Upload
others
View
2
Download
0
Embed Size (px)
Citation preview
LED Down Light Can Retrofit FixtureImportant: Read all instructions prior to installation. DL56D-xW12W
User Manual
LED Down Light Can Retrofit
DL56D-xW12W
User Manual
Rev Date: V2 10/24/19Rev Date: V2 10/24/19
Recessed Housing Compatibility
• LED Retrofit Luminaire is designed to install in standard 5” or 6” recessed downlight housing.
• Compatibility of housing not on this list maybe determined by measurement of the housing as detailed in the attached drawing (Figure 1)
• This recessed luminaire has E26/27 Edison screw-base and is ETL Classified for installation in shallow recessed housing.
R e pla c in g L E D L u m in a ir e s :.With fingertips,pull down firmly on trim ring until module stops..Squeeze torsion springs together to remove LED module..Disconnect LED module wiring from recessed can (LED Connector or screw in Edison base.)
In s ta l la tio n i n to H o u s in g s :
W a r r a n ty :We offer 5 years limited warranty.As with any electrical
installation,a qualified electrician must ensure compatibility
of use with a particular housing;this includes all applicable
national and local electrical and building codes.Installer is
responsible to securely retain the LED Module in a housing
at time of installation.
FIG.4 FIG.5
FIG.2 FIG.3
1.Loosen torsion spring bracket with screw;If install into 6" can housings:Remove 2 torsion springbrackets completely to keep them in the out ward postion. (FIG.1-1)If install into 5" can housing: Slide bracket to inward position.(FIG.1-2)Then,Tighten screw.
5.Squeeze both torsion spring arms together and insertinto the torsion spring slots (or receiner bracktes) of thecan.Tuck all wires into the can and carefully push the retrofit trim into can (note:to provide enough room inshallow cans carefully position socket adapter andsocket adjacent to the long side of the LED driver priorto inserting the retrofit tirm into the can.(FIG.5)
4.Plug the female connector of the retrofit trim onto themale connector of the socket adapter assembly.(FIG.4)
3.Thread the socket adapter into the socket.(FIG.3)
2.Unscrew the wing nut inside the can , Upwards move the socket bracket to max from the can.(FIG.2)
P a c k in g L is t:1.LED luminaire(with LED Driver)2.18# Black/White connecting wire with E26 lamp holder (for L/N input)
The LED luminaire can be dimmed with many standard incandescent dimmers,however an electronic low voltage version of a standard dimmer (with neutral connection ) is recommended for many applications.Updates in dimmer technology and special conditions may apply depending on the dimmer type being used.To be assured of the latest information regarding luminaire and dimmer compatibility,please contact dimmer manufacturer.
D im m in g :
Downlight
DIMMER
GND
AC120
N
L
Downlight Downlight
FIG.1-1 FIG.1-2
6"
5"
5-6in c h
E26 SOCKET ADAPTER
LUMINAIRE
Dimmer Compatibility
Brand Lutron LevitonModel DVCL-153P-WH 6683
MACL-153M-WH 6672S-600PR-WH 6631
SPSLV-600-WH 6633-PDVLV-603P-IV 1A23O5MALV-600-IV 0B33K1
MALV-600DVW-603PGH-WH
4X603CTCL-153P
SLV-600P-WHCT-603PGNT-1000S-603P
DV-600PRA-6D
DL56D-xW12W
User ManualInstallation Instructions Install Into Housings:
Removing LED Luminaires:
Dimming:
LED Down Light Can Retrofit FixtureImportant: Read all instructions prior to installation.
1. Ensure mounting tabs on retrofit trim are extended all the way out before installation.
2. Thread socket adapter into socket (FIG.1)3. Plug female connector of fixture into the male connector of socket
adapter. (FIG. 2) 4. Tuck all wires into the can and carefully push the retrofit trim into
can To provide enough room in shallow cans carefully position socket adapter wiring to side of the LED driver prior to inserting the retrofit trim into the can. (FIG. 3)
1. With fingertips, twist trim ring clockwise and pull down on retrofit trim.
2. Disconnect fixture from socket adapter.3. Unscrew socket adapter from recessed can.
Rev Date: V2 10/24/19
Wiring Diagram
R e pla c in g L E D L u m in a ir e s :.With fingertips,pull down firmly on trim ring until module stops..Squeeze torsion springs together to remove LED module..Disconnect LED module wiring from recessed can (LED Connector or screw in Edison base.)
In s ta l la tio n i n to H o u s in g s :
W a r r a n ty :We offer 5 years limited warranty.As with any electrical
installation,a qualified electrician must ensure compatibility
of use with a particular housing;this includes all applicable
national and local electrical and building codes.Installer is
responsible to securely retain the LED Module in a housing
at time of installation.
FIG.4 FIG.5
FIG.2 FIG.3
1.Loosen torsion spring bracket with screw;If install into 6" can housings:Remove 2 torsion springbrackets completely to keep them in the out ward postion. (FIG.1-1)If install into 5" can housing: Slide bracket to inward position.(FIG.1-2)Then,Tighten screw.
5.Squeeze both torsion spring arms together and insertinto the torsion spring slots (or receiner bracktes) of thecan.Tuck all wires into the can and carefully push the retrofit trim into can (note:to provide enough room inshallow cans carefully position socket adapter andsocket adjacent to the long side of the LED driver priorto inserting the retrofit tirm into the can.(FIG.5)
4.Plug the female connector of the retrofit trim onto themale connector of the socket adapter assembly.(FIG.4)
3.Thread the socket adapter into the socket.(FIG.3)
2.Unscrew the wing nut inside the can , Upwards move the socket bracket to max from the can.(FIG.2)
P a c k in g L is t:1.LED luminaire(with LED Driver)2.18# Black/White connecting wire with E26 lamp holder (for L/N input)
The LED luminaire can be dimmed with many standard incandescent dimmers,however an electronic low voltage version of a standard dimmer (with neutral connection ) is recommended for many applications.Updates in dimmer technology and special conditions may apply depending on the dimmer type being used.To be assured of the latest information regarding luminaire and dimmer compatibility,please contact dimmer manufacturer.
D im m in g :
Downlight
DIMMER
GND
AC120
N
L
Downlight Downlight
FIG.1-1 FIG.1-2
6"
5"
5-6in c h
E26 SOCKET ADAPTER
LUMINAIRE
Specifications
DL56D-xW12WOperating Voltage Range 120 VACTotal Power Consumption 12 WBeam Angle 90 degreeOperating Temperature -22°–122° F(-30°–50° C)Dimmable Yes (TRIAC)Fixture Weight 0.4 lb (0.18 kg)
Included Parts
1 - LED Down Light Can Retrofit Fixture1 - E26/27 Socket Adapter
• Product should be installed and serviced in accordance with applicable national, state, and local building and electrical codes
• Do not use light if enclosure is broken. Ensure that supply power is turned off at fuse box or circuit breaker before installing or servicing fixture.
• Suitable for use in enclosed recessed luminaires.• Suitable for damp locations. Avoid direct contact with water and other liquids.• Clean with a soft damp cloth only—do not use any chemical cleaners.• Suitable for type IC or for type non-IC.
Safety and Notes
R e pla c in g L E D L u m in a ir e s :.With fingertips,pull down firmly on trim ring until module stops..Squeeze torsion springs together to remove LED module..Disconnect LED module wiring from recessed can (LED Connector or screw in Edison base.)
In s ta l la tio n i n to H o u s in g s :
W a r r a n ty :We offer 5 years limited warranty.As with any electrical
installation,a qualified electrician must ensure compatibility
of use with a particular housing;this includes all applicable
national and local electrical and building codes.Installer is
responsible to securely retain the LED Module in a housing
at time of installation.
FIG.4 FIG.5
FIG.2 FIG.3
1.Loosen torsion spring bracket with screw;If install into 6" can housings:Remove 2 torsion springbrackets completely to keep them in the out ward postion. (FIG.1-1)If install into 5" can housing: Slide bracket to inward position.(FIG.1-2)Then,Tighten screw.
5.Squeeze both torsion spring arms together and insertinto the torsion spring slots (or receiner bracktes) of thecan.Tuck all wires into the can and carefully push the retrofit trim into can (note:to provide enough room inshallow cans carefully position socket adapter andsocket adjacent to the long side of the LED driver priorto inserting the retrofit tirm into the can.(FIG.5)
4.Plug the female connector of the retrofit trim onto themale connector of the socket adapter assembly.(FIG.4)
3.Thread the socket adapter into the socket.(FIG.3)
2.Unscrew the wing nut inside the can , Upwards move the socket bracket to max from the can.(FIG.2)
P a c k in g L is t:1.LED luminaire(with LED Driver)2.18# Black/White connecting wire with E26 lamp holder (for L/N input)
The LED luminaire can be dimmed with many standard incandescent dimmers,however an electronic low voltage version of a standard dimmer (with neutral connection ) is recommended for many applications.Updates in dimmer technology and special conditions may apply depending on the dimmer type being used.To be assured of the latest information regarding luminaire and dimmer compatibility,please contact dimmer manufacturer.
D im m in g :
Downlight
DIMMER
GND
AC120
N
L
Downlight Downlight
FIG.1-1 FIG.1-2
6"
5"
5-6in c h
E26 SOCKET ADAPTER
LUMINAIRE
R e pla c in g L E D L u m in a ir e s :.With fingertips,pull down firmly on trim ring until module stops..Squeeze torsion springs together to remove LED module..Disconnect LED module wiring from recessed can (LED Connector or screw in Edison base.)
In s ta l la tio n i n to H o u s in g s :
W a r r a n ty :We offer 5 years limited warranty.As with any electrical
installation,a qualified electrician must ensure compatibility
of use with a particular housing;this includes all applicable
national and local electrical and building codes.Installer is
responsible to securely retain the LED Module in a housing
at time of installation.
FIG.4 FIG.5
FIG.2 FIG.3
1.Loosen torsion spring bracket with screw;If install into 6" can housings:Remove 2 torsion springbrackets completely to keep them in the out ward postion. (FIG.1-1)If install into 5" can housing: Slide bracket to inward position.(FIG.1-2)Then,Tighten screw.
5.Squeeze both torsion spring arms together and insertinto the torsion spring slots (or receiner bracktes) of thecan.Tuck all wires into the can and carefully push the retrofit trim into can (note:to provide enough room inshallow cans carefully position socket adapter andsocket adjacent to the long side of the LED driver priorto inserting the retrofit tirm into the can.(FIG.5)
4.Plug the female connector of the retrofit trim onto themale connector of the socket adapter assembly.(FIG.4)
3.Thread the socket adapter into the socket.(FIG.3)
2.Unscrew the wing nut inside the can , Upwards move the socket bracket to max from the can.(FIG.2)
P a c k in g L is t:1.LED luminaire(with LED Driver)2.18# Black/White connecting wire with E26 lamp holder (for L/N input)
The LED luminaire can be dimmed with many standard incandescent dimmers,however an electronic low voltage version of a standard dimmer (with neutral connection ) is recommended for many applications.Updates in dimmer technology and special conditions may apply depending on the dimmer type being used.To be assured of the latest information regarding luminaire and dimmer compatibility,please contact dimmer manufacturer.
D im m in g :
Downlight
DIMMER
GND
AC120
N
L
Downlight Downlight
FIG.1-1 FIG.1-2
6"
5"
5-6in c h
E26 SOCKET ADAPTER
LUMINAIRE
Dimming performance may depend on the dimmer, the dimmer range adjustment setting (for dimmers with brightness range adjustments), the wiring method, and/or the number of LED modules installed onto the dimmer circuit. For dimmer selection, Dimming control manufacturers revise their product often; for the latest list of compatible dimmers please visit our website.
For best results, it is recommended to install a minimum of four LED modules onto one dimmer. Before turning on the LED lights, set dimmer position at maximum before adjusting to a lower light level. Please follow the dimming control manufacturer’s instructions for the installation of all dimming controls.
We offer 5 years limited warranty. As with any electrical installation, a qualified electrician must ensure compatibility of use with a particular housing. This includes all applicable national and local electrical and building codes. Installer is responsible to securely install LED fixture into housing at time of installation.
Warranty Information
FIG 1
FIG 2 FIG 3
5yr
ETL CLASSIFIED