Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
www.dfi.com
1
USB 3.0
COM 1 COM 2 COM 4/8-bit DIOHDMI
Reset
Power
AntennaHole
AntennaHole HDD LED
Status LED
AntennaHole
COM 3 VGA*
DC-in
LAN 1 LAN 2USB 2.0
Grounding
Quick Installation GuideEC700-BT
DFI reserves the right to change the specifications at any time prior to the product's release. This QIG may be based on editions that do not resemble your actual products. For the latest revision and more details of the installation procedure, please refer to go.dfi.com/EC700-BT or scan the QR code on the right.
Panel
Front View
Back View
Note:This port can be in VGA or DVI-I.
• EC700-BT System Unit
• Screw pack for SATA drive installation
• Screw pack for Mini PCIe installation
Package Contents
2Quick Installation Guide |
Installing a 2.5" SATA Drive1. Locate the SATA drive bay on the system board. Unplug the SATA power and data cable, and
remove the 4 mounting screws that secure the HDD bracket to the system board.
2. Connect the SATA cable to the SATA drive first before affixing the SATA HDD on the bracket. Align the mounting holes of the SATA drive with the mounting holes on the HDD bracket and use the 3 provided mounting screws to secure the drive in place. Note that you should install the drive by affixing only 3 screws to the desired screw holes indicated in the picture below.
Mounting Screws (4x)
SATA drive baySATA power cable
SATA data cable
Mounting Screws (3x)
Mounting Screw
2.5" SATA drive
3
21
No Screw
3Quick Installation Guide |
3. Place the SATA drive with the HDD bracket back into the chassis. Secure the SATA drive bay with the mounting screws you removed in step 1. Then connect the SATA data and power cable to the connectors on the system board.
Mounting Screw
SATA power cable
SATA power connector
SATA data cable
SATA connector
Mounting Screw
4Quick Installation Guide |
Board Layout and Jumper Settings
933-EC7000-010GA33134944
TOP BOTTOM
SATA 1
14 SATAPower
LAN 1
LAN 2
DDR3LDDR3LDDR3LDDR3L
Mini PCIe
COM 4
1210
31JP22 1
1
1
(JP20)(JP18)(JP17)
(JP21)
1 3
1210
COM 2
COM 1USB 0
USB 3.0
HDMI
Res
et
Power
3940
2 1
LVDS LCDPanel
DC-in
USB 2
USB 7
USB 1
USB 6
COM 3
Mic-in
1Battery
Buzzer
1
ChassisIntrusion
1Clear CMOS Data (JP24)
SPIFlashBIOS
eMMC(optional)
iTEIT8528E
Mini PCIe mSATA
MicroSD(optional)
1
System Fan
1
USB 0PowerSelect(JP5)
11
2 10
9
COM 6
1
10
9COM 5
1 1
USB 1-2Power Select (JP6)
USB 5-7 PowerSelect (JP7)
1
2 10
9
USB 5
(JP25)
USB 2.0
USB 2.0
(JP17)(JP20)
COM 4/DIO Select (JP22, JP21)
Digital I/O 0-3 Output State Digital I/O Power Select
Auto Power-on Select
1
(JP18)Digital I/O 4-7 Output State
1
VGA/DVI-I
4
SATA 2.0
DDR3LDDR3LDDR3LDDR3LDDR3L
Intel Atom
E3800 Series
IntelWGI210AT
NuvotonNCT6106D
ASMediaASM1442
IntelWGI210AT
SMSCUSB4604
SIM Card
NXPPTN3460
StandbyPower LED
Clear CMOS Data JP24 Normal (default) 1-2 On
Clear CMOS Data 2-3 On
Auto Power-on Select JP25 Power-on via power button (default) 1-2 On Power-on via AC power 2-3 On
Digital I/O Output State JP18 (DIO 4-7) JP20 (DIO 0-3) GND (default) 1-2 On +5V or +5V_standby 2-3 On
Digital I/O Power Select JP17 +5V_standby 1-2 On +5V (default) 2-3 On
COM 4/DIO Select JP21, JP22
COM 4 (default) 1-2, 4-5 7-8, 10-11 On
DIO2-3, 5-6 8-9, 11-12 On
USB Power Select: 0 (JP5), 1-2 (JP6), 5-7 (JP7) +5V_standby (default) 1-2 On
+5V 2-3 On
Note: You cannot use COM 4 and DIO at the same time. Please set up JP21 and JP22 together.