PROMOUNT BACKING SYSTEM · notched track backing and other screwed and welded backing methods that are built-up and result in material overlaps. The ProMount Backing system is a cost

ProMount “Stick & Stay” Flush Mount Backing System Benefits/Advantages• Easily Installs with “Stick & Stay” Mounting Adhesive• Adjusts to various stud layout and stud spacing – installs one stud bay at a time.• Works with 1-1/4”, 1-5/8”, 2”, 2-1/2” and 3” stud flanges – one part does it all.• Low Profile Flange to accommodate vertical “in-wall” MEP trades work without notching.• Save Money, Re-Use STUD and TRACK scrap material as backing• Meets OSHPD, ADA, DSA wall backing standards – IBC 2012 / CBC 2013• Mounts FLUSH with the framing surface. No “Material Build-up” for smoother, flatter drywall. No Screw Pops.• Approved for Type 1, Type 2, Type 3 and Type 4 Backing Loads

Basic UseProMount is a light gauge steel backing [mounts] system and backing plates that install stud bay-by-stud bay, eliminating the troubles of notched track backing. ProMount backing mounts are secured together with an adhesive label that enables it to be easily installed on vertical studs. ProMount backing plates (PBP) are designed with low profile returns allowing maximum in-wall [stud cavity] space for MEP trades installed work. The ProMount components install flush with the stud members, eliminating excess material build–up. Moreover, standard 6-inch (33 mil. or 54 mil. or greater) stud and track scrap materials can be re-used and installed as backing plates. This pre-engineered framing system can be used in lieu of flat strap backing, notched track backing and other screwed and welded backing methods that are built-up and result in material overlaps. The ProMount Backing system is a cost effective means of installing backing when stud lay out varies.

ProMount is made of 16-gauge and 14-gauge (54 & 68 mil.) galvanized steel complying with industry standard ASTM performance criteria for metal stud framing members. The members fasten with No. 10 sheet metal screws (SMS).

Code Compliance• Seismic Design Criteria (Max.)

Fp calculated with: SDS = 2.10 (MAX.) & Ip = 1.0 SDS = 1.40 (MAX.) & Ip = 1.5 z/h = 1

• For greater design criteria contact CEMCO technical services for project specific design.

• International Building Code 2012 (IBC) California Building Code 2013 (CBC)

• America Disability Act (ADA): ProMount meets the load requiems of ADA America Disability Act section 4.26 Handrails, Grab Bars and Tub and Shower Seats. 250 point loading is achieved in the maximum bending moment, shear stress, direct and torsional stresses, lateral load, direct tension force, and combined shear stress.

• OSHPD California Hospital Compliance: ProMount meets the load requirements of OSHPD for Full Height Cabinets or Equipment, Base Cabinets or Equipment, Wall Cabinets or Equipment equal top 2010 CBC Standard Partition Wall Details, published Jan. 6th 2012.

PROMOUNT BACKING SYSTEM

Corporate Headquarters 263 North Covina LaneCity of Industry, CA 91744Phone: 800.775.2362Fax: 626.330.7598

Manufacturing FacilitiesCity of Industry, CA Denver, COFt. Worth, TXPittsburg, CA

Structural Engineering/Design1001-A Pittsburgh Antioch HwyPittsburg, CA 94565Phone: 800.775.2362Fax: 626.330.7598

Technical Services263 North Covina LaneCity of Industry, CA 91744Phone: 800.416.2278Fax: 626.249.5005

Corporate Headquarters & Main Manufacturing Facility263 N Covina Lane, City of Industry, CA 91744

Phone: 800.775.2362 | Fax: 626.330.7598

N. California Manufacturing Facility1001-A Pittsburg Antioch Hwy Pittsburg, CA 94565

Phone: 925.473.9340 | Fax: 925.473.9341

Denver Colorado Manufacturing Facility490 Osage Street, Denver, CO 80204

Phone: 303.572.3626 | Fax: 303.572.3627

Ft. Worth Texas Manufacturing Facility8600 Will Rogers Blvd., Ft. Worth, TX 76140

Phone: 817.568.1525 | Fax: 817.568.2759

PROMOUNT STICK & STAY ADHESIVE LABEL, CONNECTS PROMOUNT BRACKETS

US Patents 7,739,852 & 8,141,319. Owned by Brady Innovations, LLC.

ADHESIVE LABEL WITHINSTRUCTIONS PRINTED ON OUTSIDE







Phone: 800.775.2362 | Fax: 626.330.7598


Phone: 925.473.9340 | Fax: 925.473.9341


Phone: 303.572.3626 | Fax: 303.572.3627


Phone: 817.568.1525 | Fax: 817.568.2759

Member Designation/NomenclatureMember Identification shall be as shown:

1. Promount Nomenclature shall be as shown:

1 2 3

600 PBP 54-

1 600 Series Promount Backing System

2 Style: Example: Backing Plate = PBP The three designations utilized by the designator system are: PBP = ProMount Backing Plate

3 Material Thickness: Example: 0.054 in. = 54 mils; 1 in. = 1/1000 in. Material thickness is the minimum base metal thickness in mils. Minimum base metal thickness represents 95% of design thickness.

2. ProMount Backing Brackets are not required to be used in pairs on each backing stud.

3. Extend backing plate on bay beyond edge of cabinet or equipment to fasten to adjacent backing stud. However, backing plates are not required to continue an additional stud bay beyond equipment unless required by IOR.

4. See chart for approved use conditions for backing plates.

5. Minimum backing stud thickness is 33 mil. For backing studs with flanges larger than 2", 54 mil. is required.

6. PROMOUNT backing plates come in 14-3/8" lengths for 16" O.C. framing and 22-3/8" lengths for 24" O.C. framing. ProMount backing plates, stud sections and track sections can be cut to length to meet vertical stud bay spacing as required.

PROMOUNTBACKING PLATES

PROMOUNTBACKING BRACKETS

2.00

"

0.5000"

1.125"

(3) 0.17"Ø HOLES

0.875"0.

50"

0.50

"

0.60

"

0.6250"

6.00

" 600PBP-68600PBP-54

3.50

"

1.25"

16 GAUGE (54 MIL.) - 0.0566"

14 GAUGE (68 MIL.) - 0.0703"

2.625"

1.25" 0.375" 1.00"

4.50

"

0.50

"

0.75

0"







Phone: 800.775.2362 | Fax: 626.330.7598


Phone: 925.473.9340 | Fax: 925.473.9341


Phone: 303.572.3626 | Fax: 303.572.3627


Phone: 817.568.1525 | Fax: 817.568.2759

Light Gauge Steel / Material Standards1. Details on this sheet are acceptable alternates for backing details

shown in the contract documents.

2. All work shall meet the requirements of the following:

A. American Iron and Steel Institute (AISI) design of cold formed steel structural members

B. American Society for Testing and Materials (ASTM)

3. All materials conform to the following:

A. 54 mil (gauge) and heavier: 50 ksi min. yield, 65 ksi min. tensile strength galvanized steel per ASTM A653 - Grade 50

4. All calculated properties per AISI specification are based on the following thickness:

A. 14 Gauge (68 mil) — 0.0703" B. 16 Gauge (54 mil) — 0.0566"

5. Maintain a minimum of 3/8" edge distance between center of screw and edge of punchouts. Relocate screws if required.

6. Diagrams shown assume that the primary structure intended to support and resist loads produced by the interior framing system have been adequately designed for this purpose unless specifically noted.

7. Screws shall be #10 sheet metal screws with sufficient length to ensure penetration into steel stud by at least 3 full diameter threads.

8. Seismic info:

Fp calculated with: Sds = 2.10 (max) & Ip = 1.0 OR Sds = 1.40 (max) & Ip = 1.5 z/h = 1

9. This sheet is for the Promount Backing System only. The design of the backing studs and their attachment to the structure is not a part of this sheet.

TYPICALBACKINGLOCATIONS

USE CUT TRACK OR STUD AT STAIR HANDRAILS

TYPE 4 BACKINGAT ALL GRAB BARS

TYPE 1-4 BACKING DEPENDING ON VERTICAL LOAD REQUIREMENT. SEE CHARTS FOR EXAMPLES OF ITEMS SUPPORTED BY EACH BACKING TYPE.







Phone: 800.775.2362 | Fax: 626.330.7598


Phone: 925.473.9340 | Fax: 925.473.9341


Phone: 303.572.3626 | Fax: 303.572.3627


Phone: 817.568.1525 | Fax: 817.568.2759

Approved Use Chart

Backing TypeMinimum Thickness Approved Backing Plates

16" O.C. Studs 24" O.C. Studs

Type 1

(50# Vert., 35# Lat. per Stud Spacing)

600T150-33 600T150-33

600S162-33 600S162-33

PROMOUNT - 54 PROMOUNT - 54

Type 2


600T150-33 600T150-33

600S162-33 600S162-33


Type 3


600T150-54 600T150-54

600S162-54 600S162-54


Type 4(200# Vert., 141# Lat. per Stud Spacing,

200# any direction for handrail and 250# any direction for grab rails)

600T150-54 600T150-68

600S162-54 600S162-54


PROMOUNT

1/2"OR 5/8"

1-5/8" 1-1/2"

600S162-XX 600T150-XX

OROR

WALL STUDS BY OTHERS (33 MIL. MIN.)

PROMOUNT BRACKETBY BRADY INNOVATIONS

APPROVEDBACKING PLPER CHART

24" O.C. M

AX.

PROMOUNT BRACKETBY BRADY INNOVATIONS

(3) #10 TYPE BACKING PL IS NOT REQUIRED TO BE CENTERED ON BRACKETS

(3) #10 SMS TYP.







Phone: 800.775.2362 | Fax: 626.330.7598


Phone: 925.473.9340 | Fax: 925.473.9341


Phone: 303.572.3626 | Fax: 303.572.3627


Phone: 817.568.1525 | Fax: 817.568.2759

PUSH BRACKET ASCLOSE TO STUD FLANGEAS POSSIBLE AND FASTENAS REQUIRED 1/4" MAX GAP BETWEEN

BACKING PLATE AND STUD

BOXED STUDS WHERE OCCURS

USE PROMOUNT BRACKETEACH SIDE OF BACKING

BACK-TO-BACKSTUDS WHERE OCCURS

USE PROMOUNT BRACKET EACH SIDEOF BACKING PL

BRACKET CAN BE CUT FROM ADHERING STRIP

APPROVED BACKING PL

APPROVED BACKING PL

1/2"

1/2" MIN.

1/4" MAX. GAP BETWEEN BACKING PLATE AND STUD

NON-STRUCTURALSELF-ADHERING STRIP

Documents

PROMOUNT BACKING SYSTEM · notched track backing and other screwed and welded backing methods that are built-up and result in material overlaps. The ProMount Backing system is a cost