property damage! Retain instructions for future … · Dayton radial blade belt-driven blowers are used to move air and material. ... Wheel and housing are constructed of steel

Dayton® Radial BladeBelt-Driven Blowers

Operating Instructions & Parts Manual 3C106, 3C107, 3C108, 3C539 and 3C540

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/orproperty damage! Retain instructions for future reference.

Form 5S1429 Printed in U.S.A.058010107 /015 /VCPVP

DescriptionDayton radial blade belt-driven blowers are used to move air and material. Model 3C539handles long stringy materials such as: wood shavings, paper trim and fibrous materialssuch as: textile scrap, wool and ensilage. Models 3C106, 3C107, 3C108 and 3C540 handlegranular materials such as: sawdust, grain and particle-laden industrial process air or gases.

Wheel and housing are constructed of steel. Maximum inlet air temperature250°F (121°C).Assembled for bottom horizontal discharge and clockwise (CW) rotation. Standarddischarge positions can be changed in the field to either CW or CCW rotation, and any oneof sixteen standard discharge positions. See Figure 2. Baked-on gray polyester/epoxy.

PB-18972

Figure 1– Radial Blade Belt-Driven Blower

Not recommendedas an explosion

proof blower. Do not use whereexplosive fumes or gases are present.

®

ESPAÑOL

FRANÇAIS

ENGLISH

OPTIONAL HEAT SLINGEROptional aluminum split-type heat slingers,models 4C784, 4C790, 4C791 and 4C792extend maximum inlet air temperature to450°F when mounted to blower shaft. Inaddition, for blowers using a heat slinger, aheat shield can be installed between motorand housing allowing the maximum inlettemperature to increase to 500°F.

UnpackingAfter unpacking the blower, inspectcarefully for any damage that may haveoccurred during transit. Rotate wheel byhand to be sure it turns freely.

General Safety Information1.Follow all local electrical and safety

codes, as well as the National Electrical Code (NEC) and the Occupational Safety and Health Act (OSHA) in the United States.

2.Blower must be securely and adequately grounded. This can be accomplished by wiring with a grounded, metal-clad raceway system, by using a separate ground wire connected to the bare metal of blower frame, or other suitable means.

3.Always disconnect power source before working on or near a motor or its connected load. If the power disconnect point is out-of-sight, lock it in the open position and tag to prevent unexpected application of power.

4.Be careful when touching the exterior of an operating motor – it may be hot enough to be painful or cause injury. With modern motors, this condition is normal when operated at rated load and voltage – modern motors are built to operate at higher temperatures.

5.Protect the power cable from coming in contact with sharp objects.

6.Do not kink power cable and never allow the cable to come in contact with oil, grease, hot surfaces, or chemicals.

7.Make certain that the power source conforms to the requirements of your equipment.

8.When cleaning electrical or electronic equipment, always use an approved cleaning agent such as dry cleaning solvent.

9.Not recommended as an explosion proof blower. Do not use where explosive fumes or gases are present.

10. If blower is operated without an inlet or outlet duct, guard openings in accordance with OSHA regulations to prevent contact with rotating blower wheel.

2

Dayton Operating Instructions and Parts Manual

Dayton Radial Blade Belt-Driven Blowers

®

ENGLISH

3C106, 3C107, 3C108, 3C539 and 3C540

NOTES:1. Direction of rotation is determined from drive side of fan.2. For fan inverted for ceiling suspension, or side mounting,

direction of rotation and discharge is determined when fan is resting on floor.

3. Reprinted from AMCA, STD. 99-2406-83, with the express written permission from the Air Movement and Control Assoc. Int., Inc., 30 West University Dr., Arlington Heights, IL 60004-1893.

Figure 2 – Rotation and Discharge Positions

CounterclockwiseTop Angular Up

ClockwiseBottom Angular Down

CounterclockwiseBottom Angular Down

Clockwise Top Angular Down

Clockwise Bottom Angular Up

Clockwise Up Blast

ClockwiseDown Blast

ClockwiseTop Horizontal

ClockwiseTop Angular Up

ClockwiseBottom Horizontal

Counterclockwise Up Blast

Counterclockwise Top Horizontal

CounterclockwiseTop Angular Down

CounterclockwiseDown Blast

CounterclockwiseBottom Horizontal

Counterclockwise Bottom Angular Up

Models 3C106,3C107, 3C108,3C539 and 3C540

3


ENGLISH

®

Figure 3 – Dimensions

Dimensions

A B C D E F H J K L M N P Q R S T V X

3C539 121/4 13/16 0.27 18 1 7 6 13 161/4 89/16 75/8 95/8 95/8 213/4 61/8 71/4 83/8 105/8 43/16 233/8 9/16 16

3C106 155/8 13/16 0.44 171/4 1 9 71/2 175/8 141/2 111/16 911/16 123/16 1111/16 281/2 67/8 91/4 97/8 135/16 415/16 291/2 9/16 187/8

3C107 191/8 17/16 0.66 215/8 13/8 11 91/16 17 193/4 131/4 113/4 147/8 133/4 30 75/8 111/4 115/8 161/2 511/16 31 9/16 221/2

3C108 225/8 111/16 0.93 215/8 13/8 13 101/2 17 193/4 155/8 137/8 179/16 157/8 31 83/8 131/4 131/8 191/2 67/16 321/2 9/16 2211/16

3C540 261/8 115/16 1.24 251/2 7/8 15 121/8 221/2 231/4 181/8 161/16 205/16 191/16 363/16 93/16 151/4 161/4 221/2 93/8 401/2 11/16 25

RADIAL BLADE BELT-DRIVEN BLOWERWHEEL

DIA.

Dimensions (inches)

IN/OUTAREAINSQ.FT.

SHAFTDIA.MODEL

HEATSLINGER

(OPTIONAL)

V DIA.6 HOLES

4

ENGLISH



®

3C106, 3C107, 3C108, 3C539 and 3C540

Drive Data

Motor Blower Motor Sheave RMA Blower SheaveModel HP RPM Belt Pitch Dia. Belt Belt Pitch Dia. Grooves

3 3160 5.2 A A35• 5.7 A 1

3 3390 6.0 A A35 6.2 A 1

3C539 5 3685 5.4 B B33 5.1 B 1

5 3750 5.9 B B33 5.4 B 1

5 3870 4.9 B B30 4.4 B 2

3 2275 6.4 B B38 4.9 B 1

5 2460 7.9 B B42 5.6 B 1

5 2625 8.9 B B45 5.9 B 1

3C106 71/2 2815 4.9 B B38 6.1 B 2

71/2 2920 5.4 B B40• 6.4 B 2

10 3045 5.6 B B38 6.4 B 2

10 3180 5.4 B B38 5.9 B 2

10 3335 4.8 A A35 5.0 A 3

71/2 1990 5.8 B B43 5.1 B 2

71/2 2125 6.8 B B44 5.6 B 2

10 2270 7.0 B B45 5.4 B 2

3C107 10 2350 8.6 A A49 6.4 A 2

15 2460 9.0 A A48 6.4 A 3

15 2590 8.0 B B45 5.4 B 3

15 2715 9.0 B B47 5.8 B 3

10 1780 5.4 A A35 10.6 A 2

15 1880 8.6 B B51 8.0 A 2

3C108 15 1985 6.8 B B45 6.0 B 3

20 2090 6.6 B B53 11.0 B 3

20 2185 6.8 B B49 11.0 B 3

20 2250 9.0 B B50 7.0 B 3

15 1540 8.0 B B54 9.0 B 2

15 1630 8.0 B B54 8.6 B 2

20 1700 6.6 B B61 13.6 B 3

3C540 25 1795 6.4 B B58• 12.4 B 3

25 1860 8.6 B B53 8.0 B 3

25 1900 9.4 B B54 8.6 B 3

25 1950 9.0 B B54 8.0 B 3

(•) When using “Totally Enclosed” motors, these belt sizes will change. (3160 RPM = A33, 2920 RPM = B38 1795 RPM = B57.)

5

®

ENGLISH

Models 3C106,3C107, 3C108,3C539 and 3C540


Performance

Wheel 4" 5" 6" 7" 8" 9" 10" 11" 12" 13" Blower MotorModel Dia. SP SP SP SP SP SP SP SP SP SP RPM HP

121/4 1455 1290 1090 840 515 — — — — — 3160 3

121/4 # # 1340 1145 915 625 — — — — 3390 3

3C539 121/4 # 1740 1610 1455 1290 1080 840 515 — — 3685 5

121/4 # 1795 1660 1525 1360 1165 955 675 — — 3750 5

121/4 # # 1780 1650 1505 1330 1135 910 620 — 3870 5

155/8 # 1725 1430 960 — — — — — — 2275 3

155/8 2290 2050 1810 1540 1120 — — — — — 2460 5

155/8 # 2330 2115 1890 1630 1250 — — — — 2625 5

3C106155/8 2880 2665 2450 2250 2040 1795 1485 — — — 2815 71/2

155/8 # 2850 2630 2425 2230 2015 1765 1420 — — 2920 71/2

155/8 # # 2845 2645 2460 2260 2060 1810 1470 — 3045 10

155/8 # # # 2900 2720 2540 2360 2160 1930 1615 3180 10

155/8 # # # # # 2795 2620 2435 2245 — 3335 10

191/8 3345 2985 2620 2190 1490 — — — — — 1990 71/2

191/8 # 3430 3115 2765 2360 1735 — — — — 2125 71/2

191/8 4235 3900 3575 3260 2940 2560 2020 — — — 2270 10

3C107 191/8 # # 3840 3545 3245 2910 2515 1920 — — 2350 10

191/8 # 4420 4195 3900 3610 3315 3005 2605 2030 — 2460 15

191/8 # # # 4360 4075 3805 3530 3230 2875 2400 2590 15

191/8 # # # # 4380 4190 3935 3675 3395 3047 2715 15

225/8 # 4730 4260 3780 3170 2190 — — — — 1780 10

225/8 5750 5270 4810 4360 3855 3270 2315 — — — 1880 15

3C108225/8 # 5840 5390 4985 4550 4080 3535 2665 — — 1985 15

225/8 6700 6300 5910 5500 5100 4685 4240 3705 2955 — 2090 20

225/8 # # 6200 6050 5665 5270 4900 4475 3985 3260 2185 20

225/8 # # # # 5970 5585 5215 4835 4400 3885 2250 20

261/8 6925 6260 5635 4955 4135 — — — — — 1540 15

261/8 # # 6435 5830 5200 4385 3145 — — — 1630 15

261/8 # 7570 6980 6350 5840 5175 4370 — — — 1700 20

3C540 261/8 # 8200 7755 7185 6660 6080 5490 4735 3600 — 1795 25

261/8 # # 8110 7660 7130 6605 6065 5415 4580 — 1860 25

261/8 # # # # 7630 7105 6600 6045 5415 4400 1900 25

261/8 # # # # # 7420 6890 6380 5790 5040 1950 25

CFM AIR DELIVERY AT SPEED AND STATIC PRESSURE SHOWN (#)

(#) Motor overload. Not recommended for operation at this static pressure with this HP motor.

6


ENGLISH


®

3C106, 3C107, 3C108, 3C539 and 3C540

Installation1. Blowers are assembled for bottom

horizontal discharge. The discharge position can be changed to any one of its other discharge positions by removing the bolts between the supporting angles and the housing. Rotate to the desired position.

2. Make sure all bolts and screws are tightened before mounting on a rigid, flat, level foundation. Bolt the blower securely into position.

3. Check the interior of the fan housing to be sure it is free of debris. Rotate the wheel to insure that it is not rubbing or binding. Check the clearance of the wheel and the inlet cone. If rubbing exists, loosen the bolts on the cone and shift the cone until clearance is obtained. If still rubbing, loosen the set screw on the wheel and shift the wheel rearward to obtain clearance. Retighten the set screw.

Figure 4 –Correct Sheave Alignment

NOTE: Drive tension should berechecked after the first 50 to100 hours of operation.

FIXED SHEAVE

STRAIGHT EDGE

ADJUSTABLE SHEAVE

FIXED SHEAVE

STRAIGHT EDGE

4. Mount motor on motor base. Holes are provided to accommodate various frame size motors. Tighten motor to base with nuts, bolts, and lock washers.

5. Mount V-Belt drive and align motor and fan sheave. Tighten all set screws or bolts in the case of sheaves with bushings. Adjust the belt tension by raising or lowering the J-bolts on themotor base. Belts should be tighteneduntil the slack side can be depressedabout 3/4” for each foot of span between the pulleys.

6. All exposed moving parts must beproperly guarded as per the recom-mendations of the Occupational Safety and Health Act (OSHA) in the United States.

Electrical Hazard –Turn power off

before servicing. Lock it out.

Rotating Blades –Keep hands and

feet away from unguarded openings.

Do not operate fanwithout drive guard.

Stop fan from rotating prior to servicing.

Operation1. Before connecting the motor to the

electric supply, check the electrical characteristics as indicated on the motor nameplate to insure proper voltage and phase.

A ground wire must run from the blower

motor housing to a suitable electricalground, such as a properly grounded metallic raceway or a ground wire system.

OPTIONAL HEAT SLINGERThe optional split-type aluminum heatslinger should be installed on the blowershaft, between the housing and inboardbearing, with the fins (blades) facing thebearing. Position the heat slinger as close to the bearing as possible withouttouching. Tighten the hex head boltssecurely. A safety guard should beinstalled over the heat slinger.

NOTE: If a heat shield is installed betweenmotor and housing, the maximum inlettemperature is increased to 500ºF forthose blowers using a heat slinger.

NOTE: The safety guard is not providedwith the heat slinger. Provided by others.

2. After electrical connections are completed, apply just enough power to start the unit. Be sure that the rotation of the wheel is correct as indicated by directional arrows on the unit. If proper rotation, apply full electrical power.

3. With the air system in full operation and all ducts attached, measure current input to the motor and compare with the nameplate rating to determine if the motor is operatingunder safe load conditions.

Model Compatible Heat Slinger Model

3C539 4C7843C106 4C7843C107 4C7903C108 4C7913C540 4C792

Heat Slinger Compatibility Chart

MaintenanceBefore attempting any repair work,

be certain that all power to the motorand electrical accessories are turned offand locked in off position.

1. Pillow block ball bearings:

a. Inspect and tighten all bearing collar set screws after the first 50 to 100 hours of operation and periodically thereafter.

b.Lubricate the blower bearings while the shaft is rotating, use a good grade of ball bearing grease, (Shell Oil Co., Alvania #2, Texaco Premium, RB, Exxon Unirex N2, Mobil 532, or equal). Apply with a hand gun until a slight bead of grease is noticeable around the bearing seal. Stop lubrication when the bead is formed. DO NOT OVERLUBE.

c. Bearings that have been stored for any period of time must be lubricated before startup.

Models 3C106,3C107, 3C108,3C539 and 3C540

7


®

ENGLISH

d.Refer to Lubrication Guide chart above.

e. Bearings are prelubricated at the factory. At higher RPMs, any excess grease will escape from the bearingseals. This condition is normal.

f. Relubrication intervals depend on bIower application. When lubricating the bearings observe the following. If the bearing grease is clean you could extend the lubrication interval, but if the bearing grease is black and dirty the interval should be shortened.

2. Bearing Replacement: Wheel and shaft must be supported before any dismantling is attempted. Remove

drives, loosen and remove bearing bolts. Next loosen the retaining set screws on the bearing collars. Remove the bearings from the shaft only after the wheel and shaft are securely supported.

3. Shaft Removal: After following the steps listed for the removal of the bearings, loosen the set screws in the wheel hub. With the wheel securely blocked, pull the shaft from the wheel.

4. Wheel Replacement: Remove the bolts on the inlet upright support. Loosen set screws on wheel hub and lift wheel from housing.

Speed Bearing Greasing

RPM Temperature Condition Interval

0-100 To 140°F Clean 6-12 Mo.

101-1500 To 140°F Clean 2-6 Mo.

Over 1500 To 140°F Clean or Dirty 1 Wk.-1 Mo.

Over 1500 To 200°F Clean or Dirty Daily-2 Wk.

Lubrication Guide4. Motor will be overloaded if blower RPM exceeds that recommended inperformance table, or if operated below static pressure shown.

Do not exceed6,600 FPM inlet or

outlet velocity. At this air speed, theforce of the air could damage theblower or duct work. Refer to figure 3for inlet/outlet areas.

Inlet/Outlet Velocity(FPM)

CFM= Sq. Ft.

Inlet/Outlet area

8


ENGLISH

For Repair Parts, call 1-800-323-062024 hours a day - 365 days a yearPlease provide the following information:-Model number-Serial number (if any)-Part description and number as shown in parts list

Figure 5 – Repair Parts Illustration

3C106, 3C107, 3C108, 3C539 and 3C540

Repair Parts List

9

®

ENGLISH

Repair Parts List

Reference Number Description 3C106 3C107 3C108 3C539 3C540 QTY.

1 Frame 203-09-4058-6 203-11-4057-6 203-13-4049-6 203-07-4002-6 612-26-4010-6 1

2 Wheel 202-15-4023-5 202-19-4021-5 202-22-4031-5 202-12-4009-5 202-26-4071-5 1

3 Housing 201-09-4013-5 201-19-4001-5 201-22-4001-5 201-07-4001-5 201-26-4002-5 1

4 Inlet upright 617-09-4002-5 617-11-4002-5 617-13-4003-5 617-07-4001-5 617-26-4001-5 1

5 Shaft 604-19-6040-5 604-23-6070-5 604-27-6012-5 604-19-6093-5 604-31-6017 1

6 Bearings 805-19-6007-5 805-23-6006-5 805-27-6005-5 805-19-6007-5 805-31-6005-5 2

7 Motor base 625-00-7005-5 625-00-7002-5 625-00-7002-5 625-00-7005-5 625-00-7075-5 1

8 J-Bolts 876-00-6007-5 876-00-6006-5 876-00-6006-5 876-00-6007-5 876-00-6006-5 2

9* Hex. hd. nut 3/8”-16 (16 req.) 3/8”-16 3/8”-16 5/16”-18 (16 req.) 3/8”-16 32

10* Lock washer 3/8” (16 req.) 3/8” 3/8” 5/16” (16 req.) 3/8” 32

12* Hex hd. bolt 1/2-13 x 2” 1/2-13 x 2” 5/8-11 x 21/2” 1/2-13 x 2” 5/8-11 x 21/2” 4

13* Flat washer 1/2” 1/2” 5/8” 1/2” 5/8” 8

14* Lock washer 1/2” 1/2” 5/8” 1/2” 5/8” 4

15* Hex hd. nuts 1/2”-13 1/2”-13 5/8”-11 1/2”-13 5/8”-11 4

16* Hex hd. bolt 3/8”-16 x 1 3/8”-16 x 1 3/8”-16 x 1 3/8-16 x 1” 1/2-13 x 11/4” 2

17* Lock washer 3/8” 3/8” 3/8” 3/8” 1/2” 2

18* Hex nuts 3/8”-16 1/2”-13 1/2”-13 3/8”-16 1/2”-13 6

19* Lock washer 3/8” 1/2” 1/2” 3/8” 1/2” 6

21* Key stock 1/4 x 1/4” x 21/2” 3/8 x 3/8 x 3” 3/8 x 3/8 x 3” 1/4 x 1/4 x 21/2” 1/2 x 1/2 x 4” 1

22* Key stock 1/4 x 1/4” x 4” 3/8 x 3/8 x 4” 3/8 x 3/8 x 4” 1/4 x 1/4 x 21/2” 1/2 x 1/2 x 5” 1

23* Set screw 5/16-18 x 3/4” 3/8-16 x 3/4” 3/8-16 x 3/4” 5/16”-18 x 3/4” 1/2-13 x 1” 1

24* Set screw 5/16-18 x 1” 3/8-16 x 1” 3/8-16 x 1” 5/16”-18 x 3/4” 1/2-13 x 11/2” 1

▲ Weatherproofdrive cover 660-09-4024-5 660-11-4018-5 660-11-4018-5 660-07-4005-5 660-15-4001-5 1

Part Numbers for Model:

Dayton Operating Instructions and Parts Manual 3C106, 3C107, 3C108, 3C539 and 3C540

(*) Standard Hardware item, available locally.(▲) Not shown.

10


ENGLISH

3C106, 3C107, 3C108, 3C539 and 3C540


®

Excessive noise 1. Wheel rubbing on housing 1. Center wheel2. Loose wheel on shaft 2. Tighten wheel set screw3. Loose motor or blower sheave 3. Tighten sheave set screw4. Belts too loose 4. Adjust belt tension after 24 hours operation5. Belts too tight 5. Loosentomaintain 3/4"deflection per ft.of span between sheaves 6. Worn belt 6. Replace7. Motor base or blower not securely anchored 7. Tighten mounting bolts8. Worn bearings 8. Replace

Insufficient air flow 1. Blower speed too low 1. Check for correct drives as shown under“Drive Data”2. Dampers or registers closed 2. Open3. Dirty or clogged filter 3. Clean or replace4. Leaks in duct work 4. Repair5. Elbows, cabinet walls, or other 5. Correct obstructions to restrict fan inlet6. Belt slippage 6. Adjust belt tension

Too much air flow 1. Blower fan speed too high 1. Check for correct drives as shown under“Drive Data” 2. Filter(s) not in place 2. Install filter(s) 3. Insufficientstaticpressure (SP), (Airflow resistance) 3. Induce Sp into system ductwork

Unit fails to operate 1. Blown fuse or open circuit breaker 1. Replace fuse or reset circuit breaker 2. Broken drive belt 2. Replace3. Defective motor or capacitor 3. Replace

Motor overheats 1. Blower speed too high or motor horsepower too low 1. See “Drive Data” for correct drives and motor horsepower required2. System static pressure too low 2. Check static pressure and correct system accordingly3. Shorted windings in motor 3. Replace motor

Excessive vibration 1. Bearing and drive alignmert 1. Realign2. Mismatched belts 2. Replace3. Loose wheel on sheaves or shaft 3. Tighten4. Loose or worn bearings 4. Replace5. Loose mounting bolts 5. Tighten6. Motor out of balance 6. Replace7. Wheel out of balance 7. Replace or rebalance 8. Sheaves eccentric or out of balance 8. Replace9. Accumulation of material on wheel 9. Clean

Symptom Possible Cause(s)

Troubleshooting Chart

Corrective Action

Models 3C106,3C107, 3C108,3C539 and 3C540

11


®

ENGLISH

LIMITED WARRANTYDAYTON ONE-YEAR LIMITED WARRANTY. Dayton® Radial Blade Belt-Driven Blowers, Models covered in thismanual, are warranted by Dayton Electric Mfg. Co. (Dayton) to the original user against defects in workmanshipor materials under normal use for one year after date of purchase. Any part which is determined to be defectivein material or workmanship and returned to an authorized service location, as Dayton designates, shipping costsprepaid, will be, as the exclusive remedy, repaired or replaced at Dayton’s option. For limited warranty claimprocedures, see PROMPT DISPOSITION below. This limited warranty gives purchasers specific legal rights whichvary from jurisdiction to jurisdiction.

LIMITATION OF LIABILITY. To the extent allowable under applicable law, Dayton’s liability for consequentialand incidental damages is expressly disclaimed. Dayton’s liability in all events is limited to and shall not exceedthe purchase price paid.

WARRANTY DISCLAIMER. Dayton has made a diligent effort to provide product information and illustrate theproducts in this literature accurately; however, such information and illustrations are for the sole purpose ofidentification, and do not express or imply a warranty that the products are MERCHANTABLE, or FIT FOR APARTICULAR PURPOSE, or that the products will necessarily conform to the illustrations or descriptions. Exceptas provided below, no warranty or affirmation of fact, expressed or implied, other than as stated in the“LIMITED WARRANTY” above is made or authorized by Dayton.

PRODUCT SUITABILITY. Many jurisdictions have codes and regulations governing sales, construction,installation, and/or use of products for certain purposes, which may vary from those in neighboring areas. WhileDayton attempts to assure that its products comply with such codes, it cannot guarantee compliance, andcannot be responsible for how the product is installed or used. Before purchase and use of a product, review theproduct applications, and all applicable national and local codes and regulations, and be sure that the product,installation, and use will comply with them.

Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allowthe exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may notapply to you; (b) also, some jurisdictions do not allow a limitation on how long an implied warranty lasts,consequently the above limitation may not apply to you; and (c) by law, during the period of this Limited Warranty, any implied warranties of implied merchantability or fitness for a particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise disclaimed.

PROMPT DISPOSITION. Dayton will make a good faith effort for prompt correction or other adjustment withrespect to any product which proves to be defective within limited warranty. For any product believed to bedefective within limited warranty, first write or call dealer from whom the product was purchased. Dealer willgive additional directions. If unable to resolve satisfactorily, write to Dayton at address below, giving dealer’sname, address, date, and number of dealer’s invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier. If product was damaged in transit to you, file claim with carrier.

Manufactured for Dayton Electric Mfg. Co., 5959 W. Howard St., Niles, Illinois 60714 U.S.A.

Notes

Dayton Operating Instructions and Parts Manual 3C106, 3C107, 3C108, 3C539 and 3C540

Manufactured for Dayton Electric Mfg. Co.Niles, Illinois 60714 U.S.A.

®

ENGLISH

Documents

property damage! Retain instructions for future … · Dayton radial blade belt-driven blowers are used to move air and material. ... Wheel and housing are constructed of steel