RapidNet 8 Fibre - HellermannTyton · outs are deployed in the final connections. Straight-through, cross-over or flipped pairs? Example part number matrix for RapidNet Cassettes

.

R a p i d N e t 8 F i b r eB e t t e r Te c h n o l o g y t h r o u g h I n n o v a t i o n

.

Introduct ion

.

Recently updated standards as well as several under development for future introduction, indicate

data rates of 25Gbps, 40Gbps, 100Gbps, 200Gbps and 400Gbps. These future technologies are

based around utilising two or eight fibres per physical link and depend on several factors including

the bit rate of the laser and the number of separate wavelengths (λ) that are utilised in a single

fibre. Two-fibre transmission lines are not new and nor is the use of twelve fibre parallel fibre

transmission lines, however the future suggests that the number of required transmission lines will

cycle from two to eight and back to two again over the foreseeable future.

A key consideration for data centre owners and designers is maximising fibre utilisation whilst

ensuring an optimised physical layer design that is capable of scaling as the demands placed

upon it do. This is never more important than in Hyperscale and Edge data centres where

unprecedented growth is being observed. Innovative fibre transceiver designs and optical

components are delivering higher data rates per lane, enabling the total number of required fibres

to be reduced.

Green-field fibre deployments are able to take advantage of the eight fibre solutions, whereas

legacy installations may require innovative migration strategies to maximise the utilisation of the

physical infrastructure. HellermannTyton’s range of transition cassettes offers the perfect resolution

(see page 10).

The topic of fibre polarity is further complicated when eight (or twelve) fibres are considered. The

following pages start to discuss the subject of polarity and which aspects influence component

selection. HellermannTyton offer the three standard polarity options of A, B and C in the RapidNet

8 Fibre solution (see page 6 and 7).

Demand for faster data rates, access times and higher performance continues to drive data centre designs. The latest designs incorporating leaf & spine and edge architectures are creating reduced latency, more flexibility and the ability to scale upgrades as and when required.

.

4

What is an MTP® connector? The MTP connector is a high performance MPO connector with multiple engineered

product enhancements to improve optical and mechanical performance when compared to generic MPO connectors.

The MTP connector is in complete compliance with all MPO connector standards including the EIA/TIA-604-5 FOCIS 5 and the IEC-61754-7. The MTP connector is inter-matable with all generic MPO-style connectors that are compliant to these industry standards.

Generic MPO connectors are limited in performance and are not able to offer the high performance levels of the US Conec MTP connector.

RapidNet Overview

Modular and pre-terminatedRapidNet is HellermannTyton’s fully patented pre-terminated, pre-tested modular cabling

system, eliminating the need for on-site terminations and reducing installation times

significantly. All terminations are housed in the RapidNet cassette, ensuring complete protection

and strain relief of the cables.

Manufactured at HellermannTyton’s purpose built facility in Northampton, UK, RapidNet

provides choice and flexibility to the installer and end user by offering an extensive range of

connectivity options in both fibre and copper formats. All RapidNet formats are based on a

common cassette delivering consistent performance, breadth of range and maximum flexibility.

RapidNet delivers a full end to end pre-terminated solution for any network application

including data centres, comms rooms, commercial offices, call centres, hospital and

educational environments.

Polarising pips for correct alignment upon insertion into panels

Available in MTP, LC and SC as well as copper options

Internal strain relief to reduce risk of snagging and tugging of sensitive copper and fibre

‘Second end’ options available including: cassette to cassette, fibre fan out and MTP cable

Common cassette panel interface

The anatomy of a RapidNet cassette

.

5

The HellermannTyton 8 Fibre range is offered in various configurations and options to suit typical

deployment requirements of flexibility, performance and optical loss management.

Connection options

Cassette to Cassette The cassette to cassette offers localised patching fields at

both ends of the link. This configuration is beneficial when

there isn’t the immediate requirement to utilise all the

ports.

Cassette to Fan Out With the cassette providing local patching at one end,

the fan out can be connected directly into the active

equipment, reducing losses and saving cabinet space.

Transition Cassettes Transition cassettes are used to convert from multi-fibre

to single fibre (MTP to LC) or different fibre count MTP to

MTP. In either case they use a standard cassette with a

rear MTP connection, ideal for use in either re-configuring

existing installed cables or when access and cable

management may be limited.

Fan Out to Fan Out CablesThe fan out option removes localised patching at both

ends, saving space in the cabinets and reducing optical

losses in the link. These cables are offered in various

configurations and are particularly suited to applications

where the active equipment or hardware at each end is

located either in the same cabinet or row.

Patch leads There is a wide range of patch leads available, all suitable

for the above connection methods and are supplied in

various configurations and lengths to suit the optical

polarity of the channel.

.

6

Large data centres are already demanding 40G and 100G transmission speeds. When specifying for these projects it is important to understand the various f ibre systems and configurations that wil l be able to support these higher data rates.

Key up

Key down

Key down

Absence of pin on female connector

Male pin location

Polar ity in the Data Centre

Figure 1. Polarity A Straight through configuration with key up - key down connectors

Position 1 - 12 Position 12 - 1

Key up

White dot

For multi‐fibre designs using MTP connectors, the TIA 568 standard lays out three methods for

configuring systems to ensure that proper connections are made: polarity options A, B and

C. Each of these options deliver the transition from a transmit position to a receive position in

a different way, and each option requires a specific backbone and patch cable that differs in

construction to the other polarity types.

Before we look at the different polarity options on page 7, illustrated below is an MTP

connection showing how the connectors differ in terms of male, female, key up and key

down configurations.

Each MTP connector has a key on one side of the connector body. When the key sits on top, this

is known as the key up position. In this orientation, each of the fibre holes in the connector is

numbered in sequence 1 to 12 from left to right. Each connector is additionally marked with a

white dot on the connector body which identifies the position 1 side of the connector when it is

plugged in.

White dot

.

7

Fibre polarity becomes a little more complex when working

with multi-fibre MTP type cables and connectors. Industry

standards list three different polarity methods for MTP; A, B

and C. And each polarity option requires the use of a different

MTP cable.

• Polarity A uses a straight-through MTP trunk cable with a

key up connector on one end and a key down connector on

the other end so that the fibre located in Position 1 arrives at

Position 1 at the other end (see figure 2).

• Polarity B uses key up connectors on both ends to achieve

a cross-over or reversed polarity meaning the fibre located in

Position 1 arrives at Position 12 at the opposite end, the fibre

located in Position 2 arrives at Position 11 at the opposite

end and so on (see figure 3).

• Polarity C uses a key up connector on one end and a key

down on the other end like the Polarity A method, but the

flip happens within the cable itself where each pair of fibres

are flipped so that the fibre in Position 1 arrives at Position

2 at the opposite end and the fibre in Position 2 arrives at

Position 1 (see figure 4).

With the 3 different polarity types, the potential for mistakes in

deployment is higher so it is important that the correct cables

are used.

The two types of adaptors, key up - key up and key up - key

down also have a role to play in determining the end-to-end

channel polarity, whether MTP’s are used throughout or fan

outs are deployed in the final connections.

Straight-through, cross-over or f l ipped pairs?

Example part number matrix for RapidNet Cassettes

Example part number matrix for Fibre Leads

Polarity - Ordering the Right Products

R FW

PolarityT - Straight-throughM - Straight-through

Cassette to MTP Connector

W - Cross-over

PolarityS - Straight-throughC - Cross-over (LC and 12 core MTP)W - MTP 24 core

Cross-over

RapidNet Fibre Fibre Lead

N LF S

When ordering RapidNet MTP fibre products, it is important

that the correct cables and connectors are identified for the

required configuration or polarity type. The product tables on

pages 10 to 17 help determine which products and its part

number are needed for each polarity option.

POLARITY A (straight-through)

Fibre Colour Pos Pos Fibre Colour

BLUE 1 1 BLUE

ORANGE 2 2 ORANGE

GREEN 3 3 GREEN

BROWN 4 4 BROWN

GREY 5 5 GREY

WHITE 6 6 WHITE

RED 7 7 RED

BLACK 8 8 BLACK

YELLOW 9 9 YELLOW

PURPLE 10 10 PURPLE

PINK 11 11 PINK

AQUA 12 12 AQUA

POLARITY B (cross-over / reversed)


BLUE 1 1 AQUA

ORANGE 2 2 PINK

GREEN 3 3 PURPLE

BROWN 4 4 YELLOW

GREY 5 5 BLACK

WHITE 6 6 RED

RED 7 7 WHITE

BLACK 8 8 GREY

YELLOW 9 9 BROWN

PURPLE 10 10 GREEN

PINK 11 11 ORANGE

AQUA 12 12 BLUE

POLARITY C (pairs flipped)


BLUE 1 1 ORANGE

ORANGE 2 2 BLUE

GREEN 3 3 BROWN

BROWN 4 4 GREEN

GREY 5 5 WHITE

WHITE 6 6 GREY

RED 7 7 BLACK

BLACK 8 8 RED

YELLOW 9 9 PURPLE

PURPLE 10 10 YELLOW

PINK 11 11 AQUA

AQUA 12 12 PINK

Figure 2.

Figure 3.

Figure 4.

.

8

Performance

OM41~10G

40G (SWDM4)

40G (SR4)

100G (SR10)

100G (SR4)

25G 50G

Colour Magenta (MG)

No. of Fibres 2 2 8 20 8 2 4 / 2

Max. channel length 450 400 150 150 100 100 100

Connector contribution 1.2 1.5 1 1 1.5 1.5 1.5

Cable 1.3 1.3 0.45 0.45 0.3 0.3 0.3

Total 2.6 2.8 1.5 1.5 1.9 1.9 1.9

OM5 1~10G40G

(SWDM4)40G (SR4)

100G (SR10)

100G (SR4)

25G 50G

Colour Lime (LG)

No. of Fibres 2 2 8 20 8 2 2

Max. channel length 400 400 150 150 100 150 150

Connector contribution 1.4 1.5 1 1 1.5 1.5 1.5

Cable 1.5 1.3 0.45 0.45 0.3 0.45 0.45

Total 2.9 2.8 1.5 1.5 1.9 2.0 2.0

Subject to technical changes. Performance measured in dB.

The 8 fibre system will support high speed 10G networks and beyond. High port densities can be

achieved using RapidNet MTP cassettes providing up to 144 fibres per cassette or up to 576 fibres

in 1U of rack space.

HellermannTyton only use quality ‘Elite’ components in the pre-terminated MTP assemblies,

helping to ensure the highest possible performance from the fibre with minimal losses.

With the increase in speeds and demand for performance, the channel lengths and loss budgets

are reducing to accommodate and achieve these higher speeds. The tables below illustrate the

fibre performance for OM4 and OM5 8 fibre configurations:

8 Fibre Performance – Loss and Length Summary

The 8 Fibre pre-terminated RapidNet solution delivers high performance across OM4 and OM5 fibre.

.

1

9

RapidNet 8 Fibre

RapidNet Fibre Cassettes

LC

Rear MTP Connectivity 10

Cassette to MTP 10

Fibre Adaptor Mounting Module

13

MTP

Transition Cassette with Rear MTP Connectivity

11

48 Fibre 11

96 Fibre 12

144 Fibre 12

Fibre Adaptor Mounting Module

13

Fan Out Cables

LC MTP to LC Transition Cable 17

MTP

8 Fibre MTP to MTP Fan Out 14

24 Fibre MTP to MTP Fan Out 15

MTP to MTP Transition Cable 16

RapidNet Accessories

RapidNet Panels

1U 6 Port Copper/Fibre 18

1U 6 Port Hybrid 18

1U 6 Port Angled 19

2U 6 Port Angled 19

4U Distribution Chassis 20

Cable Management 1U Rear Cable Management 20

.

10

TYPE DrawingPerformance

category H W D Port Count Colour Article-No.

RNFTQ08-LCMMM4-XX.XX OM427 102 130 8

MG 859-23196

RNFTQ08-LCMMM5-XX.XX OM5 LG 859-23197

RNFTQ16-LCMMM4-XX.XX OM427 102 130 16

MG 859-23198

RNFTQ16-LCMMM5-XX.XX OM5 LG 859-23199

RNFTQ24-LC3MM4-XX.XX OM427 102 130 24

MG 859-23200

RNFTQ24-LC3MM5-XX.XX OM5 LG 859-23201

RNFTQ24-LC1MM4-XX.XX OM427 102 130 24

MG 859-23202

RNFTQ24-LC1MM5-XX.XX OM5 LG 859-23203Subject to technical changes. All dimensions in mm. Colour code: Magenta (MG) and Lime Green (LG).


category H W D PolarityPort

Count Colour Article-No.

RNFMQ08-LC1FM4-10.0M OM427 102 130

A

8MG 859-23229

RNFMQ08-LC1FM5-10.0M OM5 LG 859-23230

RNFMQ16-LC1FM4-10.0M OM427 102 130 16

MG 859-23231

RNFMQ16-LC1FM5-10.0M OM5 LG 859-23232

RNFMQ24-LC1FM4-10.0M OM427 102 130 24

MG 859-23233

RNFMQ24-LC1FM5-10.0M OM5 LG 859-23234

Subject to technical changes. All dimensions in mm. Part Numbers given are for 10m loom as an example. Other lengths available on request. Colour code: Magenta (MG) and Lime Green (LG).

The RapidNet 8 Fibre LC Cassette with MTP connectivity is pre-terminated offering up to 24 ports in one cassette and has 1,2 or 3 MTP connector/s on the rear of the case for use with MTP back bone cables or fibre fan outs. The RapidNet LC Cassette with MTP connectivity solution has been designed to make installation quicker and easier, especially where space is limited, by providing reduced installation times, efficient use of space, flexible configurations and high performance.

The RapidNet 8 Fibre LC Cassette pre-terminated with single MTP at the second end has been designed to make installation quicker and easier, especially where space is limited, by providing reduced installation times, efficient use of space, flexible configurations and high performance.

Product Description

Product Description

RapidNet LC 24 port fibre cassette with 3 Rear MTP Connection

RapidNet LC 24 port fibre cassette to MTP Connector

Features and Benefits

Features and Benefits

• Up to 96 fibres in 1U of Space• Significantly reduced installation times• Available in OM4 and OM5• Interchangeable with other RapidNet

Cassettes• MTP rear connector ideal for installations in

areas of limited space• Pre-tested with test results supplied• Male MTP Connectors

• Up to 96 fibres in 1U of Space• Significantly reduced installation times• Available in OM4 and OM5• Interchangeable with other RapidNet

Cassettes• Pre-tested with test results supplied• Female MTP Connector

RapidNet Fibre LC

RapidNet Fibre LC

Rear MTP Connectivity

Cassette to MTP

Connectivity ProductsRapidNet Fibre

Further information and datasheets at www.htdata.co.uk/products/rapidnet

.

11

The RapidNet 8 Fibre MTP Cassette pre-terminated with MTP connectivity solution has been designed to make installation quicker and easier, especially where space is limited, by providing reduced installation times, efficient use of space, flexible configurations and high performance.

Product Description

RapidNet MTP 6 x 8 fibre cassette with 2 x 24 fibre Rear MTP Connectors

Features and Benefits• Up to 192 fibres in 1U of Space• High performance low loss Elite®

connectors from US Conec • Significantly reduced installation times• Available in OM4 and OM5• Interchangeable with other RapidNet

Cassettes• Pre-tested with test results supplied• Male MTP Connectors

RapidNet MTP Transition CassetteRear MTP Connectivity

TYPE Drawing Performance category H W D Port Count Article-No.

RNFT324-MC1MM4-XX.XX OM427 102 130 3

859-23204

RNFT324-MC1MM5-XX.XX OM5 859-23205

RNFT324-MCMMM4-XX.XX OM427 102 130 3

859-23206

RNFT324-MCMMM5-XX.XX OM5 859-23207

RNFT648-MCMMM4-XX.XX OM427 102 130 6

859-23208

RNFT648-MCMMM5-XX.XX OM5 859-23209

Subject to technical changes. All dimensions in mm.

The RapidNet MTP VHD Cassette to Cassette is pre-terminated with each cassette offering 6 x 8 fibre MTP connectors, which enables up to 192 fibres in 1U of rack space, with 4 cassettes fitting into a RapidNet Panel.

The RapidNet MTP VHD solution has been designed to meet the demands of the data centre by providing reduced installation times, efficient use of space, flexible configurations and high performance. This high density fibre solution is particularly suited to use in Storage Area Network (SAN) applications.

Product Description

RapidNet MTP 6 x 8 fibre cassette

Features and Benefits• Up to 192 fibres in 1U of Space• High performance low loss Elite® connectors

from US Conec • Significantly reduced installation times• Available in OM4 and OM5• Interchangeable with other RapidNet


RapidNet MTP 48 FibreCassette to Cassette




RNFW648-MCMCM4-10.0M OM427 102 130 A 6

MG 859-23210

RNFW648-MCMCM5-10.0M OM5 LG 859-23211

RNFT648-MCMCM4-10.0M OM427 102 130 B 6

MG 859-23212

RNFT648-MCMCM5-10.0M OM5 LG 859-23213




.

12



Product Description









RNFW6H4-MCMCM4-10.0M OM427 102 130 A 6

MG 859-23218

RNFW6H4-MCMCM5-10.0M OM5 LG 859-23219

RNFT6H4-MCMCM4-10.0M OM427 102 130 B 6

MG 859-23220

RNFT6H4-MCMCM5-10.0M OM5 LG 859-23221





Product Description









RNFWV96-MCMCM4-10.0M OM427 102 130 A 12

MG 859-23214

RNFWV96-MCMCM5-10.0M OM5 LG 859-23215

RNFTV96-MCMCM4-10.0M OM427 102 130 B 12

MG 859-23216

RNFTV96-MCMCM5-10.0M OM5 LG 859-23217



.

13

The RapidNet Fibre Adaptor Mounting Module has been designed to allow the RapidNet solution to be used in areas with limited access or restricted space where a RapidNet Cassette cannot be used.

The module is pre-loaded with adaptors which allows ruggedised fan outs to be presented in RapidNet panels and offering a maximum of 144 or 288 fibres in a single cassette which equates to 576 or 1152 fibres in 1U of space.

Product Description



RNAFX06-MTPBK Multimode 27 102 60 6 BK 859-21925

RNAFX12-MTPBK Multimode 27 102 60 12 BK 859-21911

Subject to technical changes. All dimensions in mm. Colour code: Black (BK).

12 MTP Fibre Adaptor Mounting Module

Features and benefits• Ideal for installations with limited access or

restricted space• Allows ruggedised fan outs to be presented

in RapidNet Panels• Fits into a standard RapidNet Panel• Maximum of 1152 fibres in 1U of Space

MTP Fibre Adaptor Mounting Module6 or 12 Port MTP Cassette

The RapidNet Fibre Adaptor Mounting Module has been designed to allow the RapidNet solution to be used in areas with limited access or restricted space where a RapidNet Cassette cannot be used.

The module is pre-loaded with adaptors which allows ruggedised fan outs to be presented in RapidNet panels and offering a maximum of 24 fibres in a single adaptor which equates to 96 fibres in 1U of space.

Product Description

24 Core LC Fibre Adaptor Mounting Module

Features and benefits• Ideal for installations with limited access or

restricted space• Allows ruggedised fan outs to be presented

in RapidNet Panels• Fits into a standard RapidNet Panel• Maximum of 96 fibres in 1U of Space

LC Fibre Adaptor Mounting Module24 Core LC Cassette



RNAFQ02-LCMAMultimode 27 102 60 8

MG 859-23222

RNAFQ02-LCLG LG 859-23223


MG 859-23224



MG 859-23226


Subject to technical changes. All dimensions in mm. Colour code: Magenta (MG) and Lime Green (LG).



.

14


category 1st End 2nd End Polarity Colour Article-No.

FLS08M4-MFMFXM-10.0MOM4

1 x 8F MTP

1 x 8F MTP

AMG

855-32163

FLW08M4-MFMFXM-10.0M B 855-32164

FLS08M5-MFMFXG-10.0MOM5

ALG

855-32165

FLW08M5-MFMFXG-10.0M B 855-32166


3 x 8F MTP

3 x 8F MTP

AMG

855-32167

FLW024M4-MFMFXM-10.0M B 855-32168


ALG

855-32169

FLW024M5-MFMFXG-10.0M B 855-32170


6 x 8F MTP

6 x 8F MTP

AMG

855-32171

FLW48M4-MFMFXM-10.0M B 855-32172


ALG

855-32173

FLW48M5-MFMFXG-10.0M B 855-32174

FLS96M4-MFMF12M-10.0MOM4

12 x 8F MTP

12 x 8F MTP

AMG

855-32175

FLW96M4-MFMF12M-10.0M B 855-32176

FLS96M5-MFMF12G-10.0MOM5

ALG

855-32177

FLW96M5-MFMF12G-10.0M B 855-32178

Subject to technical changes. Other polarity options available. All dimensions in mm. Part Numbers given are for 10m loom as an example. Other lengths available on request. Colour code: Magenta (MG) and Lime Green (LG).

The MTP to MTP Fan Out is designed to provide a high density inter-connect which uses minimum space making it an ideal solution for patching active hardware in data centres where space is at a premium.

The Fan Out cable is a multi-core cable that has a smaller diameter than the standard fibre patch lead and therefore takes up less space in the trays and pathways.

Product Description

12 x 8 fibre MTP to 12 x 8 fibre MTP Fan Out

Features and Benefits• High performance low loss Elite®

Connectors from US Conec• Compatible with all MTP RapidNet Cassettes• Available in OM4 and OM5• Pre-tested with test results supplied• Female MTP Connectors

MTP to MTP Fan Out8 Fibre MTP Fan Out Cable



.

15


category1st End

2nd End Polarity Colour Article-No.


1 x 24F MTP

1 x 24F MTP

AMG

855-32179

FLW24M4-MFMFXM-10.0M B 855-32180


ALG

855-32181

FLW24M5-MFMFXG-10.0M B 855-32182


2 x 24F MTP

2 x 24F MTP

AMG

855-32183

FLW48M4-MFMF2M-10.0M B 855-32184


ALG

855-32185

FLW48M5-MFMF2G-10.0M B 855-32186


4 x 24F MTP

4 x 24F MTP

AMG

855-32187

FLW96M4-MFMF4M-10.0M B 855-32188


ALG

855-32189

FLW96M5-MFMF4G-10.0M B 855-32190

FLSH4M4-MFMF6M-10.0MOM4

6 x 24F MTP

6 x 24F MTP

AMG

855-32191

FLWH4M4-MFMF6M-10.0M B 855-32192

FLSH4M5-MFMF6G-10.0MOM5

ALG

855-32193

FLWH4M5-MFMF6G-10.0M B 855-32194




Product Description




MTP to MTP Fan out24 Fibre MTP Fan Out Cable



.

16



Product Description




MTP to MTP Fan outTransition Cables




3 x 8F MTP

1 x 24F MTP

AMG

855-32195

FLW24M4-MFMF31M-10.0M B 855-32196


ALG

855-32197

FLW24M5-MFMF31G-10.0M B 855-32198


3 x 8F MTP

2 x 12F MTP

AMG

855-32199

FLW24M4-MFMF32M-10.0M B 855-32200


ALG

855-32201

FLW24M5-MFMF32G-10.0M B 855-32202


4 x 24F MTP

12 x 8F MTP

AMG

855-32203

FLW96M4-MFMF412M-10.0M B 855-32204


ALG

855-32205

FLW96M5-MFMF412G-10.0M B 855-32206




.

17



FLS08M4-MFLFXM-10.0MOM4

1 x 8F MTP4 x LC Duplex

AMG

855-32207

FLC08M4-MFLFXM-10.0M B 855-32208

FLS08M5-MFLFXG-10.0MOM5

ALG

855-32210

FLC08M5-MFLFXG-10.0M B 855-32211

FLS24M4-MFLFXM-10.0MOM4

1 x 24F MTP

12 x LC Duplex

AMG

855-32213

FLC24M4-MFLFXM-10.0M B 855-32214

FLS24M5-MFLFXG-10.0MOM5

ALG

855-32216

FLC24M5-MFLFXG-10.0M B 855-32217

FLS24M4-MFLF3M-10.0MOM4

3 x 8F MTP12 x LC Duplex

AMG

855-32219

FLC24M4-MFLF3M-10.0M B 855-32220

FLS24M5-MFLF3G-10.0MOM5

ALG

855-32222

FLC24M5-MFLF3G-10.0M B 855-32223


MTP to LC Fan outTransition Cables


Connectors from US Conec• Compatible with all MTP RapidNet Cassettes• Available in OM4 and OM5• LC Fan Out ideal for inter-connect with

active hardware• Pre-tested with test results supplied• Female MTP Connectors

The MTP to LC Fan Out is designed to provide a high density inter-connect which uses minimum space making it an ideal solution for patching active hardware in data centres where space is at a premium. The MTP connector offers high density connectivity and the LC Fan Out provides LC connectors.


Product Description

3 x 8 fibre MTP to 12 x LC fibre LC Duplex Fan Out



.

18

The RapidNet 6 port Patch Panel accommodates four 6 port copper or fibre cassettes. The panel offers dual labelling fields for each cassette and is supplied with Rack Snap fixings as standard.

The RapidNet Cassettes simply push into the panel, snapping in with a push down clip. A fully loaded 1U panel presents 24 Category 6A UTP, Category 6 or Category 5e RJ45 ports.

Product Description

TYPEHeight H

(mm)Width W

(mm)Depth D

(mm)Port

count Colour Article-No.

RNA6UXX-PA1URS-XX.XX 44.0 483.0 56.0 Unloaded Black (BK) 859-30019

Subject to technical changes.

RapidNet 1U 4 Port Panel

Features and benefits• Fits all 19” racks, frames and cabinets• Supplied with Rack Snaps as standard • Simple, easy insertion with push down clip• Accommodates 4 Category 6A UTP,

Category 6, Category 5e or fibre cassettes• Dual labelling fields and labelling software

with Alpha Label• Also available in 2U 48 port configuration

RapidNet Accessories1U 6 Port Copper/Fibre Cassette Panel

The RapidNet panel is manufactured from 1.5mm matt black powder coated mild steel to the standard 19“ width and has dual labelling fields with a magnifying lens which can be customised through Alpha Label software at www.htdata.co.uk.

The panel is supplied with Rack Snap fixings as standard, panels can also be supplied with Cage Nuts, screw fixings or without fixings if required.

Technical Description

The 1U RapidNet Hybrid Panel provides a simple ‚Mix and Match‘ approach for both copper and fibre RapidNet. The panel offers capacity for the equivalent of 1U of fibre and 1U of copper in 1U of rack space, giving a saving of 1U of space each time the panel is used.

The panels allow for a combination of 12 port high density copper RapidNet and 12 or 24 core fibre (direct terminated or MTP) or high density copper and RapidNet MTP VHD for up to 288 fibres. There are two configurations available.

Product Description

TYPEHeight H

(mm)Width W

(mm)Depth D

(mm) Colour Article-No.

RNAHUXX-PA1URS-HH.SS 44.0 483.0 72.0 Black (BK) 859-30042

RNAHUXX-PA1URS-HS.HS 44.0 483.0 72.0 Black (BK) 859-30043


RapidNet 1U Hybrid Panel

Features and benefits• Equivalent of 1U of fibre and 1U of copper

in 1U of rack space• Maximum combined capacity of 24 copper

ports and 288 fibre using RapidNet MTP VHD

• Typical configuration 24 fibre and 24 copper ports

• Label fields for identification of all ports

RapidNet Accessories1U Hybrid Copper/Fibre Panel

The RapidNet Hybrid panel is manufactured from matt black powder coated mild steel to the standard 19“ width.

The panel is supplied with Rack Snap fixings as standard, panels can also be supplied with Cage Nuts, screw fixings or without fixings if required.

The panel has dual labelling fields which can be customised through Alpha Label software at www.htdata.co.uk.


Connectivity ProductsRapidNet Accessories


.

19

The 1U 24 port panel accommodates four fibre fanout modules. The angled design of the panel removes the need for the use of front cable management increasing capacity by up to 50%.

The panel offers dual labelling for each cassette and a central labelling for U identification and is supplied with Rack Snap fixings as standard.

The RapidNet fibre fanout modules simply push into the panels, snapping in with a push down clip. An optional rear cable manager is also available.

Product Description

TYPEHeight H

(mm)Width W

(mm)Depth D

(mm)Port


RNA6UXX-PE1URS 44.0 482.0 106.0 24 Black (BK) 859-30058


RapidNet 1U Angled Panel

Features and benefits• Angled design provides increase rack

capacity• Accommodates 4 RapidNet Short Body

Cassettes• Simple, easy insertion with push down clip• Clear screen printed dual labelling fields• Central panel labelling for each U space• Supplied with Rack Snaps as standard• Optional rear cable manager available• Also available in 2U 48 port configuration

RapidNet Accessories1U 6 Port Cassette Angled Panel

The RapidNet Angled panel is manufactured from 1.6mm powder coated mild steel making it rigid and robust.

The panel has a matt black finish and is screen printed with port numbers 1 to 24 as well as clear port identification labelling areas for easy user identification which can be customised through Alpha Label software at www.htdata.co.uk.

The panels is supplied with Rack Snap as standard, panels can also be supplied with Cage Nuts, screw fixings or without fixings if required


The 2U 48 port panel accommodates eight fibre fanout modules. The angled design of the panel removes the need for the use of front cable management increasing capacity by up to 50%.

The panel offers dual labelling for each cassette and a central labelling for U identification and is supplied with Rack Snap fixings as standard.

The RapidNet fibre fanout modules simply push into the panels, snapping in with a push down clip. An optional rear cable manager is also available.

Product Description

TYPEHeight H

(mm)Width W

(mm)Depth D

(mm)Port


RNA6UXX-PE2URS 88.0 482.0 106.0 48 Black (BK) 859-30062


RapidNet 2U Angled Panel

Features and benefits• Angled design provides increase rack

capacity• Accommodates 8 RapidNet Short Body

Cassettes• Simple, easy insertion with push down clip• Clear screen printed dual labelling fields• Central panel labelling for each U space• Supplied with Rack Snaps as standard• Optional rear cable manager available• Also available in 1U 24 port configuration

RapidNet Accessories2U 6 Port Cassette Angled Panel

The RapidNet Angled panel is manufactured from 1.6mm powder coated mild steel making it rigid and robust.

The panel has a matt black finish and is screen printed with port numbers 1 to 48 as well as clear port identification labelling areas for easy user identification which can be customised through Alpha Label software at www.htdata.co.uk.

The panels is supplied with Rack Snap as standard, panels can also be supplied with Cage Nuts, screw fixings or without fixings if required




.

20

The HellermannTyton 4U Distribution Chassis is designed for use with the RapidNet pre-terminated solution. The 4U panel accommodates up to 16 RapidNet cassettes covering a range of density requirements from high density 2,304 fibre MTP connections, standard density 384 fibre LC connections or 96 copper ports.

The chassis has integrated front and rear cable management for patch cords, trunks and back bone cables with 8 side cable entry points each with a separate anchor point.

The chassis is fitted with hinged front and rear doors with dedicated labelling fields for simple port and RapidNet loom identification. The front door can be removed to provide ease of access during initial implementation and installation.

Sliding mounting brackets are supplied to allow forward and backward movement to suit the mounting post position within the rack or cabinet.

Product Description

TYPEPerformance

CategoryHeight H

(mm)Width W

(mm)Depth D


RNA6UXX-PD4UCN-XX.XX Single Mode, Multimode 176.0 483.0 401.0 Black (BK) 859-30053


RapidNet 4U Distribution Chassis (shown with Front Door Open)

Features and benefits• Fits into standard 19” racks and cabinets• 4U of vertical space can accommodate up

to16 RapidNet cassettes• Maximum of 2,304 fibres or 96 copper

ports per chassis• Hinged front and rear doors • Front and rear labelling for port/loom

identification• Front and rear cable management • Adjustable mounting brackets to aid

positioning within the rack or cabinet

RapidNet Accessories4U Distribution Chassis

The RapidNet 4U Distribution Chassis is manufactured from 1.5mm powder coated mild steel and the doors and cable management are manufactured from polycarbonate making a rigid and robust panel.

The front and rear doors are supplied with a white re-useable label which provides clear identification enabling simple port and RapidNet loom identification.


The rear cable manager has been designed to provide rear cable strain relief for the RapidNet 12, 6 and 4 port cassette panels. The cable manager has 4 cable anchor points for up to a maximum of 48 cables (8 bundles of 6) enabling use with the high density panels.

Product Description

TYPEHeight H

(mm)Width W

(mm)Depth D


RNRCM 44.0 483.0 230.0 Black (BK) 859-35056


Rapidnet 1U Rear Cable Manager

Features and benefits• Provides cable strain relief• Lightweight aluminium construction• Helps maintain bend radius for optimum

performance• For use with RapidNet 12, 6 and 4 port

panels

RapidNet Accessories1U Rear Cable Manager

The RapidNet rear cable manager is manufactured from lightweight aluminium and offers cable strain relief which supports the weight of the RapidNet cable loom.




.

Even big things have small beginnings. You have to work with what you’ve got – and that was exactly what our company founder Paul Hellermann did back in 1935. Inspired by the small rubber tube in bicycle valves, he developed a process for binding electric cables with rubber: the Hellermann grommet and three-pronged pliers. The first two of the hundreds of patents filed since then.

.

You wil l f ind your local contact here:

Expert ise worldwide

Europe

HellermannTyton GmbH – AustriaRennbahnweg 651220 ViennaTel.: +43 12 59 99 55-0Fax: +43 12 59 99 11Email: [email protected]

HellermannTyton – BulgariaEmail: [email protected]

HellermannTyton – Czech RepublicEmail: [email protected]

HellermannTyton – DenmarkIndustrivej 44A, 1.4000 RoskildeTel.: +45 702 371 20Fax: +45 702 371 21Email: [email protected]

HellermannTyton – FinlandÄyritie 12 B01510 VantaaTel.: +358 9 8700 450Fax: +358 9 8700 4520Email: [email protected]

HellermannTyton S.A.S. – France2 rue des Hêtres - CS 8054378197 Trappes CedexTel.: +33 1 30 13 80 00Fax: +33 1 30 13 80 60Email: [email protected]

HellermannTyton GmbH – GermanyGroßer Moorweg 4525436 TorneschTel.: +49 4122 701-0Fax: +49 4122 701-400Email: [email protected]

HellermannTyton KFT – HungaryKisfaludy u. 131044 BudapestTel.: +36 1 369 4151Fax: +36 1 369 4151Email: [email protected]

HellermannTyton Ltd – IrelandUnit A5 Cherry OrchardBusiness ParkBallyfermot, Dublin 10Tel.: +353 1 626 8267Fax: +353 1 626 8022Email: [email protected]

HellermannTyton S.r.l. – ItalyVia Visco, 3/535010 Limena (PD)Tel.: +39 049 767 870Fax: +39 049 767 985Email: [email protected]

HellermannTyton B.V. –Belgium/NetherlandsVanadiumweg 11-C3812 PX AmersfoortTel.: +31 33 460 06 90Fax: +31 33 460 06 99Email (NL): [email protected] (BE): info@HellermannTyton.bewww.HellermannTyton.nlwww.HellermannTyton.be

HellermannTyton AS – NorwayNils Hansens vei 130667 OsloTel.: +47 23 17 47 00Fax: +47 22 97 09 70Email: [email protected]

HellermannTyton Sp. z o.o. – PolandKotunia 11162-400 SłupcaTel.: +48 63 2237 111Fax: +48 63 2237 110Email: [email protected]

HellermannTyton – RomaniaEmail: [email protected]

OOO HellermannTyton – Russia40/4, Pulkovskoe roadBC Technopolis Pulkovo, office A 8081196158, St. PetersburgTel.: +7 812 386 00 09Fax: +7 812 386 00 08Email: [email protected]

HellermannTyton – SloveniaBranch Office LjubljanaPodružnica Ljubljana, Ukmarjeva 21000 LjubljanaTel.: +386 1 433 70 56Fax: +386 1 433 63 21Email: [email protected]

HellermannTyton España s.l. –Spain / PortugalAvda. de la Industria 37 2° 228108 Alcobendas, MadridTel.: +34 91 661 2835Fax: +34 91 661 2368Email: [email protected]

HellermannTyton AB – SwedenIsafjordsgatan 516440 KistaTel.: +46 8 580 890 00Fax: +46 8 580 348 02Email: [email protected]

HellermannTyton Engineering GmbH – TurkeySaray Mah Dr. Adnan Büyükdeniz Cad. No:4Akkom Office Park 2. Blok Kat: 1034768 Ümraniye-İstanbulTel.: +90 216 687 03 40Fax: +90 216 250 32 32Email: [email protected]

HellermannTyton Ltd – UKWilliam Prance RoadPlymouth International Medicaland Technology ParkPlymouth, Devon PL6 5WRTel.: +44 1752 701 261Fax: +44 1752 790 058Email: [email protected]

HellermannTyton Ltd – UKSharston Green Business Park1 Robeson WayAltrincham Road, WythenshaweManchester M22 4TYTel.: +44 161 947 2200Fax: +44 161 947 2220Email: [email protected]

HellermannTyton Ltd – UKCley Road, Kingswood LakesideCannock, StaffordshireWS11 8AATel.: +44 1543 728282Fax: +44 1543 728284Email: [email protected]

HellermannTyton Data Ltd – UKWaterside House, Edgar Mobbs Way Northampton NN5 5JE Tel.: +44 1604 707 420Fax: +44 1604 705 454Email: [email protected]

Middle East

HellermannTyton – UAEEmail: [email protected]

North America

HellermannTyton – CanadaTel.: +1 905 726 1221Fax: +1 905 726 8538Email: [email protected]

HellermannTyton – MexicoTel.: +52 333 133 9880Fax: +52 333 133 9861Email: [email protected]

HellermannTyton – USATel.: +1 414 355 1130Fax: +1 414 355 7341Email: [email protected]

South America

HellermannTyton – ArgentinaTel.: +54 11 4754 5400Fax: +54 11 4752 0374Email: [email protected]

HellermannTyton – BrazilTel.: +55 11 4815 9000Fax: +55 11 4815 9030Email: [email protected]

Asia-Pacific

HellermannTyton – AustraliaTel.: +61 2 9525 2133Fax: +61 2 9526 2495Email: [email protected]

HellermannTyton – ChinaTel.: +86 510 8528 2536Fax: +86 510 8528 2731Email: [email protected]

HellermannTyton – Hong KongTel.: +852 2831 9090Fax: +852 2832 9381Email: [email protected]

HellermannTyton – IndiaTel.: +91 120 413 3384Email: [email protected]

HellermannTyton – JapanTel.: +81 3 5790 3111Fax: +81 3 5790 3112Email: [email protected]

HellermannTyton – Republic of KoreaTel.: +82 32 833 8012Fax: +82 32 833 8013Email: [email protected]

HellermannTyton – PhilippinesTel.: +63 2 752 6551Fax: +63 2 752 6553Email: [email protected]

HellermannTyton – SingaporeTel.: +65 6 586 1919Fax: +65 6 752 2527Email: [email protected]

HellermannTyton – ThailandTel.: +662 237 6702 / 266 0624Fax: +662 266 8664Email: [email protected]

Africa

HellermannTyton – South AfricaTel.: +27 11 879 6600Fax: +27 11 879 6603Email: [email protected]

.

Wherever you need us - we are there for you

If you are looking for local information, please visit our website www.HellermannTyton.comChoose your country and you will be redirected to the respective

HellermannTyton.

.

BRO

-RN

-8F-

R20

HellermannTyton Data LtdWaterside House, Edgar Mobbs Way Northampton NN5 5JE United Kingdom Tel: +44 (0) 1604 706633 Fax: +44 (0) 1604 705454Email: [email protected] www.htdata.co.uk

Documents

RapidNet 8 Fibre - HellermannTyton · outs are deployed in the final connections. Straight-through, cross-over or flipped pairs? Example part number matrix for RapidNet Cassettes