7
1 See all emulators Program Use Daewoo 1 ECU with white – red socket ECU with blue socket

Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

  • Upload
    others

  • View
    21

  • Download
    0

Embed Size (px)

Citation preview

Page 1: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

1

See all emulators

Program Use

Daewoo 1• ECU with white – red socket• ECU with blue socket

Page 2: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

2

See all emulators

Wiring colour codes

The LED behavior

diagnostic mode - it flashes every second

adjusting to the ECU – flashing 0,1 sec

after adjusting it lights constantly and blinks every other second

Page 3: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

3

See all emulators

Daewoo 1

USE

ECUs with white - red sockets and ECUs with blue sockets

ECU with white – red socketThis emulator requires modification of Motorola HC11F1 processor located in ECU.

In address 010 write value 73 00 73 00twice

Page 4: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

4

See all emulators

Once you modified Motorola, connectemulator to the ECU as pictured.

Before connecting the emulator, itmust be precisely insulated withinsulation tape and the original

immobiliser must be disconnected!!!

In case of problems with starting the car,disconnect power supply (+12V) in ECU

and connect +12V ACC in place ofpower supply.

Page 5: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

5

See all emulators

ECU with blue socket

This emulator requires modification of Motorola HC11F1 processor located in ECU

In address 010, write value 73 00 73 00 twice

Once you modified Motorola, connect emulator to the ECU as pictured.

Page 6: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

6

See all emulators

Disconnect immo or cut off pin B7 from ECU

Before connecting the emulator, it must be precisely insulated with insulation tape and theoriginal immobiliser must be disconnected!!!

In case of problems with starting the car, disconnect power supply (+12V) in ECU and connect+12V ACC in place of power supply.

Page 7: Program Use - CARLABIMMO Immo Off emulator and software · and connect +12V ACC in place of power supply. 5 See all emulators ECU with blue socket This emulator requires modification

7

See all emulators

Warning!!!

Due to possible construction changes of cars, check signals with multimeter in the ECU plug.

All rights reserved.Unauthorized copying, hiring, lending, public performance will be punished!

We state that we are the only authentic authors of this manual. We possess copyright of thispublication. Any trials of unauthorized copying, hiring, quoting prohibited!!! Both service and

advertisement constitute copyright and they are the subject to the protection in accordance with theAct from 4th Feb. 1994 on Copyright and Related Laws (Statute Book no. 24 position 93) and

protection on the basis of the Act from 8th June 1993 on combating an unfair competition (StatuteBook no. 47 position 211)

www.carlabimmo.com

Last updated 15.01.2018