Industrial L2+ Multi-Port Full Gigabit

Managed Ethernet Switch

IGS-5225-4T2S/IGS-5225-4P2S/

IGS-5225-4UP1T2S/IGS-5225-8P4S/IGS-5225-8P2T2S

Quick Installation Guide

Table of Contents

1. Package Contents ...................................................................... 3

2. Requirements ............................................................................ 5

3. Wiring the Power Inputs ............................................................ 6

4. Terminal Setup .......................................................................... 8

4.1. Logging on to the Console ................................................... 9

4.2 ConfiguringIPaddress .......................................................10

5. Starting Web Management ........................................................12

5.1 LoggingintotheIndustrialManagedSwitch ........................12

5.2 SavingConfigurationviaWeb .............................................15

6. RecoveringBacktoDefaultConfiguration ...................................16

7. Customer Support ....................................................................19

3

1. Package ContentsThank you for purchasing PLANET L2+ Industrial Managed Switch,IGS-5225Series.Thedescriptionsofthesemodelsareasfollows:

RJ45 Ports PoE+ PortsUltra PoE Ports

SFP Ports

IGS-5225-4T2S 4 - - 2

IGS-5225-4P2S 4 4 - 2

IGS-5225-4UP1T2S 5 - 4 2

IGS-5225-8P4S 8 8 - 4

IGS-5225-8P2T2S 10 8 - 2

“Industrial Managed Switch” mentioned in this Quick InstallationGuidereferstotheabovefivemodels.

4

Open the box of the Industrial Managed Switch and carefullyunpack it. The box should contain the following items for each of thefivemodels:

IGS-5225-4T2S

IGS-5225-4P2S

IGS-5225-4UP1T2S

IGS-5225-8P4S

IGS-5225-8P2T2S

QuickInstallation Guide

DIN-rail Kit

Wall Mounting Kit

DB9 to RJ45,RS232Console Cable

RJ45 Dust Cap

5 5 6 9 11

SFP Dust Cap 2 2 2 4 2

If any of these are missing or damaged, please contact your dealerimmediately.Ifpossible,retainthecartonincludingtheoriginalpackingmaterials to enable you to repack theproduct in case there is aneedto return it to us for repair.

5

2. RequirementsThe Industrial Managed Switch provides remote login interface formanagement purposes. The following equipment is necessary for furthermanagement:

z Workstations runningWindows XP/2003/Vista/7/8/2008/10, MAC OSXor later, Linux,UNIX,orotherplatformsare compatiblewithTCP/IP Protocols.

z Workstations are installed with Ethernet NIC (Network InterfaceCard)

z SerialPortConnection(Terminal)

The above Workstations come with COM Port (DB9) or USB-to-RS232 converter.

The above Workstations have been installed with terminalemulator, such as Hyper Terminal included in Windows XP/2003,putty or tera term.

Serial cable -- one end is attached to the RS232 serial port,while theotherend to the consoleportof the IndustrialManagedSwitch.

z Ethernet Port Connection

Network cables -- Use standard network (UTP) cables with RJ45connectors.

The above PC is installed with Web browser and JAVA runtimeenvironment plug-in.

Note

ItisrecommendedtouseInternetExplorer8.0orabovetoaccesstheIndustrialManagedSwitch.

6

3. Wiring the Power InputsTheUpper Panel of the IndustrialManaged Switch comes with a DC inlet power socket andone6-contact terminal block. Please follow thesteps below to insert the power wire.

1.Insert positive/negative DC power wires into Contacts 1 and 2 forPower1,orContacts5and6forPower2.

IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-4UP1T2S: 48~56VDC

Input DC 48-56V

DI0 DI1 DO0 DO1 GND GND

DC1+

DC2Fault+

1A@24V

1 2 3 4 5 6

1 2 3 4 5 6

Figure 3-1: IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-4UP1T2S Upper Panel

IGS-5225-4T2S:12~48VDC,24VAC

InputDC12~48VAC 24VDC1 DC2Fault

V1-V1+ V2+ V2-1A@24V

1 2 3 4 5 6

Figure 3-2: IGS-5225-4T2S Upper Panel

7

2. Tighten the wire-clamp screws for preventing the wires from loos-ening.

1 2 3 4 5 6V+ V- V+ V-Power 1 Power 2

Positive(+)Pin Negative(-)Pin

IGS-5225 Series Pin1/5 Pin2/6

Note

The wire gauge for the terminal block should be in therange from 12 to 24 AWG.

8

4. Terminal SetupTo configure the system, connect a serial cable to aCOM port on a PCornotebookcomputerandtoRJ45typeserial(console)portof theIndustrialManagedSwitch.Theconsoleportof the IndustrialManagedSwitch is DCE already, so that you can connect the console portdirectlythroughPCwithouttheneedofnullmodem.

PC/Workstationwith

Terminal emulation software

RJ45 to DB9 RS232 CableSerial Port

IP Address:192.168.0.100

IGS Industrial Managed Switch

Aterminalprogram is required tomake thesoftwareconnected to theIGS-5225seriesIndustrialManagedSwitch.

1. Run terminal program on the OS.

2.When the following screen appears, make sure that the COM portshouldbeconfiguredas:

z Baud:115200

z Parity:None

z Databits:8

z Stopbits:1

z Flowcontrol:None

9

4.1. Logging on to the ConsoleOnce the terminal has been connected to the device, power on theIndustrialManagedSwitchandtheterminalwilldisplay“runningtestingprocedures”.

Note

The following terminal configuration of the IGS-5225-4UP1T2S is taken for an example.

Then, the followingmessage asks to log in user name and password.The default user name and password are shown as follows and thelogin screen in Figure 4-1 appears

Username:adminPassword: admin

Figure 4-1: Console Login Screen

Theuser cannowenter commands tomanage the IndustrialManagedSwitch.Foradetaileddescriptionofthecommands,pleaserefertothefollowing chapters.

Note

1. For security reason,please change and memorize the new password after this first setup.

2. Only accept command in lowercase letter underconsole interface.

10

4.2 ConfiguringIPaddressThe Industrial Managed Switch is shipped with default IP addressshownbelow:

IPAddress:192.168.0.100SubnetMask:255.255.255.0

To check the current IP address or modify a new IP address for theSwitch,pleaseusetheprocedureasfollows:

Display of the current IP Address

1. At the “#”prompt,enter “show ip interface brief”.

2.ThescreendisplaysthecurrentIPaddressshowninFigure4-2.

Figure 4-2: IP Information Screen

ConfigurationoftheIPAddress

3.Atthe“#”prompt,enterthefollowingcommandandpress<Enter> as shown in Figure 4-3.

IGS-5225-8P4S#configureterminalIGS-5225-8P4S(config)#interface vlan 1IGS5225-8P4S(config-if-vlan)#ip address 192.168.1.100255.255.255.0

The previous command would apply the following settings for theIndustrialManagedSwitch.

IPAddress:192.168.1.100SubnetMask:255.255.255.0

11

Figure 4-3: Configuring IP Address Screen

4.Repeatstep1tocheckiftheIPaddresshaschanged.

Storethecurrentswitchconfiguration

5. At the “#”prompt,enterthefollowingcommandandpress<Enter>.

#copyrunning-configstartup-config

Figure 4-4: Saving Current Configuration Command Screen

If the IP is successfully configured, the IndustrialManagedSwitchwillapplythenewIPaddresssetting immediately.YoucanaccesstheWebinterfaceoftheIndustrialManagedSwitchthroughthenewIPaddress.

Note

Ifyouarenot familiarwiththeconsolecommandortherelated parameter, enter “help” anytime in console to getthehelpdescription.

12

5. Starting Web ManagementThe following shows how to start up the Web Management of the Industrial Managed Switch. Note the Industrial Managed Switch isconfigured through an Ethernet connection. Please make sure themanager PC must be set to the same IP subnet address.

Forexample,thedefaultIPaddressoftheIndustrialManagedSwitchis192.168.0.100, then themanager PC should be set to192.168.0.x (where x is a number between 1 and 254, except 100), and thedefaultsubnetmaskis255.255.255.0.

IP Address:192.168.0.x IP Address:

192.168.0.100

IGS Industrial Switch

RJ45/UTP-Cable

Figure 5-1: IP Management Diagram

5.1 Logging in to the Industrial Managed Switch1.Use Internet Explorer 8.0 or above for Web browser and enter IPaddress http://192.168.0.100 (the factory-default IP address) toaccess the Web interface.

2.Whenthefollowingdialogboxappears,pleaseenterthedefaultusername “admin” and password “admin” (or the password you havechangedbefore)asshowninFigure5-2.

13

DefaultIPAddress:192.168.0.100DefaultUserName:adminDefaultPassword:admin

Figure 5-2: Login Screen

3.After entering the password, the main screen appears as shown inFigure 5-3.

Figure 5-3: Web Main Screen of Industrial Managed Switch

14

The Industrial Managed Switch Menu on the top and left of theWeb page lets you access all the functions and status the IndustrialManaged Switch provides. The Switch Menu always contains one ormorebuttons, suchas“System”,“Switching”,“QoS”,“Security” ,“PoE”, “Ring”,“ONVIF”and“Maintenance”.

Figure 5-4: Switch Menu

Now, you can use the Web management interface to continue theSwitch management. Please refer to the user manual for more.

Note

If you are not familiar with Switch functions or the related parameter, press “Help icon” like the following anytime on the Web page to get the help description.

15

5.2 SavingConfigurationviaWebTo save all applied changes and set the current configuration as astartup configuration, the startup-configuration file will be loadedautomatically across a system reboot.

1. Click the Save icon on the top Switch Menu bar.

Figure 5-5: Save Config -- Hot Key

2. Press the “SaveConfiguration” button.

3. Or the other way to save the setting is to Click Maintenance,Save StartupConfig.

Figure 5-6: Save Config -- Maintenance

16

6.RecoveringBacktoDefaultConfigurationTo reset the IP address to the default IP address “192.168.0.100” and the user password to factory default mode (default passwordis admin), press the hardware reset button on the front panel forabout 10 seconds. After the device is rebooted, you can log in themanagement Web interface within the same subnet of 192.168.0.xx and default password. Be noted that all the previous setups will bedisappearedafterthefactorydefaultresetismade.

P1 P2 FAULT

Ring

RESET

115200,N,8,1

1000LNK/ACT

R.O.

6

Reset

Figure 6-1: IGS-5225-4T2S Reset Button

17

Reset

ACTLNK9

LNK/ACT1000LNK/ACT1000

10

RESET

9

Console

115200,N,8,1

10

100/1000X SFP

ACTLNK

PoE In-Use

P1

Ring

P2 FAULT

R.O. I/O

240W

PoE Power Usage

180W

120W

60W

Figure 6-2: IGS-5225-4UP1T2S Reset Button

IGS-5225-8P2T2S

5

3

1

RESET

6

4

2

PoE-in-Use

LNK ACT

802.3at PoE+Reset

Figure 6-3: IGS-5225-8P4S/IGS-5225-8P2T2S Reset Button

18

Reset

P1 P2 Fault

Ring R.O.

Console115200,N,8,1

ACT1000 LNKACT100 LNK

5 6

120W

PoE Usage

90W

60W

30W

Reset

Figure 6-4: IGS-5225-4P2S Reset Button

19

7. Customer SupportThankyouforpurchasingPLANETproducts.YoucanbrowseouronlineFAQ resource on PLANETweb site first to check if it could solve yourissue. If you need more support information, please contact PLANETswitch support team.

PLANETonlineFAQs:http://www.planet.com.tw/en/support/faq.php

Switchsupportteammailaddress:support@planet.com.tw

IGS-5225-4T2S/IGS-5225-4P2S/IGS-5225-8P4S/IGS-5225-8P2T2S/IGS-5225-4UP1T2SUser’sManual:http://www.planet.com.tw/en/support/downloads?method=catego-ry&c1=industrial-ethernet&p=&type=3

(Please select your switchmodel name from the Product Model drop-downmenu)

Copyright © PLANET Technology Corp. 2018.Contents are subject to revision without prior notice.PLANET is a registered trademark of PLANET Technology Corp.All other trademarks belong to their respective owners.