PUMPiNG systeMs PUmPinG SYStEmS (continUEd) · PDF fileCONYERS, GA (800) 241-5652 APOPKA, FL (800) 432-1869 GOLDSBORO, NC (800) 426-9293 - 69 - PUmPinG SYStEmS (continUEd) Vertical

CONYERS, GA (800) 241-5652APOPKA, FL (800) 432-1869GOLDSBORO, NC (800) 426-9293 - 69 -

PUmPinG SYStEmS (continUEd)

PuMPING SYSTEMSVertical Tanks, Pump Kits, Bulkheads

LF1-AECONOMY PuMP KITThis kit includes a manually operated liquid withdrawal valve with a 1” outlet. All fittings to the pump are 1”.

LF1-BDELuxE PuMP KITDeluxe kit includes Fisher’s 1 1/4” internal valve. All piping components are 1 1/4”.

See appendix for material lists & schematics of these kits.

BUlkHeads

BuLK PLANT BuLKHEADS

PUMPiNG systeMs

The following kits are primarily designed to be used with a small capacity pump like Blackmer’s LGF1C (10 GPM) or LGF1PC (15 GPM)

For a pumping system to perform properly, you must have high quality equipment installed in accordance with the manufacturer’s recommendations and the following good installation practices:

1. The tank should be installed with as much vertical distance from the bottom tank outlet to the pump inlet as practical. The minimum recommended distance from the bottom of the tank to the ground is 16” for good pump performance.

2. Only bottom tank outlets should be used to supply gas to liquid pumps, and the size of these outlets should be no less than the inlet of the pump. There should be no restrictive fittings on the inlet side of the pump.

3. The pump should be located as close to the tank outlet as practical. A LP gas pump can push gas for reasonable distances, but cannot suck gas. Liquid gas must be fed to the pump by gravity.

4. All positive displacement pumps require a bypass line to return gas back to the tank. The Blackmer LGF1E and LGF1PE pumps have built in bypass valves. A line must be run between the pump and the tank to protect the pump against excessive differential pressure.

5. Proper electrical wiring connections and correct wire size are important for good pump performance. Be sure the motor terminals are connected correctly for the voltage and rotation being used. Listed below are general recommendations for the minimal wire size for more common wiring runs on 1 HP and 1 1/2 HP single phase motors. Please comply with the motor manufacturer’s requirements concerning this matter.

ITEM# COuPLINGS STH16x10 2” and 1 1/4” STH16x16 Two 2” STH16x16x10 Two 2”, One 1 1/4” STH24x16 3” and 2” STH24x16x10 3”, 2”, and 1 1/4” STH24x16x16 3” and Two 2”

G

Length of Run Voltage wire SizeMotor Size: 1 HP Single Phase100’ 115 #8100’ 230 #10200’ 115 #6200’ 230 #8Motor Size: 1 1/2 HP Single Phase100’ 115 #4100’ 230 #10200’ 115 #0200’ 230 #8

- 70 -CONYERS, GA (800) 241-5652

APOPKA, FL (800) 432-1869GOLDSBORO, NC (800) 426-9293

FLANGE MOuNTING - DIRECT MOTOR DRIVEThese small positive displacement pumps are ideal for filling cylinders and motor fuel tanks. They mount directly to a C-face motor & have built in “back to the tank” bypass valves.

PuMP ONLY Item # Size CapacityLGF1E 1” 10 GPMLGF1PE 1” 15 GPMLGRLF1-1 1/4 1 1/4” 18 GPM

PumpsBLACKMER PuMPS

LGF DRIVE STYLE

DM DRIVE STYLE* Comes with one 2” flanged elbow. For two elbows, order TLGLF3C-2.

Item # Size CapacityLGL1-1/4DM 1 1/4” 20 GPMLGL1-1/2DM 1 1/2” 30 GPM

FLANGE MOuNTED PuMPSFOR BOBTAILS & TRANSPORTS Capacity is at 870 RPM and 50 psi differ-ential pressure.

Item # Inlet Aux. Inlet Outlet CapacityTLGLF3C* 3” flange 2” FNPT 2” FNPT 100 GPMTLGLF4B 4” flange 3” FNPT Dual 2” FNPT 379 GPM

VB DRIVE STYLEBASE MOuNTED - V-BELT DRIVEPuMP ONLYCapacity is at 640 RPM and 50 psi dif-ferential pressure.

Item # Size CapacityLGLD2E 2” 67 GPMLGLD3E 3” 133 GPMLGLD4 4” inlet 3” outlet 270 GPM

PuMP ASSEMBLYPump, hubs, sheaves, high-torque triple V-belts and belt guard mounted on a common base, ready to accept a standard NEMA motor. Capacity at 640 RPM and 50 psi differential pressure.

Item # Size CapacityLGLD2E-VB 2” 67 GPMLGLD3E-VB 3” 133 GPMLGLD4-VB 4” inlet 3” outlet 270 GPM

PuMP ASSEMBLYPump, coupling and coupling guard, mounted on a common base, ready to accept a standard NEMA motor.

BRACKET MOuNTING - DIRECT MOTOR DRIVEThese durable motor speed pumps offer capacities up to 35 GPM and are ideal for motor fueling, multiple station cylinder filling and a variety or small transfer jobs. They are designed for foot mounting to a common base plate.

PuMP ONLY Item # Size CapacityLGL1-1/4 1 1/4” 20 GPMLGL1-1/2 1 1/2” 30 GPM

LDF1 SERIES DISPENSER PuMPSSimilar to the LGF1 Series, but these are assembled with left-hand rotation which will allow them to retrofit in place of Corken C Series pumps. These pumps require an external bypass valve.

LGF1 SERIESw/ 115/230V Motor

* To include a switch with the assembly, add an “A” suffix to the item #. (LGFIE-101A)

Item # * Size HP CapacityLGF1E-101 1” 1 10 GPMLGF1PE-151 1” 1 1/2 15 GPMLGRLF-151 1 1/4” 1 1/2 18 GPM

H

blAcKmER PUmPS (continUEd)

Item# Size Capacity LDF1A 1” 10 GPM LDF1PA 1” 15 GPM

BlackMer PUMPs

Hydraulic Drive SystemBlackmer’s HYDRIVE is a filly integrated hydraulic drive system. A typical system includes a P.T.O., hydraulic pump, Hydrive cooler/controller, pump control valve, speed control valve, and mounting hardware. Hydraulic motor adapter kits are available to retrofit existing Blackmer pumps for hydraulic drive operation. Each system is factory engineered to fit your application.


BLACKMER PuMP PARTS By-Pass Valves, Repair Kits & Individual Parts

blACkMEr rEbuild kiTsRebuild kits include maintenance kits, rotor & shaft and liners.”* These kits include new and improved QA seal assemblies and double end rotor and shaft.

Kit Number Pump Replaces

899076 LGRLG-1 1/4 - 4 Vane 889017

899077 LGL-1 1/4 - 4 Vane 889018

899078 LGL-1 1/2 - 4 Vane 899019

899076 LGRLF-1 1/4 - 8 Vane

899077 LGL-1 1/4 - 8 Vane

899078 LGL-1 1/2 - 8 Vane

899079 LGLD2E*

899081 LGLD3E*

899080 TLGLF3C*

899022 TLGLF4A & LGLD-4

899124 TLGLF4B

H

BLACKMER BY-PASS VALVESDifferential bypass valves are designed to protect pumps and system components from excessive pressure damage. weld flanges are available by special order.

FISHER BY-PASS VALVES.

Pump Pressure Adjust. Item # Size Size Setting RangeN100A-10-2 1 1/4” 2”-3” 115 psi 50-150 psiN100A-12-2 1 1/2” 2”-3” 115 psi 50-150 psiN100-16-2 2” 4” 115 psi 50-150 psi

Pump Pressure Adjust. Item # Size Size Setting Range Cap. BV-3/4 3/4” 1 1/4”-1 1/2” 95 psi 70-100 psi 50 GPMBV-1 1” 1 1/4”-1 1/2” 95 psi 70-100 psi 50 GPMBV-1 1/4 1 1/4” 1 1/2”-2” 95 psi 70-125 psi 125 GPMBV-1 1/2 1 1/2” 2”-3” 95 psi 70-125 psi 125 GPMBV-2-30 2” 3”-4” 30 psi 20-40 psi 225 GPMBV-2-55 2” 3”-4” 55 psi 41-70 psi 225 GPMBV-2-95 2” 3”-4” 95 psi 90-125 psi 225 GPM

By-Pass valves

blACkMEr MAinTEnAnCE kiTsMaintenance kits do not include pump relief valve parts.

* These kits include new and improved QA seal assemblies

Kit Number Pump Replaces Add Pushrods

898994 LGF1E & PE - 4 Vane 892950

898994 LGF1E & PE - 6 Vane

898917 LGRLG-1 1/4 - 4 Vane 892302

898918 LGL-1 1/4 - 4 Vane *898976 (2) 123076

898919 LGL-1 1/2 - 4 Vane *898976 (2) 123401

898976 LGRLF-LGL 1 1/4 & LGL1’s - 8 Vane (2) 123009

898979 LGLD2E* 894420

898981 LGLD3E* 894427

898922 LGLD4*

898980 TLGLF3C* 895123

898922 TLGLF4A* 892031

899224 TLGLF4B

*Denotes necessary components not included in maintenance kit.

Note: All 2" to 4" pumps now have the new "A" seal.

- 72 -CONYERS, GA (800) 241-5652


BLACKMER PARTS LISTPUMP MODELS: LGF1E, LGB1E, LGF1PE, LGB1PE

and Discontinued ModelsLGF1D, LGB1D, LGF1PD, LGB1PD, LGF1C, LGB1C, LGF1PC, LGB1PC

(See Instructions 501-A00 for Installation, Operation and Maintenance)

Ref.No. Description

Partsper

PumpPart No. Ref.

No. DescriptionPartsper

PumpPart No.

2 Adjusting Screw – Relief Valve (R/V) 1 432901 28 † Capscrews – Bearing Cover 4 9200803 Locknut – Adjusting Screw 1 922811 28A † Bracket Mounting Screws 4 9200904 Cover – R/V 1 412901 28B † Bracket Mounting Screws 4 920101

4A O-Ring – Spring Guide 1 1 711940 28C Guard Screw 1 9200267 Spring Guide – R/V 1 422901 Coupling Half – Pump 9061508 Spring – R/V 1 472901 Coupling Half – Motor (56C) 906151

9 Valve – R/V 1 452901 Coupling Half – Motor(143-145TC/184C) 906147

9A Disc – R/V 1 442901

34

Coupling Spider

1

90615510 O-Ring – R/V Cover 1 1 701965 35 Key – Shaft 1 1 909126

Cylinder – LGF1, LGB1 022914 72 O-Ring – Head 1 1 71194112 †

Cylinder – LGF1P, LGB1P 1 022915 73 Gage Plug (1/4”) 2 90819873A † Plug (3/4”), External Bypass 1 90822513 Rotor & Shaft Assembly, Six Vane 2

(Includes Ref. Nos. 24A & 24B) 1 262907 76 Grease Fitting 2 31781514 Vane – Duravane (Std.)3 4, 6 1 092913 76A Grease Relief Fitting 2 701992

20 † Head 1 032905 104 Grease Seal 1 1 33193421 Capscrews – Head 4 920178 Bracket - (base mount) - LGB1(P)D 83291324 Ball Bearing 2 1 903405 108 Bracket (C-faced footless) - LGF1(P)D 1 832912

24A Locknut – Bearing 2 903531 108A Capscrews – Bracket 4 92033124B Lockwasher – Bearing 2 1 903532 108B Bracket (C-faced footed) SEE PAGE 226 † Gasket – Bearing Cover 1 1 383075 186 Guard 1 80412027 † Bearing Cover 1 043071 Tool - Locknut 903090

Kit – Maintenance (4-Vane) 898916Kit – Maintenance (6-Vane) 898994

1 Included in Maintenance Kit. 2 Discontinued 'D' and 'C' models shipped with a 4-vane rotor. The current 6-vane rotor is fully interchangeable aslong as the slotted vanes (pn 092913) are used. 3 The current slotted vanes (pn 092913) may be used in either the 6-vane or 4-vane rotors.The discontinued solid vanes may be used in the 4-vane rotors ONLY. Always install the vanes with the slot facing the direction of rotation.† To fit the LGB1(P)C, LGF1(P)C use: Ref. No. 12-022902/022911 respectively, Ref. No. 20-032902, Ref. No. 26-382901, Ref. No. 27-042901,

Ref. No. 28-920203, Ref. No. 28A & B-920230, Ref. No. 73A-908198, and Ref. No.108-832901/832905 respectively.Keep this parts list with Installation, Operation and Maintenance Instructions.

LOCKNUT TOOL

BLACKMER PuMP PARTS

H


MECHANICAL SEAL

Ref.No. Part Name

PartsPer

PumpPart No.

153 Mechanical Seal Assembly 2 1 332920153A** Jacket Assembly – Seal 2 332922153B** Stationary Seat (Steel) 2 332901153D O-Ring – Stationary Seat (Buna-N) 2 711916153F** Seal Face (Carbon) 2 332902153G O-ring – Rotating (Buna-N) 2 711939

1 Included in Maintenance Kit ** Ref. Nos. 153A, 153B & 153F are not available as separate repair parts.

MOUNTING BRACKET

Ref.No. Part Name

PartsPer

PumpPart No.

108B Bracket (C-faced footed) – LGF1(P)D 1 833000

BLACKMER PuMP PARTS PUmP modElS: lGF1E, lGb1E, lGF1PE, lGb1PE (continUEd)

H

- 74 -CONYERS, GA (800) 241-5652


BLACKMER PuMP PARTS

H

BLACKMER PARTS LIST

PUMP MODELS: LGRL1.25, LGRLF1.25A, LGL1.25, LGLF1.25A, LGL1.5, LGLF1.5A

and discontinued models: LGRLF1.25, LGLF1.25See Instructions 501-B00 for Installation, Operation and Maintenance

Ref. No.

Description Partsper

PumpPart No.

Ref. No.

Description Partsper

PumpPart No.

1 Cap – Relief Valve (R/V) 1 413200 27A Bearing Cover – Outboard 1 043071 2 Adjusting Screw – R/V 1 433909 28 Capscrews – Bearing Cover 4 4 - 8 920080 3 Locknut – Adjusting Screw 1 922923 35 Shaft Key 1 1 909125 4 Cover – R/V 1 413076 41 Liner – LGRL(F)1.25 [8 - Vane Only] 1 2 183019 7 Spring Guide – R/V 1 423955 Liner – LGL(F)1.25 [8 - Vane Only] 2 183020 8 Spring – R/V (81 – 125 psi) 1 471428 Liner – LGL(F)1.5 [8 - Vane Only] 2 183310 9 Valve - R/V 1 453077 71 Disc 2 1 063075 10 O-Ring – R/V Cover 1 1 711924 72 O-Ring – Head 2 1 701918 12 Casing with feet (1.25) 1 013075 73 Gage Plug (1/4”) 1 908198 Casing with feet (1.5) 013376 73A Gage Plug (3/4”) 1 6 908225

13 Rotor & Shaft Assembly, Eight 1 2 262300 74 Setscrew – Liner 1 922088 Vane (with Ref. Nos. 24A & 24B) 76 Grease Fitting 2 317815

14 Vane – Duravane 8 1 093088 76A Grease Relief Fitting 2 701992 20 Head 2 033073 88 O-Ring – R/V Cap 1 1 701949 21 Capscrews – Head 16 920276 104 Grease Seal 1 1 331927 24 Ball Bearing 2 1 903114 — Tool - Locknut — 903090

24A Locknut – Bearing 2 2 903534 — Kit - Maintenance [8 Vane] — 898976 24B Lockwasher – Bearing 2 1 903533 — Kit - Rebuild LGRL(F)1.25(A) [8 Vane] — 899076 26 Gasket - Bearing Cover 3 1-2 1 383075 — Kit - Rebuild LGL(F)1.25(A) [8 Vane] — 899077 27 Bearing Cover – Inboard 5 0-1 043070 — Kit - Rebuild LGL(F)1.5(A) [8 Vane] — 899078

1 Included in Maintenance Kits and Rebuild Kits 2 Included in Rebuild Kits. 3, 4, 5 Applies to LG(R)LF pump models only: 3 Use one outboard 4 Use four outboard 5 Use none. 6 Ref. No. 73A: Older pumps may use a 1/4” plug (pn 908198) or 1/2” plug (pn 908215). 7 See opposite side re parts for older pumps fitted with a 4-vane rotor. Note: Earlier model pumps used taper pins, which are no longer required. Keep this parts list with Installation, Operation and Maintenance Instructions.

4-Vane Rotor 7

LOCKNUT TOOL


BLACKMER PuMP PARTS PUmP modElS lGR1.25, lGRlF1.25A, lGl1.25, lGlF1.25A, lGl1.5, lGlF1.5A (continUEd)

H

FLANGE ‘F’ MOUNTING

Ref. No. Description Partsper

PumpPart No.

Casing without Feet – LG(R)LF1.25 013077 12A

Casing without Feet – LGLF1.5 1

013377 26 Gasket - Bearing Cover 1 383075

28A Bracket Mounting Screws 4 920101 28C Guard Screw 1 920026

Coupling Half – Pump 906147 Coupling Spider 906155 Coupling Half – Motor (56C) 906151 Coupling Half – Motor (143TC,145TC,184C)

906147 34

Coupling Half – Motor (182TC,184TC,215C)

1

906146

56 Capscrews – Adapter Ring Mounting 4 920480 76 Grease Fitting 1 317815

76A Grease Relief Fitting 1 701992

86Motor Adapter Ring-182TC,184TC,215C

1 832914

104 Grease Seal 1 331927

108 6 Mounting Bracket Includes Ref. Nos. 76 & 76A

1 832912

108B Capscrews - Bracket 4 920331 186 Guard 1 804120

6 Use (P/N 833000 – Mounting Bracket w/ feet) on discontinued models LG(R)LF1.25 and LGLF1.5

MECHANICAL SEAL

Ref. No.

Part Name PartsPer

PumpPart No.

153 Mechanical Seal Assembly 2 1 333045

153A Stationary Seat ( Hardened Steel ) 2 **

153B Seal Face ( Carbon ) 2 **

153C Jacket Assembly 2 **

153D O-Ring – Stationary (Buna-N) 2 711916

153E O-Ring – Rotating (Buna-N) 2 711915 1 Included in Maintenance Kits and Rebuild Kits ** NOTE: Mechanical Seal Ref. No. 153 is only sold as a complete assembly. Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts.

4-VANE ROTOR/SHAFT PARTS

Ref. No.

Part Name PartsPer

PumpPart No. Part Name Part No.

13A Rotor & Shaft Assembly, Four Vane 1 2 263076 Kit – Maint LGRL(F)1.25A [4 Vane] 898917 (Includes Ref. Nos. 24A & 24B) Kit - Maint LGL(F)1.25(A) [4 Vane] 898918

14 Vane – Duravane 4 1 093088 Kit - Maint LGL(F)1.5(A) [4 Vane] 898919 Liner – LGRL(F)1.25 [4 - Vane Only] 2 183003 Kit - Rebuild LGRL(F)1.25A [4 Vane] 899017

41A Liner – LGL(F)1.25 [4 - Vane Only] 1 2 183004 Kit - Rebuild LGL(F)1.25(A) [4 Vane] 899018 Liner – LGL(F)1.5 [4 - Vane Only] 2 183301 Kit - Rebuild LGL(F)1.5(A) [4 Vane] 899019 Push Rod – LGRL(F)1.25 1 123004

77 Push Rod – LGL(F)1.25 2 1 123076 Push Rod LGL(F)1.5 1 123401

- 76 -CONYERS, GA (800) 241-5652


BLACKMER PuMP PARTS

BLACKMER PARTS LIST PUMP MODELS: LGLD2E, LGL2E, LGLD3E, LGL3E

See Instructions 501-C00 for Installation, Operation and Maintenance

Ref. No.

Description Parts Per

Pump

Size 2 Part No.

Size 3 Part No.

Ref. No.

Description Parts Per

Pump

Size 2 Part No.

Size 3 Part No.

4 Cover - Relief Valve (R/V) 1 414401 415113 35 Key - Shaft 1 1 909130 1 9091305 Capscrews - R/V Cover 6 920331 920331 41 Liner 1 2 184405 2 1851118 Spring - R/V 1 471423 475135 Flange - NPT 654401 6551129 Valve - R/V 1 454405 455129

42 Flange - Weld

2 654405 655102

10 O-Ring - R/V Cover 1 1 701919 1 701925 42A O-Ring - Flange 2 1 702004 1 70200212 Casing 1 014405 015127 Capscrew - NPT Flange 920384 92054713 Rotor & Shaft Asy. - LGL 1 264443 265149

42B Capscrew - Weld Flange

8 920351 920510

(Includes Ref. Nos. 24A & 24B) 71 Disc 2 1 064412 1 06511213A Rotor & Shaft Asy. ñ LGLD 5 1 2 264445 2 265148 72 O-Ring - Head 2 1 702022 1 702041

(Includes Ref. Nos. 24A & 24B) 73 Gage Plug 2 908198 90819814 Vane - Duravane (Std.) 6 1 091419 1 095131 74 Key ñ Liner 1 2, 6 183991 2 18519120 Head 2 034416 035128 76 Grease Fitting 2 317815 31781521 Capscrews - Head (Size 2) 32 920351 N/A 76A Grease Relief Fitting 2 701992 701992

Capscrews - Head (Size 3) 40 N/A 920369 77 Push Rod 3 1 123905 1 12510524 Ball Bearing 2 1 903156 1 903172 104 Grease Seal 1 1, 3 331918 1, 3 331908

24A Locknut - Bearing 2 2 903521 2 903523 123A Dirt Shield 1 1, 3 701480 N/A 24B Lockwasher - Bearing 2 1 903522 1 903524 Shaft Protector 26 Gasket - Bearing Cover 2 1 383940 1 385125

186 (LGLD Models Only)

1 341601 341801

27 Bearing Cover (Inboard) 3 1 041431 041815 ó Tool - Locknut ó 903091 90309127A Bearing Cover (Outboard) 4 1 041433 041817 ó Kit ñ Maintenance ó 898979 89898128 Capscrews - Bearing Cover 8 - 12 920285 920285 ó Kit ñ Rebuild ó 899079 899081

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit The following applies to double end shaft pump models LGLD2E, LGLD3E: 3 Use Two 4 Use None 5 Double-Ended Rotor & Shaft. 6 Pump models before 1995 require key 184407. Keep this parts list with Installation, Operation and Maintenance Instructions.

LOCKNUT TOOL

H


MECHANICAL SEAL ñ NH3 OR DUAL SERVICE ñ SNCN (ID Code = QA)

Ref. No.

Part Name Parts Per

Pump

Size 2 Part No.

Size 3 Part No.

153 Mechanical Seal Assembly 2 1 334439 1 335225153A Stationary Seat (Steel) 2 ** ** 153B Seal Face (Carbon) 2 ** ** 153C Jacket Assembly 2 ** ** 153D O-Ring - Stationary (Buna-N) 2 711924 702025153E O-Ring Rotating (Buna-N) 2 711918 711912

1 Included in Maintenance Kit and Rebuild Kit ** NOTE: Mechanical Seal Ref. No. 153 is only sold as a complete assembly. Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts. OPTIONAL HYDRAULIC MOTOR ADAPTER PARTS

Ref. No. Part Name Parts Per

Pump Size 2

Part No.Size 3

Part No.See Below Hydraulic Motor Adapter Kit * See Below 894425 895140

26A Gasket- Hydraulic Motor Adapter 1 383940 381817 28A Capscrew ñ Hydraulic Motor Adapter / Head 4 / 6 920369 920369

34 Coupling w/ Setscrew ñ 1.25î straight key hydraulic motor shaft 1 906967 906967

35 Key ñ Coupling 1 909184 909184 76 Grease Fitting 1 317185 317815

76A Grease Relief Fitting 1 701992 701992 135 Hydraulic Motor Adapter ñ SAE A Flange 1 041827 041831

135A Capscrew ñ Adapter / Motor 2 920510 920510 * Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two piece design ñ refer to page 206-C00.

LGLD2E LGLD3 E

BLACKMER PuMP PARTS PUmP modElS: lGld2E, lGl2E, lGld3E, lGl3E (continUEd)

H

- 78 -CONYERS, GA (800) 241-5652


BLACKMER PuMP PARTS

BLACKMER PARTS LIST PUMP MODELS: LGLD4A, LGL4A

DISCONTINUED MODELS: LGL4, LGLD4(See Instructions 501-E00 for Installation, Operation and Maintenance)

`

Ref.No. Description

PartsPer

PumpPart No. Ref.

No. Description PartsPer

PumpPart No.

1 Cap - Relief Valve (R/V) 1 413952 28 Capscrews - Bearing Cover 12 920286 2 Adjusting Screw - R/V 1 NOTE 3 35 Key – Shaft 1 1 909183 3 Locknut - Adjusting Screw 1 NOTE 3 41 Liner 1 2 182000 4 Cover - R/V 1 412001 Flange - 3" NPT 652012 5 Capscrew - R/V Cover 4 920663 Flange - 3" Weld 652007 7 Spring Guide - R/V 1 426355

42Flange - 4" Weld

1 - 2 652005

8 Spring - R/V 1 NOTE 3 42A O-Ring - NPT, Weld Flange 2 1 701937 9 Valve - R/V 1 452001 Capscrew - NPT Flange 920663

10 O-Ring - R/V Cover 1 1 70194642B

Capscrew - Weld Flange 8

92064012 Casing 1 NOTE 3 71 Disc 2 1 062039

71A Machine Screw - Disc 8 2 920015 Rotor & Shaft Asy, Dbl. End - LGLD4(A) (Includes Ref. No. 24A & 24B)

2 26202471B* Lockwasher - Machine Screw 8 2 909634 72 O-Ring - Head 2 1 702039

13Rotor & Shaft Asy, Sgl. End - LGL4(A) (Includes Ref. No. 24A & 24B)

1262023

73 Gage Plug 2 908198 14 Vane - Duravane (Std.) 6 1 092019 74 Key - Liner 1 2 182040 20 Head 2 032039 76 Grease Fitting 2 317815 21 Capscrews - Head 36 920532 76A Grease Relief Fitting 2 701992 24 Ball Bearing 2 1 903172 77 Push Rod 3 1 122005

24A Locknut – Bearing 2 2 903541 88 O-Ring - R/V Cap 1 1 701926 24B Lockwasher – Bearing 2 1 903542 Grease Seal – LGLD4(A) 2 26 Gasket - Bearing Cover 2 1 385125

104Grease Seal – LGL4(A) 1

1 331908

Bearing Cover – LGLD4(A) 2 186 Shaft Protector (LGLD4 Only) 1 341801 27Bearing Cover – Inboard, LGL4(A) 1

041815 Tool - Locknut 903092

27A Bearing Cover – Outboard, LGL4(A) 1 041817 Kit - Maintenance 898922 Kit - Rebuild 899022

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit Note 3 – See Table on other side for proper parts. Keep this parts list with Installation, Operation and Maintenance Instructions.

LOCKNUT TOOL

H


BLACKMER PuMP PARTS PUmP modElS: lGld4A, lGl4A, lGl4, lGld4 (continUEd)

MECHANICAL SEAL - STANDARD

Ref.No. Part Name

PartsPer

PumpPart No.

153 Mechanical Seal Assembly 2 1 332050 153A Stationary Seat (Hardened Steel) 2 **153B Seal Face (Carbon) 2 **153C Jacket Assembly 2 **153D O-Ring - Stationary (Buna-N) 2 701934153E O-Ring - Rotating (Buna-N) 2 711912

1 Included in Maintenance Kit and Rebuild Kit** NOTE: Mechanical Seal Ref. No. 153 is only sold as a complete assembly. Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts.

Use the table below to determine the proper parts for each model. LGLD4A and LGL4A Discontinued LGLD4 and LGL4 Ref.

NoPart Name Parts Per

Pump Part No. Part No. 2 Adjusting Screw - R/V 1 436310 436307 3 Locknut - Adjusting Screw 1 432039 436355 8 Spring - R/V 1 472039 476305 12 Casing 1 012009 012000

Use Dimension ‘A’ as shown in the drawing to determine the pump model number. The pump model number will also be shown on the nameplate.

Model Dim ‘A’ LGLD4A, LGL4A 2.19 in. 5.56 cm.

LGLD4, LGL4 1.75 in. 4.45 cm.

HYDRAULIC MOTOR ADAPTER PARTS

REF.NO. PART NAME

PARTS PER

PUMPPART NO.

SeeBelow Hydraulic Motor Adapter Kit * See

Below 892037

26A Gasket – Hydraulic Motor Adapter 1 381817

28A Capscrew – Hydraulic Motor Adapter / Head 6 920369

34 Coupling w/ Setscrew – 1.25” straight key hyd. motor shaft 1 906970

35 Key – Coupling 1 909184 76 Grease Fitting 1 317815


135 Hydraulic Motor Adapter – SAE A Flange 1 041829

135A Capscrew – Adapter / Motor 2 920510 * Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were a two piece design – refer to page 206-C00.

H

- 80 -CONYERS, GA (800) 241-5652


BLACKMER PuMP PARTS

BLACKMER PARTS LIST PUMP MODEL: TLGLF3C

See Instructions 501-D00 for Installation, Operation and Maintenance

Ref.No. Description

PartsPer

PumpPart No. Ref.


PumpPart No.

4 Cover - Relief Valve (R/V) 1 415108 O-Ring – Flange 2 1/2” x 2 3/4” 2 1 701919 5 Capscrew - R/V Cover 6 920331

42AO-Ring – Flange 2 5/8” x 2 7/8” 2 1,3702004

8 Spring - R/V 1 4 471428 42B Capscrew - Flange, Flanged Elbow 8 920491 9 Valve - R/V 1 4 451417 71 Disc 2 1 065121 10 O-Ring - R/V Cover 1 1 701919 72 O-Ring - Head 2 1 711923 12 Casing 1 015128 73 Gage Plug 2 908198 13 Rotor & Shaft Assembly 5 1 2 265147 74 Key - Liner 1 2 185193 14 Vane - Duravane 6 1 095132 76 Grease Fitting 2 317815 20 Head 2 035132 76A Grease Relief Fitting 2 701992 21 Capscrews - Head 36 920351 77 Push Rod 3 1 121607 24 Ball Bearing 2 1 903156 104 Grease Seal 2 1 331918

24A Locknut - Bearing 2 2 903521 123 Dirt Shield 2 1 701480 24B Lockwasher - Bearing 2 1 903522 186 Shaft Protector 1 341601 26 Gasket - Bearing Cover 2 1 383940 — Tool - Locknut 903091 27 Bearing Cover 2 041431 — Kit – Maintenance — 898980 28 Capscrews - Bearing Cover 8 920285 — Kit – Maintenance with R/V — 899225 35 Key - Shaft 1 1 909130 — Kit – Rebuild — 899080 41 Liner 1 2 185101 — Kit – Rebuild with R/V — 899125 Flange - 2" NPT 652010

42 Flange - 2" Weld 1-2 652024 Flanged Elbow - 2" NPT 655100 Flanged Elbow - 2" Weld 655109

Keep this parts list with Installation, Operation and Maintenance Instructions. 1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit 3 Larger O-Ring introduced October 2002 4 Additional parts Included in Kits with R/V 5 Includes Ref. No. 24A & 24B

LOCKNUT TOOL

H


BLACKMER PuMP PARTS

H

PUmP modEl: tlGlF3c (continUEd)

- 82 -CONYERS, GA (800) 241-5652


BLACKMER PARTS LIST PUMP MODEL: TLGLF4A DISCONTINUED MODEL: TLGLF4

(See Instructions 501-E00 for Installation, Operation and Maintenance)

Ref. No. Description

PartsPer

PumpTLGLF4A Part No.

TLGLF4 Part No.


PartsPer

PumpTLGLF4A Part No.

TLGLF4 Part No.

1 Cap - Relief Valve (R/V) 1 413952 413952 42A O-Ring - Flange 1 701937 701937 2 Adjusting Screw - R/V 1 436310 436307 42B Capscrew - 3" NPT Flange 4 920663 920663 3 Locknut - Adjusting Screw 1 432039 436355 Capscrew - 3", 4" 920640 920640 4 Cover - R/V 1 412001 412001 Weld Flange; Blank Flange 5 Capscrews - R/V Cover 4 920663 920663 TWIN DISCHARGE PORT OPTIONS7 Spring Guide - R/V 1 426355 426355 43 Flange - 2" NPT 2 652010 652010 8 Spring - R/V 1 472039 472039 Flange - 2" Weld 652024 652024 9 Valve - R/V 1 452001 452001 43A O-Ring - 2" Flange 21/2” x 23/4” 2 1 701919 701919

10 O-Ring - R/V Cover 1 1 701946 701946 O-Ring - 2" Flange 25/8” x 27/8” 2 1,3 702004 702004 12 Casing 1 012039 012039 43B Capscrew - Discharge Flange 8 920491 920491 13 Rotor & Shaft Asy. 1 2 262024 262022 71 Disc 2 1 062039 062039

(includes Ref. No. 24A & 248) 71A Machine Screw - Disc 8 2 920015 920015 14 Vane - Duravane (Std.) 6 1 092019 092019 71B Lockwasher - Machine Screw 8 2 909634 909634 20 Head 2 032039 032039 72 O-Ring - Head 2 1 702039 702039 21 Capscrews - Head 36 920532 920532 73 Gage Plug 2 908198 908198 24 Ball Bearing 2 1 903172 903172 74 Key - Liner 1 2 182040 182040

24A Locknut - Bearing 2 2 903541 903523 76 Grease Fitting 2 317815 317815 24B Lockwasher - Bearing 2 1 903542 903524 76A Grease Relief Fitting 2 701992 701992 26 Gasket - Bearing Cover 2 1 385125 385125 77 Push Rod 3 1 122005 122001 27 Bearing Cover 2 041815 041815 88 O-Ring - R/V Cap 1 1 701926 701926 28 Capscrews - Bearing Cover 12 920286 920286 104 Grease Seal 2 1 331908 331908 35 Key - Shaft 1 1 909183 909183 186 Shaft, Protector 1 341801 341801 41 Liner 1 2 182000 182039 Tool - Locknut 903092 903091

AUXILIARY INTAKE OPTIONS Kit - Maintenance 898922 N/A 42 Flange - 3" NPT 1 652012 652012 Kit - Rebuild 899022 N/A

Flange - 4" Weld 652005 652005Flange - 3" Weld 652007 652007Flange - Blank 652000 652000

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit 3 Larger O-Ring introduced October 2002 Keep this parts list with Installation, Operation and Maintenance Instructions

LOCKNUT TOOL

Discontinued Models Parts availibility may be limited.

BLACKMER PuMP PARTS

H


MECHANICAL SEAL Ref. No. Part Name Parts Per

Pump Part No.

153 Mechanical Seal Assembly 2 1 332050 153A Stationary Seat (Hardened Steel) 2 ** 153B Seal Face (Carbon) 2 ** 153C Jacket Assembly 2 ** 153D O-Ring - Stationary (Buna-N) 2 701934 153E O-Ring - Rotating (Buna-N) 2 711912

1 Included in Maintenance Kit and Rebuild Kit ** NOTE: Mechanical Seal Assy. (Ref. 153) is only sold as a complete assembly. Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts.

TLGLF4 TLGLF4AInterchangeability status w/TLGLF4A Interchangeability status w/TLGLF4 Part Name PART NO. REF. PART NO. REF.

Push Rods 122001 c 1 122005 c Liner 182039 c 2 182000 b Rotor & Shaft 262022 c 2 262024 a Bearing Locknut 903523 c 2 903541 c Bearing Lockwasher 903524 c 1 903542 c

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit Reference: a = Interchangeable, but requires new Bearing Locknuts PN 903541 and Bearing Lockwasher PN 903542. These are included whe ordering Rotor & Shaft PN 262024. b = Interchangeable but requires new push rods PN 122005. c = Not Interchangeable

OPTIONAL HYDRAULIC MOTOR ADAPTER PARTS

Ref.No. Part Name

PartsPer

PumpPart No.


Below 892037







135A Capscrew – Adapter / Motor 2 920510

* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two piece design – refer to page 206-C00.

BLACKMER PuMP PARTS PUmP modEl: tlGlF4A, tlGlF4 (continUEd)

H

- 84 -CONYERS, GA (800) 241-5652


BLACKMER PuMP PARTS

BLACKMER PARTS LIST PUMP MODEL: TLGLF4B

(See Instructions 501-E00 for Installation, Operation and Maintenance)


PartsPer

PumpPart No. Ref.


PumpPart No.

1 Cap - Relief Valve (R/V) 1 413952 42A O-Ring - Flange 1 701937 2 Adjusting Screw - R/V 1 436310 42B Capscrew - 3" NPT Flange 4 920663 3 Locknut - Adjusting Screw 1 432039 Capscrew - 3", 4" 920640 4 Cover - R/V 1 412001 Weld Flange; Blank Flange 5 Capscrews - R/V Cover 4 920663 TWIN DISCHARGE PORT OPTIONS7 Spring Guide - R/V 1 426355 43 Flange - 2" NPT 2 652010 8 Spring - R/V 1 472039 Flange - 2" Weld 652024 9 Valve - R/V 1 452001 43A O-Ring - 2" NPT Flange 0 - 2 1 701919 10 O-Ring - R/V Cover 1 1 701946 O-Ring - 2" Weld Flange 0 - 2 1 702004 12 Casing 1 012041 43B Capscrew - Discharge Flange 8 920491 13 Rotor & Shaft Asy. 1 2 262041 71 Disc 2 1 062039 (includes Ref. No. 24A & 24B) 71A Machine Screw - Disc 8 2 920015

14 Vane - Duravane (Std.) 6 1 092019 71B Lockwasher - Machine Screw 8 2 909634 20 Head 2 032041 72 O-Ring - Head 2 1 702039 21 Capscrews - Head 28 920532 73 Gage Plug 2 908198 24 Ball Bearing 2 1 903166 74 Key - Liner 1 2 182040

24A Locknut - Bearing 2 2 903541 76 Grease Fitting 2 317815 24B Lockwasher - Bearing 2 1 903542 76A Grease Relief Fitting 2 701992 26 Gasket - Bearing Cover 2 1 385125 77 Push Rod 3 1 122009 27 Bearing Cover 2 041815 88 O-Ring - R/V Cap 1 1 701926 28 Capscrews - Bearing Cover 12 920286 104 Grease Seal 2 1 331908 35 Key - Shaft 1 1 909183 186 Shaft, Protector 1 341801 41 Liner 1 2 182000 Tool - Locknut 903092

AUXILIARY INTAKE OPTIONS Kit – Maintenance 899224 42 Flange - 3" NPT 1 652012 Kit – Rebuild 899124

Flange - 4" Weld 652005 Flange - 3" Weld 652007 Flange - Blank 652000

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit

Keep this parts list with Installation, Operation and Maintenance Instructions

LOCKNUT TOOL

H


BLACKMER PuMP PARTS

MECHANICAL SEAL Ref. No. Part Name Parts Per

Pump Part No.

153 Mechanical Seal Assembly 2 1 332050 153A Stationary Seat (Hardened Steel) 2 ** 153B Seal Face (Carbon) 2 ** 153C Jacket Assembly 2 ** 153D O-Ring - Stationary (Buna-N) 2 701934 153E O-Ring - Rotating (Buna-N) 2 711912

1 Included in Maintenance Kit and Rebuild Kit ** NOTE: Mechanical Seal Assy. (Ref. 153) is only sold as a complete assembly. Ref. Nos. 153A, 153B & 153C are not available as separate replacement parts.

TLGLF4 TLGLF4AInterchangeability status w/TLGLF4A Interchangeability status w/TLGLF4 Part Name PART NO. REF. PART NO. REF.

Push Rods 122001 c 1 122005 c Liner 182039 c 2 182000 b Rotor & Shaft 262022 c 2 262024 a Bearing Locknut 903523 c 2 903541 c Bearing Lockwasher 903524 c 1 903542 c

1 Included in Maintenance Kit and Rebuild Kit 2 Included in Rebuild Kit Reference: a = Interchangeable, but requires new Bearing Locknuts PN 903541 and Bearing Lockwasher PN 903542. These are included whe ordering Rotor & Shaft PN 262024. b = Interchangeable but requires new push rods PN 122005. c = Not Interchangeable

OPTIONAL HYDRAULIC MOTOR ADAPTER PARTS

Ref.No. Part Name

PartsPer

PumpPart No.


Below 892037







135A Capscrew – Adapter / Motor 2 920510

* Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were of a two piece design – refer to page 206-C00.

PUmP modEl : tlGlF4b (continUEd)

H

- 86 -CONYERS, GA (800) 241-5652


Compressors, Hydraulic Drive, Motors, StartersCOMPRESSORS/MOTORS

KECF212ExPLOSION PROOFFLExIBLE CONNECTORFor connecting wir ing to motor on a pump unit so motor can be adjusted 3/4” x 12”

coMPressors Motors/starters/switcHes

ExPLOSION PROOF MOTORSClass 1, Group D (60 cycle), 1750 RMP

Item # Approx. Liquid Transfer Rate Motor SizeLB161 90 GPM @ 780 RPM 7.5 HPLB361 194 GPM @ 780 RPM 15 HPLB601 351 GPM @ 790 RPM 25 HPLB942 640 GPM @ 750 RPM 40 HP

BLACKMER OIL-FREE COMPRESSORSBlackmer offers a variety of factory assembled compressor packages to fit most application requirements. Standard base mounted units are available in a variety of styles.

KRuG HAND PuMPOperates on the simple principle of the automotive piston. used for filling 20# cylinders, lift truck cylinders, etc.Inlet: 1” FNPTOutlet: 3/4” FNPTCapacity: 6 GPM at 40 strokes/min.

Item # DescriptionKHP Hand pumpK-HP-HK Connecting hose kit

KRuG VAPOR COMPRESSORS• Has LP Gas fueled engine (uses LP

being transferred as fuel)• 20 GPM transfer rate• 1/2” FNPT connections

Item # Description K-VP-LP Compressor with LP engine K-VP-HK Connecting hose kit k25459B Replacement Compressor K209870 3/4” replacement clutch K3x927 Replacement pulley

ExPLOSION PROOFSTARTERSClass 1, Group D (60 cycle)NEMA Type 3R, 7, & 9

MAGNETIC STARTERS are designed for full voltage starting of motors. All Bulletin 509 starters are equipped with manual reset overload relays and may be operated by remote push button control. Protects motor from thermal overload and undervoltage. Push button in cover.

Item # Size Voltage Phase Max HPB509BHxD-1 1 115 1 2B509BHxA-1 1 230 1 3B509xHxD-1 1P 115 1 3B509xHxA-1 1P 230 1 5B509BHA-1 1 230 3 71/2B509BHB-1 1 460 3 10B509CHA-1 2 230 3 15B509CHB-1 2 460 3 25

Item # HP Phase Voltage AxPD010C1B* 1 1 115/230 AxPD015C1B* 1 1/2 1 115/230 AxP015C3B* 1 1/2 3 230/460 AxP020T3B 2 3 230/460 AxPB03T1B 3 1 230 AxP030T3B 3 3 230/460 AxPD05T1B 5 1 230 AxP050T3B 5 3 230/460 AxP075T3B 7 1/2 3 230/460 AxP100T3B 10 3 230/460 AxP150T3B 15 3 230/460 AxP250T3B 25 3 230/460*C-Face Mount

LOVEJOY COuPLINGS0300010 - 7/8” L0950300020 - 1 1/8” L0950300060 - spider for L095

H

PORTABLE LIQuID TRANSFER, VAPOR RECOVERY SYSTEMS FROM BLACKMERCustom skid mounted compressor units offer flexibility for transferring liquids in remote locations or emergency situations.

These units are customized to fit your specific needs.


StARtERS/SWitcHES (continUEd)90028-1011” LIQuID PROPANE METERDesigned for metering small quantities of liquid propane into portable containers and engine fuel tanks. Complete with strainer, vapor eliminator, & differential valves.Flow Range: 3 to 18 gpm.

VEEDER-ROOT PRINTING REGISTERReplace your Neptune register with a long lasting Veeder-Root Register

ITEM# DESCRIPTIONL789002-002 Printing RegisterL886201-001 Adaptor to fit 1 1/4” to 2” Neptune without ATCL886205-001 Adaptor to fit 1 1/4” to 2” Neptune with ATC

STARTERS/METERSManual Starters, Liquid & Vapor Meters

M250TC METRIS VAPOR METERThis 3/4” meter will meter 400,000 BTu at 11” w.C. and up to 1,200,000 BTu of 5 psig inlet pressure (max.). It has a direct read CFu index. 3/4” connections. Larger sizes are available.

K1222Toggle switch only for KxS52C.

E4000 - NEPTuNE ELECTRONIC REGISTERReplace your Bobtail’s Neptune or Veeder-Root mechanical register with this easy to use electronic register.

• To install an E4000 on a 1 1/2” Neptune meter, use a 201072-001 1 1/2” adaptor plate.

• To install an E4000 on a LC meter, you need: 1000678 Kit LC499988 Strainer cover LC81256 Thermowell LC06854 O-ring

Meters

mEtERS (continUEd)

MANuAL STARTERS

Designed for use where remote control is not required and where undervoltage protection is not needed. The motor is started at full line voltage. Thermal type overload protection is provided. START/STOP push buttons in cover.

Item # Size Voltage Phase Max HP 115V 230V 460VB609AHx 0 115/230 1 1 2 --B609BHx 1 115/230 1 2 3 --B609xHx 1P 115/230 1 3 5 --B609AHw 0 230/460 3 -- 3 5B609BHw 1 230/460 3 -- 7 1/2 10Class 1, Group D (60 Cycle) NEMA Type 3R, 7 and 9

B800H-2HA7REMOTE PuSH BuTTON STATIONProvides remote operation of magnetic startersClass 1, Group D (60 Cycle) NEMA Type 3R, 7 and 9

KxS52C OFF/ON SwITCHFor use with 1 and 1-1/2 HP explosion proof motors.

Class 1, Group D (60 Cycle) NEMA Type 3R, 7 and 9

EPSON SLIP PRINTERTM-u295-071

METER SEALS Item # Description 163-057-510 18” Seal wire 163-057-510S 18” Seal wire with lead seals

NEPTuNE CORIOLIS MASS FLOw LIQuID METERSFor bulk plants and bobtails. The Coriolis reduces LP Gas under-measurement, and compared to traditional mechanical flow meters, the Coriolis offers better accuracy with higher flow rates over a longer service life. when combined with the Neptune E4000 Register, the Coriolis allows an upgrade path not obtainable with competitive electronic transaction management systems. Features electronic temperature compensation and the availability of combining with hand helds. Available in sizes from 12 - 70 GPM.

H

833-ORMREMANuFACTuRED SCHLuMBERGER/NEPTuNE 833 PRINTER REGISTER1 Year or 1 Mill ion Gallon warranty (whichever comes first). Rebuilt 833 registers provide you with the same quality measurement and reliability that you have grown accustom to!Total ly rebui l t , recondit ioned and repainted units. All parts are inspected and any defect will be completely corrected.

- 88 -CONYERS, GA (800) 241-5652


Neptune & Liquatech Meter PartsMETER PARTS

nEpTunE/liquA-TECH METEr pArTs

DESCRIPTIoN PART #

3/4” and 1” Meter 3/4” 1”Gasket, Main Case L4861-016 L4861-016Measuring Chamber, Complete L42075-101 L42075-101Gasket, O-Ring, Vapor Release Cover L100139-012 L100139-012Strainer Assembly L100683-001 L100683-001Seal, Differential Valve, u-Cup L100025-008 L100025-008O-Ring, Inlet/Outlet, Differential Valve L100139-007 L100139-007Differential Valve Repair Kit L100028-011 L100028-011 1 1/4”, 1 1/2”, and 2” Meter 1 1/4” 1 1/2” 2” Stud, Register Mounting L84435-000 L84435-000 L84435-000Gasket, Main Case L4862-008 L4862-008 L84806-000Measuring Chamber, Complete L43260-101 L83271-101 L45806-101Star Connection L82976-001 L82976-001 L82976-001Gear Train, Complete L83501-000 L84981-000 L83502-000Seal, u-Cup Shaft L100025-002 L100025-002 L100025-002

Vapor Release and Strainer 1 1/2” 2”Gasket, O-Ring. Vapor Release Cover L100139-022 L100139-022Main Valve, Complete L89274-006 L89274-006Piston, Seal L83179-000 L83179-000Float, Complete L82476-001 L82476-001Strainer and Gasket Assembly L101433-704Strainer, Inner and Outer Combo L101462-003Inlet Check Valve, Complete L84983-704 L84813-702Gasket, O-Ring, Strainer Cover L100139-010 L84818-000

Differential Valve 1 1/2” 2”Diaphragm L83771-002 L83771-002O-Ring L100139-001 L100139-001Gasket, Flange L82060-000 L84818-000

Temperature Compensator 1 1/4” 1 1/2” 2”Gear Train, Complete L83501-000 L84981-000 L83502-000Seal, u-Cup Shaft L100025-002 L100025-002 L100025-002Adapter unit, Complete L86602-005 L86602-005 L86602-005Stud, Regoster Mounting L84435-000 L84435-000 L84435-000Rollpin L100370-003 L100370-003 L100370-003Drive Fork L84192-006 L84192-006 L84192-006

Neptune Registers Part#600 Series Register (for 3/4” meter) 100498-009833 Printer Register 880030-000601 Series Register (for 1” meter) 100498-016

H

Documents

PUMPiNG systeMs PUmPinG SYStEmS (continUEd) · PDF fileCONYERS, GA (800) 241-5652 APOPKA, FL (800) 432-1869 GOLDSBORO, NC (800) 426-9293 - 69 - PUmPinG SYStEmS (continUEd) Vertical