MINITEC NEWS 2009 1

NEWS 2009

Part. N° 95.0423/0

TABLE OF CONTENT INTRODUCTION

2 MINITEC NEWS 2009

CONTENTS3 END CAP Z WITH HAMMER TAPS

3 END CAP 45X45 VA

4 ANGLE 25 GD-Z

4 ANGLE 45X90 GD-Z

5 ANGLE 90 GD-Z

5 HINGE 19 S

6 HINGE 32 S

6 HINGE 45 S

7 DOOR HINGE SMALL

7 DOOR HINGE LARGE

8 T-SLOT MAGNET

8 SEALING PROFILE

9 SLIDE LR6 COMPACT

9 SLIDE LR6 COMPACT

10 RAIL LR 6 COMPACT

10 UNIVERSAL CLAMPING SOCKET

11 SLIDE G 32

11 BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT

12 CENTER DRIVE - 3 WHEELS SYSTEM

12 CUP HOLDER

MINITEC NEWS 2009 3

END CAP Z WITH HAMMER TAPS Part. N° 22.1007/1

TECHN. DATA/ITEMS SUPPLIED

- End cap 19x45 Z Part N° 22.1001/1

- End cap 32x32 Z Part N° 22.1002/1

- End cap 45x45 Z Part N° 22.1004/1

- End cap 45x90 Z Part N° 22.1007/1

APPLICATIONS

- Good clamping effectiveness via hammer taps in the star-shaped hole

- Simple disassembly

- The end cap can be re-used with replacement pins

ASSEMBLY

- Hammer the taps flush using a plastic hammer

- For dismantling, hammer the pin with a ø 4 centre punch

- Replacement pins (10 pack) Part N° 221009/1

END CAP 45X45 VA Part. N° 21.0026/0

TECHN. DATA/ITEMS SUPPLIED

- End cap stainless steel

- With fixing pan head screw M8 x 10 stainless steel

APPLICATIONS

- For Profile VA and Profile AL

- ESD on request

- Rounded edges

ASSEMBLY

- Tap an M8 thread 12 mm deep into the profile

- Place the end cap on and turn until the screw safety catches

- Screw in the screw included in the scope of delivery with SW4

4 MINITEC NEWS 2009

ANGLE 25 GD-Z Part. N° 21.0969/0

TECHN. DATA/ITEMS SUPPLIED

- Aluminium GD, powder coated, grey

- Fixing kit

- Removable centering tabs

- Weight 0,066 kg

APPLICATIONS

- General constructions, particularly useful for subsequent fitting of profiles into existing constructions

- Fixing of panel elements, table tops

- Strengthening of profile constructions

ASSEMBLY

- Use fixing kit from supply schedule

- Break centering tabs with pliers if non-aligning grooves

- For subsequent mounting into vertical profiles use square nut M8 with position-fixing Part N° 21.1351/2

- End cap MW 25 GD-Z Part. N° 22.0997/1

ANGLE 45X90 GD-Z Part. N° 21.1397/0

TECHN. DATA / ITEMS SUPPLIED

- Aluminium GD, powder coated, grey

- Fixing kit

- Weight 0,281 kg

APPLICATIONS

- General constructions, particularly useful for subsequent fitting of profiles into existing constructions

- Fixing of panel elements, table tops

- Strengthening of profile constructions

ASSEMBLY

- Use fixing kit from supply schedule

- For mounting into vertical profile use square nut M8 with position-fixing Part N° 21.1351/2

- Recommended locking torque 20 Nm

- Use hammer-head screw Part N° 21.1370/0

- Suitable end cap MW 45x90 GD-Z Part N° 22.0998/1

MINITEC NEWS 2009 5

ANGLE 90 GD-Z Part. N° 21.0978/0

TECHN. DATA / ITEMS SUPPLIED

- Aluminium GD, powder coated, grey

- Fixing kit

- Weight 0,460 kg

APPLICATIONS

- For profiles 90 and 180

- General constructions, particularly useful for subsequent fitting of profiles into existing constructions

- Fixing of panel elements, table tops

- Strengthening of all profile connections

ASSEMBLY

- Use fixing kit from supply schedule

- For subsequent mounting into vertical profiles use square nut M8 with position-fixing Part N° 21.1351/2

- Hammer head screw can be used

- Recommended locking torque 20 Nm

- Suitable end cap MW 90 GD-Z Part N° 220999/1

HINGE 19 S Part. N° 21.1044/0

TECHN. DATA / ITEMS SUPPLIED

- Aluminium GD, powder coated, grey

- Without fixing kit

- with end caps

- Weight 0,100 kg

- Load max. 600 N

APPLICATIONS

- Suitable for large doors and flaps of profile type 19 or 32

- Guard units

- Connection of profiles 19 and 32 at any angle

ASSEMBLY

- Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove, or with screws corresponding to the material thickness directly on the panel elements

- For heavy-duty applications use multiple hinges

6 MINITEC NEWS 2009

HINGE 32 S Part. N° 21.1055/0

TECHN. DATA / ITEMS SUPPLIED

- Aluminium GD, powder-coated, grey

- Without fixing kit

- With end caps

- Weight 0,105 kg

- Load max. 600 N

APPLICATIONS

- Suitable for large doors and flaps

- Guard units

- Connection of profiles 19, 32 and 45 at any angles

ASSEMBLY

- Fasten hinge with 4 M6 x 18 bolts and 4 square nuts on the profile groove or with screws corresponding to the material thickness directly on the panel elements

- Fasten hinge with M8 x 30 bolt on the 45 x 45 profile face side; fasten the other hinge half with M6 x 20 bots and square nuts on the profile groove or with M6 x 18 bolts corresponding to the material thicknes

- For heavy-duty applications use multiple hinges

HINGE 45 S Part. N° 21.1098/0

TECHN. DATA / ITEMS SUPPLIED

- Aluminium GD, powder-coated, grey

- Without fixing kit

- With End caps

- Weight 0,110 kg

- Load max. 600 N

APPLICATIONS

- Suitable for large doors and flaps

- Guard units

- Connection of profiles at various angles

- For higher loads use more hinges

ASSEMBLY

- 1: 2 screws M8 x 30

- 2: 2 screws M6 x 18, square nuts M6, 1 screw M8 x 30

- 3: 2 screws M6 x 18, 2 square nuts M6, 2 screws M6 for panel element according to material

- 4: 4 screws M6 x 18, 4square nuts M6

MINITEC NEWS 2009 7

DOOR HINGE SMALL Part. N° 21.0973/0

TECHN. DATA/ITEMS SUPPLIED

- Aluminium

- Fixing kit

- Weight 0,120 kg

APPLICATIONS

- Suitable for large doors and lids

- Guard units

- Connection of profiles at any angle

ASSEMBLY

- Use fixing kit from supply schedule

DOOR HINGE LARGE Part. N° 21.0970/0

TECHN. DATA/ITEMS SUPPLIED

- Aluminium

- Fixing kit

- Weight 0,235 kg

APPLICATIONS

- Suitable for large doors and lids

- Guard units

- Connection of profilles at any angle

ASSEMBLY

- Use fixing kit from supply schedule

8 MINITEC NEWS 2009

T-SLOT MAGNET Part. N° 21.0023/0

TECHN. DATA/ITEMS SUPPLIED

- 1 Magnet NeFeB zinc-plated

- Without fixing kit

- Weight 0,13 kg

- Attention: Electric- and memory devices can be faulted by the magnet

APPLICATIONS

- Adhesive magnet for tools

- Below conveyors as guidance, for magnetisable trnasported material or for higher conveyiry speed

ASSEMBLY

- Insert magnet into t-slot

- For fixing: (strongly recommended) Use end cap Al, set screw M8 x 12 with square nut M8 or t-slot bar

SEALING PROFILE Part. N° 22.1011/0

TECHN. DATA/ITEMS SUPPLIED

- Weight 0,122 kg/m

- Length 100 m

APPLICATIONS

- Sealing of doors, lids and other constructions against water, dust and noise

ASSEMBLY

- Press into profile groove

MINITEC NEWS 2009 9

SLIDE LR6 COMPACT Part. N° 28.0140/0

TECH. DATA / ITEMS SUPPLIED

- Aluminium, all faces machined

- 3 Double row, angular-contact bearings

- Assembled ready for use

- Weight 0,194 kg

APPLICATIONS

- MiniTec linear guide systems LR 6

- Material-handling

- Measuring devices

- Doors

ASSEMBLY

- Slip slide onto rail

- Adjust clearance with key 2,5 A/F

- Tighten fixing screw with a torque of 20 Nm

SLIDE LR6 COMPACT Part. N° 28.0127/0

TECHN. DATA/ITEMS SUPPLIED

- Slide PEUHMW, black

- With square nut M8, steel zinc-plated

- Weight 0,068 kg

APPLICATIONS

- Material-handling

- Measuring devices

- Doors

ASSEMBLY

- Slip slide onto rail

- Adjust slide clearance with hexagon key

10 MINITEC NEWS 2009

RAIL LR 6 COMPACT Part. N° 28.0016/0

TECH. DATA / ITEMS SUPPLIED

- Aluminium, natural anodized E6/EV 1

- 2 Shafts Cf 53 h6, steel

- With fixing bores Ø 8,5 mm, grid: 150 mm

- Weight 1,779 kg/m

- Lenght 4 m

APPLICATIONS

- Material-handling

- Measuring devices

- Doors

ASSEMBLY

- Fasten rail with countersunk screws M8 x 20 and square nut M8 on MiniTec profile

UNIVERSAL CLAMPING SOCKET Part. N° P20.060/0

TECHN. DATA/ITEMS SUPPLIED

- Case PA 6 GF

- Knurled screw steel

- Weight 0,037 kg

APPLICATIONS

- For assembly of pneumatic switches for learning and training purposes

- To fasten diverse pneumatic switches

- Fastening of valves including those from different manufacturers

ASSEMBLY

- Simple pneumatic accessories fastened with M3 screws (not in scope of delivery) onto the clamping socket

- By pressing the knurled screw, the clamping socket can be fit into the slot

- When released, it is automatically indexed

MINITEC NEWS 2009 11

SLIDE G 32 Part. N° 28.0355/0

TECHN. DATA / ITEMS SUPPLIED

- Slide aluminium anodized

- Slide bearing (plastic)

- Without adjusting units

- Weight 0,314 kg

APPLICATIONS

- to adjust light barriers, reflectors, side guides etc.

ASSEMBLY

- Insert the slides of the mini adjustment unit into the sliding guides and turn the spindle

- Adjust using the play of the M6 tensioning screw

- Fasten the spindle bearing to the handle profile 32

BRACKET CONSOLE FOR MINIATURE ADJUSTMENT UNIT Part. N° 28.0371/0

TECHN. DATA/ITEMS SUPPLIED

- Console aluminium, natural anodized

- Without fixing kit

- Weight 0,044 kg

APPLICATIONS

- For connection of two adjustment units Part N° 28.0351/0, 28.0352/0 and 28.0353/0

- For connecting small loads, such as light barriers, sensors etc.

ASSEMBLY

- Each with two M6 threads, 10 mm deep, separation of 25 mm placed into slides

- Connect adjustment units with cylinder head screws M6x15

12 MINITEC NEWS 2009

CENTER DRIVE - 3 WHEELS SYSTEM Part. N° 29.5260/0

TECHN. DATA/ITEMS SUPPLIED

- Cylinder, steel zink-plated

- Ball bearings on both sides

- With Fixing kit

- Part. N° 29.5260/0 Weight with drive ø 50: 50,800 kg/m

- Part. N° 29.5261/0 Weight with drive ø 70: 70,566 kg/m

APPLICATIONS

- Space saving drive

- Motor below conveyor

- Suitable for nosebar on both ends

ASSEMBLY

- First install sheets

- Assemble driving drum, tensioning drive and bearing housing

- Assemble sprocked wheel, chain and motor. Adjust belt-tension after that

CUP HOLDER Part. N° 32.0544/0

TECHN. DATA/ITEMS SUPPLIED

- Cup holder aluminium anodized

- Cup with MiniTec company logo

- With fixing kit

- Weight 0,580 kg

APPLICATIONS

- Cup or bottle holder for workplace systems

- With cut-out for cup handel

ASSEMBLY

- Screw on profile constructions by using fixing kit