There are many levels of protection and

system sophistication on offer to suit most

budgets from manual start petrol fire pumps

to remote start diesel units that can be

operated by mobile phone. This cost can be

incorporated into the purchaser's mortgage if

installed during the construction phase.

Small Farm Services uses

top quality components

and materials which

increase reliability and

reduce maintenance to a

minimum. Externally

mounted systems are available for existing

dwellings

Full technical support and servicing is offered by

Small Farm Services

The majority of house fires started by ember

attack, start in the gutters. Sprinkler systems

designed to protect buildings from ember attack

can be fitted to the roof, veranda's, decked areas

as well as under floor areas of pole style houses.

Perimeter sprinkler system can also be fitted.

The system efficiency can be substantially

increased when fitted during the construction

phase because larger poly tube can be used as

it can be concealed in the wall cavity and the

roof space.

If fitted during construction only a small amount of

copper tube is required where the sprinklers

project out through the roof sheeting which

reduces the installation cost and is very neat as

most of the pipe work is concealed.

1155 Hidden Valley Road Parkerville WA 6081 I Telephone: 0428 500 295 I Email: sfs1@westnet.com.au

Web: www.smallfarmservices.net.au

Small Farm Services

Benefits include:

Maximum water efficiency

Hidden Pipes and fittings

Remote control, with confirmation

text messages

No extra costs after build!

Activate your sprinkler system

by Mobile phone! 3G compatibleSPR IN NO KI LT EN RE SV YE SR TP E MER SIF

Install a

sprinkler system

while you build

or to your

existing home

Protect your home against fire

1155 Hidden Valley Road Parkerville WA 6081 I Telephone: 0428 500 295 I Email: sfs1@westnet.com.au

Web: www.smallfarmservices.net.au

Small Farm Services

SPR IN NO KI LT EN RE SV YE SR TP E MER SIF

Multi-Attempt Automatic

Smart Switch

DESCRIPTION

SFS01-V2

If the engine has not fired by the end of first attempt, the starter is turned off for a resting period. The sequence will then repeat up to a maximum number of start attempts. Following a successful start, sensed when the oil pressure switch changes its state, the start relay is de-energized and latched out to prevent re-engagement of the starter with the engine running.

The Model SFS01-V2 is a Multi-attempt Automatic Engine Smart Switch designed to automatically [remotely] or manually start and stop the engine. It will indicate the operational status and fault conditions, automatically shut down the engine and indicate the start engine failure by a flashing “ST. FAIL” LED as well as informing operator via SMS. Other functions and possible engine fault conditions are also visually shown via a set of LEDs located on the module.The SFS01-V2 is designed to receive start/stop commands from a specially coded SMS or via direct call from a control server (CS) phone number(s). It is capable of storing up to 10 CS numbers (index 0~9) giving you and your colleagues an equal opportunity to control your engine from any place on earth where mobile network is available. You won't be charged for a call from CS phone number because the module will hang up incoming call

START and RUN Sequence

Relay outputs are provided for:• Fuel Solenoid Output • Starter Motor OutputThe relays supply positive plant supply out.

Inputs are available for:• • Wired Remote Start [wire 1]• Battery –Ve [wire GR/Y]• Battery +Ve [wire 6] • W. Pressure switch [wire 4]

Low Oil Pressure [wire 3]

Lower PCB (green): engine controllerWarning lights [LEDs] provided to indicate the following: • • E. STOP LED [Active state of emergency stop switch and S/D]• LOW OIL LED [Low oil pressure alarm and S/D] • HET/GL LED [High engine temperature and S/D]/[Glow plug

energized]• SPEED LED [Over/under engine speed failure and S/D]• ON LOAD LED [Generator is on load]

Upper PCB (blue): 3G/GSM controller• Green LED (SRV): lit during handling commands / messaging.Red LED (ACT): flashing every second during network initialization

thand flashing 2 times every 5 second after successful network initialization

ST. FAIL LED [Unsuccessful start after multiple attempts and S/D]

Engine controller specificationDC Supply: 12VdcMax. Standby current: ~10mA @ 12 VNumber of attempts: 5Crank durations: 2-3-3-4-5 secPause between each attempt: 20 secHold-off timer* set for: 7 secStarter relay output: 10A maxFuel solenoid output 10A maxOperating Temperature Range: -20 to +55°C.Humidity: Less Than 80% RH

3G/GSM controller specificationDC Supply: 12VdcMax. standby current:~150mA / Average 50mAReceiver/transmitter: Integrated into SFS01-3G module.Working Frequencies: Dual-Band UMTS/HSDPA850/1900MHz Quad-Band GSM/GPRS/EDGE 850/900/1800/1900MHzSIM Card: Standard size SIM (3V & 1.8V)SIM card must be activated and inserted by a user into de-energised module before powering up the unit.

Important features

•

•

•

•

•

•

•

•

3G and GSM compatible

Can be operated by text or voice call

Can be turned ON and OFF repeatedly as required

Comes pre-wired with 5m harness

SFS01-V2 Module monitors the engine starting battery condition and reports any faults automatically

SFS01-V2 Module monitors engine oil pressure and water pump pressure and reports status automatically

Custom built units for special applications available

Operates completely independent of any scheme power supply and has inbuilt battery back up to maintain communication.

Custom built units can be produced for many special applications e.g. stock watering, water transfer, dewatering, frost control and many more so if you have a particular application email your

requirements or phone to discuss.