEPARTMENT

SEMESTER – 1

Subject Name: Fundamental of Mechanical Engineering Subject Code: 3300015

Assignment – 3

1) Explain working of single acting reciprocating pump with line diagram.

2) Explain working of Francis turbine with neat sketch.

3) Define material handling. Classify material handling equipments.

4) Select suitable material handling equipment for following situation:

i) For loading heavy components in multi floor building ii) To prepare concrete

mixture iii) To transport coal as burning fuel in power station iv) For handling

machine parts, structure parts, building blocks etc.

5) Write selection criteria for crane.

6) State application of compressed air.

7) Mention types of air compressors.

8) Explain working principle of centrifugal pump with neat sketch.

9) State the criteria for selection of material handling equipment.

10) Discuss need of material handling equipment.

11) State advantages and disadvantages of belt conveyor.

12) Draw Centrifugal Pump. Name all parts clearly.

13) List various types of Water Turbine. Explain any One in detail.

14) Give difference between reciprocating pump and centrifugal pump.

15) Explain direct acting hydraulic lift.

16) Give the name of material handling equipments use for following processes: (1)

Lifting of heavy articles. (2) Transport human from one floor to another. (3)

Handling material in the sea.