Quick Start Guide(V200R002C00_01)

Huawei AR200-S Series Enterprise RoutersV200R002C00

Quick Start Guide

Issue 01

Date 2011-12-30

HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior writtenconsent of Huawei Technologies Co., Ltd. Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.All other trademarks and trade names mentioned in this document are the property of their respective holders. NoticeThe purchased products, services and features are stipulated by the contract made between Huawei and thecustomer. All or part of the products, services and features described in this document may not be within thepurchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,and recommendations in this document are provided "AS IS" without warranties, guarantees or representationsof any kind, either express or implied.

The information in this document is subject to change without notice. Every effort has been made in thepreparation of this document to ensure accuracy of the contents, but all statements, information, andrecommendations in this document do not constitute the warranty of any kind, express or implied.

Huawei Technologies Co., Ltd.Address: Huawei Industrial Base

Bantian, LonggangShenzhen 518129People's Republic of China

Website: http://www.huawei.com

Email: [email protected]

Issue 01 (2011-12-30) Huawei Proprietary and ConfidentialCopyright © Huawei Technologies Co., Ltd.

i

http://www.huawei.com

mailto:[email protected]

About This Document

Intended AudienceThis document provides an overall description of the AR200-S, details about each chassis andboard, cables available to the device, lists of components and basic configuration.

This document is intended for:

l Network planning engineers

l Hardware installation engineers

l Commissioning engineers

l On-site maintenance engineers

l System maintenance engineers

Symbol ConventionsThe symbols that may be found in this document are defined as follows.

Symbol Description

DANGERIndicates a hazard with a high level of risk, which if notavoided, will result in death or serious injury.

WARNINGIndicates a hazard with a medium or low level of risk, whichif not avoided, could result in minor or moderate injury.

CAUTIONIndicates a potentially hazardous situation, which if notavoided, could result in equipment damage, data loss,performance degradation, or unexpected results.

TIP Indicates a tip that may help you solve a problem or savetime.

NOTE Provides additional information to emphasize or supplementimportant points of the main text.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide About This Document


ii

Change HistoryChanges between document issues are cumulative. Therefore, the latest document issue containsall the changes in previous issues.

Changes in Issue 01 (2011-12-30)Initial commercial release.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide About This Document


iii

Contents

About This Document.....................................................................................................................ii

1 AR200-S Overview........................................................................................................................11.1 Naming Rule.......................................................................................................................................................21.2 Device Structure.................................................................................................................................................21.3 Indicator Description..........................................................................................................................................31.4 Physical Specifications.......................................................................................................................................6

2 Installation Product.......................................................................................................................82.1 Installation Preparations.....................................................................................................................................92.2 Installing the Device...........................................................................................................................................92.3 Connecting Device...........................................................................................................................................142.4 Powering on the Device....................................................................................................................................15

3 Logging In to the Router............................................................................................................173.1 Logging In to the Router Through the Console Port........................................................................................183.2 Logging In to the Router Using Telnet.............................................................................................................20

4 Connecting to the Internet.........................................................................................................214.1 Connecting to the Internet Using an xDSL Interface.......................................................................................224.2 Connecting to the Internet Through an Ethernet Interface...............................................................................24

5 How to Obtain Documentation and Technical Support......................................................27

6 FAQs...............................................................................................................................................28

Huawei AR200-S Series Enterprise RoutersQuick Start Guide Contents


iv

1 AR200-S Overview

About This Chapter

This section describes the naming rule, appearance and structure, indicators, and physicalspecifications of the AR200-S.

1.1 Naming RuleThis section describes the meanings of the AR200-S names.

1.2 Device StructureThis section describes the structure of the AR200-S.

1.3 Indicator DescriptionThis section describes the indicators on the AR200-S front panel.

1.4 Physical SpecificationsThis section describes the physical specifications and system configuration of the AR200-S.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 1 AR200-S Overview


1

1.1 Naming RuleThis section describes the meanings of the AR200-S names.

Figure 1-1 shows the AR200-S naming rule.

Figure 1-1 AR200-S Naming rule

【AR】【B1 B2 B3 B4】【C1】【-D1】

AR 207 - S Example:

Table 1-1 explains the AR200-S naming rule.

Table 1-1 AR200-S naming rule

Field Description

B1 0 (AR200-S): indicates a low-end case-shaped product.

B2 Fixed at 2, indicating an enterprise access router.

B3 Fixed as 0, indicating a case-shaped product that does not providesubcards.

B4 When B1 is 0, B4 indicates the type of the fixed uplink interfaces onthe AR200-S (enterprise access gateway). The meanings of B4 valuesare:l 1: FE/GEl 7: ADSL-A

C1 C1 consists of one or two uppercase letters.l W: WLANl V: voice

D1 l A: AC power supply (This is the default configuration. You canchange the power type based on the actual requirements.)

l D: DC power supplyl S: small office and home office (SOHO)

1.2 Device StructureThis section describes the structure of the AR200-S.



2

Figure 1-2 shows the AR200-S models.

Figure 1-2 AR200-S models

AR200-SSeries

Product Series Model WAN

PortLAN Port Appearance

AR201-S 1 FE 8 FE

AR207-S

8 FE1ADSL2+AnnexA/M

1 2 4 53

76

1

2

4 53

76

1: CON/AUX port 2: WAN port

l AR201-S: WAN FEl AR207-S: ADSL

3: LAN FE port

AR201-S and AR207-S: 8FE ports

NOTEFE0 can be used as a WAN portso that double WAN ports canbe provided.

4: RESET

CAUTIONThe Reset button is used forresetting the device manually.

l Press and hold down: Restorethe Factory Settings.

l Press: Reset the system.

Resetting the device will causeservice interruption; therefore,confirm the action before you resetthe device.

5: DC power jack

NOTEThe AR200-S is powered by a 12V external power adapter .

6: Silkscreen

7: Ground screw

1.3 Indicator DescriptionThis section describes the indicators on the AR200-S front panel.



3

Indicators

The indicators on the AR200-S front panels vary according to the product models. Table 1-2lists the indicator differences.

Table 1-2 AR200-SIndicator differences

Difference Description

WAN port silkscreen l AR201-S: WAN FEl AR207-S: ADSL

Indicator DescriptionNOTE

l The front panels of AR201-S and AR207-S are the same except for the WAN port indicator silkscreen.

Figure 1-3 AR201-S front panel

1 2 3 4 5 6 7

8

Figure 1-4 AR207-S front panel

21



4

Table 1-3 Indicator description

Number

Indicator Color Description

1 PWR Green If the indicator is steady on, the system powersupply is normal.If the indicator is off, no system power supply isavailable.

2 SYS Red andgreen

If the indicator blinks green once every 2s (0.5Hz), the system is running properly.If the indicator blinks green once every 0.25s (4Hz), the system is powering on or restarting.

If the indicator is red, a fault that affects serviceshas occurred and cannot be rectifiedautomatically. The fault needs to be rectifiedmanually.

If the indicator is off, the software is not runningor is being reset.

3 USB Red andgreen

If the indicator is green, devices have beendeployed by using the USB disk.

If the indicator blinks green, the router is beingdeployed using the USB disk.

If the indicator is red, the router is failed to bedeployed using the USB disk.

If the indicator is off, the USB disk is not inserted,the USB interface fails, or the indicator fails.

4 PPP Green If the indicator is steady on, a PPP connection isset up.If the indicator is off, no PPP connection is set up.

5 VPN Green If the indicator is steady on, the VPN service isavailable.If the indicator is off, the VPN service isunavailable.

6 LINK Green If the indicator is steady on, a link is connected tothe WAN port.If the indicator is off, no link is connected to theWAN port.

ACT Green If the indicator blinks green, the WAN port istransmitting or receiving data.If the indicator is off, the WAN port is nottransmitting or receiving data.



5

Number

Indicator Color Description

7 LAN green If the indicator is steady on, a link is connected tothe LAN port.

If the indicator blinks green, the LAN port istransmitting or receiving data.

If the indicator is off, no link is connected to theLAN port.

8 USB port -

NOTE

l Number 6 : The WAN port indicators have different silkscreens (such as WAN FE and ADSL).

l Number 7 : FE0 can be used as a WAN port so that double WAN ports can be provided.

1.4 Physical SpecificationsThis section describes the physical specifications and system configuration of the AR200-S.

Table 1-4 Physical specifications

Item Description

Dimensions (width x depth x height) Without rack-mounting ears installed: 300.0 mm x216.4 mm x 44.0 mmWith rack-mounting ears installed: 482.6 mm x216.4 mm x 44.0 mm

Maximum power consumption l AR201-S: 12.5 Wl AR207-S: 15.6 W

Weight 2.2 kg

Operating temperature 0°C-40°C

Relative humidity 5% RH to 90% RH, non-condensing

Altitude 0 m-3000 m

AC inputvoltage

Rated voltage 100 V AC-240 V AC, 50/60 Hz

Maximum voltagerange

90 V AC-264 V AC, 47/63 Hz



6

Table 1-5 System configuration

Product Name Processor Memory Flash Memory

AR201-S Dual-core 533 MHz 512 MB 512 MB

AR207-S Dual-core 533 MHz 512 MB 512 MB



7

2 Installation Product

About This Chapter

This section describes the method of installing and connectingAR200-S series products.

2.1 Installation PreparationsThis section lists the tools and accessories for installing the AR200-S.

2.2 Installing the DeviceThis section describes AR200-S installation scenarios and installation methods.

2.3 Connecting DeviceThis section describes how to connect AR200-S series products.

2.4 Powering on the DeviceThis section provides the checklist used to check the AR200-S before powering on it.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 2 Installation Product


8

2.1 Installation PreparationsThis section lists the tools and accessories for installing the AR200-S.

Tools

Claw hammer Utility knife COAX crimping tool

Diagonal pliers RJ45 crimping tool Wire stripper

Network cable tester Multimeter Measuring tape

Ladder Hammer drill Vacuum cleaner

ESD wrist strap Level Floating nut mounting bar

Flat-head screwdriverPhilips screwdriverMarker pen

Accessories

Rubber pad Floating nut M4 screw: fixes brackets to chassis

M6 screw: fixes chassis into cabinet Bracket Ground cable

2.2 Installing the DeviceThis section describes AR200-S installation scenarios and installation methods.



9

NOTE

All AR200-S series products have the same installation scenarios, installation methods, and cableconnections. This section uses AR207-S as an example.

Placing Chassis on the DesktopBefore placing the AR200-S on the desktop, attach rubber pads onto each of the four recessedcorner areas on the bottom of the chassis.

AR207-S

Wall-Mounting the Chassis

CAUTIONl When wall-mounting the AR200-S, do not attach rubber pads to the chassis. If the rubber

pads have been attached, remove them.l It is inconvenient to connect ground cables and network cables after mounting the AR200-

S chassis on the wall. Therefore, it is recommended that you connect cables before mountingthe chassis on the wall. If the chassis has been mounted on the wall, hold the chassis whenconnecting cables, preventing it from being detached from the wall. For the method ofconnecting cables, see 2.3 Connecting Device.

l When connecting cables, do not make the front plastic panel of the chassis touch the groundto avoid damage.

l It is recommended that you wall-mount the AR200-S with its front panel (with indicators)facing up and its rear panel (with interfaces) facing down.

l Use a ladder when mounting the chassis on the wall.

1. Use the template on the last page to mark the location for the two mounting screws and theupper, left, and right edges of the chassis on the wall.



10

2. The diameter of the mounting screws is 4 mm. Choose an appropriate drill bit accordingto the diameter of the mounting screws. Hammer the hollow wall anchors into the drilledholes. Screw the mounting screws into the wall anchors using a screwdriver. Leave thescrews protruding 2 mm from the wall.

3. Mount the chassis by aligning the mounting brackets on the back of the AR200-S usingmounting screws.



11

4. Connect the power adapter. Place the power adapter on a nearby horizontal surface, but donot hang it under the equipment.

Installing the Chassis in a Cabinet or Rack

CAUTIONl When installing the AR200-S in a cabinet or rack, do not attach rubber pads to the chassis.

If the rubber pads have been attached, remove them.l The guide rails or trays are not necessary for the installation in a cabinet or rack because the

AR200-S chassis can be fixed by rack-mounting brackets. Customers need to buy the rack-mounting brackets.

l It is recommended that you install the AR200-S with its front panel (providing indicators)facing inside and its rear panel (providing interfaces) facing outside.

l Ensure that the air exhaust vent is not obstructed in any way. Otherwise, the chassis mayoverheat.

1. Install two rack-mounting brackets. It is recommended that you install the rack-mountingbrackets close to the rear panel (providing interfaces).

2. Install two floating nuts on each side of the rack. The AR200-S chassis is 1 U high. Themounting holes located on the rack-mounting brackets will be fixed to two mounting holeson the rack.



12

Floating nut mounting bar

3. Raise and hold the chassis by hands and move the chassis into the cabinet. Insert the panelscrews into the below floating nuts and keep a 2 mm space between the screws and mountingbar. Insert the rack-mounting ear pre-installation holes into the space.

2mm

AR207-S

4. Hold the chassis with one hand while using the other hand to secure the lower panel screwand then the upper one with a screwdriver.



13

AR207-S

2.3 Connecting DeviceThis section describes how to connect AR200-S series products.

Figure 2-1 Connecting the AR200-S to network

3

1

2

4

5

a b



14

1: Console cable

l The 8-pin RJ45 connector is inserted into the console port (CON/AUX port) of the AR200-S.

l The DB9 male connector is connected to the maintenance terminal, such as a computer.

2: WAN port cable that connects the AR200-S to the upper-layer network

l On an AR201-S router, an FE port functions as the WAN port and connects to a networkcable with RJ45 connectors.

l On an AR207-S router, an ADSL port functions as the WAN port and connects to a networkcable with RJ11 connectors.

3: LAN port cable, which is connected to a computer with a network cable (RJ45 connectors).

4: Ground cable. The M4 connector is connected to the AR200-S and the M6 connector isconnected to ground. The cable is in yellow and green.

l When the AR200-S is placed on the desktop or installed in a cabinet/rack, the ground cableis connected facing downwards, as shown in Figure 2-1 a. The ground cable cannotinterfere with other devices in the cabinet/rack.

l When the AR200-S is wall mounted, the ground cable is connected facing left, as shownin Figure 2-1 b.

5: external power adapter, which is connected to the AC power supply to output DC power tothe device.

Power adapter output power:l AR200-S series: 36W

NOTEThe AC power cable must be secured using a latch.

2.4 Powering on the DeviceThis section provides the checklist used to check the AR200-S before powering on it.

Checklist

No. Item Method

1 The power cables and ground cables are copper wires, andare not spliced or damaged. The cables are safelyconnected and in compliance with standards.

View

2 The power cables and ground cables are connected safely.The spring washers of the ground cable terminals are onthe flat washer.

View

3 All signal cables to be deployed pass the continuity check. Measure

4 No signal cables are near the cabinet's heat vents. View



15

No. Item Method

5 The bent part of signal cables cannot be too tight. View

6 The cables in the cabinet are not crossed and the cablesoutside the cabinet are bundled.

View

7 Both ends of signal cables are clearly labeled and the labeltext is in the same direction.

View

8 Newly added devices will not cause a loop on the network.For example, a newly added device cannot be connectedto another device using two links.

View thenetworkingdiagram

Checking the AR200-S After Power-onNOTE

l After powering on the AR200-S, view the PWR and SYS indicators. The two indicators are the sameon all the AR200-S routers, and AR207-S is used as an example here.

l For details about the indicators on AR200-S, see 1.3 Indicator Description.

CAUTIONDo not frequently power on and off the device.

21

After powering on the AR200-S, check the following indicators.

No. Silkscreen Status

1 PWR If the indicator is green, the system power supply is normal.

2 SYS If the indicator blinks green once every 2s (0.5 Hz), the systemis running properly.



16

3 Logging In to the Router

About This Chapter

After the router is powered on, you can log in to the router.

3.1 Logging In to the Router Through the Console PortThis section describes how to log in to the router through the console port.

3.2 Logging In to the Router Using TelnetThis section describes how to log in to the router using Telnet.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 3 Logging In to the Router


17

3.1 Logging In to the Router Through the Console PortThis section describes how to log in to the router through the console port.

Procedure

Step 1 Connect the router to a PC using a Console Cable. Connect the RJ45 connector of the cable tothe console port of the router, and connect the DB9 connector to the serial port of the PC.

Step 2 Run the terminal emulation program on the PC. For example, to open the HyperTerminal ofWindows XP on the PC, choose Start > Programs > Accessories > Communications >HyperTerminal. Enter the name of the new connection in the Name text box and click OK, asshown in Figure 3-1.

Figure 3-1 Creating a connection

Step 3 Select the console port used and click OK, as shown in Figure 3-2.



18

Figure 3-2 Selecting the console port

Step 4 Click Restore Defaults and click OK, as shown in Figure 3-3.

Figure 3-3 Setting communication parameters



19

Step 5 Press Enter on the subsequent dialog boxes until the command line prompt of the user view,such as <Huawei>, is displayed.

You can run commands to configure the router. Enter a question mark (?) to see a list of availablecommands.

----End

3.2 Logging In to the Router Using TelnetThis section describes how to log in to the router using Telnet.

Procedure

Step 1 Connect a PC to any LAN port of the router with a network cable.

Step 2 Configure an IP address for the PC. The IP address must be on the network segment192.168.1.0/24, but cannot be 192.168.1.1.

After the configuration is complete, run the ping 192.168.1.1 command on the PC to checkwhether the router can be pinged successfully. If the ping operation succeeds, the connectionhas been set up successfully. If the ping operation fails, the connection failed to be established.Check whether the network cable is working properly. If not, replace the network cable.

Step 3 Access the command line window on the PC. For example, if the PC runs Windows XP, chooseStart > Run and enter cmd in the displayed dialog box.

Step 4 Run the telnet 192.168.1.1 command to log in to the router.

Step 5 Enter the default user name and password admin. If the user interface is displayed, you loggedin successfully.

When you log in for the first time, the following information is displayed:

Username:adminPassword:

<Huawei>

----End



20

4 Connecting to the Internet

About This Chapter

This section describes how to enable users to connect to the Internet through the router.

Select the network access mode based on the link type of uplink physical interfaces.

4.1 Connecting to the Internet Using an xDSL InterfaceThis section describes how to connect to the Internet using an xDSL interface.

4.2 Connecting to the Internet Through an Ethernet InterfaceThis section describes how to connect to the Internet through an Ethernet interface.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 4 Connecting to the Internet


21

4.1 Connecting to the Internet Using an xDSL InterfaceThis section describes how to connect to the Internet using an xDSL interface.

Networking Requirements

As shown in Figure 4-1, users connected to the router use the same account. The dialing functionis configured on the router so that users can connect to the Internet.

NOTE

The ADSL line is used as an example. The G.SHDSL line configuration is similar.

Figure 4-1 Connecting to the internet using an xDSL interface

InternetInternetInternetInternet

User1

User2

User3

Eth0/0/1

Eth0/0/2

Eth0/0/3

Atm0/0/0

DSLAM PPPoA server

Router

Table 4-1 Data plan

Physical Interface Logical Interface IP Address

Eth0/0/1 VLANIF 1 (Eth0/0/1,Eth0/0/2, and Eth0/0/3 areLAN ports and belong toVLAN 1 by default)

The default IP address forVLANIF 1 is 192.168.1.1/24.

Eth0/0/2

Eth0/0/3

ATM0/0/0 Dialer0 Dialer0 obtains an IP addressand the DNS server's IPaddress through ADSLdialing.

Configuration Roadmap1. Configure a dialer interface that obtains an IP address and the DNS server's IP address

through ADSL dialing.2. Configure the router as the PPPoA client. The router connects to the Internet through the

PPPoA server.3. Configure the DHCP server function.



22

Procedure

Step 1 Configure a dialer interface and ACL.<Huawei> system-view[Huawei] sysname Router[Router] dialer-rule[Router-dialer-rule] dialer-rule 10 ip permit[Router-dialer-rule] quit[Router] acl 2000 [Router-acl-basic-2000] rule 5 permit source 192.168.1.0 0.0.0.255[Router] interface dialer 0

NOTE

If a private address is used, configure an ACL referenced by NAT.

Step 2 Configure a dialer user. Obtain the user name and password from the carrier.

NOTE

Ensure that group-number in the dialer-group command is the same as group-number in the dialer-rulecommand.

Both ends must use the same PPP authentication mode.[Router-Dialer0] dialer user adsluser1[Router-Dialer0] dialer-group 10[Router-Dialer0] dialer bundle 12[Router-Dialer0] dialer number 6666[Router-Dialer0] ip address ppp-negotiate[Router-Dialer0] ppp chap user adsluser1[Router-Dialer0] ppp chap password simple huawei[Router-Dialer0] nat outbound 2000[Router-Dialer0] quit

Step 3 Configure the ATM interface.[Router] interface atm 0/0/0[RouterA-Atm0/0/0] pvc pppoa 2/40[RouterA-atm-pvc-Atm0/0/0-2/40-pppoa] map ppp dialer 0[RouterA-atm-pvc-Atm0/0/0-2/40-pppoa] quit[RouterA-Atm0/0/0] quit

Step 4 Configure a static route to the PPPoA server.[Router] ip route-static 0.0.0.0 0.0.0.0 dialer 0

# Run the display interface dialer command to check whether the dialer interface has beenassigned a correct IP address.

<Router> display interface Dialer 0

The following information indicates that the dialer interface has been assigned a correct IPaddress.

Step 5 Configure the DHCP server function so that users can automatically obtain IP addresses fromthe router.

# Configure the DHCP server function.

<Router> system-view[Router] dhcp enable[Router] interface vlanif 1[Router-Vlanif1] dhcp select interface

Step 6 Verify the configuration.



23

Users can access the Internet and obtain IP addresses in the range of 192.168.1.2 to192.168.1.254.

----End

Configuration FilesConfiguration file of the Router

# sysname Router# dhcp enable#acl number 2000 rule 5 permit source 192.168.1.0 0.0.0.255#dialer-rule dialer-rule 10 ip permit # interface Dialer0 ppp chap user adsluser1 ppp chap password simple huawei ip address ppp-negotiate ppp ip dns admit-any dialer user adsluser1 dialer bundle 12 dialer number 6666 dialer-group 10 nat outbound 2000# interface Atm0/0/0 pvc pppoa 2/40 map ppp dialer 0#interface Vlanif1 dhcp select interface # ip route-static 0.0.0.0 0.0.0.0 Dialer0#return

4.2 Connecting to the Internet Through an EthernetInterface

This section describes how to connect to the Internet through an Ethernet interface.

Networking RequirementsAs shown in Figure 4-2, the router functions as the PPPoE client and connects user devices tothe PPPoE server. The user devices use the same user account. If the account is successfullyauthenticated by the PPPoE server, a PPPoE session is established.

The router obtains an IP address from the PPPoE server. The user devices can be assigned staticIP addresses on the network segment 192.168.1.0/24 or obtain dynamic IP addresses from therouter (DHCP server).



24

Figure 4-2 router functions as the PPPoE client

Host 1

Host 2

Host n

Eth0/0/8

PPPoE Client PPPoE Server

Eth0/0/1InternetInternetInternetInternet

Configuration RoadmapThe configuration roadmap is as follows:

1. Create a dialer interface and set parameters for the dialer interface.2. Create a PPPoE session.3. Configure a static route from the router to the PPPoE server.

Data PreparationTo complete the configuration, you need the following data:l Parameters of the dialer interface, including the dialer interface number, dialer interface IP

address, dialer bundle, and idle-cut durationl Destination address, mask, and outbound interface of the static route

Procedure

Step 1 Configure the PPPoE server.Configure the authentication mode, IP address allocation mode, and IP address or IP addresspool for the PPPoE client. For details about the configuration procedure, see the documentationof the PPPoE server.

Step 2 Configure a dialer interface on the router.<Huawei> system-view[Huawei] sysname Router[Router] acl 2000 [Router-acl-basic-2000] rule 5 permit source 192.168.1.0 0.0.0.255 [Router] dialer-rule[Router-dialer-rule] dialer-rule 1 ip permit[Router-dialer-rule] quit[Router] interface dialer 0[Router-Dialer0] dialer user ethuser2[Router-Dialer0] dialer-group 1[Router-Dialer0] dialer bundle 1[Router-Dialer0] ppp chap user 12345678910[Router-Dialer0] ppp chap password cipher user1[Router-Dialer0] ip address ppp-negotiate



25

[Router-Dialer0] nat outbound 2000[Router-Dialer0] quit

NOTE

If a private address is used, configure an ACL referenced by NAT.

Step 3 Create a PPPoE session.[Router] interface ethernet 0/0/8[Router-Ethernet0/0/8] pppoe-client dial-bundle-number 1 on-demand[Router-Ethernet0/0/8] quit

Step 4 Configure a static route from the router to the PPPoE server.[Router] ip route-static 0.0.0.0 0.0.0.0 24 dialer 0

Step 5 Verify the configuration.

Run the display pppoe-client session summary command to check the PPPoE session statusand configuration. The following information shows that the PPPoE session status is Up and thesession configuration is correct.

<Huawei> display pppoe-client session summaryPPPoE Client Session:ID Bundle Dialer Intf Client-MAC Server-MAC State1 1 1 Eth0/0/8 00e0fc030201 00e0fc030201 UP

----End

Configuration FilesConfiguration file of the Router

# sysname Router## acl number 2000 rule 5 permit source 192.168.1.0 0.0.0.255# dialer-rule dialer-rule 1 ip permit #interface Dialer0 link-protocol ppp ip address ppp-negotiate dialer user user2 ppp chap user 12345678910 ppp chap password cipher user1 dialer-group 1 dialer bundle 1 nat outbound 2000#interface Ethernet0/0/8 pppoe-client dial-bundle-number 0# ip route-static 0.0.0.0 0.0.0.0 Dialer0#return



26

5 How to Obtain Documentation andTechnical Support

This section describes how to obtain documentation and technical support.

Obtaining DocumentationVisit http://support.huawei.com and choose Data Communication > Product > Router >Prodcut Type > Product Manual to obtain corresponding documentation.

NOTE

You can select different values of Product Type. For example, to query the AR200-S documentation, selectAR200-S.

The web site provides files in .pdf and .hdx format. You can view a single manual in web formatonline. Equipment users can browse the Hedex package after logging to the web site. Select therequired documentation.

It is recommended that you use the email address to request the equipment user name andpassword. If you have any questions, contact the Huawei technical personnel.

Obtaining Huawei Technical SupportIf you have trouble in locating or rectifying faults during maintenance or troubleshooting byfollowing instructions in this document, contact the Huawei customer service center (CSC) forhelp.

l Email: [email protected]

You can also visit http://support.huawei.com, click Contact Us in the lower area of the page,and select the country to obtain contact information about Huawei local office.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 5 How to Obtain Documentation and Technical Support


27

6 FAQs

This section describes the frequently asked questions about the router.

Why Is the Power Supply Indicator Off?The possible causes are as follows:

l The router is powered off.l The power supply is powered off.l The power cable is connected incorrectly.l The power supply does not adapt to the router.

How Do I Restore Factory Settings?Hold the RESET button for more than 5s.

CAUTIONThe user-defined configurations will be lost when you restore factory settings.

What Are the Default Configurations?The default configurations are as follows:

l The management IP address is 192.168.1.1/24, which is allocated to VLANIF 1. All LANports belong to VLAN 1.

l A super administrator is provided, which is a level-3 user with the user name and passwordas admin. You can log in as the admin user using Telnet.

What Can I Do If I Forget the User Name or Password?Perform one of the following operations:

l Restore factory settings. The default user name and password are admin. The user-definedconfigurations will be lost when factory settings are restored.

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 6 FAQs


28

l Log in to the router through the console port and run the display current-configurationcommand to check the user-defined authentication mode.

Table 6-1 Follow-up Procedure

Password Mode Follow-up Procedure

Plain-text password Obtain the user name and password in the displaycurrent-configuration command output. local-user admin password simple adminThe preceding information shows that the user name isadmin and the password is admin. local-user admin service-type telnetTelnet users must use the user name admin and passwordadmin to log in to the router.

Cipher-text password Configure a new password matching the user name. Youcan use the new user name and password to log in to therouter.# local-user huawei password ciper N`C55QK<`=/Q=^Q`MAF4<1!! local-user huawei service-type telnet # In the preceding example, the user names of the Telnetusers are huawei and their passwords are in cipher text.Run the following commands to set the passwords of thehuawei users to huawei.<Huawei> system-view[huawei] aaa[huawei-aaa] local-user huawei password simple huawei[huawei-aaa] quit

Huawei AR200-S Series Enterprise RoutersQuick Start Guide 6 FAQs


29

Documents

Quick Start Guide(V200R002C00_01)