May/June 2010 (R7)

VAAGDEVI INSTITUTE OF TECHNOLOGY & SCIENCES

PRODDATUR.

Engineering Drawing Unit 7 Question Bank

1. (a) A right regular hexagonal prism of side of base 25 mm and altitude 55 mm has a square hole coincide one of the faces of the square hole is parallel to one of the faces of the hexagon. Draw the isometric projection of a prism with the hole.

(b) A cylinder of base 50 mm diameter and axis 70 mm long is lying on the H.P. Draw its isometric projection when the axis is horizontal. May/June 2010 (R7) Civil Engineering2. A cylinder 50 mm diameter and 60 mm height stands on H.P.A section perpendicular to V.P, inclined at 550 to HP cuts the cylinder and passes through a point on the axis at a height of 45 mm above the base . Draw the isometric projection of the truncated portion of the cylinder, when the cut surface is clearly visible to the observer.

May/June 2011 (1) ECE3. A pentagonal pyramid, 30 mm edge of base and 65 mm height , stands on H.P such that an edge of the base is parallel to VP and nearer to it .A section plane perpendicular to VP and inclined at 300 to HP cuts the pyramid passing through a point on the axis at a height of 35 mm from the base. Draw the isometric projection of the truncated pyramid.

May/June 2011 (2) ECE4. (a) Draw the isometric projection of a triangular pyramid of side of base 35 mm and height 75 mm when it is resting on H.P. such that an edge of the base is parallel to V.P.

(b) Draw the isometric projection of a cone of base 40 mm diameter and height 58 mm when it rest with its base on H.P.( axis is vertical)

May/June 2011 (3) ECE5. (a) Draw the isometric projection of a rectangular prism of base 50 mm X40 mm and height 75 mm , when it rest with its base on H.P. and one of its rectangular faces is parallel to V.P.

(b) Draw the isometric projection of a hollow rectangular prism of base 50X40 mm (outside), height 75 mm and thickness 8 mm when its axis is horizontal.

May/June 2011 (4) ECE6. A square pyramid with base edge 85 mm and height 125 mm , is resting on a cube of side 100mm.The axes of the solids coincide along a line. The two sides of the base of the pyramid are parallel to the edges of the cube. Draw the isometric view of the combination of the solids. May/June 2011 (1) EEE

7. A circular block of 75 mm diameter and 25 mm thick, is pierced centrally through its at faces, by a square prism of base 35 mm side and 125 mm long ,which comes out equally on both sides of the block . Draw the isometric projection of the combination when the combined axis is horizontal.

May/June 2011 (2) EEE

8. (a) A cylinder of base 50 mm diameter and axis 70 mm long is lying on the H.P. draw its isometric projection when the axis is horizontal.

(b) Draw the isometric projection of a hexagonal pyramid of side of base 30 mm and height 75 mm , when it is resting on H.P. such that an edge of the base is parallel to V.P.

May/June 2011 (3) EEE

9. A hexagonal prism , side of base 25 mm and height 50 mm rests on H.P. and one of the edges of its base is parallel to V.P .A section plane perpendicular to V.P. and inclined at 500 to H.P. bisects the axis of the prism . Draw the isometric projection of the truncated prism.

May/June 2011 (4) EEE

10. Draw the elevation, plan and left and right side views of the bracket shown in the picture below (dimensions in mm)

May/June 2011(1)11. Convert the bracket shown in the pictorial view below into orthogonal projections of three views.

May/June 2011(2) CSE12. Draw the elevation, plan and left and right side views of the bracket shown below in pictorial view (dimensions in mm)

May/June 2011(3) CSE13. Convert the part shown in the pictorial view below into orthogonal projections of three views (dimensions in mm)

May/June 2011(4) CSE14. A hexagonal prism , side of base 25 mm and height 50 mm rests on H.P. and one of the edges of its base is parallel to V.P .A section plane perpendicular to V.P. and inclined at 500 to H.P. bisects the axis of the prism . Draw the isometric projection of the truncated prism. Dec 2010.(R09) Aeronautical Engineering15. Draw the elevation, plan and left and right side views of the bracket shown in the picture below (dimensions in mm)

December 2010.(R09) Mechanical Engineering16. Draw the front view, top view and left side view of the object shown below (dimensions in mm).

December 2010.(R09) CSE17 Draw the front view, top view and right side view of the object shown below

(dimensions in mm)

November/December 2011(R9) EEE

18. Two views of a casting are shown below. Draw the isometric view of the casting

(dimensions are in mm)

November/December 2011(R9) ECE

19. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

November/December 2011(R9) CSE

20. Three views of a casting are shown below. Provide isometric view of the casting (dimensions

are in mm)

May/June 2010(1) EEE

21. Draw the isometric view of the casting whose views are given below. (dimensions are in mm)

May/June 2010(2) EEE

22. Three views of a machine part are shown below. Draw the isometric view of the part (dimensions are in mm)

May/June 2010(3) EEE

23. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(4) EEE

24. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(1) ECE

25. Three views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(2) ECE

26. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(3) ECE

27. Three views of a model are given below. Draw the isometric view of the model (dimensions are in mm)

May/June 2010(4) ECE

28. Two views of a casting are shown below. Draw the isometric projection of the casting (dimensions are in mm)

May/June 2010(1) CSE

29. Two views of a casting are shown below. Draw the isometric projection of the casting (dimensions are in mm)

May/June 2010(2) CSE

30. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(3) CSE

31. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May/June 2010(4) CSE

32. Three views of a casting are shown below. Draw the isometric view of the casting (dimensions are inmm)

May/June 2010(R7) Civil Engineering

33. Two views of a casting are shown in figure. Draw the isometric projection of the casting. (dimensions are in mm)

December 2010(R7) EEE

34. Convert the bracket shown in the pictorial view below into orthogonal projections of three views.

May 2012(1) ECE35. Draw the elevation, plan and left and right side views of the bracket shown in the picture below (dimensions in mm)

May 2012(2) ECE36 Two views of a piece are given below. Draw the isometric view of the piece (dimensions are in mm)

May 2012(3) ECE37. Three views of a model are given below. Draw the isometric view of the model (dimensions are in mm)

May 2012(4) ECE38. Draw the elevation, plan and left and right side views of the bracket shown in the picture below (dimensions in mm).

May 2012(1) CSE39. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm)

May 2012(2) CSE40. Two views of a bracket are given below. Draw the isometric view of the bracket (dimensions are in mm)

May 2012(3) CSE41. Three views of a machine part are shown below. Draw the isometric view of the part (dimensions are in mm)

May 2012(4) CSE42. Draw the front view, top view, right and left side views of the object shown below (dimensions in mm).

November/December 2012(R09) EEE43. Two views of a casting are shown below. Draw the isometric view of the casting (dimensions are in mm).

May 2012(1) EIE44. Two views of a model are shown below. Draw the isometric projection of the model (dimensions are in mm).

May 2012(2) EIE45. Two views of a casting are shown below. Draw the isometric projection of the casting (dimensions are in mm)May 2012(4) EIE

46. Draw the elevation, plan and left and right views of the step model shown in the picture below (dimensions in mm).

May 2012(4) EIE