Quick Start Guide～ for Flat Screen ~

March 2013

CASIODual Projection System

XJ-SK600/SK650

Quick Start Guide 　

This Quick Start Guide is for quick setup reference.For more detailed information about setup and operation Please refer to complete product manuals available forFree download on our website. http://support.casio.com/manuallist.php?rgn=1&cid=007

Information

Preparation 　

XJ-SK600/650 Screen 　

The purpose of this guide is to allow the user to set up the XJ-SK600/650 quicklyGuide also includes all basic information needed forflat Image alignment in the tabletop configuration.

60inch 　　

Tools needed - Phillips head screwdriver

Overview

Initial Projector Settings 　 Page 1

Projector Settings A&B

1.Plug in (only) Projector A.

2.Set the menu of Projector A * language: English or other language * INPUT: HDMI * Auto Keystone: off * Keystone Correction: 0 * Auto Power Off: off * Signal Name Indicator: off * No Signal Screen: black * Direct Power On: off ( When you will use ceiling position…) *Ceiling mount :on3.Power off projector A

4.Plug in only projector B (un-plug Projector A)

5.Set menu of projector B as listed in step 2.6.Power off projector B

Use The Projector Remote for Initial Menu Settings

Hardware Settings

Projector A

Projector B

Connect to Projector A HDMI & RS232C

Connect to Projector B HDMI & RS232C

Connect to AC AdapterPower cable

to AC AdapterEach Power cable

Geometric correction Box YA-S10

Install the 4 included feet for Table Top Setup

Shut down using POWER BUTTON to retain all settings in memory.

Once menu settings are completed youAre finished using the projector remote.

Geometric Image Correction OverviewPage 2

　 Aligning the Position of Both Images 　

1. Position the SK600/SK650 so it is aligned with the screen.2. Make Menu Adjustments on each projector3. Power on all devices using the YA-S10 of remote control4. Select “Shaping type” （ Flat ）　　 Correct 　→　 Shaping type +Enter key 　→　 Flat + Enter key

5. Adjust Image Positions , Zoom and Focus (adjust so that both colored images overlap closely Adjust the movable projector by loosening the side screws and turning center adjustment. Toggle Colors with A/B Button on the remote

6. Make final adjustments to Corners, Sides and Center.

Finish ( ESC button)

* When setting up the SK600/SK600, align with screen as pictured below.

Center

Screw

(All Image adjustments are made using the YA-S10 Remote Control)

Geometric Correction Details Page 3

　 Aligning the Position of Both Images 　

*The closer the 2 images are aligned during this step the smaller final adjustments will be needed.

7. Select “Corner Correction” (4 corner adjustment)

Explanation of keys.Correct 　 ：　 fast （ 8-arrow ）　⇔　 slow （ 4-arrow ）Position 　 ：　 Move position ( Up / Down / Left / Right)A⇔B 　　　 ： Toggle Image A (yellow) with projector B (Blue)Image 　　　：　 Change PC image with grid moveESC 　　　 ：　 Escape to “Image shaping” from grid mode　

Good No Good

Align single Yellow line inside Blue double lines using arrow keys

It’s Important to start with good corner alignment

Geometric Correction 3 Page 4

Aligning the Position of Both Images 　

8. Select Side Correction (Arch) Finish (ESC) Back to menu

10. Select Center Point Correction (Repeat alignment process) Finish (ESC)

Complete!

- END -

9. Select Side Correction (Parallel Shift) (Repeat alignment process) 　 Finish (ESC)

11. Set Screen aspect to (Automatic) Finish (ESC)

12. Select a single or double menu to be visible on screen

Once all alignment settings are completed connect contentSource (PC, DVD, Media Player) to control box input and run content