Quality, Durability Reliability For Life Time - kawsar.com.af · WATER HAND PUMPS / Tel:+93799748377 ISO 9001:2008 | ISO 14001:2004 CERTIFIED COMPANY INTRODUCTION The dream of Pioneer,

Pakistan StandardsSP

Quality, Durability Reliability For Life Time

Manufactures According To

Edited with the trial version of Foxit Advanced PDF Editor

To remove this notice, visit:www.foxitsoftware.com/shopping

WATER HAND PUMPS www.kawsar.com.af / Tel:+93799748377

ISO 9001:2008 | ISO 14001:2004 CERTIFIED COMPANY

INTRODUCTION

QUALITY POLICY

Our MissionOur Vision

WHY KAWSAR?

Advantages of Kawsar Hand Pumps

AFFRIDEV / INDUS WATER HAND PUMP

Salient FeaturesConstrictionPump Head Assembly

CYLINDER ASSEMBLY

Connecting RodRiser Pipe

KABUL WATER HAND PUMPS

Salient Features

AFRIDEV DEEP WELL PAMIR WATER HAND PUMPSalient Features

KAWSAR SPECIFICATION AND MATERIAL TOLERANCES

Galvanizing Anti Corrosive TreatmentQuality Control

INSTALLATION STRUCTURE

KAWSAR CAST IRON / ABYAAR HAND PUMP

Salient FeaturesApplication Data

CAST IRON / ABYAAR HAND PUMP

SPECIAL THANKS TOSuggestions & Recommendations

PHOTO GALLERY

INDEX1

2

3

4

5

6

7

8

9

10

11

12

13

4

5

6

7

8

9

10

11

12

13

14

15

16





PSI Pakistan Standards Institution (Govt. of Pakistan)

LGRD Local Govt. of Rural Development Dept (NWFP)

SGS Societe General DE Surveillance

PHED Public Health Engineering Deptt. Govt. of NWFP.

WMD Water Management Deptt. Govt. of NWFP, Punjab

PSQCA Pakistan Standard & Quality Control Authority

ISO International Standards Organization

DACCAR Danish Committee for Aid to Afghan Refugee

SCA Swedish Committee for Afghanistan

IRC International Rescue Committee

UNICEF United Nations Children Emergency Fund for Pakistan and Afghanistan

UNDP United National Development Program

ICRC International Committee of the Red Cross

QC

QRC

SRSP

Qatar Charity

Qatar Red Crescent

Sarhad Rural Support Programme

MES Military Engineering Services PKPWD Pakistan Public Works Department

Certified Company

APPROVED BY

ENLISTED WITH





INTRODUCTION

The dream of Pioneer, KAWSAR PIPE Manufacturing Company is a major Presence in manufacturing of

community type of water Hand Pumps and its components. KAWSAR PIPE Manufacturing Company has established in 1994 as a manufacturer for water Hand Pumps in Pakistan as named Kawsar-Engg and now is going to start its Water Hand Pumps manufacturing in Afghanistan .

Kawsar Pipe Manufacturing Company has registered with Afghanistan Investment Support Agency (AISA) in Afghanistan since 2005 and with co-operation, collaboration and support of AISA Kawsar Pipe started its regular production of plastic Polyvinyl Chloride (PVC) Pressure and Non-Pressure Pipe system for cold, potable water and other industrial uses. After achievement in PVC Kawsar Pipe now started PPR-C, HDPE Pipes & Fitting with Advance Technology and a manufacturer for Water Hand Pumps.

Kawsar Pipe previously started its production in Peshawar Pakistan as named Kawar-Engineering Private limited which has established in 1994 as a manufacturer for water Hand Pumps, PVC Pressure, Non-Pressure Pipe, PPR-C, HDPE Pipes & Fitting. The executive partners and management of Kawsar-Engineering decided to commence PVC Pipes manufacturing company in Afghanistan after with their efforts and support of Afghanistan Investment Support Agency (AISA), Kawsar-Engineering was able to establish a manufacturing company named “KAWSAR PIPE”

Pakistan StandardsSP

I S O 9 0 0 0 : 2 0 0 8

CERTIFIED COMPANY

In our quest to lead by example, our joint efforts have led KAWSAR to ISO 9001:2000 Certification and accreditation for supreme product performance and quality by the Pakistan Standard Institute (PSI) and Pakistan Engineering Council.

100%100%100%Food Grade

Material Food Grade

Material Food Grade

Material

Manufactures According To International Standards

4

CERTIFICATIONS



http://www.foxitsoftware.com/shopping

WATER HAND PUMPSwww.kawsar.com.af / Tel:+93799748377


Kawsar total quality control perceptive is taken as a principal while performing the mission. Our main policy is to provide the present and future needs and demands of our customers in the most economical way and on time. In all our processes, we adopt in the principle of customer oriented understanding.

Aim for improvement full participation of our staff. In this process management, our main goal is to continuously improve our production and to respond the demands of our customers, personals and suppliers.

To increase the number of pleased and trusted customers in our sector by satisfying them from our quality.

To be committed to the mission of being the symbol of trust and contentment in the plastic and fittings market, KAWSAR proceeds to this targets as being the leader in the domestic market. And being a under rental and permanent supplier in the international market.

Being one of the best firms in the country in manufacturing sector of PVC, PPRC, HDPE Pipes and Fittings, Kawsar Gives at most of the importance to the Quality control and:

1. Uses the most appropriate material

2. Has the most advanced high technology

3. Has well qualified technical Staff and Experienced Labor

4. Produces Pipes in compliance with the International Standards.

5. Has Well equipped laboratory which is round the clock busy to control the

Quality at each stage of production

QUALITY POLICY

OUR MISSION

OUR VISION

WHY KAWSAR?






We are manufacturing a wide range of deep well and shallow well Hand pumps, which includes the most Afridev, Kabul, Pamir and Cast Iron/ Abyaar Hand pumps of very high quality. These pumps are manufactured as per the SKTA & HTN specifiedStandards.Kawsar Pipe is a recognized TOP Exporterfor Water Hand Pumps and also ISO certified9001:2008 and ISO 14001 certified Company, manufacturer & exporter of shallow & deep well hand pumps [FROM 9 TO 90 meters depth] having its manufacturing facilities in Government approved Industrial areas in AFghanisan

MANUFACTURING FACILITY / TECHNICAL STAFFWe have our own fabrication, welding, machine shop, draw bench, electro plating and galvanizing unit. Excellent tool room facilities.Best talents over 25 years of experiences from industry are working for organization yielding excellent results for end product to the satisfaction of our esteemed customers.

R&D / QUALITY/ DESIGN & DEVELOPMENTThe foundation of Kawsar growth over the years is the deep understanding of economic stimuli and customer needs, and the ability to translate them into customer-desired offerings through leading edge Research and Development. The Hand pumps & accessories are strictly made as per national & international standards like SKAT, HTN and DIN etc. We also accept and had done Multi National Inspection agencies like CROWN AGENTS, SGS, BUREU VERITAS, INTERTEC TESTING SERVICES, etc.

KAWSAR HANDS PUMPS TYPES

Afridev Hand Pump Kabul Hand Pump Pamir Hand PumpCast Iron/

AbyaarHand Pump






ADVANTAGES OF KAWSAR HAND PUMPS :KAWSAR Hand Pump are according to SKAT & HTN manual and specifications

KAWSAR Hand Pumps are Hot Dip Galvanized due to which it's most harmful to health

KAWSAR Hand Pumps are made of appropriate material

KAWSAR Hand Pumps utilizes the most advanced technalogy

KAWSAR Hand Pumps has a well equipped seprate laboratory for Hand Pumps,

which is round the clock busy to control quality at each stage of production

KAWSAR Hand Pumps all rubber & Plastic spare parts are produced by it self by latest

injection mold machines.

Features with Options:

PUMP HEAD:

CONNECTING RODS:

RISER PIPE:

CYLINDER:

PEDESTAL:

SPECIAL TOOL KITS:

STANDARD TOOL KITS:

Mild steel hot dip galvanized construction.

Hot dip galvanized Single or Double Hook, Stainless Steel Single or Double Hook Connecting Rods

PVC 63mm or HDPE 63mm

PVC brass sleeved Single and Double Hook, Also Stainless Steel Available.

Three Legged, Square Flanged &UNICEF Padestal.

For installation & maintenance of hand pumps

For installation & maintenance of hand pumps

Kawsar Specification and Material Tolerances?All Parts of Hand Pumps are according to Drawing and specification of SKAT.?The washer, bolts and nuts used for Afridev hand pump assembly confirm the specification given in Afridev

Hand Pump Specification’s (Edition 2003)?Pipes included raising main PVC pipe, steel pipes and tubes qualify the standard and Specification given in

Afridev Hand Pump Specification (Edition 2003).?The steel plates, sheets, Angle iron leg and square bars for Fabrication of the Afridev Hand Pumps confirm the

designation ISO 630/DIN 17100, ST 37-2 (as per Afridev . Hand Pump Specification Edition 2003.?The square tube confirm to ISO 4019/DIN 5911, Hollow section for structural Engineering.?All plastic and rubber parts are made according to Afridev Hand Pumps Specification’s (Edition 2003).?The Brass cylinder liner is made of seamless tubing of CuZn37 Confirming to DIN 17660.?In some parts of the pumps minor changes are proposed by WSG (Water supply and Sanitation Sectoral Group).






Galvanizing Anti Corrosive Treatment

The following assemblies are Galvanized according to "Afridev Hand Pump specification" (Revision - 2, 1994)

a. Pump Head Assembly

b. Cover Assembly

c. Handle Assembly

d. Stand Assembly

e. Pump Rod Assembly (unless stainless steel in used)

The following are Electro-Galvanized and passivated to DIN 50961 Fe/Zn12c, Electroplated Coating, Coating of Zinc and Cadmium coating on Iron and steel.

a. Fulcurm pin and rod hanger pin.

b. Spanner

c. All bolts, nuts and warshers (except stainless Steel/Chromate conversion coating type C to DIN 50941, protection against corrosion, chromating of electroplated Zinc and Cadmium coating.

A well-trained and highly skilled staff has been employed to check and maintain a strict quality control at each step of the manufacturing process. Various tests are taken to ensure that the Hand Pumps are always of high standard and confirm to the appropriate standard/specification. Finally a thorough checking is done by a well qualified inspection team like SGS international etc. We provide best possible material and services to our valuable customers.

Quality Control




Afridev Indus Hand Pump

The Afridev hand pump is a public-domain pump which can pump water from up to 45-60 meters below ground surface. This pump is designed with a "working barrel" which allows the piston to be extracted without removing the rising main. A special "hook" tool is required to extract the foot valve from the bottom of the cylinder. It is suitable for boreholes with casing sizes of nominal 100mm, 127mm or 200 mm internal diameter and Hand Dug Well.



Pump Type:Afridev deep well hand pump as per SKAT-HTN Switzerland specifications, with 50mm dia open top, UPVC brass lined cylinder assembly with extractable plunger and foot valves assemblies.

Recommended for water level setting depth: up to 45 Meter.

Minimum ID of bore (mili meter) : 100

Approximate DischargePer Stroke: 440ml

Approximate Discharge per 60 Strokes/min: 24 liters

Approximate Discharge (Litres/Hour): 90 liters

PVC Riser Pipe = 63mm OD * 4.7mm Wall Thickness

MS/SS Connecting Rod Diameter = 10mm

Stroke Length= 225± 6mm

Note: Data given are recommendatory: There may be some variation under actual field conditions design and specifications subject to change without prior notice.

Ideal VLOM (Village Level Operation and Maintenance). Designed and developed keeping in view .maintenance Problem.Capable of lifting water from depths up to – approx 45 meters.Fully fabricated steel structure duly Hot Dip Galvanized.Adjustable Handle to suite varying installation depths.Injection Molded special grade plastic bush bearings easy to replace at village level.Interchangeable plunger & foot valves easy extract without removing riser pipe.Non-corrosive underground components capable of handling corrosive water situation there by giving longer life.Easy installation and inexpensive maintenance at village level. Women can handle easily.

SALIENT FEATURES




Connects cylinder to pump head and is a passage for water. uPVC pipe 63 mm OD x 4.7 mm wall thickness x 2.9 meters long with socket-spigot cemented joint. Each pipe is provided with a rubber pipe centralizer to avoid contact with casing pipe



CONSTRUCTION

Fully fabricated steel structure duly Hot Dip Galvanized.Adjustable handle providing different handle settings to suit different cylinder setting depths.Conical flange with conical rubber grommet provides better holding grip on UPVC Riser Pipe.Fulcrum & rod hanger pins are supported on special grade plastic bush bearing which are very easy to replace at a village Level.Fully covered to avoid any contamination of water. Design offers a stroke length of 225mm.

The complete system of KAWSAR AFRIDEV Hand pump consists of four main sub assemblies briefly described below.

PUMP HEAD ASSEMBLY

CYLINDER ASSEMBLYUPVC pipe 63mm (OD) x 4.7 mm thick lined from inside with seamless brass liner 50 mm I.D. x 700 long.

Interchangeable plunger and foot valves made out ofInterchangeable injection molded delrin with stainless steel.Pick up device mounted on foot valves for easy extraction of Foot valve without removing riser pipe.

U-seal, bobbins steel and O rings are of nitride rubber and plunger rod of stainless steel and can be mild steel.Larger dia extension pipe at the bottom of cylinder reduces silt and sand intake.Sleeve is provided for plastic rope to pass for supporting the System during installation and maintenance.

RISER PIPE

Kawsar uPVC R

ising main 63mm






KABUL Hand PumpThis is mini Afridev water Hand Pump named Kabul because mostly this hand pump is installed in “Afghanistan”. Since economical condition of Afghanistan is very weak so, most of UN agencies and NGO, S involved in drinking water sector in Afghanistan decoded to design such Hand Pumps, which might be low in price and its parts may be easily interchangeable with Afridev (Indus) Hand Pump.

Thus, DACAAR (Danish Committee for Aid to Afghan Refugees), the Leading agency in drinking water sector took initiative to design it and arrange Drawing; it s field-testing and other information shard with UNICEF Afghanistan.

Pump Type:Kabul Hand Pump pump as per SKAT-HTN Switzerland specifications, with 50mm dia open top, UPVC brass lined cylinder assembly with extractable plunger and foot valves assemblies.







MS/SS Connecting Rod Diameter = 10mm


Note: Data given are re-commendatory: There may be some variation under actual field conditions design and specifications subject to change without prior notice.

Kabul water Hand Pump is suitable for lifting water from depth up to 20 m.

It is suitable for boreholes (with same casing size as in Afridev) and Hand dug well.

Parts of Kabul and afridev water Hand Pumps are the same and easily interchangeable.

Kabul Water Hand Pump body is slightly lighter than afridev Water Hand Pump.

Kabul Hand Pump handle is not adjustable and lighter than afridev pump.

SALIENT FEATURES

CONSTRUCTION

The complete system of KAWSAR Kabul Hand pump consists of four main sub assemblies briefly described below.






Connects cylinder to pump head and is a passage for water. uPVC pipe 63 mm OD x 4.7 mm wall thickness x 2.9 meters long with socket-spigot cemented joint.

Each pipe is provided with a rubber pipe centralizer to avoid contact with casing pipe.

PUMP HEAD ASSEMBLYFully fabricated steel structure duly Hot Dip Galvanized.Adjustable handle providing different handle settings to suit different cylinder setting depths.Conical flange with conical rubber grommet provides better holding grip on UPVC Riser Pipe.Fulcrum & rod hanger pins are supported on special grade plastic bush bearing which are very easy to replace at a village Level.Fully covered to avoid any contamination of water. Design offers a stroke length of 225mm.

CYLINDER ASSEMBLY

UPVC pipe 63mm (OD) x 4.7 mm thick lined from inside with seamless brass liner 50 mm I.D. x 700 long.Interchangeable plunger and foot valves made out ofInterchangeable injection molded delrin with stainless steel.Pick up device mounted on foot valves for easy extraction of Foot valve without removing riser pipe.U-seal, bobbins steel and O rings are of nitride rubber and plunger rod of stainless steel and can be mild steel.Larger dia extension pipe at the bottom of cylinder reduces silt and sand intake.Sleeve is provided for plastic rope to pass for supporting the System during installation and maintenance.

RISER PIPE






Afridev Pamir Hand Pump

For those areas where water table was lower than 50 m, Afridev Hand Pumps were not working properly. The UN agencies and other NGO’S who were involved in Drinking Water sector working in Pakistan as well as inside Afghanistan started Research to find such Hand Pumps that can easily lift water from the desired depth. Finally SKAT (Swiss Center for Development Cooperation in Technology and Management), the designer of Afridev, took initiative to design Afridev Deep well (Pamir) Hand Pumps.

PUMP TYPE: Afridev PAMIR deep well hand pump as per SKAT-HTN Switzerland specifications, with 50mm dia open top, UPVC brass lined cylinder assembly with extractable plunger and foot valves assemblies.







MS/SS Connecting Rod Diameter = 10mm, Double Hook


Note: Data Given are recommendatory: There may be some variation under actual field conditions design and

pecifications subject to change without prior notice.

Pamir water hand pumps are suitable for lifting water from depth up to 80 m.It is suitable for bore holes (with same casing size as in Afridev Water Hand Pump) and hand dug well.Pump body, stand (Pedestal), Top Cover, Rubber Components, Plastic Components (Foot valve and Plunger) and Cylinder except Plunger Rods are the same as Afridev Water Hand Pumps.Handle is stronger and Heavy; Ball bearing with different pins and hosting is used this pump instead of Plastic bearing.Pump Rod used in this pump is “Double Hook & Eye”, and is completely different from Afridev Hand Pumps rod.

SALIENT FEATURES





Connects cylinder to pump head and is a passage for water. uPVC pipe 63 mm OD x 4.7 mm wall thickness x 2.9 meters long with socket-spigot cemented joint.

Each pipe is provided with a rubber pipe centralizer to avoid contact with casing pipe.

CONSTRUCTIONThe complete system of KAWSAR AFRIDEV PAMIR Hand pump consists of four main sub-assemblies briefly described below.

PUMP HEAD ASSEMBLY

Fully fabricated steel structure duly Hot Dip Galvanized.Adjustable handle providing different handle settings to suit different cylinder setting depths.Conical flange with conical rubber grommet provides better holding grip on UPVC Riser Pipe.Fulcrum & rod hanger pins are supported on special grade plastic bush bearing which are very easy to replace at a village Level.Fully covered to avoid any contamination of water. Design offers a stroke length of 225mm.

CYLINDER ASSEMBLYUPVC pipe 63mm (OD) x 4.7 mm thick lined from inside with seamless brass liner 50 mm I.D. x 700 long.Interchangeable plunger and foot valves made out ofInterchangeable injection molded delrin with stainless steel.Pick up device mounted on foot valves for easy extraction of Foot valve without removing riser pipe.U-seal, bobbins steel and O rings are of nitride rubber and plunger rod of stainless steel and can be mild steel.Larger dia extension pipe at the bottom of cylinder reduces silt and sand intake.Sleeve is provided for plastic rope to pass for supporting the System during installation and maintenance.

RISER PIPE



Abyar Hand Pump

KAWSAR Abyaar Na. 6 is a cast iron suction pump, capable of drawing water from shallow depths by creating a partial vacuum in the suction pipe depending as they do on at atmospheric pressure to drive water up to the surface. The pump use is restricted to regions with water table no more than 40-50 teets below the surface. For reasons of economy and convenience this pump has become very popular for serving individual families and small group at communities. Millions of pumps are in regular use in the Asian countries. With minimum sltill this pump can be installed and maintenance can be carried out. lt lifts water twice faster than Atridev Hand Pump.








PVC Riser Pipe = 1 ½” D Class PVC Pipe

Note: Data given are recommendatory: There may be some variation under actual field conditions design and specifications

subject to change without prior notice.

It is Suitable for depths upto 40-50 leets. It is constructed almost entirely of Cast Iron.

It is mounted directly on to l '/2" galvanized iron pipe.

The Plunger is a molded PVC cop washer which ensures less wear.

The checlc valve is a simple leather flap with C .| weight.

All moving parts are above ground level and are easily accessible.

The pump requires very simple maintenance, using skill and few tools meeting Village

Level Operation & Maintenance (VLOM) concept.

SALIENT FEATURES

APPLICATION DATA:

Operating depth 40-50 feets depth

Operated Strokes per minute

Average discharge per stroke

Pump Weight

45 (Approx.)

20-30

1.2 – 1.3 Litres

31- Kg






CAST IRON / ABYAR HAND PUMP DIAGRAM7

5

23 2

7

SECTION BB

7

SECTION AA

7

5

3 8

3

AA

B B

410

12

112

1

8

3

1012

11

13

9

INSTALLATION MARK

1 ½” Pipe

No. off Description

13

12

11

10

9

8

7

6

5

4

3

2

1

Part No.

1

9

8

9

1

1

4

1

1

1

1

1

1

Rubber Gasket

Spring Washer for w12 bolt

Max. Bolt w12 x1.75 - 65 long

Max. Bolt w12 x1.75

Bolt Assembly

Plunger Assembly

Leather Check valve with C.I weight

Fulcrum Pin

Plunger Pin

Sliding Plate

Handle

Hood

Body






ISO 9001- 2000 CERTIFIED COMPANY

Rubber Cone Flapper

Pipe Centerlizer Rod Centerlizer

Plunger Bearing

Small Pin Large Pin

Babin

Small Ring Large Ring U-Seal

Pumphead

Mounting Flange

Concrete Pedestal

RisingMain

Bore Hole

Pump Rod

RodCentarliser

Plunger

Foot Valve

Foot ValveReceiver

T-BarHandle

INSTALLATION STRUCTURE






SUGGESTIONS & RECOMMENDATIONS

SPECIAL THANKS TOPOLYMERS STRUCTURE & PROPERTIES (By C.A. Daniels, Ph.D. Senior Materials Engineers, USA)

PLASTIC MATERIAL & PROCESSING(By A.Brent Strong, USA)

PVC COMPOUNDING & PROCESSING(By L.K. Mutreja)

HAND BOOK OF PLASTIC TEST METHODS (By R.P. Brown, England)

MODERN PLASTIC ENCYCLOPEDIA HAND BOOK(By Patrick Toensmeier)

ASIAN PLASTICS NEWS MAGAZINE(By C.A. Daniels, Ph.D. Senior Materials Engineers, USA)

We have tried to make this catalogue error free, however suggestions and recommendations to improve the contents and materials will be highly appreciated.

Catalogue Designed, Researched & Developed ByKAWSAR TECHNICAL & SENIOR STAFF






PHOTO GALLERY






PVC PIPESPPR-C PIPES

PVC CONDUIT PIPES

PVC SCREEN / SLOTTED PIPESPVC, CPVC SOLVENT CEMENT

PVC FITTINGS

PPR-C FITTINGS

HDPE WATER PIPES

MDPE GAS PIPES

HDPE CONDUIT PIPE

OTHER PRODUCTS




NOTE: Dear Customer, Please do not buy any of our products without our Kawsar Logo. Please try to buy / contact our registered offices/ Distributors mention on our website and Last Title back page of our catalogues for their addresses and contact Details becausesome people Miss use our brand name illegally. We just want to deliver you the best Quality Products with full technical support and cooperation.

is ne

op

ti

K

p

a

ci

w

ts

s

a

a

l

r

p

p

y

i

r

p

e

e

v

,

E

KAWSAR PIPE

DEALERS

KABUL: Shirkate-KAWSAR Pipe & AL-KAWSAR2. Between Charahi Haji Yaqoob & Charahi AnsariHaroon Market 2nd Floor.Cell: [email protected], [email protected], [email protected] www.kawsar.com.af

MAZAR:Haji Moqim Apartment, East of Roza-e-SharifPhone: 05024044901Cell: 0799212277, 0799043639, 0700501143 [email protected], [email protected]

NANGARHAR JALALABAD Pashtoonistan Watt Street, Gul Bahar Market, 2nd Floor, Jalal Abad City Afghanistan. Cell Phone: +93775343559, 0785930905, 0784475880

[email protected], [email protected] www.kawsar.com.af

KUNDUZ CITY:Rasta-e-Ahangiri, ShinwariMarket ,infront of Maiwand BankCell:-0705951434-0773133234, [email protected]

Dehmazang:Kawsar Pipe Agency Near to Cinema BarikotCell: 0799616452 [email protected]

KHOAST OFFICE:Markazi choak-e-Ijaz Market,Khoast Bazar Cell: 0799148889

KUNDOZ :Rasta-e-ahangary Shinwari Market in front of

Maiwand Bank

Cell: 0705951434, 0773133234

NINGERHAR JALALABAD:Pashtoonistan Watt Street, Gul Bahar Market,

2nd Floor,

Jalal Abad City Afghanistan.

Cell Phone: +93775343559, 0785930905, [email protected],

[email protected]

www.kawsar.com.af

HELMAND OFFICE:Lashkare Gah City Jade-e-Khyber Opp.at Haji Ubaidy Market.Cell: 0700487141 / 0798160812

For more details about our products, Catalogs or Technical Data Sheet please visit our website

www.kawsar.com.af --- [email protected]

www.kawsar.com.af, [email protected]

Head Office: 2nd floor, Haroon Market, Between Haji Yaqub and Ansari Square, Shahrnaw, Kabul Afghanistan.Cell: (+93-202200901)-0799748377- 0799282028-0799377773Email: [email protected], [email protected], [email protected] Website: www.kawsar.com.afFactory: Kabul Jalalabad road Paktia kot area end of industrial states Tel: (+93-202320647) or (+93-0799748377) [email protected]





Documents

Quality, Durability Reliability For Life Time - kawsar.com.af · WATER HAND PUMPS / Tel:+93799748377 ISO 9001:2008 | ISO 14001:2004 CERTIFIED COMPANY INTRODUCTION The dream of Pioneer,