Upload
papina
View
33
Download
0
Tags:
Embed Size (px)
DESCRIPTION
Purpose. Determine the charge to mass ratio (e/m) of an electron. Design your own experimental procedures. Decide what measurements to take, the range of values you will measure, how to obtain the uncertainties of measured and computed quantities, how to analyze the data graphically, and - PowerPoint PPT Presentation
Citation preview
Physics 2225: e/m Experiment
Purpose
Determine the charge to mass ratio (e/m) of an electron.
Design your own experimental procedures. Decide• what measurements to take,• the range of values you will measure,• how to obtain the uncertainties of measured and computed quantities,• how to analyze the data graphically, and• what error propagation procedures to perform.
Gain experience in writing a report in the form of a scientific paper.
Physics 2225: e/m Experiment
Background1892: Hendrik Lorentz introduces the force acting on a charged particle moving through a magnetic field (the Lorentz force, or magnetic force):
)( BvqFm
The cross product means:1) Only the components of the vectors v and B that are perpendicular
to each other contribute to the force.2) The force is perpendicular to both the vector v and the vector B.
Physics 2225: e/m Experiment
q
mF
v
B
The charge here is assumed to be positive.For negative charges the force would be downwards.
(points into the page)
Physics 2225: e/m Experiment
B
qmF
v
The force continually changes the direction of the velocity, but not it’s magnitude.
The direction of the force changes also and it’s magnitude also remains the same.
(points into the page)
circular path
mF
q
vr
Physics 2225: e/m Experiment
For Circular Motion (Radius r)
rvmmaF lcentripetam
2
Derive expression for e/m(v,B,r)=…..
Physics 2225: e/m Experiment
Getting the electron up to speed …and knowing what that speed is.
Ifilament
filament electrons
Many electrons return because they hit the plate.(Note: return path of electronsis opposite to conventional current.)
acceleratingvoltage(150V-300V)
filamentVoltage(6V)
Some electrons miss the plate and flythrough the hole in the plate. electron beam comes out of hole.
The filament current heats up the filament electrons get enough energy to exit the filament.Electrons get accelerated by the force in the electric field (created by the accelerating voltage).
Speed increases as electrons approach plate
v v vE
Physics 2225: e/m Experiment
Getting the electron up to speed …and knowing what that speed is.
v v v
electron has potential energy = eVacc
and kinetic energy = 0
electron has potential energy = 0and kinetic energy = ½ mv2
Conservation of energy: acceVmv 221
accV
Physics 2225: e/m Experiment
Generating the Magnetic Field
A pair of Helmholtz coils
a
INB o
23
45
N turns of wire in each coil.
IIB
Magnetic field in thecenter of the Helmholtzcoil pair.
a
I
I
Physics 2225: e/m Experiment
Power Supplies
Before you switch on the power supply:
• Identify all components according and verify that all connections are as shown in the lab manual.
• Identify on the high voltage power supply the dial that controls the accelerating voltage: Turn that dial all the way counterclockwise into the zero position.
• Identify on the low voltage power supply the two dials that control the current through the Helmholtz coil: Turn both dials (voltage control and current control) counterclockwise into the zero position.
• Identify on the low voltage power supply the heater voltage dial. This is a step dial. Verify that it is set to 6 Volts.
Physics 2225: e/m Experiment
High Voltage Supplies
Older model
Newer model
Physics 2225: e/m Experiment
Low Voltage Power SuppliesOlder model
Newer model
Heater voltage:must be dialedto 6V
Helmholtz coilcurrent andvoltage regulation
Physics 2225: e/m Experiment
Switching on the Power Supplies
Now switch on both power supplies. Check and make sure that the Helmholtz coil current is zero and the accelerating voltage is also zero.
Look at the tube: You should see the filament glow orange/yellow.
Carefully dial up the accelerating voltage on the high voltage power supply to about 200V (never exceed 300V).
Regulating the current in the Helmholtz coil:
There are 3 knobs that control voltage and current through the Helmholtz coil:
1) Current adjustment knob for Helmholtz coils on the e/m apparatus.2) Current adjustment knob on low voltage power supply.3) Voltage adjustment knob on low voltage power supply.
Next page: how to use these three knobs.
Physics 2225: e/m Experiment
Regulating the Current in the Helmholtz Coil:
First turn DC VOLTAGEADJUST to zero (all theway counterclockwise)
Then turn DC CURRENTADJUST all the way clockwise (max. current).
Then turn current adjust knobOn the e/m apparatusall the way clockwise (max. current).
The current meter should STILL READ ZERO.
Physics 2225: e/m Experiment
Regulating the Current in the Helmholtz Coil:
Carefully turn DC VOLTAGEADJUST clockwise. Watch the current meter!When current meter reaches2 Amps: Stop!!Leave at this setting!!
From now on only regulatethe current with this knob onthe e/m apparatus
Totally clockwise = 2A Totally counterclockwise = 0A
Physics 2225: e/m Experiment
Switching Off Power Supplies
Before you switch off the power supply:
• Identify on the high voltage power supply the dial that controls the accelerating voltage: Turn that dial all the way counterclockwise into
the zero position.
• Identify on the low voltage power supply the two dials that control the current through the Helmholtz coil: Turn both dials (voltage control and current control) counterclockwise into the zero position.
Now switch off.
Physics 2225: e/m Experiment
HintsWhen measuring the radius of the electron’s circular path, take advantage of the mirror-scale behind the tube:- Move your head to the left or right until the mirror image of the beam overlaps the actual electron beam. Then read off the scale.- Repeat the procedure for the left side.
- Determine diameter from the two values (radius is half of that).
Read off right side Read off left side
Physics 2225: e/m Experiment
Important for the Longevity of Apparatus
• Never exceed 300V on the accelerating voltage. Always monitor this voltage on the attached volt meter when changing that voltage.
• Never exceed 2A on the Helmholtz coil current. Always monitor this current with the attached current meter when changing that current.
• Always dial down accelerating voltage and Helmholtz current to zero before switching off the power supplies.
Physics 2225: e/m Experiment
Lab Report
Lab report must be written in the form of a scientific paper(see example in the back of the lab manual).
Each person must write their own lab report(no group report for this experiment).
You have 1 week to complete and submit the lab report.
Late lab reports will get a deduction of 5% per day late(e.g., if your report is 3 days late you will only get credit for 85% of the score that you would have gotten if you submitted on time).