NEW GENERATION OF
CEHISA EDGEBANDERS
RAPID
Model RAPID-1
TECHNICAL DATA:
� Working materials:
Roller edgebanding (Melamine, Veneer, PVC/ABS) …..……………..0,4-2
mm
� Max.-min. Panel thickness……….……………………………...………8-60 mm
� Max.-min. Panel lenght …………………………...………..unlimited-120 mm
� Max.-min. Panel width…………………………...……….……unlimited-75 mm
� Drag fed speed …………………..……………………………..…....15 m/min.
� Air pressure required………….…………………………...……...6-7 Kg. / cm2
FEEDING STATION: Edgebanding materials in roll are fed
automatically. Equipped with
a guillotine for P.V.C. up to 2 mm of thickness. Timer
controlled automatic feed allowing
the precise adjustment of the infeed surplus and minimizing the
waste of edging material.
GLUING STATION M2-NS: New design with improved thermodynamics,
granting a shorter heating with less power consumption (2,5 kW); •
The molten glue is injected at the upper and the lower points of
the application roller where heating elements are built in to
maintain optimum working temperature; • Automatic temperature
control by electronic thermostat preventing the scorching of the
glue when the machine is idle; Glue tank (1,5 kg capacity) of solid
aluminum casting specially machined to leave the interior surface
of the glue pot even, with no edges and sharp angles to facilitate
the flow of the molten glue and its draining when cleaning cycle is
performed
PRESSURE ROLLER UNIT: A group of 3 rollers exerting pressure on
the edge band
mechanically in order to achieve its adhesion onto the panel
edge. The first roller
(cylindrical) is driven and the next two are conical (positive
&negative), of smaller diameter
and free running. The main pressure roller is positioned by a S
IKO digital counter to the
desired edge thickness from 0,4 to 2,0 mm;.
END TRIMMING UNIT V-7: (A carriage with 2 independent HF motors
(0,35 kW/12000
RPM), one performing the front and the other the rear trim
cut.
Soft and precise movement of the carriage on linear bearings
along hardened and ground
cylindrical bars.
T&b trimming unit JC-7(standard): Powered by two top and
bottom motors of H.F.
12.000 r.p.m and 0,35 Kw. e/o, for trimming of the excess of
edging material along the upper
and the lower edges of the panel. Horizontal and vertical
tracers with SIKO digital readouts
for easy and precise adjustment.
WORKPIECE TRA NSPORT A ND SUPPORT: Drag chain – an industrial
chain sliding
on two hardened and ground steel guides and pads with non-stick
rubber cushions. Pressure
beam with 2 rows of rollers. Two working speeds: 9 / 14 m/min.
Motorized pressure beam
with positioning from the control panel according to the
thickness of the panel.
STANDARD CONFIGURATION OF THE MACHINE:
� High Frequency motors controlled by independent electronic
converters;
� Control panel with integrated PLC and display;
� Dust collection system for all machining units;
� Pressure beam with 2 rows of rollers;
� Roller support extension for big work pieces;
� Hosing on the operating units for dust collecting
purposes;
WORKING STATIONS
CONTROL PANEL RAPID-1:
SCREEN OMRON 3,5” : The OMRON 3,5” touch-screen display is 3.5"
wide and has a direct connection with
the PLC allowing it to work in real time mode and monitor at any
moment the
current status of the machine.
All machine functions can be controlled from the display a nd
all features can
be easily accessed by the buttons (like editing programs,
modifying
parameters, visualizing alarms, machine star t/stop, checking
the PLC inputs
and outputs).
Up to 20 different job programs can be created, edited and
selected
